650227f MCL-3006 SPD_MilesToEmpty_
Contents
1. Press and hold the switch for about six seconds to reset the high rpm recall while it is displayed The tachometer only has two display modes as follows TACH MENU CLOCK gt 2 00 12 hour clock HI RPM ugg high rpm recall GAUGE SETUP AND CALIBRATION The function switch discussed above is used to enter setup mode for all of the gauges The first step in the setup procedure is to select which gauge you are going to select to change a setting Each gauge will either show a number or a label If the gauge is showing a label then that gauge will be selected to enter setup All of the other gauges will exit setup and allow the selected gauge to be changed To get into setup press and hold the function switch while turning the key on Press and release the switch to advance through the menus below when on the desired option press and hold the switch to select setup for that particular gauge function speed tach loilpsi oiltemp Fuel volt Lea Le Ene N ru ru ru 1 Lui Lui Lut iN 5 KA EE O m N ST m m T TO c rc IT Paman Co CO FACTORY DEFAULT SETTINGS FOR SETUP MENUS Below is a list of all of the factory gauge settings and what can be adjusted in the setup menus You can calibrate and adjust gauges as often as you wish however they should only need to be set once Most gauges will function properl2. Use zip ties to secure the wire harness to the other wires along the frame Once you have the wires up through the battery box area it is recommended you remove the tank bolts to continue running the harness under the tank Use a firm wire and some electrical tape to fish the wires up the backbone under the tank filler rod welding wire works well for a fish tape Once clear of the tank follow the factory wiring harness on the right side and route wires behind the fairing and over to the oil temp gauge Make sure to replace and tighten the tank bolts when done If you are going to be routing a new ground wire for the fuel gauge it should be routed under the tank at the same time as the oil temperature harness to ease installation y Remove rear tank bolt Remove front tank bolts to loosen tank 6 MAN 650227 E Pull the temp sensor wires through the fairing Route wires under tank Now you will have to de pin a couple wires to connect the temp sensor wires to the factory plug to allow a factory style plug in connection to the gauge The pins in the connector have a small locking tab on the back flat side of the terminal seen in the picture below Use a small allen wrench pick or small screw driver to bend and release this tab While pushing on the tab pull the wire gently out from the back of the connector You will need to remove Black pin2 gauge ground bottom center location in the housing Blue w Violet pin3 gauge sig
3. and air temp have two plugs One is for illumination the other is for the gauge power ground and sensor The illumination harness two pins orange and black wires will not be reused and can hang freely inside the fairing with the bulb removed or can be secured to the other gauge wires to clean things up The three pin connector will be used to connect all of the new Dakota Digital small round gauges Unplug connectors at the back of the four small round gauges then remove the two 5 16 nuts holding the clamps onto each small gauge and remove the gauges New nuts for the small gauges are included in the hardware pack DO NOT reuse the stock nuts for the new gauges they are not the same thread Si Ped Remove the small gauges with 5 16 wrench or nut driver IMPORTANT NOTE SAVE ALL CLAMPS GASKETS and SCREWS FROM THE STEPS ABOVE AS THEY WILL BE USED TO SECURE THE NEW DAKOTA DIGITAL GAUGES 3 MAN 650227 E Save ALL Clamps Screws and Gaskets and reuse for install Next you are ready to install the new gauges into the fairing Install the gauges and secure using the original hardware that was removed clamps gaskets and screws Small gauges are secured using the original clamps along with the supplied nuts The picture on the first page shows the proper location for each gauge Be sure the alignment tab on the clamp lines up with the notches in the fairing Some fairings may only have one notch line up at least one tab on th
4. done in multiple trips as long as the tank is not filled in between The range display will show AnSE until this is completed and then begin showing the distance to empty e Sender is used to select the type of fuel sender and gauge being used to allow the speedometer to read the fuel level accurately 12 MAN 650227 E Speedometer Setup Continued odo Odometer preset The odometer can be preset by the customer within the first 100 miles Once the odometer has more than 100 miles the menu option will no longer be displayed Make sure you have correctly selected the units to be either MPH or km h first The odometer will be set in the selected units Once you have preset the miles you cannot change it again WARNING This only allows setting odometer to the nearest mile Do not use tenths For example a mileage of 65432 1 should be set to 65442 using this method If the tenths digit is used the odometer will read 10 times too high Press and release the switch until odai is displayed then press and hold the switch until is displayed The current miles will be displayed with the left most digit flashing Press and release the switch to increment the digit Press and hold the switch to move to the next digit to the right Continue until the right most digit has been set Press and hold the switch and the speed display will show no Press and hold the switch while no is displayed to go back and continu
5. 2 gear and drive at a steady speed Wait until the 2 goes steady and then changes to a flashing 3 Shift to 3rd gear gt Optional If the gears do not stop flashing you can manually override and jump to the next gear by pressing and releasing the switch to store the gear position quicker Repeat this through each gear When you are done come to a complete stop or press and hold the switch until the display shows dont and then release it Press and release the switch to restart the gauges in normal operation verify the gear position by riding through each gear and seeing if positions agree OIL PRESSURE SETUP The oil pressure gauge can be set for various stock Harley pressure senders There is a display update setting for how fast the numbers will change as well as a user settable low and high pressure warning points When a warning condition is reached the gauge will flash the reading as a warning indicator The stock sender for 1999 and up should be the 60 psi sender For higher pressure and more accurate pressure readings one of two Dakota Digital senders may be used 0 75 psi SEN 1032 or 0 150 psi SEN 1031 To enter setup press and hold the switch while turning the key on Release the switch The gauge will show i Press and release the switch until F5 1 is displayed then press and hold the switch until 5nd is displayed Press and release the switch until the correct sender type is displayed 4
6. WWW DAKOTADIGITAL COM MCL 3006 gauge kit Thank you for purchasing the Dakota Digital MCL 3006 gauge kit for your Harley Davidson Touring bike This kit is designed to be a direct plug in replacement for all touring models from 2004 2012 Dakota Digital also offers a kit for older models part number MCL 3000 The kit includes the following gauges and features Speed programmable speed calibration performance menu two trip meters odometer count down service miles security and check engine indicators Tachometer programmable tach clock gear position cruise control indicator ABS indicator and high rpm recall Oil Pressure programmable warning point uses stock sensor or Dakota Digital sensor for higher pressure Oil Temperature programmable warning point complete with new sensor Volts programmable warning point Fuel Level low fuel warning uses factory sensor can be programmed for custom fuel sender NOTE The factory ambient air temp gauge is replaced by an oil temperature gauge All gauges have automatic night dimming controlled by a sensor in the tachometer 000000 E 1 MAN 650227 E INSTALLATION Please read and familiarize yourself with all of the components and this manual The first step is to remove the seat and disconnect the negative side of the battery as with any electronic install Once the battery is disconnected you are ready to start Remove the outer fairing this will vary fro
7. ase the switch The display will show SL obd or FASEEr Slow will make the speedometer read lower faster will make the speedometer read higher Press and release the switch to change the selection press and hold the switch until is displayed to continue on e Release the switch The display will show CL 1 00 or whatever the current calibration ratio is e Press and release the switch to change the adjustment ratio Press and hold the switch until is displayed to save the currently displayed ratio un lk MPH km h Selection e Press and release the switch until un ik is displayed then press and hold the switch until is displayed e Release the switch The display will switch to un it and light up the current speed unit MPH or km h e Press and release the switch until the desired setting is displayed e Press and hold the switch until is displayed to the setting 5 SEt Miles to Next Service setup The service mileage is a countdown mile meter The service mile display can be disabled or can be set to count down from 500 7500 miles If the service mile is enabled and it gets to O miles it will display 5 Jl E each time the key is turned on If the push button switch is pressed and held while 45 is displayed the service miles will be reset Press and release the switch until 5 SEE is displayed then press and hold the switch until is displayed Release th
8. e changing the odometer display Turn the key off to cancel any changes e Press and release the switch to change to speed display to 465 Press and hold the switch while 425 is displayed to save the current odometer reading TACHOMETER SETUP Main Menu Sub Menu Description CL set clock time ELH n 19HE set night dimming level uPdAkE set rpm update rate for digital readout UWArn set rpm shift warning point SEAr transmission gear programming Press and hold the switch while turning the key on Release the switch Press and release the switch until CH is displayed then press and hold switch until is displayed The rpm display will show SEE and the lower display will show n ht Press and release the switch to move through the different menus press and hold the switch to select a menu option Note The tachometer calibration may require you to hold the switch while starting the bike but only if you are going to adjust set the GEAR programming since you will have to ride the bike Some ignition systems may disrupt power to other circuits when cranking causing the gauge to reset this is why you must hold the switch while starting if you are setting up the GEAR display All other gauge functions and gauges can be set without running the engine CL CLOCK SETUP The time is displayed on the smaller display below the RPM and is the first setup menu since it is the only setting that requires change once the initia
9. e clamp with the notch in the fairing this will ensure the gauges are centered and aligned correctly N Wa y Ground Speedometer and Tachometer Oil PSI Oil Temp Voltmeter and Fuel Level ee ee a a owltcn amp VIMMING S Cans _ oender WIRING plug in connections Now you are ready to make the gauge connections Plug the original soeed and tachometer connectors directly into the new gauges Plug the original oil pressure voltage and fuel connectors directly into the new gauges Because the digital fuel gauge is much more accurate than the original fuel gauge any shifts in the grounding will be more noticeable A 10 shift can be seen on the digital fuel gauge due to weak fairing ground connections that would not be noticeable with the original needle It is recommended that a new ground wire be run from the fuel gauge to the fuel sender ground on the tank Fuel ground harness 394164 is included for this purpose Instructions and photos are shown after the oil temperature sensor installation The air temperature gauge is replaced with an oil temperature gauge and this connector will need to be changed instructions on how to install and connect the sensor begin on the following page A two wire harness with six connectors is included This will plug into the back of each gauge these wires are the switch green and dim blue wires Route one of these harnesses to the back of each gauge and plug itin It does not matter which c
10. e switch The current setting will be displayed aFF or a mileage from 500 7500 in increments of 500 Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting PE F Performance Menu setup The performance readings can be turned on or off When they are turned off the odometer will only toggle through the mileage readings Press and release the switch until PErF is displayed then press and hold the switch until is displayed Release the switch The current setting will be displayed on or oFF Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting 11 MAN 650227 E Speedometer Setup Continued FuEL Fuel sender selection DEFAULT OFF This setting should be set to oFF this may be used for future accessories The options are to allow the fuel information to be introduced to the data bus This menu is not really important but is here in case future accessories require it You should not harm anything if the settings are incorrect but OFF is the default setting at this point e Press and release the switch until FuEL is displayed then press and hold the switch until is displayed e Release the switch The current setting will be displayed aFF or on e Press and release the switch until the desired setting is dis
11. easured resistance Add enough fuel to fill the tank to 1 3 Press and release the switch to save the 1 3 reading e The display will show 55 and then switch to displaying the measured resistance Add more fuel to fill the tank to 2 3 Press and release the switch to save the 2 3 reading e The display will show 99 and then switch to displaying the measured resistance Add more fuel to fill the tank full Press and release the switch to save the full reading e Press and hold until don is displayed to save the settings The gauge will then return to normal operation VOLT SETUP The volt gauge has user settable low and high voltage warning points that will make the gauge flash as a warning indicator when either of the conditions are met or exceeded e To enter setup press and hold the switch while turning the key on e Release the switch The gauge will show i e Press and release the switch until ui is displayed then press and hold the switch until Lo is displayed e Press and release the switch until the desired low voltage warning is displayed e Press and hold the switch until H is displayed then release the switch e Press and release the switch until the desired high voltage warning point is displayed e Press and hold until is displayed to save the settings Turn the key off Speedometer Troubleshooting guide Problem Possible cause Solution Gauge will not light up Orange
12. eedometer connector side of the wire to the extra short wire from the fuel gauge harness 9 MAN 650227 E FUNCTION SWITCH The factory speedometer push button switch is used as the main function switch The function switch allows access to all of the mileage rpm and performance information Pressing and releasing the function switch toggles through the different displays Pressing and holding the switch for about two seconds will reset the current display The display sequence for the speedometer is as follows SPEED MENU 000000 odometer mileage oog trip meter mileage A g 00i trip meter mileage B 5 ggg miles since last service if programmed A Speedometer will show km h or MPH if metric r 250 0 or range distance to empty if turned on PERFORMANCE MENU on speedometer when enabled Hi OO high speed recall 60 30 0 0 60 mph time G 00 0 0 100kph 29 000 quarter mile time c5 00O quarter mile speed E O00 cylinder head temp from ECM run switch must be on The 0 60 and 4 mile timers are zeroed by pressing and holding the switch while that timer is displayed The timer will not restart until the speed reaches zero and then you start driving again The function switch can also be used to change the tachometer display Make sure the speedometer is displaying the odometer to avoid resetting any of the other settings before attempting to change the tachometer Press and hold the switch for about four seconds to change the tach menu
13. f gauge is covered Make sure the lower part of the lens is not covered Gauge will not enter setup Green wire 2 wire harness is not connected Check wiring connections Green wire should have 12 volts correctly when the switch is pressed Cruise Engage indicator Loose or incorrect connection to indicator wire Check that the appropriate indicator wire has about 12 volts does not work when the indicator should be off and about O volts when the indicator should be on ECM performance tune Stock service tools look for all stock gauges Unplug MCL 3006 and reprogram ECM MCL 3006 can be or reprogramming fails plugged back in as soon as reprogramming is complete Small gauge Troubleshooting guide Problem Possible cause Solution Gauge will not light up Orange wire does not have power Connect to a location that has power check fuses Black wire is not getting a good ground Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Gauge reading is erratic or Gauge signal wire is loose or broken Check all wire connections and inspect wire for breaks jumps around Poor ground connection Check ground connection on gauge engine and sensor Gauge reading is incorrect Gauge is set up for wrong sensor type Change sensor setting in setup See instructions Poor gauge grounding Repair or replace ground wire Gauge will not dim Blue wire 2 pin harness is not connected Check wiring connections Blue wire s
14. for 96 98 stock sender 60 for 99 up stock sender 15 for Dakota Digital 75 psi 150 for Dakota Digital 150 psi Press and hold the switch until Lo is displayed then release the switch Press and release the switch until the desired low pressure warning point is displayed Press and hold the switch until H 1 is displayed then release the switch Press and release the switch until the desired high pressure warning point is displayed Press and hold the switch until SPd is displayed then release the switch Press and release the switch to change the update rate between fast F5E and slow S1 0 Press and hold until is displayed to save the settings Turn the key off OIL TEMPERATURE SETUP The oil temp gauge has a user selectable high temperature warning point that can be set so the gauge will flash the reading when the temp is met or exceeded The gauge will only read correctly with the supplied sender To enter setup press and hold the switch while turning the key on Release the switch The gauge will show Press and release the switch until F or is displayed then press and hold the switch until Sad is displayed Press and release the switch to change between Fahrenheit F and Celsius C Press and hold the switch until H 1 is displayed then release the switch Press and release the switch until the desired high temperature warning poin
15. he switch for about three seconds until is displayed Release the switch The MPH display will show SEE and the odometer display will show d 143 Press and release the switch to move through the different speedometer setup menus Press and hold the switch to select a menu option d A9 Diagnostics mode for checking clearing trouble codes e Press and release the switch until d 1H3 is displayed then press and hold the switch until is displayed e Release the switch The display will show End Ine SECurE AbS or donE e Press and release the switch to change the selection press and hold the switch until is displayed to begin reading the stored codes for the particular system e Release the switch The display will show the current codes nan or na 5P Press and release the switch to move to the next stored code After all codes are displayed the module part number will be scrolled across the screen To clear codes press and hold the switch when end is displayed Consult a service manual for trouble code descriptions AduU5k Speed Calibration The speedometer is calibrated by the engine computer but the speedometer reading can be adjusted through the gauge The adjustment is set a value from 0 75 7596 1 25 125 with 1 00 being no change e Press and release the switch until AdUu5t is displayed then press and hold the switch until is displayed e Rele
16. hould be routed under the tank with the oil temperature sensor harness Locate the three or four wire harness going to the fuel pump and fuel sender connector near the gas cap shown below The new fuel gauge ground should be attached to one of the black ground wires on this harness Three wire harnesses will have one ground wire and four wire harnesses will have two ground wires either black ground wire on the four wire harness can be used Soldering and covering with heat shrink is the preferred method for attaching the ground wire but a properly used butt connector will also work Scotch lock style connectors are not recommended Strip back the insulation on the black wire Wrap the end of the new fuel gauge harness around the exposed wire Solder the connection making sure the solder flows into the wires Wrap the splice with electrical tape to insulate it SPEEDOMETER GROUND UPDATE 2004 2007 model year only If you are using the miles to empty function on the speedometer with a 2004 2007 model year then the speedometer ground black wire will also need to be cut and connected to the newly routed fuel gauge short ground wire The original grounding on these models is not sufficient for the miles to empty function to operate correctly i H ji i IN WAN y HIDS e Locate the 12 pin connector that plugs into the back of the speedometer e Cut the black or black green wire a few inches down from the connector e Connect the sp
17. hould have 12 volts correctly when tachometer is dim Gauge remains dim at all Blue wire 2 wire harness is getting power all Check wiring connections Blue wire should have 0 volts times all of the time when tachometer is bright Gauge will not enter setup Green wire 2 wire harness is not connected Check wiring connections Green wire should have 12 volts correctly when the switch is pressed SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line In addition technical consultation is available to help you work through any questions or problems you may be having installing one of our products Please read through the Troubleshooting Guide There you will find the solution to most problems Should you ever need to send the unit back for repairs please call our technical support line 605 332 6513 to request a Return Merchandise Authorization number Package the product in a good quality box along with plenty of packing material Ship the product by UPS or insured Parcel Post Be sure to include the RMA number on the package and include a complete description of the problem with RMA number your full name and address street address preferred and a telephone number where you can be reached during the day Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase Send no money We will bill you after repair Dakota Digital 24 Month Warranty DAKOTA DIGITAL war
18. l calibrations are complete To set the clock press and hold the switch while turning the key on Release the switch The RPM display should show LL press and hold switch until is displayed Release the switch The lower display will show the current hours Press and release the switch to change the hours press and hold the switch to change to the minutes Release the switch The lower display will show the current minutes Press and release the switch to change the minutes press and hold the switch to change to the time adjust calibration Release the switch The lower display will show CAL and a number from 4 to 1 This allows the clock to be adjusted seconds per day e Press and release the switch to change the CAL value press and hold the switch to save this and exit the clock setup n 19HE NIGHT DIMMING Your display system has a dimming feature that dims the display intensity Normally the system is at full brightness for daytime viewing The tachometer has a light sensor that will provide a signal to the other gauges to reduce the brightness at night The level of darkness before the gauges dim can be adjusted in the tachometer setup Press and release the switch until n SHE is displayed then press and hold the switch until is displayed Release the switch The update setting will be displayed late darkest mid J early lightest OFF Press and release the switch until the desired setting is dis
19. m model to model please follow the service manual to expose the wiring and gauges Don t be alarmed by the amount of wires behind the fairing this is a direct plug in kit and these detailed instructions will guide you through it Pic of Street Glide with outer fairing removed Pic of Road Glide with outer fairing removed REMOVAL OF FACTORY GAUGES ULTRA FLHT amp FLHX batwing fairings Unplug the speedometer and tachometer Remove the screws securing the clamps that hold the gauges in place and pull them out through the fairing Save the screws gaskets and clamps to be reused when you install your new Dakota Digital gauges Unplug the factory speed and tach Unscrew the clamps and remove gauges ROAD GLIDE FLTR You will need to remove the speedometer and tachometer instrument bezel To do this remove two small screws on the left and right side of the bezel Lift up on the back of the bezel and slide the tab that is under the ignition switch out from under the switch cover see photos below of ignition switch cover removed to show detail Unplug the gauge connections and unplug the indicator lights so the bezel can be completely removed for easier installation of the new gauges Remove the clamps that hold the gauges to the bezel and remove the gauges and gaskets 2 MAN 650227 E ine LUY si kO Mie Se Picture of tab switch cover removed Bezel removed Gauges Grommets removed All of the small gauges fuel volts oil
20. nal old air temp sensor right location looking at back of housing Insert the RED wire into the previous location of the Blue w violet wire Insert the other BLACK wire wire with a short 3 pigtail into the black wires previous location Slide supplied piece of heat shrink over the pigtail and connect the spade connector on the black wire to the original gauge ground wire that was removed from the housing This provides ground for the gauge and sensor Heat up the heat shrink to protect the ground connection NOTE See Photos on the following page for more details 4 t Mm gt ene S i E NG a ASAP PG d a ae a o PU a hy m A E A BU ay Ka AA i j 7 E AFN 4 PAS gt We 7 ee Fee BTANA IN aag ka AAO i TO Pag Ni PA AN i pa Ber LAG NP zi l il W ie Locking tab on terminals Using a small allen pick release the locking tab 7 MAN 650227 E ia as Ser Pi ad at madag a 5 A DESTO Sa a gt p 4 Ka UM or Plug Connections Oil Temp ens 8 MAN 650227 E FUEL GAUGE GROUND UPDATE The replacement fuel gauge harness ground 394164 is included in your kit It has a long wire to go to the fuel sender and a short wire that is only used with 2004 2007 model year speedometers The factory ground wire on the fuel gauge should be removed as shown with the oil temp gauge connections on the previous page and the supplied ground wire put in its place The other end of the long ground wire s
21. onnector goes to each gauge Switch and Dim wire harness Connect one plug to the back of each gauge 4 MAN 650227 E OIL TEMPERATURE SENSOR The only small gauge that requires an additional sender is the oil temp since this is replacing the air temp gauge The supplied oil temperature sensor replaces one of the oil pan plugs You can do this at an oil change so you do not have to worry about losing oil or be quick and you should only lose a small amount of oil First locate the allen head plug on the front bottom side of the oil pan The plug is on the right of the oil pan drain plug that is used to drain the engine oil for an oil change It is a 3 8 NPT allen head plug that should be flush with the oil pan See photo for the correct plug NOTE Check oil level after install of this sensor refill oil as needed Oil Temp sensor and harness R Oil Drain Plug Bottom of oil pan Remove 3 8 npt allen plug Wipe any road grime and oil from around the plug so the area is clean Use a 5 16 allen wrench to remove the plug Have the sensor ready to thread in so minimal oil is lost Tighten the new oil temp sensor with a 34 wrench 5 MAN 650227 E Installed oil temp sensor and harness plug Plug in the sealed two pin connector and route the wires over to the bottom right side frame rail Begin running the wires back and up behind the transmission and starter area to the battery box following the wiring harness that is in place
22. played Press and hold the switch until is displayed to save the setting uPdALE Display update setup The display update will select how quickly the tachometer reading will respond Press and release the switch until ufdAre is displayed then press and hold the switch until is displayed Release the switch The update setting will be displayed slow 2 mid j fast Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting 13 MAN 650227 E Tachometer Setup Continued LJArn Rpm warning setup Press and release the switch until uJArn is displayed then press and hold the switch until is displayed Release the switch The current warning point will be displayed Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting SEAr Gear indicator setup This gauge has a single digit display for gear position The gauge can learn the gear ratios based on speed and rpm so no sensors are needed just what you ve already connected It will work with 4 5 6 or 7 speed transmissions The factory preset option will preset the indicator to work with a stock 5 or 6 speed drive train With a stock 6 speed there will be a slight delay the first time you shift to sixth gear as the system verifies the gear You can also program each gear position for afterma
23. played e Press and hold the switch until is displayed to save the setting e f an is selected then dont EESE ESEE or Adullst options will be displayed 225k shows the current fuel reading ESEE and duu5t change the fuel data sent on the bus and will not normally need to be changed e Press and release the switch until don is displayed Press and hold the switch until is displayed to exit rAn9E Distance to Empty setup The range reading will initially show the word AnSE until a tank of gas has been driven to allow the gauge to complete its setup based on your driving Begin with a full tank of gas and do not refill it until it gets below 1 4 tank of gas This can be done on multiple trios as long as no fuel is added before it gets low enough After the initial setup the display will show followed by the calculated distance to empty This will count down making adjustments as necessary until the range is 35 miles 56km or less and then it will show r Lo The gauge will continue to make adjustments to match your driving habits with each fill up After the initial setup you are not required to wait for the fuel to get below 1 4 tank before refilling e Press and release the switch until AnSE is displayed then press and hold the switch until is displayed e The display will show oFF or an Press and release the switch to change to the de
24. rants to the ORIGINAL PURCHASER of this product that should it under normal use and condition be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE such defect s will be repaired or replaced at Dakota Digital s option This warranty does not cover nor extend to damage to the vehicle s systems and does not cover removal or reinstallation of the product This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration improper installation mishandling misuse neglect or accident This Warranty is in lieu of all other expressed warranties or liabilities Any implied warranties including any implied warranty of merchantability shall be limited to the duration of this written warranty Any action for breach of any warranty hereunder including any implied warranty of merchantability must be brought within a period of 24 months from date of original purchase No person or representative is authorized to assume for Dakota Digital any liability other than expressed herein in connection with the sale of this product 4510 W 6lst St North Phone 605 332 6513 ja Sioux Falls SD 57107 Fax 605 339 4106 www dakotadigital com dakotasupport dakotadigital com Copyright 2011 Dakota Digital Inc 16 MAN 650227 E
25. rket transmissions or if you ve changed wheel size or sprocket size To program the gear positions begin at a section of road where you can gradually shift through all of the gears Press and hold the switch while turning the key on and starting the engine Once the engine is running release the switch Press and release the switch until ECH is displayed Press and hold the switch until is displayed Press and release the switch until SEAr is displayed press and hold the switch until is displayed The display will show oF F F E5EE or LEArn oF F will disable the indicator F E5Ek will set the indicator for an original factory transmission LEArn allows it to work with virtually any transmission option To program each gear individually press and release the switch until LEArn is displayed then press and hold the switch The message will show LU ELH if the engine rom is below 1500 or LU 5Fa if the vehicle speed is below 5 MPH Begin driving in 1 gear The display should show JEAr and the should be flashing Drive at a steady speed until the goes steady and then changes to a flashing 2 it should only take about 20 seconds if the speed and RPMs are steady gt Optional If the gear does not stop flashing you can manually override and jump to the next gear by pressing and releasing the switch to store the gear position quicker Shift to
26. sired setting e Press and hold the switch until is displayed to select the setting e OFF turns the range display off e Turning the function an will access the following menus O done exits the setup o rESEk resets the gauge to beginning of the initial range learning o SEndEr used to change or reset the fuel gauge readings es dil set to 2004 2007 model with Dakota Digital fuel gauge e gJ set to 2008 2012 model with Dakota Digital fuel gauge HOY set to 2004 2007 factory fuel gauge HOH set to 2008 2012 factory fuel gauge d set to a custom fuel curve with Dakota Digital fuel gauge e SEk OO set new empty reading dan indicates it was stored Errar indicates the signal is out of range e SEE 99 set new full reading C5E set to a custom fuel curve with factory fuel gauge e SEk OO set new empty reading dan indicates it was stored Errar indicates the signal is out of range e SEE 99 set new full reading e Press and release the switch to select the desired fuel setup menu press and hold it until is displayed and then release the switch to view or go on e Apress and hold will save the setting or exit back to the menu e dont is the first menu displayed a press and hold will exit fuel set up at this point e rE5EL will begin the initial range learning again You must begin with a full tank of gas and then ride it down to less than 1 4 tank This can be
27. t is displayed Press and hold until is displayed to save the settings Turn the key off 14 MAN 650227 E FUEL SETUP The fuel gauge can be set to read two stock Harley sensor curves see setup procedure below for correct sender selection There is also a non adjustable warning feature that will flash the gauge at any reading below 10 as a low fuel warning indicator e To enter setup press and hold the switch while turning the key on e Release the switch The gauge will show i e Press and release the switch until FUL is displayed then press and hold the switch until Sad is displayed e Press and release the switch until the correct sender type is displayed 10 for 73 10 33 for 240 33 CUS for custom or CAL for custom sender programming The stock fuel sender 2004 2007 should use the 0 setting for correct readings or JJ for 2008 If CAL is not selected press and hold until is displayed Turn the key off e If CLUS is selected and a custom fuel curve has not yet been programmed the gauge will immediately enter the LAL routine e If LAL is selected the fuel sender curve can be programmed into the gauge Begin with an empty tank The gauge will be showing 00 and switch to displaying the measured resistance Press and release the switch to save the empty reading e The display will show 33 and then switch to displaying the m
28. tor wire has about 0 volts not work when the indicator should be off and about 12 volts when the indicator should be on Engine indicator does No data from ECM Check engine trouble codes not work ECM performance tune Stock service tools look for all stock gauges Unplug MCL 3006 and reprogram ECM MCL 3006 can be or reprogramming fails plugged back in as soon as reprogramming is complete 15 MAN 650227 E Tachometer Troubleshooting guide Problem Possible cause Solution Gauge will not light up Orange wire does not have power Connect to a location that has power Black wire is not getting a good ground Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Gauge lights up but tach No data from ECM Check engine trouble codes will only show zero Tach reading is erratic or Tach signal wire is loose or broken Check all wire connections and inspect wire for breaks jumps around Poor ground connection Check ground connection on tachometer engine and ignition system Update rate is too fast Reset display update speed slower Gear indicator is always Gears not programmed Program gear indicator in setup see instructions Gauge will not dim Night dimming is turned off or too low Change night setting in setup see instructions Gauge remains dim at all Night dimming is turn too high Change night setting in setup see instructions times Light sensor at bottom o
29. wire does not have power Connect to a location that has power Black wire is not getting a good ground Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Gauge lights up but speed No data from ECM Check engine trouble codes will only show zero Speed sensor not grounded properly Move ground to different location preferable close to the speedometer ground Sensor is not sending a speed signal Check for a damaged or malfunctioning speed sensor Speed reading is erratic or Speed sensor wire is loose or broken Check all wire connections and inspect wire for breaks jumps around Poor ground connection Check ground connection on speedometer and sensor Ignition Interference Check for tachometer wires routed with VSS signal wires Check for VSS signal wires routed near ignition coils Check for poor ignition system ground Use suppression spark plug wires Speed reading is incorrect Gauge is not calibrated correctly Gauge must be calibrated see instructions Gauge will not dim Blue wire 2 pin harness is not connected Check wiring connections Blue wire should have 12 volts correctly when tachometer is dim Gauge remains dim at all Blue wire 2 wire harness is getting power all Check wiring connections Blue wire should have 0 volts times all of the time when tachometer is bright Security indicator does Loose or incorrect connection to indicator wire Check that the appropriate indica
30. y from the factory only desired warning points may need adjustment The fuel sender needs to be set per application as well The only gauge that may require setting after the initial install is the Clock function on the tachometer so it is the first setup menu Speedometer Tachometer Pressure Gauge Unit MPH Clock Cal O range 8 7 Sender 60PSI user selectable Service meter OFF Night Dimming 1 darkest HI warn 51 PSI range varies with sender Performance Menu ON Display Update 3 fastest 1 8 sec Lo warn 7 PSI range 02 32 psi Fuel OFF RPM Warning 5500 range 2200 9900 Volt Gauge Oil Temp Gauge Fuel Gauge Lo warn 11 1 V range 9 6 12 6 Sender Set to deg F user selectable scale Sender 10 ohm sender user selectable Hi warn 15 4 V range 13 9 16 9 Hi warn 230 F range 200 290F or 93 143C LoWarn 1096 not adjustable 10 MAN 650227 E SPEEDOMETER SETUP Main Menu Sub Menu Description SPd d A9 read diagnostic codes from engine or security modules Addu SE select adjust calibrate speed un IE select speed unit MPH or km h IEL miles to service setting FErF enable disable performance readings FuEL setup fuel information rAndE setup miles to empty function odo one time odometer preset only shown while odometer has less than 100 miles Press and hold the switch while turning the key on Release the switch The speedometer will show Press PEL and release the switch so that SPd is displayed Press and hold t
Download Pdf Manuals
Related Search