genuine parts installation instructions
Contents
1. Pass the iPod connector black connector end of the iPod cable through the rectangular glove box lamp opening Slide the grommet into the 10mm 3 8 slot The grommet slit Should point toward the vehicle rear Fig 16 12 Re install the glove box lamp in the glove box inner 13 Re Connect the glove box lamp connectors Fig 6 14 Re connect the trunk release connector Fig 6 15 Re install the glove box inner 10 screws Fig 5 16 Pull the excess iPod cable through the grommet Do not pull with excessive force or cable could be damaged 17 Re connect the glove box outer tether Fig 5 18 Re install the glove box outer Fig 17 19 Verify the iPod cable is visible inside the glove box Fig 17 999U7 DV100II REV 1 07 21 08 INSTALLATION INSTRUCTIONS iPod 11 TRIM I NSTALLATI ON 1 Re install RH side dash panel forward of kicking panel and forward corner of RH footwell Verify all harnesses are tucked and secured properly Re install the plastic nut for RH side dash panel and front bracket Re install the RH defrost and weather strip Re install the RH side kicking plate Fig 1 Verify glove box and panels fit and finish 12 FUNCTIONAL VERIFICATION AND PACKAGING DISPOSITION 1 Re connect battery negative terminal 2 Verify the trunk release is operational 3 Verify the glove box lamp is operational 4 If available key on vehicle and connect iPod to cable Press aux mode button un2. engine hood 7 Disconnect the negative battery terminal 8 Remove RH side kicking plate Fig 1 9 Remove Plastic nut from RH side dash panel and remove RH side dash panel Fig 2 Plastic Nut 10 Loosen 12 of weather strip in circled area Fig 3 11 Remove RH defrost panel by applying a pressure at pry points as shown with PGF Loosen stick Fig 3 weather strip li fa 7 fie I Page 2 of 8 999U7 DV100II REV 1 07 21 08 INSTALLATION INSTRUCTIONS iPod 12 Remove glove box outer by moving side to side and pulling up Fig 4 Refer to service manual for more details 13 Detach glove box outer tether Fig 5 14 Remove glove box inner screws 10 places Be sure to remove all hidden screws Fig 5 15 Glove box inner should come out easily once all screws have been removed 16 Disconnect trunk release connector Fig 6 17 Disconnect glove box lamp connector Fig 6 Disconnect harness 18 Remove glove box lamp system Fig 7 Remove lamp system Page 3 of 8 999U7 DV100II REV 1 07 21 08 INSTALLATION INSTRUCTIONS iPod 8 iPod MODULE SAE aA 1 Locate area for iPod module installation 100mm from bottom and along sheet metal edge Fig 8 2 Attach ground strap to RH side of iPod module with 1 M5x8mm screw and torque to 2 Nm Fig 9 3 Install 1 M5x8mm screw in LH side of iPod module and torque to 2 Nm 4 Clean back of iPod module and mating shee
3. CPM Beam Hole 10 Route iPod main cable toward driver side and secure to factory harness using cable ties 3 and 1 push pin Fig 13 Push pin and tie strap in cross beam y ow 2 Tie Straps Htigalisi Page 5 of 8 999U7 DV100II REV 1 07 21 08 INSTALLATION INSTRUCTIONS iPod 10 iPod CABLE INSTALLATION Position the glove box inner so the lamp 3 mm Pilot Opening is visible Hole 2 Place masking tape above lamp opening toward rear of vehicle Fig 14 Measure 11 mm 7 16 from lamp opening and mark the center of the first hole Fig 14 Measure 4 mm 5 32 from lamp opening and mark the center of the second hole Fig 14 5 Drill two 3mm 1 8 pilot holes at marked points Fig 14 6 Open holes to 10 mm 3 8 Fig 14 7 Smooth out opening with drill bit file or flash removal tool Fig 15 Dashed line 8 area must be removed Remove masking tape Page 6 of 8 999U7 DV100II REV 1 07 21 08 INSTALLATION INSTRUCTIONS iPod Grommet slit should point toward vehicle rear Apply foam tape around connector Vehicle rear and secure with 1 Fig 16 cable tie Page 7 of 8 9 Slit the grommet and place it on the iPod cable 10 Connect the iPod cable black grey connector to the iPod main cable grey connector Wrap a piece of foam tape around the connectors and tie strap the connectors and iPod cable to the glove box lamp harness Fig 16 11
4. GENUINE PARTS D a INSTALLATION INSTRUCTIONS DESCRIPTION iPod 1 2 APPLICATION GT R 2009 3 PARTNUMBER iPod main kit 999U7 DV000 item QTY Description Service Part Number 6 6 Single Sided Adhesive Foam Tape Part of 999U7 DVOOSP e 10 e Tie Straps S C lt S C art OF NIU DVOOSP 9 1 eomme SO Partofoa9U7 DVOOZSP 5 TOOLS REQUI RED e PGF stick e Plastic pry bar e Flash Removal e Tape measure e Philips 2 e Torx T 20 e Portable Light e Drill 3mm 1 8 bit l0mm 3 8 bit PRE I NSTALLATI ON CAUTI ONS NOTES e Dealer Installation Recommended Instructions refer to Service Manual e This part is to be installed at a surface temperature of 65 100 F Ay CAUTION e Glove box has many hidden screws When all screws have been removed glove box comes out easily e Maximum M5 screw length is 8 mm The use of longer screws will damage the iPod module e Do not touch or contaminate the cleaned sheet metal or the adhesive tape on the iPod module to prevent the adhesion strength from being reduced Page 1 of 8 999U7 DV100II REV 1 07 21 08 INSTALLATION INSTRUCTIONS iPod 7 VEHICLE PREPARATION 1 Verify vehicle shift lever is in the P position 2 Apply the parking brake 3 Record the customer radio presets 4 Move the front passenger seat to the most rearward position 5 Turn the ignition switch OFF 6 Open the
5. t metal area with 70 30 alcohol water wipe Allow surface to dry 5 Apply one piece of double sided adhesive tape to the back of the iPod module non label side Remove tape backing 6 Measure 100mm from bottom and 50mm from edge of BCM Orient iPod module with connector pointing down or slightly toward the rear of the vehicle and press iPod module firmly to the sheet metal maximize flat area Fig 8 and 9 7 Remove BCM bracket screw and secure the iPod module ground strap to the vehicle sheet metal with the BCM bracket screw Secure ground strap to sheet metal with one piece of Single sided tape Fig 10 Page 4 of 8 999U7 DV100II REV 1 07 21 08 INSTALLATION INSTRUCTIONS iPod 9 CABLE ROUTING 1 Press iPod module against sheet metal for Support 2 Connect main iPod cable 24 pin connector white to iPod module Fig 11 iPod main able coin k V a A N N d x a 3 Locate and untape 12 connector white taped and 12 pin jue gt to factory pre wiring Fig 11 connectors D S ASS E 7 ie 4 Connect main iPod cable 12 pin connector Foam tape on 12 white to factory pre wiring Fig 11 pin connectors 5 Wrap 12 pin connector with foam tape Fig 11 6 Route iPod main cable up following existing factory harness path using cable ties 2 Fig 11 7 Locate hole in CPM beam Fig 12 8 Install push pin in CPM beam hole 9 Install cable tie through push pin
6. til iPod mode is selected iPod should play music Program customer s radio presets to the recorded settings Verify radio presets function properly Confirm vehicle systems operate properly If equipped verify sunroof operation Refer to Service Manual for requirements Place iPod operation manual in glove box and close glove box Inspect the vehicle interior and exterior for damage Properly dispose recycle if possible iPod kit packaging installation instructions and extra parts Page 8 of 8 999U7 DV100II REV 1 07 21 08
Download Pdf Manuals
Related Search