ADVANCED AUDIO XM SATELLITE RADIO KIT - Harley
Contents
1. 00310a The XM Radio requires up to 400 milliamps additional current from the electrical system Kit Contents See Figure 6 and Table 1 INSTALLATION WARNING To prevent accidental vehicle start up which could cause death or serious injury remove maxi fuse before pro ceeding 00251a Refer to the Service Manual and follow the instructions given to remove the maxi fuse s N Remove the outer fairing and windshield Refer to OUTER FAIRING WINDSHIELD REMOVAL in the Service Manual NOTE If another module has been installed in the location reserved for the XM radio module relocate that module per the instructions supplied with that kit Please dispose of materials responsibly is00357 1 XM radio module 2 Radio case screw 3 Grommet 2 Figure 1 XM Radio Module Installation 3 See Figure 1 Locate the XM radio module 1 on top of the AM FM radio case a Remove the screw 2 at the back of the radio b Position the XM radio module on top of the AM FM radio with the metal cones on one end of the module fitting firmly into the leftmost rubber grommets 3 at the front of the radio c Fasten the module to the radio with the radio case screw 2 Tighten to 35 45 in Ibs 4 0 5 1 Nm 4 Obtain the antenna bracket purchased separately FLH models See Figure 2 Remove the fairing mounting screw 2 at the top of the left side fairing support bracket 1 Clip the antenna2. bracket 3 over the top edge of the support bracket and fasten the antenna bracket through the support bracket to the inner fairing with the screw removed earlier Tighten to 20 30 in Ibs 2 3 3 4 Nm FLT models See Figure 3 Remove the left side radio mounting screws 2 Position the antenna bracket 3 to the side of the radio carrier bracket 1 with the top plate horizontal lining up two of the diagonal holes in the antenna bracket with the radio mounting holes Fasten the antenna bracket through the radio carrier bracket to the radio with the screws removed earlier Tighten to 35 45 in Ibs 4 0 5 1 Nm 5 All models Obtain the XM radio antenna 4 two sided adhesive tape 5 and alcohol wipe 6 from the kit Use the alcohol wipe to thoroughly clean the inscribed diagram area on the horizontal antenna mounting surface of the antenna bracket and the bottom mounting surface of the antenna 6 Peel the liner from one side of the tape and apply the tape squarely to the bottom surface of the antenna 7 Peel the liner from the exposed side of the adhesive tape on the antenna base 8 Position the antenna over the diagram on the bracket without touching the adhesive to the bracket Center the antenna over the diagram with the antenna cable toward the radio J03640 is00358 Left side fairing support bracket Fairing mounting screw Antenna bracket left hand XM satellite radio antenna Adhesive tape two s
3. cMOTOR HARLEY DAVIDSON WY J03640 INSTRUCTIONS REV 2005 08 04 ADVANCED AUDIO XM SATELLITE RADIO KIT GENERAL Kit Number 76404 06 Models This kit fits 2006 and later FLHT Electra Glide FLHTC Electra Glide Classic FLHTCU Ultra Classic Electra Glide FLHX Street Glide and FLTR Road Glide model motor cycles XM satellite radio is available within the continental United States It is not available in Alaska or Hawaii Additional Parts Required FLHT models will require prior installation of an Advanced Audio AM FM CD Radio Kit Part Number 76412 06 and an AM FM Antenna Kit Part Number 76325 06 or 7631 7 06 Unless one has already been fitted as part of another Advanced Audio kit installation FLHT FLHTC and FLHX models will require the additional purchase of a Non Ultra Overlay Harness Part Number 70169 06 and a left hand Antenna Bracket Part Number 76456 06 FLHTCU models will require the additional purchase of an Ultra Overlay Harness Part Number 70164 06 and a left hand Antenna Bracket Part Number 76456 06 FLTR models will require the additional purchase of a Non Ultra Overlay Harness Part Number 70169 06 and an Antenna Bracket Part Number 76316 06 If two modules are already installed on top of the radio two Dual Lock mounts Part Number 76434 06 will be needed These items are available from a Harley Davidson Dealer WARNING The rider s safety depe
4. erlay harness 12 place socket housing 1 labelled XM 185 into the pin housing coming from the back of the XM radio module Plug the 35 place radio socket housing 28 2 into the radio Locate the interconnect harness audio connector 6B near the back of the radio Plug 6 way pin housing 6A 3 on the overlay harness into socket housing 6B 13 14 15 FLHTCU models See Figure 5 a Unplug the two halves of the 12 place CB connector 184 Plug the overlay harness C 12 place socket housing 1 labelled CB 184 into pin housing 184A coming from the back of the CB module Plug the overlay harness 12 place pin housing 2 also labelled CB 184 into the audio harness connector 184B Plug the overlay harness 12 place socket housing 3 labelled XM 185 into the pin housing coming from the back of the XM radio module Use tie straps from the kit to fasten the overlay harness to the existing harnesses inside the fairing Verify that the Ignition Light Key Switch is in the OFF position Refer to the Service Manual and follow the instructions given to re install the maxi fuse Test the XM radio and the rest of the sound system for proper operation 3of4 16 Re install the outer fairing and windshield Refer to OUTER Manual FAIRING WINDSHIELD INSTALLATION in the Service SERVICE PARTS _ 2 2e Figure 6 Service Parts Touring XM Rad
5. ided Alcohol wipe 1 2 3 4 5 6 Figure 2 XM Radio Antenna Mounting FLH Models is00359 ong Radio carrier bracket Radio mounting screw 2 Antenna bracket XM satellite radio antenna Adhesive tape two sided Alcohol wipe OST Ri EE Figure 3 XM Radio Antenna Installation FLT Models 10 11 Press the antenna squarely and firmly onto the bracket and hold pressure for about 60 seconds After releasing pressure avoid direct contact with the antenna for about 20 minutes Insert the pink connector on the antenna cable into the mating pink connector on the back of the XM radio module Use tie straps from the kit to tie the antenna wire to the existing harnesses inside the fairing and loop the excess wire together 2 of 4 is00364 1 12 place socket housing 185 labelled XM to XM satellite radio module 2 35 place socket housing 28 to AM FM radio 3 6 place pin housing 6A labelled Interconnect Figure 4 Non Ultra Overlay Harness is00365 1 12 place socket housing 184 labelled CB 2 12 place pin housing 184 3 12 place socket housing 185 labelled XM Figure 5 Ultra Overlay Harness 12 Obtain the overlay harness purchased separately unless already installed FLHT FLHTC FLHX and FLTR models See Figure 4 a J03640 Plug the ov
6. io Kit Table 1 Service Parts Table Item Description Quantity Part Number XM satellite radio module Not Sold Separately 2 XM radio antenna 76337 06A 3 Adhesive tape two sided Not Sold Separately 4 Alcohol wipe 74678 00Y 5 Tie wrap 3 10181 6 Owner s Manual not shown 76405 06 Items mentioned in text but not included in kit A Antenna Bracket left hand FLH B Antenna Bracket FLT C Ultra overlay harness D Non Ultra overlay harness J03640 4 of 4
7. nds upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet references Service Manual information A Service Manual for your model motorcycle is required for this installation and is available from a Harley Davidson Dealer J03640 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled Electrical Overload NOTICE It is possible to overload your motorcycle s charging system by adding too many electrical accessories If your combined electrical accessories operating at any one time consume more electrical current than your vehicle s charging system can produce the electrical consumption can discharge the battery and cause vehicle electrical system damage See a Harley Davidson dealer for advice about the amount of current consumed by additional electrical accessories or for necessary wiring changes 0021 1b WARNING When installing any electrical accessory be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modi fied Exceeding the maximum amperage can lead to elec trical failures which could result in death or serious injury
Download Pdf Manuals
Related Search