Installation Instructions Truckin Suspension 6.5” Suspension Lift Kit
Contents
1. lik eCKil as SUSPENSION COM Installation Instructions Truckin Suspension 6 5 Suspension Lift Kit 1997 1999 DODGE DAKOTA DURANGO worm and sector Important Read all instructions before attempting any work on the vehicle DO NOT DISSASSEMBLE ANY PART OF VEHICLE PRIOR TO COMPARING THE DELIVERED PARTS AND THE INCLUDED PARTS LIST REPORT ANY DISCREPENCIES IMMEIDATELY TO 800 775 7150 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering Important Read all instructions before attempting any work on the vehicle DO NOT DISSASSEMBLE ANY PART OF VEHICLE PRIOR TO COMPARING THE DELIVERED PARTS AND THE INCLUDED PARTS LIST REPORT ANY DISCREPENCIES IMMEIDATELY TO 800 775 7150 Disclaimer Notice Installing this suspension system on any vehicle implies that you are in agreement with the following terms and conditions with respect to that vehicle the vehicle owner and any or all occupants of said vehicle at any time Truckin Suspension is not responsible and cannot be held responsible for any conditions of said vehicle including but not limited to the following 1 Any and all adverse behavior premature failure or breakage caused by oversized tires and wheels improper installation failure to follow instructions or any general negligence caused by installer or owner of said vehicle 2 Any breakage or premature failure caused by racing or driver negligence 3 ANY incident determined to be caused by an increas2. 14 15 16 17 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering Using a grinder clean area so frame is smooth Hang upper a arm drop down brackets using 2 2 x 1 2 bolts washers and crimp nuts drill 1 2 holes into inner side of rear a arm pockets using the bracket to locate and use 12 x1 12 bolts washers and crimp nuts to attach a arm drop bracket ear to inner side of rear a arm pocket and TIGHTEN Hang front lower a arm drop brackets through front frame cross member insert bolts into front cross member and down through drop brackets with 3 4 inch spacer provided in kit put 2 washer and 12 crimp nuts on bolts do not tighten Install front lower a arm cross member between front lower a arm drop brackets using 7 16 x 1 1 4 bolts washers and crimp nuts 4 bolts are for the front and 2 are for the middle rear bolt holes and hand tighten Install drop drag link and tighten with new cotter pins Install rear lower a arm drop down cross member install pancake bumpstops to top of rear cross member and soft cushion bumpstops to lower part of cross member HAND TIGHTEN When tightening lower a arm cross member be sure that the new lower a arm mount bolt holes are exactly 6 5 on center from the original lower a arm mount bolt holes TIGHTEN CROSSMEMBER Page 6 18 19 20 21 22 23 24 25 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering Be sure that fro
3. Specifications Remember that actual torque may vary if lubricant is used or extension bars are used with the torque wrench Torque all re used O E factory hardware to original vehicle torque specifications according to factory service manual If in doubt concerning the torque specification of ANY fastener always consult the factory service manual Always consult factory service manual for sequence and torque specification of any O E parts being reassembled such as ball joint nuts and steering tie rod ends For hardware supplied with this kit use the following list as a guide for fastener torque Bolt Size 5 16 12 15 Ft Ibs 8 8 3 8 Important Maintenance Information It is the end user s responsibility to have all fasteners checked for proper torque after the first 200 miles then every 3000 miles Have a qualified professional mechanic or alignment specialist inspect the steering Suspension and driveline components immediately after installation and at regular intervals thereafter Important Please read all instructions before attempting any work on the vehicle DO NOT DISSASSEMBLE ANY PART OF VEHICLE PRIOR TO COMPARING THE DELIVERED PARTS AND THE INCLUDED PARTS LIST REPORT ANY DISCREPENCIES IMMEIDATELY TO 800 775 7150 Failure to read entire instruction packet before beginning disassembly will likely result in additional downtime spent acquiring tools special equipment and skilled mechanical know how We strongly reco
4. d in kit 5 Reinstall front of springs with factory hardware 6 Remove rear shackle invert and flip then reinstall with factory hardware to new rear spring hanger 7 Mount new e brake bracket to frame with supplied hardware You must drill 1 2 inch hole in fame 8 Loosen but to not remove U bolts holding rear springs to the axle Retighten This is to relieve any bind in the leaf springs Page 8 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering 9 Remove brake line from bracket inside of frame on driver s side and install new bracket supplied with kit Bend ears on bracket to hold brake line 10 Install sway bar extensions with factory hardware 11 Install new shocks 12 Install wheels and place vehicle on the ground Torque lower control arm pivot bolts with the vehicle resting on the ground CHECK ALL FLEXIBLE BRAKE LINES making sure they are clear of moving parts when the suspension cycles up and down Make preliminary adjustments to camber and toe in as needed to get front wheels visually straight Recheck all fasteners and components again to make sure everything is tight REMEMBER TO TORQUE THE LUG NUTS Reconnect battery 13 Test drive vehicle at speed and listen for noises Drive vehicle in different conditions while turning in drive and reverse to check tire clearance and trim plastic bumper valance if necessary Engage 4WD in low and high Have a QUALIFIED ALIGNMENT SPECIALTY SHOP reset the
5. e height in said vehicle s center of gravity 4 ANY incident determined to be caused by improper installation 5 ANY incident determined to be caused by a failure of materials Truckin Suspension is to be held harmless by the installer of this lift kit owner of said vehicle ANY occupants of said vehicle and any parties related directly or indirectly to said vehicle or owner of said vehicle Truckin Suspension is to be held harmless by all parties mentioned during the course of any and all circumstances or incidence resulting from the installation of this lift kit Truckin Suspension offers this kit strictly as a visual improvement of said vehicle over the factory aesthetics The fact that the suspension system works and functions well is incidental and it is not the intention of Truckin Suspension that said vehicle be modified for use on public highways sanctioned by the Department of Transportation or any state or local governing body Vehicle owner accepts sole responsibility for ensuring that said vehicle is not in violation of local state or federal laws or vehicle code Please check local vehicle laws and regulations before modifying your vehicle By Installing This Kit or having this kit installed on your vehicle you are implying that you agree to the above terms and conditions Please do not install this system if you do not agree Page 2 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering Kit Hardware Torque
6. front end alignment to correct specification DO NOT drive vehicle more than 15 miles before having the alignment checked by a qualified shop Re torque wheels after 200 miles and recheck all lift kit hardware after 3000 miles Page 9
7. mmend installation be done by a professional mechanic in a shop with a suitable vehicle hoist If attempting this installation as a do it yourselfer please review this packet carefully BEFORE attempting any work on the vehicle A well equipped shop can perform this installation in approximately 12 hours This packet uses standard nomenclature when referring to each side of the vehicle LEFT side means DRIVER S side while RIGHT side means PASSENGER side Page 3 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering Required Tools and Equipment Make sure all of these tools and equipment are readily available BEFORE beginning work on the vehicle Good quality safety glasses and ear protection Professional Quality Floor Jack or vehicle hoist Tall Jack Stands 4 2 drive Socket set and ratchets with metric standard and deep sockets 3 8 drive Socket set and ratchets with metric standard and deep sockets Hex Sockets recommended OR Allen wrench hex key set Compressor w impact wrench and air ratchet recommended Air hammer with flat pointed chisel and shovel tip chisel bits Pickle fork type tie rod separator and ball joint separator Torsion bar unloading tool recommended OR 2 jaw gear puller Transmission Jack recommended Plasma Torch recommended OR Sawzall with metal cutting blades MIG or equivalent wire feed welder with 75 25 Argon or better 4 grinder recommended or chisels and files 2 drill mot
8. nt lower a arm drop downs are perpendicular to the ground and that all suspension is square when tightening hardware Install lower a arm in to new mounts Hand tighten Install the cv axles Install upper a arm to new bracket Hand tighten To install new torsion bar cross member you will need to draw a straight line from center of old cross member to bottom of frame center cross member drop down brackets and drill 2 Y2 holes up into lower frame rails install drop down brackets and new torsion bar cross member using 12 x 1 2 bolts washers and crimp nuts Reinstall torsion bars Reload torsion bars to factory specs Tighten all hardware in order Front lower crossmember lower a arms upper a arms tie rods for steering Using the 2 aluminum sway bar blocks and the new sway bar bushings and 3 8 x2 1 4 bolts washers and lock nuts install sway bar to rear of front lower a arm drop down brackets the aluminum blocks are drilled to go over the 2 rear 7 16 bolts already installed Install new bushings and tighten to frame and lower a arm Page 7 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering INSTALLING REAR KIT 1 Remove clips from old brake line bracket located on inside of frame 2 Remove factory shocks and sway bar end links DO NOT UNDO WITHOUT REAR END BEING SUPPORTED 3 Cut off rivets of old front and rear hangers to remove leaf springs 4 Bolt on new hangers with 7 16 inch bolts supplie
9. or and drill index 2 and 34 drill bits required Dead blow hammer recommended OR suitable ball peen hammer Soft face hammer Screwdrivers Pliers and Channel Locks Side cutter type cutting pliers Pointed Heel bars recommended OR pry bars Cotter pin assortment Tie wire and or plastic zip ties DO NOT attempt installation unless you have everything on this list or suitable substitutes for the recommended tools Page 4 6 5 Suspension Lift Kit 97 99 Dakota with Worm and Sector Steering Installing Front Kit 1 2 11 Disconnect Battery Remove upper shock nut and bushing Remove wheels when vehicle is properly lifted from the ground and secure from frame rails with jack stands Release tension from torsion bars and remove tapping out roll pins in control arm Remove brake calipers and tie up off front of frame Don t allow brakes to hang from brake lines Remove sway bar from under lower control arms Remove CV axles spindles upper and lower control arms Unbolt front drive line from front differential and tie up to frame Unbolt drag link and remove Remove crossmember under differential Support differential with jack and remove four mounting brackets Replace with four new brackets supplied with kit and tighten Using a high speed cut off or sawzall cut and remove droop bump stop from both driver and passengers side of frame rails for new upper arm mount _ y e mg k Page 5 12 13
Download Pdf Manuals
Related Search