Technical Service Bulletin
Contents
1. ne Select checking systems Select option d Medel Year C Unte2005MY Frem2006MY a The list on the left side of the screen will have all selections checked Do not change these selections DTCs may be set if the vehicle is equipped with options that are unchecked NOTE The list on the RH side of the screen appears for Outlander Sport RVR and Lancer based vehicles For those models the check mark at the bottom of the page is not highlighted inactive at this time If the check mark at the bottom of the screen is highlighted click it to proceed If not proceed to step e In the left column scroll to and click FAST IMMOB KEYLESS TPMS In the right column check the correct option code VF from the Loading Options Setup list This will activate the check mark at the bottom of the page e Vehicles with regular keyless entry buttons on a multi function key select VF2 e Vehicles with F A S T key select VFS In the left column scroll to and select METER A window will display Check the correct display type for the vehicle Click the check mark to continue A window will pop up asking you to confirm DTC erasing Click the check mark for DTC erasing and reading to begin When DTC erasing is completed a window will pop up lf DTCs return after reprogramming click the check mark to clear the window Diagnose and repair per the Service Manual If DTCs do not return click the ch2. MB991824 MUT III main harness A blue DLC connector MB991910 USB 2 0 cable MB991827 Engine Compartment Control Module label p n MSSF024G00 Reprogramming Database N11101 or higher e MEDIC 3 update at 085 or higher e Standalone MUT III laptop with Reprogramming CD 2 11 installed ECM REPROGRAMMING CHART MODEL DISPLAY ON MUT III AFTER MODEL YEAR 2010 CURRENT pata NO REPROGRAMMING PART NO TC Turbocharged New Part No Part No New New S W Part No Part No 10 Lancer Evolution 1860B306 1862B356 Waada Reset 4B11 TC 5M T 10 Lancer Evolution 1860B307 1862B443 1860B307 1860B30702 4B11 TC TC SST 10 Lancer Lancer Sportback 1860B308 1862B444 1860B308 1860B30802 CALF 4B11 D4 VVT TC TC SST 10 Lancer 1860B295 1862B421 1860B295 1860B29502 CALF 4B11 D4 VVT MT 10 Lancer 1860B296 1862B425 1860B296 1860B29602 CALF 4B11 D4 VVT CVT 10 Lancer 1860B297 1862B424 1860B297 1860B29702 FED 4B11 D4 VVT MT 10 Lancer 1860B298 1862B426 1860B298 1860B29802 FED 4B11 D4 VVT CVT 10 Lancer Lancer Sportback 1860B299 1862B427 1860B299 1860B29902 CALF 4B12 D4 VVT MT 10 Lancer Lancer Sportback 1860B301 1862B428 1860B301 1860B30102 FED 4B12 D4 VVT MT 10 Lancer Lancer Sportback 1860B300 1862B429 1860B300 1860B30002 CALF 4B12 D4 VVT CVT 10 Lancer Lancer Sportback 1860B302 1862B430 1860B302 1860B30202 FED 4B12 D4 VVT CVT 10 Outlander 1860B247 1862B422 1860B247 1860B24702 CALIF 2WD 4B12 D4 CVT 10
3. the check mark at the bottom of the page HSLDA nam j MFI should be highlighted as the default If not click on it to highlight it SZHLE Click on the check mark at the bottom of the page k A message will advise you that the system will Automatic search the data Click on the check mark to continue Feet A et leidet er 7 Page 10 of 13 TSB 12 13 002 W Peer don hinen G NEDICT word A MUST Ui Rae TY och D tersi 4 MEDIC EC M TO LAT EST VE R S IO N J TIR Techrical Informazon Retieval y MOL Matatiki Dasler Link Mitsubishi Spaga Service Tools SB con vehicle scan Too viewer CYAAGT 2000MY ECU Re Or M402001513C If an Complete Reprogramming message does not appear continue with step I If this message is displayed the ECM software is Gapi reprogramming already at the most current level Do not continue with ECU is areagy atthe latest fash evel fe Worm this reprogramming procedure This TSB does not acu Pen E 208086 S S W Pert No 1860805603 app y ABSASCSTCNSS Click the check mark to clear the window then click on a Q the Home icon at the lower left corner of the screen to return to the System Select main page a M Turn off the ignition switch and disconnect the MUT III Aisa 25 J Turn off and disconnect the battery charger Conduct dh MITSLEEAT ELECTRONIC DIAGNCSTIC AND DORMATI
4. 60B461 1860B46102 CALIF 4WD 4B12 D4 CVT Page 4 of 13 TSB 12 13 002 REPAIR PROCEDURE NOTE Reprogramming the ECM with the latest database i e 11101 includes all past and current reprogramming for TSBs of affected vehicles You do not need to reprogram the ECM for each TSB 1 Check the underside of the hood to verify there is no Authorized Modification label see page 13 for example previously installed to indicate this reprogramming has already been completed If a label is present and the ROM ID 7 on the label matches the New S W Part No in the table above the ECM is at the latest level and reprogramming is not necessary Conduct normal diagnosis for the subject DTCs For MEDIC 3 users only MUT III users go to step 5 Verify the MEDIC 3 is at version 3 1 and at update 085 or higher If your MEDIC 3 update is at least 085 continue with ME DIC 3 the Reprogramming Procedure on page 6 If your MEDIC 3 update is below 085 update your Version amp aa MEDIC 3 as follows Update m ee numbers Select the MEDIC 3 Admin tab and click on Updates za mm e ie mimm m Click Begin Drm 1 ut 1a 20N IL r Page 5 of 13 TSB 12 13 002 If the MEDIC update screen advises updates are available click the Begin button After all updates are complete GO TO THE REPROGRAMMING PROCEDURE ON PAGE 6 Standalone MUT III Scan Tool Viewer STV ONLY MEDIC 3 USERS go t
5. Engine Compartment All MSSF024G00 WARRANTY INFORMATION This bulletin is supplied as technical information only and is not an authorization to repair If an affected vehicle is reported with the described condition diagnose the condition repair as described in this bulletin and submit a normal warranty claim using the following information ECM Reprogramming for DTC P0016 or P0017 Nature Code 91Z Cause Code 605 Labor Operation No 138501 95 Time Allowance 0 3 hr Warranty Coverage Emissions Coverage Refer to the Superscreen for individual vehicle warranty coverage terms Special Warranty Information Normal warranty procedures apply
6. ON CENTER A D M29933 A SRILA COWMLOADI MDZ A MPD Rt c bob GLO M cse normal diag NOSIS l The Automatic Reprogramming CAN database screen will display Automatic Reprogramming CAN pou pre N11101 Pe see T m ncm ce rcm emn e Confirm the database number at the top right of the table is N11101 or higher pog e If more than one row is displayed in the table refer to the ECM Reprogramming Chart beginning on page 2 to select the proper Data No for this procedure and select the appropriate row 4r A gt gt Ma ENFXFEN Click on the correct row to highlight it Click on the check mark to continue m A message will ask you to Check reprogramming data n Click on the check mark to begin reprogramming Check reprogramming data It will take up to 5 minutes for reprogramming to Reprogram ECU OK complete nje ea 711 LL The Daytime Running Lights and both the engine and condenser fans will automatically be turned on during reprogramming Care should be taken to insure nothing gets caught in the moving blades The radio will be turned off and you will also hear a chime in the interior for a short period of time These are normal conditions Page 11 of 13 TSB 12 13 002 Psie Mames yumi jem gire ame Oui A EDG o This message will display when ECM a ey S UM ey E Sore ee reprogramming is successfully completed Confirm the New S W P N displ
7. Outlander 1860B303 1862B423 1860B303 1860B30301 CALIF 4WD 4B12 D4 CVT Page 3 of 13 TSB 12 13 002 MODEL DISPLAY ON MUT III AFTER MODEL YEAR 2011 ERE DATA NO REPROGRAMMING TC Turbocharged l New Part No New S W Part No 11 NAS Lancer Evolution 1860B474 1862B357 1860B474 1860B47403 4B11 TC 5M T 11 NAS Lancer Evolution 1860B475 1862B445 1860B475 1860B47503 4B11 TC TC SST 11 Lancer Lancer Sportback 1860B362 1862B419 1860B362 1860B36204 CALF 4B11 D4 VVT MT 11 Lancer Lancer Sportback 1860B363 1862B420 1860B363 1860B36304 CALF 4B11 D4 VVT CVT 11 Lancer Lancer Sportback 1860B364 1862B434 1860B364 1860B36403 FED 4B11 D4 VVT MT 11 Lancer Lancer Sportback 1860B365 1862B435 1860B365 1860B36504 FED 4B11 D4 VVT CVT 11 Lancer Lancer Sportback 1860B485 1862B446 1860B485 1860B48503 4B11 D4 VVT TC TC SST 11 Lancer Lancer Sportback 1860B456 1862B436 1860B456 1860B45602 CALF 4B12 D4 VVT MT 11 Lancer Lancer Sportback 1860B458 1862B437 1860B458 1860B45802 FED 4B12 D4 VVT MT 11 Lancer Lancer Sportback 1860B457 1862B438 1860B457 1860B45702 CALIF 4B12 D4 VVT CVT 11 Lancer Lancer Sportback 1860B459 1862B439 1860B459 1860B45902 FED 4B12 D4 VVT CVT 11 Outlander Sport RVR 1860B637 1862B418 1860B637 1860B63703 CALF 4B11 D4 CVT 11 Outlander Sport RVR 1860B665 1862B431 1860B665 1860B66502 FED 4B11 D4 MT 11 Outlander Sport RVR 1860B638 1862B432 1860B638 1860B63803 FED 4B11 D4 CVT 11 Outlander 1860B461 1862B433 18
8. Page 1 of 13 Technical Service Bulletin SUBJECT No TSB 12 13 002 ECM REPROGRAMMING FOR DTC P0016 or P0017 CRANKSHAFT CAMSHAFT POSITION MODEL See below CIRCULATE TO GENERAL MANAGER PARTS MANAGER X TECHNICIAN X SERVICE ADVISOR X SERVICE MANAGER X WARRANTY PROCESSOR SALES MANAGER This bulletin supercedes TSB 11 13 008REVII issued November 2011 to clarify REQUIRED PURPOSE Some affected vehicles may display an illuminated MIL with DTC P0016 Crankshaft Camshaft Intake Position or P0017 Crankshaft Camshaft Exhaust Position Sensor Phase Problem recorded in the ECM An incorrect parameter in the judgment criteria may cause mis detection of a fault without there being an abnormal condition This TSB provides dealers with a procedure to reprogram the ECM with new software to correct the condition IMPORTANT If an affected vehicle has a Malfunction Indicator Lamp MIL illuminated and DTCs other than those described above are listed in the ECM memory before reprogramming diagnose and repair those DTCs per the service manual before reprogramming DO NOT reprogram the ECM until the reason s for other DTCs being set is corrected AFFECTED VEHICLES 2010 2011 Lancer Evolution built before January 27 2011 2010 2011 Lancer Lancer Sportback RAE built before January 27 2011 2010 2011 Lancer Lancer Sportback built before January 27 2011 2010 2011 Outlander w 2 4L engine built before Janu
9. ary 27 2011 2011 Outlander Sport RVR built before January 27 2011 REQUIRED OPERATIONS OVERVIEW NOTE MIL illumination may return if ALL steps of this procedure are not performed 1 Confirm MUT III software contains the latest reprogramming database 2 HReprogram the ECM with new software per the Reprogramming Procedure 3 Reset the Timing Chain Learned Value as described in Group 00 General Timing Chain 4 Maintenance of the service manual 4 Perform Erase and Read All DTCs Perform a test drive to confirm DTCs do not return 6 Correct any fault found during diagnosis including a Remove the MIVEC oil control valve s and inspect for foreign material b Remove the valve cover and check if the timing chain is out of position on the sprocket For affected Lancer Evolution Lancer RAE and Lancer Sportback RAE vehicles only Pay special attention to visually check timing chain elongation stretch using procedures described g 4 4 Continued Copyright 2011 Mitsubishi Motors North America Inc 3849 Page 2 of 13 TSB 12 13 002 in Group 11A Engine Timing Chain Elongation visual check If the timing chain is stretched replace it and the oil pump chain using procedures described in Group 11A Engine of the service manual The following equipment is needed to reprogram the ECM MEDIC laptop computer with A C power adaptor 520924 or MIT547708 VCI Vehicle Communication Interface
10. ayed matches the table at the beginning of this TSB p You will be prompted to turn the ignition switch to Se tert rus up the OFF position wait at least 8 seconds then turn ca it back on q Click the check mark and you will be returned to the ECU Reprogramming page 2 Click the Home icon at the lower left corner of the page to return to the MUT III main page 3 Using the MUT III check and erase ALL DTCs from all systems as follows a Select Special Function Furbo i E b Eaters y UT CAN bus diagnosis Configuration Dec 2009 Introduction of stop sampling for Data tist Introduction of sampling rate for Dara list and Orire recorder function Introduction V C Stand alone Diagnosis Service Data z A MITSUBISHI ELECTRONIC DIAGNOSTIC AND INFORMATION CEN A O MASNA A IIRAL A DOWNLOAD MMS AMPA 86 9 05040 LGA up D vee i paa YET b Select All DTCS then select ERASE AND AL TR Techesesi inksemation Futteval D MDE Meses Dosier Uic at Mirb Special Sevice Tools MUTI Scan Tool Viewer 3 3 READ ALL DTCS y M 4 y Drive Recorder Display only DE Motiv iai Lm BEEN V C Stand alone Diagnosis Data Transfer to PC card MITSUBISHI ELECTRONIC DIAGNOSTIC AND INFORMATION CENT X 10 293320 JA 181930 A DOWNLOAD MAIS ACPI 5 9 50M OS dO inr Page 12 of 13 TSB 12 13 002 Erase and Read all DTCs Medel Year C Upte2005MY ze LI Ro
11. eck mark to clear the window and then click the Home icon in the lower left of the screen to return to the main menu Turn off the ignition switch and disconnect the MUT III Turn off and disconnect the battery charger Page 13 of 13 TSB 12 13 002 7 Using a ball point pen enter the appropriate Engine Control Module ECM part number Software lt q Part Number ROM ID this Technical Service Bulletin number TSB 12 13 002 your dealer code and the current date on the Engine Compartment Control Module Label p n MSSF024G00 The Vendor Code is not applicable The label is available from your facing PDC AUTHORIZED These Modifications Have P4 n Approved Bi AUTHORIZED MITSUBISHI MODIFICATIONS as Appropriate by EPA and MODIFICATION ITSUB b THE FOLLOWING MODIFICATIONS HAVISBREN MY DE PART NUMBER VENDOR CODE bd 9M ID Mc 1860830600 TSB S A T C3 AFER CODE DATE Engine Compartment Label The Control Module Label is NOT used for this reflash It should be discarded 8 Carefully remove all dirt and oil from a vacant area near the VECI label on the underside of the hood and affix the Engine Compartment Label LH side above to that area 9 Test drive the vehicle to confirm proper operation and that the MIL does not illuminate Diagnose and correct any DTCs that return Control Module Label PARTS INFORMATION Use only the Genuine Mitsubishi Parts listed below Description Model Part Number Label
12. nect the USB cable to the VCI When the laptop displays the MUT III main screen connect the USB cable to the laptop Connect the MUT III main harness with the blue DLC connection to the VCI Connect the blue connector of the MUT III main harness to the vehicle s data link connector Turn the VCI power switch ON Verify that the indicator lamp in the upper right corner of the screen is green DO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS INTERRUPTION DURING THE REPROGRAMMING PROCESS COULD CAUSE THE CONTROL UNIT TO LOSE DATA OR PREVENT FUTURE REPROGRAMMING IF THE USB CABLE IS DISCONNECTED DURING THIS PROCEDURE A WARNING MESSAGE WILL DISPLAY Page 7 of 13 TSB 12 13 002 ECM Reprogramming 1 Conduct the following steps to reprogram the ECM a Turn the ignition switch to the ON position If the vehicle is equipped with the F A S T System the transmitter must remain in the vehicle for the entire procedure UR alee ERU DNE EE UD GUN COE b If using MEDIC 3 from the main page click the o MUT III STV icon at the top center of the screen c Select Special Function System select Special function Introduction of fe stop sampling for Data tist Introduction of sampling rate for Dasa list and Drive recorder function MiEV Kilowam Voltage usage test Introduction V C J Stand alone Diagnosis Service Data d Select ECU reprogramming beer E apia y ic SWS monit Drive Recorder Dis
13. o the Programming Procedure on page 6 Verify that your MUT III has the most current version of the reprogramming database a From the MUT III Main Page Select Special Function Select ECU Reprogramming Select Database File Display CAN Confirm the database number displayed at the top right of the chart is N11101 If the database number displayed on your MUT III is N11101 or greater continue to the Reprogramming Procedure on page 6 If the database number displayed on your MUT III is lower than N11101 locate the Yellow MUT III Reflash CD 02 11 and follow the instructions on the CD label to update your MUT III Page 6 of 13 TSB 12 13 002 REPROGRAMMING PROCEDURE CONNECT A BATTERY CHARGER TO THE VEHICLES BATTERY DURING THE REPROGRAMMING PROCEDURE DO NOT ALLOW THE BATTERY CHARGER TO TIME OUT BATTERY VOLTAGE AS MEASURED AT THE BATTERY POSTS WITHOUT ELECTRICAL LOAD MUST BE KEPT AT 12 4V OR HIGHER IN ORDER TO REPROGRAM THE ECM MEASURE THE BATTERY VOLTAGE AND CHARGE AS NECESSARY USB CABLE VCI LAPTOP MEDIC II MUT III MAIN HARNESS MEDIC 3 MUT III LAPTOP Turn the laptop computer on If you re running on battery power and the charge indicator in the lower right hand corner of the screen does not show a full charge it is recommended that either the laptop battery be charged prior to beginning or that reprogramming be completed with the A C power adaptor connected to the laptop Con
14. play only Drive Reo jer Di md Sys V C I Stand alone Diagnosis Data Transfer to PC card e Select Automatic Reprogramming CAN ECU Repreg omm 14027001500 Moosa intent Explorer Automatic Reprogramming K line Automatic Reprogramming CAN Database File Display K line Database File Display CAN derer renie Reprogramming Data Selection Piease select toncton AS A MITSUBISHI ELECTRONIC DIAGNOSTIC AND INFORMATION CENI A I0 M299332M A 152022 A DOWMLOAD UMS A MCPD V 9 0500 SO xm Page 8 of 13 TSB 12 13 002 f Click on the car icon at the bottom of the page A 3 ie MET Ep EN JATCVTTC SST P DASTOWSS oom mede ed papa DK Dolor 1 pu SANT DESI POE pata Lo enee Dua oll oi enon L AEE LOTRO DGAGHOSTIC AMD MOATO CENTER Ex M i Lesa QA DOWALOMEMGM d MORD wee Wes A UDDO MEO TS WLS g If the VIN or vehicle description displayed does not match the vehicle you are working on click on the eraser icon at the bottom of the page Select VIN by clicking on the VIN button h Click on the icon in the lower RH corner of the screen to have MUT III automatically read the VIN If a message appears saying that the VIN cannot be input automatically manually type the 17 digit VIN into the VIN field at the top of the page Make sure the VIN is correct and click on the check mark Page 9 of 13 TSB 12 13 002 i Confirm that all data matches the vehicle and click
Download Pdf Manuals
Related Search