Home

Part# 69-3065

1. combinations larger than OE consider the additional stress you could be inducing on the OE and related components 4 Post suspension system vehicles may experience drive line vibrations Angles may require tuning slider on shaft may require replacement shafts may need to be lengthened or trued and U joints may need to be re placed 5 Secure and properly block vehicle prior to installation of ReadyLift Suspension Inc components Always wear safety glasses when using power tools 6 If installation is to be performed without a hoist ReadyLift Suspension Inc recommends rear alterations first 7 Due to payload options and initial ride height variances the amount of lift is a base figure Final ride height dimensions may vary in accordance to original vehicle attitude Always measure the attitude prior to beginning installation POST INSTALATION WARNINGS 1 Check all fasteners for proper torque Check to ensure for adequate clearance between all rotating mobile fixed and heated members Verify clearance between exhaust and brake lines fuel lines fuel tank floor boards and wiring harness Check steering gear for clearance Test and inspect brake system 2 Perform steering sweep to ensure front brake hoses have adequate slack and do not contact any rotating mobile or heated members Inspect rear brake hoses at full extension for adequate slack Failure to perform hose check replacement may result in component failure Longer replacement
2. R18 Bridgestone Dueler on 18x8 50 offset OE wh Vehicle Handling Warning Installation Warning Vehicles with larger wheels and tires will handle Always wear proper safety equipment and use the differently than stock vehicles correct tools when installing any suspension up grade Make sure vehicle is on a flat surface and Take time to familiarize yourself with the handling you are using jack stands or a lift rated for the of your vehicle weight of the vehicle Warning This ReadyLift 69 3065 Kit is designed and engineered to lift a stock ve hicle with no prior modifications The use of this kit along with items such as rear lift blocks or spacers add a leafs airbags suspension lifts body lifts or any other type of lifting accessory shall be done at the vehicle owners risk and will void any and all warranties in effect or implied by ReadyLift Revised ReadyLift Suspension Inc 12 30 08 3201 W MacArthur Bivd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972
3. RIENDA J5 SUSPENSION INC ReadyLift Part 69 3065 2002 2008 Chevy Trailblazer GMC Envoy Installation Instructions SAFETY WARNING ReadyLift Suspension Inc recommends this system be installed by a professional techni cian In addition to these instructions professional knowledge of disassembly reassembly procedures and post installation checks must be known PRODUCT SAFETY WARNING Modifying your vehicle ride height may result in the vehicle handling differ ently than a factory equipped vehicle Extreme care must be used to prevent loss of control or vehicle rollover Failure to drive your modified vehicle safely may result in serious injury or death ReadyLift Suspension Inc does not recommend the combined use of suspension lifts body lifts or other lifting devices You should never operate your modified vehicle under the influence of alcohol or drugs Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions Always wear your seat belt Pre Installation Notes 1 Special literature required OE Service Manual for model year of vehicle Refer to manual for proper disas sembly reassembly procedures of OE and related components 2 Adhere to recommendations when replacement fasteners retainers and keepers are called out in the OE manual 3 Larger rim and tire combinations may increase leverage on suspension steering and related components When selecting
4. disconnect the ABS line from the support bracket on the ReadyLift Part 69 3065 2002 2008 Chevy Trailblazer GMC Envoy Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any installation instruction updates Installation by a trained mechanic is recommended Use a pitman arm puller of similar tool to break the taper If not available you can use a hammer to free the taper by strik ing the lower strut mount while pry kti ma a Liv r t gt h Strike here ae Nad AN eo ae 1M J i 4 ae R the t trut ti isand th Use a ball joint separator or other appropriate tool to break the ball Shela ie ace ede ea a cena joint loose from the upper control arm If tool is unavailable to you strut Support the lower control arm with a jack Unbolt and taper can be freed by striking the upper control arm with a hammer remove the upper ball joint retaining bolt Lower the jack Place the lower strut mount in a vise Install the ReadyLitt strut extension using the factory nuts Tighten to 42 ft lbs Loosen but do not remove the strut arm pinch bolt This allow this strut to rotate around for reinstallation Revised ReadyLift Suspension Inc 12 30 08 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 SUSPENSION INC ReadyLift Part 69 3065 2002 2008 Chevy Trailblazer GMC Envoy Installation Instruc
5. hoses if needed can be pur chased from a local parts supplier 3 Perform head light check and adjustment 4 Re torque all fasteners after 500 miles Always inspect fasteners and components during routine servicing Revised ReadyLift Suspension Inc 12 30 08 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 ReadyLift Part 6 69 9 3065 2002 2008 Chevy Trailblazer GMC Envoy Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any installation instruction updates Installation by a trained mechanic is recommended Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground Use aminimum 3 ton jack stands and place under frame for safety or a 2 two post lift if available Make sure that the emergency brake is on and the rear wheels are blocked to prevent a rollout Bill of Materials Description Steel strut extensions Front M10 serrated flange nuts Aluminum button shaped coil spacers Rear Remove the front wheels Starting on the fel side discon nect the ABS line from the support bracket at the knuckle upper control arm mm Loosen but do not remove the two upper strut mounting nuts Unbolt the lower sway bar end link ReadyLift Suspension Inc 3201 W MacArthur Blivd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Also
6. oroughly and completely before beginning installation Check www Readylift com for any installation instruction updates Installation by a trained mechanic is recommended REAR INSTALLATION Position truck on a flat surface and lift vehi cle by the frame so that the rear wheels are off the ground Use a minimum 3 ton jack stands and place under frame for safety or a 2 two post lift if available Make sure that the emergency brake is on and the front wheels are blocked to prevent a rollout Remove the rear wheels Unclip the ABS Line from the frame rail on both sides Use a jack to support the rear axle Lower the jack enough to remove the coil spring and isolator Take the isolator and install it into the ReadyLift coil spacer ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 RIENDA S J SUSPENSION INC ReadyLift Part 69 3065 2002 2008 Chevy Trailblazer GMC Envoy Installation Instructions The ReadyLift coil will mount on top of the coil Raise the jack and reconnect the rear shock Tighten to 55 ft lb Repeat steps 17 22 on opposite side Install the upper sway bay end links and tighten to 74 ft lbs Press the ABS line clip back into the frame rail on both sides Install the factory wheels and tires and lower the vehicle to the ground Be sure to double check that all hardware is to proper torque Re torque all hardware after 500 miles 23 Lo
7. tions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any installation instruction updates Installation by a trained mechanic is recommended Install the strut into the OEM location The Readylift kit has three mounting studs that locate into the existing holes in the strut tower Loosely install the upper strut mounting nuts a a s Raise the jack to compress the suspension Reconnect the upper ball joint to the upper control arm Insert the retaining bolt and nut tighten to 42 ft lbs Lower the jack and install the lower strut mount and nut but do not tighten Tighten the strut arm pinch bolt Reinstall the lower sway bar end link Tighten the upper strut mounting nuts to 42 ft lbs Tighten the lower sway bar end link nut to 74 ft lbs Reconnect the ABS line at the knuckle and the upper control arm Repeat steps 1 13 on opposite side When completed install the factory wheels and tires and lower vehicle to the ground Bounce the front of the vehicle to settle the suspension Tighten the lower strut mount nut to 175 ft lbs Double check all hardware for 44 Proper torque Re torque all hardware after 500 miles ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 ReadyLift Part 69 3065 2002 2008 Chevy Trailblazer GMC Envoy Installation Instructions Please read instructions th
8. wer jack enough to reinstall the factory coil with the Ready Lift soacer on top of it Wheel and Tire Fitment Due to the design of the front suspension wheel spacers may be needed clear larger tires on the OE wheel This may also apply to aftermarket wheel and tire combinations Also because of the unique 6 on 5 bolt pattern there are only a limited number of aftermarket wheels available for this vehicle You can purchase wheel adapters from Fred Goeske at www wheeladapter com and change the bolt pat tern to the more common 6 on 5 5 bolt pattern ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Revised 12 30 08 SUSPENSION INC ReadyLift Part 69 3065 2002 2008 Chevy Trailblazer GMC Envoy Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any installation instruction updates Installation by a trained mechanic is recommended Wheel Alignment a Certified Alignment Technician that is experienced with lifted vehicles is recom mended to perform the alignment It is recommended that you have your vehicle s alignment checked whenever installing suspension parts i Fa U a Per oe i sn AILA i aT is ans es At ae tae Oh Oy Pho ig Caan FA AR PETU OA N TREN es ua L Vielh v eel w 1 5 wheel spacers After ReadyLift SST Lift Kit 69 3065 255 70

Part# 69-3065

Contents

Download Pdf Manuals

Related Search

Related Contents