SERVICE MANUAL DISHWASHER EDW 1503 +
Contents
1. 3 5 Detergent dispenser display lack ofrinse aid Dosing of detergent prewash 10 ml wash 20 30 ml maximum filling level Dosing of rinse aid position 1 6 2mi 7 mi Capacity 140 ml dosing of rinse aid outlet of rinse aid detergenttray detergent tray for pre wash coll Spule The detergent compartment 1 is filling corresponding to the set dosing aus Ll SAY quantity when the door is open Possibly existing rinse aid in compartments 2 and 3 flows back into the storage tank of the rinse aid The detergent trays are filled up The door will be closed and the detergent for prewash will be rinsed out through the slots in the detergent dispenser cover aus 1 1111 During the washing cycle the coil is switched on and the detergent compartment cover releases the detergent The rinse aid flows from compartment 1 into compartment 2 EIN AUS After switching off the coil the rinse aid flows from compartment 2 into compartment 3 During the rinse cycle the coil will be switched on when the rinse is warmed Zeit and the rinse aid runs from compartment 3 into the rinse tank At the same time the remaining rinse aid 15 runs from compartment 1 into compartment 2 En With the coil switched off the rinse aid flows from compartment 2 into compartment 3 EIN AUS During the rinse cycle the coil is always switched on twice When it is switched on the second time the remaining rinse aid fl2. Ifthe signal sound is deactivated it means that in general no acoustic end signal will sound any more 4 Even the acoustic fault signals cannot be heard any more 3 Press keys S2 and S3 simultaneously until the confirmation LEDs LD1 LD2 and LD3 are flashing 4 By actuating the function key S3 you now can call the function The confirmation LED LD3 continues flashing LEDs LD1 and LD2 go out The current condition whether the signal sound is active or not is indicated in the display 1b signal sound on Ob signal sound off EDW 1503 VGA LEA era ae ma Fa a a Fa Da HE aaa a an AAA LD1 LD2 LD3 Deactivation resp activation of the signal sound 1 99 SS SS E 5 6 By any further acuation of the function key S3 you can IO E SB SO activate resp deactivate the signal sound alternating Leaving the function After the last key pressure of the function key S1 you can leave the special program as follows After 60 seconds all LEDs of the program and option keys are lit automatically The indication in the display goes out The appliance is in the prestart mode again or the appliance is switched off by ON OFF key SO y Zn A AUS durch manuelle Bet tigung ber Ein Aus Saving the set condition The currently valid condition is saved directly after any entry 33 6 14 Service function readou
3. 20 secs This function is checked again on each step Programme is completed until next subprogramme without O Time limit during filling exceeded level No further filling up of water top up Error is reset after one complete drain cycle If 7 Segment display available no PAA error display Sound error display generally with VGA with other machines depending on model DGN TDS N List of Possible Error Causes Code Water tap is closed or faulty No water pressure pressure too low or changing Screen in front of inlet valve clogged Flow governor at inlet valve faulty Inlet valve faulty Inlet valve deenergized faulty wiring or no activation by electronics Inlet hose bent Softener system clogged by filling detergent into salt compartment for instance Upright installation without upright assembly kit Connection height of the discharge hose is lower than 30cm above appliance base Connection w o siphon or air chamber Pressure controller faulty Water level inside appliance is Pressure controller hose obstructed bent or leaking not detected Pressure controller wiring is faulty Screens in the appliance clogged also check spray arm nozzles for clogging Fault with discharge pump Discharge pump deenergized faulty wiring or no activation by electronics No or not enough water let in Machine runs dry Siphon effect Obstruction blocking filters in the appliance discharge opening in discharge trough discharge pump discha
4. YILT ie EI panal E H oo 8 D y a wa HO g MN LW a on Oo nu na o e gt GY0 Y3MOd 5 A 2 H OO S HLYW3 CN a eee dWY1 107ld HILIMS NIYW 1301 wood OYYOG NIYW 68 06 AO 599 515 184 EN 09 2002 R K
5. indication in the display 1L LED display rinse aid LED is lit in case of a lack of rinse aid gt LED goes out after rinse aid has been refilled Information The rinse aid addition can be deactivated completely by the customer This also deactivates the LED display rinse aid see description page B 12 Deactivation of rinse aid addition If the option 3 in 1 is selected special tablet option neither the salt LED nor the rinse aid LED is selected LED display water LED is lit when there is no or too less water filling into the appliance A reason for that could be for example a closed water tap The program is stopped and can be continued when the fault has been eliminated by actuating the program key see also description page B 19 Survey of fault displays fault 10 29 6 10 Short survey of all customer service and aftersales service functions EDW 1503 VGA Deren A AS LD1 LD2 LD3 LD4 LD5 LD6 mLD10 TO ME S1 S2 S3 84 S5 S6 SO Which function Selection of special mode customer or service On en of the special mode of special function description switch on appliance simultaneously rd with ON OFFSO gt and keep them GH z u see page B 11 pressed until H SES wes see page B 12 N Bei Aufruf der Kunden Funktionen darf press see page B 13 generell kein Sp lprogramm gew hlt sein key S3 keys S1 S3 press econ ii switch on appliance with ON OFF SO are flashing key S1 pag kay 52 see page
6. 16 A esse 18 A A G 20 In and Output Elements onneonnneenesnunnesrnsrrrrerrrsrrrrrerrerrrrrerrerrne 20 General laten E le ii Ean 21 Input philosophy Program Selection ccccccccc cece eeee seen eee eeee es 22 Input philosophy Select start me 23 Input philosophy Program sequence cece cece eee eeeeeee eee es 24 Input philosophy delete program ocooccooccccnooccocncccnooncccnonoconnno 25 Input philosophy alter program oocooccoccccnocccocnconcccnonncocnnnnnnos 26 Input philosophy alter program oocooccocnccnccccocnccncocnocnconnnnnnnos 27 Input philosophy interrupt program 28 IABUEPNIOSORNY DIS DIAV EE 29 Overview of customer and aftersales service functions 30 Servicefunction Adjust water hardness eereeeerrreren 31 Deactivation of rinse aid addition uenesnenennsersresrerrerrerrerrere gt 32 Deactivation of signal sound 33 fault memory and single actuator selection 34 LED test with integrated deletion of the fault memory 35 Manufacturing test routine ooccoocccocccccnncccnnnocnnnncncnnnnonencnonnss 36 Overview of error diSPIAYS 0 cece cece eccc cece eeeee cece eeeneeeneeeenes 37 Tele Le 39 electro CIFCUILGIAGQKAM are 39 A A e o oe 40 17 19 599 515 184 EN 1 Control panel Ee NZ aro wan EX Hu o FAVORIT ef AEG TROD CT TT I 7
7. B 15 key 53 see page B 16 ress eg 82 en see page B 17 ress eg cesa SPEE Who setting of water hardness deactivation rinse aid addition deactivation signal sound Areadout of fault memory single actuator selection LED test with integrated deletion of fault memory manufacturing test routine deactivation Pulse Wash additional washing cycle anu 30 6 11 Service function setting of water hardness General information Setting and changing the water hardness area is executed in all designs resp key arrangements analogously For that you always have to use the keys SO S1 S2 and S3 independent of their variant depending program load Key S1 is ALWAYS the water hardness area key The water hardness area value 4 is preset by the manufacturer With setting 1L it is generally not regenerated A salt addition is not necessary A possibly existing salt LED is not selected Electronic and mechanical setting with the appliance In addition to the electronic setting on the control panel described on the right you also have to pay attention to the mechanical setting in the appliance by the 2 step blending switch see for that the table for hardness area values Verschneide schalter EDW 1503 VGA LD1 LD2 LD3 a 99 eessen J 10 lu o Table for hardness area values Anzeige Anzeige Einstellung der Display Ende LED H rtestufe Wasserh rte Bemer
8. Pe A eu 1 Stunde A E E E GE VariantB gt ea een pa Display blinkt H 1 2 like variant A E 5 mit SE car E 3 Actuate start time preselection key in gt ll Z SZV LED is lit WEEN adjusted start time is flashing ER puni Any additional key pressure causes the start time scrolling by 1 hour Moss 3 Sekunden 1h 2h 3h 19h display off SZV 0h Ih 2h KS o m i With the setting Oh all LEDs of program and option keys are lit i o A SEEN o 4 Indication of SZV is flashing in the display until a washing cycle 6 nm ees o will be selected additionally The selected start time is not active SSerungen i E SE Ann 5 Select program by pressing the corresponding key Startzeitvorwahl l uft ab gt LEDs of progra and SZV a lit 6 A S E TR i ve eo SEN oan Run time to be expected is flashing Ma E TI 6 3 seconds after the last actuation of any key the adjusted start O a zen bessen time gets active and runs down after the door has been closed St rtseiivorw hllauft b H LEDs of program SZV and start time are lit in the display 23 6 5 Input philosophy program run A special feature with fully integrated appliancesis the condition that there are no control and display elements visible when the door has been closed That is why important information for the customer such as the cycle end or information on faults are indicated acoustically in addition This results in a few diff
9. S1 to S6 to select programs or options with the corresponding LEDs All keys are free and can be programmed without any restriction by the programming of the appliance variant 2 5 digit display and 3 LEDS LD10 TO LD12 A Absolutely necessary minimum equipment Keys SO ON OFF and the first 3 keys S1 to S3 with the corresponding LEDs and display The keys S1 to S3 are absolutely necessary to select all customer respectively service functions such as setting of hardness e Variant depending existing equipment Indication of start time by 2 5 digit display Indication between 1 and 19 hours in steps of 1h Indication of remaining run time bys 2 5 digit display indication of maximum run time 199 LED display for salt LED display fo rinse aid LED display for water tap closed LED display for END e Functions which can be adjusted variably by the customer via the control panel see description page B 11 13 Indication and alteration of water hardness by display and acoustic output Activation deactivation of rinse aid addition Indication by display Activation deactivation of signal sound for end Indication by display e Miscellaneous regeneration depending on need manufacturing test routine various service functions fault memory single actuator seletion design of appliance for max energy label AAA alternatively with or without fan drying aqua control system in different versions depending
10. WACH IN GERMANY El INTENSIV ae Bam ES Cu oe FAVORIT a Fe Ee AEG ees E ER TUEBODAY m r Mate iM ARMANI 2 Dimensions Build in dimensions for Integrated Dishwashers OKO FAVORIT 570 _ Bt k 820 870 w f 110 S S max gt x qe o may o 816 880 Appliances with height adjustable feet Plinth height for appliances 820 mm high 100 175 mm Plinth height for appliances 870 mm high 150 230 mm 09 2002 R K 3 lt 599 515 184 EN 3 Components 3 1 Electronic On electronic models a micro processor controls all components this is done using triacs The electronic also memorizes all programme data The heating is switched by a relay on the electronic board 3 2 Circulation Pump The circulation pump is driven by an asynchronous motor with an auxiliary winding The auxiliary winding ist in circuit with a 3 mF capacitor A tacho generator is used for speed control There are three speeds for rinsing 2800 1 min 2200 1 min 1900 1 min 1700 1 min 1600 1 min Power output 50 W Only for models with ceiling spray arm 3 3 Drain Pump The drain pump is driven by a synchronous motor Power output 26 W Pump rate 15 l min 3 4 Flow Heater The flow heater heats the water to the required temperature During the wash cycle water is contantly passing through the flow heater Power output 2000 W Resistor 25 0 Protector 98 C 5K Thermal fuse 260 C 05 2002 R K _4
11. electronics programmation Blocking by dishes or cutlery basket Nozzles clogged drive nozzles at spray arm extremities Spray arm leaking welding seam Spray arm bearing blocked dirt foreign bodies Screens in the appliance clogged Bellows at connecting pipe not sealed at recipient rear wall bellows not contacting glued together Circulating pump does not reach full power nominal speed is not reached due to winding influence Too little water in appliance for possible causes see Error codes i10 and FO Foam production in the appliance splashed rinsing liquid leaking dosing unit or con compatible detergent rinsing agent used No magnet in spray arm No spray arm detection Spray arm detection sensor faulty Wiring faulty turbidity sensor defect Wiring faulty turbidity sensor dirty Foam production in the appliance splashed rinsing liquid leaking dosing unit or con compatible detergent rinsing agent used ea Faulty electronics communication faulty A Wiring faulty y e i i i f Sireul tioh Bumprnallunelion Circulating pump capacitor defect u Circulating pump deenergized faulty wiring or no activation by electronics No tacho signal Tachometer generator defect recognized Wiring faulty Problem with water inlet in general see Error code i10 pipette effect in particular also look for an error memory entry i10 Water is not pumped off Water level inside appliance is not detected Upper spray arm does
12. leave the special program as follows EE z After 60 seconds all LEDs of the program and option keys AUS nach 60sek automatisch are lit automatically The indication in the display goes out The appliance is in the prestart mode again nn ae or P S i the appliance is switched off by ON OFF key SO eet EE AUS durch manuelle Bet tigung ber Ein Aus Saving the set condition The currently valid condition is saved directly after any entry 32 d When calling the customer functions no washing cycle must be selected generally 6 13 Customer function deactivation of signal sound General information Calling changing saving the signal sound deactivation The function deactivation of the signal sound does not exist 1 A ae gl Calling the function signal sound deactivation generally and must be programmed in the software a g a aoar g a e 1 Appliance in switched off condition variant un LD1 LD2 LD3 LD4 LD5 LD6 11 pue 2 Switch on appliance with ON OFF key SO prestart mode Deactivation resp activation of the signal sound is executed a al a Y All LEDs of the program and option keys are lit in all designs resp key arrangements analogously eene 2 For that you always have to use keys SO S1 S2 and S3 independent of their variant depending program load So E Key S3 is ALWAYS the signal sound deactivation key The signal sound is always set active by the manufacturer
13. not rotate turbidity signal faulty Time limit during filling Problem by incomplete pumping in previous program cycle remaining water see Error code i20 also look for an error memory entry i20 exceeded Improper loading e g big item pot bowl is reversed and fills with water Foam production in the appliance splashed rinsing liquid leaking dosing unit or con compatible detergent rinsing agent used 6 Wirings 8 1 Circuit diagram Gm Va bulsuas buisuas 1000 E Eo 19 N ZO f i LO d SR 1 N d eu ZO Zd Lo 35H OU ul al St ad Gi TOU ch LO D A a EES A D kk ZY 19 y CEE VA VA V VA ke y9 LOIN Y ld DO h 9 19 D LI g ra al va oJ a LI A OY PPP e e LU 0 gt SI II TA rm WW u a cl Ness NJ JADAN 2696 2990 Io N wo pundzing x 99DJ19 U Jos 999 515 184 EN 39 09 2002 R K jagram d iring 8 2 W JAWA OW HLYV3 ent e T2 A A Io JAVA es JIN av LI e GEI D 35 n SE eee re Er ee El le gt iz 2k la 2 gt 1 00 19 IL ALL X HILIMS JUNSSIUA ul 5 9 s A p EEE i gt Jos YOLNAIULSIO TEE OHIVL HLUY3 aly 3SNIY IN39Y3130 ae E dHNd TAN en Gm H EIN a Y31V3H t bw ny ME n H Wi lun ti ji ind E wi H il z z S e RI u F al l la lt il D aa IN 1 lt Be fe le Hers lo af i 218 le OD e alH Pal aa o oF gt Di d IK Di In
14. vent Sump assembly 599 515 184 EN 5 2 Water Inlet The water flows into the regeneration dosage chamber 7 via inlet valve 1 over air break 2 into regeneration dosage chambers 3 into softener 8 At this point the water divides 1 4 of the water enters the tub through the vent 23 3 4 of the water enters the sump 24 through hose 6 The level control chamber built into the sump operates the pressure switch 15 1 Inletvalve 10 2 Air break 11 3 Regeneration water dosage 12 4 Overflow safety level 13 5 Safety overflow 14 6 Inlet to sump from regeneration dosage chamfer 7 Regeneration dosage chamber 16 8 Softener 17 9 Salt container 09 2002 R K Non return valve salt container Regeneration valve Safety inlet hose Basetray Float switch Pressure switch Filter Circulation pump 15 Flow heater Drain pump Non return valve Sprayarms Roof mounted shower Tub vent Sump assembly 599 515 184 EN 5 2 1 Water load steps Example static water dynamic water 4 max 4 load el load S repetitions to level with level control Timeout 1 Timeout 2 speed min target speed lt 10 Sek se Sek gt lt 5 Sek gt 220 Sek level check water failure displayed if level not reached level check water failure displayed evel not reached dynamic water load ca 1 6 static water load filling
15. E Electrolux SERVICE MANUAL DISHWASHER DIVA EDW 1503 o EEE FAVORIT oY we m S Ge Gol Pt AEG ES Dishwasher Electrolux Publ Nr DIVA Muggenhofer Stra e 135 599 515 184 D 90429 N rnberg EN gt German EDW 1503 Fax 49 0 911 323 1022 Spares Operation Ausgabe 09 02 R Kurzke Index 3 1 3 3 3 4 3 5 3 7 3 8 3 9 3 10 3 11 3 11 1 4 1 4 2 9 1 9 2 9 2 1 9 3 6 1 6 3 6 4 6 5 6 7 1 6 7 2 6 8 6 10 6 11 6 12 6 13 6 14 6 15 6 16 6 17 8 1 8 2 09 2002 R K COMMON DANS EE 3 DIMENSIONS zarr se se O ers taal a a a lee 3 COMPONEN Sian 4 EE EE A Circulation 910 aa Dr a et la a ra a 4 BN A O mele rere ne ote era Reena es nee 4 OW INCAS PP 4 Detergent dispenser 01nsannnnnnnnanoennansnirerrniorrrrrrnrrrrrrrrerrrrrsrrne 5 INCHING INN SCNSOR nee sein 6 PRESSUTE SWIICH PE POINT 6 Intertetenee TS arado darla 6 opravy als id a ica T DA A E E E E AA T Regeneration dosing with condensor occooccocccccncocnnoccnoncncnconnnos 8 Water softening regeneration ccc ceccceecceeeecceeeeeseeaeeetanees 8 Repair Mio MAIN ee 9 Open The NOUSIN EE 9 Position of the components asirese AE 10 Watercourse Scheme rn an ee ee ine 13 All Around Water Protection 0ccc cece cece sec eeeceeeeeeteeeneeeaeenees 14 Water IM AKS ates il 15 Water load steps annononnonuenennsrensnrsrerrsrrrrrrrsrrnrsrrrrerrsrrrrrnrerrerne
16. all the next step and indicate it in the display as follows 2 actuation Display of second value of the fault memory Seet 3 actuation Display of third value of the fault memory 4 actuation Display 4 selection of regeneration valve 0 Anzeige 2 3 Fehlers LD1 Display und LED blinken 5 actuation Display 5 selection of drain pump o pro Tastendruck 6 actuation Display 6 selection of valve 1 Weiterschaltung ger ger A filling to level if level already existing no filling 5 Codierte Anzeigen 7 actuation Display 7 selection of heating nu only when level detected 1 8 actuation Display 8 selection of circulation pump tot Display und LED binken nee 9 actuation Display 9 selection of detergent dispenser 6 lf z a a 0 g 10 actuation Display 10 selection of drying fan N BEER FL zen T e see description page B 19 Survey of fault displays It is generally valid E EE All positions can be called scrolling as many time as one wants For calling all service functions you always have first to actuate function keys S1 and S3 before switching on pao e irren bass ee l The several steps are switched onward manually by pressing the applianceby ON OFF switch SO DUC any key If the function key S1 is not pressed within 60 seconds The keys have to remain pressed about 3 seconds eege LSO the service function is left automatically All LEDs of the to activate the function a a program and
17. am and option Fe Damna aD ADMa keys are lit The program is deleted ee E Meere er The appliance is in the prestart mode 25 6 7 1 Input philosophy alter program o a T99 KEE T A SO et e Alter program during the prestart mode The door is still open at that moment Pisplay A 1 Program has been selected but did not yet start ZE Corresponding program LED is lit Ld Presumable run time is flashing in the display SE d By pressing the new desired program key shortly it is possible to alter directly e Options already selected before are cleared and have to be selected anew d a New selected program LED is lit Presumable new run time is flashing in the display O 3 Before the door has been closed it can be altered as many times as one wants Only when the door has been closed the program will start automatically Special feature when a start time was selected before 1 Program and start time have been selected but did not yet start LEDs of program and SZV are lit Programmed start time is flashing in the display 2 By pressing the new desired program key shortly it is possible to alter directly The start time preselection already selected is preserved after the alteration Program options already selected before however are deleted an
18. cally The key LED LD3 continues flashing H The display is now indicating the expected run time paeis From that moment the same input philosophy is valid for the C manufacturing test routine as for normal washing cycles cycle run and cycle end see description page B 5 delete cycle in advance see description page B 6 interrupt program see description page B 8 Overview Errors Displayed Applicable for EDW1500 1503 VGA EDW1100 1003 VGA EDW2000 Display Display Acoustic Error Display Call aed e Output via on by Indication visible for Error Memory indicator Lari Short Explanation What happens Screen END LED No of Beeps Customer Service CAVAT STRN 2Hz 5sec Pause 2Hz 5sec Pause i If available for If available for EDW 1500 EDW1100 model this model Switchpoint of pressostat is not reached Programme stops and can be continued after error remedy by after max 60 secs pressing the programme key If fault is not corrected and programme only in programme steps incl Filling up to level key is pressed the machine runs dry until next subprogramme LED Water Reset point of pressostat is not reached after max 120secs Programme stops and can be continued after error remedy Programme stop by pressing the programme key Programme stops and restarts automatically when error has terminated EL ER oap ow a es cn JE flashing Ren T yd d N Aqua Control System s
19. d must be selected anew New program LED and SZV LED are lit Run time to be expected is flashing in the display for 2 sec afterwards the start time is flashing again If the selected start time is already running down the time is permanently lit in the display you have to press the new desired program key a longer time about 6 seconds for alteration 26 6 7 2 Input philosophy alter program EDW 1503 VGA V Mi SO e Alter program after program start Bene E 1 To alter a program you have to open the door 2 Program is stopped by opening the door Corresponding program LED is lit Run time is indicated in the display 3 Y O A 3 Actuate key of the new desired program in our example S5 for about 6 seconds Ea DS Ll Display LED of running program starts flashing eee de nn Z Run time is indicated in the display Display blinkt u FE ea a MU E 4 After this time the previous program LED and the program LED of the new E 110 mm O desired program is lit The display indicates the run time which is to be expected anew flashing 5 The cycle will start automatically when the door has been closed If a program is altered after an already started cycle the new cycle starts generally from the beginning This is also indicated by the run time in the display Optio
20. dicated in the display and in addition acoustically see for that the table on the left side of this page Changing the set hardness Any other actuation of the function key S1 changes the hardness area This increases the value scrolling 4L 5L 6L 10L 1L 2L Leaving the function After the last key pressure of function key S1 you can leave the special program as follows After 60 seconds all LEDs of the program and option keys are lit automatically The indication in the display goes out The appliance is in the prestart mode again or the appliance is switched off by the ON OFF key SO Saving the set water hardness The selected hardness area is saved directly after any entry d When calling the service functions no washing cycle must be selected generally 6 12 Customer function deactivation of rinse aid addition General information Calling changing saving the rinse aid addition deactivation The function rinse aid deactivation does not exist generally eu LD1 LD2 LOS LD4 LD5 Loun Calling the function deactivate rinse aid addition and must be programmed in the software variant i _ A 0 1 Appliance in switched off condition Deactivation resp activation of rinse aid addition is executed a Dies DaB Dede ee 2 Switch on appliance with ON OFF key SO prestart mode DANA AMMA 7 S in all designs resp key arrangements analogously S u A Eo All LEDs of the program a
21. erences for the start run and end of a cycle in comparison with normal upright substructure resp integrated variants of appliances e Cycle start The cycle starts finally when the door has been closed After the door has been closed and the cycle has started successfully it is no more possible to make any alterations etc But to make changes in the program setting in exceptional cases you have to open the door during the running cycle cancel resp delete cycle see description page B 6 Delete cycle change resp alter cycle see description page B 7 2 Reselect cycle e Cycle run As already described above there are no displays visible with VGA appliances caused by the type of construction The optical displays are selected but not hidden by the worktop The LEDs of the selected washing cycle are lit during the whole cycle run The display indicates the still remaining washing time in minutes The run time is updated depending on the program The update is executed in changes of program parts In doing to the run time can correct in jumps downward or the display is stopped until the time will be synchronized again e Cycle end A As already described above there are no displays visible with VGA appliances caused by the type of construction The optical displays are selected but hidden by the worktop When the cycle has ended an acoustic signal will sound The acoustic end signal is a whistling sound
22. fthe inner hose should burst the water passes into the tub The safety pressure switch activates the drain pump and decreases the waterlevel down to normal level An additional overflow protection is a defined overflow through the regeneration chamber The water flows into the bottom tray and activates the float switch which energises the drain pump This drains the dishwasher preventing water damage Safety level If the safety level is reached by over fillling the safety pressure switch starts the drain pump The water is only drained until it has reached the normal level because the reset point of the safety pressure switch is above the switchpoint of the normal pressure switch Leakage Protection The anti flood switch in the base tray will activate the drain pump and drain the water from the tub in the event of an internal leakage If the float switch is activated all electric components are switched off except the electronic and the drain pump 1 Inletvalve 10 2 Air break 11 3 Regeneration water dosage 12 4 Overflow safety level 13 5 Safety overflow 14 6 Inlet to sump from regeneration dosage chamfer 7 Regeneration dosage chamber 16 8 Softener 17 9 Salt container 09 2002 R K Non return valve salt container Regeneration valve Safety inlet hose Basetray Float switch Pressure switch Filter Circulation pump 14 Flow heater Drain pump Non return valve Spray arms Roof mounted shower Tub
23. hardness of up to 70 dH 05 2002 R K 8 599 514 DE 4 Service tips 4 1 Open the housing To remove side panel remove fixing screws pull the panel away from the rear and gently out of the front trim pic 1 You need Torx epuipment Remove the screws 1 to pull the outer door away To remove the panel remove the fixing screws 2 N_ 2 Removing the cover plates of the base area remove these screwst Abb1 2 y 05 2002 R K 9 599 514 DE 4 2 Position of Components Detergent dispenser 1 IM l Hr In ms Spray arms 2 ff re Kar Roof mounted shower 3 Salt container 4 Filter 5 o5 mu Type plate 6 Electronic EDW 1503 1 and ON OFF switch 2 are clipsed Detergent dispenser 3 Thermal sensor 4 Drain pump 5 Pressure switch 6 05 2002 R K 10 599 514 DE Back side view Flow heater 1 Terminal box 2 Inlet hose 3 Drain hose 4 Water inlet for above spray arm 5 Removing the detergent dosage chamber disengage locking tabs 1 disconnect hoses 2 holding the top of the chamber pull upwards disengaging it from the softener Removing the softener unit remove the securing nut located under the salt cap press softener 1 down and remove it through the front from the base area CAUTION if accessible release reed switch 05 2002 R K BER 599 514 DE Removing the base remove
24. he program will be deleted When the door has been closed the appliance will be automatically again in the prestart mode A new program could be selected again immediately Switching off the appliance by pressing the ON OFF key SO also deletes the current program from that moment see description page B 3 Input philosophy program selection e What happens in case of resp after a power failure Incase of a power failure the appliance behaves as when switched off using the ON OFF key see description above under Interrupt program After the mains have returned the appliance behaves as after being switche on using the ON OFF key SO After a power failure the cycle continues without any necessary key actuations 28 6 9 Input philosophy displays All displays are designed as LED displays and are available depending on the appliance variant Start time preselection and run time are indicated via a display only with the EDW1503 A special feature with fully integrated appliances is the condition that there are no control and display elements visible when the door has been closed e Displays for program selection and options Above resp next to a program or option key there is generally a corresponding LED to confirm the selected function They are lit permanently during the whole cycle run e Display for start time preselection SZV The start time preselection is indicated via a 2 5 digit display The di
25. ion LD1 LD2 LD3 LD4 LD5 LD6 aLpi0 Calling the function manufacturing test routine In the service function mode the key S3 is ALWAYS 2 responsible for calling the manufacturing test routine EDW 1503 VGA LD1 LD2 LD3 is EE LD1 LD2 LD3 alle blinken b A CH j 4 MODAN IAN Bee L 21 Fertigungspr fprogramm l uft As is generally valid For calling all service functions you always have first to actuate the function keys S1 and S3 before switching on the appliance by ON OFF switch SO The keys have to remain pressed about 4 seconds to activate the function This procedure is intentionally different to that for the customer functions 1 auto C a O en SE Zu 1 Appliance in switched off condition S eS g 2 Press keys S1 and S3 simultaneously and switch on the appliance by ON OFF switch SO For that keep the keys S1 and S3 pressed until the 3 confirmation LEDs LD1 LD2 and LD3 are flashing A temporary flashing up of LEDs is possible and no fault 5 By actuating the function key S3 you can call the manufacturing test routine The key LED LD3 continues flashing LEDs LD1 and LD2 go out The presumable run time is indicated in the display flashing 6 The test routine starts automati
26. ion dosage chamker Pressure switch 23 Tub vent 7 Regeneration dosage chamber 16 Filter 24 Sump assembly 8 Softener 17 Circulation pump 9 Saltcontainer 09 2002 R K 18 599 515 184 EN Sequence draining with pressure switch level check drainpump 1 draining sequence with variable timing on off T1 variable T2 variable T3 variable Drain Cycle T1 T2 T3 First draining before every wash cycle 45 sec 15 sec 20 sec Draining after the wash cycles 30 sec 20 sec 10 sec New draining with sequence draining The draining step contains of 3 time sequences In the middle sequence during time T2 the drain pump is stopped At the end of the drain step the water level is checked If the switch back is reached the drain step is terminated If the switch back isn t reached the drain step is repeated A failure code is displayed if after 2 drain steps the switch back couldn t be reached In this case the program is stopped 09 2002 R K 19 599 515 184 EN 6 Electronic EDW 1503 6 1 In and output elements e EDW1503 Display LD14 29 LDI LD2 LD3 LD4 LD5 LD6 epp l 1 Ss E S1 S2 S3 S4 S5 S6 09 2002 RK 20 ON OFF Switch 599 515 184 EN 6 2 General information EDW 1503 VGA e Equipment in the panel area O LL a a ee ey DVI i see description page B 1 EEE Bu LS Possible equipment Separate ON OFF switch SO without optical confirmation 6 keys
27. is possible time in Sek Static filling Static filling until pressure switch point failure code If this point isnt reached after max 2 minutes Timeout 1 a failure code is displayed and the program is stopped Dynamic filling 10 seconds filling at reduced circulation pump speed 5 seconds pause The target 10 seconds filling at reduced circulation pump speed speed is filling with increasing circulation pump speed As soon as the dependent on target speed has been reached it is filled up to the pressure the subsequent switchpoint pulse wash Failure code If this dynamic switchpoint isn t reached within total 4 minutes Timeout 2 the dynamic filling can be repeated 3 times Only after non successful repeating 3 times a failure code is displayed and the program is stopped pulse wash pulse 2800 1 min Pause 1600 1 min target speed in dynamic filling 2200 1 min 1900 1 min 1700 1min 09 2002 R K 16 599 515 184 EN New pulse wash with random functionality speed SE nn KEEN Ee variable APS AMA ee AA RR 1600 an Thigh r Tiow Thigh r Tiow Thigh time 0 insec random function The variable speed is Thigh r ti hi h nd ti l D u 1600 1 min at the war moment and equal to all E SE appliances level i pressure switch point water level nn Insec Random function T time for high speed calculated with random funktio
28. kung egami LD1 LD2 LD3 LD4 LD5 LD6 WALAA EAAS AZA A AAAA NA ef i GE E a A A i y Mi 7 IS Y H CH in mmol L 1L kein Regenerieren 2L 3L 4L 5L 6L 7L bis 36 8L 37 bis 42 aL bis 50 10L 10 mal 10 51 bis 70 3 0 bis 125 doppelt Regenerieren d When calling the customer functions no washing cycle must be selected generally Calling changing saving the electronic hardness area value 1 q LD1 LD2 LD3 LD4 LD5 LD6 EZ r 11 I I 7 II S EE LD1 LD2 LD3 LD4 LD5 LD6 23 AA A AL HAN Ia i Bu ao Jemen a women mE Gi Gin in MAA ELA UA blinken ehe ert DAN Daunen nee ann at AATAS TAMT AAA 1 1 Ge i D LD1 i un blinkt Ss Pro S1 Tastendruck nt 1 Stufe l Ausgabe a Eg akustisc U U SS E e A E H y pu q AUS durch manuelle Betatigung Uber Ein Aus 31 Calling the function set water hardness 1 Appliance in switched off condition 2 Switch on appliance with ON OFF key S0 prestart mode All LEDs of the program and option keys are lit 3 Press keys S2 and S3 simultaneously until the confirmation LEDs LD1 LD2 and LD3 are flashing 3 By actuating the function key S1 you now can call the water hardness function The confirmation LED LD1 continues flashing LEDs LD2 and LD3 go out The set hardness area is in
29. ly until the 3 confirmation LEDs LD1 LD2 and LD3 are flashing A temporary flashing up of LEDs is possible and no fault 5 By actuating the function key S2 you now can call the function All LEDs and 188 in the display are flashing about 30 seconds Leaving the function deletion of the fault memory When all above mentioned LEDs resp the display have been flashing for about 30 seconds the function will be left automatically All LEDs of the program and option keys are lit The indication in the display goes out The appliance is in the prestart mode again The function can be left even earlier by switching off the Au is generally valid For calling all service functions you always have first to actuate the function keys S1 and S3 before switching on the appliance by ON OFF switch SO The keys have to remain pressed about 4 seconds to activate the function This procedure is intentionally different to that for the customer functions 35 AUS durch manuelle Bet tigung ber Ein Aus appliance by ON OFF key SO SO In any case the service fault memory is deleted 6 16 Service function manufacturing test routine General information 4 4 Calling the service functions is executed in all designs resp key arrangements analogously For that you always have to use keys SO S1 S2 and S3 independent of their variant depending program load Calling above mentioned service funct
30. n T time for high speed cycle definition T random time time for low speed Ratio factor for low speed eeprom definition Circulation The circulation pump 17 pumps the water simultaneously into the ceiling shower 22 and into both spray arms 21 The water is filtered in the sieves 16 and led to the circulation pump Function of the new pulse wash with random functionality After the filling steps the circulation pump is running at two rotational speeds Pulse Wash Pulse time 2800 1 min Pause 1600 1 min Use with Wash Cycles Definitive Time Random Time Definitive Time Random Time 1 0 9 sec 0 0 3 sec 0 1 5sec prewash intensive The ratio of pulse I en time and pause is a aan Ee a EE D a normal aa owe e Powe fe 09 2002 R K aI 599 515 184 EN 5 3 Draining During the wash cycle the water is pumped out at various stages First the draining water cleans the filters 16 The filters are open at the bottom which allows any soilage to be rinsed off sufficiently There is a non return valve 20 at the inlet connection to the drain pump 19 This valve prevents the water 1 Inletvalve 10 Non return valve salt container 18 Flow heater 2 Air break 11 Regeneration valve 19 Drain pump 3 Regeneration water dosage 12 Safety inlet hose 20 Non return valve 4 Overflow safety level 13 Basetray 21 Spray arms 5 Safety overflow 14 Float switch 22 Roof mounted shower 6 Inlet to sump from regenerat
31. n the door has been closed the program starts automatically Corresponding program LED is lit Run time is indicated 22 6 4 Input philosophy select start time Variant A Variant B time preselection after program selection time preselection before program selection T aaa toi ibe ibs toa io ioe ee Fi Variant A D 2 7 Ler is 1 Appliance in switched off condition Pa en 2 Switch on appliance with ON OFF key SO gt tonnes LD LD DO ADA AD DB pm Appliance in prestart mode See Zei N E All LEDs of program and option keys are lit a e aa the keys can be selected EE Display blinkt 3 Select program by pressing the corresponding key E A gi al Corresponding program LED is lit E m Run time to be expected is flashing ame UNE 4 5 Actuate start time preselection key within 3 seconds Display blinkt Ai a m pe err ee Y The keys of program and SZV are lit Don A a SS Adjusted start time is flashing ELEN OS Oon mu zz Any additional key pressure causes the start time scrolling by 1 hour EN GE Display blinkt 1h 2h 19h display remaining run time SZV 0h 1h 2h 1 Stunde A 6 3 seconds after the last actuation of any key the adjusted start RR BA time gets active and runs down after the door has been closed or AN i Pro Tastendruck LEDs of program SZV and start time are lit in the display
32. nd option keys are lit For that you always have to use keys SO S1 S2 and S3 AP A i S0 independent of their variant depending program load e eh 3 Press keys S2 and S3 simultaneously until the Key S2 is ALWAYS the rinse aid deactivation key 3 ily Ban Ban GEHE confirmation LEDs LD1 LD2 and LD3 are flashing The rinse aid addition is always set active by the manufacturer a i LI _ 4 By actuating the function key S2 you now can call the function rinse aid addition The confirmation LED LD2 m continues flashing LEDs LD1 and LD3 go out LI The current condition whether the rinse aid addition is E active or not is indicated in the display 1d rinse aid addition on Od rinse aid addition off Ifthe rinse aid addition is deactivated it means that no more rinse aid is added via the detergent dispenser Along with the deactivation a variant depending existing 4 rinse aid LED is deactivated generally EDW 1503 VGA gt o SEN o o a e e Deactivation resp activation of rinse aid addition 1 99 SS SS E A ne 5 6 By any further actuation of the function key S2 you activate Eo a rn 6 a resp deactivate the addition alternating Tue an Leaving the function After the last key pressure of the function key S1 you can TEE LD1 LD2 LD3 LD4 LD5 LD6 pic N pOREE RZ SHIRT de Ne e
33. ns already selected before will be deleted and must be selected anew 2 6 8 Input philosophy interrupt program e Interrupt program Using the ON OFF key SO it is possible to interrupt the program as long as one wants The same is valid for an interruption by opening the door There is no deleting function integrated in the ON OFF key SO Ifthe cycle is interrupted by using the ON OFF key all displays go out The cycle run is continued by switching on using the ON OFF key SO resp by closing the door without that another key actuation becomes necessary Information The cycle is continued with a short time delay All displays and confirmations appear in the same condition as before the interruption e What happens when opening and closing the door The appliance is switched on and in the prestart mode After opening the door all indications keep to be displayed on the panel The power supply of the electronic is fully guaranteed as long as the appliance remains switched on The door is opened during the running cycle After opening the door all indications keep to be displayed on the panel as long as the appliance keeps to be switched on by using the ON OFF key SO After closing the door the appliance will start automatically and the cycle run will be continued Attention When the 1 regeneration has been reached in the program part drying it is valid When the door is open longer than 30 seconds t
34. on electr and mech components and the corresponding variant programming start time preselection half load small quantity as automatic system or with key additional washing cycle 3 in 1 special tablet program e Possible selectable program options 4 4 4 senitize 21 EDW 1503 VGA LD1 LD2 LD3 LD4 LD5 LD6 LD10 6 3 Input philosophy program selection T SSS g bi LD2 LD3 LD4 Lbs LD6 ann f 1 Appliance in switched off condition SSS CT ae ENEE oJ en ibas us 2 Switch on appliance with ON OFF key SO prestart mode 2 TR 2072 Appliance is in the prestart mode ITT t ITT n DE Ten All LEDs of the program keys and the SZV start time preselection key are lit the keys can be selected Selection of a start time possible see description page B 4 Input philosophy start time preselection 3 Select program by pressing the corresonding key Corresponding program LED is lit run time to be expected is flashing Within 3 seconds it is possible to alter or additionally select an option ee Selection of a start time possible see description page B 4 Input philosophy start time preselection 4 Program starts only when the door has been closed Up to this moment it is possible to alter or additionally select an option at any time Whe
35. option keys are lit The indication in the display This procedure is intentionally different to that for the EE E goes out The appliance is in the prestart mode again customer functions m n ae i It is also possible to leave the function by switching off the NAAA INN E appliance by ON OFF key S0 AUS durch manuelle Bet tigung ber Ein Aus 34 6 15 Service function LED test with integrated deletion of the fault memory General information LD1 LD2 LD3 LD4 LD5 LD6 opio 1 101 pg n l 1D12 Calling the service functions is executed in all designs resp key arrangements analogously For that you always have to use keys SO 1 S2 and S3 independent of their variant depending program load In the service function mode the key S2 is ALWAYS responsible for the function LED test with integrated deletion of the fault memory EDW 1503 VGA LD1 LD2 LD3 o II WT WW 1 TI 7 S1 S3 etnia Display und alle LED blinken 5 AAA ERAN ASA AAAA AAU i 183 S Re Se ae Calling above mentioned service function Calling the functions LED test with integrated deletion of the fault memory 1 Appliance in switched off condition 2 Press keys S1 and S3 simultaneously and and switch on the appliance by ON OFF switch SO For that keep the keys S1 and S3 pressed simultaneous
36. ows into the rinse tank 05 2002 R K D 599 514 DE 3 6 NTC Temperature Sensor Resistor 9653 Ohm 4843 Ohm 1204 Ohm 445 Ohm 3 7 Pressure Switch The pressure switch controls the water level Without water contact 11 12 is closed fN Switch point with level 65 mm Ws Reset point with level 45 mm Ws The pressure switch is not adjustable 3 8 Interference Filter The interference filter is connected in the terminal board paral lel to the mains feed 05 2002 R K 6 599 514 DE 3 9 Spray arms The new cutlery basket is placed at the upper diswasher basket The celling sprayarm sprays the water directly onto the cutlery basket and tguarantees an excellent washing result with the cutlery placed in that basket Celling spray arm 3 10 Drying fan The new drying fan is located at the top on the rinse tank Function mode of the condensing drying Rinse tank fan and regenerating dosing with condenser form a closed circuit The humid air is sucked from the top of the rinse tank and blown through an air guide between rinse tank and regenerating dosing Thereby the air gets dry and the condensate is guided to the drain tub The dry air gets through the rinse tank ventilation into the rinse tank During the drying phase the condenser is additionally cooled with 1 liter of water 05 2002 R K upper spray a rm air guide for _ condenser rinse tank ventilation drain
37. rge hose siphon cover plug at siphon connection not removed during first commissioning Discharge hose bent or connection height above 100cm Ball valve in discharge trough glued blocked discharge pump does not aerate Pressure controller faulty Pressure controller hose obstructed or bent Insulation fault with heating element Leakage at recipient discharge trough hose system e g Y type hose regeneration dosage etc Inlet valve faulty does not close Water inlet too high faulty flow governor at inlet valve Connecting hose regenerating dosing to discharge trough blocked Water remains Water inlet channels in regeneration dosing unit blocked in base trough Overflow Screens in the appliance clogged also check spray arm nozzles for clogging Pressure controller faulty Pressure controller hose obstructed bent or leaking Pressure controller wiring is faulty Foam production in the appliance splashed rinsing liquid leaking dosing unit or con compatible detergent rinsing agent used Base trough is dry Inlet valve or wiring electrically interrupted Motor triac short circuit Faulty electronics Es Heating element faulty No rise in temperature Ss GES Heating element deenergized faulty wiring or no activation by electronics 7 Thermal sensor defect NTC signal fault 170 9 y Wiring faulty e g short circuit or interruption Mains filter defect Check sum error EEPROM Faulty electronics EMC problem Check sum error model S Faulty
38. side panels rear panel and plinth panel gently release base fixing clips with a screwdriver figure take off base carefully and release circulation pump electronic and heater relay disconnect the float switch With base removed following components are accessible Drain pump 1 Circulation pump 2 Flow heater 3 Temperature sensor Turbidity sensor 4 Pressure switch 5 05 2002 R K a2 2 599 514 DE 5 Water Course Scheme 1 Inletvalve 10 2 Air break 11 3 Regeneration water dosage 12 4 Overflow safety level 13 5 Safety overflow 14 6 Inlet to sump from regeneration dosage chamtier 7 Regeneration dosage chamber 16 8 Softener 17 9 Salt container ohne Sicherheitszulaufschlauch Ausf hrung Non return valve salt container Regeneration valve Safety inlet hose Base tray Float switch Pressure switch Filter Circulation pump Kurze Regenerierdosierung 09 2002 R K 18 19 20 21 22 23 24 Flow heater Drain pump Non return valve Sprayarms Roof mounted shower Tub vent Sump assembly 599 515 184 EN 5 1 All Around Water Protection Aqua Control Inlet Hose The inlet hose has a double wall construction The inner hose is equipped with a flow restrictor built into the tap connection and has a flow rate of 4 litres per minute The inlet valve 1 is located in the base of the dishwasher The safety outer hose 12 is connected to the regeneration chamber I
39. splay indicates the start time in hours The start time is counted down to Oh in steps of hours The start time setting is displayed scrolling 1h 2h 3h 19h Oh SZV off 1h 2h Z When the start time preselection has run down the display indicates the run time to be expected of the selected washing cycle in minutes e Run time display RLA The remaining run time is indicated via a 2 5 digit display The display indicates the still remaining washing time in minutes gt The run time is updated depending on the program The update is executed in changes of program parts In doing so the start time can correct downward in jumps or the display is stopped until the time is synchronized again e Information displays The LED position is depending on the programming of the variant They can be programmed toany LED which is not programmed with a program or option key The LEDs are lit permanently from switching on the appliance by ON OFF key SO until the momentof the started program Furthermore the LEDs are lit when the cycle end has been reached until the appliance is switched off The information LEDs go out during the whole cycle run LED display salt LED is lit in case of a lack of salt LED goes out when salt has been refilled Depending on the salt dissolution it can take some time until the LED goes out Information LED display salt goes out with hardness setting 1 no regeneration necessary
40. t of fault memory and single actuator selection General information Calling above mentioned service function Calling the service function is executed in all designs lui Up Di LD2 LD3 Lb4 Los LD6 arpio ft Calling the functions resp key arrangements analogously I SS Ll readout of fault memory and single actuator selection For that you always have to use keys S0 S1 S2 and SQ een M1m FL independent of their variant depending program load en 1 Appliance in switched off condition Inthe service function mode key S1 is ALWAYS responsible for the function readout of fault memory and single actuator selection Press keys S1 and S3 simultaneously and 3 4 and switch on the appliance by ON OFF switch SO For that keep pressed keys S1 and S3 until the 3 confirmation LEDs LD1 LD2 and LD3 are flashing A temporary flashing up of LEDs is possible and no fault EDW 1503 VGA EE a a dag 8 8 8 AAA LD1 LD2 LD3 5 4 Sekunden 5 6 By actuating the function key S1 you now can call the function EA The confirmation LED LD1 continues flashing LEDs LD2 and AE RE ee E A LD3 go out es E The first value of the fault memory is indicated in the display The display indication is flashing By any further actuation of the function key S1 it is possible e to c
41. tub DE 599 514 3 11 Regenerating dosing 4 with condenser cools down due to the cold incoming water Therefore another 1 liter of water is required during the drying cycle With every filling step the condenser ke mem 1 softener unit 2 regeneration dosage 3 11 1 Watersoftening regeneration chamber The water softening can be adjusted in 10 levels The incoming water flows until positon 5 to 85 through the softener which works according to the ion exchange principle The ion exchanger is filled with small epoxy resin balls The resins exchange the hardness constituents calcium and magnesium for sodium ions When all the sodium ions are used up it is necessary to regenerate the softener This is done by flushing a brine solution through the softener Afterwards the softener is washed out with fresh water and is now fully effective Depending on the water hardness regeneration is only necessary after several wash cycles The remaining 15 of water flow through the rinse tank ventilation directly into the appliance From setting of level 6 the whole water flows through the softener For this purpose you also have to set mechanically from O to 1 with the regenerating dosing With the setting of level 9 it is additionally regenerated after the washing in a rinse cycle With the settings 1 to 8 it is regenerated after the final rinse depending on need The softening system is designed for a water
42. witches off solenoid directly e Ze IN i A D A f e Recycling pump Triac short circuit NTC Sensor Tacho signals are recognized although rec pump is not Programme stops and water is filled up until reset point of selected pressostat During heating temperature rise by min 1 5K is not detected within 3min x Programme is continued until its end without heating function NTC short circuit or break Programme is continued until its end without heating function K Communication error with ext EEPROM x Check sum model programming MCF or Check sum CCF not OK Only recognized after switching on Programme selection not possible On Off LED is on co A e Se e H H e Wi aii e e A pr er r AS Pa er Pat e Ss WW D e Des eet hs Ss Ch ES CN Se ae i k T e ES al Fan S gas Pd Se a EN a a Fy S Pa Ge At programme start and each subprogramme start also after door open close or mains failure spray arm Error display until sprayarm speed is recognized rotation or if no control is checked and evaluated LED Spray arm The turbidity signal required for calibration Always recognition of turbidity is not reached with 15secs Programme sequence is adapted accordingly Communication failure with User Interface Machine stops waiting until communication is cleared Recycling pump selected but no tacho signal Recycling pump without control heating off recognized for 5
43. with the following interval 15 seconds on 3 minutes off 15 seconds on 3 minutes off 15 seconds on completely off The end signal is cleared immediately by opening the door The confirmation LED of the program key of the run down cycle is lit and the display indicates 0 These displays however are immediately deleted when opening the door When the cycle end has been reached it is possible to delete the run down cycle by opening the door After closing the door the appliance is automatically again in the prestart mode e a new program could be selected again at once In order to switch off the appliance completely you have to actuate the ON OFF key SO Even in this case the run down cycle is deleted All displays go out 24 6 6 Input philosophy delete program ere i S1 S 3 S4 Sp S6 A selected or already started washing cycle can be deletedat any time during normal operation e Delete program using the reset function Reset function always with keys S2 and S3 1 A A A LDS een IT mus Br IL 1 Cycle running blinkt es ac 2 Actuate reset keys S2 and S3 for about 2 seconds 93H pry Sl LED of the running cycle starts flashing ee EE ee The run time continues to be indicated 2 Sekunden rr E 3 After about 2 seconds all LEDs of progr
Download Pdf Manuals
Related Search