NISSAN RECALL CAMPAIGN BULLETIN
Contents
1. bolts screws that attach the left side instrument stay assembly cross brace support to the steering member assembly see Figure 3 b Clean the mounting surfaces and fastener threads c Reassemble and tighten the fasteners Example only Steering member support assembly and instrument stay assembl Steering member assembly cross brace Fasteners bolts nuts screws Clean threads and mounting 4 surfaces of Left side instrument stay assembly 0i cross brace support TP060036 Figure 3 4 5 5 Clean the negative battery cable connections a Write down all the radio presets b Disconnect the negative battery cable at the battery and at the body connection c Clean the following items e Negative cable to body connection eyelet both sides e Body connection bolt head and threads e Female bolt hole threads use correct size tap NOTE Do not remove paint from painted surfaces in the engine compartment to improve ground Doing so may cause corrosion rust e Battery negative post e Negative cable battery terminal d Reconnect negative battery cable at the body and the battery e Reprogram the radio presets 6 Use CONSULT II to erase all DTCs 7 Test drive and re check for DTCs 5 52. NISSAN NORTH AMERICA INC EN Technical Bulletin SERVICE BULLETIN Classification EC06 001a NTB06 009a March 31 2006 MIL ON WITH DTC U1000 OR U1010 STORED IN ENGINE CONTROL UNIT This bulletin has been amended The Applied Vehicles IF YOU CONFIRM and Claims Information sections have been changed No other content has been changed Discard all previous versions of this bulletin APPLIED VEHICLES 2002 2003 Maxima A33 2002 2006 Altima L31 2004 2006 Maxima A34 2005 2006 Xterra N50 2004 2006 Titan A60 2005 2006 Pathfinder R51 2004 2006 Armada TA60 2004 2006 Quest V42 2002 2006 Sentra B15 2003 2006 350Z Z33 2005 2006 Frontier D40 2003 2006 Murano Z50 IF YOU CONFIRM The MIL is ON with e DTC U1000 CAN COMM CIRCUIT OR e DTC U1010 CAN COMM 2006 Models only stored in the engine control unit and There are no drivability incidents DETERMINE IF This bulletin applies by performing steps 1 and 2 of the Service Procedure ACTIONS lf this bulletin applies there may be excess resistance in certain ground connections e Clean re tighten ECM ground connections e Clean re tighten negative battery cable body connection and battery post connection e f needed clean and ensure good contact between the steering member assembly and the left side instrument stay assembly IMPORTANT The purpose of ACTIONS above is to give you a quick idea of the work you w
3. iate Service Manual for additional diagnostic information 2 5 3 Make sure all ECM ground terminal connections are clean and tight as follows a Make a list of ground terminals for your vehicle Refer to the appropriate Service Manual section EC Power Supply and Ground Circuits ECM M80 F101 NOTE This is an example only Your vehicle may be different Ground Terminals ins Ge Zins TP060033 M78 a Figure 1 b Take your list and go to section PG in the appropriate Service Manual You ll be able to identify the exact location of the ECM ground terminals you ll need to check Ground terminal locations Example only nA LA MA Steering member assembly cross brace under dash TPO60035 3 5 c Now go to the ground terminal s on the vehicle and remove the nut or bolt that holds the terminal eyelet s d Clean the following surfaces on each ECM ground terminal This will ensure good contact in the connections e Both sides of the eyelet e Eyelet mounting surface NOTE Do not remove paint from painted surfaces in the engine compartment to improve ground Doing so may cause corrosion rust e Nut bolt threads e Female threads in bolt holes use the correct size tap e Reinstall and tighten the nut or bolt that holds the terminal eyelet 4 lf the ECM ground terminals are attached to the steering member assembly cross brace under the dash a Remove the fasteners nuts
4. ill be performing You MUST closely follow the entire Service Procedure starting on page 2 as it contains information that is essential to successfully completing the repair Nissan Bulletins are intended for use by qualified technicians not do it yourselfers Qualified technicians are properly trained individuals who have the equipment tools safety instruction and know how to do a job properly and safely NOTE If you believe that a described condition may apply to a particular vehicle DO NOT assume that it does See your Nissan dealer to determine if this applies to your vehicle 1 5 CLAIMS INFORMATION Submit a Primary Part PP type claim using the following claims coding Repair ECM Ground 1 EX12AA HD 42 0 6 hrs A33 Terminal 3 5 hrs A34 0 7 hrs A60 0 7 hrs TA60 2 2 hrs B15 QG QR 0 7 hrs D40 QR 0 8 hrs D40 VQ 2 5 hrs L31 0 9 hrs N50 0 8 hrs R51 0 6 hrs V42 0 7 hrs 233 1 Reference the FAST Parts Catalog and use the applicable Engine Control Unit P N as the PFP SERVICE PROCEDURE 1 Print the engine Freeze Frame FF data using CONSULT II e Refer to section EC in the appropriate Service Manual for Freeze Frame diagnostic information 2 Compare your printout to the chart below 58 F or 50 C a If your readings match exactly to the readings above go to step 3 b If your readings do not match exactly this bulletin does not apply e Go to section LAN in the appropr
Download Pdf Manuals
Related Search