Passenger Footpeg Mounting Kit Instruction Sheet - Harley
Contents
1. are properly installed footpegs will fold upward 3 at a 45 angle toward the rear of the motorcycle WARNING Footrests must fold up and toward rear of motorcycle if struck Failure to set footrests to fold up and back could result in death or serious injury 00366a 12 See Figure 5 Install a passenger footpeg purchased separately on each footpeg support as shown using a hex head cap screw 4 spring washer 5 and lock nut 6 from the kit BELT ADJUSTMENT AND VEHICLE ALIGNMENT Refer to REAR BELT DEFLECTION in the Service Manual and follow the procedures given to inspect and adjust rear belt deflection See the VEHICLE ALIGNMENT section in the Service Manual to properly align the vehicle 2of3 SERVICE PARTS is00513 Figure 5 Service Parts Passenger Footpeg Mounting Kit Table 1 Service Parts Table Item Description Quantity Part Number 1 Support passenger footpeg right side 49224 06 2 Support passenger footpeg left side 49230 06 3 Screw button head self tapping 3 8 16 x 1 in 4 4059 4 Cap screw hex head 3 8 16 x 1 1 2 in 2 4721 5 Spring washer 2 50912 72 6 Hex lock nut 3 8 16 2 7778 Items mentioned in text but not included in kit A Rear fork B Hole plug 2 C Belt guard mounting bracket D Passenger footpeg 2 J03792 3of32. cMOTOR HARLEY DAVIDSON WY J03792 INSTRUCTIONS REV 2005 05 18 PASSENGER FOOTPEG MOUNTING KIT GENERAL Kit Number 50210 06 Models This kit fits all 2006 and later Dyna model motorcycles with original equipment solo seat and no footpegs It is required when installing a 2 up seat on these models This kit is also a direct replacement for the standard equipment passenger footpeg footrest mounting brackets on 2006 and later Dyna models with original equipment 2 up seats Additional Parts Required Proper installation of this kit requires the installation of a pas senger footpeg on each mounting bracket See a Harley Dav idson dealer Refer to the appropriate Parts Catalog for original equipment footrests or see the current Harley Davidson Genuine Motor Accessories and Parts catalog for a selection of operator and passenger footpegs WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet references Service Manual information A Service Manual for your model motorcycle is required for this installation and is available from a Harley Davidson Dealer Special tools are required for the in
3. ck nut Hex head cap screw 2 Belt guard mounting bracket OPeONs Figure 3 Upper Belt Guard Removal 6 Remove the two hex head cap screws 4 that attach the belt guard mounting bracket 5 to the rear fork The bracket and screws can be discarded 7 See Figure 5 Obtain the left side footpeg support 2 and two self tapping screws 3 from the kit Install the support to the mounting location as shown and torque the screws to 25 35 ft lbs 34 47 Nm 8 Install the upper belt guard with the fasteners removed earlier Tighten the screws to 10 15 ft lbs 13 5 20 3 Nm 9 Install the debris deflector with the three screws removed earlier Tighten the screws to 40 60 in Ibs 4 5 6 8 Nm Right Side 10 Remove and discard the two plastic hole plugs B from the rear fork A J03792 11 Obtain the right side footpeg support 1 and two self tapping screws 3 from the kit Install the support to the mounting location as shown and torque the screws to 25 35 ft lbs 34 47 Nm Footpegs DN is00514 Q Li g E 1 Spring washer 2 Rounded side of mounting end 3 Footpeg MUST fold upward and to the rear Figure 4 Proper Footpeg Installation NOTES See Figure 4 The spring washer 1 goes between the jaws of the footpeg support bracket along with the mounting end of the footpeg Footpegs must be installed in the bracket with the rounded side 2 of the mounting end inboard When footpegs
4. stallation of this kit We recommend that this kit be installed by a factory trained tech nician at a Harley Davidson dealer Kit Contents See Figure 5 and Table 1 INSTALLATION Left Side 1 Block the motorcycle under the frame so the rear wheel is off the ground 2 See Figure 1 Remove the three self tapping screws 2 and remove the debris deflector 1 from the vehicle J03792 is00521 1 Debris deflector 2 Self tapping screws 3 Figure 1 Debris Deflector Removal See Figure 2 Remove the spring clip 1 from the left side of the rear axle Loosen but do not remove the rear axle nut 2 Turn the axle adjusters 3 on each side of the rear wheel counterclockwise about the same amount to move the rear wheel forward and allow slack in the drive belt 1 Spring clip 2 Rear axle nut 3 Rear axle adjuster 2 Figure 2 Rear Axle Nut and Adjusters Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled 1 of 3 Please dispose of materials responsibly NOTE When removing the belt guard make sure the belt guard does not contact the fender or the fender paint will be scratched 5 See Figure 3 Remove and retain the front 1 and rear 2 3 upper belt guard fasteners and carefully remove the upper belt guard from the vehicle is00515 Front button head screw and washer Rear button head screw and washer Hex flanged lo
Download Pdf Manuals
Related Search