Introduction Application Limits Wiring Detail Symbols
Contents
1. EN 070400 PSXM2190P Transition Plate Kit 3 Way amp 4 Way XM Valves to MicroKing IE Manifold Plate MUST be assembled with these two holes towards the Port 1 side of the manifold Special Valve to Base Mounting Screws 3 48 x 1 1 2 Long 6 to 10 In Lb 7 to 1 1 Nm PRODUCTS AND OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH PERSONAL INJURY AND PROPERTY DAMAGE Not Included XM 3 2 or 4 2 Valve in this Kit This document and other information from Parker Hannifin Corporation its subsidiaries and authorized distributors provide product and or system options for further investigation by users having technical expertise It is important O rings Transition Plate amp Manifold 4 that you analyze all aspects of your application including consequences of any failure and review the information concerning the product or systems in the current product catalog Due to the variety of operating conditions and applications for these products or systems the user through its own analysis and testing is solely responsible for making the final selection of the products and systems and assuring that all performance safety and warning requirements of the application are met Transition Plate Top Mounting Screws Bottom Transition Plate 6 to 10 In Lb to Base 7 to 1 1 Nm M3 x 12mm The products described herein including without limitation product features specifications design2. variety of operating conditions and applications for these products or systems the user through its own analysis and testing is solely responsible for making the final selection of the products and systems and assuring that all performance safety and warning requirements of the application are met The products described herein including without limitation product features specifications designs availability and pricing are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR INCLUSION IN EQUIPMENT MAINTENANCE MANUALS THAT UTILIZE THESE PRODUCTS CONTACT YOUR LOCAL REPRESENTATIVE XM Series Air Control Valves 1 8 Inline amp Subbase 3 2 amp 4 2 Inline Valve Accessories PSXM8288P Mounting Bracket V675P Inline Valve on Inlet Exhaust Manifold Assembly 1 Install the O rings Item 1 in the counterbores on top of the Manifold Item 2 2 Place the Valve on the Manifold For 3 Way N C Valve operation Item Electrical Connectors 9 4mm 4 line up the Solenoid end of the Valve with Port 1 on the Manifold Unwired Plug with For 3 Way N O operation Item 5 line up the Solenoid end of the Voltage Plug 6 Lead Valve with Port 3 on the manifold For 4 Way Valve operation Item 6 line up the Solenoid end of the Valve with Port 1 on the Manifold None N A PESC10 PESC12 Install the two Socket Head Cap Sc
3. Lb 7 to 1 1 Nm 8 MicroKing 4 Way Selector Plate 1 MicroKing 3 Way Not Included Subbase in this Kit
4. Mounting Kit Subbase amp IEM Valves can be mounted in any position in most environments in keeping with specifications XM valves feature a Class B insulation system and molded coil Valves should be mounted using the 16 4 0mm diameter side mounting holes and 6 M3 5 mounting screws The optional mounting bracket consists of a bracket two 8 32 screws and two captive lockwasher nuts Mounting bracket adapts to any 3 Way or 4 Way valve on either side of the valve Recommended Lubricant If in service lubricant is used Parker F442 oil is recommended Parker F442 is specially formulated to promote maximum service life of air Subbase Valve Accessories Kit No Description PSXMB8100P Item 10 8 Valve to AS Bolt Kit operated equipment Other compatible lubricants should be of straight Rego AE i paraffin base mineral oil having a viscosity of 100 200 SSU 100 F and PSXM8310P Not Shown seses Subbase Blanking Plate Kit an Aniline Point greater than 200 F PSXM4900P Item 4 sseseeseesssrerrsisrsisrisrnrisrreisrnee Isolation Plugs 3 r AN AUTION D t thetic tituted l th PSXM31010P Item 1 2 6 7 assin End Plate Kit NPT CAUTION Do fiot use Synthetic reconstituted or oils wi alcohol content or detergent additives PSXM530CP Item 2 3 5 aese Manifold Subbase Kit NPT Pneumatic Division Richland Michigan 49083 To avoid unpredictable system behavior that can cause personal injury and property da
5. Pneumatic Division Richland Michigan 49083 To avoid unpredictable system behavior that can cause personal injury and property damage Disconnect electrical supply when necessary before installation servicing or conversion Disconnect air supply and depressurize all air lines connected to this product before installation servicing or conversion Operate within the manufacturer s specified pressure temperature and other conditions listed in these instructions Medium must be moisture free if ambient temperature is below freezing Service according to procedures listed in these instructions Installation service and conversion of these products must be performed by knowledgeable personnel who understand how pneumatic products are to be applied After installation servicing or conversion air and electrical supplies when necessary should be connected and the product tested for proper function and leakage If audible leakage is present or the product does not operate properly do not put into use Warnings and specifications on the product should not be covered by paint etc If masking is not possible contact your local representative for replacement labels Safety Guide For more complete information on recommended application guidelines see the Safety Guide section of Pneumatic Division catalogs or you can download the Pneumatic Division Safety Guide at www parker com safety Introduction Follow these instr
6. mage Disconnect electrical supply when necessary before installation servicing or conversion Disconnect air supply and depressurize all air lines connected to this product before installation servicing or conversion Operate within the manufacturer s specified pressure temperature and other conditions listed in these instructions Medium must be moisture free if ambient temperature is below freezing Service according to procedures listed in these instructions Installation service and conversion of these products must be performed by knowledgeable personnel who understand how pneumatic products are to be applied After installation servicing or conversion air and electrical supplies when necessary should be connected and the product tested for proper function and leakage If audible leakage is present or the product does not operate properly do not put into use Warnings and specifications on the product should not be covered by paint etc If masking is not possible contact your local representative for replacement labels For more complete information on recommended application guidelines see the Safety Guide section of Pneumatic Division catalogs or you can download the Pneumatic Division Safety Guide at www parker com safety FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE Installation amp Service Instructions V676P XM to MicroKing Transition Kits ISSUED May 2007 Supersedes None DOC V676P
7. nimum rating of 1 6 times the rated voltage of the solenoid valve and sufficient capacity to dissipate the energy of other inductive loads Wiring Detail a el IO 1 1 112 14 NPT 2 Conduit Thread M Ground Conduit Option 15MM 3 Pin DIN Grommet Option Option Symbols 2 24 12 14 12 Operator Operator ve Operator End Ty End End 32 13 a2 13 2 4 14 NI A i 12 Operator lk Operator End End 1 3 4 2 With Flow Control 3 Way Options 3 Way Normally Closed 3 Way Normally Open 2 Way Normally Closed 2 Way Normally Open Selector Diverter 4 Way Options Normal Function 4 Way used as 3 Way NC 4 Way used as 3 Way NO Plug Exhaust Cylinder Cylinder Exhaust FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH PERSONAL INJURY AND PROPERTY DAMAGE This document and other information from Parker Hannifin Corporation its subsidiaries and authorized distributors provide product and or system options for further investigation by users having technical expertise It is important that you analyze all aspects of your application including consequences of any failure and review the information concerning the product or systems in the current product catalog Due to the
8. rews Item 3 provided and tighten LED amp 12 24VDC PESC2020B PESC2220B to 6 to 10 in lb 7 to 1 1 Nm torque using a 5 64 inch hex wrench Suppression 120VAC PESC2001F PESC2201F 3 When DIN Rail Mounting Bracket is provided install Screws through the Manifold and secure the DIN Rail Connecting Bracket on both s ends of the Manifold Subbase Valve and Manifold Assembly 4 Test valve for functional operation and for internal and external 1 Place o ring seals Item 2 into End Cap possessing o ring grooves Item 1 and thread spacers Item 5 into this End Cap Assemble subbase Item 3 with O rings Item 2 onto spacers using subbase through holes Repeat for remaining manifold stations Place the End Cap Item 6 without o ring grooves on last subbase with O rings Secure entire assembly with 6 32 x 50 inch screws Item 7 supplied with End Cap and tighten with 7 64 inch hex drive wrench not supplied To assemble valves place o rings Item 8 four per subbase supplied with valve Item 9 onto the valve mounting surface on the subbase Light weight grease assists in maintaining o ring position during assembly Mount Valves to subbase assembly with 3 48 x 1 25 socket head cap screws Item 10 supplied with valve Use 6 to 10 in lb 7 to 1 1 Nm of torque 4 Way and 3 Way valves are mounted with Solenoids Coils facing away from subbase delivery ports 2 and 4 For 3 Way N O Functions valves mu
9. s availability and pricing are subject to change by Parker O rings Transition Plate Hannifin Corporation and its subsidiaries at any time without notice Transition Plate Bottom EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR INCLUSION IN EQUIPMENT MAINTENANCE MANUALS THAT UTILIZE THESE PRODUCTS CONTACT YOUR LOCAL REPRESENTATIVE Not Included MicroKing IEM in this Kit XM to MicroKing Transition Kit PSXM2191P Transition Plate Kit 3 Way Subbase XM Valves to MicroKing 3 Way Subbase Standard Valve to Base Mounting Screws 3 48 x 1 1 4 Long 6 to 10 In Lb 7 to 1 1 Nm Not Included in this Kit Special Male Female 6 to 10 In Lb Stud 7 to 1 1 Nm XM 3 2 Subbase Valve PSXM2192P Transition Plate Kit 4 Way XM Subbase Valves to MicroKing 4 Way Subbase Standard Valve to Base Mounting Screws 3 48 x 1 1 4 Long V676P 6 to 10 In Lb 7 to 1 1 Nm XM 4 2 Subbase Valve Special Male Female Stud Not Included in this Kit 6 to 10 In Lb 7 to 1 1 Nm O rings Transition Plate to Valve Small O rings Transition Plate Transition Plate MicroKing Selector Plate NC Use if replacing NC Valve MicroKing Selector Plate NO Use if replacing NO Valve MicroKing 3 Way Not Included Subbase in this Kit O rings Transition Plate to Valve Large Transition Plate Standard Mounting Screws M3 x 10mm 6 to 10 In
10. st be isolated from the other 3 Way N C and 4 Way valves on the manifold This is achieved by placing port isolator discs Item 4 in between the subbase of the first 3 Way N O Valve and the subbase of the last 3 Way N C or 4 Way valve in the Subbase Manifold Inlet pressure is connected to Port 3 of the manifold for the 3 Way N O valves Inlet pressure is connected to the Port 1 of the manifold for the 3 Way N C and 4 Way valves Test valve for functional operation and for internal and external leakage If leakage is audible most likely indicating improper assembly do not operate conduct assembly again leakage If leakage is audible most likely indicating improper assembly do not operate conduct assembly again Instructions for Converting NC to NO 3 Way Valves on Existing IEM Manifolds Remove the 3 Way Valve from the Base Replace the Valve 180 from the original position for N C function Line up the Solenoid end of the Valve with Port 3 on the manifold Reinstall the two Screws Item 3 and tighten 6 to 10 in lb 7 to 1 1 Nm torque Turn on air pressure and electrical power source Test valve for proper functional operation and for internal and external leakage IEM Manifold Accessories oO Kit No Description PSXM2194P Not Shown sessen IEM Blanking Plate Kit PSXM2186P Item 1 3 Valve to IEM Mounting Kit 10 O rings amp 10 Bolts Kit PS2190P Not Shown DIN Rail
11. uctions when installing operating or servicing the product VALVE IS NOT DESIGNED FOR FIELD SERVICE Application Limits These products are intended for use in general purpose compressed air systems only Operating Pressure kPa PSIG bar Maximum 850 125 8 5 Minimum 30 14 7 1 Ambient Temperature Range 0 C to 50 C 32 F to 125 F Voltage Range 85 110 of rated voltage These limits should not be exceeded EXCEPTION The 45 and 49 voltage code rated Valves may be operated at 70 125 of the rated voltage VAN CAUTION An interruption of 10 milliseconds or greater to the power supplied to the solenoid of a solenoid operated valve may cause the valve to shift Provision must be made to prevent power interruption of this duration to avoid unintended potentially hazardous consequences VAN CAUTION This valve contains solid state components that can be damaged by transient voltage spikes over voltage or high temperature To protect against premature solenoid failure please read and adhere to the following Installation amp Service Instructions V675P XM Series Air Control Valves 1 8 Inline amp Subbase 3 2 amp 4 2 ISSUED March 2007 Supersedes None DOC V675P EN 061246 If this solenoid operated valve is used in a circuit with other inductive loads the solenoid should be electrically protected with a voltage suppression device e g transient voltage suppressor or varistor that has a mi
Download Pdf Manuals
Related Search