XX I-I Rev L0 (4.22.04)
Contents
1. re E Cut the notch 4 22 04 ee Le ee ae Ly oe a lisesi 1 2 3 4 5 MAXIMA Remove weather strip from right side of trunk opening Apply 150mm 6 of masking tape to the vertical edge of the gutter as illustrated in Fig 8 Measure 75mm 8 from weld seam at top right of gutter to the rear right of vehicle and mark position on masking tape with pen Fig 9 amp 10 Measure 15mm 5 8 from pen mark to rear of vehicle and mark position on masking tape with pen Fig 11 Measure 3mm 1 8 down from top edge of gutter lip and make a horizontal line connecting the two 2 pen marks This figure illustrates the area of material that will be removed using the die grinder Fig 11 N WARNING Use eye protection CAUTION Do not damage vehicle parts during notch cutting procedure Protect window and trim with fender cover or similar 6 Cut the notch with die grinder and cut off wheel 7 Remove masking tape 8 Remove burrs or sharp edges from the notch 9 Blow away metal chips and clean gutter and notch with 50 50 alcohol water solution 10 Apply rustproof compound to the cut surface of the notch 6 13 284 9798 00 LO MAXIMA 10 ANTENNA INSTALLATION a 1 If present remove PGF protective film from rear of the roof where antenna is to be mounted CAUTION In case of ambient temperatures below 20 Screw location degrees C 70 degrees F it i2. tie 7 Cut out antenna and tail outline and two square cable holes on antenna template Fig 16 Satellite antenna Line of the roof s roar exh 8 Carefully lift antenna from the roof do not pull out the wire that was just tucked and clean the area where the antenna is to be mounted with a 50 50 alcohol water solution Put antenna back on roof Center line of the antenna Center line of the UN CA UTI O N rear defogger Do not touch or contaminate the cleaned roof or adhesive tape on the antenna to prevent reduction of adhesive strength 9 Align template to vehicle centerline at bottom of template and the 2 square holes and roof edge Affix to vehicle with masking tape Use vertical defroster line for vehicle centerline Fig 16 10 Position antenna and tail in template and fine tune ieaiai tonicemnom alignment based on centerline of template Fig 16 11 Adjust the fore aft position of antenna such that antenna tail and roof have maximum contact surface with minimum gap at edge of roofline Fig 16 NG Antenna tail NG Antenna tail OK Antenna tail Roof Root Roof 12 Peel tape protector from rear of the antenna tail and lay down tail Fig 17 CAUTION Make sure antenna cable remains vertical under antenna tail flap Fig 18 4 22 04 8 13 284 9798 00 LO MAXIMA 13 Apply pressure along the length of the antenna tail to ensure proper adhesion 14 Peel tape protector from antenna and
3. 4 M4 screws Fig 2 2 Cut two 2 100mm by 30mm spacers from the double stick spacer item 5 in kit contents 3 Clean the back surface of the tuner with 50 50 alcohol water solution Attach the two 2 100mm by 30mm strips of double stick foam pad to bottom of tuner as shown Fig 3 4 Remove protective backing from foam pads and attach tuner to underside of package tray as shown Fig 4 5 Use 4mm 5 32 drill bit to drill holes through center hole on L brackets and secure tuner to package tray with two 2 5mm tapping screws 4 22 04 4 13 284 9798 00 LO MAXIMA Front of Vehicle 6 Insert antenna splitter cable connectors into corresponding tuner terminals 7 Clean the tuner with 50 50 alcohol water solution where the splitter is to be attached NOTE Ensure that the tuner surface is thoroughly cleaned before proceeding 8 Peel off the tape protector from the splitter Place the splitter on tuner and secure in position by applying force with hand pressure Fig 5 i TE i EN BUS Y a S wY J connector 9 Remove the tear tape to release the prewired N BUS cable Fig 6 10 Connect N Bus cable connector to the corresponding tuner terminal Fig 7 4 22 04 5 13 284 9798 00 LO 9 NOTCH CUTTING Wet ri a zy Pep an ie a hers See 2 2 on Bars aana EP aad gt nd aa ee ap ean Ps areas ae ett si oa n PF Eh 4 aa ti h Be he notch area aes sige spares ieee
4. apply 20 Ibs of downward force for 20 seconds while rocking hand back and forth across top of antenna to assure proper adhesion Fig 19 N CAUTION During antenna mounting process make sure rubber dust seal flares outward while downward force is applied 15 Remove template from vehicle N CAUTION Keep vehicle inside at least one hour after applying adhesive tape Avoid works imposing pressure on the adhered area including car wash within 48 hours 16 Route antenna cable down right side of rear window to the notch area Fig 20 amp 21 17 Use electrical tape to secure the antenna cable to vehicle near rear window Fig 20 CAUTION Do not apply too much tape as it could be visible after installation of the trim piece 18 Re install right rear window trim piece with 10mm Screw 19 Cut off 75mm of the corrugated tubing and slide remaining piece over antenna cable towards the base of the rear window 4 22 04 9 13 284 9798 00 LO MAXIMA 20 Starting 1 from right hand lower corner of window along wire affix four 4 cable clamps to gutter area towards notch as shown Final clamp should be located as close to edge of gutter on the furthest flat horizontal surface approximately 1 from notch Alternate the clamps while installing Fig 22 CAUTION Make sure corrugated tubing Is far enough away from gutter lip so it does not interfere with trunk weather strip Do not affix
5. GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1 DESCRIPTION SATELLITE RADIO SYSTEM 2 PART NUMBERS XM tuner kit 999U9 NV003 SIRIUS tuner kit 999U9 NV004 XM antenna kit 999U9 VQ006 SIRIUS antenna kit 999U9 VQ007 3 MODEL APPLICATION Maxima 2004 last 6 digits of VIN is 835089 or later 4 TUNER KIT CONTENTS Parts View 6 L Bracket 2 8 5mm Tapping Screw 4 9 GroundCable 1 CAUTION e This can be a difficult and time consuming installation that may require the skill of the master technician who is familiar with electronics installation Contact your regional DTS for additional information on installation support e Tuner unit antenna and antenna splitter must be same brand XM or SIRIUS e This is a universal installation kit so all parts may not be used e Re installation of satellite radio antenna to be performed by an authorized dealer only e In the event the satellite radio antenna or antenna splitter needs to be re installed do not use the Original mounting tape Order the low profile antenna tape remount kit 999U9 VQ010 e In the event the satellite radio antenna needs to be replaced order the appropriate Satellite Antenna Kit XM antenna 999U9 VQ012 SIRIUS antenna 999U9 VQ013 XM splitter 999U9 VQ004 SIRIUS splitter 999U9 VQ005 4 22 04 284 9798 00 LO MAXIMA 5 TOOL amp MATERIAL REQUIRED 1 Phillips screwdriver 8 Adhesive tape 2 Tape measure 9 Masking tape 3 Cl
6. cable clamp on sealant 21 Clean underside of the gutter where clear tape will be applied with 50 50 alcohol water solution then apply clear tape to prevent abrasion as shown Fig 23 NOTE The following steps 22 to 28 are critical to water leak therefore must be followed strictly 22 Place the edge protector over the notch 23 Use Alcohol wipe included in the kit to clean the surrounding area before application of clear tape 24 Route the antenna cable over the edge protector by laying the cable into the channel in the rubber CAUTION Make sure the antenna cable is seated in channel on both sides of the edge protector 25 Position the clear tape above the notch without peeling off the liner to estimate the correct position for the small amount of butyl gum 26 Before applying the clear tape apply a small amount of butyl gum to bottom side of antenna cable to hold the antenna cable at the radius corner where it will enter the clear tape 4 22 04 10 13 284 9798 00 LO Gutter side Clear tape o wrinkle 100 wet out Antenna cable 3 Clear tape D Edge protector 4 22 04 MAXIMA 27 Do not peel off the entire clear tape protector Pull the clear tape protector back 10mm 3 8 Then apply 10mm clear tape to the horizontal flat surface of the gutter Then slowly massage the clear tape with a PGF stick until you have reached the corners Make sure that the tape does not wrinkle Appl
7. ip remover 10 Drill with 4mm 5 32 bit equipped 4 Soapy water with1cm 1 2 stop 5 Flat file 11 Rustproof compound Bitumen Wax 6 50 50 alcohol water solution 999MP 9G001P or equivalent 7 Electrical tape e PGFstick for antenna cable routing e Die grinder with cutoff wheel eee wheel no larger than 3 diameter T 5 20mm Gei 6 INSTALLATION OUTLINE f ae h Antenna sphiter Y j B ee j SLAE i a Ne as ye f i Satellia anienna Tuner une SW ares E 7 VEHICLE PREPARATION 1 Using a PGF stick confirm that there is not an excessive amount of sealant under rear window molding at the area where the antenna cables will be installed DO NOT proceed to install radio if an excessive amount of sealant exists 2 Apply parking brake 3 Record the customer radio presets es S S S S 4 22 04 2 13 284 9798 00 LO MAXIMA 4 Make sure that the shift lever is engaged in the P position 5 Open the trunk lid 6 Turn the ignition switch OFF 7 Open engine hood 8 Disconnect the battery negative terminal to prevent short circuits during installation 9 Remove the following interior parts as shown in Fig 1 Refer to vehicle service manual e Trunk panel RH e Package tray lower trim cover Trunk side finisher RH Package Tray Lower Trim Cover 4 22 04 3 13 284 9798 00 LO 8 TUNER INSTALLATION MAXIMA 1 Attach two 2 L brackets to tuner with four
8. r trunk surfaces with five 5 pieces of sponge tape Fig 30 amp 31 34 Secure antenna loop to interior trunk panel with two 2 pieces of sponge tape Fig 31 4 22 04 12 13 284 9798 00 LO MAXIMA 11 OPERATION CHECK 1 Connect the battery negative terminal 2 Turn vehicle ignition switch to the ACC position 3 Turn radio on then select satellite radio mode Acquiring Sirius or loading XM will display for a while If not move vehicle to outside and try again 4 Tune to preview channel XM channel 1 SIRIUS channel 184 to make sure receiving preview channel correctly 5 Confirm proper audio operation AM FM TAPE CD 12 REINSTALLATION OF REMOVED PARTS 1 Re install all removed vehicle parts referring to the service manual for the vehicle 2 Clean interior of vehicle 13 FINAL INSPECTION 1 Inspect the vehicle interior and exterior for damage 2 Confirm proper operation of vehicle systems including moonroof if equipped 3 Reset radio presets to the recorded settings 4 If equipped reset the moonroof per service manual requirement 4 22 04 13 13 284 9798 00 LO
9. s required to warm the tape and mounting surface with a heater to a minimum of 20 degrees C 70 degrees F 2 Remove the 10mm screw securing window trim along right side of rear window and remove trim by pulling straight up Fig 12 3 Place the antenna on the roof in the approximate position it will be mounted This position will be on the center line of the vehicle use the rear window defroster vertical line as a reference Adjust the fore aft alignment of the antenna such that the small vertical portion of the antenna is contacting the rear edge of the roof while maintaining the smallest visible gap between the antenna tail and the edge of the root line 4 Unwrap antenna cable CAUTION e Do not let the antenna cable rest on floor it may be stepped on and damaged e Do not kink antenna cable 5 Route the antenna cable towards the passenger side of the vehicle as it exits the flexible portion of the tail Fig 13 6 Apply soapy water to antenna cable and window rubber molding and using a PGF stick tuck antenna cable underneath rubber molding to right side of window Fig 14 4 22 04 7 13 284 9798 00 LO MAXIMA PGE Stick e NOTE Metal window s PRS msl Insert the stick under the rubber molding Twist tt frame ear aN window Antenna Ab to make room under the rubber molding Place the kes ane ys T antenna cable under the rubber molding Rubber Reference Fig 15 molding gt ihG Ant
10. y the same technique to the vertical surface Then fold the tape over and apply the technique once more This should leave a smooth surface on all three sides Fig 24 amp 25 N CAUTION In order to stop water from entering the trunk through the clear tape the clear tape must have complete 100 wet out 5 10mm 1 4 3 8 on all three sides of peripheral boundary and no wrinkles Fig 25 Ensure antenna cable is entering the clear tape at the radius corner 28 Apply butyl gum at both ends of the clear tape The butyl gum should fit into both corners to cover the antenna cable and opposite end of clear tape Fig 24 N CAUTION Butyl gum must be placed across the cable for good water seal 29 Apply clear tape over the two 2 panel joints as illustrated to protect antenna cable Fig 26 30 Route antenna cable to tuner splitter location and secure to package tray with four 4 pieces of sponge tape Fig 27 amp 28 11 13 284 9798 00 LO MAXIMA 31 Leaving enough length for the splitter connection neatly coil excess antenna cable to create a loop 100mm 4 in diameter ZN CAUTION Do not kink the antenna cable 7 Ai 2 Do not change diameter of the antenna loop E sporo epe 32 Insert antenna terminal into corresponding splitter terminal Fig 29 33 Working from the tuner back towards the notch secure the antenna cable to the existing harness and or to vehicle interio
Download Pdf Manuals
Related Search