CRANEX® Novus e Installation and Set-up Manual
Contents
1. 52 Installation Commands Still Mode Image Calibration l CRANEX Novus e However if the dental imaging software prompts an error message Please calibrate the device on startup perform CCD re calibration as instructed below 1 PC Prepare the unit for an exposure 2 Touch the service button on the main control panel of the unit to open the configuration win dow 3 Select Installation Commands 4 The personal identification number PIN screen will appear Key in 1204 and touch the OK key Then select Image Calibration 5 Remove the chin rest and make sure that there is nothing between the sensor and tube head Installation and set up manual 208668 CRANEX Novus e 5 Aligning the unit 6 Protect yourself from radiation and take an exposure 7 PC Use the dental imaging software to exam ine the image It should be evenly grey all over with no granularity nor horizontal lines stripes If the image is not evenly gray repeat the calibration until it is If artefacts appear on the image make sure that there is nothing between the sensor and the tubehead 8 Touch the Arrow button to exit Image Calibra tion Installation and set up manual 208668 932. Lift the top of the column and slide the packing piece that supported it underneath so that you can access the underside of the column Attach the two connecting rods to the two screws at the top rear of the column Attach the wall bracket to the connecting rods with the washers and nuts 3 2 Attaching the unit to the wall 1 CAUTION HEAVY OBJECT A minimum of two persons are required for the following task Transport the unit to the place where it is to be installed NOTE The transportation wheels optional are at tached to the base of the column with two M10 screws and can be used to wheel the unit to the place where it is to be used 2 Mark the position of the two fixing holes on the wall according to the dimensions given in the section 2 6 Fixing hole dimensions Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit Alternatively lift the unit into the position where it is to be used and then using the wall bar as a template mark the positions where the holes must be drilled Hold a spirit level on the side of the column and then on the front to help to position the unit so that it is as vertical as pos sible Drill two holes with diameters suitable for the 10 mm 3 8 in fixing hardware being used and then attach the unit to the wall with the ap propriate fixing hardware Do not fully tighten the screws yet Remove the packaging material that protects the rota
3. Service key Test exposure key Unit status indicator 7IQNMO 4 Installation and set up manual 208668 CRANEX Novus e 1 Introduction 1 5 Disposal of the transportation packaging The unit is transported in a corrugated cardboard box that is attached to a wooden pallet Inside the box preformed expanded polystyrene packaging material protects the unit from shock and damage Packaging material Weight kg Ib Cardboard box and lid 21 0 46 3 Wooden pallet 74 16 3 Expanded polystyrene 7 6 16 8 Total weigh 36 0 79 4 When disposing of the transportation packaging materials make sure that you follow all local na tional and international regulations regarding the correct and safe disposal and or recycling of these materials some transportation packaging materials may be non environmentally friendly These transportation packaging materials must be disposed of in ac cordance with all local national and international regulations regarding the disposal of non environ mentally friendly materials NOTE It is advisable to keep some transportation pack aging so that units can be repacked and easily and safely moved to new locations if required Installation and set up manual 208668 5 2 Pre installation requirements CRANEX Novus e 2 Pre installation requirements 2 1 The Unit The unit is supplied in one box on a pallet The dimensions of the box with pallet are Length Width Height 191 cm 85 cm 103 cm
4. at the bottom rear of the column and then place the exposure switch on the expo sure switch holder Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit 3 4 Connecting the unit to the power supply The unit must be connected to its own dedicated power supply 100 to 120 VAC or 220 to 240 VAC No other equipment should be connected to the same power supply Extension cables MUST NOT be used to connect the unit to the power supply 1 The power supply must be equipped with cir cuit breaker 2 Connect one end of the power lead to the back of the unit and the other end to the power sup ply Observe any national and local electrical re quirements with regards the connection of dental x ray equipment to a power supply Installation and set up manual 208668 21 3 Installing the unit 3 5 Preparing the PC CRANEX Novus e NOTE The PC and any other external device s con nected to the system must meet the IEC 60950 standard minimum requirements Devices that do not meet the IEC 60950 standard must not be con nected to the system as they may pose a threat to operational safety Ae 22 Position the PC to be used with the unit at least 1 85 m 73 in away from the unit Make sure that the patient cannot touch the PC while being x rayed NOTE If the PC to which the unit is to be connected is to be part of a larger system make sure that all the other system components and devic
5. been keyed in the OK tick button will become active Touch the OK tick button to accept the change and return to the main display Touch Arrow button to discard the change and return to the main display PC SCANORA In the Tools Cranex Novus e setup window select the Settings page DfW In the Options Cranex Novus e Setup window select the Settings page In the Device Connection section click the IP based radio button to select it Then click the Enable changing IP address check box to activate the IP address field PC Key in the new IP address into the IP address field Device IP address v Enable changing IP address 194 9 227 253 Send to Device 7 PC Click the OK button to close the settings window The Ready indicator will turn green Installation and set up manual 208668 33 3 Installing the unit 34 Multi connect Mult Connect Y Use Mult Connect Workstation identifier CRANEX Novus e Multi connect allows the unit to be used by several PCs within a network APC must reserve the unit before it can be used 1 PC SCANORA In the Tools Cranex Novus e Setup window select the Settings page DfW In the Options Cranex Novus e Setup window select the Settings page PC Click the Use Multi Connect check box to select it and then from the drop down list se lect a unique Workstation identifier number between 1 and 8 for the PC being configured Additional wo
6. indicates that the bitewing program has been installed at the factory Order the bitewing License Key from SORE DEX Customer Service The order code is 900669 Bitewing Program Upgrade When ordering you need to give the Serial Number of the unit in which the bitewing pro gram will be activated SOREDEX Customer Service will e mail the license key to you Switch on the unit and touch the service button to enter the service mode Click the Bitewing Activation button A keypad will appear which allows you to enter the license code Enter the activation code press OK tick and the bitewing program will be activated Press the Back button twice to return to the main menu Restart the unit to activate the bitewing pro gram Installation and set up manual 208668 CRANEX Novuse_ 4 Checking the alignment and finishing the installation 4 Checking the alignment and finishing the installation 4 1 Checking the alignment of the CCD Sensor 1 PC Prepare the unit for an exposure NOTE If the dental imaging software prompts an er ror message Please calibrate the device on startup perform CCD re calibration as de scribed in section 5 4 2 Remove the chin rest Touch the service button on the main control a panel of the unit to open the configuration win dow Status ready 4 Select Installation Commands Installation Commands 5 The PIN number screen will appear This is a security feature to prev
7. remove the base plate or loosen the position nuts that attach it to the unit AA lt re Holding screws 5 16 Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit 10 Rotate the guide pin assembly and insert it into the hole in the base plate Note that the plain section of the guide pin must be downwards and the nut on top A a Plain section gt downwards N IMPORTANT NOTE If the guide pin does not fully enter the hole in the base plate the top of bearing is NOT level with the top of the base plate the rotating unit must be moved slightly To do this remove the transportation screws and packing pieces see step 12 and then slide the rotating unit gen tly backwards or forwards until the guide pin drops into place Installation and set up manual 208668 17 3 Installing the unit CRANEX Novus e 11 Secure the guide pin in position with the two holding screws AAi i AA ie bey PA VA A T ee yr gt Fe yor ve AA E ee r yj Rite FA M gt 2 bine Mala wry wots ett ERs l Ap y WV SIAN 7 oe ie A Fy sa or A y5 ee Soy ty Soe a f P EP 4 ider ya amp oa J We ae fe ae GA oe he nolaing screws 12 Remove the four 4 transportation screws painted RED and four 4 packing pieces that hold the rotating unit to the upper shelf Now rotate the rotating unit to the
8. side profile left assembly 4 screws CAUTION Be careful not to damage the flat cables that attach the exposure warning light and control panel to the unit behind mirror 50 5 screws Remove the mirror assembly It is held in place with 6 screws located behind the mirror Both the midsagittal and frankfort lights have similar adjusting mechanisms Loosen the clamping screw on the light module and rotate the light to position beam vertically For left right beam movements loosen the nuts screws that hold the light module bracket in position and adjust the laser lights accordingly Left right adjustment BY 7 i H Rotation adjustment Installation and set up manual 208668 CRANEX Novus e 5 Aligning the unit Focal trough 1 Loosen the five 5 screws that hold the sen sor inner cover in place and then remove the cover 2 Loosen the clamping screw on the light mod ule and then rotate the light to position beam vertically To adjust the beam in the up down left right directions loosen the nuts screws that hold the light module bracket in position and adjust the laser lights accordingly Mee Lote left right adjustment rotation adjustment Installation and set up manual 208668 51 5 Aligning the unit 5 4 Calibrating the CCD sensor NOTE The CCD sensor is calibrated at the fac tory and thus does not normally need to be cali brated again Status ready
9. the location where the unit is to be installed 2 Remove the straps that hold the box to the pal let 3 Lift off the top of the box and then the sides 12 Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit Remove all the accessories the accessory box and as much packaging material as pos sible NOTE DO NOT remove the packaging material that protects the upper shelf and the rotating unit Fold down the end of the box that is nearest the hinged section part of the column and then slide the unit over the edge of the pallet so that you can access the underside of the hinged section of the column Support the hinged column section before loosening the screws that hold it to prevent it falling and causing damage or injury Loosen the screws the securing nuts are inside the column on the sides of the column that hold the hinged column section in the ver tical position Turn the hinged column section down so that it is horizontal Secure it in posi tion with the two screws supplied M10 x 16 the fixing holes are on the underside rear of the column Tighten the two screws M10 x 16 on the sides of the column Installation and set up manual 208668 13 3 Installing the unit 14 CRANEX Novus e IMPORTANT NOTE If the unit is to be attached to the show stand pt no 9802666 refer to the sepa rate installation instructions supplied with the show stand
10. 2 Switch the Unit on 3 PC Start the PC and then open the dental imaging software that you installed 4 PC SCANORA In the Tools Cranex Novus e Setup window select the Settings page DfW In the Options Cranex Novus e Setup window select the Settings page Novus e Setup Device Settings Driver Info IP based Device IP address v Enable changing IP address In the Device Connection section click the IP based radio button to select it Then click the Enable changing IP address check box to activate the IP address field 28 Installation and set up manual 208668 CRANEX Novus e sN Novus SOyyxxxx Fw 1 00 Core 36 Graphics 1 IP Settings Installation Commands Bitewing Activation 3 Installing the unit Touch the service button on the main control panel of the unit IMPORTANT NOTE The unit can have any IP address but the unit and PC must always be in the same sub net The subnet mask of the unit is fixed to 255 255 255 0 NOTE With the network configuration the default IP address of the unit must be changed to the IP address obtained from your local IP adminis trator With standalone configuration you can avoid changing the IP address of the unit by setting the IP address of the PC to the same sub net as the default value of the unit After changing the PC IP address in this way proceed to step 11 to finish the configuration The configuration screen will appear on the dis
11. 76 in 34 in 41 in The assembled unit weighs 120 kg 265 Ib Make sure that the floor where the unit is to be installed can support this weight The unit must be permanently attached to the wall or if this is not possible to the show stand If the unit is to be permanently attached to a wall make sure that the fixing hardware to be used to attach the unit to the wall and the wall itself can withstand a continuous pull out force of at least 300 kg 660 Ib The fixing hardware NOT SUPPLIED to be used to permanently attach the unit to the wall must be the correct type for the wall material The diameter of the fixing hardware MUST be 10 mm 3 8 in DO NOT use smaller diameter fixing hardware If the wall is made of thin material you may have to use a reinforcing plate on the rear side of the wall to hold the fixing hardware If the wall is not strong enough to support the unit or if you are not sure if the wall will support the unit use the show stand Installation and set up manual 208668 CRANEX Novus e 2 Pre installation requirements If the area where the unit is to be installed is subject to earthquakes and the unit is to be permanently attached to the wall then the base of the column must be permanently at tached to the floor The fixing hardware NOT SUPPLIED to be used must be the correct type for the floor and floor material The di ameter of the fixing hardware MUST be 8 mm 5 16 in The place where
12. ENGLISH CRANEX Novus e Installation and Set up Manual 208668 rev 2 2012 10 CRANEX Novus e Installation and Set up Manual CE 0537 Medical Device Directive 93 42 EEC CRANEX Novus e Installation and Set up Manual Number 208668 Ver 2 2012 10 Original approved English language version Manufactured by SOREDEX PaloDEx Group Oy Nahkelantie 160 Tuusula P O BOX 148 FI 04301 Tuusula Finland Tel 358 0 10 270 2000 Fax 358 9 701 5261 SOREDEX CRANEX DIGORA SCANORA are registered trade marks of SOREDEX SOREDEX endeavours to produce product documentation that is accurate and up to date However our policy of continual product development may result in changes to products that are not reflected in the product docu mentation Therefore this document should not be regarded as an infallible guide to current product specifications SOREDEX maintains the right to make changes and alterations without prior notice Installation and set up manual 208668 Contents T POGUE UO canina aa a 1 TAWADOUE TIS WMANUAl ascscscerabsdtertuaicsessasnastaacedec sasava dureeuo E 1 1 2 Associated documentation cece cece ecceecceeeceeeaeeeeeeteeeseeeeeesaeeseeseeesaeenes 1 1 3 WarningS And pPreCautions cccccccscccecceeeceecceecaeecueeceecaeeseeeeeesaseseeeses 2 D rnDO ASTANA OM iseesaiscraecsateradacnacacund nea paananuuseeeneiceinanenanedecaanmacnaaneeats 2 UFINGHUNIL OD
13. Patient in out position PIO Refer to the user s manual Packing pieces x 4 Transportation screws x 4 18 Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit NOTE If the unit ever has to be relocated replace the packing pieces transportation screws and the guide pin assembly step 9 BEFORE remov ing the unit from the wall or exhibition stand 13 Attach the covers to the bottom of the column Attach the Front Cover A to the front of the column with the special long screws 4 they are inserted from the rear Do not tighten them yet Special long screws x4 Attach the Side Covers B to the sides of the column Note that the front edge of the Side Covers is positioned between the column and the Front Cover The rear edge is attached to the back of the column with two screws Tighten all the screws Installation and set up manual 208668 19 3 Installing the unit 20 3 3 Exposure switch 1 x fi CRANEX Novus e Attach the exposure switch holder to the side of the unit using two 2 screws If the user does not want to have the exposure switch positioned on the unit attach the expo sure switch within the range of the spiral lead to where requested Make sure that the eposure switch is posi tioned so that the user can protect themself from radiation and can see the patient during an exposure Connect the exposure switch cable to the con nector
14. S FAL ON esecuri wai ner iraietatt add woken E 2 EL CMI ASS CMU ON sisireacactarnsseccana a EEA 3 MaN ANU Sic seaside r aint Ganaaan tea nd ooo 3 LIE COMMON Sinzencuiateesieiasve am muratacaarandacustonceeanecis aimee acne ecm scale E 4 1 5 Disposal of the transportation PACKAGING cccceccceeeseeseeteeeeeeeeeeeeeees 5 2 Pre installation requireMent ccccsccsececeeeeeeeeseeeeeeneoneenseeseesaes 6 Vis ep aloe 8 ig eee ee ne een ee ee ee ren ene mene wine eRe Nee etsy ence Teeny kee te ee 6 22 OPO Ree ee Ree EP eee ee Re EER cane eee eee eee 8 2 3 The dental imaging software 00 ccc cecceeceseeeceeeceeeeeeeeseeeeeeeseeeseeeeeeeaes 8 24A SPACE TEQUIFEIMMEING sarraa E A diovan tar atiaannees 8 ZOU AMENN S aasaran sia E A 9 26 FIXING MOLE GIMENSION S ron a a aae als 10 2 Fixing hardware and installation and Setup tools cccceceseeeeeeee ees 11 FNO VAG AC oi cs ok aed etn ch aes a te Mates 11 i Stalll AOR TOONS sea A 11 Calibration and setup tOOIS ccccecccecceecaeeeeeeeeeeceeeeneeeeeseeseeeeeeeeeenees 11 S MEDS CANIN Ahe UNa e eeereeee acess 12 3 1 Preparing the unit for installation ccc ccccecccceccceeeceeeeeeeeseeseeeeaeeseees 12 3 2 Attaching the unit to the wall ccc cecccecceeceeeeeeeeeeeeeeseeeeeeeaeeseeenes 14 DiS EXPOSE SWI Nea soaaaieris tisscticla tania snataarsaa wutaibene ce tata aden sar adennamenceaars 20 3 4 Connecting the unit to the power sup
15. _ 4 Checking the alignment and finishing the installation 4 3 Checking the positioning lights Midsagittal light 1 Attach the chinrest and a rod to the support holder Press the light button to switch the patient posi tioning lights on The light beam must be vertical and strike the center of the rod Correct Incorrect Incorrect If the beam is not in the correct position it must be adjusted See 5 3 Adjusting the positioning lights Installation and set up manual 208668 41 4 Checking the alignment and finishing the installation CRANEX Novus e Frankfort light 1 Draw a horizontal line on a sheet of paper parallel to one side Remove the chin rest and hold the piece of paper on the chin rest sup port 2 Press the light key The frankfort light must be parallel to the line on the piece of paper If the beam is not in the correct position it must be adjusted See 5 3 Adjusting the positioning lights Focal trough light 1 Attach the ball phantom to the support holder 2 Press the light button to switch the patient po sitioning lights on The light beam must strike the line that crosses the ball phantom Correct Incorrect If the beam is not in the correct position it must be adjusted See 5 3 Adjusting the positioning lights 42 Installation and set up manual 208668 CRANEX Novuse_ 4 Checking the alignment and finishing the installation 4 4 Completing the Installation Check that the unit functi
16. creen PC Click the OK button to close the settings window NOTE If the remote IP address setting fails use the MANUAL method See section Manually changing the IP address Installation and set up manual 208668 31 3 Installing the unit CRANEX Novus e Manually changing the IP address sN Novus SOyyxxxx Fw 1 00 Core 36 Graphics 1 IP Settings Installation Commands Bitewing Activation Choose IP Configuration Mode MANUAL REMOTE 32 The IP address of the unit can be changed manu ally NOTE Always set the IP address of the PC before chang ing the IP address of the unit 1 Touch the service button on the main control panel of the unit 2 The configuration screen will appear on the display It shows the unit serial number the firmware version numbers and several function buttons IP Settings Installation commands and optionally Bitewing Activation Select IP Settings NOTE See section 4 for information about Installa tion Commands and section 3 7 for informa tion about Bitewing Activation 3 The IP configuration modes will appear on the screen Manual or Remote Touch the Manual button Installation and set up manual 208668 CRANEX Novus e IP Address 194 9 227 253 1 2 A ae 7 8 IP based Status ready 3 Installing the unit The Manual IP address connection screen will appear Key in the new IP address When the new IP address has
17. crouse audesecvaseetuausgeectaedven eevee ieee 42 4 4 Completing the Installation cccccccccecccseeseeeceeeeceeeseeseesseeseneeaeeees 43 5 Aligning the unit cece eee cece eeeeeeeceeeeeeeeseeseesensansonsoneonsenenaes 44 SL AllOniInGg the CCL SENSOR s cccesaiecaee ate tices eeoie a eaehconat 44 5 2 Adjusting the image GQeOMEIry cccccecccseceeeceeeceeceeeseseceeeseeseeeseeeees 46 center Dall NOE FOUNG aeeoa a E amass 46 Distances between center ball and left and right balls not equal 47 5 3 Aligning the positioning lights ccccccccccceeceeee cesses eeeeeseeseeeeeaeeseeees 49 Midsagittal and frankfort sresccesciisi a 49 POCA AV OU OI eoe era amcateaaitiadtis vraag teat ealecone eee humntdeaedeioaammanaesteceeatenan 51 5 4 Calibrating the CCD sensor seiscasodrochantctecatesrcusnn ian hacniis essence ceueendeatoss 52 VI Installation and set up manual 208668 CRANEX Novus e 1 Introduction 1 Introduction 1 1 About this manual This manual explains how to install and set up the CRANEX Novus e digital panoramic dental x ray unit the unit You will need to operate the unit during the align ment and checking procedure Make sure that you know how to operate the unit before starting to install and set up the unit It is also essential that person installing and set ting up the unit should have attended the manu facturer s service training course 1 2 Associated documen
18. e network configuration you may need a new IP address for the unit from your local system administrator Network device Installation and set up manual 208668 23 3 Installing the unit CRANEX Novus e Connection methods The unit can be connected to the PC in two ways Direct connection or IP based connection Both of these connection methods allow the unit to be used in either Standalone or Network Configu ration Direct Connection Direct Connection is a connection method based on the unit serial number for establishing a con nection between the unit and the PC Direct connection is not based on IP protocol but instead utilizes a proprietary Ethernet protocol NOTE In some configurations the PC firewall or other network devices may prevent direct connection from operating Direct connection requires traffic to be allowed between the PC and unit through the network devices and the PC firewall in in bound outbound direction for Ethernet protocol ID Ox6000 If there are difficulties with the direct connection use the IP based connection method instead IP based connection IP based connection uses IP Protocol to estab lish a connection between the unit and the PC It requires the IP addresses of both the unit and the PC to be configured correctly IMPORTANT NOTE The default IP address of the unit is 194 9 227 251 and the subnet mask is fixed to 255 255 255 0 The unit offers two alternatives for configuring
19. ed 4 PC SCANORA In the Tools Cranex Novus e Setup window select the Settings page DfW In the Options Cranex Novus e Setup window select the Settings page Novus e Setup Device Settings Driver Info Device Connection Direct Connection Direct Connection settings Device serial number So0120719 Computer network connection Broadcom Netxtreme 5 xx Gigabit Controller Y In the Device Connection section click the Direct Connection radio button and then key in the complete device Serial Number of the unit it is on the type label into the Device se rial number field 26 Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit Select the correct Network Interface Card NIC from the Computer network connec tion drop down list NOTE If there is more than one NIC in the PC make sure that you select the one that is connected to the device Click OK to save the settings 5 The unit will automatically connect to the PC within 5 15 seconds Installation and set up manual 208668 2 3 Installing the unit CRANEX Novus e Connection using the IP based method 1 Standalone configuration Connect one end of the Ethernet cable to the unit the connector at the rear of the column and the other end to the PC Network configuration Connect one end of the Ethernet cable to the unit the connector at the rear of the column and the other end to the network
20. en the center ball and the left and right balls are DIFFERENT then the chin support CS must be must be adjusted 1 To adjust the chin support first remove the Chin Support Holder 1 screw accessible from the underside of the patient support handle 2 Loosen the set screw that holds the Lower Shelf Screw the horizontal screw in position and turn it to adjust the position of the Chin Support Holder Set screw Installation and set up manual 208668 47 5 Aligning the unit CRANEX Novus e If the right hand distance is greater that the left C move the chin rest to the left If the left hand distance is greater that the right D move the chin rest to the right CAUTION DO NOT loosen the screws 2 that attach the Chin Support Holder to the Patient Handle Move chin rest to left D Move chin rest to right 3 Take another ball pin exposure to confirm the unit is now correctly aligned Readjust if re quired 4 After the adjustment has been done retighten the set screw and replace the Chin Support Holder 48 Installation and set up manual 208668 CRANEX Novus e 5 Aligning the unit 5 3 Aligning the positioning lights Midsagittal and frankfort 1 Remove the corner piece it pulls off The midsagittal light can now be accessed and adjusted see step 5 Installation and set up manual 208668 49 5 Aligning the unit CRANEX Novus e To access the frankfort light remove the
21. ent the user from ac cidentally accessing the installation service Enter PIN Code commands AAAA Key in 1204 and touch the OK key Installation and set up manual 208668 37 4 Checking the alignment and finishing the installation CRANEX Novus e 6 The service function will appear on the screen Select Still Mode still Mode Image Calibration 7 Protect yourself from radiation Press and hold down the exposure switch to take an exposure 8 PC Use the dental imaging software to exam ine the image that appears E g If the CCD sensor is correctly positioned the image will show a vertical black line the beam in the middle of a vertical light gray area the CCD aperture Both the beam black line and the CCD aper ture light gray area must be vertical and the bottom edge of the beam black line must be Correct between 0 1 and 2 mm from the bottom edge of the image If the beam black line is not in the middle of the CCD aperture the gray area or the CCD aperture gray area is not vertical the CCD sensor must be adjusted See 5 1 Aligning the CCD sensor 9 Touch the Arrow button to exit the Still Mode and return to the main menu 38 Installation and set up manual 208668 CRANEX Novuse 4 Checking the alignment and finishing the installation 4 2 Checking the image geometry ball pin phantom test 1 PC Prepare the unit for an exposure 2 Replace the chin rest PAN 3 Setup the unit t
22. es are installed connected and configured correctly Refer to the documentation supplied with the other components and devices for information on how to do this Switch the PC on and install the dental imag ing software to be used with the device For information on how to do these refer to the installation configuration documentation supplied with the dental imaging software IMPORTANT NOTE During the installation when the Select Fea tures window appears make sure that you select the CRANEX Novus e option Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit 3 6 Connecting the unit to the PC The unit supports 10Base T 100Base TX Ethernet connections The PC must be connected to the unit in accord ance with IEC 60601 1 1 Connection options Standalone With the standalone configuration the unit is con nected to a PC and the unit then reserves the whole network interface card The unit and PC then function as a single standalone system with no access to other networks If it is necessary for the PC to be connected to another network the PC will require two network interface cards Network With the network configuration the unit is con nected to the PC via a network device With this configuration the PC is connected to the unit and to other networks with a single network card The unit is also accessible from other PC s in the same network same subnet For th
23. ion requirements 2 Fixing hardware and installation and setup tools Fixing hardware Installation tools The following tools and hardware are required to install and set up the unit NOTE THESE ARE NOT INCLUDED IN THE DELIVERY OF THE UNIT UNLESS OTHERWISE STATED WALL attachment requires two sets of 10 mm 3 8 in diameter fixing hardware WALL and FLOOR attachment requires two sets of 10 mm 3 8 in AND two sets of 8 mm 5 16 in diameter fixing hardware The type and length of hardware to be used will depend on the wall material and floor material to which the unit is to be attached IMPORTANT NOTE Fixing hardware is not required if the show stand is used Refer to the separate instructions supplied with the show stand Electric drill Spanners wrenches 7 10 17 two mm AF Hexagon socket wrenches Allen keys 1 5 8 mm Slot blade screwdrivers 0 5 x 3mm 0 6 x 3 5 Torx screwdrivers T20 125 T30 Spirit level Pliers and wire cutters Scissors Knife Transportation wheels pt no 200830 Optional not supplied with the unit Calibration and setup tools Ball pin alignment tool pt no 201916 Test tool line pair phantom for countries where this calibration tool is required pt no 6904430 Installation and set up manual 208668 11 3 Installing the unit CRANEX Novus e 3 Installing the unit 3 1 Preparing the unit for installation 1 Transport the boxed unit to
24. its IP address Remote and Manual With the Re mote alternative the unit receives its IP address from the PC With the Manual alternative the user sets the IP address of the unit using the Graphical User Interface GUI of the unit It is recommended that Remote alternative is used when configuring the IP address of the unit How ever if problems occur due to firewalls etc use Manual alternative instead 24 Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit The Remote alternative is explained as part of the section Connection using IP based connection method The Manual alternative is explained in section Manually changing the IP address IMPORTANT NOTE The unit can have any IP address but the unit and PC must always be in the same subnet For example IP for PC 194 9 227 250 and IP for the unit 194 9 227 251 and the subnet mask is fixed to 299 295 255 0 Installation and set up manual 208668 25 3 Installing the unit CRANEX Novus e Connection using the Direct Connection method 1 Standalone configuration Connect one end of the Ethernet cable to the unit the connector at the rear of the column and the other end to the PC Network configuration Connect one end of the Ethernet cable to the 4 unit the connector at the rear of the column and the other end to the network 2 Switch the Unit on 3 PC Start the PC and then open the dental imaging software that you install
25. l applicable local laws and regulations on patient information software This includes for example the Medi cal Device Directive 93 42 EEC and or the FDA During unit operation Read and familiarize yourself with the warn ings and precautions in the unit User s Manual When checking the alignment of the radiation beam protect yourself from radiation After the unit has been installed and set up advise the people who will operate the unit to familiarize themselves with the warnings and precautions in the User s Manual Installation and set up manual 208668 CRANEX Novus e 1 Introduction 1 4 Unit description Main parts FS Wall bar Exposure warning light Column Upper shelf aC 1 R Focal trough O Vertical carriage pm ee FA ao o J EJ m 74 Display and main Mirror control panel i at Cc Patient handles Midsaggital light Chin support Side control panel On off switch rear of column NOTE Rotating Unit Tubehead CCD sensor Installation and set up manual 208668 3 1 Introduction CRANEX Novus e Unit controls TIF O I L Status ready A Side control panel Lights key switches the positioning lights on and off Up down keys Return key drives rotating unit to the patient in out position PIO OWS B Main control panel Program keys adult pan child pan TMJ bitewing optional kV selection keys Exposure values
26. o take an adult panoramic A vs KA T exposure at 70 kV e P o Refer to the unit user s manual for information on how to do this Attach the ball pin tool to the chin support 6 Protect yourself from radiation Press and hold down the exposure switch to take an exposure 7 PC Use the measuring tools in the dental imaging software to examine the dimensions of the balls that appear on the image Magnify the image so that you can accurately measure the dimensions Installation and set up manual 208668 39 4 Checking the alignment and finishing the installation CRANEX Novus e 40 Distance left 2 0 mm If the image geometry is correct the center ball must be round with no more than 0 2 mm difference between the horizontal diameter and the vertical diameter Also the distance from the center ball to the furthest left hand ball Distance left and the furthest right hand ball Distance right must be the same with no more than 2 0 mm dif ference between them Horizontal diameter Vertical diameter Distance right 2 0 mm If the center ball is NOT ROUND and or the distances between the balls are NOT WITHIN THE TOLERANCE then the rotating unit RU or the chin rest must be adjusted See 5 2 Adjusting the image geometry IMPORTANT NOTE In some cases you may have to adjust the position of both the rotating unit AND the chin rest Installation and set up manual 208668 CRANEX Novuse
27. ons correctly Take a test exposure to verify that the unit operates correctly and the image is transferred successfully to the PC Protect yourself from radiation when taking the exposure Check the up down keys drive the unit up and down Check that the light key switches the position ing lights on and off Check that the lights come on when the mirror is opened Check that when the emergency switch is pressed the unit stops operating Finally replace all the covers that were removed Installation and set up manual 208668 43 5 Aligning the unit CRANEX Novus e 5 Aligning the unit 5 1 Aligning the CCD sensor If the sensor was not correctly aligned after car rying out the alignment check 4 1 Checking the alignment of the CCD Sensor the sensor must be repositioned and new beam images taken to confirm that it is correctly positioned 1 Remove the inner sensor cover from the rotat ing unit itis held in place with four 4 screws 2 To adjust the CCD sensor loosen the four nuts A that hold the CCD sensor in place and then adjust its position with the two screws B on the left hand side 44 22 Installation and set up manual 208668 5 Aligning the unit CRANEX Novus e Adjust and recheck the position of the CCD sensor until the beam is vertical and centered in the middle of the CCD aperture re a E _ Turn CCD lt gt amp Turn CCD counter clockwise i clockwi
28. play It shows the unit serial number the firmware version numbers and several function buttons IP Settings Installation commands and optionally Bitewing Activation Select IP Settings NOTE See section 4 for information about Installa tion Commands and section 3 7 for informa tion about Bitewing Activation Installation and set up manual 208668 29 3 Installing the unit CRANEX Novus e 30 7 The IP configuration modes will appear on the screen Remote or Manual Current IP address 194 9 227 251 Choose IP Configuration Mode MANUAL REMOTE 1 Select Remote 8 The IP address window will appear which shows the current IP address of the unit Current IP Adress 194 9 227 251 Q S Installation and set up manual 208668 CRANEX Novus e IP based Received IP Adress 194 9 227 250 9 3 Installing the unit Standalone configuration PC In the IP address field key in the de sired IP address of the unit for example 194 9 227 250 and then click the Send to Device button Network configuration PC Key in the new IP address obtained from the network administrator into the IP address field key and press the Send to Device but ton Device IP address v Enable changing IP address 194 9227 7250 Send to Device 10 The new IP address will appear on the screen 11 Touch the OK button to accept the IP address and then the Arrow button to return to the main s
29. ply ccccceceeeeeeeeceeeeeeeeeeeeeenes 21 O22 POD aM NGC esrantiie Giveticet ound Aataaimnetustdeanadaveauer est iced een nieeeee beeen ay 22 Installation and set up manual 208668 V 36 Connecting the unit 10 1NE PC omessi tere eeeeseoiaees 23 COME CUOMO DUON Sacvaseccanwexsachansstaevianerseswveanertedeaaunaaueidanndaeastamuaa eased 23 DUI Cle ON GF eea a a ocmea unt ene eben caret 23 REID gl Coenen eee oe ao on A Tot A 23 CONNECTION IME TNOGS Seiren a A wanda 24 Drect CON MOC HON cs ioc5s uss cosnasncas ovnacecescenamavatacnentubeo E aT 24 IP DASCG GONMECIION srm a ea hics idem hedenma ental cacy and Seemed a a 24 Connection using the Direct Connection method ccceceeeee scenes 26 Connection using the IP based mMethod ccccccceccceeeceeeeeeeeaeeeseees 28 Manually changing the IP addres eerie eee 32 WICITIRCOMNECE adissa e EEEN 34 3 7 Activating the optional bitewing PrOGraM ccccccsecceeeseeeeeeeeeeeeeeaeeaes 36 4 Checking the alignment and finishing the installation 37 4 1 Checking the alignment of the CCD Sensor cccccecceeeeeeeeeeeeeeeeees 3 4 2 Checking the image geometry ball pin phantom test ceee 39 4 3 Checking the positioning liQhts cccccccceeccseceeeeeseeeseeeseeeeeeeeeeeeaeeees 41 WIGSAG Ital NGM resnie ieser r e O erutatiuaetoeadoeten 41 Frankin ONE eneon 42 FOCaLTOUOM NOM sectasceuicucvscsggeua
30. rkstation information for exam ple user name location etc can be entered into the field next to the work station identifier number Device Autorelease timeout seconds Cancel The Device Autorelease timeout is the length of time that the unit will remain reserved and usable by a PC After the set time elapses the PC automatically releases the unit so that it can be used by another PC in the network the unit can be reserved in advance from another PC The default setting is 300 seconds This can be changed by keying in a new value Installation and set up manual 208668 CRANEX Novus e 3 Installing the unit 3 PC Click OK to connect the PC to the unit NOTE An automatic technique will automatically lo cate the unit within the local area network and connect the PC PC Repeat the above process for all the other PCs in the network Make sure that you give each PC a different Workstation identifier Check the installation by starting image cap ture using the imaging software If the Use Multi Connect was selected the Workstation identifier of the PC 1 8 being used will appear on the unit display E Status ready 2 Installation and set up manual 208668 35 3 Installing the unit 36 CRANEX Novus e 3 Activating the optional bitewing program sN Novus SOyyxxxx Fw 1 00 Core 36 Graphics 1 Bitewing Activation NOTE If the Bitewing Activation button does NOT appear it
31. se Move i Move i CCD CCD to right to left 4 gt 4 3 Touch the Arrow button to exit the Still Mode and return to the main menu Installation and set up manual 208668 45 5 Aligning the unit CRANEX Novus e 5 2 Adjusting the image geometry IMPORTANT NOTE In some cases you may have to adjust the position of both the rotating unit AND the chin rest Center ball not round If the center ball is NOT ROUND then the position of the rotating unit RU must be must be adjusted 1 Loosen the two nuts that hold the guide pin as sembly in place Turn the adjusting nut counter clockwise to move the rotating unit towards the column and clockwise to move it away from the column a TE RDRRRDODRBOL LLL 7 2p A move RU di AAN towards column A A A j a4 n B move RU away from column A Move rotating unit towards the column B Move rotating unit away from the column a j 46 Installation and set up manual 208668 CRANEX Novus e 5 Aligning the unit 2 Re tighten the guide pin assembly nuts after the adjustment 3 Take another ball pin exposure to confirm the center ball is round Also verify that the dis tances from center ball to left and right pins are equal if not proceed to the next section Distances between left and right pins not equal Distances between center ball and left and right balls not equal If the distances betwe
32. stem Consideration relating to the choice shall include use of the accessory in the PATIENT VICINITY evidence that the safety certification of the AC CESSORY has been performed in accordance to the appropriate IEC 601 1 and or IEC 601 1 1 harmonized national standard 2 3 The dental imaging software The dental imaging software for example SCANORAor DIGORA for Windows not in USA that is installed in the PC used to with the unit must be MDD compliant 2 4 Space requirements When installing the unit make sure that there is enough space at the front and sides of the unit to allow patients to enter and exit the unit easily Patients in wheelchairs will require more space than standing patients the unit is positioned at least 1 85 mm 73 in away from any non medical electrical or elec tromechanical equipment the unit is positioned so that the operator when protected from radiation can see and hear the patient during an exposure Installation and set up manual 208668 CRANEX Novus e 2 Pre installation requirements 2 5 Unit dimensions 2315 mm 91 in 950 1750 mm 27 in 80 in 150 mm 6 in Installation and set up manual 208668 9 2 Pre installation requirements CRANEX Novus e 2 6 Fixing hole dimensions 203 5 mm Center to hole 2275 15 mm Standard column leg 2185 15 mm Short column leg 10 Installation and set up manual 208668 CRANEX Novus e 2 Pre installat
33. tation The CRANEX Novus e User s manual The CRANEX Novus e Service manual not sup plied in the delivery The installation and user manuals for the dental imaging software to be used with the unit for ex ample SCANORA or DIGORA for Windows not in the USA Installation and set up manual 208668 1 1 Introduction CRANEX Novus e 1 3 Warnings and precautions During installation When installing the unit always observe local and national safety regulation concerning the installation and use of dental x ray equipment Failure to install the unit in an approved loca tion according to these installation instructions may cause the device to be dangerous to both patient and operator The aperture plate in the collimator is made of lead Pb which is a toxic material Do not touch it with your bare hands Be careful when working on the unit when the covers have been removed Some mechanical parts have sharp edges that can cause injuries if mishandled Some internal components become hot during operation Take suitable precautions to avoid burning yourself Some electric components are high voltage and can be lethal if touched Whenever you are making adjustments to the unit disconnect it from the main power supply before making the adjustment If the unit is to be used with a 3rd party im aging application software not produced or supplied by SOREDEX the 3rd party imaging software must comply with al
34. the unit is to be installed and the position from where the user will take exposures must be correctly shielded from the radiation that is generated when the unit is operated Since radiation safety requirements vary from country to country and state to state it is the responsibility of the installer to ensure that all safety requirements are met Do not install the unit in environments where there are corrosive or explosive vapours Special steps regarding EMC need to be taken when installing the unit For more informa tion refer to the EMC declaration in the user s manual The unit must be installed at least 1 85 m 73 in away from any non medical electrical or electromechanical equipment The unit must be connected to Its own dedi cated power supply 100 to 120 VAC or 220 to 240 VAC Extension cables MUST NOT be used with the unit Installation and set up manual 208668 T 2 Pre installation requirements 2 2 The PC CRANEX Novus e The PC to be used with the unit must be in stalled in a location that meets all local and national safety requirements with regards the connection of a PC to an x ray device The connection of the unit to the PC must meet EN60601 1 requirements The PC must be positioned at least 1 85 mm 73 in away from the unit The use of ACCESSORY equipment not com plying with the equivalent safety requirements of this equipment may lead to a reduced level of safety of the resulting sy
35. ting unit and vertical carriage Place the spirit level widthwise on the upper shelf and level the unit in the left right direc tion Make small adjustments by loosening the wall bar fastenings and moving the top of the col umn to the left or the right to level the unit Make large adjustments by moving the base of the column left or right When the unit is level in the left right direction place the spirit level lengthwise on the upper shelf and level the unit in the forwards back wards direction Adjustments can be made by moving the base of the column backwards or forwards Installation and set up manual 208668 15 3 Installing the unit CRANEX Novus e NOTE If the wall bracket alone does not hold the unit in position rigidly enough or the unit is to be used in an area prone to earthquakes attach the base of the column to the floor Make sure that the unit is level and then mark the positions of the two fixing holes on the floor and then drill two holes of a suitable size for the 8 mm 5 16 in floor fixing hardware to be used 7 Check once more that the unit is vertical and then tighten all the fixing screws and wall bar fastenings 8 Pull the front cover from the upper shelf and then remove the two 2 screws that hold the top cover in position and then slide it off 9 From the upper shelf unscrew the guide pin Iddi Guide pin in and two holding screws from the base plate PE transportation DO NOT
Download Pdf Manuals
Related Search