View Installation Instructions
Contents
1. HONDA Accessory Application Publications No VERSION 1 INSTRUCTIONS P N 08R04 T7S 100 PARTS LIST 8 Clips Left front door visor TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel Masking tape Ruler Soft towel Right front door visor INSTALLATION Left rear door visor Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers Right rear door visor NOTE e Visors may not be legal in all states Please check the laws of your state e These instructions show the left door visors being installed The same procedure applies to installing the right door visors 4 Brackets A e Be careful not to damage the paint finish and glass run Identification mark T7AA channels when installing the door visors e Handle the door visors with care They are not i designed to absorb shock or impact e This kit should be installed only if the ambient air p D temperature is 15 C 60 F or above w e To allow the adhesive to cure do not wash the vehicle for 24 hours Please advise your customer 4 Brackets B Identification mark T7AB 2015 American Honda Motor Co Inc All Rights Reserved All01797 20 1504 08R04 T7S 1000 90 1 of 7 Installing the Front Door2. DOOR SASH 11 Peel back the glass run channel in the areas shown 12 Install the brackets A and B between the door sash and the glass run channel at the measurements shown Seat the glass run channel properly around the brackets 2015 American Honda Motor Co Inc All Rights Reserved 13 14 2015 American Honda Motor Co Inc All Rights Reserved Using isopropyl alcohol on a shop towel thoroughly clean the area where the left rear door visor will attach Clean with isopropyl alcohol LEFT REAR DOOR QC72509AK Peel back the adhesive backings from each adhesive tape and tape the ends to the front surface of the left rear door visor with masking tape LEFT REAR DOOR VISOR 2 ADHESIVE BACKINGS a Peel back and tape them to the front surface of the left rear door visor MASKING TAPE QC72510AK All01797 20 1504 15 Align the clip holes in the left rear door visor with the bracket holes and install the clip while pushing up on each bracket There should be no gap between the bracket and the door sash NOTE Be extremely careful when installing the clips they cannot be reinstalled after installation LEFT REAR DOOR VISOR BRACKET A inside GLASS RUN CHANNEL SECTION VIEW BRACKET A BRACKET B x LEFT REAR N DOOR VISOR LAN Se inside 1 O SECTION Q VIEW Push up PROJECTION LEFT REAR DOOR VISOR up PROJECTION amp _ GLASS A RUN BRACK
3. E Be extremely careful when installing the i clips they cannot be reinstalled after installation DOOR SASH 2 mm 0 08 in LEFT FRONT DOOR VISOR inside GLASS RUN BRACKET B CHANNEL aa BRACKET A LEFT FRONT DOOR VISOR inside IO Sone SECTION SASH VIEW PROJECTION N BRACKET A LEFT FRONT X DOOR VISOR T Lo i A IA PROJECTION AAF LEFT FRONT DOOR QD51515AK 2 CLIPS LEFT FRONT DOOR 072505AK 2015 American Honda Motor Co Inc All Rights Reserved All01797 20 1504 3 of 7 8 While applying light pressure against the left front door visor carefully remove the adhesive backings in the order shown Use your finger to push up each bracket so there is no gap between the bracket and the door sash BRACKET B SECTION GLASS RUN VIEW 2 ADHESIVE BRACKET A BACKINGS Remove SECTION VIEW QC72507AK LEFT FRONT DOOR 9 Using a soft towel press and hold the left front door visor against the door sash for 30 seconds 4 of 7 All01797 20 1504 Installing the Rear Door Visors 10 Fully open the left rear door glass DOOR SASH BRACKET A SECTION BRACKET A VIEW GLASS RUN CHANNEL y Peel F i LP O YF BRACKET B DOOR SASH GLASS RUN CHANNEL X id SECTION VIEW sii BRACKET B gi GLASS RUN a CHANNEL _ BRACKET B BRACKET A ie id C EDGE OF QC72508BK DOOR SASH EDGE OF
4. ET aap CHANNEL AP 2 CLIPS LEFT REAR DOOR OC51AK 5 of 7 16 Align the left rear door visor to the position shown 17 DOOR EDGE OF SASH DOOR SASH 6 of 7 Align the door visor with the door sash 2mm 0 08 in FRONT VIEW LEFT REAR DOOR QD51516AK 18 19 All01797 20 1504 While applying light pressure against the left rear door visor carefully remove the adhesive backings in the order shown Use your finger to push up each bracket so there is no gap between the bracket and the door sash BRACKET B GLASS RUN GLASS RUN CHANNEL CHANNEL BRACKET A SECTION SECTION VIEW QC72513AK LEFT REAR DOOR 2 ADHESIVE BACKINGS Remove Using a soft towel press and hold the left rear door visor against the door sash for 30 seconds Repeat steps 1 through 18 to install the door visors on the right side of the vehicle 2015 American Honda Motor Co Inc All Rights Reserved CONFIRMATION AFTER INSTALLATION Restoration and Learning Operations 1 Start the engine 2 Using the power window switch repeat opening and close the window from half open to fully closed 10 times to allow the glass run channel to wear in The window should not bind 3 If necessary refer to the Service Manual to reset the power window If the automatic closing opening does not function after the reset reset again 4 If necessary refer to the Service Manual to carry out learning of the power w
5. Visors 1 2 of 7 Fully open the left front door glass GLASS RUN BRACKET A CHANNEL Peel SECTION DOOR SASH VIEW BRACKET A GLASS RUN CHANNEL BRACKET B SECTION GLASS RUN GLASS RUN 1 CHANNEL CHANNEL Peel 120 mm 4 72 in 80 mm 3 15 in x BRACKET B f BRACKET A Siaa EDGE OF DE DOOR SASH EDGE OF QC72502BK DOOR MIRROR BASE Peel back the glass run channel in the areas shown Install the brackets A and B between the door sash and the glass run channel at the measurements shown Seat the glass run channel properly around the brackets All01797 20 1504 Using isopropyl alcohol on a shop towel thoroughly clean the area where the left front door visor will attach Clean with isopropyl alcohol LEFT FRONT DOOR Qc72503Ak Peel back the adhesive backings from each adhesive tape and tape the ends to the front surface of the left front door visor with masking tape LEFT FRONT DOOR VISOR 2 ADHESIVE BACKINGS Peel back and tape them to the front surface of the left front door visor MASKING TAPE QC72504AK 2015 American Honda Motor Co Inc All Rights Reserved 6 Align the clip holes in the left front door visor with the 7 Align the left front door visor to the position shown bracket holes and install the clip while pushing up on each bracket There should be no gap between Align the door the bracket and the door sash visor with the NOT
6. indow If the automatic closing opening does not function after the learning carry out learning again NOTE The operations in the steps 3 and 4 should be done to all power windows having the automatic closing opening function to allow for proper functioning of the auto reverse function after installing the door visors USE AND CARE Clean the door visors with mild detergent and water Do not use organic solvents thinners benzine alcohol etc or cleaners containing any abrasive material 2015 American Honda Motor Co Inc All Rights Reserved All01797 20 1504 7 of 7
Download Pdf Manuals
Related Search