- autocodes.com
Contents
1. e There are 3 different length bolts which are identified by S short M medium L long enn 13 Remove the valve body Note the position of the Ratio Control Valve and attached shift link Figure 10 6 13 14 Make sure you replace the 2 lip seals shown in Figure 11 e Do not reuse the old lip seals e Use petroleum jelly to keep the new lip seals in place during reassembly 15 Carefully unpack the new valve body assembly When installing the new valve body be careful not to allow the Ratio Control Valve to fall out see Figure 10 e If the Ratio Control Valve does fall out check the condition of all surfaces especially the edges for damage e Confirm double check the direction of the shift link and the bottom of the shift link around the step motor pin see Figure 12 16 Route the harness around the outside of the Valve body as shown see Figure 13 Figure 13 7 13 17 Install the new valve body and shift link with the fork end of the shift link around the pin as shown see Figure 14 18 While you are doing Step 17 above the lower end of the shift link must stick through the bottom of the step motor pin as shown see Figure 15 e Install the CVT dipstick Figure 15 IMPORTANT CHECKS e Make sure the upper end forked end of the shift link is positioned around the pin after you install the new valve body Space is very limited in the work area e Make sure there i2. A Write down all radio station presets Presets 1 2 3 4 5 6 A C B Disconnect both battery cables negative cable first C Wait at least 3 minutes after the battery cables are disconnected 2 Remove the CVT dipstick Raise the vehicle on a hoist 2 13 3 Remove the undercover from below the front bumper cover see Figure 1 Figure 1 4 R the air guid ie N wn TT TE eo gue ne m w T BO dA a a Soe i 7 2 r Figure 2 CVT unit m connector 1 F6 5 Disconnect the CVT unit harness connector F6 by turning counterclockwise see Figure 3 Figure 3 6 Loosen and remove the transmission pan drain plug to remove the CVT fluid 7 Loosen and remove the 20 oil pan bolts to remove the oil pan 3 13 8 Remove the nut and lock nut to remove the manual plate 9 Remove the collar from the manual shaft 10 Remove the large lock ring holding the CVT connector to the transmission case see Figure 6 e Push the transmission side of the harness down inside the transmission case to remove it Figure 6 4 13 e Transmission side of CVT harness connector and lock ring shown removed from the transmission case see Figure 7 Figure 7 11 Disconnect the harness of the Primary oil pressure sensor 5 13 12 Remove the bolts attaching the valve body to the transmission see Figure 9 e There are 11 bolts shown and numbered for convenience
3. RO2C 1 a From the listed items find and select BATTERY CHARGE INITIATE ECU REPROGRAM PT ee TP030620 Figure C Battery Charging CONSULT II Elapsed Discharge Charge Time Vehicle 3 Check the CONSULT II s Charger Vole 0091 02 00 00 00 00 01 02 Teel Input reading see Figure D Battery Voltage Charger Input MUST BE ABOVE 8 32 1 2 1 5 12 00 VOLTS NOTE 0 100 0 10 20 30 40 50 60 70 80 90 100 pment 5 AC power e Battery Voltage is the voltage level Battery Charge IDLE EEA of CONSULT II s battery Start Discharge amp Charging Charge e Charger Input is the voltage level of MODE BACK LIGHT COPY the vehicle s battery It must be above TP0S068S 12 volts Figure D CAUTION If the Charger Input is below 12 volts e A list of items to check when Charger Input voltage is below 12V is contained in the TCM Reprogramming For Nissan Vehicles general procedure Click here to link to it Step Three Reprogram the TCM e lf you are not familiar with TCM Reprogramming click e This will link you back to a general procedure called TCM Reprogramming For Nissan Vehicles 12 13 Step Four TCM Reprogramming Wrap up 1 Turn the ignition and CONSULT II OFF 2 Disconnect CONSULT II from the vehicle 3 Start the Engine and make sure the MIL is OFF e If it s still ON use CONSULT II with the Diagnostic red white Ca
4. Technical Bulletin a SERVICE BULLETIN Classification AT05 009a NTB0O5 084a November 20 2006 MURANO LACK OF POWER ON TAKE OFF WITH DTC P0868 STORED IN THE TCM AND NO MIL ON This bulletin has been amended The Applied Vehicles have been updated Please discard all previous copies of this bulletin APPLIED VEHICLES 2003 2007 Murano 250 IF YOU CONFIRM A lack of power when accelerating from a standing start With DTC P0868 stored in the TCM but no MIL ON ACTIONS Step A Remove the original valve body and install the parts listed in the Parts Information section of this bulletin IMPORTANT Make sure to erase the EEPROM see step 28 page 9 Step B Reprogram the TCM see page 10 PRECAUTIONS WHEN REPLACING CVT VALVE BODY ASSEMBLY 1 If other DTCs are combined w P0868 resolve them first Refer to ASIST and the Service Manual for diagnostic information 2 If you observe excessive contamination in the oil pan and or can isolate an unusual noise coming from the transmission this TSB does not apply Refer to the Service Manual for further assistance 3 Transmissions are very vulnerable to particles dust metal etc e When replacing a CVT valve body make sure your work environment shop workbench etc the transmission area sub frame oil pan harness connector etc and your hands are free of contamination Make sure all parts are clean prior to installing on the vehicle e Unpack Service Par
5. ez Number L V ED Search by Code el per bulletin only e is PES ee wD Continus f This illustration is for example only your vehicle may be different TP030621h Figure A 1 Select vehicle model and model year example Murano 2004 2 Select the correct reprogramming data a Locate the specific Model Configuration Example VQ35 CVT 2WD NOTE Model Configuration may include items such as engine type transmission type and vehicle options such as ASCD TCS ABS etc 10 13 b Select click on the To number NOTE The To number will read 31036 XXXXX 3 Click on the Add button e This will add the data you selected to the File s Selected list 4 Write the To number on the Repair Order 5 Click on Continue and follow directions to perform data transfer download from ASIST into CONSULT II Step Two Preparation Steps Before Reprogramming TCM 1 Connect a battery charger to the vehicle s battery e Set the charger to a low charge rate trickle charge Do Not Connect A C Power Supply CAUTION For number 2 and number 3 cata Van on the next page DO NOT connect the CONSULT II A C Power Supply TP040090 Figure B 11 13 NISSAN ELECTRONIC CONTROL UNIT REPROGRAMMING 2 Press SUB MODE see Figure C then AE
6. rd to erase any DTC s that may have stored in the TCM and or the ECM during the reprogramming procedure 4 Confirm there are no leaks from the transmission Test drive the vehicle and make sure the transmission operates correctly in all modes and has a normal power level when starting from a stop e See the AT section of the appropriate Service Manual for operation specifications 13 13
7. s adequate clearance between the dipstick and harness 19 Install and torque the 11 valve body bolts removed in Step 12 see Figure 9 e Tightening torque 6 9 8 9 N m 0 7 0 9 kg m 61 78 in lb e Torque sequence as per Figure 9 6 7 5 8 4 9 3 10 2 11 1 20 Re install the collar on the manual shaft removed in Step 9 see Figure 5 8 13 21 Align the manual plate with the notch in the manual valve Manual plate Note First tighten 19 mm nut then tighten the 14 mm lock nut with the specified tightening torque i e Use a Torque wrench to tighten both the 14 mm and 19 mm nuts same torque spec for both 20 6 23 5 Nm 2 1 2 3 kg m 15 1 17 3 ft lb Figure 16 22 Reconnect the harness to the primary oil pressure sensor as shown in Step 11 and Figure 8 23 Reinsert the CVT connector with locking ring into the case as shown in Figure 6 and Figure 7 Check that the locating notch is properly engaged 24 Install the oil pan and bolts e Make sure oil pan and magnets are free of contamination particles e Tightening Torque Aluminum oil pan 5 4 7 4 N m 0 5 0 7 kg m 3 9 5 4 lb ft Iron oil pan 6 9 10 8 N m 0 7 1 1 kg m 5 0 7 9 lb ft 25 Install the battery cables Negative cable last 26 Fill and check the CVT fluid level 27 Reprogram the radio presets 28 Erase the TCM EEPROM memory Connect CONSULT II to data link connector Turn ignition switch ON Confirm tha
8. t CONSULT II is turned ON Move selector lever to R position Touch START on CONSULT II On CONSULT II select TRANSMISSION gt SELF DIAG RESULTS Press on the Brake Brake switch ON Press the accelerator pedal 0 5 8 4 8 throttle not to exceed half and hold it in the half or less open position This will set the closed throttle position signal to OFF and the wide open throttle position signal to OFF On CONSULT II touch ERASE then touch YES i Wait 3 seconds and then release the accelerator pedal j Turn ignition switch OFF ea oaa0o0m g 9 13 Step B REPROGRAM THE TCM Vehicle TCM Reprogramming Overview e There are four basic steps 1 Download transfer reprogramming data from ASIST into CONSULT II 2 Preparation steps before reprogramming TCM 3 Reprogram the TCM 4 Wrap up after reprogramming is finished Step One Download Transfer Reprogramming Data From ASIST Into CONSULT II e f you re not familiar with the latest TCM reprogramming procedures clicl here This will link you to the TCM Reprogramming For Nissan Vehicles general procedure or refer to it in the print copy of this bulletin e For those familiar with TCM Reprogramming please review the following steps and use them as a Quick Reference for TCM reprogramming ECU Electronic Control Unit Vehicle Reprogramming Data Model ee ang ur a 1 File s selected To 31036 XXXXX z To Sent
9. ts just before installation IMPORTANT The purpose of ACTIONS above is to give you a quick idea of the work you will be performing You MUST closely follow the entire Service Procedure starting on page 2 as it contains information that is essential to successfully completing this repair Nissan Bulletins are intended for use by qualified technicians not do it yourselfers Qualified technicians are properly trained individuals who have the equipment tools safety instruction and know how to do a job properly and safely NOTE If you believe that a described condition may apply to a particular vehicle DO NOT assume that it does See your Nissan dealer to determine if this applies to your vehicle 1 13 PARTS INFORMATION DESCRIPTION Valve body AssembI Gasket oil pan Nissan CVT Fluid Seal lip Bolt hex Bolt Bolt flange hex Seal O ring drain plug Aluminum pan only Wash drain plug Steel pan onl Bolt Aluminum pan only Bolt Steel pan onl CLAIMS INFORMATION Submit a Primary Failed Part PP line claim using the following claims coding DESCRIPTION PFP OP CODE SYM DIA FRT RPL Valve Body Ass JXO5AA Reprogram TCM ie JEQ9AA Me tiie a 1 Reference the Parts Information Table and use the applicable Valve Body Assy P N as the PFP 2 Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT SERVICE PROCEDURE Step A Remove and replace the valve body 1
Download Pdf Manuals
Related Search