Installation Instructions
Contents
1. mark resulting from this installation p gt TA REMOVE THESE FASTENERS Er RAISED CIRCLES ON STEP 4 Following the instructions on the template mark and drill the appropriate Ba im 2 161 Hola a holes using a 7 16 drill bit The middle hole on the left side must be drilled for installation of the wiring RIGHT SIDE TEMPLATE STEP 5 Feed the wiring though the left spoiler foot Install the spoiler feet to the spoiler assembly using the 1 4 20 x 5 8 Socket Head Cap Screws Tighten securely PIC 3 STEP 6 Feed the wires through the rubber pad for the left foot Place the rubber pads in place on the feet STEP 7 Feed the wires from the Spoiler through the center hole on the left side of the trunk lid Line up the holes in the trunk lid with those in the spoiler feet Using the 1 4 20 x 9 16 Button Socket Cap Screws and 1 4 flat washers fasten the Spoiler to the trunk lid securely ROUTE WIRES THROUGH LEFT SPOILER FOOT NOTICE It is the installer s responsibility to ensure that all of the fasteners r including pre assembled are tightened before operation of the motorcycle Kuryakyn will not issue a warranty on components lost due to improper installation Periodic maintenance may be required v PIC 4 ROUTE HARNESS SS THROUGH HERE SSS i Jon 12 MODELS A STEP 8 Remove the seat passenger backrest and the rear fender panel as outlined in the service manual NOTE Older models may ha2. INSTALLATION CHROME LOW PROFILE SPOILER 3239 PARTS INCLUDED CUSTOMER SERVICE 1 Low Profile Spoiler Assembly with Run Turn Brake L E D INSTALLATION QUESTIONS 2 Low Profile Spoiler Bases ea eas 1 Hardware Kit Containing 4 1 4 20 x 9 16 Button Socket Cap Screws ee LIMITED WARRANTY 4 1 4 20 x 5 8 Socket Head Cap Screws Oe a ae 4 1 4 Flat Washers 2 Anti Seize Packets 1 Wiring Kit Containing 1 55 Five Female Bullet to Six Pin Connector Wire Harness e K 1 01 10 Rear Accessory Wiring Adapter 1 Double Y Connector 6 Cable Ties i 2 Dielectric Grease Packets 1 Template Set 1 Installation Instructions gitar mak Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING K RYAKYN ee so E a IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS WARNINGS CAUTIONS AND NOTICES REGARDING THE USE AND CARE OF THIS PRODUCT i THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY This indication alerts you to the fact that ignoring the N OT CE contents described herein may negatively affect product performance and functionality NOTICE IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY eKiiryaky PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE sepia INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF THE IMPORTANT INFORMAT
3. ION CONTAINED IN THEM TOOLS SUGGESTED Set of Metric and Standard Hex Wrenches Drill and Drill Bits ABOUT OUR CATALOG STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS STEP 1 Read and understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface and turn off the ignition NOTE On 12 GL 1800 s this product requires previous installation of Kuryakyn Rear Accessory Plug and Play Harness P N 3230 NOTE Not all of the included wiring adapters will be used on all installations 3239 22GL 0512 cont K Cr VaKpN i A factory service manual may be helpful in performing this 0 gia E installation DO NOT attempt to perform this installation if you ar are not confident in your ability to complete all of the steps in f 7 e the procedure consult a trained technician STEP 2 Open the trunk lid Remove all fasteners holding the inner trunk panel to the trunk lid PIC 1 STEP 3 Using the templates provided locate the ejector pin marks raised circles ee a 3 and place the template over the pin marks in the trunk The templates are labeled for the left and right sitting on the bike side PIC 2 NOTICE MEASURE TWICE DRILL ONCE Double check all reference aia marks made on the Trunk Lid BEFORE drilling K ryakyn will not be responsible for incidental or consequential damages Ejector pin
4. h the BLACK and WHITE wires in to the male and female ends The sub harness acts like a t harness and will go between the stock blue plugs STEP 15 You should have one six pin connector left Plug the six pin connector from the Spoiler Harness into it If you plan on adding other K ryakyn Accessory lighting to the rear of the motorcycle you may install the included Double Y Connector to the six pin connector first then connect the Spoiler harness to it or store the Double Y Connector for future use ALL MODELS STEP 16 Turn the bike on and check that all lights function correctly A WARNING ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS A LIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY CONNECT TO BLUE i CONNECT TO RED MALE AND ai MALE AND FEMALE FEMALE PLUGS STEP 17 Use the included cable ties to secure the wiring out of harms way Re install the inner trunk lid removed in Step 2 Replace the rear fender panel and seat if removed Securely tighten all fasteners A WARNING AFTER INSTALLING THE SEAT PULL UP ON IT TO ENSURE IT IS LOCKED N i A INTO PLACE A LOOSE SEAT CAN SHIFT AND CAUSE oaii LOSS OF CONTROL CONNECT TO BLUE RESULTING IN SERIOUS ene INJURY OR DEATH SINGLE ORANGE WIRE 7 Secure all wiring away from any moving parts pinch points or extreme heat NOTICE Kuryakyn WILL NOT issue a warranty on any e
5. lectrical component that fails due to pinched crimped broken abraded melted or frayed wires NOTICE It is the installer s responsibility to ensure that all of the fasteners including preassembled are tightened before operation of the motorcycle Kuryakyn will not issue a warranty on components lost due to improper installation Periodic maintenance may be required PAGE li y ao E n A 7 E j g d ia A CHROME LOW PROFILE SPOILER INSTALLATION
6. ness 55 Five Female Bullet to Six Pin Connector harness to the wire Secure the wire tight enough that it will ROUTE HARNESS not come undone in the routing process Pull the wire or coat hanger back toward ALONG THIS HARNESS 7 the front with the wires still secured to it Once the wires are pulled far enough to OPN TRUNK reach they can be removed from the wire coat hanger Route the five female SHOWN bullet connector end of the Harness along the trunk wire harness to the five male bullet connectors from the Spoiler PIC 7 Use the included cable ties to secure the harness out of harms way Connect the five female Bullet connectors to the wiring placed through the left spoiler foot in Step 5 PIC 8 Make sure to push the connectors together far enough so all the metal of each connector is inside the plastic insulating sleeve Match the colors The functions of each wire color are ROUTE HARNESS ALONG THIS HARNESS ON 01 10 MODELS LEFT SIDE UNDER Yellow Right Turn Black Run Red Brake irre SEAT Green Ground White Left Turn Locate the Female Six Pin Connector on the Rear Plug and Play Harness P N 3230 or an open female six pin connector on a Y Adapter connected to the Rear Plug and Play Harness Plug the male six pin connector of the Low Profile Spoiler into the female six pin connector If there are no open connectors unplug the six pin connector from the Rear Plug and Play Harne
7. ss connect the included Double Y Connector to the Plug and Play harness Then connect the spoiler and other accessories in line to the Double Y connector Use the included cable ties to secure the wire harness out of harms way Proceed to Step 16 ALONG THIS HARNESS ON 01 10 MODELS LEFT SIDE OF OPEN TRUNK SHOWN your motorcycle unplug either end of the current wiring adapter installed and plug the new Rear Accessory Light Adapter in line with it using the following Steps PIC 9 On the bike disconnect the red plug that has an orange wire PIC 10 Take the supplied 01 10 Rear Accessory Wiring Adapter harness PIC 11 connect the male and female plug 3 wire plug with a single ORANGE wire running to it into the disconnected stock red male and female plugs The sub harness acts like a t harness and will go between the stock PAGE red plugs 3 CHROME LOW PROFILE SPOILER INSTALLATION ee STEP 13 On the bike disconnect the blue connector that has a light blue wire PIC 10 Take the supplied Kuryakyn harness connect the male and female plug 3 wire plug with the RED and BLUE Bice Ws PIC 9 wires into the disconnected stock blue male and female plugs The sub harness acts like a t harness and will go between the stock blue plugs ae p DIE STEP 14 Locate the blue connecter on the bike that has the green wires PIC 10 Disconnect it and place the two pin connector wit
8. ve one fastener behind the license plate RIGHT SIDE UNDER PASSENGER SEAT SHOWN PAGE cont 2 CHROME LOW PROFILE SPOILER INSTALLATION STEP 9 NOTICE Kuryakyn recommends the use of dielectric grease on electrical connections STEP 10 CONNECTING WIRING 12 GL 1800 NOTICE Kuryakyn recommends the use of dielectric grease on electrical connections STEP 11 CONNECTING WIRING 01 10 GL 1800 NOTICE K ryakyn recommends the use of dielectric grease on electrical connections NOTE If you already have K ryakyn Rear Accessory lights on the back of STEP 12 cont ee On 12 models Route the six pin connector on the end of the 55 Five Female Bullet to Six Pin Kuryakyn Connector harness under the seat and along the main harness along the frame on the RIGHT side of the motorcycle PIC 4 to the rear of the motorcycle It may PIC 5 Ee be helpful to use a guide wire Route the five female bullet connector end of the kessi Harness along the trunk wire harness to the five male bullet connectors from the Spoiler PIC 5 Use the included cable ties to secure the harness out of harms way On 01 10 models Take a piece of wire or a straight coat hanger to pull the wire through and run it along the inside of the left frame rail PIC 6 until you can reach it from the back of the bike The wire should come out to the top left of the inside back panel Tape the bullet ends of the har
Download Pdf Manuals
Related Search