http://www.corksport.com/corksport-led-light- kit-for-2014-mazda
Contents
1. Part Ati 9 011 CHKSPOFSC CorkSport Mazda 6 LED Light Kit 2014 Mazda 6 Thank you for purchasing the CorkSport Mazda 6 LED Light Kit CorkSport s LED light kit replaces the incandescent bulbs for the dome lights map light trunk front doors and license plate The lights simply plug in with no custom adapters or wiring required We hope you enjoy your new interior lighting Please let us know your feedback by submitting a review at http www corksport com corksport led light kit for 2014 mazda 6 html Pre Installation Notes Make sure your vehicle is completely cooled down prior to starting installation If you are going to work on your car within an hour or two of having driven it use a fan to cool off the car gt These instructions were written for reference only and the use of a factory service manual is b F Nore recommended Please read these instructions thoroughly prior to starting installation How our instructions work To best cover all of our customers experience levels we have NOTE included an overview checklist for the more technically advanced users along with step by step instructions for customers that require additional detail 5e NOTE These installation instructions were written using a 2014 Mazda 6 2014 Mazda 6 models Ba will be similar Materials and Time re P General Info Tooling List Parts List y tT Part Ati 9 011 Small2. fixture Remove the 1 screw using a 2 phillips screwdriver then pull the whole fixture downward and towards the front of the car It is a Snap fitting so it should pop out with a tug Figure 7c d Firmly grasp the OEM bulb and pull it strait out of the socket e Insert the new round T10 style LED into the socket If not working remove and rotate 180 degrees then re install f Re attached the light fixture to the dash with the screw and a 2 phillips screwdriver Figure 7d g Re install the glove in the reverse order it was Figure 7d removed k This completes the installation of your interior LED lighting Make sure all the lights are operating properly If not make sure all connections and fuses are good and the 5 LEDs are in the proper orientation What s Next CORKSPORT 2014 Mazda 6 SkyActiv Short Ram Intake One of the easiest and most beneficial performance enhancements you cando for your vehicle the CorkSport Power Series Short Ram Intake replaces your factory airbox with an open intake system allowing more air into the intake chamber Engineered with exacting tolerances the CorkSport SkyActiv Short Ram Intake includes our precisionmachined MAF housing made from billet aluminum a durable dry flow air filter and custom reinforced silicone connector Need Help With Yourdnstallatione Call 360 260 CORK 6 of 6
3. flat head screwdriver Four 4 31mm LED bulbs Time Est 0 5 hours A Four 5 T10 Wedge LED bulbs Wrench Rating 1 5 Two 2 28mm LED bulbs One 1 TS Wedge LED bulb Need Help With Yourdnstallatione Call 360 260 CORK Part Ati 9 011 Checklist This is an overview of each step in the build You can use this as a reference and a checklist as you button up the work on your car LED bulbs will only work when installed in one direction Test each bulb in the socket during installation If it does not work simply remove it turn it around and reinstall it Be careful when prying the covers off the factory bulb locations They should come off easily If they are hard to come off make sure you are prying in the correct orientation 1 Replacing the Front Overhead Interior Light LJ Remove the front overhead interior light cover shown in Figure 1a LJ Pull the bulb out of the socket circled in Figure 1b LJ Install one of the supplied LED s in the bulbs place shown in Figure 1c LJ Replace the cover that was removed in step 1a shown in Figure 1d L Repeat steps 1a 1d for the bulb on the other side 2 Replacing the Vanity Mirror Lights A Sport Models do not have the Vanity lights All other models will have these lights in the vanity mirrors LI Locate the Vanity light in the sun visor Shown in Figure 2a Ql Remove the cover of the light using a small flat head screw driver Figure 2b L Replace the factory b
4. on don t open the slide all the way b Remove the cover of the light using a small flat head screw driver Figure 2b shows how the assembly will look once the cover has been removed Notice the light is off with the slide partially open Figure 2a Figure 2b c Replace the factory bulb with the 28mm LED bulb d Repeat Steps 2a 2c for the other vanity light 3 Replacing the Door Convenience Lights a Locate the Door lights at the rear of the front doors Shown in Figure 3a To keep the light from coming on hold the switch at the door or tape the switch off with painters tape b Remove the cover of the light using a small flat head screw driver This on similar to the vanity Lights c Replace the factory bulb with the T10 LED bulb Figure 3a d Repeat Steps 3a 3c for the other vanity light Need Help With Yourdnstallatione Call 360 260 CORK 2 of 6 Part Ati 9 011 Detailed Instructions 4 Replacing the Rear Passenger Overhead Interior Light a Start by removing the light cover the same way that was recommended on the front overhead interior light in step 1a Use a small flat head screwdriver to pry the front side of the cover It will not take much effort The cover will then come right off shown in b Pullthe bulb out of the socket circled in If you need to use something to remove the bulb make sure it is non metallic or you may short out a fuse c Install one of the supplie
5. ace LI Replace the cover that was removed in step 5a 6 Replacing the License Plate Lights Q Start by locating the license plate bulb covers pictured in Figure 6a LJ With a small flat head pry the cover off Shown with a red arrow in Figure 6a LJ Pull the bulb out shown in Figure 6b LJ Install one of the supplied round LEDs in the bulbs place shown in Figure 6d LJ Replace the cover that was removed in step 6a L Repeat steps 6a 6e for the second license plate light bulb 7 Replacing the Glove Box Light L Start by opening the glove box and letting it fully open LJ Push in the sides of the glove box Figure 7a LJ On the right side there is a lever that connects to the damper Figure 7b Now the glove box will be free to pull from the dash Removing the light fixture using a 2 phillips screwdriver remove the 1 screw Replacing the bulb with a round T10 style LED 0D O O O Re install the parts in the reverse order as described above Ss p v You have finished the LED install checklist for further details and figures continue to the next page for the Detail Instructions Need Help With Your Installation Gall 360 260 CORK Part Ati 9 011 Detailed Instructions g These instructions were written using a 2014 Mazda 6 Mazda 6 models are similar 1 Replacing the Front Overhead Interior Light F LED Bulbs will only work when installed in one direction Test each bulb in the socket during instal
6. d LED s in the bulbs place shown in Check to see that it illuminates If it does not turn it around and reinstall it Face the LED bulbs straight down for maximum brightness or angle them slightly to diffuse the light a little d Replace the cover that was removed in step 4a Slide the back of the cover in first and then push the cover into place It will snap into place easily e Repeat steps 4a 4d to replace the bulb on the other side 5 Replacing the Trunk Light a Start by finding the cargo light in the trunk area pictured in b Again with a small flat head pry the light out shown in on next page Need Help With Your Installation Call 360 260 CORK 3 of 6 Part Ati 9 011 Detailed Instructions MAZDA PERFORMANCE 5 Replacing the Trunk and Cargo Area Light continued c Once the light has been removed pull the bulb out of the socket Again if you need to use something to remove the bulb make sure it is non metallic or you may short out a fuse d Again install one of the T5 LEDs in the bulbs place Check to see that it illuminates If it does not turn it around and reinstall it e Replace the cover that was removed in step 5a Slide the non switch side of the cover in first and then push Figure 5b the cover into place It will snap into place easily 6 Replacing the License Plate Lights a Start by locating the license plate bulb covers pictured in Figure 6a or F
7. igure 6c depending on trim package Figure 6a b Again with a small flat head pry the cover off Start with the clip on the side shown with a red arrow in Figure 6a and Figure 6c E Figure 6b then the cover should come off easily c Once the cover is off pull the bulb out shown in Figure 6b It should be snug in the socket but it will come out by hand Figure 6c Need Help With Yourdnstallatione Call 360 260 CORK 4 of 6 Part Ati 9 011 MAZDA PERFORMANCE 6 Replacing the License Plate Lights continued d Install one of the supplied round T10 LEDs in the bulbs place shown in Check to see that it illuminates e Replace the cover that was removed in step 6b Slide one side in first and then the other will snap into place as you press down f Repeat steps 6a 6e for the second license plate light bulb 7 Replacing the Glove Box Light a Open the glove box and push the sides in at the while gently pulling down b Disconnect the lever by pulling it in the direction of the Then rotate the glove box downward while pulling it towards the rear of the car It should slide off the pivot point in the dash Need Help With Yourdnstallatione Call 360 260 CORK 5 of 6 Part Ati 9 011 7 Replacing the Glove Box Light continued c Removing the light bulb fixture Looking up under the dash where the top of the glove box would be you will find the light bulb and it s
8. lation If it does not work simply remove it turn itaround and reinstall it Be careful when prying the covers off the factory bulb locations They should come off easily If they are hard to come off make sure you are prying in the correct orientation a Start by removing the light cover Use a small flat head screwdriver to pry the front side of the cover It will not take much effort The cover will then come right off shown in b Pull the bulb out of the socket circled in If you need to use something to remove the bulb make sure it is non metallic or you may short out a fuse c Install one of the supplied 31mm LED s in the bulbs place circled in Check to see that it illuminates If it does not turn it around and reinstall it Face the LED bulbs straight down for maximum brightness or angle them slightly to diffuse the light a little Wie d Replace the cover that was removed in step 1a Slide the back of the cover in first and then push the cover into place shown in It will snap into place easily e Repeat steps 1a 1d for the bulb on the other side Need Help With Your Installation Call 360 260 CORK 1 of 6 Part Ati 9 011 2 Replacing the Vanity Mirror Lights AN Sport Models do not have the Vanity lights All other models will have these lights in the vanity mirrors a Locate the Vanity light in the sun visor Shown in Figure 2a To keep the light from coming
9. ulb with the 28mm LED bulb Ll Repeat Steps 2a 2c for the other vanity light 3 Replacing the Door Convenience Lights L Locate the Door lights at the rear of the front doors Shown in Figure 3a LI Remove the cover of the light using a small flat head screw driver This on similar to the vanity Lights LJ Replace the factory bulb with the T10 LED bulb LI Repeat Steps 3a 3c for the other vanity light 4 Replacing the Rear Passenger Overhead Interior Light LJ Start by removing the light cover the same way that was recommended on the front overhead interior light in step 1a shown in Figure 4a LJ Pull the bulb out of the socket circled in Figure 4b LJ Install one of the supplied LED s in the bulbs place shown in Figure 4c Face the LED bulbs straight down for maximum brightness or angle them slightly to diffuse the light a little LI Replace the cover that was removed in step 4a Need Help With Your Installation Gall 360 260 CORK Part Ati 9 011 Checklist 4 Replacing the Rear Passenger Overhead Interior Light Continued LI Repeat steps 4a 4d to replace the bulb on the other side 5 Replacing the Trunk Light LJ Start by finding the cargo light in the trunk area pictured in Figure 5a LJ Again with a small flat head pry the light out shown in Figure 5b on next page LJ Once the light has been removed pull the bulb out of the socket LJ Again install one of the supplied LEDs in the bulbs pl
Download Pdf Manuals
Related Search