SP-100 - Frank`s Hospital Workshop
Contents
1. No Partsnumber Parts Name Remarks 4 C81 0058 Spacer brass 5 Screw with spring washer M3 6 6 792 M321 Main unit base process2 lt Page 12 gt 12 Service Manual HANDY PACHYMETER SP 100 Doc No A Remove 2 Tapping screw and remove 1 Thermal printer B Remove 2 Screw with spring washer C Melt soldering part between 4 Connector Assy and 6 Main board and remove 4 Connector Assy aA maa I I i 13 Service Manual HANDY PACHYMETER SP 100 Doc No Assembly 792 M321 Main unit base Process2 No Partsnumber Parts Name Remarks 1 E20 0026 Thermal printer MTP102 16B 2 Tapping screw M2 3 4 3 792 M331 Main unit base process1 Assembly 792 M331 Main unit base Process1 No Parts number Parts Name Remarks 4 792 M501 Connector Assy 5 Screw with spring washer M3 6 6 792 010A Main board lt Page 14 gt 14 Service Manual HANDY PACHYMETER SP 100 Doc No A Remove 4 Screws from 2 Bracket LCD B Remove 1 Frame LCD and 3 LCD lt Page 15 gt Service Manual HANDY PACHYMETER SP 100 Doc No Assembly 792 M401 LCD Assy No Partsnumber Parts Name Remarks 1 792 2004 Frame LCD2. 2 792 2005 Bracket LCD 3 E02 0022 LCD ETMG240160D 05 4 Screws 5 Spring washer lt Page 16 gt 16 Service Manual HANDY PACHYMETER SP 100 Doc No Assembly 792 M501 Connector Assy No Partsnumber Parts Name Remarks 1 792 2003 Bracket probe connector 2 F22 0023 Ferrite core 3 792 040A Probe harness lt Page 18 gt 18 Service HANDY PACHYMETER SP 100 Manual Doc No 4 Wiring Diagram LCD E20 0026 Main board 792 010A Membrane Switch PP T92 021A FOR Thermal Printer E20 0026 lt Page 19 gt o RS 232C a Lithium ion Battery FA0 0003 AC Adapter E31 0001 100V E31 0002 230V E31 0003 120V 19 Service Manual HANDY PACHYMETER SP 100 Doc No 5 Voltage in connector Main board 792 010A Connector No Pin No Cord Color Output Note CN7 1 7V 2 GND 3 GND CN8 1 Red 3 7V Lithium ion battery 2 Black GND Lithium ion battery lt Page 22 gt 20
3. SP 100 Service Manual 2004 Aug 02 Ze TOMEY CORPORATION Service Manual HANDY PACHYMETER SP 100 Doc No 1 Caution for maintenance and Service Please take care below points when you do Service and Maintenance 1 Service and Maintenance should be done under safety condition Before you do any Service and Maintenance you must check power and unit condition to take You must do any Service and Maintenance following this manual with proper tool 2 Service and Maintenance must be done correctly We use some tube and insulating tape to hold some connector and harness in order to avoid falling down and short circuit So you have to put back as same as initial condition When you ask repair to TOMEY please inform detail condition and symptoms And if you change some setting please put back it as same as initial condition 3 After you finish Service and Maintenance you must check safety and function Please check all screws and connectors are put back as same as initial condition And check some scrap iron does not remain inside of board After you finish repair please check function lt Page gt Service Manual HANDY PACHYMETER SP 100 Doc No 2 Trouble shooting No Symptoms Page 1 LCD does not illuminated when power switch turns ON 3 2 Nothing is displayed on LCD 3 3 Cannot measure with human eye and model eye 4 4 Measurement data is not printed ou
4. ervice HANDY PACHYMETER SP 100 Doc No Manual A Remove 2 Window LCD and 3 Window light diffusion B Remove 4 Mirror reflect and 5 Membrane switch that is attached on 1 Cover front by two sided tape carefully Remove 6 Tapping screw and remove 7 Printer cutter Q lt Page 9 gt Service Manual HANDY PACHYMETER SP 100 Doc No Assembly 792 M101 Front cover Assy No Partsnumber Parts Name Remarks 1 792 1001 Cover front 2 792 1008 Window LCD 3 792 1005 Window light diffusion 4 792 1006 Mirror reflect 5 792 021A Membrane switch 6 Tapping screw M2 3 7 248 6014 Printer cutter lt Page 10 gt 10 Doc No HANDY PACHYMETER SP 100 Service Manual Note You have to take care when you remove Flexible Printed Circuit of LCD A Remove 3 Screws with spring washer and remove 1 LCD Assy B Remove 5 Screw with spring washer and remove 4 Spacer lt Page 11 gt 11 Service HANDY PACHYMETER SP 100 Doc No Manual Assembly 792 M301 Main unit base Process4 No Parts number Parts Name Remarks 1 792 M401 LCD Assy 2 792 M311 Main unit base process3 3 Screw with spring washer M3 6 Assembly 792 M311 Main unit base Process3
5. on of Pachy probe Cause4 Probe angle Countermeasure gt gt When you measure human eye or model eye you have to keep vertical against for eyeball or test piece Cause6 Defective Main board Countermeasure gt gt Check the Main board 792 010A and if there is a problem replace Main board 4 Measurement data is not printed out Cause1 Paper jamming Countermeasure gt gt Check the condition of paper If it is jamming remove jamming paper from outlet side and set paper in correct position Cause2 Defective Membrane switch Countermeasure gt gt Check the Membrane switch 792 0214 If it is broken replace Membrane switch Cause3 Defective Printer Countermeasure gt gt Check the Thermal printer E20 0026 If it is broken replace Thermal printer lt Page 4 gt Service HANDY PACHYMETER SP 100 Doc No Manual 3 Parts Parts list and How to disassemble A Open 1 Cover printer and remove 2 Printer Paper Note When you remove printer paper it should not be pulled from inlet part It will hart printer and be cause of defection of printer You should cut printer paper from inlet part and pull remains from outlet side B Remove 1 Cover printer with pushing support part toward to inside C Remove 3 Stand rear with pushing support part toward to out side D Remove 4 Self binding screw and remove 5 Battery cover Assy E Remove 6 Li
6. t 4 lt Page2 gt Service Manual HANDY PACHYMETER SP 100 Doc No 3 Countermeasure 1 LCD does not illuminated when power switch turns ON Cause1 Low power of Lithium ion buttery Countermeasure gt gt Check the power of buttery If it is low connect AC adopter Cause2 Incorrect connection Countermeasure gt gt Check the connection of all harness that is connected to Main board 792 010A Cause3 Defective Main board Countermeasure gt gt Replace Main board 792 01 0A Cause4 Defective LCD Countermeasure gt gt Replace LCD E20 0026 2 Nothing is displayed on monitor Cause Brightness control volume is turn to minimum Countermeasure gt gt Adjust this volume Cause2 Incorrect connection of LCD Countermeasure gt gt Check the connection between LCD E02 0022 and Min board 792 010A Cause3 Defective LCD Countermeasure gt gt Replace LCD E02 0022 lt Page 3 gt Service Manual HANDY PACHYMETER SP 100 Doc No 3 Cannot measure with human eye and model eye Cause Machine does not go measurement mode Countermeasure gt gt Select measurement mode and then start measurement Cause2 Broken Pachy probe Countermeasure gt gt Check the condition of Pachy probe If problem still remain replace Pachy probe Cause3 Incorrect connections of Pachy probe Countermeasure gt gt Check the connecti
7. thium ion battery with pulling connector part Don t pull harness F Remove 7 Dust cap lt Page 5 gt Service Manual HANDY PACHYMETER SP 100 Doc No Assembly 792 M001 Assy SP 100 No Partsnumber Parts Name Remarks 1 792 1003 Cover printer 2 C70 0004 Printer paper 3 792 1004 Stand rear 4 Self binding screw M3 6 5 792 M601 Battery cover Assy 6 FA0 0003 Lithium ion battery 7 C77 0012 Dust cap Hirose DE 9S DC1 lt Page 6 gt Doc No Service HANDY PACHYMETER SP 100 Manual A Remove 1 Screws and remove 2 Rear cover Assy B Remove 4 Screws with spring washer that hold ground cable ALPET connected to 3 Front cover Assy C Remove connector of Membrane switch from connector of 5 Main base process3 lt Page 7 gt Service Manual HANDY PACHYMETER SP 100 Doc No Assembly 792 M011 Main unit Sub Assy No Parts number Parts Name Remarks 1 Screws M3 8 2 792 M201 Rear cover Assy 3 792 M101 Front cover Assy 4 Screws with spring washer M3 6 5 792 M301 Main unit base process 4 Assembly 792 M201 Rear cover Assy No Partsnumber Parts Name Remarks 6 792 1002 Cover Rear 7 792 1009 Foot rubber lt Page 8 gt S
Download Pdf Manuals
Related Search