Mercedes Benz G-class (W463)
Contents
1. 4 Prepare to connect the LED lamps Insulate any spare harness R XXInsulate OEM fog h 4 5 Paint WALD Head Light Cover according to the picture PRSP R OE ERE SS ATTACHED LED LAMP AFTER PAINTING 6 Completely degrease the installation positions for WALD Exhaust Trim 7 Use caulking glue to fix WALD Exhaust Trim on WALD Rear Bumper 8 Leave them till completely fixed 9 Install WALD Rear Bumper to the body XWALD SHOWCAR IS PAINTED LIKE THE PICTURE STEP 5 Make clear coating for the carbon parts of WALD Front Bumper MATTE BLACK LED LAMP GUIDE WALL X Use heat resistant caulking glue to fix the attached LED lamps Q Face of lens Fix the attached LED lamps according to the picture Were OOQ OEM TAPPING scREws ATTACHED LED LAMP N ATTENTION X MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK DURING ALL THE INSTALLATION PROCESS PLEASE BE CAREFUL NOT TO DAMAGE THE BODY 2 ADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY WALD INTERNATIONAL WALD INTERNATIONAL ADD 10 13 KYOGUCHI CHO TAKATSUKI OSAKA JAPAN ZIP 569 0072 TEL 81 72 673 3000 FAX 81 72 673 3003 2013 04 INSTALLATION MANUAL WALA SPORTS LINE Mercedes Benz G class o Lammas WA THANK YOU FOR PURCHASING THIS IS THE INSTALLATION MANUAL OF WALD BONNET FOR MERCEDES BENZ W463 G CLASS X NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING f HEO PARTS QU2. The product is made of FRP Handle with care Do not give the excessive force Gradually fix the bolts and nuts by checking the fitment and balance of the installation Check the fitment and adjust all the details of the fitment steady and proper Please check the fitment and all the details regularly fix the bolts and nuts as necessary The instruction of painting is just our recommendation please paint it as you like X PLEASE BE AWARE OF E You may lose the warranty and all the services from the car maker because of replacing OEM parts E Reduced road clearance may cause inconvenience in using parking curbs and garage jack E FRP ABS and PPE products are slightly weaker than OEM parts in crashes E The product may not match the body and OEM color perfectly Use caulking glue Do not wash the car during this time BEFORE PAINTING 1 Remove OEM front bumper according to the Mercedes Benz service manual EHOW TO FIX OEM INTERCOOLER TO THE BODY Step 1 gt XUse the bracket sold separately to fix OEM intercooler to the body only for Turbo Model 2 Relocate all the necessary OEM parts and WALD Front Grille to WALD Front Bumper INTERCOOLER X Adjust the details of WALD Front Bumper to fit the body by rasps or sandpapers 3 Paint WALD Front Bumper and Front Grille according to the picture B OEM PLASTIC NUT BRACKET Ss AFTER PAINTING i 4 Install the attached meshes to WALD Front Bumpe
3. WALD Rear Door Panels Be careful to adjust the location and balance based on a car 2013 04 WALD INTERNATIONAL Mercedes Benz G class THANK YOU FOR PURCHASING THIS IS THE INSTALLATION MANUAL OF WALD FRONT BUMPER FOR MERCEDES BENZ W463 G CLASS PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION E Please purchase double sided tape i primer and caulking glue at auto accessory shop or hardware store X NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING X CHECK THE FITMENT AND ADJUST ALL THE DETAILS BEFORE PAINTING E We assume no responsibility for any damage resulting from improper installation painting modification and any cut wound in unsealing ATTENTION Contact the car dealer when you have any question in removing OEM parts During all the installation process use parking brake and stop the engine completely E Use rasps or sandpapers to fit the products to the body if there is an individual difference E The product is made of FRP Handle with care Do not give the excessive force Gradually fix the bolts and nuts by checking the fitment and balance of the installation Check the fitment and adjust all the details of the fitment steady and proper Please check the fitment and all the details regularly fix the bolts and nuts as necessary The instruction of painting is just our recommendation please paint it as you like X PLEASE BE AWARE OF E You may lose
4. 72 673 3000 FAX 81 72 673 3003 2013 04 Hx fF at BA SS Sportliche Autoausriistung WALD International WALA SPORTS LINE BLACK BISON EDITION Mercedes Benz G class m THANK YOU FOR PURCHASING THIS IS THE INSTALLATION MANUAL OF WALD HEAD LIGHT COVER FOR MERCEDES BENZ W463 G CLASS X NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING it i ARTS QUANTITIES X CHECK THE FITMENT AND ADJUST ALL THE DETAILS BEFORE PAINTING Please purchase double sided tape REAR BUMPER HEAD LIGHT COVER TSET E We assume no responsibility for any damage resulting from improper installation painting primer and caulking glue at p modification and any cut wound in unsealing T auto accessory shop or hardware store ATTENTION E Contact the car dealer when you have any question in removing OEM parts A E During all the installation process use parking brake and stop the engine completely E Use rasps or sandpapers to fit the products to the body if there is an individual difference LED LAMP 1 SET i f Completely degrease and paint primer on all the installation positions to enhance the viscidity E i of double sided tape i i Use dryer to warm double sided tape to enhance I the viscidity in low temperature The product is made of FRP Handle with care Do not give the excessive force Gradually fix the bolts and nuts by checking the fitment and balance of the installation Check the fitment and
5. adjust all the details of the fitment steady and proper Please check the fitment and all the details regularly fix the bolts and nuts as necessary The instruction of painting is just our recommendation please paint it as you like it 1 iti PLEASE BE AWARE OF i Keep the car in a dry condition more than E You may lose the warranty and all the services from the car maker because of replacing OEM parts 24 hours after gluing o E Reduced road clearance may cause inconvenience in using parking curbs and garage jack Do not wash the car during this time E FRP ABS and PPE products are slightly weaker than OEM parts in crashes E The product may not match the body and OEM color perfectly Use caulking glue x to fill the aan HE between the product Li and the body BEFORE PAINTING 1 Remove OEM head light cover according WIRING DIAGRAM E HOW TO INSTALL THE ATTACHED LED LAMPS STEP 2 7 Inside of WALD Head Light Cover to the Mercedes Benz service manual 2 Temporarily install the attached LED lamps according to the guide wall on WALD Head Light Cover gt XAdjust the details of WALD Head Light Cover to fit the attached LED lamps by rasps or sandpapers 3 Temporarily install WALD Head Light Cover to the body Adjust the details of WALD Head Light Cover to fit the body by rasps or sandpapers AS DAYLIGHT LED LAMP RED IGNITION BLACK Le GROUNDING WIRE POSITION LAMP
6. the warranty and all the services from the car maker because of replacing OEM parts i i i Do not wash the car during this time E Reduced road clearance may cause inconvenience in using parking curbs and garage jack E FRP ABS and PPE products are slightly weaker than OEM parts in crashes E The product may not match the body and OEM color perfectly BEFORE PAINTING 1 Temporarily install WALD Roof Spoiler and Rear Gate Spoiler to the body Check all the details of the fitment then use masking tape to mark the installation position 2 Mark the installation positions on the body according to the picture then remove WALD Rear Gate Spoiler and Roof Spoiler 3 Make holes on the rear gate from the rear to insert the attached tapping screws Use touch up paint to make corrosion treatment on holes 4 Remove WALD Roof Spoiler and Rear Gate Spoiler then make holes on them AFTER PAINTING 5 Use caulking glue to install WALD Rear Gate Spoiler and Roof Spoiler to the body after completely degreasing the installation positions 6 Fix the attached tapping screws from the rear gate MHOW TO MAKE HOLES STEP 3 to install WALD Roof Spoiler Taking off the cover inside of the rear gate then make holes Insulate the holes for the purpose of waterproof and anti rust 7 Check all the details of the fitment then fix the attached tapping screws ATTACHED LED LAMP Inside of WALD Roof Spoiler gen A ATTENTION XM
7. ANTITIES X CHECK THE FITMENT AND ADJUST ALL THE DETAILS BEFORE PAINTING Please purchase double sided tape E We assume no responsibility for any damage resulting from improper installation painting primer and caulking glue at modification and any cut wound in unsealing auto accessory shop or hardware store ATTENTION E Contact the car dealer when you have any question in removing OEM parts E During all the installation process use parking brake and stop the engine completely Completely degrease and paint primer on all i E Use rasps or sandpapers to fit the products to the body if there is an individual difference the installation positions to enhance the viscidity E The product is made of FRP Handle with care Do not give the excessive force p Gradually fix the bolts and nuts by checking the fitment and balance of the installation of double sided tape a aaaaaaaaa E Check the fitment and adjust all the details of the fitment steady and proper Use dryer to warm double sided tape to enhance U Iking el Please check the fitment and all the details regularly fix the bolts and nuts as necessary the viscidity in low temperature m ie Fite ae E The instruction of painting is just our recommendation please paint it as you like X PLEASE BE AWARE OF Keep the car in a dry condition more than between the product E You may lose the warranty and all the services from the car maker because of replacing
8. INSTALLATION MANUAL WALO SPORTS LINE Mercedes Benz G class uo Beem WALDA THANK YOU FOR PURCHASING THIS IS THE INSTALLATION MANUAL OF WALD FRONT BUMPER FOR MERCEDES BENZ W463 G CLASS PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION X NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING X CHECK THE FITMENT AND ADJUST ALL THE DETAILS BEFORE PAINTING E We assume no responsibility for any damage resulting from improper installation painting modification and any cut wound in unsealing ATTENTION Contact the car dealer when you have any question in removing OEM parts g During all the installation process use parking brake and stop the engine completely E E Use rasps or sandpapers to fit the products to the body if there is an individual difference AN f i PARTS QUANTITIES Please purchase double sided tape FRONT BUMPER FRONT BUMPER primer and caulking glue at FRONT GRILLE i MESHES FOR FRONT BUMPER auto accessory shop or hardware store ESE Eo RON ORTLE ee LED LAMP KIT Completely degrease and paint primer on all RUBBER MOLDING the installation positions to enhance the viscidity BOLTS M6 x 12 of double sided tape RUBBER WASHERS Use dryer to warm double sided tape to enhance the viscidity in low temperature to fill the gap Keep the car in a dry condition more than between the product 24 hours after gluing it and the body
9. LER LAMP WALD INTERNATIONAL WALD INTERNATIONAL ADD 10 13 KYOGUCHI CHO TAKATSUKI OSAKA JAPAN ZIP 569 0072 TEL 81 72 673 3000 FAX 81 72 673 3003 2013 04 INSTALLATION MANUAL WALO SPORTS LINE Mercedes Benz G class uo Beem WALDA THANK YOU FOR PURCHASING THIS IS THE INSTALLATION MANUAL OF WALD REAR BUMPER FOR MERCEDES BENZ W463 G CLASS PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION X NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING X CHECK THE FITMENT AND ADJUST ALL THE DETAILS BEFORE PAINTING E We assume no responsibility for any damage resulting from improper installation painting modification and any cut wound in unsealing i ATTENTION Contact the car dealer when you have any question in removing OEM parts g During all the installation process use parking brake and stop the engine completely E E Use rasps or sandpapers to fit the products to the body if there is an individual difference AN E E E PARTS QUANTITIES Please purchase double sided tape REAR BUMPER REAR BUMPER primer and caulking glue at MESHES i RUBBER MOLDING auto accessory shop or hardware store SORES MENTO Completely degrease and paint primer on all Aa HERS the installation positions to enhance the viscidity of double sided tape Use dryer to warm double sided tape to enhance the viscidity in low temperature Keep the car in a dry condition more than 24 hours after gluin
10. OEM parts 24 hours after gluing o andthe body E Reduced road clearance may cause inconvenience in using parking curbs and garage jack Do not wash the car during this time E FRP ABS and PPE products are slightly weaker than OEM parts in crashes E The product may not match the body and OEM color perfectly BEFORE PAINTING 1 Temporarily fix the attached LED lamps according Y WIRING DIAGRAM to the guide line wallls on WALD Front Bumper EHOW TO INSTALL THE ATTACHED doe td ae Adjust the details of WALD Front Bumper to fit the LED LAMPS STEP 1 3 AS FOG LAMP attached LED lamps by rasps or sandpapers LED LAMP m ATTACHED BOLTS M5 x 15 re0 e FOG LAMP 2 Prepare to connect the attached LED lamps o RED Insulate any spare harness g Ecc NOT CONNECTING 3 Paint WALD Bonnet according to the picture AFTER PAINTING 4 Completely degrease the installation positions then put the atached LED lamps according to the guide line walls on WALD Front Bumper LED GUIDE LINE 5 Use caulking glue to fix the attached LED lamps ATTACHMENT WALL after checking the angle and location 6 Leave them till completely fixed 5 me ies Ce ore rev e 7 Install WALD Front Bumper to the body after connecting the harness LED LAMP Face of the lens ATTACHED BOLTS M5 x 15 Insulate OEM fog lamp harness EONS Eya X WALD SHOWCAR IS PAINTED LIKE THE PICTURE
11. ORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK DURING ALL THE INSTALLATION PROCESS PLEASE BE CAREFUL NOT TO DAMAGE THE BODY XADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY WALD INTERNATIONAL ADD 10 13 KYOGUCHI CHO TAKATSUKI OSAKA JAPAN ZIP 569 0072 TEL 81 72 673 3000 FAX 81 72 673 3003 INSTALLATION MANUAL WA L C Sportliche Autoausr stung WALD International WALDO SPORTS LINE BLACK BISON EDITION PARTS QUANTITIES ROOF SPOILER ROOF SPOILER 1 TAPPING SCREWS M5 x 10 4 REAR GATE SPOILER REAR GATE SPOILER i i Completely degrease and paint primer on all i the installation positions to enhance the viscidity of double sided tape Use dryer to warm double sided tape to enhance the viscidity in low temperature i Keep the car in a dry condition more than 24 hours after gluing i m Use caulking glue to fill the gap between the product and the body Scuff and degrease the surface of WALD Roof Spoiler and the body before installing 2013 04
12. STEP 4 N The LED attachment of WALD Show Car QO Fix the attached LED lamps is painted in Matte Black gt Even for Carbon Products according to the picture WALD Show Car is painted J 4 in Matte Black for these parts Make clear coating for the carbon parts of WALD Front Bumper 5 E Please purchase relay harness with remote controller kit to turn on the daylights or fog lamps separately A ATTENTION XREMOVE THE BATTERY BEFORE ALL THE WIRING WORKS LED LAMP KIT XMAKE SURE OEM FOG LAMPS ARE FINE TO WORK BEFORE THE INSTALLATION WALD INTERNATIONAL WALD INTERNATIONAL ADD 10 13 KYOGUCHI CHO TAKATSUKI OSAKA JAPAN ZIP 569 0072 TEL 81 72 673 3000 FAX 81 72 673 3003 2013 04 INSTALLATION MANUAL WALDO SPORTS LINE Mercedes Benz G class o Lammas WA 1 THANK YOU FOR PURCHASING THIS IS THE INSTALLATION MANUAL OF WALD BONNET FOR MERCEDES BENZ W463 G CLASS X NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING it PARTS QUANTITIES X CHECK THE FITMENT AND ADJUST ALL THE DETAILS BEFORE PAINTING Please purchase double sided tape BONNET E We assume no responsibility for any damage resulting from improper installation painting primer and caulking glue at BOLTS M6 x 12 modification and any cut wound in unsealing auto accessory shop or hardware store NUTS M3 ATTENTION E Contact the car dealer when you have any question in removing OEM parts tt E During
13. all the installation process use parking brake and stop the engine completely Completely degrease and paint primer on all The product is made of FRP Handle with care Do not give the excessive force Lio p Gradually fix the bolts and nuts by checking the fitment and balance of the installation of double sided tape My Vet cima reac eae ceaeecnee ic cet cee tase ENEE AT Check the fitment and adjust all the details of the fitment steady and proper Use dryer to warm double sided tape to enhance U Iking el Please check the fitment and all the details regularly fix the bolts and nuts as necessary ithe viscidity in low temperature l to fill the n a The instruction of painting is just our recommendation please paint it as you like Keep the car in a dry condition more than between the product PLEASE BE AWARE OF E E A hours after alui and the body E You may lose the warranty and all the services from the car maker because of replacing OEM parts ours after gluing o E Reduced road clearance may cause inconvenience in using parking curbs and garage jack Do not wash the car during this time E FRP ABS and PPE products are slightly weaker than OEM parts in crashes E The product may not match the body and OEM color perfectly A E Use rasps or sandpapers to fit the products to the body if there is an individual difference the installation positions to enhance the viscidity BEFORE PAINTING Re
14. des Benz G class m THANK YOU FOR PURCHASING THIS IS THE INSTALLATION MANUAL OF WALD OVER FENDER AND REAR DOOR PANEL FOR MERCEDES BENZ W463 G CLASS PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION X NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING X CHECK THE FITMENT AND ADJUST ALL THE DETAILS BEFORE PAINTING E We assume no responsibility for any damage resulting from improper installation painting modification and any cut wound in unsealing PARTS OVER FENDER INNER PANELS MESHES HE QUANTITIES Please purchase double sided tape primer and caulking glue at auto accessory shop or hardware store OVER FENDER i ATTENTION E Contact the car dealer when you have any question in removing OEM parts ae REAR DOOR PANEL REAR peor Anes i E During all the installation process use parking brake and stop the engine completely Completely degrease and paint primer on all E Use rasps or sandpapers to fit the products to the body if there is an individual difference the installation positions to enhance the viscidity E The product is made of FRP Handle with care Do not give the excessive force Gradually fix the bolts and nuts by checking the fitment and balance of the installation it of double sided tape y eo oOe Cky lgl aaan E Check the fitment and adjust all the details of the fitment steady and proper i Use dryer to warm doub
15. ers to the body and tighten OEM bolts and tapping screws EWALD SHOWCAR IS PAINTED LIKE THE PICTURE STEP 5 Make clear coating for the carbon parts of WALD Front Bumper EHOW TO INSTALL THE ATTACHED MESHES STEP 6 Use pins and caulking glue to install the attached meshes to WALD Rear Bumper from the rear XPaint the inside of the ducts and pins in black MATTE BLACK WALD REAR OVER FENDER er ATTACHED MESH OEM NUTS A ATTENTION EHOW TO INSTALL THE ATTACHED INNER PANELS STEP 2 Use OEM tapping screws to connect the attached inner panels with OEM OVER MOLDI OEM inner liners gt XAdjust the shape and location based on OEM inner liners ATTACHED INNER PANE Use OEM tapping screws for WALD Front and Rear Over Fenders OEM OVER FENDER MOLDING OEM BOLTS X MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK DURING ALL THE INSTALLATION PROCESS PLEASE BE CAREFUL NOT TO DAMAGE THE BODY X ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY Recommend to paint protective coating on the back side of WALD Over Fender WALD INTERNATIONAL WALD INTERNATIONAL ADD 10 13 KYOGUCHI CHO TAKATSUKI OSAKA JAPAN ZIP 569 0072 TEL 81 72 673 3000 FAX 81 72 673 3003 between the product and the body FENDER NG WALD DOOR PANEL amp FENDER PANEL EHOW TO PROCESS WALD REAR OVER FENDER STEP 2 y Need to cut WALD Rear Over Fender and OEM Door Molding when installing
16. g Do not wash the car during this time The product is made of FRP Handle with care Do not give the excessive force Gradually fix the bolts and nuts by checking the fitment and balance of the installation Check the fitment and adjust all the details of the fitment steady and proper Please check the fitment and all the details regularly fix the bolts and nuts as necessary The instruction of painting is just our recommendation please paint it as you like X PLEASE BE AWARE OF E You may lose the warranty and all the services from the car maker because of replacing OEM parts E Reduced road clearance may cause inconvenience in using parking curbs and garage jack E FRP ABS and PPE products are slightly weaker than OEM parts in crashes E The product may not match the body and OEM color perfectly BEFORE PAINTING 1 Remove OEM rear bumper according to the Mercedes Benz service manual Use caulking glue to fill the gap between the product and the body EHOW TO INSTALL OEM BRACKET STEP 2 HOW TO INSTALL 2 Replace OEM brackets to WALD Rear Bumper nee 2 Replace OEM brackets from OEM Rear Bumper OEM MUD GUARD STEP 4 3 Temporarily fix WALD Rear Bumper to the body with all the necessary parts and fix them on WALD Rear Bumper with OEM bolts X Adjust the details of WALD Rear Bumper to fit the body by rasps or sandpapers and attached Nuts M8 Sat re mesa according to sll a a M6
17. le sided tape to enhance U Iking gl Please check the fitment and all the details regularly fix the bolts and nuts as necessary ithe viscidity in low temperature a to fill the ate B X PLEASE BE AWARE OF E You may lose the warranty and all the services from the car maker because of replacing OEM parts E Reduced road clearance may cause inconvenience in using parking curbs and garage jack E FRP ABS and PPE products are slightly weaker than OEM parts in crashes E The product may not match the body and OEM color perfectly The instruction of painting is just our recommendation please paint it as you like i Keep the car in a dry condition more than 24 hours after gluing it Do not wash the car during this time ni OVER FENDER amp REAR DOOR PANEL BEFORE PAINTING 1 2 Remove OEM over fender according to the Mercedes Benz service manual Temporarily install WALD Over Fender to the body See how to process on WALD Rear Over Fender when installing WALD Door Panel according to the picture 3 Mark the installation positions for OEM tapping screws on the attached inner panels to fix on WALD Rear Over Fenders 4 Make holes on the attached inner panels according to the marked positions 5 Paint WALD Over Fenders according to the picture AFTER PAINTING 6 7 8 Use caulking glue to fix the attached meshes from the rear Fix the attached inner panels on WALD Rear Over Fenders Install WALD Over Fend
18. move OEM bonnet according to the Mercedes Benz HOW TO REPLACE OEM WASHER PANEL service manual STEP 2 HINGES Replace from OEM bonnet BONNET RELEASE LEVER Replace from OEM bonnet Replace OEM washer panel to WALD Bonnet RUBBER CUSHIONS 2 Temporarily install WALD Bonnet to the body after pre fixing all the necessary parts Use OEM Clips to fix on WALD Bonnet Adjust the details of WALD Bonnet to fit the body by rasps or sandpapers OEM BONNET GRILLE 3 Paint WALD Bonnet according to the picture AFTER PAINTING 4 Fix all the necessary parts to WALD Bonnet z ATTACHED BOLTS then install to the body M6 x 12 5 Tighten OEM bolts attached bolts and nuts after Ay ATTACHED NUT checking the balance XWALD SHOWCAR IS PAINTED LIKE THE PICTURE STEP 3 Make clear coating for the carbon f i j parts of WALD Front Bumper E 7 gt OEM BOLTS OEM BOLTS a OEM BONNET INSULATION Use heat resistant glue to fix on OEM bonnet A ATTENTION XMORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK DURING ALL THE INSTALLATION PROCESS PLEASE BE CAREFUL NOT TO DAMAGE THE BODY XADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY WALD INTERNATIONAL WALD INTERNATIONAL ADD 10 13 KYOGUCHI CHO TAKATSUKI OSAKA JAPAN ZIP 569 0072 TEL 81 72 673 3000 FAX 81 72 673 3003 2013 04 INSTALLATION MANUAL Sportliche Autoausriistung WALD International WALA SPORTS LINE BLACK BISON EDITION Merce
19. r and Front Grille with caulking glue S ES 5 Fix the attached LED lamps and WALD Front Grille to WALD Front Bumper AG Ea 7 X Adjust optical axis and make sure the LED lamps are fine to work before the installation x5 6 Temporarily fix the attached rubber moldings to WALD Front Bumper 7 Check all the balance of the location and fitting then tighten all the OEM and attached bolts 0 BOLTS QEM NUT BRACKET SOLD SEPARATELY 8 Cut the pins on the back of OEM front grille emblem and use the caulking glue to fix it on WALD Front Grille X Leave it till completely fixed EWALD SHOWCAR IS PAINTED LIKE THE PICTURE STEP 3 OEM BOLTS ATTACHED XFix OEM bolts with the OEM fixture RUBBER MOLDING ATTACHED BOLTS M6 x 12 amp RUBBER WASHERS HOW TO INSTALL THE ATTACHED MESHES ne 4 XFix WALD Over Fender and Front Bumper together Use pins and caulking glue to install the attached meshes to WALD Front Bumper from the rear XPaint the inside of the ducts and pins in black e OEM BOLTS MATTE BLACK XFix OEM bolts through the attached brackets WALD Front B A ATTENTION WALD FRONT GRILLE pe x MORE EAL 2 EN ICIANS alt ee palate ae OTTO o a on the back reece tone a an Bumper Recommend to paint protective coating DURING ALL THE INSTALLATION PR PLEASE BE CAREFUL NOT TO DAMAGE THE BODY p i on the back side of WALD Over Fender X ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY ATTACHED
20. x 12 amp 4 Cut OEM mud guard according to the shape of WALD Rear Bumper OEM BRACKET E XFix WALD Over Fender and 5 Paint WALD Rear Bumper according to the picture OEM MUD GUARD Rear Bumper together AFTER PAINTING 6 Use caulking glue to fix the attached meshes from the rear 7 Fix OEM mud guard to WALD Rear Bumper Cut here About 8 cm X Use caulking glue if the OEM tapping screws are not available 8 Temporarily install WALD Rear Bumper to the body 9 Check all the details of the fitment then tighten all the OEM bolts and the attached bolts Recommend to paint protective coating EWALD SHOWCAR IS PAINTED on the back side of WALD Over Fender LIKE THE PICTURE STEP 5 Make clear coating for the carbon parts of WALD Front Bumper EHOW TO INSTALL THE ATTACHED MESHES STEP 6 Use pins and caulking glue to install the attached meshes to WALD Rear Bumper from the rear XPaint the inside of the ducts and pins in black ag OEM BOLT XFix OEM bolts through the MATTE BLACK ATTACHED MESH J i replaced brackets on A ATTENTION SN WALD Rear Bumper X MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK x A E IROD O ON an Ae SGEIRE BODY Replace from OEM Rear Bumper Replace from OEM Rear Bumper Replace from OEM Rear Bumper OEM REAR FOG LAMP LICENSE PLATE LIGHT OEM BACK UP LIGHT WALD INTERNATIONAL WALD INTERNATIONAL ADD 10 13 KYOGUCHI CHO TAKATSUKI OSAKA JAPAN ZIP 569 0072 TEL 81
Download Pdf Manuals
Related Search