Please click here for the ISFM2201 owners manual (Rel.2.0)
Contents
1. Installation Visual Installation Diagram Yellow Wire 12 V Connect this wire to the vehicle s 12 V CONSTANT power supply In this situation use the standard 6 pin connector with the basic 3 wire harness when connecting the unit to the vehicle s electrical system when ready to power up the unit simply join the male and female ends of these connectors Monici s with Standard Analog Steering Wheel contents The ISFM2201 module features an integrated adaptive steering wheel interface SWI allowing the device to interact with the steering wheel controls in standard analog stereo control systems without the need for any additional adapters or converters Once properly connected the SWI interface can be configured specifically for that vehicle using the module s integrated learning mode feature a No need to cut or strip any wires 12V pun on the primary harness simple to remove and or replace the unit GND should the need arise Ignore the Black Wire GND s hna and gray wires all together This wire should be connected to the stereo s GROUND terminal or the vehicle chassis ACE Vehicles Equipt with Digital CAN BUS Steering Wheel Control Systems If the vehicle in which the ISFM2201 module is to be installed uses digital steering wheel control signals an adapter will be required to decipher and translate the digital signals coming from2. gested that this process be completed by a certified installation specialist Ensure that the vehicle is running during the following procedures Using Learning Mode Before proceeding ensure that the vehicle s ignition is in the off position and that the vehi cle s electrical system has completely powered down The ACC or switched 12 V accessory wire coming from the hide away module s wiring harness should have no voltage applied Set DIP Switch Positions for Learning Mode In order to initiate learning mode during vehicle power up DIP switches number 1 and 3 must be set towards the down position while switches 2 and 4 should be set to up position Start the Vehicle and Wait to Enter Learning Mode Once the DIP switches are in the proper positions start the vehicle The hide away module should turn on and proceed to enter learning mode after a period of approxi mately 10 15 seconds Make sure that none of the vehicle s steering wheel stereo con trols are activated until the appropriate cues are received failure to do so may cause mal functions or result incorrectly calibrated controls To confirm that the ISFM2201 module is indeed in learning mode you ll need to check the LED status indicator The green status LED provides important visual cues during the learning process It is visible through the small square hole located near the center of the metal enclosures largest face on the opposite side from the product
3. CAN BUS MS CANA ON sata 9 USCA TVS TAO DIR 10 Configuration BEC TOS i giae ee eeesrurer erate tare coma ere aren eich trent a terme erste ver anne etre Mae ee ee ee erence eer eee 11 A PP Tee o E N E eee 11 AOUN T AOE a a 11 also ge Mersld gli gio MOTO ose ES errr ee aes ee ae eee eee 12 PASER MOdulE SEUD eren R 12 Operation SNG US SAM ai va 13 COMtromAg Your Mone DEVICE asenna a e a E E 14 PANGS TCE Calera ti is 14 HEAR Ei A A E E serene 15 Waranty Mona ON scai EA een pes ene dec eke 16 Introduction oo Precautions Please take some time to carefully read these instructions before proceeding Failure to follow instructions could result in improper operation or electrical shock Neither AAMP of America Apple Inc nor Google Inc its regional offices distributors or resellers take any responsibility for any damage or injury resulting from the installation and subsequent use of this Bluetooth eyes free integration kit e Do not open disassemble and or alter the interface in any way e Do not insert anything into the device s casing Doing so could result in electric shock or damage to sensitive electronic components e Always ensure that any connections A have been made properly e Only operate unit when it is safe to do so Avoid using your mobile device when travelling at high speeds or ask passengers to operate it for you e Do not allow the use any of this product s features distract you from driving e
4. female antenna connector Then connect the male antenna connector to the standard antenna port on the back the the factory radio Vehicles not equipped with a standard motorola antenna connector will require a set of standard and reverse antenna adapters specific to that vehicle Hands Free Mini Microphone The included auxiallary wired mini microphone is required for proper operation of hands free calling and Voice Recognition VR features It connects directly to the ISFM2201 hide away module unit via a common 3 5mm audio jack Configuration a Before You Start The unique placement and color of the steering wheel control signal wires will often vary in accordance with each vehicles make and model therefore it is imperative that all previous installation procedures have been completed correctly and carefully incomplete and or improper installation will very likely cause errors during the learning process as well as inviting possible malfunctions unin tended operation and potentially even total module failure Once confirming that all necessary connections between the ISFM2201 hide away module and the installation vehicle have been made properly the system needs to be programmed to work with that vehicle s unique steering wheel stereo control signals The Steering Wheel Interface SWI is calibrated using the module s intuitive learning mode function a quick and easy one time interactive process that must be complete
5. label If you tune the radio to 98 1FM you can hear audio cues as well When ready to begin SWI learning procedures the LED Should illuminate solid Red and continue Begin Learning Mode Sequence After confirming a solid red status LED the module is in learning mode waiting for the user to perform the first of a series of specific steering wheel button presses five in all The last of these learned controls will be designated for activating and deactivating the ISFM2201 module as well as performing some of the more important Bluetooth commands When possible it is recommended that your vehicle s mode button be chosen to perform this function however due to the technical limitations of certain vehicle makes and models these specific recommended configurations may not be possible Due to configuration inconsistencies that may arise between installations this guide will also refer to each of the control buttons as Bl B2 and B3 respectively The learning sequence requires the programmer to press hold and release B2 Ch then B3 Ch then volume up then volume down then B1 mode To complete the sequence The red status LED will provide cues and feedback during the learning process With that in mind you should identify the controls you intend to designate as B1 B2 and B3 briefly familiarize yourself with the following sequence and prepare to begin the learning process 1 Press B2 CH With the solid red LED il
6. national or international laws Made for iPod Made for iPhone and Made for iPad mean that an electronic accessory has been designed to connect specifically to iPod iPhone or iPad respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod iPhone or iPad may affect wireless performance iPad iPhone and iPod are trademarks of Apple Inc registered in the U S and other countries The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3 0 Attribution License Android is a trademark of Google Inc NOTICE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AND INDUSTRY CANADA LICENSE EXEMPT RSS STANDARD S OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DE VICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION
7. Exercise good judgment and keep your eyes on the road at all times e Do not expose unit to extreme temperatures humidity or shock A e Keep the module and any mobile devices away from fluids e Keep away from children this device may contain small parts which could become loose if broken or disassembled or as a result of excessive vibration and heat exposure Small components and packaging materials may present a choking hazard when handled by young children Introduction About the Hardware The ISFM2201 Bluetooth integration kit includes everything necessary to successfully complete standard analog vehicle installation procedures Prior to doing so please verify that each of the following components are accounted for Included Components ISFM2201 Hide Away Module Simple This small metal enclosure is discretely tied into the vehicles existing radio system During installation it should be hidden inside the vehicle s dash or radio compartment The DIP switches located on the side of the module are used to change certain settings during the configuration procedures The included microphone will be connected to the hide away unit using this 3 5mm audio jack Mini Microphone The wired mini microphone connects to the hide away module and allows for custom placement providing crystal clear sound when using hands free or voice recognition features Wiring Harness 2 Pieces The p
8. Licensed Application Any attempt to do so is a violation of the rights of the Application Provider and its licensors If You breach this restriction You may be subject to prosecution and damages The terms of the license will govern any upgrades provided by Application Provider that replace and or supplement the original Product unless such upgrade is accompanied by a separate license in which case the terms of that license will govern b Consent to Use of Data You agree that Application Provider may collect and use technical data and related information including but not limited to technical information about Your device system and application software and peripherals that is gathered periodically to facilitate the provision of software updates product support and other services to You if any related to the Licensed Application Application Provider may use this information as long as it is in a form that does not personally identify You to improve its products or to provide services or technologies to You c Termination The license is effective until terminated by You or Application Provider Your rights under this license will terminate automatically without notice from the Application Provider if You fail to comply with any term s of this license Upon termination of the license You shall cease all use of the Licensed Application and destroy all copies full or partial of the Licensed Application d Services Third Party Materials
9. The Licensed Application may enable access to Application Provider s and third party services and web sites collectively and individually Services Use of the Services may require Internet access and that You accept additional terms of service You understand that by using any of the Services You may encounter content that may be deemed offensive indecent or objectionable which content may or may not be identified as having explicit language and that the results of any search or entering of a particular URL may automatically and unintentionally generate links or references to objectionable material Nevertheless You agree to use the Services at Your sole risk and that the Application Provider shall not have any liability to You for content that may be found to be offensive indecent or objectionable Certain Services may display include or make available content data information applications or materials from third parties Third Party Materials or provide links to certain third party web sites By using the Services You acknowledge and agree that the Application Provider is not responsible for examining or evaluating the content accuracy completeness timeliness validity copyright compliance legality decency quality or any other aspect of such Third Party Materials or web sites The Application Provider does not warrant or endorse and does not assume and will not have any liability or responsibility to You or any other person for
10. the InSeam application users can manually select and save the specific FM frequency desired for Bluetooth audio use Additionally for safety purposes the InSeam app for Android provides users the option to inhibit SMS text notifications appearing on the factory radio RDS display anytime the vehicle s speed exceeds a pre defined value To learn more on how to use the specific features of this application consult the operation section of this guide Downloading InSeam Prior to installation and configuration please download and install the InSeam Application on the Bluetooth enabled iOS or Android in Seam powered device intended for use in your eee a vehicle The InSeam o Ao be y Google play downloaded free of z charge from Google s E Available on ina Android Marketplace or App Store Apple s OS AppStore ES Pre Installation Vehicle Compatibility Considerations Before attempting to install this product you should review the following installation considerations to determine whether your vehicle will require any additional adapters to successfully complete the installation process Analog vs Digital Controls You will need to determine whether your particular make and model of vehicle equipped with steering wheel stereo controls operates using analog or digital control signal systems Vehicles equipped with digital CAN BUS based systems will require the additional PASER CAN BUS integration mo
11. wheel White Black Wire Connect this wire to the portion of the steering wheel control wire 2 originating from the vehicle s head unit Pink Black Wire Connect this wire to the portion of the steering wheel control wire 2 leading to the steering wheel Connect to a Power Source On the vehicle s wiring harness you will need to identify and tap into a constant accessory power and ground wire Once the correct wires have been located connect the corresponding portions of the new wiring harness included with this kit Yellow Wire Connect this wire to the vehicle s constant 12V power source Red Wire Connect this wire to the vehicles switched 12V or accessory source Black Wire Connect this wire to the vehicles ground GND wire or the chassis itself Connect the Antenna Inputs Outputs Take the antenna plug previously disconnected from the rear of the head unit and plug that into the female antenna connector protruding from the hide away module The hide away unit s remaining male connector should be plugged into the antenna port on the rear of your head unit Optional AUX RCA Connection An alternative audio feed is available via the stereo RCA connectors on the wiring harness This option can be used if you wish to relay the audio through an available AUX input rather than through the FM radio The RDS display notification feature will not work if the module is connected this way rather than thro
12. BOVE EXCLUSION AND LIMITATIONS MAY NOT APPLY TO YOU f Limitation of Liability TO THE EXTENT NOT PROHIBITED BY LAW IN NO EVENT SHALL APPLICATION PROVIDER BE LIABLE FOR PERSONAL INJURY OR ANY INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF PROFITS LOSS OF DATA BUSINESS INTERRUPTION OR ANY OTHER COMMERCIAL DAMAGES OR LOSSES ARISING OUT OF OR RELATED TO YOUR USE OR INABILITY TO USE THE LICENSED APPLICATION HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY CONTRACT TORT OR OTHERWISE AND EVEN IF APPLICATION PROVIDER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF LIABILITY FOR PERSONAL INJURY OR OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THIS LIMITATION MAY NOT APPLY TO YOU In no event shall Application Provider s total liability to you for all damages other than as may be required by applicable law in cases involving personal injury exceed the amount of fifty dollars 50 00 The foregoing limitations will apply even if the above stated remedy fails of its essential purpose g You may not use or otherwise export or re export the Licensed Application except as authorized by United States law and the laws of the jurisdiction in which the Licensed Application was obtained In particular but without limitation the Licensed Application may not be exported or re exported a into any U S embargoed countries or b to any
13. CY AND EFFORT IS WITH YOU TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THE LICENSED APPLICATION AND ANY SERVICES PERFORMED OR PROVIDED BY THE LICENSED APPLICATION SERVICES ARE PROVIDED AS IS AND AS AVAILABLE WITH ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND AND APPLICATION PROVIDER HEREBY DISCLAIMS ALL WARRANTIES AND CONDITIONS WITH RESPECT TO THE LICENSED APPLICATION AND ANY SERVICES EITHER EXPRESS IMPLIED OR STATUTORY INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES AND OR CONDITIONS OF MERCHANTABILITY OF SATISFACTORY QUALITY OF FITNESS FOR A PARTICULAR PURPOSE OF ACCURACY OF QUIET ENJOYMENT AND NON INFRINGEMENT OF THIRD PARTY RIGHTS APPLICATION PROVIDER DOES NOT WARRANT AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE LICENSED APPLICATION THAT THE FUNCTIONS CONTAINED IN OR SERVICES PERFORMED OR PROVIDED BY THE LICENSED APPLICATION WILL MEET YOUR REQUIREMENTS THAT THE OPERATION OF THE LICENSED APPLICATION OR SERVICES WILL BE UNINTERRUPTED OR ERROR FREE OR THAT DEFECTS IN THE LICENSED APPLICATION OR SERVICES WILL BE CORRECTED NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY APPLICATION PROVIDER OR ITS AUTHORIZED REPRESENTATIVE SHALL CREATE A WARRANTY SHOULD THE LICENSED APPLICATION OR SERVICES PROVE DEFECTIVE YOU ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON APPLICABLE STATUTORY RIGHTS OF A CONSUMER SO THE A
14. any third party Services Third Party Materials or web sites or for any other materials products or services of third parties Third Party Materials and links to other web sites are provided solely as a convenience to You Location data provided by any Services is for basic navigational purposes only and is not intended to be relied upon in situations where precise location information is needed or where erroneous inaccurate or incomplete location data may lead to death personal injury property or environmental damage Neither the Application Provider nor any of its content providers guarantees the availability accuracy completeness reliability or timeliness of stock information or location data displayed by any Services You agree that any Services contain proprietary content information and material that is protected by applicable intellectual property and other laws including but not limited to copyright and that You will not use such proprietary content information or materials in any way whatsoever except for permitted use of the Services No portion of the Services may be reproduced in any form or by any means You agree not to modify rent lease loan sell distribute or create derivative works based on the Services in any manner and You shall not exploit the Services in any unauthorized way whatsoever including but not limited to by trespass or burdening network capacity You further agree not to use the Services in any manner to ha
15. d the previously solid red LED on the module will turn off Continue to hold the current button for a few seconds Once the learning process has been successfully completed all three LEDS will illuminate solid Red Blue Green If all LEDs are not solid repeat the programming process from the beginning Return DIP Switches to Default Position and Cycle Power Once the learning process has been completed successfully be sure to return all switches to the default up position It is vital that you remember to return the DIP switches back to the up position otherwise the module will initiate learning mode again the next time the vehicle is started and the previous configuration values will be erased or overwritten Cycle the vehicles power off and back on again for normal InSeam operation PASER Module Set Up When using the PASER module the aforementioned configuration procedures are unnecessary as the pre programmed PASER module will automatically configure itself according to the vehicle in which it has been installed LED Status Indicator In the center of one side of the black rectangular PASER module there is a small circular LED status indicator When the PASER module is properly connected and receiving power this status LED will illuminate solid green Anytime the PASER module detects a Signal initiated from the steering wheel controls the status LED will momentarily change from green to orange when the control i
16. d successfully prior to initial use Users are discouraged from attempting the initial configuration themselves rather the qualified installation specialist performing the earlier hardware installation should configure and test the SWI interface upon finalizing the job doing so will save the customer and or end user time and frustration DIP Switch Settings The positions of the DIP switches located on the side of the hide away module determine what mode the unit will enter upon power up Locate the DIP switch port a small opening on one of the longer sides of the rectangular metal enclosure through which a small row of four DIP switches should be visible These switches are labeled 1 4 read left to right when the enclosure s label is facing upward and the LED indicator light is facing downward Default Learning Mode Be extremely careful when changing the dip switch configuration as selecting the incorrect switches could cause undesired operation About Learning Mode Successful completion of this initial configura tion learning process will require easy access to the vehicle s steering wheel control buttons switches as well as the ISFM2201 hide away module itself Using a specific sequence of timed button switch presses learning mode allows the hide away module to read and store the unique electrical signals generated by each button and or switch on the corresponding vehicle s steering wheel It is strongly sug
17. dule designed to provide Plug n Play compatibility with the primary ISFM2201 module Once the hide away module has been properly installed and configured it s various functions are initiated remotely using the OEM steering wheel controls Once active all the device s Bluetooth functions are controlled using timed presses of 3 pre selected buttons referred to by this guide as B1 B2 or B3 Product functionality is essentially identical in both analog resistive and digital CAN BUS environments however activation deactivation procedures as well as button assignments will vary accordingly Antenna Connector Type Either physically inspect the back the vehicle s head unit or consult the proper service manual to determine what type of antenna connector is used in that specific stereo system If the vehicle s stock antenna is connected to the factory head unit using anything other than a standard Motorola automotive antenna connector like the one pictured to the right then it may not be directly compatible with the connectors protruding from the ISFM2201 hide away module If the vehicle s factory antenna is not compatible you will need to obtain both standard and reverse antenna adapters specific to your vehicle s stock antenna connector to properly com plete the installation Installation a Before You Start Make sure that the vehicle s ignition is off and all of the electronics have been powered down befo
18. e improper installation or alteration of this product All parts of this iSimple product are guaranteed for a period of 1 year as follows Within the first 12 months from date of purchase subject to the conditions above iSimple will repair or replace the product at our discretion if it is defective in material or workmanship providing it is returned to an Authorized Simple dealer with PROOF OF PURCHASE from an authorized iSimple dealer Warning This equipment may be reset by unintentional electrostatic discharge during operation Exposure to direct sunlight or extreme heat may cause damage or malfunction FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re or
19. ices are capable of forwarding SMS notifications using the Bluetooth RDS feature Currently this product does not offer support for SMS text message notifications via RDS on OS devices however support for compatible OS devices should be available through future firmware releases Music Info When a connected mobile device is being used to stream music to the vehicle s stereo details such as song title artist or album are relayed to the vehicle stereo s RDS display Each time the track changes the RDS readout should update with the new song s relevant information Warranty Information One Year Limited Warranty The quality controls used in the manufacture of this product will ensure your satisfaction This warranty applies only to the original purchaser of this product from an authorized iSimple dealer This warranty covers any supplied or manufactured parts of this product that upon inspection by iSimple authorized personnel is found to have failed in normal use due to defects in material or workmanship This warranty does not apply to installation expenses Attempting to service or modify this unit operating this unit under conditions other than the recommended voltage will render this WARRANTY VOID Unless otherwise prescribed by law iSimple shall not be liable for any personal injury prop erty damage and or any incidental or consequential damages of any kind including water damage resulting from malfunctions defects misus
20. ientate or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that of which the receiver is connected Consult the dealer or an experienced radio television technical for help WARNING You are responsible for taking appropriate caution when operating a motor vehicle The vehicle driver should maintain their attention on the road at all times You agree to use this product in compliance with these instructions terms of use and all federal and state laws DISCLAIMER Under no circumstance shall the manufacturer or the distributor of the ISFM2201 be liability for any claims losses or damages associated with use of the ISFM2201 in connection with a motor vehicle in noncompliance with these instructions terms of use warnings or any misuse of the product The manufacturer s and distributor s sole liability associated with the sale and use of the ISFM2201 is the replacement of the product END USER LICENSE AGREEMENT This End User License Agreement License Agreement is between You and AAMP of Florida Inc AAMP d b a AAMP of America Inc Application Provider By downloading the mobile application Licensed Application you agree to be bound by all terms of this License Agreement WARNING You are responsible for taking appropriate caution when operating a motor vehicle The vehicle driver should maintain their a
21. initiate your connected mobile device s voice dialing or VR function RDS Text Display With a compatible mobile device actively connected the ISFM2201 module in conjunction with the InSeam application allows vehicle radios equipped with RDS text readouts to display custom information such as caller ID SMS text messages and music info right on the vehicle s stereo display By relaying this information to the vehicle s entertainment system via RDS users can safely see who s calling or texting or what song is playing without distracting the driver Not all devices support this feature Caller ID When a call is received on a connected mobile device the caller id information is transmitted through the vehicles radio system using the RDS protocol allowing compatible vehicles to display the name and or number of the caller right on your vehicle s stereo system display Phonebook profile transmission via RDS is not supported by all devices SMS Text Messages When a SMS text message is received on a connected Android mobile device any notifications generated can be relayed to the stereo display for easy reading To ensure driver safety the InSeam application installed on a connected mobile device can be used to implement speed limit safety restrictions designed to disable transmission of any SMS notifications via RDS anytime the vehicle s current speed exceeds a pre determined value Note Not all mobile dev
22. is may vary based on vehicle compatibility or how the device was configured during installation therefore this guide will refer to these controls as buttons B1 B2 and B3 Activating Deactivating Bluetooth Functions To activate the ISFM2201 unit s transmitting function and i engage the steering wheel AA control interface press and hold y NE the button corresponding to B1 on your vehicle s steering wheel for approximately 1 2 seconds Similarly if the unit is acacia already active and or Bifor 1 2 sec functioning it can be r deactivated by pressing and Bluetooth audio holding the same B1 button functions switch for the same extended duration of time While active the 3 specific stereo control buttons switches mapped during the programming process are repurposed for Bluetooth function control Any additional unmapped unused steering wheel stereo controls will likely cease to function until the unit is de activated at which time they revert to standard stereo control functions until the unit is activated once more D AAA Hands Free Calling With the ISFM2201 in active mode you can control your mobile device s hands free calling functions directly from your steering wheel controls allowing users to make answer end and reject calls on their mobile device without taking their hands off the wheel The specific hands free functions provided through steering wheel controls are as follows Y Initiate V
23. luminated press and hold the button intended for B2 usually CH or up arrow The red LED should turn off upon activating that control Continue to hold the button until you see the solid red LED re illuminate then release the current button and prepare to move on to the next step B3 2 Press B3 CH With a solid red LED press and hold the button intended for B3 usually CH or down arrow The status LED should turn off when pressed Like before continue to hold the current button for a few seconds until the red LED re illuminates then release that button and prepare for the next step volume up 3 Press Volume Up With the solid red LED illuminated once again press and hold the up button Like before the red LED should turn off upon activating that control Continue to hold the button until you see the solid red LED re illuminate then release the current button and prepare to move on to the next step volume down ES Configuration 4 Press Volume Down With the solid red LED illuminated once again press and hold the volume down button Like before the red LED should turn off upon activating that control Continue to hold the button until you see the solid red LED re illuminate then release the current button and prepare to move on to the next step mode button 5 Press B1 Mode With the solid red LED illuminated once again press and hold the button intended for B1 usually labeled mode When first presse
24. m allows the user to open any application installed on their smartphone by simply pushing a button on the steering wheel then saying the name of the application aloud the commands depend on the VR application chosen by the user Additionally using compatible Bluetooth mobile devices it is now possible to hear the text messages on the car audio system see them on the radio s RDS display feed and even reply all by voice no need to touch the device You can even launch and control Navigation features using voice recognition all with verbal confirmation and audio prompts InSeam has also integrated parental controls safety features available on android devices To avoid driver distractions parents can configure the system disable notifications SMS text messages via the RDS display if the vehicle s current speed exceeds a preset speed limit ES Table of Contents Introduction PrECAUION Sracurestrrse iento Rita 4 ADOQUE Me ae 19 6 Wat llas 5 laa Es a e 5 Optional FASER CAIN BS Ad A ss ese eects cca encarta eee eae A 5 ADOULTNE SOT WV ANC eseni reana R ata 6 Pre Installation Vence COMpatubllty CONSI ETA AS sosen S e Fi ANAIS Vve Digia CONTOS A EEA 7 ARENA CONNECCION TYPE ra 7 Installation BEIO TO A e A E E E A EA E IA 8 ANOT RESIST SOUS EAU OT T a ape E cll ache lca cat 8 CORMECE The SCSI Wheel Contro WIES earnan ccs csc cess reste deas eect edad Ue edee edad eee eee ces 8 CONNEC C WIN O HANES S pai ino 8 QI AT
25. oice Dialing Briefly press B1 to initiate the connected device s voice dialing or VR function Accept Incoming Call When ringing press and hold B2 fora moment to answer the incoming call Reject Incoming Call When ringing press and hold B3 for about a second to reject or cancel the call End Current Call To disconnect a call in progress press and hold B3 for about a second UA a Streaming Music If a paired mobile device is already playing music upon first starting your vehicle the ISFM2201 will automatically enter streaming music mode and begin transmitting the audio signal through your vehicle s radio on the designated FM station Music streaming may also be initiated from the steering wheel Using the vehicle s steering wheel controls operators can change tracks pause play or stop the music on a paired iOS or Android mobile device The corresponding buttons switches are as follows Play Pause Press and hold B2 for a moment PPI Skip Forward Briefly press B2 Stop Press and hold B3 for about a second 044 Skip Backwards Briefly press B3 Using Voice Recognition VR Applications Using the steering wheel control functions user s can remotely launch their preferred VR application on their mobile device The extent of the VR capabilities available depend upon the specific application being used on the mobile device Initiate VR Application Briefly press B1 to
26. one on the U S Treasury Department s list of Specially Designated Nationals or the U S Department of Commerce Denied Person s List or Entity List By using the Licensed Application you represent and warrant that you are not located in any such country or on any such list You also agree that you will not use these products for any purposes prohibited by United States law including without limitation the development design manufacture or production of nuclear missiles or chemical or biological weapons h The Licensed Application and related documentation are Commercial Items as that term is defined at 48 C F R 2 101 consisting of Commercial Computer Software and Commercial Computer Software Documentation as such terms are used in 48 C F R 12 212 or 48 C F R 227 7202 as applicable Consistent with 48 C F R 12 212 or 48 C F R 227 7202 1 through 227 7202 4 as applicable the Commercial Com puter Software and Commercial Computer Software Documentation are being licensed to U S Government end users a only as Commercial Items and b with only those rights as are granted to all other end users pursuant to the terms and conditions herein Unpublished rights re served under the copyright laws of the United States i The laws of the State of Florida excluding its conflicts of law rules govern this license and your use of the Licensed Application Your use of the Licensed Application may also be subject to other local state
27. rass abuse stalk threaten defame or otherwise infringe or violate the rights of any other party and that the Application Provider is not in any way responsible for any such use by You nor for any harassing threatening defamatory offensive or illegal messages or transmissions that You may receive as a result of using any of the Services In addition third party Services and Third Party Materials that may be accessed from displayed on or linked to from the mobile device are not available in all languages or in all countries The Application Provider makes no representation that such Services and Materials are appropriate or available for use in any particular location To the extent You choose to access such Services or Materials You do so at Your own initiative and are responsible for compliance with any applicable laws including but not limited to applicable local laws The Application Provider and its licensors reserve the right to change suspend remove or disable access to any Services at any time without notice In no event will the Application Provider be liable for the removal of or disabling of access to any such Services The Application Provider may also impose limits on the use of or access to certain Services in any case and without notice or liability e NO WARRANTY YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT USE OF THE LICENSED APPLICATION IS AT YOUR SOLE RISK AND THAT THE ENTIRE RISK AS TO SATISFACTORY QUALITY PERFORMANCE ACCURA
28. re you attempt to make any connections Applying voltage to the incorrect wires while working could damage to the hide away module or your vehicles electrical system Remove amp Disconnect the Head Unit Obtain the stereo removal instructions specific to your vehicle and proceed accordingly Once the head unit has been successfully removed and the necessary wiring and antenna connectors have been detached you may proceed with the installation procedures specific to your vehicle s needs Analog Resistive Control Installation These installation instructions apply only to vehicles that use analog resistive steering wheel control systems If your vehicle uses a digital CAN BUS control system the installation process will use a different wiring harness provided with the PASER adapter in that case please refer to the Digital CAN BUS Control Installation section on the next page Connect the Steering Wheel Control Wire s Consult vehicle wiring instructions to determine the SWC wires that will be used during the installation of ISFM2201 Once the correct wires have been identified you will need to cut these wires and connect their two ends to the corresponding wires on the harness provided White Red Wire Connect this wire to the portion of the steering wheel control wire 1 originating from the vehicle s head unit Pink Wire Connect this wire to the portion of the steering wheel control wire 1 Leading to the steering
29. reless there should no be no interference or distortion resulting from overcrowded frequencies and other common sources of FM interference Clear Paired Devices Selecting this option will result in all previously paired configured device profiles to be deleted from the stored list of previously paired devices Any previously paired mobile devices will no longer auto connect to the module using any of these devices again requires repeating the initial pairing process just like connecting a new device for the first time Controlling Your Mobile Device Using the Steering Wheel Controls The ISFM2201 allows for convenient control of your Bluetooth enabled OS or Android mobile device simply by using the factory steering wheel stereo controls already installed in your vehicle When engaged the ISFM2201 steering wheel control interface is designed to take control of three of the vehicle s steering wheel stereo control buttons redirecting these inputs to control specific functions on the operator s paired mobile OS or Android device Using simple timed presses of these buttons operators can control their music launch voice recognition applications and initiate hands free calling functions all from the steering wheel In most cases the 3 buttons used to control your mobile device s Bluetooth functions should correspond to the Mode Ch and Ch controls on your steering wheel This is the recommended configuration however th
30. rovided wiring harnesses used for standard analog installation procedures It is connected to the vehicle s power supply as well as the steering wheel stereo control wires located behind the head unit or in the steering column Vehicles employing digital CAN BUS control systems will use a different type of harness Optional PASER CAN BUS Adapter In vehicles equipped with steering wheel stereo controls employing the digital CAN BUS system the PASER add on module is required for proper control integration PASER Module Sold Separately CFOO40UNAP11 Universal SWC interface for AAMP bluetooth handsfree kits CE ERN E 3 110 R 03 1146 00 FYPO40UNAPO1 Made in Italy This accessory works in conjunction with the ISFM2201 module allowing it to translate and filter the more complex digital command signals generated by the vehicle s steering wheel controls Introduction oo About the Software To properly control and configure the ISFM2201 you will need to download and install the required Inseam application on the OS or Android powered mobile device you intend to use You can download the latest version of the InSeam app for free from either the Google Play Marketplace or the Apple App Store The InSeam App The InSeam mobile application works in conjunction with the ISFM2201 hide away unit providing end users a simple utility through which certain basic operation settings can be configured and stored From within
31. s released the LED should revert to green once more AAA a Using InSeam App Upon launching the application users are presented witha main menu screen with multiple features from which to select MAIN MENU Device Settings User guide simple InSeam Selecting this icon will simply redirect the user from the InSeam main menu to their mobile device s Bluetooth connection utility usually accessible via the devices system preferences as well Settings Devices Settings User guide Learn more Selecting this icon will bring up the InSeam settings menu from which users can configure a variety of operational parameters and activate safety features If no ISFM2201 device is detected a warning reading InSeam Not Connected will overshadow the normal menu SETTINGS ta YY Module Name AE Settings If desired users can reprogram their module s name to something more unique Customizing SMS Y the name of your specific ISFM2201 module can help to better identify and differentiate it from any other devices potentially transmitting in the vehicle s vicinity SMS Text Notifications Android only The notifications field allows users to implement safety restrictions limiting the RDS text notification feature according to pre determined speed limit values In RDS capable vehicles the InSeam application provides the ability to forward SMS text Notifications Disable af
32. simple Installation amp Operation Manual Manuel d installation et d op ration EYES FREE BLUETOOTH MEDIA VEHICLE INTEGRATION KIT KIT D INTEGRATION DE VEHICULE DE MEDIA D EYES FREE BLUETOOTH ISFM2201 ES Bluetooth ye oN Made for _ _ qa BliPod JiPhone LliPad 253015 Note to Readers The information contained within the following documentation is subject to change without notice Features discussed therein may be revised and or updated to reflect mobile device compatibility fixes as well as firmware revisions To ensure that you have the most recent version of the product documentation please download the PDF file from the product support section of www iSimpleSolutions com or consult the User Manual section of the InSeam application installed on a compatible mobile device Rev 2 01 Congratulations On Your Purchase Thank you for choosing the simple ISFM2201 for use with the InSeam App as your mobile media and hands free integration solution The ISFM2201 is designed to provide the connecting link between your Bluetooth enabled Apple OS or Android powered device and your vehicle InSeam is not a simple car kit but goes far beyond the hands free or streaming audio by allowing the user to fully pilot their smartphone or Tablet via Voice Recognition VR InSeam is fully integrated into the vehicle steering wheel control buttons providing a seamless transition between radio mode and smartphone mode InSea
33. ter 30 v mph Button Configuration Frequency 98 1 Mhz notifications to the vehicle entertainment system s RDS text display for safer and more convenient access to incoming SMS messages When the SMS notification speed limit restriction is active the module will automatically disable the RDS SMS notification feature anytime the vehicle s current speed exceed the predetermined threshold To activate this feature use the speed limit pull down menu to select the cut off value desired After the desired value has been selected touch the icon to the right of the text reading SMS located just above your selected speed limit value Set Frequency Selecting this icon will bring up a FM frequency selection list towards the bottom of the display The ISFM2201 and InSeam app require the use of your vehicle s FM radio tuner to function properly The ISFM2201 uses FM modulation to re transmit incoming Bluetooth audio signals through your vehicles OEM entertainment system The ISFM2201 module s default FM transmission frequency should be set to 98 1MHz however should the need arise users may customize the device to transmit on alternative FM stations Simply choose the desired FM frequency value on the list presented and then press select to confirm your choice and save the new custom FM value The list of available FM frequencies ranges from 88 0MHz to 108 0MHz and because module uses wired FM modulation as opposed to wi
34. the steering wheel controls Digital CAN BUS Installation When the ISFM2201 module is used in conjunction with the PASER CAN BUS translator the PASER unit is wired directly into the vehicle s electrical system instead of the ISFM2201 module Rather the ISFM2201 Red Wire ACC IGN This wire should be connected to the car stereo s ACC IGN wire or a switched 12 volt power source 1 ACCAGN _ 2 Ground 60 3T erav consone a sra e Paser module receives power through it s E connection to the PASER unit GND 12V Auxillary RCA Outputs i ACC If neccessary the audio signal being transmitted No A by the ISFM2201 can be accessed via these stereo RCA connectors N Pink Wire White Red Wire Connect this wire to the portion of Connect this wire to the portion of the the steering wheel control wire 1 steering wheel control wire 1 originating leading to the steering wheel from the head unit 5V Control Line GROUND GROUND C e s 5V Control Line White Black Wire Pink Black Wire Connect this wire to the portion of the Connect this wire to the portion of _ _ steering wheel control wire 2 originating the steering wheel control wire 2 from the head unit leading to the steering wheel Male amp Female Antenna Cables Connect the vehicle s factory antenna to the cable with the
35. ther than through the FM radio or if the device is being paired with an specialized aftermarket system The RDS display notification feature will not work if the module is connected this way rather than through the antenna cables Connect ISFM2201 Module to the Wiring Harness With all previous steps completed connect the wiring harness s 16 pin connector to the metal enclosure via corresponding the port on the end opposite the antenna cables ES Installation LED Indicators On the bottom of the InSeam housing there is a small hole and a tri color LED status indicator The LED colors will illuminate to indicate the current mode of the InSeam module Blinking Red The module is in connectable mode waiting for the most recently paired device to reconnect Blinking Green The module is actively connected to a paired mobile device and ready for operation via the steering wheel controls Alternating Red and Green The module is in discoverable mode awaiting a Bluetooth equipped mobile device to initiate pairing Continuous Solid Red The module is in learning mode set using the dipswitches The LED will illuminate solid Red until a SWC button is pressed to learn its value Continuous Solid Red Green Blue This indicates that all the SWC values have been successfully learned in the learning mode All LEDs off When the module is actively connected and streaming audio none of the LEDs will be illuminated
36. ttention on the road at all times You agree to use the Licensed Application in compliance with this License Agreement and all federal and state laws a Scope of License The Licensed Application is licensed not sold to You for use only under the terms of this License Agreement Application Provider reserves all rights not expressly granted to You This license granted to You for the Licensed Application by Application Provider is limited to a non transferable license to use the Licensed Application on any mobile device that You own or control and subject to any rules set forth by the app store from which the Licensed Application was downloaded This license does not allow You to use the Licensed Application on any mobile device that You do not own or control and You may not distribute or make the Licensed Application available over a network where it could be used by multiple devices at the same time You may not rent lease lend sell redistribute or sublicense the Licensed Application You may not copy except as expressly permitted by this license and the Usage Rules decompile reverse engineer disassemble attempt to derive the source code of modify or create derivative works of the Licensed Application any updates or any part thereof except as and only to the extent any foregoing restriction is prohibited by applicable law or to the extent as may be permitted by the licensing terms governing use of any open sourced components included with the
37. ugh the antenna cables Connect ISFM2201 Module to the Wiring Harness With all previous steps completed connect the wiring harness s 16 pin connector to the metal enclosure via corresponding the port on the end opposite the antenna cables Digital CAN BUS Control Installation These installation instructions apply only to vehicles equipped with digital CAN BUS control systems No cutting or splicing will be necessary Connect the Wiring Harness Upon purchasing the PASER module you will be provided with a easy connect Y harness specific to the vehicle in which the device is being installed All you have to do is connect one end to the back of the radio and the other to the original radio harness disconnected previously Once the corresponding connections have been made the module will have access to the vehicles power source as well as the digital control lines for the steering wheel stereo controls Connect the Antenna Inputs Outputs Take the antenna plug previously disconnected from the rear of the head unit and plug that into the female antenna connector protruding from the hide away module The hide away unit s remaining male connector should be plugged into the antenna port on the rear of your head unit Optional AUX RCA Connection An alternative audio feed is available via the stereo RCA connectors on the wiring harness This option can be used if you wish to relay the audio through an available AUX input ra
Download Pdf Manuals
Related Search