Pro-Series ECU
Contents
1. Part RY11841 ECU HFPWC H1 11 15 12 4 2010 08 FX SHO Models ONLY INSTALLATION INSTRUCTIONS Remove mounting tab on right side of relay box backing plate Remove ECU electrical box 4 bolts from hull Disconnect Slant Detection Switch Remove electrical system relay box 2 bolts from electrical box Install relay box backing plate onto electrical box backing with one original bolt Push relay box backing plate towards bolt check to make sure it s level and then secure Locate and drill 1 4 hole through electrical box backing Remove electrical box backing plate from hull and set plate aside Remove relay box backing plate from electrical box Word doc Part RY11841 ECU HFPWC H1 11 15 12 5 Replace relay box backing plate onto relay box using only 5 original bolts NOTE Apply blue Loctite to threads Do not over tighten bolts Do not use Replace relay box onto electrical box backing plate using one original bolt At opposite side use supplied M6 bolt washer and spacer to secure relay box to electrical box NOTE Apply blue Loctite to threads Do not over tighten bolts Place supplied spacer between relay box and electrical box and washer securing relay box to electrical Word doc Part RY11841 ECU HFPWC H1 11 15 12 Replace electrical box backing plate 4 bolts onto hull NOTE Apply blue Loctite to threads Do not over tighten bolts Install RIVA Athena ECU on2. if removed Oo E o Reconnect battery cables NOTE Positive red first Negative black second NOTE ECU is equipped with our Stage 3 Base Map Verify required parts to run this map safely or download others by going to www rivaracing com Athena click on Yamaha and then Base Maps in the left navigation Check bilge for tools rags etc Run craft on a flush kit to check for proper operation IMPORTANT The following documents in order are provided on the RIVA Athena ECU Manager Web Site Please go to www rivaracing com Athena gt Yamaha gt Downloads to obtain the following files 1 PC Software Maya Install before proceeding 2 Installing Maya PDF file outlining Maya installation process 3 Using Maya PDF file outlining how to use Maya 4 Connecting to ECU PDF file outlining how to connect Maya PC to ECU Remember the water belongs to everyone Please ride responsibly and respect the environment Technical Support For answers to questions regarding installation or trouble shooting RIVA Performance Products contact RIVA Technical Support directly at 954 247 0705 or by e mail at tech _support rivamotorsports com Limited Warranty RIVA Athena Pro Series ECU s carry a 1 year limited warranty to the original purchaser They are warranted to be free of defects in materials and workmanship under normal use and service Customer modified components will be void of
3. warranty This warranty is limited to defects in the primary components only Finish and or wear marks in or on primary components are not covered under this warranty RIVA Racing s liability is expressly limited to the repair or replacement of the components contained within or associated with this kit RIVA Racing agrees to repair or at RIVA s option replace any defective unit without charge if product is returned to RIVA Racing freight prepaid within the warranty period Any equipment returned which in RIVA s opinion has been subjected to misuse abuse overheating or accident shall not be covered by this warranty RIVA Racing shall have no liability for special incidental or consequential damages or injury to persons or property from any cause arising from the sale installation or use of this product No other warranty express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose applies Various states do not allow for the limitation of incidental or consequential damages and therefore the above exclusion or limitation may not apply to you Warranty does not include the expenses related to freight or transportation of parts or compensation for any inconvenience or loss of use while being repaired A copy of the original invoice and a Return Authorization Number RA must accompany all warranty claims Warranted replacement parts will be returned freight collect Word doc
4. F file outlining how to use Maya 4 Connecting to ECU PDF file outlining how to connect Maya PC to ECU Remember the water belongs to everyone Please ride responsibly and respect the environment Technical Support For answers to questions regarding installation or trouble shooting RIVA Performance Products contact RIVA Technical Support directly at 954 247 0705 or by e mail at tech _support rivamotorsports com Limited Warranty RIVA Athena Pro Series ECU s carry a 1 year limited warranty to the original purchaser They are warranted to be free of defects in materials and workmanship under normal use and service Customer modified components will be void of warranty This warranty is limited to defects in the primary components only Finish and or wear marks in or on primary components are not covered under this warranty RIVA Racing s liability is expressly limited to the repair or replacement of the components contained within or associated with this kit RIVA Racing agrees to repair or at RIVA s option replace any defective unit without charge if product is returned to RIVA Racing freight prepaid within the warranty period Any equipment returned which in RIVA s opinion has been subjected to misuse abuse overheating or accident shall not be covered by this warranty RIVA Racing shall have no liability for special incidental or consequential damages or injury to persons or property from any cause arising from the sale inst
5. SR PERFORMANCE EA amp MNES Pro Series ECU PART RY11841 ECU HFPWC APPLICATION S Yamaha 1 8L Engine Models GHO HO RIVA Athena ECU Manager Web Site www rivaracing com Athena In order to achieve optimal performance gains you will need to install the following RIVA Performance Products Products RIVA Power Filter OEM Intercooler Upgrade Kit SHO models RIVA Supercharger Impeller SHO models RIVA Fuel Pressure Regulator Kit RIVA Intake Manifold Upgrade Kit RIVA Engine Cooling Upgrade Kit RIVA Power Cooler Kit SHO models R Series Pump Impeller Required to provide safe operating parameters for all levels of modification including stock Along with the above components we recommend many others that will complement the RIVA Athena ECU providing improved performance in acceleration handling and top speed Please visit www rivaracing com kits to review the complete list Required tools Part Cut off Wheel or Small Saw N A Recommended tools Part Service Manual Please Call Word doc Part RY11841 ECU HFPWC H1 11 15 12 1 INSTALLATION INSTRUCTIONS Remove seats and rear storage bin Disconnect battery cables NOTE Negative black first Positive red second Remove rear grab handle seat support if equipped Remove electrical box cover 2 locking tabs at top Remove only the upper most warning sticker on electrical box cover Clean area with a non residual cleaner Pla
6. ace Power Connector into cradle on electrical box cover Use Power Connector to attach Dual Lock to electrical box cover At lower right side of electrical box loosen zip securing wiring harness to electrical box Extend wiring harness towards left side of electrical box At lower right side of electrical box tighten zip tie securing wiring harness to electrical box Inside front storage compartment remove rivets 5 securing service lid in place NOTE Press pin at center inward Connect Power Connector to ECU NOTE Do not force connector into ECU Once inserted use locking arm to complete connection and secure Remove service lid and locate remote control sensor OPEN UNLOCKED CLOSED LOCKED _ 7 Oo ee ll _ _ O _ _ a _ _ _ _ tll _ o a m a a o _ _ _ Word doc Part RY11841 ECU HFPWC H1 11 15 12 Disconnect electrical connector and install supplied block off into wiring harness connector NOTE Make sure block off snaps into place NOTE If a RIVA Vi PEC ECU was previously installed you must swap the black block off with the supplied blue block off Secure bypass module to OEM wiring harness using supplied zip tie ers Replace service lid and secure using stock rivets AANO i A i P e Replace rear grab handle seat support
7. allation or use of this product No other warranty express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose applies Various states do not allow for the limitation of incidental or consequential damages and therefore the above exclusion or limitation may not apply to you Warranty does not include the expenses related to freight or transportation of parts or compensation for any inconvenience or loss of use while being repaired A copy of the original invoice and a Return Authorization Number RA must accompany all warranty claims Warranted replacement parts will be returned freight collect Word doc Part RY11841 ECU HFPWC H1 11 15 12 8
8. ce Power Connector cradle at edge of raised area Install supplied stainless steel cradle onto outside of electrical box cover just below remaining warning sticker Secure using supplied hardware NOTE Install bolts 2 from inside and nuts on outside of electrical box cover Do not over tighten Word doc Part RY11841 ECU HFPWC H1 11 15 12 Cut a slot in the electrical box cover using a cut off wheel or small saw NOTE Sand edges so they are smooth Remove material on angled section Approx 5 long X 1 3 4 wide Disconnect stock ECU 3 electrical connectors at bottom NOTE Document order of connectors Remove stock ECU 4 bolts Retain stock hardware 2010 08 FX SHO models only Proceed to page 5 and follow steps through completion of installation All other Yamaha 1 8L models proceed to page 3 Install RIVA Athena ECU into electrical box and secure Place Power Connector box on top of exhaust pipe using stock bolts 4 NOTE Apply blue Loctite to Extend stock ECU connectors 3 towards motor bolts Do not over tighten Replace electrical box cover Carefully slide into place so that wiring harnesses fit into cut out Secure electrical box cover 2 locking tabs at top Connect stock ECU connectors 3 to Power Connector NOTE Do not force Verify order location Listen feel for click when locked in place On back of Power Connector remove adhesive backing on Dual Lock Carefully pl
9. nto cradle on electrical box cover Use Power Connector to attach Dual Lock to electrical box cover _ _ ee O _ _ _ _ _ __ ae _ _ _ _ _ _ _ p5 Word doc Part RY11841 ECU HFPWC H1 11 15 12 Disconnect electrical connector and install supplied Replace service lid and secure using stock rivets block off into wiring harness connector NOTE Make sure block off snaps into place Replace rear grab handle seat support if removed Reconnect battery cables NOTE Positive red first Negative black second tensa NOTE ECU is equipped with our Stage 3 Base Map y gt NANN i i j De Verify required parts to run this map safely or download E others by going to www rivaracing com Athena click on Yamaha and then Base Maps in the left navigation Check bilge for tools rags etc Run craft on a flush kit to check for proper operation Secure bypass module to OEM wiring harness using supplied zip tie IMPORTANT The following documents in order are provided on the RIVA Athena ECU Manager Web Site Please go to www rivaracing com Athena gt Yamaha gt Downloads to obtain the following files 1 PC Software Maya Install before proceeding 2 Installing Maya PDF file outlining Maya installation process 3 Using Maya PD
10. to electrical box and secure using stock bolts 4 NOTE Apply blue Loctite to bolts Do not over tighten At lower right side of electrical box loosen zip securing wiring harness to electrical box Extend wiring harness towards left side of electrical box Connect Power Connector to ECU NOTE Do not At lower right side of electrical box loosen zip securing force connector into ECU Once inserted use wiring harness to electrical box Extend wiring harness locking arm to complete connection and secure towards left side of electrical box OPEN UNLOCKED CLOSED LOCKED Place Power Connector box on top of exhaust pipe Extend stock ECU connectors 3 towards motor IMPORTANT NOTE If a RIVA Vi PEC V88 ECU was Replace electrical box cover Carefully slide into place previously installed remove the cable splicer installed so that wiring harnesses fit into cut out inline with black amp white wires at lower right side of electrical box and reconnect OEM wires directly Secure electrical box cover 2 locking tabs at top Connect stock ECU connectors 3 to Power Connector NOTE Do not force Verify order location Inside front storage compartment remove rivets 5 Listen feel for click when locked in place securing service lid in place NOTE Press pin at center inward Remove service lid and locate remote control sensor On back of Power Connector remove adhesive backing on Dual Lock Carefully place Power Connector i
Download Pdf Manuals
Related Search