RC939 Instructions
Contents
1. d damages exceeding the cost of the product e sealed lamps and or lamp bulbs LED s and batteries f the finish on any portion of the product such as surface and or weathering as this is considered normal wear and tear g transit damage initial installation costs removal costs or reinstallation costs INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN TIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES ALL IMPLIED WARRANTIES IN CLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU This warranty service is available by either a returning the product to the dealer from whom the unit was purchased or b completing a warranty claim online at www intermatic com This warranty is made by Intermatic Incorporated Customer Service 7777 Winn Rd Spring Grove Illinois 60081 9698 For warranty service go to http www Intermatic com or call 815 675 7000 INTERMATIC INCORPORATED Spring Grove Illinois 60081 9698 www intermatic com 158 01244 RE2. pump or light ON OFF This document provides setup and operation instructions for the RC939 radio transmitter Carefully follow these instructions to setup the RC939 transmitter Then perform the operation instructions as needed NOTE The transmitter must be within 6 feet of the receiver during the setup INITIAL SETUP Follow the procedures below to complete the initial setup for the transmitter Figure 1 RC939 Radio Transmitter Verifying Receiver Operation Before setting the transmitter perform this procedure to verify that the RC613L RC613R receiver is operating properly 1 Press the red button on the receiver The connected pump or light will turn ON to indicate the receiver is working 2 If the pump or light does not turn ON make sure the receiver has power and then retest Press one of Linking RC939 Transmitter Button with the RC613 Receiver Sie ce 1 With a stylus or paper clip press the program button on the side of the transmitter until the red LED illuminates See Figure 2 for location of button and LED 2 On the receiver press the CODE SET button The adjacent LED illuminates See Figure 3 3 Press a button on the transmitter multiple times until the LED on the receiver turns OFF This is the button that will control the receiver 4 Press one of the other buttons on the transmitter that was not configured The red LED on the transmitter shuts OFF The transmitter is now linked to the receiver en 5 Pr
3. NTERMNMATIC INSTALLATION RC SERIES OPERATION amp REMOTE CONTROLS SERVICE MANUAL Model RC939 THREE CHANNEL RADIO TRANSMITTER For indoor and outdoor use suitable for Pool Spa equipment control E BATTERY TYPE 3 Volt CR2032 Coin Battery Risk of Injury or Property Damage e Always keep remote controls out of reach of children NEVER permit children to operate or play with remote controls e Never allow small children to play with batteries If battery is swallowed immediately notify doctor NENII Risk of Fire Explosion or Chemical Burn e Replace ONLY with 3 Volt CR2032 coin battery e DO NOT recharge disassemble heat above 212 F 100 C or incinerate NOTICE To comply with FCC and or Industry Canada rules IC adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to comply with FCC Standards for Home or office use Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may Cause undesired operation DESCRIPTION The RC939 Radio Transmitter is used to control a pump or light In order for the transmitter to work it must be linked to a RC613L RC613R receiver that receives the ON OFF command from the transmitter and then turns the connected device
4. VB
5. ess the configured button on the transmitter to verify it communicates with the receiver and turns the connected device ON OFF 6 Repeat steps 1 through 5 to link an other program button to another receiver CODE SET ON OFF Figure 3 RC613R Receiver Linking Multiple transmitters with a Receiver Up to three different transmitters can control a receiver Follow steps 1 through 4 of Linking each RC939 transmitter with the RC613 receiver OPERATION The transmitter settings configured at Initial Setup can be adjusted as needed Perform the applicable instructions below to operate the transmitter and adjust a setting in the transmitter NOTE The usable operation range for the transmitter is 100 Feet How to Use the Radio Transmitter Once you setup the required links between the transmitter s and receiver s you are ready to use the transmitter Press the configured button on the transmitter to turn the connected device ON OFF Excluding a Transmitter Button Link from a Receiver Follow this procedure to exclude a transmitter button from a receiver 1 With a stylus or paper clip press the button on the side of the transmitter until the red LED illuminates NOTE See Figure 2 for location of button and LED 2 Press the configured ON OFF button on the transmitter that you want to exclude from the receiver 3 Press one of the other buttons on the transmitter The red LED on the transmitter turns OFF 4 Press the b
6. utton you want to exclude to verify it does not control the receiver The button is excluded Deleting All Codes from a Receiver To delete all codes from a receiver press and hold the Code Set button until the LED shuts off All the codes are deleted from the receiver and all links CODE SET between the transmitter s and the receiver are deleted CODE SET Button Changing the Transmitter Battery ON OFF YIntermatic Follow this procedure to remove or change the transmitter battery 1 Insert a wide flat screwdriver into the slot on the side of the transmitter and remove the cover 2 Replace the CR2032 lithium coin type battery inside the transmitter NOTE Make sure the new battery s terminal is facing away from the circuit board on the transmitter 3 Snap the cover onto the transmitter Figure 4 Figure 5 Removing transmitter cover LIMITED ONE YEAR WARRANTY If within the warranty period specified this product fails due to a defect in material or workmanship Intermatic Incorporated will repair or replace it at its sole option free of charge This war ranty is extended to the original household purchaser only and is not transferable This warranty does not apply to a damage to units caused by accident dropping or abuse in handling acts of God or any negligent use b units which have been subject to unauthorized repair opened taken apart or otherwise modified c units not used in accordance with instructions
Download Pdf Manuals
Related Search