Installation Instructions
Contents
1. specified tighten all bolts and fasteners to standard torque specifications listed within the OE Service Manual or as referenced in the torque specification list provided in these instruc tions Suspension components that use rubber or urethane bushings should be tightened with the vehicle at normal ride height This will prevent premature wear or failure of the bushing and maintain ride comfort Larger tire and wheel combinations may increase leverage on suspension steering and related components Due to payload options and initial ride height vari ances the amount of lift is a base figure Final ride height dimensions may vary in accordance to original vehicle ride height Always measure the vehicle ride height prior to beginning installation Vehicle ride height chart Driver Front Driver Rear Pass Front Pass Rear Stock Lifted Lifted Lifted a Lifted Torque Specs in FT LB Bolt Size Ss Torque Specs in FT LB Bolt Size Metric Metric Millimeters Grade 8 8 Grade 10 9 www ReadyLIFT com Phone 800 549 4620 2 Installation I nstructions 69 5112 Bill of Materials Front Strut Extension Front Sway Bar Drop Spacers M10 Flange Nuts M10 1 25 x 20mm Bolt w washer Front Diff Drop Kit Packaged 1 Rear Lift Blocks Skid Plate Spacer Kit Packaged The Bill of Materials represents the component contents of this kit All hardware is of the highest grade and the components are manufactured to ex2. 3 Install the 1 spacers between the differential sup 4 Re install the skid plate use two OEM bolts for the ports and the front cross member Install the new bolts front and the supplied and torque the bolts to factory with factory washers and the new nuts and washers specs Re install the wheels and torque to factory www ReadyLIFT com Phone 800 549 4620 4 Installation Instructions 69 5112 __ SKID PLATE SPACER INSTRUCTIONS Using the hardware provided install the M8 bolt washer skid plate and 1 2 tall spacer into the back two skid plate mounting points Use the OEM hardware for the two front mounting parts 1 Remove the sway bar from the 2 Install aluminum spacer to the 3 Repeat for the other side and frame on both sides Remove the frame using the hardware supplied torque bolts metal saddle and leave the bushing Note the position of the holes 4 Install sway bar saddle brackets 5 Repeat for the other side and 6 Sway bar spacer properly installed reusing the factory hardware torque all bolts www ReadyLIFT com Phone 800 549 4620 5 BISA f SUSPENSION INC Installation Instructions 69 5112 1 DO NO STACK BLOCKS AS IT IS DANGEROUS TO YOU AND OTHERS ANDIS ILLEGAL IN MOST STATES Rear Block Installation Remove the four 19mm nuts and two u bolts from one side of the vehicle 2 Using a jack and a block of wood carefully raise the truck by the leaf spring until there is enough room
3. BEAN E F SUSPENSION INC Installation I nstructions 69 5112 IF YOUR ReadyLI FT PRODUCT IS MISSING A PART OR HAS A DAMAGED PART PLEASE CONTACT CUSTOMER SERVI CE DI RECTLY A NEW REPLACEMENT PART WILL BE SENT TO YOU I MMEDI ATELY 800 549 4620 MON FRI 7AM 5PM PST OR EMAIL I NFO ReadyLl FT COM WEBSITE ReadyLl FT COM Please retain this document in your vehicle at all times Limited Lifetime Warranty This unique product warranty proves our commitment to the quality and reliability of every product that ReadyLl FT manufactures The ReadyLl FT product warranty only extends to the original pur chaser of any ReadyLI FT product if it breaks we will give you a new part Warranty does not apply to discontinued parts Our Limited Lifetime Warranty excludes the following ReadyLlI FT items bushings bump stops ball joints tie rod ends heims joints and shock absorbers These parts are subject to wear and are not considered defective when worn They are warranted for 12 months from the date of purchase for defects in workmanship This product warranty is voided if the vehicle is not aligned after kit installation and proper maintenance is routinely done Product purchased directly from ReadyLIFT has a 30 day return policy on uninstalled products from the date of pur chase Uninstalled product returns must be in the original ReadyLIFT packaging Please call 800 549 4620 to get an RGA for any return Customer is responsible for
4. acting specifications for a trouble free installation Use the attached torque specifications chart when final tighten ing of the nut and bolts are done 1 Remove the skid plate by unbolting the four 12mm 2 Starting from the passenger side loosen the upper bolts that hold it on and lower strut mount nuts 4 Remove the lower strut mount nut and bolt Push the lower control arm down www ReadyLIFT com Phone 800 549 4620 3 RISADM 4 a Installation ilies 69 5112 5 Remove the three upper strut mounting bolts Remove the strut from the vehicle and mount it in a bench vise Install the ReadyLift kit and torque fasten ers to OEM specifications Note the shape of the ReadyLift spacer the strut will be rotated 180 de grees when reinstalled 6 Reinstall the strut assembly in its stock 7 Repeat steps 2 location Leave the three upper strut mounting nuts through 6 on the loose Raise the lower control arm and install the lower Driver s Side of the strut mounting bolt and nut Use a floor jack to raise the vehicle Follow each lower control arm up in order to get the lower ball joint step closely making bolts installed Be sure to use a thread locker on the sure to double check lower ball joint bolts the torque on all fas Be sure to tighten all nut and bolts to factory specs teners oie a el ge 1 Position a floor jack under the front differential Raise the pad so that it is touching the diff
5. for the new block Install the ReadyLift 1 rear block Lower the jack and make sure that the leaf spring center pin goes into the hole on top of the block Install R eadyLift u bolts using the hardware provided Torque to 120 ft lbs Repeat on k a 3 y 3 a ak mL i r P ea i gt g he ine ae oe a oe a j x F T AEE es ages g i j i S a opposite side ITEE F esr z a a m i Site ft T 4 a p Final Checks amp Adjustments Post I nstallation Warnings Once the vehicle is lowered to the ground check all parts which have rubber or urethane components to insure proper torque Torque wheels to factory specs Move vehicle backwards and forwards a short distance to allow suspension components to adjust Turn the front wheels completely left then right and verify adequate tire wheel brake line and ABS wire clearance Test and inspect steering brake and suspension components for tightness and proper operation In spect brakes hoses and ABS lines for adequate slack at full extension Failure to perform the post in spection checks may result in vehicle component damage and or personal injury or death to driver and or passengers Test drive vehicle and re check the torque of all fasteners and re torque wheels on ve hicle Re adjust headlamps Vehicle Handling Warning Vehicles with larger tires and wheels will handle differently than stock vehicles Take time to familiarize yourself with the handling of your vehic
6. le Wheel Alignment Headlamp Adjustment It is necessary to have a proper and professional wheel alignment performed by a certified alignment technician Align the vehicle to factory specifications It is recommended that your vehicle alignment be checked after any off road driving In addition to your vehicle alignment for your safety and others it is necessary to check and adjust your vehicle headlamps for proper aim and alignment Vehicle Re Torque and Safety I nspection Upon completion of all services and adjustments performed on your vehicle and within 50 miles of driv ing check to ensure all fasteners and hardware are properly torqued to specification as noted in the vehicles factory service manual or the torque chart included www ReadyLIFT com Phone 800 549 4620 6
7. shipping costs back to ReadyLIFT Returns without RGA will be refused Contact ReadyLIFT directly about any potentially defective parts prior to removal from vehicle If the part in question is deemed warrantable an RGA will be assigned and can be returned for repair or replacement Replacement parts required prior to warranty claim completion must be purchased Upon receipt and verification of deemed warranty parts claim a credit or refund can then be processed to complete warranty claim transaction ReadyLIFT products are NOT intended for off road abuse Any damage or failure as a result from off road abuse voids the warranty of the ReadyLIFT product ReadyLIFT is NOT responsible for any subsequent damages to any related vehicle parts due to misuse abuse improper installation or lack of maintenance Furthermore ReadyLl FT reserves the right to change modify or cancel this warranty without prior notice www ReadyLIFT com Phone 800 549 4620 BRIEN S J SUSPENSION INC Installation I nstructions 69 5112 Please read I nstructions thoroughly and completely before beginning installation Installation by a certified mechanic is recommended ReadyLI FT Suspension I nc is NOT responsible for any damage or failure resulting from improper installation Safety Warning Suspension systems or components that enhance the on and off road performance of your vehicle may cause it to handle differently than it did from the factory Extreme care m
8. ust be used to prevent loss of control or vehicle rollover during abrupt maneuvers Always operate your vehicle at reduced speeds to ensure your ability to control your vehi cle under all driving conditions Failure to drive safely may result in serious injury or death to driver and passengers Driver and passengers must ALWAYS wear your seat belts avoid quick sharp turns and other sudden maneuvers ReadyLIFT Sus pension Inc does not recommend the combined use of suspension lifts body lifts or other lifting devices You should never operate your vehicle under the influence of alcohol or drugs Constant maintenance is required to keep your vehicle safe Thoroughly inspect your vehicle before and after every off road use Installation Warning All steps and procedures described in these instructions were performed while the vehicle was prop erly supported on a two post vehicle lift with safety jacks Use caution during all disassembly and assembly steps to insure Suspension components are not over extended causing damage to any vehicle components and parts included in this kit Included instructions are guidelines only for recommended procedures and are not meant to be definitive Installer is respon sible to insure a safe and controllable vehicle after performing modifications ReadyLIFT Suspension Inc recommends the use of an OE Service Manual for model year of vehicle when disassembly and assembly of factory and related components Unless otherwise
Download Pdf Manuals
Related Search