INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
Contents
1. slide the door glass into the closed position and hold in place with either a saddle cup assembly painter tape or a wedge STEP 12 Disconnect the window lift motor connector STEP 13 Using a 10 mm socket and ratchet assembly remove the three 3 window it motor retaining screws 742 124 INSTALL REMOVALINSTRUCTIONS WINDOW REGULATOR aon er ppc ha mara yur hea inspec oven pom er e prt yoa de renra see arte act ar tr uneerde ta et ere fe ues Fy pa eap Tanon sn ramno rece he Sep nania hani ma on a ouch STEP 14 Remove the window regulator through the main access hole NOTE You may need to remove the Styrofoam noise insulator from the door STEP 15 Using a 10mm socket and ratchet assembly or a T 30 Torx bit remove the three GB window Ift motor retaining screws INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR a senor to inon sv marno racine Sepa ad nein dante aa T Installation Instructions STEP 1 Using a 10mm socket and ratchet assembly or a T 30 Torx bit attach the three 3 window lift motor retaining screws to the window regulator STEP 1a Install the window regulator through the main access hole STEP 2 Using a 10 mm socket and ratchet assembly attach the four 4 window regulatorinterior door trim panel support bracket retaining screws INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR a rarer mara e2. INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR aon ir pene ha ral yur hea inspec oven pom er e prt oa do renra eran oar a warnings iode E op mal Rendon a ene coca ny PA REMOVAL INSTALL OF WINDOW REGULATOR 742 124 Buick Century 1997 2005 Chevrolet impala 2003 05 Buick Regal 1997 2004 Pontiac Grand Prix 1997 2003 Oldsmobile Intrigue 1998 2002 Tools required for removal and installation of window regulator and motor assembly Silicone spray lubricant Trim panel removal tool Plc Saddle cup assembly tape or wedge to hold window in place Flat blade screwdriver or plastic pry tool Tomm socket or driver Phillips screwdriver Grease pencil or marker T30Torxbit INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR aon ier sgpenaeh raran for yoa hea curam pece oven praedare er e prt yoa do renra enn al on warns edhe pra hand ow otc ae T T Removal Instruct STEP 1 Using a pick or small fat blade screwdriver remove the interior door pull taining screw cover plate STEP 2 Using a 10mm socket and ratchet assembly remove the two 2 interior door pl retaining screws STEP 3 Using a trim panel removal tool remove the interior door trim panel assembly NOTE Place the trim panel temoval tool between the interior door tim panel and the door Pry the tool toward You to release the interior door tim p
3. anel retaining clips INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR aon ier pene hay mara for yoa who ouam pece oven procure a prt oa do rera AE aon ma mamno nce separa fea ma ion deante aay T T Pre STEP 4 Disconnect the power switch assembly STEP 5 Remove the interior door trim panel STEP 6 Remove the water vapor barrier INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR aon spent ha ral yur hea inspec oven pom er e prt oa do rera senor to anon swung penae e Sepa ad snow dante aa T T STEP 7 Using aT 30 Torx bitand ratchet assembly remove the Torx bit retaining the interior door trim panel support bracket STEP 8 Temporarily connect the power switch assembly and lower the door glass exposing the screws attaching the window regulator to the door glass STEP 9 Using a 10 mm socket and ratchet assembly remove the four 4 interior door wim panel support bracket retaining screws NOTE The four 4 interior door trim panel support bracket retaining screws also hold the window regulator in place INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR i eer need STEP 10 Disconnect the power switch assembly STEP 102 Using a 10mm socket and ratchet assembly remove the two 2 screws attaching the window regulator to the door glass STEP 11 Once the door glass has been separated from the window regulator manually
4. c el prt ne nena yo seh ear ct tes ec a A ennai ane sn warngs ned ee sop mal Red an Klon d cebu ety E STEP 3 Using a 10mm socket and ratchet assembly attach the three 3 window lift motor attaching screws STEP 4 Connect the window Ift motor connector STEP 5 Temporarily connect the power switch assembly to raise or lower the window regulator aligning the points mounting the door glass to the window regulator STEP 6 Manually slide the door glass into position aligning the points attaching the door lass to the window regulator STEP 6a Using a 10mm socket and ratchet assembly attach the door glass to the window regulator NOTE If you did not remove the Styrofoam noise insulator please go to Step 8 STEP 7 Instali the Styrofoam noise insulator INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR aon ire pena ha ral for yoa hea inspec oven praedare er e prt yoa de rera enn lon warns edhe sep nana hand ow seta ana T T STEP 6 Attach the water vapor barrier STEP 9 Connect the power switch assembly connector STEP 10 Install the interior door trim panel assembly NOTE Be sure to align all of the interior door trim panel retainers Failure to do so may result in damage to the interior door trim panel or the interior door trim panel retaining clips 742 124 INSTALL REMOVALINSTRUCTIONS WINDOW REGULATOR aon ier appear yu
5. r hea coram pece oven poms er e prt yoa do renra AE danan m namng nse he sep nania fen ma ion deante aay T STEP 11 Using a 10 mm socket and ratchet assembly attach the two 2 interior door pull retaining screws STEP 12 Install the interior door pull retaining screw cover plate ae T STEP 13 Verify that the interior door trim panel is secured and that the window regulator is operating propery We appreciate your opinions regarding this product Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product 1 800 523 2492
Download Pdf Manuals
Related Search