screamin` eagle pro stage ii performance kit - Harley
Contents
1. cMOTOR HARLEY DAVIDSON WY J04779 INSTRUCTIONS REV 2011 06 06 SCREAMIN EAGLE PRO STAGE II PERFORMANCE KIT GENERAL Kit Number 30076 09 Models This kit is designed to fit 2008 and later V Rod model motor cycles NOTE The kit is intended for High Performance applications only Engine related performance parts are intended for the experi enced rider only Additional Parts Required Valve shims see a Harley Davidson dealer for selection Shims 1 825mm through 3 000mm available from a Harley Davidson dealer Shims larger than 3 000mm available from sources like www hotcamsinc com SuperTuner recalibration for the ECM See a Harley Davidson Dealer for your model year Each service manual or supplement procedure will require special tools These tools are called out in the service manual or supplement and are available through the SPX Kent Moore Special Service Tools catalog AWARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet references service manual information A service manual for your model motorcycle is required for this installation and is available from a Harley Dav2. ce manual procedure to time the cams to the cam drive 6 Follow service manual procedures to verify the valve lash 7 f required use a copy of the Valve Lash Calculation Worksheet found in the Appendix of the service manual Adjust the valve lash following service manual MAINTEN ANCE VALVE LASH Verify Cam Timing and Lash Adjustment 8 After verifying lash adjustment install and tighten spark plugs to 17 ft lbs 23 Nm 1 of2 Optional Airbox Modifications 1 Using service manual instructions remove the airbox assembly After removing the intake air temperature sensor IAT and grommet discard the airbox top cover 2 Using the right left and front side airbox templates see last page for templates lay a template in place and prick punch the center of the crosshairs Use a 1 inch hole saw to drill the larger holes and a 17 82 inch drill bit for the IAT hole 3 Clean lower airbox and install the airbox assembly velocity stacks air filter and cover according to service manual instructions 4 Install IAT grommet and IAT to the airbox and connect the IAT harness Return the Motorcycle to Service 1 Install the main fuse and the right side cover 2 Reconnect the battery positive cable first NOTE Calibration can be supplied through any authorized Harley Davidson dealer 3 Before starting the engine recalibrate the ECM NOTICE When closing the seat make sure the ignition switch is in the FUEL
3. idson Dealer NOTICE You must recalibrate the ECM when installing this kit Failure to properly recalibrate the ECM can result in severe engine damage 00399b ECM recalibration is required using a SuperTuner Motorcycle must not be started until the recalibration is done See a Harley Davidson dealer Kit Contents See Figure 1 and Table 1 J04779 Prepare the Motorcycle for Service INN NIN To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 1 Remove the right side cover and the main fuse 2 Follow service manual instructions to remove the airbox assembly 3 Disconnect the battery negative cable first INSTALLATION NOTES The cam removal and installation procedure does not require the removal of the engine from the frame Follow the service manual valve lash procedures in the VRSC service manual Valve lash specifications will be found in the engine specifica tions section 1 Follow the service manual valve lash procedure to repos ition the engine in the chassis NOTICE Rotate engine toward front cylinder only Do not rotate engine toward rear cylinder as engine damage can result 00409c 2 Remove the cams per the service manual procedure for adjusting the valve lash 3 Install the new cams and check valve lash per service manual procedure 4 Complete assembly per valve lash procedure 5 Follow servi
4. position If the ignition switch is in any other position when the seat is closed the seat latch mechanism could be damaged 00196a 4 Close the seat WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b Test Run Motorcycle 1 Test start engine If the oil pressure indicator lamp illumin ates follow the service manual procedure to troubleshoot the problem 2 If there is a rattle heard during engine start up follow service manual procedure to adjust the secondary cam chain J04779 SERVICE PARTS is06246a Figure 1 Service Parts VRSC STAGE Il PERFORMANCE KIT Table 1 Service Parts Item Description Quantity Part Number 1 Camshaft assembly intake 2 17470 09 2 Camshaft assembly exhaust 2 17473 09 3 Air filter element 29793 02C 4 Front velocity stack 30078 09 5 Rear velocity stack 30079 09 6 Cam cover gasket kit not 17010 01K shown 7 Lower airbox drill templates 3 Not Sold Separately Items mentioned in text but not included in kit A Lower airbox shown with template holes drilled B Air filter element cover 2 of 2
Download Pdf Manuals
Related Search