forward control installation
Contents
1. AT THE SOLE DISC RETION OF THE MOTORCYCLES OWNER SUPREME LEGENDS USA HOLDS NO RESPONSIBILITY FOR MODIACATIONS TO YOUR MOTORCYCLE AND ORITS PERFORMANCE OR WARRANTY DUE TO THE INSTALLATION OF OUR PRODUCTS YOU UNDERSTAND AND AGREE THAT WE MAKE NO REPRESENTATIONS OR WARRANTIES OF ANY KIND EXPRESSED OR IMPLIED AS TO ANY MATIER WHATSOEVER INCLUDING THE CONDITION OF THE PRODUCTOR ANY COMPONENT PARTS THEREOF ITS MERC HANTABILITY OR ITS FATNESS FOR ANY PARTIC ULAR PURPOSE EXC EPT AS OTHERWISE PROVIDED HEREIN WE SHALL NOT BE LIABLE FOR DAMAGES INCLUDING SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER IN CONTACTOR IN TORTARISING OUTOF ORIN CONNECTION WITH THE PERFROMANCE OF ANY PRODUCT OR ANY COMPONENT PART THEREOF IN ITS USE BY YOU AND SHALL NOT BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF ORIN CONNECTION WTH YOUR USE OF THE PRODUCT INDEMNITY amp RELEASE a You understand and agree that many factors beyond our control affect the operational safety of the product including but not limited to the installation of the product according to the instructions provided with the product b You also understand and agree that the installation of the product may involve the use of tools equipment and construction methods which may present safety hazards which are beyond our control c Except as otherwise proved herein you will protect indemnify save harmless and release us our authonzed agents employees off2. ID 005 thick shim 2 5 8 ID Buna O rings 1 Stainless Brake Arm Cap Nut 1 1 OD x 06 thick shim 1 5 8 ID x 02 thick shim Sov eS WN All parts shown in hardware kit will be used in installation process Other hardware included with kit will be installed onto components during assembly at Supreme Legends USA INSTALLATION Important Installation Notes Please read entire instruction booklet pnor to installation This will fa milia rize you with the tools required to install this product and how the included items fit and operate Before attempting installation of this kit make sure to check package to be sure you have received all the necessary itemsincluded with this product and that the kit isthe correct unit for your motorcycle We recommend that you obtain your bike s factory service manual for detailed instructions on the re moval of stock parts necessary forthe installation of this kit Preparation Position motorcycle ona quality motorcycle lift with a weight rating greater than the weight of your motorcy cle Make sure motorcycle issecurely positioned and locked down before attempting any work Raise motor cycle to a comfortable postion for installation procedure You understand and agree that the product is designed to be installed and used asdescnbed in the assem bly instructions You agree not to make any modifications to the product and agree not to use any parts components oraccesso
3. which isapproximately 10 degrees down from the stock position and likely most comfortable for most nders Position 3 is 20 degrees down from stock and recommended for nders with longer insea ms Positioning youram Place your positioning bolt into the appropnate location asneeded This bolt will only fully install into one position and will match up to it s hole only when rotated propeny Once your desired position is attained apply any thread locker and tighten all 3 bolts securely beginning with positioning bolt and then bolts in slots Position 1 in the top left hole Position 2 in the lower left hole location RECOMMENDED Position 3 in the top nght hole position Pos 1 Pos 3 Step 5 Once you have located your prefered position for your brake am place a new o nng overthe bushing on both the back and front side of the assembly At this point we recommend putting a light layerof grease on your brake shaft pnorto step 6 Step 6 Slide your new brake am into position over the brake shaft being sure to push outer o ring back into place should it be pushed out While you are placing the am into position be certain to slip it into position at the master cylinder plunger pushrod Once this position is located slide your stock pin into position to secure the installation You may place cotter pin into the retaining pin at this point but we do not recommend bending legs out yet this should be d
4. URES YOU SHOULD HAVE THE PRODUCT AND OR ACCESSORIES INSTALLED BY A PROFESSIONAL MECHANIC SUPREME LIMITED WARRANTY Supreme Legends USA offers a limited 18 month non transferable warranty from the date of purchase to the onginal purchaser on all parts included with this kit to be free of manufacturing defects in matenals and workmanship excluding nomal wear and tear If the condition of an item requires warranty service please contact Supreme Legends USA immediately The limited warranty is applicable only if the instructions are followed and the products are used propery Supreme Legends USA will determine if it isnecessary to retum an item for evaluation and validity of warranty claim If an article isfound to be defective upon inspection by Supreme Legends USA we will repairor replace the defective article at our discretion without charge The customer will pay freight to Supreme Legends USA and we will pay any applicable retum freight A Retum Merchandise Authorization RMA fom provided by a customer service representative must be included will all retumed product along with a copy of the onginal receipt All items must be packaged in such a fashion asto eliminate any further damage Unauthorized retums will not be accepted SUPREME LIMITED WARRANTY continued Normal wear and tear of Supreme Legends USA products or damage resulting from misuse accidents improper installation alterations or abuse including tampering ordamage in
5. icers directors and shareholders from and against all liabilities obligations claims damages penalties causes of action costs and expenses imposed upon or Incurred by or asserted against us and our authonzed agents employees officers directors and Shareholders or any of our assignees by you or any third party by reason of any assembly use maintenance possession or operation of the product any loss damage or destruction of the product as of and after delivery and any other act or event relating to or caused by the product including but not limited to consequential or special damages or any kind or any failure on your part to perform or comply with any of the terms and conditions hereof or any and all liability for property los or damage or any and all damages resulting from death or personal injures including loss of services which any person may sustain on account of ansing out of or in connection with any use maintenance possession or operation of the product In the event that any action suit or proceeding is brought against us or any of our authonzed agents employees officers directors or shareholders by reason of any such occurence you will upon request and at your expense resist and defend such action suit or proceeding or cause the same to be resisted and defended by counsel designated and approved by US INSTALLATION KIT INCLUDES 1 025 thick wavy spring washer 1 Serrated Belleville washer 1 1 2
6. ll Bagger Ill Bagger Adjustable FLH FLT Ams Installation Instruc tons ARAN Thank you fora choosing a Supreme Legends USA product Supreme Legends Adjustable Extended BaggerAmsare designed to give your FLH FLT more foot oom on your floorboards while offering adjustable positions on both the brake and shift sides The lower amp extended brake ams offer easier braking with less pressure required foractuation We hope that you will be pleased with your purchase Should you have any questions please contact ourcustomer service department at 714 504 0715 or visit us onthe web at www supremelegendsusa com IMPORTANT WARNING ITIS CRITICAL THATALL SUPREME LEG ENDS USA PRODUCTS AND ACCESSORIES BE PROPERLY AND SEC URELY ATIACHED TO YOUR VEHICLE IMPROPER ATIAC HMENT COULD RESULT IN A MOTORCYCLE ACCIDENT AND COULD CAUSE SERIOUS BODILY INJ URY OR DEATH TO YOU OR OTHERS YOU ARE RESPONSIBLE FOR SEC URING THE PRODUCTS AND OR ACCESSORIES TO YOUR MOTORCYCLE CHECKING THE PRODUCTS AND OR ACCESSORIES PRIOR TO USE AND PERIODICALLY INSPECTING THE PRODUCTS AND OR ACCESSORIES FOR ADJ USIMENT WEAR AND DAMAGE THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUC TIONS NOTES AND WARNINGS SUPPLIED WITH YOUR SUPREME LEGENDS USA PRODUCTS AND OR ACCESSORIES PRIOR TO INSTALLATION OR USE IF YOU DO NOTUNDERSIAND ALL OF THE INSTRUCTIONS NOTES AND WARNINGS OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WTH THE INSTALLATION PROCED
7. nes in connection with the installation and the use of the product that are not authonzed and approved by us Installation Steps Installing the Shift Ann s KPLEA SE NOTE These instructions are for both the Il Gill Bagger Senes and will vary only slightly Step 1 Remove your existing control components including any ams and any end capsor spacers Remove rear shift linkage from shift rod There isno need to adjust the shift rod from it s existing position asall adjustments can be made on the outside armsdunng the last steps of installation Step 2 Once all existing components are removed from the shift shaft place the 5 8 ID shim at the back side of the shift shaft We recommend putting a light coat of silicone grease on the shim face once it isin place If installing a Ill Bagger senes you will replace your stock shift shaft with the new one pnorto doing this Step 3 Remove bolt completely from rear new rear shift linkage Slide over splines and completely against the shim Using thread locker blue isacceptable replace bolt into hole line up into shaft s retaining groove and thread down into bottom half Tighten securely There isno need to over torque this bolt Step 4 Reconnect shift rod to rear shift linkage being sure to use thread locker if necessary Step 5 Once step 4iscomplete place the wavy spring washer into the shift spacer recess shown below and place that end onto the outboard side of the shif
8. one afterall adjustments and comfort checks have been performed Step 7 Insert Belleville washer into brake arm nut as shown This willact asa secondary lock to yourthread locker Place 1 diameter shim over shaft against o ring on brake arm then place brake am nut onto shaft Snug this nut down do not tighten completely At this point we recommend bringing your bike down off the lift Sit on the bike to make sure that you are ata comfortable position for braking Please note thisisa modified adjustment and a longeram so you will require time to acclimate to the new position Step 8 If you are content with your final postion remove brake am nut apply thread locker we recommend red here and tighten nut back up completely being sure to still allow freee movement of brake am At this point you should bend the legs of the cotter pin In the retaining pin Step 9 Reinstall floorboards being sure to use thread locking compound where necessary Step 10 Enjoy your new Supreme II III Baggers
9. t shaft pushing it up to the primary casing This washer is meant to retain the soacerin place while still allowing free movement of shift arms On the outboard side of the installed spacer place the 1 2 ID shim We recommending greasing this shim and the face of the spacer with a light slicone grease for easy shifting Step 6 Remove bolt from bottom of shift arm s and apply thread locker to threads Reinstall bolt but do not tighten yet Place shift arm into approximate desired position on splined shaft Being sure to hold the rear shift link at the same time squeeze the armstowardseach other and tighten the bolt on the shift arm snugly If you are installing a Il Bagger control this shifter will be used for all shifting and should be adjusted to enable comfortable up and down shifting If you are installing a llil Bagger seres adjust each am forheel and toe shifting as necessary before tightening anything down On heel toe shifters the toe shifter will sit Slightly in front of the board while the heel shift will sit just above the rearof your board to ensure consistent shifting Once all adjustments are made tighten completely Shift Spacer with spring washer Installing the Brake Am Step 1 Begin by removing your brake side floorboard This will allow easy accessto parts during removal and installation Step 2 Remove the nut from your stock brake arm Remove any shims and o nngsaswell Step 3 Locate the pin
10. transit are not covered by this Limited Warranty The purchaser acknowledges that Supreme Legends USA has no control over the attachment of its products to motorcycles and or motor vehicles or the attachment of items to Supreme Legends USA products Accordingly Supreme Legends USA cannot assume responsibility for any damage to property ansing out of improper attachment or use of its products In addition this Limited Warranty applies only to Supreme Legends USA products and not to other products used in conjunction with Supreme Legends USA products This imited Wa manty is in lieu of all other warranties expressed orimplied and doesnot cover consequential damagesof any kind that may anse from the use or misuse of any Supreme Legends USA product FOREVER SUPREME We know how hard people try to keep their motorcycles looking new but all parts will wear over time We developed this program to show our customers that we care And if you were ourcustomer once you are entitled to be our customer for life If you have an old registered Supreme Legends USA part you can trade it in and receive the following discountsona new part of equal or lesser value Second Year 15 off Third Year amp Beyond 10 off DISC LAIMER THE INSTALLATION OF SUPREME LEGENDS USA PRODUCTS MAY ADVERSERLY AFFECTOR VOID YOUR MOTORCYCLES FACTORY WARRANTY WE ARE NOT RESPONSIBLE FOR ANY ISSUES RELATED TO YOUR MOTORCYCLES FACTORY WARRANTY OUR PRODUCTS ARE DESIGNED TO BE INSTALLED
11. which holds your existing brake am to the mastercylinder plunger You will need to remove the cotter pin which retains it from the backside This may take a moment or two If you have additional cotter pins it is sometimes easier to simply snip the bottom legsof the pin and remove the head rather than fight a losing battle with a stubbom pin Once the cotter pin is out remove the main pin and then the brake am the plunger will move enough to allow you to push it up out of the way Remove any remaining o rings from the brake shaft You may leave any shims on which may be atthe back ofthe shaftas they should not affect final fitment Step 4 Before installing the brake am you will need to select your desired position of adjustment To select your mounting postion you will loosen the two bolts within the slots to allow the brake link to rotate to your position Please note these two bolts and your positioning bolt have a serrated Belleville washer installed to insure non slippage in their final position We still recommend also applying a thread locker to the bolts before final installation Please take note Brake armsare located at position 2 when shipped from Supreme They are NOTtightened but are left snug so that you may make any final adjustments Due to the contours and extension of these ams position 1 may only be used on modified exhausts and will likely not fit with your stock exhaust We recommend beginning at position 2
Download Pdf Manuals
Related Search