"Premium Kiddie Rides" Operation and Service Manual
Contents
1. oa A _ Coin Holder y f 4 Configure the control box according to following instructions and picture 1 Open the panel of control box with key 2 Turn on the electric switch on the control box and make sure the LED light is shining 3 Set the price from 1 3 coins by the COUNT knob 4 Set the time from 1 3 minutes by the TIMER knob 5 Adjust the volume by the VOLUME knob 6 Switch off the machine for 10 seconds and then restart the machine THIS STEP IS VERY IMPORTANT OTHERWISE YOUR CONFIGURATION WILL NOT TAKE EFFECT 7 Close and lock up the panel of control box After inserting coin coins the machine will give out alarm sound and then rock with music according to the time set previously and will give out alarm sound again 3 seconds before game over When suspend the operation of machine please switch off the machine 4 Attentions q 2 Please make sure th ground line is connected well when the machine is in use When machines can not work or stop automatically please switch off the machine immediately and examine amp repair the machine 5 Maintenance 1 2 When machine is dirty you can lean it with cotton fabric In order to protect the machines please lubricate the main moving parts of the machine termly You d better lubricate the rocking shafts and bearings every 2 month and lubricate other parts in every 6 months After a period of use the str2. User Manual of Advanced Kiddie Rides for Single Support and Multi Support Kiddy Rides E BIZ2CNINA LIMITED W ww pandavending com Tel 0086 21 52926646 Fax 0086 21 52950439 Please read this lt User Manual gt carefully before operating machines User Manual of Kiddie Rides 1 Technical Parameters Item Value Remark Working Voltage AC220V or on your request Machine Working Current lt 2 4A Motor Power 180W Rocking Frequency 0 58 0 75S Carrying Capacity 40KGS 2 Applicability Place indoor and apply to 3 7 years old children under 40Kgs 3 Configuration and Operation 1 2 Connect the machine to electrical outlet with plug Open the panel of control box with key and turn on the electric switch on the control box Please make sure the indicial LED light inside the switch is shining Configure coin acceptor according to followirig instructions and picture Open the panel of coin acceptor with key and take out the coin acceptor Put the mode switch on N O Normal Open Put the speed switch on MEDIUM 45ms medium pulse signal w N Mount a coin to be used into the coin holder according to the below picture Adjust the sensitivity knob it s a small knob marked as VR on the coin acceptor until the coin acceptor car accept the right coins correctly and reject other coins or tokens THIS STEP IS VERY IMPORTANT 6 Close and lock up ihe panel
3. make sure they are all good and connected firmly and not loose ii If the motor cannot work it m ans the motor is broken Please change a new motor 3 No any sound from sound speaker 1 Check if the VOLUME knob is on right position and adjust it to see what happens 2 Check if the sound speaker is damaged or broken 3 Make sure all plugs and wire lines related with sound speaker is good and connected firmly and not loose 4 Please check if the PCB is ok according to the way stated in 6 2 3 4 Machine continually works by itself without coins 1 Continually works by itself but without music a Please change or just take off the capacitor yellow color from the PCB and then restart the machine b If still problem it means the relay blue color on the PCB is broken and please changes a new reply to test Attached is a picture to show the capacitor and relay 2 Continually works by itself and with music Please check if coin acceptor was jammed by something or it s broken Please change a new coin accepter to try on the machine i F EW EN b period use the traps inside the machine will get loose or become slack After a fon Please change the invalid straps on time Over
4. aps or chains inside machines would get loose and the straps would possibly skid At this time please reposition the straps or chains inside the machines 6 Examine and Repair 1 LED light is not shining when turn on the electric switch on control box The LED light is not shining means the PCB is NOT power on Please make sure following things 1 The electric switch is connected well and not broken 2 The Motor Fuse and Line Fuse on the control box are not blown 3 All plugs and wire lines related with PCB are good and connected firmly and not loose Motor cannot start up and machine cannot work 1 Please check if the indicial LED light inside electric switch is shining or not 2 Please check if Motor Fuse and Line Fuse on the control box are blown 3 If the above is ok Please take off the PCB from the machine and test on another machine to see if the PCB is good or broken i If the PCB does not work on another machine please change the CPU on the PCB and try again If still not works we should change the whole PCB ii If the PCB works on another machine please qo tothe next step 4 If all above no problem but motors can not work please examine the motor by this way pull out the plug of the motor and coniect the motor to AC220V power supply by wire directly to see if the motor works i If the motor works correctly please cneck all plugs and wire lines related with motor and
Download Pdf Manuals
Related Search