INSTALLATION INSTRUCTIONS
Contents
1. All Rights Reserved All 47363 1208 50 If the vehicle is equipped with a moonroof install the drain clip to the control unit bracket CONTROL UNIT BRACKET DRAIN CLIP 51 Install the control unit bracket to the vehicle panel with one 6 mm flange nut CONTROL UNIT 6mm FLANGE NUT BRACKET VEHICLE PANEL FRONT VEHICLE NTROL PANEL BRACKET 15 of 21 If the vehicle is equipped with a moonroof continue with step 52 Otherwise go to step 55 52 Release the drain tube one clip CONTROL UNIT VEHICLE BRACKET PANEL FRONT VEHICLE CLIP Slide DRAIN CLIP 53 Slide the drain tube as shown and secure it to the vehicle panel with the vehicle clip just moved 54 Secure the drain tube to the control unit bracket with the drain clip Routing the Control Unit Harness 55 Using isopropyl alcohol on a shop towel thoroughly clean the area where the fuse label will attach Attach the 5A trailer small It fuse label to the fuse case on the control unit harness FUSE CASE 5A TRAILER SMALL LT FUSE LABEL CONTROL UNIT 56 Locate and unplug the vehicle 13 pin connector as shown FRONT a LES 76 SS gt NON VEHICLE 13 PIN CONNECTORS If the vehicle is equipped with a accessory backup sensor continue with step 57 Otherwise go to step 60 57 Unplug the vehicle 13 pin connector from t2. UNIT J HARNESS Clean with isopropyl ALUMINUM alcohol TAPE VEHICLE PANEL Using isopropyl alcohol on a shop towel thoroughly clean the area where the aluminium tape will attach Secure the control unit harness to the vehicle panel with one aluminum tape Secure the 4 pin connectors 2WD vehicle Plug the control unit harness 4 pin connector to the socket harness 4 pin connector and using isopropyl alcohol on a shop towel thoroughly clean the area where the aluminum tape will attach Secure the 4 pin connectors to the vehicle panel CONTROL UNIT HARNESS SOCKET HARNESS 4 PIN CONTROL UNIT CONNECTOR HARNESS 4 PIN CONNECTOR VEHICLE PANEL FRONT 4 PIN Clean with CONNECTORS isopropyl alcohol 2012 American Honda Motor Co Inc All Rights Reserved 4WD vehicle Plug the control unit harness 4 pin connector to the socket harness 4 pin connector and secure the 4 pin connectors to the vehicle harness with one wire tie CONTROL UNIT HARNESS SOCKET HARNESS SOCKET HARNESS 4 PIN CONTROL UNIT CONNECTOR HARNESS 4 PIN CONNECTOR FRONT VEHICLE WIRE HARNESS 4 PIN TIE CONNECTORS 67 Install the connector clip to the fuse case on the control unit harness TRAILER UNIT HARNESS CASE CLIP 70 VEHICLE PANEL 71 72 FRONT CONNECTOR CLIP 68 Route the fuse case on the control
3. HONDA INSTALLATION INSTRUCTIONS PARTS LIST Trailer Hitch Kit P N 08L92 TOA 100 Trailer hitch Ball mount 6 Hex bolts 10 x 40 mm 6 Spring washers 10 mm 6 Plain washers 10 mm Hex bolt 12 x 50 mm Spring washer 12 mm 2 Plain washers 12 mm So e e 2012 American Honda Motor Co Inc All Rights Reserved Accessory TRAILER HITCH Application Publications No 2013 CR V Issue Date Hex nut 12 mm 2 Hitch pin 9 Hitch pin clip Ss Receiver cover Center plate Sy 4 Trailer Hitch Harness Kit P N 08L91 T0A 100 0 J is wat Control unit bracket Control unit harness Socket harness All 47363 1208 08L92 TOA 1000 90 1 of 21 Drain Clip Control unit bq Sp 2 Hex bolts 6 x 40 mm Fuse label 3 Flange nuts 6 mm 8 7 5A Fuse Pillar clip 2 Wire ties with clip 7 Wire ties ZA 4 Aluminium tapes Accessory User s Information Manual O Connector clip 2 of 21 All 47363 1208 2012 American Honda Motor Co Inc All Rights Reserved TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Small flat tip screwdriver 10 mm Open end wrench 10 mm 14 mm 17 mm and 19 mm Sockets Pushpin Ratchet 3 mm and 6 mm Drill bits Eye protection face shield safety goggles etc File Blanket Isopropyl alcohol Shop towel 20 mm Hole saw Drill Tape Hex wrench Diagonal cutters Felt tip pen Ut
4. Torque the 12 x 50 mm hex bolt to 79 58 Ibf ft 2 HEX BOLT 12 x 50 mm 79 N m 58 Ibf ft 6 HEX BOLTS 10 x 40 mm 46 N m 34 Ibf ft 33 Reconnect the muffler bushings to the vehicle pins 2012 American Honda Motor Co Inc All Rights Reserved All 47363 1208 34 Using a felt tip pen mark the rear under cover at the measurements shown FRONT VIEW REAR CURVE UNDER COVER FELT TIP PEN 0 2 in 5mm RIB 0 2 in RIB 2 S amp _ Q lt REAR UNDER COVER SA ie 7 35 Using pushpin pierce the center of each mark made in step 34 on the rear under cover REAR UNDER COVER PUSHPIN 20 mm BREE HOLE SAW 36 While wearing eye protection drill each pierced mark on the rear under cover First drill with a 3 mm drill bit then enlarge each hole to 20 mm using a 20 mm hole saw 11 of 21 37 While wearing eye protection use air saw to cut the rear under cover at the mark made in step 34 Remove any burrs and sharp edges from the corners AIR SAW Mark made in step 34 Cut off REAR UNDER COVER 38 Using a felt tip pen mark the rear under cover at the measurements shown FRONT VIEW CURVE 25mm END 1 0 59 mm REAR UNDER COVER 12 of 21 All 47363 1208 39 Using an air saw cut the rear under cover at the mark made in step 38 Remove any burrs and sharp edges from the
5. corners AIR SAW Mark made in step 38 REAR UNDER COVER Cut off 2012 American Honda Motor Co Inc All Rights Reserved 40 2012 American Honda Motor Co Inc All Rights Reserved Using an air saw cut the rear under cover along the scribe line as shown Remove any burrs and sharp edges from the corners NOTE Some rear under covers may not have the scribe line If not use the measurements shown REAR UNDER REAR Z UNDER COVER Routing the Socket Harness 41 Secure the socket harness to the trailer hitch with two 6 x 40 mm flange bolts and two 6 mm flange nuts TRAILER HITCH 2 FLANGE NUTS 6mm TRAILER 2 FLANGE SOCKET HITCH BOLTS HARNESS 6 x 40 mm 42 Route the socket harness along the rear bumper as 43 All 47363 1208 shown 2 WIRE TIES WITH CLIP SOCKET HARNESS BUMPER SOCKET BEAM HARNESS TRAILER HITCH WIRE TIE At the first green tape secure the socket harness to the trailer hitch with one wire tie At the next two green tapes secure the socket harness to the vehicle panel with two wire ties with clip 13 of 21 44 Route the socket harness as shown and secure it to the hole in the bumper beam with one wire tie Clean with isopropyl alcohol SOCKET ALUMINUM TAPE HARNESS 7 VEHICLE PANEL BUMPER TIE BEAM Align 45 Using isopropyl alcohol on a shop towe
6. d the vehicle clip and install the new clip to the left D pillar trim WITH SIDE CURTAIN AIRBAG NEW CLIP VEHICLE CLIP Discard LEFT D PILLAR TRIM LEFT D PILLAR TRIM Check the overlap between the headliner and the D pillar trim NOTE Check and adjust the overlap as described in the Service Manual Reinstall the left D pillar trim NOTE Make sure the side curtain airbag is not tucked under the clip Do not push the D pillar trim excessively Check that all wire harnesses are routed properly and all connectors are plugged in Reinstall all removed parts Reconnect the negative cable to the battery Press and hold the radio power button for two seconds to restore the radio and navi if equipped system functions Reset the clock 2012 American Honda Motor Co Inc All Rights Reserved Give copy of this page to your customer Whenever you remove the hitch pin clip the hitch pin and the ball mount store them securely in the cargo area Install the receiver cover into the opening at the end of the trailer hitch When you reinstall the ball mount store the receiver cover in the cargo area TRAILER HITCH RECEIVER COVER Install the ball mount the trailer hitch using a hitch pin clip and hitch pin HITCH PIN TRAILER HITCH HITCH PIN CLIP HITCH PIN BALL MOUNT After the first 600 miles 1 000 km of towing have your Honda Dealer re check the tightness of the trailer
7. d with a shop towel lightly tap the area marked SIDE CURTAIN AIRBAG on the left D pillar trim to push the clip Make sure to strike area perpendicularly to the vehicle 7 of 21 21 22 23 8 of 21 Remove the left D pillar trim ten clips WEATHERSTRIP Pull away 10 CLIPS LEFT D PILLAR TRIM Open the right rear door RIGHT REAR WHEEL ARCH PROTECTOR 2 SCREWS CLIP Remove the one clip and the two screws from the right rear wheel arch protector If equipped remove the splash guards 24 25 26 All 47363 1208 Remove the right rear wheel arch protector eleven clips and two retaining tabs RIGHT REAR FENDER 6 CLIPS RETAINING TAB RIGHT REAR WHEEL ARCH PROTECTOR 5 CLIPS RETAINING TAB Remove the left rear wheel arch protector the same way On each side of the vehicle apply masking tape to the rear bumper right taillight and right rear fender as shown RIGHT RIGHT REAR FENDER TAILLIGHT MASKING TAPE REAR BUMPER 2012 American Honda Motor Co Inc All Rights Reserved 27 Remove the rear bumper e On each side release four retaining tabs e Remove the two covers two bumper screws two bolts two screws and five clips 2 COVERS RIGHT TAILLIGHT 2 SCREWS REAR BUMPER REAR BUMPER 2BOLTS 2 BUMPER SCREWS 5 CLIPS e With the help of an assistant remove the rear bumper Place
8. e tab and two hooks LEVER SHOP Pull TOWEL TAB 2 HOOKS LEFT REAR SIDE TRIM PANEL 14 Remove two screws 6 of 21 All 47363 1208 15 Press the center of the hook and remove the hook from the left rear side trim panel Press the center to remove FRONT LEFT REAR SIDE TRIM PANEL 16 Remove the tie down hook one bolt TIE DOWN HOOK LEFT REAR SIDE TRIM PANEL 2012 American Honda Motor Co Inc All Rights Reserved 17 Pull away the weatherstrip from around the left rear side trim panel at the tailgate and remove the door opening seal at the left rear door Starting at the front release the left rear side trim panel eight clips and seven retaining tabs WEATHERSTRIP Pull away TRETAINING DOOR OPENING SEAL Pull away LEFT REAR SIDE TRIM PANEL 18 Release the wire and remove the left rear seat release lever two clips and five retaining tabs then remove the left rear side trim panel 2 CLIPS 5 RETAINING S WIRE LEFT REAR SEAT RELEASE LEVER LEFT REAR SIDE TRIM PANEL 2012 American Honda Motor Co Inc All Rights Reserved All 47363 1208 19 Pull away the door opening seal from around the left D pillar trim VEHICLE PANEL VEHICLE PANEL Strike perpendicularly to the vehicle LEFT D PILLAR TRIM LEFT FRONT D PILLAR TRIM SHOP RUBBER TOWEL MALLET 20 Using a rubber mallet wrappe
9. he backup sensor harness 13 pin connector VEHICLE 13 PIN HARNESS Clean with isopropyl alcohol 16 of 21 All 47363 1208 2012 American Honda Motor Co Inc All Rights Reserved 58 Plug the control unit harness 13 pin connector into the backup sensor harness 13 pin connector CONTROL UNIT HARNESS 13 PIN CONNECTOR BACKUP SENSOR HARNESS 13 CONNECTOR FRONT Z W S X O K zM V SS Ve 62 CONTROL UNIT HARNESS 59 Plug the vehicle 13 pin connector into the control unit harness 13 pin connector Go to step 61 2012 American Honda Motor Co Inc All Rights Reserved All 47363 1208 60 Without backup sensor harness Plug the two control unit harness 13 pin connectors in between the two vehicle 13 pin connectors CONTROL UNIT HARNESS 13 PIN CONNECTORS A VEHICLE 13 PIN CONNECTORS CONTROL UNIT HARNESS 17 of 21 61 Route the control unit harness along the vehicle 64 harness CONTROL UNIT HARNESS FRONT CONTROL UNIT CONTROL HARNESS 14 PIN UNIT CONNECTOR 65 62 Plug the control unit harness 14 pin connector into the control unit 63 Secure the control unit harness to the vehicle 66 harness with three wire ties VEHICLE HARNESS CONTROL UNIT HARNESS FRONT 3 WIRE TIES CONTROL UNIT 18 of 21 All 47363 1208 Route the control unit harness as shown CONTROL NI
10. hitch bolts 2012 American Honda Motor Co Inc All Rights Reserved All 47363 1208 21 of 21
11. ility knife Rubber mallet Torque wrench Ruler The following tools are available through the Honda Tool and Equipment program On the iN click on Service gt Service Bay gt Tool and Equipment Program then enter the number under Search Or call 888 424 6857 Air Saw Snap on 192 Trim Tool Set T N SOJATP2014 2012 American Honda Motor Co Inc All Rights Reserved All 47363 1208 Illustration of the Trailer Hitch on the Vehicle CONTROL UNIT HARNESS 5A FUSE TRAILER HITCH CONTROL SOCKET UNIT HARNESS INSTALLATION Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers 1 Disconnect the negative cable from the battery 2 Remove the driver s dashboard under cover turn the knob one clip and one pin DRIVER S DASHBOARD PIN UNDER COVER 3 of 21 3 If equipped remove the tonneau cover compress 5 the spring loaded end and remove SPRING LOADED END TONNEAU VEHICLE PANEL HOLDER TONNEAU COVER 4 Pull the lever and fold down the left rear seat LEVER Pull A LEFT REAR SEAT Fold down 7 4 of 21 All 47363 1208 Lift the left rear seat back LEFT REAR SEAT BACK Lift Re
12. l thoroughly clean the area where the aluminium tape will attach Secure the socket harness to the vehicle panel with one aluminum tape 46 Remove the forward vehicle grommet from the vehicle panel and route the socket harness through the hole Seat the grommet on the socket harness to the vehicle panel hole NOTE Do not pull on the socket harness when installing the grommet GROMMET HOLE VEHICLE PANEL VEHICLE GROMMET SOCKET Discard HARNESS 14 of 21 All 47363 1208 47 Using isopropyl alcohol on a shop towel thoroughly clean the area where the aluminium tape will attach Secure the socket harness to the vehicle panel with one additional aluminum tape SOCKET HARNESS VEHICLE PANEL SOCKET Clean with HARNESS isopropyl alcohol ALUMINUM TAPE 48 Inside the vehicle secure the socket harness 2WD vehicle Route the socket harness as shown and secure it to the vehicle panel with one wire tie TIE VEHICLE FRONT E SOCKET PANEL HARNESS 2012 American Honda Motor Co Inc All Rights Reserved 4WD vehicle Route the socket harness along the vehicle harness and secure it to the vehicle harness with one wire tie VEHICLE HARNESS SOCKET HARNESS Installing the Control Unit 49 Install the control unit bracket to the control unit CONTROL UNIT CONTROL UNIT BRACKET 2012 American Honda Motor Co Inc
13. move the left rear door sill trim three clips five retaining tabs and one hook LEFT REAR 5 RETAINING DOOR SILL TRIM TABS FRONT 3 CLIPS Pull the lever and fold down the left rear seat back 2012 American Honda Motor Co Inc All Rights Reserved 8 2012 American Honda Motor Co Inc All Rights Reserved Remove the cargo floor board two hooks CARGO FLOOR BOARD 2 HOOKS Pull away the weatherstrip and remove the rear trim panel two retaining tabs six clips and two hooks 2 CLIPS 4 CLIPS REAR TRIM Nes 2 RETAINING TABS WEATHERSTRIP Pull away 10 Remove the left rear damper cover seven retaining 11 All 47363 1208 tabs four hooks and lift up LEFT REAR SIDE TRIM PANEL ze 2 SNS KSX S RY x QX 2 AN NY 4 2 7 4 LEFT REAR DAMPER COVER 7 RETAINING TABS Release the floor carpet from the left floor carpet cover three clips 3 CLIPS IN FRONT LEFT REAR A LEFT FLOOR SIDE TRIM CARPET COVER 5 of 21 12 Remove the left floor carpet cover three clips and two retaining tabs LEFT FLOOR CARPET COVER FRONT 5 RETAINING LEFT REAR SIDE TRIM PANEL SEAT EAR 13 Gently pull the lever on the left rear side trim panel and use a small flat tip screwdriver wrapped with a shop towel to remove the inner handle cap on
14. the rear bumper on a blanket after removal e On each side release five retaining tabs along the fenderwell RIGHT REAR FENDER 5 RETAINING TABS REAR BUMPER REAR BUMPER 2012 American Honda Motor Co Inc All Rights Reserved All 47363 1208 9 of 21 28 Remove the rear under cover three bolts 3 BOLTS REAR UNDER COVER 29 Remove the two muffler bushings from the vehicle pins NOTE Be careful not to damage the muffler Installing the Trailer Hitch 30 Loosely install the trailer hitch on the vehicle frame with six 10 mm plain washers six 10 mm spring washers and six 10 x 40 mm hex bolts VEHICLE FRAME Ww 6 PLAIN 5 TRAILER sia mm HITCH 6 SPRING WASHERS 10 mm 6 HEX BOLTS 10 x 40 mm Loosely install 31 Loosely install the center plate to the trailer hitch with two 12 mm plain washers one 12 mm spring washer one 12 mm hex nut and one 12 x 50 mm BUSHING hex bolt through the tow hook TRAILER HITCH FRONT BUSHING MUFFLER HEX BOLT 12 50 mm Loosely install PLAIN HEX NUT HOOK WASHER 12mm prine PLAIN WASHER WASHER CENTER 10 of 21 All 47363 1208 2012 American Honda Motor Co Inc All Rights Reserved 32 Tighten the bolts to the specified torque in the order of 1 and 2 Torque the 10 x 40 mm hex bolts to 46 N m 34 lbf ft
15. unit harness as shown and secure it to the vehicle panel with connector clip installed in step 67 69 Secure the clip on the trailer unit harness to the vehicle panel as shown 2012 American Honda Motor Co Inc All Rights Reserved All 47363 1208 Using pushpin pierce the center of the scribe mark on the left rear side trim panel NOTE Some left rear side trim panels may not have the scribe line If not use the measurement shown LEFT REAR SIDE TRIM PANEL SCRIBE MARK 3mm DRILL BIT 20 mm HOLE SAW While wearing an eye protection drill the mark on the left rear side trim panel with a 3 mm drill bit Enlarge the 3 mm hole to 20 mm using 20 mm hole saw Using a utility knife cut the left rear side trim panel along the scribe line as shown Remove any burrs aA KNIFE LEFT REAR SIDE TRIM PANEL BSN Cut off SCRIBE LINE 19 of 21 73 Under the dashboard install the 7 5A fuse into the 76 fuse box as shown FRONT VIEW FUSE Plug in here FUSE BOX 7 5A FUSE 77 74 With the help of an assistant reinstall the rear under 78 cover and the rear bumper j HITCH PIN TRAILER HITCH 79 80 81 82 HITCH PIN CLIP 83 HITCH PIN BALL MOUNT 75 Secure the ball mount to the trailer hitch with the hitch pin and hitch pin clip 20 of 21 All 47363 1208 Remove and discar
Download Pdf Manuals
Related Search