Home
(For official use only) - rdso
Contents
1. recording cum test car shall be made air conditioned except DG set compartment b Suitable ducting arrangement for proper distribution of conditioned air shall be provided Suitable thermal insulation arrangement shall be provided in the DG set compartment to avoid heat transfer to staff equipment area air conditioned space Suitable insulation shall also be provided to avoid transmission of noise of DG set compartment to air conditioned space The car shall be provided with modular design roof AC package unit of adequate capacity which shall be capable to work during service conditions as given in this specification At present Indian Railways are using roof mounted air conditioned package of approximate cooling capacity of 20 000 K cal hr 6 5 TR which conforms to RDSO specification 64 6501 93 Effective from 4 7 4 8 4 9 no ELPS SPEC AC 03 Aug 1995 with latest amendment and its control panel to RDSO spec no ELSP SPEC AC 04 Rev 1 1996 with latest amendment Keeping in view the maintenance and repair requirements the supplier shall consider using air conditioning package unit as is being used by Indian Railways for their coaching stock as described in above Clauses If it is proposed to use different capacity and or design the same shall meet generally the requirement of above specifications and spares should be available in India
2. For official use only GOVERNMENT OF INDIA MINISTRY OF RAILWAYS SPECIFICATION FOR B G SELF PROPELLED OHE RECORDING CAR FOR ELECTRIC TRACTION SPECIFICATION No TLSPC OHE SPRC 0011 Issued by T I DIRECTORATE RESEARCH DESIGNS amp STANDARDS ORGANISATION MANAK NAGAR LUCKNOW 226 011 PRICE 10193 Effective from SPECIFICATION FOR SELF PROPELLED OHE RECORDING CAR FOR ELECTRIC TRACTION SPECIFICATION NO 0011 Amendment Date of Total pages including Amendment Revision Number Amendment annexure 0 NA First issue PREPARED BY CHECKED BY APPROVED BY SIGNATURE DATE DESIGNATION SE CAR DTI H EDTI COPY NUMBER ISSUED SIGNATURE DATE sess ISSUED TO ect n T NOTE This specification is property of RDSO No reproduction shall be done without permission from DG RDSO This specification is not for general use 20193 Effective from TI SPC OHE SPRC This draft specification for self propelled NETRA car for recording of OHE parameters has been prepared T Directorate of RDSO Lucknow Government of India Ministry of Railways Manak Nagar Lucknow 226 011 India and uploaded on RDSO web site All interested manufacturer and supplier of car may give their suggestion com
3. 4 1 4 2 climatic conditions existing throughout India the equipment and their mounting arrangement shall be designed to withstand vibrations and shocks as specified in IEC 61287 and IEC 60571 for the inverters and electronic equipment respectively Complete Vehicle control and inverter systems with their controls and gate drive electronics shall be protected from dusty environment by providing well sealed enclosures Necessary precaution should be taken against high degree of electromagnetic pollution anticipated in the OHE Car The cooling system shall be designed to take care of tilting and centrifugal forces which would normally be encountered in service OPERATING REQUIREMENTS half worn wheels Maximum test speed 115 km h Maximum operating speed 105 km h Maximum Tractive effort at start 76 ton from start till 21 1 km h or superior Installed power standard 1600 HP Power input to traction site 1450 HP approx Speed Vs TE characteristic Refer graph at Annexure IV The offered equipment should be capable of meeting this characteristic The supplier will state the value of maximum starting tractive effort continuous tractive effort and continuous speed values that will be developed under dry rail conditions and also under all weather conditions which will be demonstrated during testing Supplier shall try to improve the performance beyond above stated values The tenderer shall clearly specify the
4. Over all dimension of one roof mounted typical AC package unit and its control panel are given below for your information and guidance Package unit control panel Dimension Package unit Control panel Length mm 2190 1300 Width mm 2250 500 Height mm 661 200 4 10 Circuitry 5 0 6 0 6 1 6 2 6 3 6 4 The load shall be suitably distributed based on standard practice Separate wiring circuits for 110V DC amp 240V AC power supply shall be provided to cater the segregated lightning amp fan loads for better reliability and availability of power supply in the OHE car Specification for electrical switches lamps holders plugs etc Electrical equipment such as switches lamp holders and other items shall conform to the following specifications 15 6965 Switches for use in Railway coaching stock 15 1258 Bayonet lamp holders 15 1293 Three plug and socket outlets IRS EA 199 For ceiling light fittings with clear glass gloves Power for head lights tail lights amp other safety lights Headlights tail lights flasher lights marker lights dash board lights and driver s cab lights shall be supplied from the alternator rectifier provided with diesel engine This is to ensure that failure in the other lighting system does not affect the mobility of the car Head light Twin Beam head lights shall be provided at both ends The head light shall conform to RDSO s specification
5. 2 1 2 2 2 3 2 4 2 4 1 2 4 2 2 4 3 V ELECTRICAL EQUIPMENTS AND POWER SUPPLY ARRANGEMENT Illumination Driving cabs DG set room staff cabins and instrument room shall be provided with adequate level of illumination at the working plan level 1m above the floor level and adequate lights exhaust ventilation to be provided for DG set room Driving cabs and staff cabins each shall be provided with two 110V 300 mm sweep fans conforming to 15 6680 ALTERNATORS Engine mounted auxiliary alternator of adequate capacity with rectifier for the speed range between idle and maximum of engine speed shall be provided on each engine to supply 24V d c for charging the battery provided for engine starting Engine driven Auxiliary Alternators with rectifier and voltage regulator of adequate capacity shall be provided The drive for the alternator shall be taken from auxiliary end of engine The auxiliary alternators shall cater to the following electric loads Two twin beam head lights one at each end LED Flasher Light and LED marker light 110 V supply for controls and cab equipments Charging of 110 V 120 Ah batteries Light amp Fan load of OHE recording car OVENS Axle Driven Alternator Apart from engine driven auxiliary alternators one axle driven alternator of 4 5kW capacity shall be provided to cater the above loads in case the OHE recording car is running idle or attached to a train A change over switch
6. 9 7 9 8 9 9 motor shall be fitted with roller suspension bearings Suitable arrangement for sensing of the motor temperature shall be provided to allow microprocessor based controls to sense and take required action to prevent motor failure The motor shall be designed so as to be capable of withstanding voltage fluctuations and other conditions caused by stalling and wheel slip under difficult operational conditions Extreme adverse environmental conditions as stated in the specification and vibrations due to average track conditions should be taken into consideration during the design of the motor The traction motor shall operate satisfactorily over the entire range of loading with ripple harmonic currents imposed from the supply system comprising of alternator rectifier inverter etc The manufacturer shall conduct necessary tests on the traction motor to establish compliance with this requirement The traction motor shall be of a high voltage and low current design such that it is compact The max voltage rating of the traction motor shall be commensurate with the alternator inverter voltage rating The traction motor shall be nose suspended The nose suspension shall be of approved design Each traction motor shall drive one axle of its motor bogie through single reduction gear drive enclosed in a rigid oil and water tight gear case firmly secured to prevent damage by movement and vibration under the most severe oper
7. Overload High cooling water temperature High lube oil temperature High exhaust temperature High intake temperature Any other Number of engines of this type in traction service Weight of engine excluding oil and water Weight of water contained in the engine Weight of oil contained in the engine Weight of major equipment Turbocharger Charge Air cooler Crank case bare Piston and connecting rod Cylinder liner Cylinder head Temperature of exhaust gas at turbo inlet at rated output under site conditions 87 8801 93 Effective from TI SPC OHE SPRC 24 25 26 27 28 29 30 31 Method of starting giving details of equipment Estimated period between top and major overhaul Periodicity of overhauling the following critical items Turbocharger Piston and piston rings Air and exhaust valve Main bearings Connecting rod bearings Fuel injection pump Fuel injectors Special design features of engine high lighting the measures which have been taken to achieve Lower specific fuel consumption Lower lube oil consumption Reduced thermal and mechanical loading of critical components High reliability Maximum availability General arrangement and dimensional details Characteristic curves for torque output and specific fuel consumption for different setting of the fuel injection pump Torque speed curve which the manufa
8. Fuel oil and cooling water circuit Grease oil chart with specification and quantity Wiring diagram with complete illustration of components Controls and safety features amp their test procedure List of special tools jigs and fixtures needed for testing commissioning maintenance and repair The manual shall include dis assembly and assembly procedure with specific mention of any special tools required for carrying out the above work Manual shall include a separate chapter indicating the service and condemning wear limits amp tolerances for various assembly sub assembly wherever applicable The manual shall contain a separate chapter pertaining to standard schedule of examination covering all equipments i e engine transmission axle drive cardan shaft controls etc for trouble free day to day maintenance of Car as per maintenance norms A separate booklet containing Drivers operating instruction accompanied by suitable illustration and diagram and lubrication chart shall be prepared and supplied COPYRIGHT This specification and all the related reference drawings issued by any authority of Indian Railway All rights conferred by the law of copyright and by virtue of International copyright convention are reserved to Indian Railways irrespective of the fact whether the same has been mentioned on any of such documents or otherwise Re production in whole or in part requires the prior written consent of Indian Railways
9. MR pressure and BP pressure in analog gauge picture form whereas the other one on the vehicle control 57 580 93 Effective from TI SPC OHE SPRC 21 22 1 22 2 22 3 microprocessor unit also digital display showing turbo lube fuel load meter data etc recall through an alphanumeric keypad The display on the vehicle control microprocessor unit shall be MENU driven and shall be made user friendly It shall display operational status of OHE Car fault messages and data packs running totals etc Any fault Alarm condition etc shall be shown on the display with suggested action if any and sounding of audio alarm for the benefit of the Driver It shall be possible to conduct self tests on various equipment by using a keypad to be provided on the display unit It shall be possible to cut out Traction Motors through keypad when required It shall also be possible to conduct self load test on the engine and Traction Alternator through the keypad The details of the various Display Screens Text Messages etc shall be finalized in consultation with RDSO USER SETTABLE PARAMETERS For flexibility of operation and future upgrades in the traction equipment it is desirable to provide user configurability for various control parameters like currents voltages horse powers temperatures pressures and speeds of the traction equipment It shall be possible to configure these parameters throug
10. The OHE Car shall be as per clause 2 2 Part I of Scope However details furnished therein are only indicative for the guidance of tenderer except those covered under Basic data in clause 2 of Part ll DETAILED OPERATING REQUIREMENTS AND OVERALL DIMENSIONS Basic Data A General Wheel diameter over tread New 952 mm B Specific to Gauge i Gauge 1676 mm ii a Maximum operating speed on level track when self propelled 105 km h b when coupled to a train 130 km h ii Maximum gradient 37 iv Maximum curve 10 v permitted axle load 20 32t vi Max Length of car 21337 mm vii Width of car 3250 mm viii Max Height from rail level 4025 mm i floor Height in unloaded condition 1282 mm x Wheel Base Minimum 2896 mm xi Max Height above rail level for center 1105 mm of Buffers amp coupler under unloaded condition Min Height above rail level for center 1035 mm of buffers amp coupler under fully loaded condition xiii Max Super Elevation 185 mm xiv Max Super Elevation Deficiency 100 mm GAUGE AND MOVING DIMENSIONS The OHE Car shall conform to max moving dimensions to diagram 1D EDO T 2202 of Indian Railway BG Schedule of Dimension revised 2004 with latest corrigendum slip as shown in with the pantograph in locked down condition 32 33of 93 Effective from 4 1 4 2 4 3 5 2 6 2
11. The contractor shall formulate Quality Assurance Plan QAP detailing the methodology proposed to be followed to ensure quality product QAP shall cover quality assurance procedures to be followed during all stages of design planning procurement manufacture testing commissioning and servicing The contractor shall define the role of each functional group in the organization for achieving the required quality of the products and submit a comprehensive document of QAP EXECUTION OF WORK The OHE Car shall be manufactured throughout in the best style of coach work and construction and shall conform to the best standards of the trade All components and sub assemblies shall be interchangeable in whole and or in part Sheets and plates shall be carefully straightened and flattened by stretching or by pressure Plates shall be sheared when cold and their edges evenly finished Welded components or members shall be correctly matched and accurate levels and clearances shall be ensured to result in perfect welds WELDING All welding procedures shall be documented by the Contractor Approval of the welding procedure shall be as required by BS EN ISO 15614 1 2004 Specification of Approval Testing of Welding Procedures or equivalent Approval of the welder shall be as required by BS EN 287 1 Specification for Approval Testing of Welders Working to Approved Welding Procedures or equivalent Arc welding shall be performed by the MIG process an
12. Two driving cabs one at each end with complete operating amp driving control and dash boards so that the car may be worked from either cab Driver s seat shall be on the left side Adequate leg space alongwith footrest shall be provided for the driver when he is seated ii Sitting space in each of the driving cabs for 2 persons in addition to the driver For this purpose a foldable cushion sheet shall be provided ii controls brake handle hand brake VCD footswitch for horn and indication lamps meters shall be within easy access and view of the driver iv Inter communication equipment between cabs and Inspection compartment through hand free sets with its own battery v 2numbers 24 V sockets for hand signals in each cab vi LED type flasher lights search lights and marker lights at both ends of the cab as per RDSO specification as mentioned in chapter 7 of this specification vii OHE voltage sensing device in both the cabs viii Full width splinter proof glass wind shield protected with expanded metal or BRC having least obstruction to visibility The wind shield shall extend upto the ceiling level so as to give clear view of overhead equipment ix The cab shall be adequately insulated against noise vibration heat and ingress of water and dust xi Step irons to driver s compartments Steel step irons shall be provided below the entrance to each driver s compartment and shall be so located as to provide a convenient
13. interchange shall be avoided except as required in the specification All system components and structual areas serviced as part of inspection or periodic preventive maitenance shall be readily accessible for service and inspection RELIABILITY In addition to meeting the performance requirements the coach shall incorporate high standards of reliability to ensure that operating cost and operation performance are optimized Reliability and maintainability requirements and goals shall be developed in terms of mean time between failures MTBF and or Mean distance between Failure MDBF and mean time to repair MTTR The Supplier shall provide the achieved quantitative reliability data of major subsystem equipment expressed in MTBF MDBF MTTR based on operations of proven cars fitted with similar equipment for a minimum of 3 years and 450 000 kilometers per car in revenue service for purchasers and IR s evaluation The MTBF shall be submitted for the ambient temperatures of 45 C 50 55 and at the temperature expected inside the engine compartments as per bidder s calculation for electrical electronic components 190f 93 Effective from 29 3 29 4 295 Contractor shall demonstrate by quantitative methods achievement of specified level of reliability for the cars and specific individual items of equipment The reliability and maintainability shall be moni
14. 1 6 kg cm and 16 25 t bogies a brake cylinder pressure of 3 8 2 Equipment in the driving cabs Following equipments pertaining to the brake system to be provided in the driving cab i Electro pneumatic driver s brake controller ii Self illuminated push button for remote control of EP brake system iii Indicator light for availability of power supply for EP brakes AIR FILTERS Air fillers assemblies of suitable type shall be selected and should preferably be heavy industrial dry type Filters at the compressor intake shall be of the dry filter type 43 44 93 Effective from 27 2 28 28 1 28 2 The filtering capability flow rate capacity and size shall be appropriate for the application and the ambient conditions like prevalence of heavy dust and debris in India It shall be possible to gain access to the filter element for replacement purposes without disconnection of any pipe fittings The design of capacity requirement shall take into account at least 2596 choking in air filters amp radiator fins ELASTOMERS All elastomeric parts shall be of neoprene unless otherwise required the elastomer shall be compounded and cured to perform satisfactorily in the temperature range specified in this specification The elastomers shall have high resistance to ultraviolet radiation weather washing fluids used by IR salt deposits and the lo
15. 2 4 2 4 1 2 4 2 2 4 3 2 5 2 5 1 The main members of the underframe sidewalls end walls and roof shall be strain gauged The location of the strain gauges shall be determined in consultation with the contractor at the design stage based on the result of the Finite Element Analysis The superstructure shall be subjected to vertical loads and combination of vertical and squeeze load as specified in UIC 566 and the stresses at specified locations the deflection and body spread shall be recorded The stresses so recorded shall normally not exceed 2 3 of the yield strength of the material in case of vertical load alone and shall not exceed 90 of the yield strength in case of application of combination of vertical and squeeze loads However the acceptance criteria for all the parameters recorded in this test as well as the detailed test scheme shall be finalized at the design stage in consultation with the contractor Tare Weights The Contractor shall take the tare weights of OHE Car which shall be reported to the Engineers as for the ready unit Clearances The OHE Car completed in all respect shall be placed on level straight track and the coupler heights spring heights bogie clearances and other clearances shall be checked under tare and loaded conditions The unit shall under these load conditions pass through a structure representing the moving gauge to diagram as shown in Annexure lll Tests on Maximum Curves The co
16. 3 PART MECHANICAL REQUIREMENTS CARBODY The car body and attached equipment shall be designed to provide for adequate clearance between car body and bogies for worst case operating conditions except for any stops attached to the OHE car body for limiting bogie movement or for bogie lifting during maintenance Worst case conditions may result from horizontal and vertical curves tracks super elevation worn wheels maximum passenger load roll yaw lateral motion and suspension system failures The structure of the OHE Car body including shell should be suitable for severe testing and recording of OHE parameters services and have a design life of at least 35 years in the services under 20096 overload conditions with no fatigue or permanent deformation failure Cabs of both ends of the OHE Car shall have streamlined design to give an aesthetically pleasant appearance Use of fibre moulded sheets or any other similar material for the purpose of giving modern aesthetic design shall be avoided as far as possible The body shell shall be of integral lightweight construction consisting of separate assembly groups for under frame sidewalls roof and end walls joined together to form a tubular structure These assembly groups shall be made from the rolled sections or pressed plates and plain sheets which are suitable for welding The car body shall be made by spot resistance welding as suitable and internationally acceptable welding
17. No ELRS SPEC PR 0022 Rev 1 Oct 2004 The operating voltage of head light shall be 24 V DC Tail light Two aspect red and white LED type 24 V 15 W tail light shall be provided at each end to comply with general rule of Indian Railway Flasher light LED Flasher light as per RDSO s specification No spec no No ELRS SPEC LFL 0017 Rev 1 Sept 2004 or latest shall be provided 65 66of 93 Effective from 6 5 6 6 7 0 8 0 9 0 Marker Light LED Marker light as per RDSO s specification No ELRS SPEC PR 0022 Rev 1 Oct 2004 or latest shall be provided Search Light Car shall be provided with two 250 W searchlights with halogen lamps one on each end for inspection of the overhead equipment while on the run Searchlight shall provide a high intensity illuminating beam and capable of swiveling on universal joint type supports Wiring Electrical wiring shall conform to IRS E 45 1977 However only copper conductors shall be used for wiring Horns The car shall be fitted with two horns with different tones on both sides Horns may be operated by battery or compressed air These shall be operated by a footswitch provided within the access of the driver Wipers electrical operated wipers to be provided 66 67of 93 Effective from TI SPC OHE SPRC 1 1 1 2 1 3 PART VI TESTING amp INSPECTION AC AC TRANSMISION SYSTEM Ty
18. Railway personnel so that they acquire full knowledge of major assembly sub assembly used in OHE Car The training shall be helpful in trouble shooting maintenance and operation of the Car Besides the above adequate number of maintenance and operating staff shall also be trained in the homing shed during the commissioning of the OHE Car The training will broadly cover the following aspects directly connected to the car and will be processed as on job training i Design development of car including CAD FEM practices ii Manufacturing technology and process engineering of the coaches including design and manufacturing of Jigs Fixtures Tooling iii Quality assurance systems quality plans and inspection procedures including gauges iv Maintenance engineering and repair practices for OHE Car bodies as far as available with contractor 15of 93 Effective from 19 2 20 20 1 20 3 20 4 contractor shall endeavor to where necessary arrange to train IR personnel in the premises of his suppliers in design manufacture quality control and commissioning vi The living costs of the IR personnel and the transportation cost shall be borne by IR The transportation between hotel and place of training will be provided by the Contractor For any additional training by IR over and above described The contractor shall arrange training of IR personnel at the works
19. System traction machines control equipment etc 45 4601 93 Effective from 2 SCOPE 2 1 Scope of supply of equipment for 5 car unit shall be as under SI Equipment Description Quantity No per DPC 1 Suitable horse power of proven make fuel efficient diesel engine 1 No under standard condition with either GAC or PG Woodward actuator eliminator filtration system engine driven alternator for charging battery for engine cranking hydrostatic cooling equipment complete with radiator Fuel pipes check valve hoses and fittings 2 Traction Alternator to be directly coupled to above diesel engine 1 No 3 Base Rail arrangement with mounting brackets amp bolts for mounting 1 set Engine and alternator 4 IGBT based traction converter system including power rectifier DC link 2 Nos or and associated controls Hardware and software The software for 4 Nos converter control system shall be compatible with that of Vehicle Control as per System confi guration 5 Microprocessor based Vehicle Control System Hardware and software 1 No along with all control protection and indication equipment required for proper functioning of the OHE Car This shall be compatible with other equipment on OHE Car such as selected diesel engine traction alternator traction converter etc 6 Microprocessor based engine governor
20. This shall interface with 1No Microprocessor based Vehicle Control System 7 Three phase induction motors with gear wheel and gear case suitable 4 Nos for input supply from traction converter s 8 Suitable Auxiliary Generator for supplying auxiliary power for battery 1 set charging controls light fan etc 9 Air Compressor with other accessories 1 No 10 All the power contactors MCB s relays etc 1 set 11 Battery a 24 V 450 AH for engine starting set b 110 V supply of suitable AH capacity for controls set 13 Driver s Desk No 1 1 12 Speed indicator 1 set 1 1 14 PO Laptop based software tool for downloading the fault data packs No viewing and changing the user settable parameters along with user license 3 ENVIRONMENTAL CONDITIONS 3 1 The complete microprocessor based vehicle controls and inverter systems shall be required to work continuously at full load under service conditions as indicated in the chapter of Part l 3 2 All the equipment shall be designed to withstand ambient conditions as indicated in chapter of Part I without any harmful effect even after sustained working at 100 load factor Complete system shall be suitable for rugged service normally experienced for rolling stock where OHE Car is expected to run up to a maximum test speed of 115 km h in varying 46 470 93 Effective from TI SPC OHE SPRC
21. equipments access doors and line equipment shall be provided to ensure 1 Safety of men working and 2 Stability of the car while in operation The tenderer shall indicate the interlocking and safety aspects he proposes to incorporate 3 The entire car including bogies superstructure along with equipment is to be effectively earthed as per standard practice for rolling stock 28 2901 93 Effective from 3 9 Safety of personnel As the signals for various parameters shall be collected at 25kV AC it is of paramount importance that the safety of personnel working in the OHE car is guaranteed under all circumstances Necessary safety measures including suitable system and earthing shall be provided by the successful tenderer to ensure this 3 10 Performance capability tests 3 10 1 The self propelled OHE car shall be subjected to tests at various speeds upto a maximum of 105 km h and 10 96 above maximum designed speed of 105 kmph and in different sections under varying conditions to establish the performance of the complete system and various sub systems based on the test schedule mutually agreed before commissioning 3 10 2 The design of self propelled OHE car should have proven and performed in service successfully to meet the performance parameter in the field for period of two year in India 3 10 3 The results of the tests should indicate that the system is capable for me
22. foot hold without infringement of maximum moving dimensions The general layout and arrangement of equipment in drivers cab shall follow UIC CODE 651OR latest edition with respect to dimensions safety features furnishing lighting ventilation noise level field of view drivers desk and seats Spotlight shall be provided at suitable locations Each cab shall be provided with the following Two pneumatic motor driven wind screen wipers with emergency manual control Two fans for crew Two fire extinguishers and one first aid box Two dual tone heavy duty pneumatic horns elo 27 280 93 Effective from TI SPC OHE SPRC xiv Cab Floor The cab floor shall be clear of all discontinuities and shall not incorporate access panels to under floor mounted equipment junction boxes and cable ducts It shall be possible to undertake water washing of the cab floor without damage to the floor or equipment xv Cab Lighting The cab shall be provided with ceiling lights providing 200 lux at 1 m above floor level It shall be operated automatically by the opening of either cab door and can be switched off manually form within the cab 3 8 2 Staff and officer s Cabins 3 8 2 1 Two separate cabins one for officer with two berths and the other for staff with four berths shall be provided with air conditioning cabins shall have separate entry and preferably not over the wheels and made sound proof as
23. in the vicinity signals for better visibility A cantilever assembly mainly comprising of high tensile steel tubes and solid core porcelain insulators is attached to the traction mast with suitable mast fittings The catenary is freely suspended from the cantilever assembly and the contact wire is registered at the required position by an aluminum steady arm The complete cantilever assembly upto solid core porcelain insulator is live at 25 kV 50 Hz AC system In tunnels due to restricted head rooms the encumbrance is reduced as required the minimum being 250 mm approximately The tension length of the catenary and contact wires are normally 1500 m and distance between overlaps being 1300 m approx An anticreep i e a fixed point is provided on the catenary approximately at the mid point of each tension length In a regulated equipment as adopted on Indian Railways a constant tension of 1000 kgf is maintained on the catenary and the contact wire by counter weights through an auto tensioning device Unregulated OHE is also in use but normally in yards only the contact wire tension for tramway OHE used in secondary lines is 1200 kgf 82 8301 93 Effective from TI SPC OHE SPRCO At uninsulated overlaps the air gap between the two wires is 200 mm At insulated overlaps similarly the two overhead equipments are separated by an air gap normally of 500 mm Turnout and crossovers are equipped with
24. indicate appropriate cleaning chemicals to maintain the appearance of the exterior of the car body Only colored stickers bands shall be provided on the exterior For other areas protection against corrosion and painting of cars shall be as per UIC 842 5 37 38of 93 Effective from 7 1 7 2 7 3 7 4 7 5 7 6 7 7 9 1 9 2 ROOF AND FLOOR CONSTRUCTION Roof Structure Equipment mounted under the roof suspended from the roof structure shall be bolted to the framing members The framing members shall reinforce in sub assembly to accept the equipment load The Supplier shall ensure the adequate water drainage from the roof such that no water is discharged into the vicinity of passenger doorways Rain gutters shall be provided over windows and doors Roof equipment arrangement design shall not permit accumulation of water at all in standing or running condition Floor construction The floating floor shall be constructed so that all applicable noise vibration strength and fire endurance rating requirement are met A multiplayer hard wearing non slip fire retardant floor covering having high abrasion resistance water proof and sealed resistant to staining and easily cleanable using conventional floor cleaning methods and suitable cleaning agent should be provided The service life of the floor covering shall be at least 3 years The floor construction shall be
25. into five categories namely i Interruptions having a duration between 2 5 to 5 ms M do 5 to 10 ms do 10 to 15 ms d dE do 15 to 30 ms B do more than 30 ms The contact force values shall be grouped into the following six categories for processing or presentation with reference to any of the parameters being sensed 4kof 4 1 kgf 8 kof 8 1 kgf 12 kgf 12 1 kgf 16 kgf 16 1 kgf 20 kgf and Greater than 20 kof Recording facilities 2 6 5 1 All parameters shall be recorded and archived on a suitable multi channel recorder The storage space shall be adequate for storing information for a cumulative run of 10 000 kms or 90 days which ever is less 23 2401 93 Effective from 2 6 5 2 measured and recorded data shall be converted from analogue to digital form classified analysed and stored on an On Board microprocessor based data acquisition and analyzer system It should be possible to generate suitable reports involving simple logic from the database 2 6 5 3 It shall be possible to print out all or any of the parameters in juxtaposition as a function of distance or mast location without any classification if desired Normally the data shall be required to be printed after classification and analysis as specified For example in a test run of 10 minutes covering 25 km
26. kept for field trials for a 500 Kms All the modifications required due to defects noticed or design improvements found necessary as a result of the test trial shall be carried out by the tenderer in the least possible time Total cost of such modifications design changes shall be borne by the manufacturer If mutually agreed between manufacturer and RDSO witnessing of tests on equipments used in OHE Car may be waived for sets manufactured by sub vendor Successful tenderer shall submit the test certificates of the equipments Instrumentation a All the instruments used for testing should be duly calibrated The calibration certificates are to be shown to RDSO representative s on demand b Value of the fundamental component and THD of traction inverter output will be measured by power analyzer during the prototype test at various mutually decided pre set points True RMS value of output voltage is also to be measured for record MECHANICAL TEST ON PROTOTYPE COACHES UNITS RAKES The following tests shall be conducted only on the OHE Car SQUEEZE TEST OF SHELL This test shall be done at the contractor s premises and shall be witnessed by the IR s representative if so desired by the IR 2 1 2 The Car shall be subjected to static vertical and squeeze head on loads tests 67 680 93 Effective from TI SPC OHE SPRC 2 1 3 2 2 2 2 1 2 2 2 2 3 2 3 1 2 3 2 2 3 3 2 3 4
27. minimum guaranteed reliability of the equipment in terms of km failure 4 3 tenderer shall clearly specify the efficiency of various equipments and also the overall 44 4 4 1 4 4 2 4 4 3 transmission efficiency ADHESION REQUIREMENTS Microprocessor based control system shall be provided with state of the art adhesion improvement system The system should be able to optimize the adhesion for all weather conditions dry rail wet rail conditions and all track conditions mainline branch line and station yards and operating conditions starting running braking The system offered shall be so designed as to reduce operation of sanding system substantially The torque pulsations of traction motors arising out of imperfections in waveform shall be controlled in such a manner that the coefficient of adhesion between wheel and rail is utilized fully in entire speed range of OHE car The mechanical transmission shall be adequately designed to cater for loading imposed by torque fluctuations Tenderers are required to indicate the expected level of adhesion in various conditions The proposed inverter and vehicle control system shall achieve far better adhesion performance compared to existing OHE Car which are based on AC AC transmission system 47 480 93 Effective from TI SPC OHE SPRC 4 5 4 5 1 4 5 2 4 5 3 4 6 5 1 5 2 5 3 EMI REQUIREMENTS The OHE Car shall be wor
28. must have designed manufactured and supplied any one or both of the following a EMU DEMU Locomotives Tower Wagon b OHE parameter measuring equipments The firm company shall submit details of such vehicles with performance certificates Manufacturer should have infrastructure as laid down in Annexure Il GENERAL DESIGN REQUIREMENTS Deviation from this specification may be proposed if it intends to improve the performance utility and efficiency of the OHE Car as a whole or part thereof as options with separate prices However consideration of such deviations shall be at the discretion of the IR and shall be on the basis of merit All such deviations shall be accompanied with complete technical details and justification for the proposed deviation The entire equipment shall be designed to ensure satisfactory and safe operation under the running conditions specified in Part Ill and especially under sudden variations of load and pressure as may arise under working conditions due to faulty operation and short circuits 70193 Effective from TI SPC OHE SPRC 4 3 4 4 4 5 4 6 5 1 5 2 5 3 5 4 5 5 The design shall also facilitate easy erection by means of suitable tools and equipment inspection maintenance and replacement of the various units comprising the equipment All working parts of the control and auxiliary circuit specifically electronics and PCBs shall be suitably covered to
29. of proven type available indigenously The car shall be provided with Marker light to RDSO specification for LED Marker light for electric loco diesel electric loco No ELRS SPEC PR 0022 Rev 1 October 2004 The car shall be provided with flasher lights to RDSO Spec for LED based Flasher light units for electric loco diesel hydraulic loco EMU DMU No ELRS SPEC LFL 0017 Rev 1 of Sept 2004 COMPRESSOR One belt driven air compressor ELGI make type TRC 2507 or suitable proven design shall be provided in OHE Car OEM shall specify the correct grade of compressor oil suitable for operation of compressor in climatic conditions specified in the specification PIPING All pipe joints will be as per ICF standard practice Schematic piping to suit the engine shall be to the relevant ICF drawings Flexible pipes shall be provided at all the locations prone to vibrations LUBRICATION Grease nipples shall conform to IS specification No 4009 All the grease nipples amp adapters where used shall be tack welded to prevent them from unscrewing and falling off in service ROLLER BEARINGS Roller bearings used on the OHE Car at various locations shall be from following proven sources viz SKF FAG TIMKEN NEI NTN NSK FIRE EXTINGUISHER Three Halon 1211 type fire extinguishers shall be provided one in engine compartment and others in Driver s cabs 62 630 93 Effective from TI SPC OHE SPRC 1 0 1 1 2 0
30. or fittings The Contractor shall provide such additional materials or fittings as may be required or arrange for test pieces to be incorporated in forging and castings as required by the Inspecting Officer and for their removal in his presence for test 13of 93 Effective from 14 4 14 5 15 15 1 15 2 15 2 15 3 1 15 3 2 15 4 purposes All tests in works of the Contractor and their sub contractors independent tests shall be paid for by the Purchaser or the Contractor depending on whether the tests show that the material is is not to specification No work shall be dispatched or packed until it has been passed by the Inspecting Officer but such passing shall in no way exonerate the Contractor from their obligation in respect of quality and performance of the Car In the event of dispute between the Inspecting Officer and the Contractor the decision of the Purchaser shall be final and binding TESTING OF OHE CAR The Supplier shall manufacture the OHE Car in all respect and shall offer for testing before dispatch The tests laid down in Part VI including test of energy consumption shall be carried out Functional tests on measuring equipments and their electronic interface shall also be conducted Successful tenderer shall submit complete details about the protocol Details of test scheme for the Car shall be finalized during design stage After ins
31. point of difference between the specification and or exhibited drawings that this specification fails to clarify the tenderer shall submit each such item to RDSO for immediate clarification Any additional item of work or equipment which may be considered necessary by the purchaser after placement of order and during the process of manufacture shall be carried out by the successful tenderer on the terms and conditions mutually agreed to between the purchaser and successful tenderer The interior where the computers and instrumentation system and living accommodation etc are provided shall be air conditioned with maximum relative humidity of 40 60 and average dry bulb temperature of 20 25 C However the instrumentation of OHE recording car should be capable of performing satisfactorily upto the following maximum temperatures metallic surface temperature under Sun 75 C max and in shade 55 C max The roof mounted equipments should therefore be capable to perform satisfactorily under such a high metallic surface temperature The system and instrumentation offered shall be of such design and manufacture which have proved satisfactory performance in the tropical climate similar to that of India QUALIFYING CRITERIA Any firm company wishing to participate in the tender should be an existing Rolling Stock manufacturer having adequate experience in Design Manufacture erection testing and commissioning of Rolling stock The firm company
32. separately for IR s workshop carrying out major overhaul and for maintenance depot for carrying out regular maintenance and quote accordingly The finalized lists of maintenance and additional tools shall be considered during commercial assessment of the bid The Supplier shall demonstrate to the IR the satisfactory functioning of the tools jigs amp instruments supplied vide the Clause 20 4 TESTING KIT The contractor shall indicate testing equipment required for ensuring optimum performance and trouble free service of the car as well as their major assemblies and sub assemblies The tenderer with complete quotations shall submit details of testing equipments SPARE PARTS The tenderer shall submit a list of spare parts and special tools both indigenous and imported indicating the name and address of the manufacturers as detailed below List A Catalogue of unit spares indigenous and imported of the principal assemblies of the Car such as the diesel engine transmission compressor measuring equipments etc with price List B Recommended maintenance spares for two years initial requirements The tenderer shall submit the list of such spare parts giving their detail description specification source of supply part number of the supplier service life and price of each part The total value of the spares to be supplied shall be limited to 596 of value of the OHE Car ordered The list will be reviewed by purchaser and the lis
33. shall be provided to RDSO specification no C K 408 The power cables of TM should be so arranged on either side of centre pivot so that parking brake cylinder while on run and on load does not hit the cables Piping and Pipe Fittings Seamless stainless steel pipe bright annealed to ASTM A 269 Gr 304 which can be bent cold shall be used The layout of piping shall be designed to keep all pipes especially the brake cylinder pipes as short and straight as possible Bends should be used throughout but where elbows have to be used they shall be of round type Where the pipes themselves are bent their internal area shall be maintained uniformly Double ferrule pipe fitting consisting of body front ferrule back ferrule and nut shall be provided The body and nut will be of carbon steel to ASTM A 108 Grade II with electro cobalt zinc plating with chromic passivation The front ferrule and back ferrule will be made from Stainless Steel to ASTM A 276 TP 316 SS and conforming to ICF specification no ICF MD SPEC 166 with latest amendments All pipes shall be adequately clamped to the frame assembly with proper clamps Flexible hose connections conforming to spec SAE 100R only shall be used Brake Blocks The K composition type brake blocks non asbestos type to RDSO specification no C 9508 and C 9809 with latest revision amendment shall be used all DPC and TC coaches The 20 32 t axle load bogies should have brake cylinder pressure of
34. such that it does not permit water to seep through the floor and cause corrosion to floor underframe component Indian Railways experience is that most of the corrosion takes place due to seepage of water through the floor and through the window opening and door opening The non skid floor structure shall be designed so as to minimize the life cycle cost of the floor over its designed value The openings in the flooring for the passage for pipes and cables shall be constructed as to prevent any seepage of the oil and in addition give effective protection against the spread of any fire originating beneath the bogy Adequate drain holes for floor water drainage at each doorway drain pipe at one meter apart in whole area of engine room and floor under the seats and at points where water is likely to accumulate should be provided Stainless steel drain pipes having top end of bell mouth type fitted with stainless steel mesh should be provided to prevent water from spreading on the underside of the coach structure or dripping on to the running gear Engine Room The floor of engine room shall consist of stainless steel chequered sheet No timber or any other inflammable material shall be used for flooring of engine room VENTILATION Fans shall be provided liberally throughout the Car at suitable location for ensuring adequate comfort to staff DOORS OHE Car shall have four body side doors two in each of cabs Other doors on sidewalls shall pr
35. the contact wire measurement should be minimum 0 5 mm m j Mast identification system The GPS receiver shall identify the location of OHE masts co relating with measured data Geographical positioning system shall be utilized for the mast identification along the track The GPS optical mapped data is in text file and shall be required to be correlated with the software of measuring instrument system so that the location of the measured data is automatically displayed printed along with the event recorded Accordingly chart recorder report output shall indicate the exact location of recorded event giving the mast number Alternatively optical identification system can also be employed GPS data should be transferable to PC laptop using suitable software and accessories Antenna of sufficient cable length should also be provided The accuracy required for mast location shall be minimum 4 meter Any other method which is more accurate and suitable to measure at higher speed of recording car may be offered If the tenderer feels that his proposed method is superior to the methods given above Tenderer have to submit the detailed procedure and justification 22 23of 93 Effective from 2 6 2 6 1 2 6 2 2 6 3 2 6 4 2 6 5 for acceptance of the purchaser contractors design should have given satisfactory performance for a minimum period of two years on railway networks
36. the drawing document 18of 93 Effective from TI SPC OHE SPRC 27 28 28 1 28 2 28 4 28 5 29 29 1 29 2 incorporates confidential information its disclosure to third parties also requires Indian Railways prior written consent GUARANTEE For OHE Car supplied by the Contractor in case any part of the car failing or proving unsatisfactory in service due to defective design material or workmanship within 36 months from the date of delivery in India or 24 months from the date of commissioning of OHE Car at its ultimate destination in India whichever is later shall be replaced by the Contractor at his own expense unless otherwise specified anywhere in this specification Further should any design modification be made in any part of the equipment offered the period of 24 months would commence when the modified part is commissioned in service MAINTENANCE Bidder shall submit the basic maintenance schedules of the proposed equipment Minimum intervals between two maintenance schedules in the depot shall be 90 days and 3 years for major works in workshop major depot The maintenance programme prepared by Bidder shall have the following objectives 1 Enhancement of OHE Car availablity ii Minimization of maintenance costs iii Minimization of Car downtime MTTS meantime to restore serviceablity Modular design principal shall be employed Requirements for adjustment after module
37. the equipment failing or proving unsatisfactory in service due to defective faulty design defective material bad workmanship within a period of 24 months from the date of placement in service or 30 months from date of delivery whichever is earlier The period of guarantee shall stand extended by the time taken by the firm in replacing the defective component from the date of lodging of complaint by the user Railway All aspects of workmanship and design shall be covered by this guarantee The supplier shall immediately provide arrangement for rectification of failures reported under guarantee 59 6001 93 Effective from 25 25 25 2 26 26 26 2 27 28 28 1 If any equipment of the system has undergone major design modifications during the guarantee period guarantee period of the equipment may be extended as per mutual agreement between RDSO and supplier FAILURES DURING GUARANTEE PERIOD UNDER MAINTENANCE CONTRACT In case of any failures the details of failure and action taken to arrest re occurrence of similar failure in future with failure analysis report etc is to be submitted to RDSO In case of repeated failures necessary changes in design on the units put in service or in production line are to be made by the manufacturer Investigation tests if considered necessary are to be arranged conducted by the manufacturer MARK
38. the information may be required in the following format a of contact losses of 2 5 ms 4 5 ms b Location of every individual incident with reference to the nearest mast C Total loss of contact expressed as a percentage of total test time d Incidents and their duration of contact forces falling below 7kg 2 6 5 4 Suitable recorder is to be provided for recording all parameters in juxtaposition for off line 2 7 2 7 1 2 7 2 2 4 3 2 4 4 2 4 5 processing The resolution of the parameters recorded shall be commensurate with the variation of the recorded value Dimensional operating and other requirements Maximum moving dimensions shall conform to the enclosed Maximum Moving Dimensions Diagram ID 1 D of SOD 2004 Appendix ll with the pantograph in the lowered condition Infringements if any may be considered if within the profile shown in the above sketch The OHE car shall be capable of negotiating i Minimum radius of curve 175 m ii A radius of 213 m in case of 1 in 8 turnout with 6 4m over riding switch Maximum super 185 mm Elevation Maximum Super 100 mm Elevation Deficiency Maximum wind pressure 200 kg sq m 24 25 93 Effective from TI SPC OHE SPRC 3 1 3 2 3 2 1 1 CONSTRUCTION OHE RECORDING AND WORKING ENVIRONMENT The Construction of OHE recording car shall meet all the functional and perf
39. total contact loss duration with total duration of recording The contact loss measurement could be carried out with the help of an a c signal obtained from capacitor divider mounted on the roof This is passed through a voltage isolator before being conditioned to give no 21 2201 93 Effective from output when signal is present Whenever loss of contact occurs the conditioning circuit produces an output in pulse form length of which is proportional to the distance over which contact is lost The event should also be signaled by an audible alarm in the instrument room Any other method which is more accurate and suitable to measure at higher speed of recording car may be offered If the tenderer feels that his proposed method is superior to the methods given above Tenderer to submit the detailed procedure and justification for acceptance of the purchaser contractors design should have given satisfactory performance for a minimum period of two years on railway networks elsewhere f Stagger of the contact wire Stagger is defined as the distance of the contact wire from the center line of pantograph measured transverse to the track Suitable compensation shall be made for transverse oscillations of the locomotive OHE car which affect the center line of the pantograph from the vertical The system employed should enable measurement of stagger of two contact wires s
40. whole or part thereof may be proposed for consideration All such proposals shall however be accompanied with complete technical details and justification for proposed deviation Performance of OHE Car shall largely depend upon design of traction inverter and microprocessor based control system Therefore it may be noted that irrespective of whatever has been stated in this specification complete integration electrical mechanical OHE parameter measuring equipments as well as software controls of the offered equipment with the other equipment fitted on the Car shall be sole responsibility of the successful tenderer Successful tenderer shall also be fully responsible for proper mounting installation and commissioning of all the offered equipment as well as satisfactory performance of the Car in the field trials Offers from only those tenderers who have developed either self propelled vehicle or OHE parameters measuring system or both and have experience in manufacture and integration of equipment for 3 phase AC AC traction system shall be accepted Therefore tenderers must submit the evidence of successful track record of manufacture and integration of equipment along with the offer Preferably tenderer shall also submit detailed indigenisation plan with the offer Tenderer shall have manufacturing assembly and testing facilities for the equipment being offered for OHE Car Traction control converter microprocessor based Vehicle Control
41. 1999 with latest amendment shall be provided for controls amp lighting which cater to all auxiliary electrical load of the OHE car for two hours and only lighting and fan load for five hours in case of auxiliary alternator failure Terminals sockets for charging the batteries from external charging equipment shall also be provided The location of the batteries shall be such that there is no danger of getting damaged due to tools and equipment inadvertently falling on them and battery fuse If the cells are packed in two rows in the battery box a hylam sheet shall separate the two rows The battery shall be charged by the engine driven alternator rectifier Power supply arrangement to air conditioning amp other loads The successful tenderer shall provide two DG sets noise free of 50 kVA capacity each which shall generate 415 V a c 50Hz 3 phase power supply for air conditioning lights and fans computers chart recorders printer measuring equipments UPS etc successful tenderer will have to provide a dual UPS un interrupted power supply system including maintenance free battery so that in the event of the failure of supply from diesel alternator set during the run the measurements data processing recording and display systems are not affected for at least 2 hrs and a skeleton light fan service is also available A suitable auto changeover switch between two DG sets shall be provided Requirement of air conditioning a
42. 46 Worn wheel profile 6 RDSO SK 92090 Enhanced capacity side buffer with rubber buffer spring 7 ICF EMU 2 1 01 1 Draw hook arrangement 8 ICF DMU DPC7 3 5 701 EP brake schematic diagram 9 RDSO SK 81057 Brake cylinder with slack adjuster 10 ICF EMU M 3 2 064 Bogie brake arrangement 11 RDSO SKEL 970 General arrangement pantograph AM 12 12 RDSO RDSO SK No 99003 Draw gear arrangement 13 RDSO RDSO SK No 98145 Side buffer arrangement 14 RDSO RDSO SK No 99001 Screw coupling assembly 15 ICF ICF T 0 2 514 Wheel 16 RDSO RDSO STR no 56 BD 07 For CBC 73 740 93 Effective from TI SPC OHE SPRC Annexure ll INFRASTRUCTURE REQUIREMENTS FOR MANUFACTURE 1 The OHE Car building works must be served by a Railway siding connected to a railway station or railway yard to facilitate easy movement of the stock from to the manufacturing unit if manufacturer is indigenous 2 The firm should have ISO 9001 2000 certification to cover the entire manufacturing activities Firm should have laid down Quality Assurance procedure Quality assurance plan for the product detailing following aspect should be available Organization chart Flow process chart Various parameters to maintain the control over the manufacturing Policy of disposal of rejected material and its record for documentary evidence 3 Ensure that a system exists for protection of bearing and grease drums to prevent ingress
43. 50 metal Inert Gas MIG welding equipments sets 400 600A and oxy acetylene gas welding and cutting equipment should be available h EP brake test rig i Induction heating equipment for shrink fitment of inner races on axles j Drilling and boring machines of various sizes k Adequate no of EOT cranes of suitable capacity in bogie fabrication area plate shearing amp press area underframe roof sidewall assembly amp endwall assembly area 74 Effective from 7501 93 ANNEXURE III DIAGRAM No 1D EDO T 2202 1676mm GAUGE MAXIMUM MOVING DIMENSIONS 3250 2653 265 MAX 3735 4 3135 2440 ANNE 34676 BAUGE LEVEL 305 MIN Z gt ALL DIMENSIONS ARE IN MILLIMETRES H EXCEPT WHERE OTHERWISE SHOWN 75 TI SPC OHE SPRC Effective from 3 um warrae uem soon js 7601 93 76 77of 93 Effective from n Tentative General Layout of OHE Car Annexure IV 7
44. 7 780 93 Effective from TI SPC OHE SPRC Annexure V Following data details pertaining to electrical equipment shall be submitted 1 Alternator Make and type drive arrangement one hour and continuous ratings maximum design test service speeds maximum output voltages at no load and full load maximum output current Characteristic curves details and data of windings including method of impregnation and varnish used estimated temperature rise cooling arrangement rating under natural cooling details of insulation Motorette test results evaluation criteria and test programme results of type and routine tests if conducted details of exciter and rectifier assembly details of bearings including L10 life and lubrication scheme mounting arrangement fits and clearances adopted overall dimensions and weight 2 Traction Inverter Make and type number of inverter cubicles nominal input voltage and current continuous output rating maximum phase to phase output voltage at nominal input voltage nominal output current at nominal input current maximum output frequency arrangement and details of IGBT devices Manufacturer s data sheet shall be furnished declared duty cycle rating thermal characteristics of devices and heat sinks details of cooling requirements arrangement maximum operating junction temperature of devices under worst operating conditions safety margin evaluation criteria and type test pr
45. E OF THE PANTO RDSO ELEC DTE SKEL 387 8101 93 Effective from TI SPC OHE SPRC Annexu re VII 143 6 mmm e imm THICK 360724 i D NOTE 1 ALL DIMENSIONS ARE 2 UNLESS SPECIFIED TO LERANCE OF 0 030 03 SHALL BE TAKEN ON ALL DIMENSIONS PART C amp D ADDED ON 24 5 76 MOUNTING i BAS CA 5 2 8 PARTI DESCRIPTION e cere PANTO MOUNTING INSULATOR ELEC 3870 4Nos DPILL ED HOLE 81 82of 93 Effective from Annexure VIll BRIEF DESCRIPTION OF OVERHEAD EQUIPEMENT OHE 1 0 25kV a c 50Hz single phase Traction system 1 1 A simple polygonal type overhead equipment comprising of single catenary and contact wire is automatically tensioned The catenary has 19 strands made of cadmium copper with a cross section of 65 sq mm The grooved contact wire is hard drawn electrolytic copper of 107 sq mm cross section Solid copper droppers 5 mm in diameter with a normal spacing of 9 m according to degree of curvature On straight track the contact wire is registered at the suppoets on the contact wire is registered at the supports on the contact plane by 200 mm transverse either side of the center line of track The stagger is limite
46. Hz 400 mA 1700 50 Hz 300 mA 2000 50 Hz 300 mA 2300 50 Hz 300 mA 2600 50 Hz 300 mA 5100 50 Hz 100 mA Emission from OHE Car to outside world shall be limited to level specified under CENELEC standard 50121 2 The tenderer shall submit the simulated values of these interference currents in their offer SPACE AND WEIGHT REQUIREMENTS All the equipment offered shall fit within the space available in various sections of the OHE Car The total weight of all the equipment offered shall preferably be selected so that it may not exceed the axle load The tenderer shall furnish the breakup of weight of various components equipment of the system DIESEL ENGINE The OHE car shall be powered by suitable capacity of proven make Cummins or equivalent or better fuel efficient diesel engine capable of fulfilling the requirement of specification The diesel engine shall work satisfactorily with fuel oil to Indian Standard Specification No 1460 2005 Filters for engine air intake shall be provided with restriction indicator to ensure satisfactory performance under dusty environment 48 490 93 Effective from TI SPC OHE SPRC 5 4 5 5 5 6 5 7 5 8 5 9 5 10 6 2 6 3 6 4 6 5 6 6 tenderer shall submit notch wise Engine rpm and power The tenderer shall be responsible for ensuring proper alignment of engine and transmission Air intake with filters ducts and
47. ING AND PACKING Each equipment shall bear for identification Railways order number batch lot number serial number type year of manufacture manufacturer s name as well as important nominal and short time ratings All equipment of the complete system shall be suitably packed in strong waterproof boxes to prevent any damage during transit and handling INFRINGEMENT OF PATENT RIGHTS Indian Railway shall not be responsible for infringement of patent rights arising due to similarity in design manufacturing process components used in design development and manufacturing of complete system and any other factor which may cause such dispute The responsibility to settle any issue lies with the manufacturer CONTROLS AND GAUGES Adequate control equipment including gauges instruments and cab safety devices shall be provided for safe and satisfactory operation of the car The arrangement of Driver s cab shall be as per ICF drawing No DMU DPOC 9 0 506 gauges shall be of proven and reliable design Graduations of all gauges shall be in metric units Following gauges shall be provided in the cab Local engine starting switch push button Battery charging discharging ammeter Local engine stop switch push button RPM meter Diesel engine lube oil pressure gauge Cooling water temperature gauge Electronic Fuel oil pressure gauge Traction motor load Ammeter Air brake gauges Battery charge and discharge ammeter Water level indic
48. PERFORMANCE REQUIREMENTS The performance of coach shall be adjudged as per IR standing criteria for coaching stock given as under The value of acceleration recorded as near as possible to the bogie center pivot shall be limited to 0 30g both in vertical and lateral direction A peak value upto 0 35 g be permitted provided the records do not indicate a resonant tendency in the region of peak values Sperling s Ride Index shall not be greater than 4 0 The formulae for calculating Sperling s Ride Index is given below RIDE INDEX 0 896 V b3 f o f Where b mean acceleration in cm sec f 2 frequency in Hz o f a correction factor allowing for the effect of frequencies and in Vertical Mode Lateral Mode for f 0 5 Hz 0 for f 0 5 Hz 0 325f for 0 5 lt f lt 5 4Hz 0 8f for 0 5 lt f lt 5 4Hz 400 f for 5 4 f 20Hz 650 f for 5 4 f 20Hz 1 for f 2 20Hz 1 for f gt 20Hz A general indication of stable riding characteristic as evidenced by the movement of bogies on straight and curve track and by acceleration reading and instantaneous wheel load variations spring deflections NOISE PARAMETERS The OHE Car and measuring equipments shall be so designed and built that specified noise level is not exceeded The equipment design and their mounting arrangement shall ensure the generation of noise and vibration to bare minimum The design of the vehicle shall have adequate attenuation of air borne and structura
49. TH GF INDIFISCAL a 1 PIECE SHALL HE 216 2I AND 518 WITH TOLERANCE OF 2MM FART DESCHIFTIOX TIGHTENING FOE PART 432 KG M TEM SHALL HAYE FIRST hE PLAY TO AV CIDE BREAKAGE OB STRIP DUR TO VIEW AT A A ASSEMBLY DRAWING FOR TU METALLISED CARBON STRIP CS DIRE SKEL 3O03 Rev 5 RDSO ELECT DTE 93 Effective from
50. action of contact wire and pantograph alongwith the fitment of load cell accelerometers transducers sensors instruments etc as required for the purpose Cupboards shall be provided for storage of catalogues and spare parts items equipments required to make the OHE recording car 8of 93 Effective from TI SPC OHE SPRC 6 1 6 2 7 1 7 2 7 3 8 1 8 2 fully operational to measure and record the proposed OHE parameters will fall under the scope of supply of the successful tenderer whether specifically mentioned or not This includes final testing of the entire system including the commissioning trials over Indian Railway Track to check the overall efficacy of the system with desired precision accuracy CONTRACTUAL TERMS To facilitate the examination of tender offer the tenderer is required to offer comments clause by clause of this specification either confirming the acceptance of the clause and elaborating each details where necessary or indicating deviations there from A comprehensive specification of the offered OHE Car covering functional description of the complete system salient features and advantages of the offered system details of technical support and training offered shall also be submitted along with the above comments The contractor shall be entirely responsible for the execution of the contract strictly in accordance with the terms and conditions of the specification notwi
51. aft gear box battery set amp brake equipment etc Water Proofing The OHE car shall be made completely waterproof to prevent entry of water due to rain or washing etc Observation Dome An observation dome ergonomically designed with adjustable cushioned seat for two persons shall be provided to observe the dynamic interaction between contact wire and pantograph The observation dome shall be provided with a suitable transparent material to enable a clear view of OHE pantograph interaction to be seen by the operator sitting in the dome The dome panel shall house necessary controls of pantograph raising lowering roof floodlights dome wipers video camera control communication set event marker folding 25 26of 93 Effective from TI SPC OHE SPRC 3 3 3 3 1 3 3 2 3 4 3 4 1 3 5 3 5 1 3 5 2 3 6 3 6 1 table to take notes microphone for recording commentary etc The dome shall have a reading light and fan for use of the dome operator Pantograph Two pantographs one of which shall be an AM 12 Stone Faiveley pantograph to Drg No SKEL 970 Annexure lll and the other direct air raised pantograph for high speed passenger electric locomotives conforming to RDSO specification RDSO 2009 EL SPEC 0092 Rev 0 This specification may be obtained on payment from Elect Directorate of RDSO Lucknow shall be supplied The OHE car manufactured by successful tenderer sha
52. air conditioned instrument room and other identical area like observation dome and staff officer s cabin including adequate lights and fans shall be provided Provision shall be made for keeping computers UPS with batteries other accessories necessary for recording and generating reports with adequate power supply points at convenient locations as per approved layout Provision shall be made for observation dome with comfortable sitting arrangement to view interaction of contact wire and pantograph alongwith the fitment of load cell accelerometers transducers sensors instruments etc as required for the purpose Cupboards shall be provided for storage of catalogues and spare parts All items equipments required to make the OHE recording car fully operational to measure and record the proposed OHE parameters will fall under the scope of supply of the successful tenderer whether specifically mentioned or not This 93 Effective from TI SPC OHE SPRC 2 9 2 10 2 11 2 12 3 0 3 1 3 2 4 1 4 2 includes final testing of the entire system including the commissioning trials over Indian Railway Track to check the overall efficacy of the system with desired precision accuracy The measuring equipment and associated electronic interface shall be fit for measuring OHE parameters with car running at speeds up to 105 kmph with its own power and up to 130 kmph when coupled to a train If there be any
53. al fiber based communication system be provided between Vehicle Control Computer and Traction Inverter Control system Preferably dual redundant optical fiber communication link with adequate redundancy shall be provided to improve the reliability of the system The CPU shall consist of a 32 bit micro controller running at minimum 40MHz along with its programmed software various peripheral and interface circuits e g Real Time Clock Non Volatile Memory etc All other circuits that are meant for processing either input or output signals shall be controlled through commands from this card The CPU shall continuously monitor all the inputs and control all the outputs of the system based on the software program Provision shall be made to configure the control system through Laptop for using the system with different types of traction equipment OHE Car through user programmable parameters loaded in Non Volatile Memory of CPU The details shall be finalized in consultation with RDSO A removal type of non volatile memory module shall be provided for storing the Event Data This data shall be logged during running of the OHE Car This memory module shall be prevented from unauthorized access by a Lock and Key arrangement The details of the data to be stored shall be finalized in consultation with RDSO GENERAL REQUIREMENTS OF CONTROL EQUIIPMENT The system design shall be made modular in construction to the extent possible with provision of visual in
54. asured parameter using GPS b Two week 10 working days in handling of other electronic instruments systems sub systems of the OHE car SERVICE ENGINEERING The contractor shall provide at his own expense the services of competent engineers during the guarantee period and also during the first major overhaul the OHE Car The service engineers shall be available for testing commissioning of the OHE Car training of operating and maintenance staff The service engineers shall also advise the Railways on maintenance testing and operating facilities considered necessary for efficient performance of the Car The contractor shall submit list of equipment and facilities required for maintenance and overhaul of OHE Car offered Special Tools for Maintenance The Bidder will also offer separately special jigs tools and instruments which shall be essentially required for maintenance of mechanical electrical electronics and pneumatic equipment Essential equipment and facilities required for attending local damage to the stainless steel structure and coach interiors etc in case of accidental damages shall also 16of 93 Effective from 20 5 21 22 22 1 22 2 22 3 22 4 23 23 1 23 2 be furnished The Bidder shall explain the purpose justification of the specialized equipment so offered Bidder shall submit the lists of such tools instruments jigs etc
55. asurement and 3 10 4 3 11 recording of OHE parameters as mentioned in this specification up to OHE car speed of 105 kmph when running with its own power and 130 kmph when coupled to a high speed train In case the performance of any equipment system sub system instruments transducers does not meet the requirements laid down in the specification the successful tenderer shall set right or replace the defective rejected components system within a reasonable time specified by purchaser The acceptance of the system shall not be delayed for minor defect which is not affecting full utilization of the car Such minor defects have to be set right by the tenderer within a mutually agreed time frame Working Environment The OHE recording car including the power supply equipments shall be in continuous operation under the following atmospheric and climatic conditions The car should be suitable to perform satisfactorily in J amp K area also 1 Atmospheric Metallic surface temperature under Sun 75 C max temperature and in shade 55 max Minimum temperature 10 Also snow fall in certain areas during winter season 2 Humidity 10096 saturation during rainy season 3 Reference site i Ambient Temp 50 conditions ii Humidity 10096 Altitude 1000 m above mean sea level iv Altitude 2000 m in J amp K area 4 Rain fall Very heavy in certain areas 5 Atmosphere Extremely dusty and deser
56. at each notch Maximum permissible fuel rack in relation to boost air pressure Over speed trip setting Governor response Load control timing from max to min position and from min to max position PID parameters Provision shall be made for the following safety features devices the governor being offered 59of 93 Effective from TI SPC OHE SPRC gt Low lube oil pressure shutdown gt Time delay feature A suitable time delay shall be provided in low oil pressure shutdown system at various notch speed steps to enable the engine driven lube oil pump to build up the requisite lube oil system pressure while starting the engine A manual button which would have to be reset after an LOPS shutdown has occurred must be provided gt Fail safe feature The governor shall be provided with fail safe feature so as to cause shutdown of the diesel engine by pulling the fuel racks to NO FUEL position in case of malfunctioning of the governing equipment 22 4 A Suitable display screen for status of engine parameters shall be provided The micro controller based engine governor shall provide suitable diagnostic facility to carry out trouble shooting for detecting the problematic areas locations in case of faulty operation of the governor In addition facility for fault logging system shall be provided to register fault messages with date and time stamp It shall be possi
57. ating conditions but easily removable for attention to the gear case firmly secured to prevent damage by movement and vibration under the most severe operating conditions but easily removable for attention to the gear A hole of suitable size with a plug in arrangement shall be provided to facilitate topping up of the gear compound to the correct level The motor efficiency at continuous rating shall not be less than 93 and the weight of TM should be approximately 2 tons 51 5201 93 Effective from 9 10 9 1 10 10 10 2 10 3 11 12 12 1 12 2 12 3 12 4 Gear case The gear case shall be of sturdy and lightweight construction and shall be adequately supported through the traction motor frame to prevent dropping down under the most severe vibration that may be generated due to adverse track conditions Traction Gears Traction gears and pinion shall be of proven design and to give required performance capability INSULATION SYSTEM FOR TRACTION MACHINES The insulation scheme for various electrical machines offered should be class 200 or better The machine shall be designed such that the hot spot temperature under any condition of loading in stator winding does not exceed the average temperature of that winding measured by resistance method by more than 15 deg C The manufacturer shall provide maximum possible margin in temperatur
58. ator Electronic Speed indicator cum recorder The following audio visual signals or reference panel lights shall be provided in the cab for single and multiple operation of the Power cars 60 6101 93 Effective from 29 29 1 Low lubricating oil pressure Radiator water temperature too high Cranking contactor welding indication Traction control supply ON Rectifier fuse failure Rectifier cooling fan failure Aux alternator failure Motor overload failure Motor earth fault Parking brake applied Drive function released Common annunciation Train parting indication Multiple operation status The following safety devices inter alias shall be provided e Water temperature too high Transmission cut off and engine will return to idle e Low water in radiator Power to transmission cut off and engine shut down e Low lube oil pressure Power to transmission cut off and engine shut down e Engine speed too high Over speed trip Power to transmission cut off and engine To shut down Adequate protection of an approved design shall be provided against electrical overloads and grounding The following minimum operating controls for multiple unit operation of OHE Car from any of Driver s cab shall be provided e Notch control e Brakes e Forward and reverse movement control Safety interlock shall be provided to prevent Power cars in MU operation fro
59. ble to easily retrieve the fault messages on a laptop PC based computer 23 TORSIONAL VIBRATION ANALYSIS 23 1 After placement of order the manufacturer shall furnish complete relevant data and dynamic system details pertaining to proposed traction alternator auxiliary generator required for carrying out torsional vibration calculations The manufacturer shall also furnish complete set of dimensional drawings required for the calculation of mass elastic data i e mass moment of inertia stiffness of different shafting etc Material specification and the permissible vibra tory stress values of different shaft sections of the proposed system shall also be indicated by the manufacturer Dynamic system details of the diesel engine and other auxiliary attachment of OHE Car will be supplied by RDSO to the manufacturer to assist them in deciding the dynamic system details by some approximate analysis The details indicated here shall be submitted by the manufacturer to RDSO well in advance of the actual manufacture for scrutiny and approval 23 2 Verification of torsional matching of the equipment offered with other equipment shall be done 23 3 24 by RDSO by carrying out detailed torsional vibration analysis The manufacturer shall be prepared to carry out modifications in the design of offered equipment if considered necessary from the torsional matching considerations Guarantee The supplier shall at his expense replace any part of
60. ce is not adversely affected BRAKE SYSTEM OHE Car shall be equipped with self lapping Electro pneumatic brakes of approved design and shall fulfill the requirements as given in following clauses The suppliers shall supply the detailed drawings specifications and testing procedure for rubber components valves and cocks used in the brake system and shall guarantee satisfactory working of the system and components for at least 36 months from date of delivery or 24 months from date of commissioning whichever is earlier EP brake schematic diagram for OHE Car shall be as ICF drawing No DMU DPC 3 5 701 with latest alteration Sintered bronze filter elements shall be used for pipeline filter and T type strainers The component units of this brake system shall meet the following requirements Brake Cylinder Car shall have 8 nos of 8 3 3 4 brake cylinder with in built slack adjuster and with hand brake trunion The stroke length at which the slack adjuster starts functioning shall be as per RDSO Sketch 81057 alt 9 The brake cylinders shall be as per RDSO spec No C K013 Bogie brake arrangement of OHE Car shall be as per ICF drawing No EMU M 3 2 064 with latest alteration The brake rigging shall be capable of easy adjustment to cater for maximum tyre wears of 38 mm on radius of wheels No adjustment on the brake rigging between successive renewals of brake blocks shall be necessary There shall be no obstruction to move
61. ceeds a pre set value An alternative proven and reliable protection system may also be offered by the tenderers giving full justification of the offered scheme The proposed traction inverter system shall be capable of withstanding dielectric test voltages as per IEC 61287 1 for power circuit and 60571 1 control circuit The traction inverter system shall be designed for following protection class a For phase modules IP20 b For electronic compartments IP54 53 540 93 Effective from TI SPC OHE SPRC 13 7 13 8 The main power semiconductor device used for switching shall be Insulated Gate Bipolar Transistor IGBT with sufficient PIV rating The IGBT module may contain external or internal protection circuits and gate drive circuits The complete system shall be designed as simple as possible with reduced number of components without compromising reliability and efficiency The devices offered should be field proven The detailed characteristics of the devices along with details of gate drive circuits and protection circuits used shall be furnished in the offer Suitable temperature sensors shall be provided so that temperature of phase modules IGBT modules can be continuously monitored by the control system In case of over temperature traction motor torque should be gradually reduced to keep phase modules IGBT modules at safe operating conditions Additionally IGBT modules sho
62. chedules For better appreciation of scope of work covered under each schedule the tenderers are required to give brief explanation against each item of schedule in separate sheet It should be kept in mind that provisions of shall necessarily cover the total requirement of equipment instrumentation to make the OHE recording cum test car fully functional as per the requirement of this specification However if he feels that further elaboration may be needed the same can be given in the separate sheet with brief explanation for better appreciation SECHUDELE A OHE recording car with power equipments with diesel electric transmission SN Item Description Qty Unit Total Remark Rate 1 Manufacture supply amp commissioning of 1 OHE recording car 2 Supply of 50 kVA DG sets with associated 2 accessories amp equipment 3 Supply of 5 UPS along with suitable 2 battery backup of 1 hours 4 Supply of adequate hp capacity engines 2 5 Supply of traction motors with gear and 4 pinion 6 Traction alternator along with 1 set power rectifier In case of electrical transmission system 7 Motorised bogie Powered Bogie complete 1 with Brake gear without traction motors Set 8 Battery charger for charging of starter 1 batteries unit 70 71of 93 Effective from 9 S
63. cilitate filing of drawings in RDSO it is essential that each drawing prepared for the manufacture operation maintenance shall be marked so that it can be identified The contractor shall therefore ensure that all prints submitted are marked legibly at the right hand bottom corner The following information is required in respect of each drawing submitted Contractor s drawing Number 2 Contractor s name and date of submission Contract Number 100 93 Effective from TI SPC OHE SPRC 8 5 8 6 8 7 10 10 1 10 2 10 3 11 11 3 4 Nomenclature of the OHE Car 5 Description The Supplier shall submit the complete material technical specification of the components within 45 days of design approval The specification shall specifically be indicated on relevant drawings documents The Supplier shall be responsible for carrying out improvements and modifications as may be considered necessary after tests and trials at his own expense on all the equipment supplied provided such modifications improvements are decided to be necessary for meeting the specified requirements of reliability performance safety etc jointly between Supplier and RDSO For the purpose of technical decisions on improvements modifications etc on equipment the final authority from the purchaser s side will be RDSO QUALITY ASSURANCE PLAN QAP The tenderer should have valid 1 0 9001 2008 certificate
64. cturer considers to be the maximum torque that should be used for rail traction The curve of fuel consumption for no load running commencing from the minimum idling speed expressed in kg h 1 2 Air compressor 1 3 gt ON Sao gt Maximum pressure Capacity at idle amp full speed of engine Installation drawing showing overall dimensions Weight dry full supply Cooling Graph showing speed Vs horse power amp capacity uxiliary Alternator Make Model Continuous short time rating with details of voltage and current regulation Installation drawing showing overall dimensions Weight 1 4 Traction Motors NOOO POM Make Type Maximum input hp Complete characteristic curves Continuous short time rating with details of voltage and current regulation Installation drawing showing overall dimensions Weight 88 8901 93 Effective from 1 5 Reversing Arrangement 1 Method of reversing with full details 1 6 Axle Drive Gear and pinion 1 Type of gearing 2 Module 3 Grade of steel used for pinions and gears 4 Particulars of heat treatment 5 Kilometerage guarantee for bull gears 6 Kilometerage guarantee for pinions 7 Material and type of construction for gear case 1 7 Traction Alternator 1 Make 2 Model 3 Continuous short time rating with details of voltage and current regulati
65. d be carried out in traction alternator only Any changes in the mounting design should be approved by RDSO Installation drawing of radiator fan assembly for both cooling and ventilation 50 510 93 Effective from TI SPC OHE SPRC 8 3 8 4 The main terminal box shall be mounted at suitable location such that connection disconnection can be made easily The neutral connection shall preferably be available for ground fault detection if required The alternator shall be designed for a high voltage low current operation such that the alternator voltage at rated engine output is sufficient for proper operation of the system 8 5 The alternator efficiency with rated output shall not be less than 96 The efficiency curve for 8 7 the alternator over the entire speed range shall be furnished The alternator shall be designed such that its output when rectified by a three phase bridge rectifier does not result in a ripple factor more than 5 The weight of the alternator should be approximately 3 tons 9 TRACTION MOTOR 9 1 A suitable traction motor matching with the entire system shall be offered The traction motor shall be of AC 3 phase squirrel cage asynchronous type It should have a three phase stator winding suitable for voltage of wide frequency range from inverter 9 2 The traction motor shall be self ventilated type with axle hung nose suspension arrangement 9 3 9 4 9 5 9 6
66. d in all cases complete and adequate fusion with the base material shall be ensured The side wall and end wall sheet are welded with spot welding 110 93 Effective from 11 4 11 8 12 12 1 12 2 12 3 13 13 1 13 2 13 3 The welding procedure adopted for building the body shall be of international class and no weld spots etc should be visible Welding shall cause minimum surface indentation shall not cause permanent discolouration and shall be arranged in uniform pattern Detailed weld procedure shall be submitted Welding shall be used to assemble the car body structure Resistance welding shall be used for attaching the sheath to the frame Stiffeners shall be attached to the sheathing by resistance welding The remainder of the car body structure shall be constructed by fusion welding or resistance welding All weld patterns shall be identical on all cars Resistance welding may be used for attaching the hangers and brackets to OHE car frame sub assembly Brackets supports pipe hangers conduit supports and other attachments which are not part of the car body structure may be attached to the structure with mechanical fasteners Suitable reinforcement of the car framing members in subassembly shall be done to accept attachments during assembly As far as possible the holes for attachments shall be in the webs of framing members rather than in the fla
67. d in applications where the fastener is subjected to alternating transverse loads In other cases the coarse series of threads shall generally be used except where precluded by size The use of studs shall be avoided wherever possible Socket head cap screws shall preferably be used at all possible locations 12of 93 Effective from 13 4 13 5 13 6 13 7 13 8 13 9 13 10 13 11 14 14 1 14 2 14 2 1 14 2 2 14 2 3 14 2 4 14 3 Fixings shall be locked adequately to prevent loosening in service Fixings shall withstand any shock loads the equipment is likely to encounter In critical areas the locking of all nuts bolts and fixings shall be of a positive form which prevents mechanical rotation of the nut relative to the bolt irrespective of source vibration Stainless steel parts shall be attached by stainless steel screws or fasteners except in location where high tensile strength is needed Whenever possible tapped holes shall be drilled and tapped to the full thickness of the material Blind holes shall be used only where this is unavoidable All such blind holes shall provide at least 3mm clearance between the end of the screws and the bottom of the tapped hole Tapped holes shall be provided with suitable thread inserts where necessary and shall always be used in aluminium or copper Fixings for covers which may have to be removed for
68. d to 300 mm on curves At overlaps stagger may go upto 650 mm On secondary lines regulated tramway type construction consisting of contact wire only tensioned at 1200 kgf with bridle wire provided at support points to reduce sag is used 1 2 Normal vertical and lateral electrical clearance of 320 mm has been adopted with passing clearances i e of short time duration of 270 mm and 220 mm respectively as per chapter V A of Schedule of dimensions BG The normal height of the contact wire above the rail level is 5 50 m but at loco sheds and inspection pits the height is kept as 5 8 m On critical locations such as tunnels road over bridges the contact wire height is kept as low as 4 65 m minimum Any change in the height of the contact wire is made gradually and the maximum gradient does not normally exceed 3 mm m on main lines and the 10 mm m elsewhere The variation of gradient on adjacent spans is not more than 1 5 mm m for main lines and 5 mm m on secondary tracks The vertical distance between the catenary and the contact wire called encumbrance is 1 4 m at support and is maintained except at turnouts overlaps and near overline structures and tunnels where it is suitably reduced The distance from the center of the track to the nearest face of an overhead equipment support mast is normally 2 50 m on straight track This distance is increased by necessary curve allowance on the curves This distance is also more than the normal 2 5 m
69. ded at the car body ends The car manufacturer before undertaking manufacture should make 3 D model drawings on Unigraphics CAD software version NX 4 and submit them for approval of the interior furnishing scheme After approval of 3 D model drawings mock up of vehicle with interior furnishing shall be prepared and got approved by RDSO by the manufacturer before taking up manufacturing BOGIE Bogie suspension design shall be coil steel suspension in primary and air suspension in secondary stages The bogie general arrangement shall be as per ICF Drawing No DMU DPC 0 0 502 with latest alteration for Car The bogie frame shall be of copper bearing steel plates to IS 2062 Fe 410 Cu WC and shall be fabricated by welding The pneumatic suspension system for the secondary stage of OHE Car shall conform to RDSO Specification No C K106 for air spring assembly and 407 for their control equipment The air spring shall have one vertical and one lateral shock absorber and one lateral rubber bump stop per air spring at the side of bogie The primary suspension of OHE Car shall consist of helical springs to ICF drawing No EMU M 0 1 024 with latest alteration The material of helical springs shall be as per RDSO Specification No WD 01 HLS 94 Rev 2 with latest amendment Shock absorber shall be as per RDSO specification No C 8703 with latest revision RUNNING GEAR wheel and axle shall be as per ICF drawing no DMU DPC 0 2 504 with lat
70. dications by means of LEDs for easy trouble shooting by maintenance staff 56 5701 93 Effective from 18 19 20 e Various cards used in the design shall have polarized connections to prevent inadvertent insertion into wrong slot and possible damage resulting due to this The system hardware design shall have provision to carry out self diagnostics at Driver s Instruction and at Power ON The Electronic components used shall be of Industrial Grade shall be preferable to have the entire control system hardware so optimized that the component count is kept as low as possible without sacrificing the overall system performance and reliability Password protection shall be provided for configurable parameters Voltage Current Temperature Pressure Speed etc parameters shall be monitored through sensors of adequate rating The sensors used in the system shall be provided wherever necessary with regulated power supplies e Sensors used in the system shall be based on the latest technology prevalent for the Rolling Stock application in the world All electronic equipment shall be housed in dust proof enclosures either by providing the complete equipment in dust proof cabinets and or pressuring the cabinets FUNCTIONAL REQUIREMENTS The major functions of the proposed Vehicle Control Computer shall be Engine Control through Governor Propulsion Con
71. e instrumentation of OHE recording car should be capable of performing satisfactorily upto the following maximum temperatures metallic surface temperature under Sun 75 C max and in shade 55 C max The roof mounted equipments should therefore be capable to perform satisfactorily under such a high metallic surface temperature The system and instrumentation offered shall be of such design and manufacture which have proved satisfactory performance in the tropical climate similar to that of India Past credentials should be furnished Lavatories The car will have two lavatories equipped with Indian style European type seat wash basin mirror with shelf geyser towel rail coat hooks and metallic deodorant container etc The scale of fitting shall be provided approved by the purchaser Necessary water connection shall be made from the roof water tank Water Tank Water tank of not less than 450 litres capacity shall be provided The tank shall be mounted so as to be readily removable for repairs Side filling arrangement only shall be provided for filling water Location of the tank shall be decided mutually with purchaser and successful tenderer 31 32of 93 Effective from TI SPC OHE SPRC 1 1 PART Il OPERATING AND SERVICE CONDITIONS GENERAL The OHE Car shall be a self propelled bogie type lightweight 8 wheeler rail passenger vehicle Each OHE Car shall have driving cab at both end of the car
72. e interiors of the car body such that no moisture can penetrate Gaps between all interior lining panels seat shell etc shall be minimized The effects of the thermal expansion shall be taken into account and all unsealed gaps shall not exceed 1mm in depth where feasible Suitable cushioning at panel joints shall be provided to suppress noise All the joints of interior panels and flooring shall be so sealed that there are no cavities or spaces where insects such as cockroaches etc can hide and breed Materials used shall comply with the relevant UIC specifications Where UIC specifications do not exist the contractor shall submit relevant specification for proposed material for 40 4101 93 Effective from 12 8 12 9 12 10 12 11 13 13 1 13 2 13 3 13 4 14 14 1 14 2 15 16 approval The contractor shall submit the test procedure of proposed material for approval Materials and substances classified as prohibited and restricted shall not be used The berth covering should be stain resistant easily cleanable fire retardant material in pleasing colour and pattern The cushioning material should also be fire retardant Material should be in use in passenger cars in UIC railways The berth covering should give a service life of at least six years Equipment cupboard for housing equipment for which access from the Car is necessary may be provi
73. e rise for prolonged life of the traction machines after taking into consideration the system of insulation adopted and environmental conditions prevailing on Indian Railways AUXILIARY MACHINES DRIVE Auxiliary machines drive shall be similar to the existing 1400 HP DEMU as detailed below Traction Engine cooling Hydrostatic drive Engine room ventilation Hyarostatic drive Compressor drive Auxiliary alternator drive for controls and light fan etc Auxiliary alternator Engine mounted belt driven for starter battery charging POWER RECTIFIER The power rectifier shall be 3 phase bridge using silicon diodes suitable for rectifying the 3 phase AC output of traction alternator throughout the range of operation of the alternator More than one bridge units may be connected in parallel depending upon requirement Proposed rectifier shall have sufficient margin in continuous short time ratings and surge withstanding capability Also it shall have adequate margin to withstand internal short circuits due to string failure condition and short circuit across DC link The tenderer in the offer shall indicate cooling air requirement for the rectifier The devices used in the rectifier assembly shall preferably be of a standard type of a reputed make such that in case of urgency the purchaser can interchange these devices with commercially available devices of another make The layout of components
74. eel 102 mm 7 Maximum height above rail level for centers of buffers for unloaded vehicle 1105 mm 8 Wheel Diameter New 1000 mm 9 Minimum radius of curve Horizontal 175 m Vertical 4000 m for A route 3000 m for B route 2500 m for C D amp E routes Note OHE car shall meet the requirements of IRSOD Revised 2004 which is to be confirmed at the time of conducting detailed oscillation trial 84 8501 93 Effective from TECHNICAL DETAILS EXISTING TRACK INDIAN RAILWAYS version cord of 7 2 m S N Description Details 1 Gauge Broad gauge system of the Indian Railways 1676 mm 2 Track Structure Minimum standard of 90 R rails on sleepers to 4 density and 200 mm depth of ballast cushion below sleepers which may consist of at least 75 mm clean and the rest in caked up condition On consolidation and stable formation On high speed routes 52 kg rails with 7 sleeper density have been used partly 3 Sharpest curve and 174 radius The locomotive is also checked for to be turnout negotiated passage in both direction over standard BG 1 8 2turnouts 4 Permissible tract Following are the track geometry standards for tolerance various track parameters on Indian Railways BG route as obtained from track recording cars BG High Speed BG Main Line 5 Unevenness 6 mm ge
75. eferably be of sliding type with adequate opening to facilitate the loading unloading of DG sets All door openings shall be true to specified dimensions and perfectly square The openings shall be tested for size and squareness with templates so that doors open and close freely and when closed shall be reasonably weather proof and dust proof Single leaf inward opening hinged or sliding doors with locking arrangement shall be provided in driver s 38 3901 93 Effective from 9 3 9 4 9 5 9 6 9 7 9 8 10 10 1 10 2 10 3 11 compartment and shall have a clear opening of 920 mm The door leaves shall slide roller bearing carriers suspended from top rail and shall work in retaining guides on the doorsills Each leaf shall have a window opening Since tenderer is expected to develop his own layout location of doors may be decided in the most suitable manner The door layout of the car shall be got approved by RDSO Latches shall be fitted on all doors so as to secure them from inside in the closed position Where hinged doors are provided on the side walls they shall be of inward opening type and will give an opening of 750 mm approx Rain water gutters of suitable design over the door way shall be provided Door foot steps Anti slip foot steps shall be provided at all body side doors The edges shall be protected with metallic treads A wearing
76. electrified network of IR which at present is 20059 RKM as on 31 03 2010 Indian Railways have embarked on a large scale program of the electrification To cater for increase in traffic heavier freight trains upto 9000t load are being introduced which are to be hauled with consist of one or two electric locomotives The speed of passenger trains is also being gradually increased to reach 160 km h and beyond The introduction of high speed trains as well as the increase in traffic will necessitate more frequent and accurate monitoring of OHE parameters The Self Propelled OHE parameter recording cum test is required to measure and record various parameters of OHE and pantograph in static dynamic conditions and under live and non live conditions of OHE upto a maximum speed 130 km h when coupled to a train and 105 kmph when running by its own power GENERAL REQUIREMENTS EXPLANATORY Throughout this specification the term RDSO Research Designs and Standards Organization Manak Nagar Lucknow 22601 1 is hereafter referred to as RDSO IR Indian Railways is hereafter referred to as IR Engineer Director of RDSO is hereafter referred to as Engineer IRS Indian Railway Standard is hereafter referred to as IRS IS Indian Standard is hereafter referred to as IS ICF Integral coach factory Chennai is hereafter referred to as ICF Purchaser means Railway Board on behalf of The President of Republic of India Inspecting Office
77. eleration shall also be done continuously 20 210193 Effective from i Accelerometer fitted to underside of car body Any track irregularity which can affect the vertical movement of the OHE car body and hence its effect on pantograph can thus be recorded ii Four linear sensors with differential transformers one on each spring used for measurement of compression of primary suspension The sum of four voltage outputs by sensors provides knowledge of vertical movement of bogie The tilt information is obtained by finding difference between sum of the two signals from the left side amp sum of the two signals from the right side Any other method which is more accurate and suitable to measure at higher speed of recording car may be offered If the tenderer feels that his proposed method is superior to the methods given above Tenderer have to submit the detailed procedure and justification for acceptance of the purchaser contractors design should have given satisfactory performance for a minimum period of two years on railway networks elsewhere Typical vertical acceleration values in respect of comparable vehicles have been found to be in the order of 0 320 the criterion limit however is 0 550 d lateral acceleration The measurement of body lateral acceleration may be carried out by either of the following three arrangements i Accelerometer fi
78. elsewhere RECORDING AND PRESENTATION OF TEST RESULTS All processed results shall be presented with reference to the specific mast location on the track and kilometerage It should be possible to initialize the reference kilometers by the operator at any stage All distance measurements after initializing the kilometer shall be with reference to kilometer so entered till the next initializing by operator The exact format for presentation of reports over computer monitor and plotter printer shall be mutually decided after award of the tender Such presentation may take the form of continuous display correlated with the mast location and recorded parameters and kilometric progressive over a suitable scale or may take the form of reports generated on the basis of exceedence of certain threshold values The processing software shall take care of the requirement of IR gauge and OHE for the purpose Quality of current collection During the run the number of times the contact has been lost between OHE and pantograph and the duration of such loss shall be recorded Computation shall be done for Number of time contact lost between OHE and pantograph in a kilometer of track traversed by the loco b Total duration of contact interruption between OHE and pantograph expressed as percentage of total duration of test run or measuring time in the particular section c the above measurements computation contact interruptions shall be grouped
79. eripherals display meters etc shall be provided in the instrumentation room which shall be equipped for storage of hard copies reports and other such requirements Suitable ergonomically designed good quality furniture shall be provided in the working area to meet the requirement All control cables shall be segregated from power cables and shall be suitably protected Computers Two computers with latest configuration having adequate memory capable of processing and storing information for a continuous run of at least 1 00 00 km including necessary peripheral devices inclusive of laser printer for printing of reports should be provided in the OHE recording car specification to be approved by purchaser One of the two computers shall be in network in hot standby mode such that in the event of failure of one other hot standby computer takes over the processing without loss of any measured data 26 2701 93 Effective from 3 7 3 8 3 8 1 xii xiii The OHE recording car shall be 8 wheeler vehicle The disposition of equipment and accommodation for on board staff instrument room and observation dome shall result in equal axle loads Design shall be such as to afford easy inspection and maintenance Guiding principle in selection of assemblies should be the easy availability of wearing components Provision shall be made for the following in the car Driving Cabs i
80. est alteration The wheel profile shall be to RDSO Sketch No 91146 with latest alteration EXTERIOR AND INTERIOR COLOUR SCHEME Exterior and interior colour scheme of OHE Car shall be got approved by RDSO Railway board Draw amp Buff Gear The car shall be provided with CBC transition coupling with side buffers as per Indian Railways RDSO specification No RDSO 2009 CG 22 so that car can be attached with any other stock like Rajdhani and Shatabdi express trains of IR The provision shall be made in 41 4201 93 Effective from 22 23 23 1 23 2 23 3 23 4 23 5 23 6 23 7 23 8 the OHE recording car for universal coupling arrangement with existing BG rolling stock having air brake system of Indian Railways At present Indian Railway is using draw gear arrangement to RDSO Drawing No RDSO SK 99003 side buffer arrangement to RDSO Drawing No RDSO SK 98145 and screw coupling arrangement to RDSO drawing No RDSO SK 99001 as per IRS R 10 in the coaching stock As an alternative transmission CBC coupling as per Indian Railways specification may also be provided CATTLE GUARD Cattle guard shall be provided at the driving ends of each unit The cattle guard shall have enough strength so as not to collapse on line in case of collision with stray animals like cows etc In any case damage to the system shall be minimal and it shall be ensured that the train servi
81. exhaust arrangement shall be compatible with engine system The exhaust and silencer arrangement of power equipment shall be properly routed for emission from roof The fuel tanks of 3000 litres capacity shall be provided The tenderer shall clearly spell out the emission standards of the engine being offered The engine will be equipped with eliminator filtration system for engine oil filtration This eliminator filter is a combination of self cleaning filter and disc stack centrifuge housed in a single unit which is engine mounted This eliminator system is required to give benefits like filter service at engine overhaul centrifuge service at 2000 hours for centrifuge completely sealed full flow system to reduce possible contamination with high burst pressure and continuous amp automatic back flushing system via filtered oil without assistance of external power source This eliminator system is indented to increase productivity by providing benefit of reduced filter services maintenance cost and time eliminate full flow filters and bypass disposable filters and its associated hoses and mounting parts COOLING SYSTEM The cooling equipment shall be guaranteed to work efficiently under climatic conditions specified under Clause 3 11 of chapter of Part I Apart from meeting the requirement of Diesel engine including after cooler the cooling equipment shall be required to dissipate heat of lube oil hydraulic oil used for hydrostatic fan
82. far as possible Large windows on both sides are to be provided with clear glass for better visibility 3 8 2 2 The tenderer shall also submit his own design of berth and seating plan and detailed 3 D model of seating including ergonomic designs of seats for approval of RDSO 3 8 2 3 Seats shall be ergonomically designed All seats and backrests shall be cushioned and upholstered with artificial leather The seats shall be firmly fixed to the frame which shall be robust enough to stand overload and misuse Under seat supports shall be constructed and located to allow for clearance provide easy access to the floor below the seat for cleaning and washing 3 8 2 4 The seat frames should be made of austenitic stainless steel 3 8 3 Kitchenette A kitchenette approx 1500mm x 2000mm shall be provided An exhaust fan shall be fitted on one of the windows to expel out the smokes etc from the kitchenette Windows for cross ventilation shall also be provided Kitchenette shall have provision for keeping cooking range LPG cylinder a refrigerator cooking utensils and complete dinner set 3 8 4 Communicating doors Each driving cab shall have independent entry from both sides The car lobby shall have entry from each cab Through communication inside the car shall be provided It shall be possible to isolate the cabins using sliding doors with locking arrangements 3 8 5 Safety measures Suitable safety measures including interlocks between various
83. for ease of cleaning and maintenance Provisions shall be made to prevent any squeaking rattling or drumming Items such as rubber strips and other items shall be integrated with panels as far as possible All interior panels shall be of glass fibre reinforced panels GFRP All internal GFRP surfaces shall have solid surface top paint less and be smooth finished The panels shall be resistant to water and aggressive cleaning chemicals for graffiti removal high temperatures UV light and radiant heat The panels shall be resistant against kicks punches and scratching No cracks shall occur Areas around fasteners shall specially be considered Exposed materials and surfaces shall withstand daily use of various cleaning agents alkaline or acid detergents petroleum solvents and mechanical action of brushes without loosing colour or noticeable deterioration of surface The panel should have a durability of at least 10 years without blistering scratch dent crack discolour lose their gloss level or any form of colour deterioration The interiors should not have visible screws allen screws The fastening devices fixings and securing screws shall not be visible from within the cars All the interior fittings shall have anti injury features should not have sharp and pointed edges Rounded corners or covings shall be provided wherever mutually perpendicular flat plane surfaces abut Metal kicking strips with radiused transitions must be provided in th
84. from the bill of the contractor Tenderer should indicate man days required for scheduled maintenance kkkkkkk 200 93 Effective from TI SPC OHE SPRC 2 1 2 2 2 3 2 4 2 5 PART I CHAPTER Il PARAMETERS TO BE MEASURED The OHE car should be able to measure and record the required parameters in the speed range 0 105 kmph when running in self propelled mode and in the speed range 0 130 kmph when coupled to a train The OHE car shall be self contained and completely equipped with all measuring recording facility and there shall be no dependence on external source The measurements shall be made under live or non live condition of the OHE during day and night The pantograph of OHE car may be fitted with instrumentation such as accelerometers transducers load cells and strain gauges etc as required but such fitment shall not materially affect the static dynamic performance of the OHE car pantograph The sensors are preferably to be installed on the roof of car and non contact measurement shall be preferred For parameters like contact wire height stagger slope and thickness dia of contact wire only contact less measurement system employing state of the art technology shall be acceptable All processed information shall be made available in the instrument recording room of the OHE car The connections from roof of the car to the instrumentation room inside the cab shall be rig
85. fter referred as Car for operation on BG section of 1676 mm gauge of Indian Railways 2 2 The scope shall also include the following Provision of all documentation and support material associated with the operation and maintenance of the cars Ongoing technical support and defects liability coverage until the completion of the warranty period and making good defects Training of engineers operations and maintenance staff including providing the training materials training kits and demonstration equipment Initial supply and installation of all consumables and materials required for testing and commissioning Provision of final drawings design calculations and other documents including operations and maintenance manuals for review and acceptance by the Purchaser s Representative Manufacture of cars in India progressively within a defined time frame and within a programmed manner 2 3 The cars should have the following features a b Good aesthetics High comfort levels Passenger amenities 50193 Effective from TI SPC OHE SPRC 2 4 2 5 2 6 2 7 2 8 d Ease of maintenance e Longer periodicity between overhauls f Low life cycle cost 9 Low weight h Flush level smooth exteriors i Use of interchangeable modular components Extensive and prominent labeling of parts k High reliability Fire and smoke detection m Use of fire retardant materials n Environme
86. ges for the use of special or proprietary fittings embodied in the construction of the coaches shall be borne by the Contractors A list of components for which royalty is paid together with the names of the firms and the royalty paid shall be furnished to the Engineers PHOTOGRAPHS Colour photographs of various assemblies and sub assemblies for newly built OHE Car shall be taken especially for the measuring equipments shell underframe power pack and body in various stages of manufacture and also for the parts which cannot conveniently be photographed after assembly such as body sidewall end wall roof framing under frame measuring equipments etc After completion side end and three quarter views of OHE Car shall be taken including views of the interior furnishings The photographs shall be not less than 380 mm x 255 mm for the side views of the complete coach or less than 255 mm x 200 mm for other views The soft copy on compact disc CD and Pen Drive and three sets of prints of each shall be furnished to the Engineers the prints being mounted on sheets to form complete set BINDINGS One set of final working drawings together with a set of photograph print out shall be suitably bound and furnished to the Engineer along with a softcopy on CD DVD media TRAINING ON VEHICLE The contractor shall provide training at the manufacturer s place for at least four persons for 15 working man days each for adequate number of Indian
87. gned to form a satisfactory chord to the superstructure considered as a girder and to take a concentrated load of 4 men standing close together at any point The structure shall consist generally of two main longitudinal members running from end to end of the car braced at frequent intervals along their lower flanges and rigidly connected to the arch bars and to the grab pillars by rigid transverse members At partition and semi bulkheads the sills shall be attached to vertical pillars within or forming part of the partitions 39 4001 93 Effective from 12 12 1 12 2 12 3 12 4 12 5 12 6 12 7 or semi bulk heads The construction through out shall be absolutely watertight and shall permit easy renewal of corroded sheets Roof Ventilators The roof ventilators of a better design shall be provided and they shall not violate the schedule of Dimensions INTERIOR FINISH amp FURNISHINGS The contractor shall propose world class vehicle interiors which incorporate a modern aesthetic approach with considerations to optimize staff comfort safety and security as well as to minimize noise in the Car The interior configuration shall be based on modular concept where the end areas of the vehicle are as like as possible XXXXX All interior surfaces must be finished with good blending and good slow ageing properties to provide a pleasant high quality interior and
88. h a laptop PC A menu driven easy to use application software shall be provided for loading on the Laptop PC for this purpose Password protection shall be provided to safeguard against misuse ENGINE GOVERNOR The tenderer shall coordinate with the engine supplier to offer a suitable micro controller based engine governor This Governor should be capable of interacting with the main vehicle control microprocessor The governor shall be suitable to provide eight engine speed steps notches the idle being 700 RPM and maximum speed is 1800 RPM It shall have provision to alter any notch speed if so required in future Micro controller based engine governor is required to maintain stable engine speed i e free from hunting at each notch position in both conditions with or without load It shall also maintain constant power output of the engine at each notch position For intermediate notch positions the time taken to adjust engine rpm shall be in the same proportion In case of engine rpm increase beyond a preset value an engine over speed trip facility shall be provided to effect engine shutdown by way of bringing fuel rack to zero Suitable Fuel Oil Pressure FOP and Lube Oil pressure LOP Transducers shall be provided The governor shall be provided with facility to adjust following parameters of the engine through software Notch wise engine speed Notch wise minimum lube oil pressure for engine shutdown Maximum permissible fuel rack
89. he equipment shall be suitably designed The equipments and their arrangement shall withstand satisfactorily the vibration and shocks normally encountered in service which are as follows a Maximum vertical acceleration 3 0g b Maximum longitudinal acceleration 5 0g c Maximum train acceleration 2 0g g being acceleration due to gravity The car and its principal assemblies shall be designed and manufactured to give satisfactory performance in the tropical climate having very dry amp dusty regions in arid zones of the country to humid coastal areas and extreme cold climate of the northern region Operation time Day amp Night Operation Duty All measuring devices installed shall be suitable for continuous working on live or non live OHE under all atmospheric conditions throughout the year Nominal system Voltage of 25kV AC single phase 50Hz Overhead contact wire Variation in Traction 19 kV to 27 5 kV sometimes touching Supply voltage kV 30 kV Maximum speed of OHE car 105 km h with its own power Maximum speed of OHE upto 200 kmph recording car when attached to train 30 3101 93 Effective from 3 15 3 16 3 17 3 18 The interior where the computers and instrumentation system and living accommodation etc are provided shall be air conditioned with maximum relative humidity of 40 6096 and average dry bulb temperature of 20 250C However th
90. hing the voltage ripple of the rectifier output and for supplying the reactive power for inverter switch over and traction motor excitation a capacitor bank of optimal value shall be provided keeping considerations of permissible ripple voltage in the intermediate circuit on one hand and the space occupied and the current to be controlled in the event of a short circuit on the other VEHICLE CONTROL SYSTEM All the digital input signals of Switches Relay Contact Feedbacks Contactor Feedback contacts etc shall be electrically isolated before being given to the Vehicle Control Computer through a Digital Input Interface All such Digital Input interfaces should be provided with reverse polarity and surge protection to prevent damage to the computer circuits against inadvertent wrong connection All driving output signals for the Relays Contactors Lamps etc shall preferably be driven through a MOSFET based circuit of adequate rating These outputs shall be electrically isolated from computer circuits and shall be provided with protection against short circuit and reverse polarity All the analog input signals that are received from the various Sensors e g Voltage Current Temperature Pressure etc shall be conditioned and electrically isolated with Isolation Amplifiers before being used by computer Similarly all the analog outputs shall be electrically isolated from CPU and shall have short circuit protection It is preferable that an optic
91. iciency with respect to OHE Car speed For semi conductor devices a safety margin of 25 on the ratings for current and voltage under worst operating conditions shall be provided and established through calculations Inverter system shall be provided with following features to minimize possibility of OHE Car being stalled on the section In case of axle unit system one axle can be cut out in the event of major faults with the inverter Similarly in case of bogie control traction motors of a bogie may be cut out in the event of an inverter fault In either case it must be ensured that OHE Car must reach to destination with defective equipment isolated Suitable margin shall be provided in the equipment rating such that under emergency conditions with isolation of single traction unit such as inverter traction motor s etc OHE Car must reach at destination on level track at reduced speeds if adhesion conditions are satisfactory The one hour ratings of the 54 55of 93 Effective from TI SPC OHE SPRC 14 5 14 6 equipment shall not be exceeded under such operations For this purpose short time ratings of the major equipment shall be furnished by the manufacturer Inverter electronics should be TCN compatible All communication interfaces should be TCN compatible as per IEC 61375 1 However if it is not possible to design TCN compatible inverter control system having proper functional interface with veh
92. icle control system then the alternative communication interface offered shall be got approved In this case the tenderer shall submit details of the alternative protocol to RDSO for approval Features of data logging for monitoring fault conditions Facility for interfacing PC laptop for upload download of data for fault diagnostics and further analysis shall be provided A real time clock unit is to be provided along with the fault logs so that tripping time can be co related with the operating conditions of the OHE Car The fault codes should be in text format which shall be comprehensible for the operating and maintenance personnel Faults should be stored in permanent memory with a buffer battery Minimum fault log size should be 50 faults with ring buffer It should be possible to download the fault log using a lap top computer and interpret it through a separate common PC application such as MS EXCEL etc Important parameters of the equipment at the time of occurrence of the fault should be recoverable for fault analysis and must include the following a Identification of the fault and its brief description in text and coded form b Identification of components and sub assemblies involved C Time and date of fault occurrence The programme download must preferably be through an online connected platform without the need to remove the memory chips A FLASH EPROM based program memory is preferred Facility for standalone
93. id enough to avoid any failure due to poor connectivity during movement of OHE recording car due to vibrations Principles methods used for the measurements as indicated in each of the following clauses are only suggestive and the successful tenderer should employ state of art technology capable of high accuracy and precision in measurement and recording All corrections compensations due to bogie body and pantograph oscillations should be built into the measurement methods for giving better accuracy precision in measurement and recording The parameters that the OHE car is required to measure and monitor are detailed as follows a Contact force Continuous measurement of the contact force between the pantograph and the contact wire which may differ from the upward force of the pantograph due to oscillations of the contact wire shall be made by suitable transducers installed on the pan of the pantograph Force sensors shall be small and lightweight so as not to affect the aerodynamic uplift and current collection property of the pantograph b Panto acceleration The vertical acceleration of pantograph as well as its vertical displacement shall be measured continuously when the OHE car is in motion The lateral acceleration as well as horizontal sway of the pantograph pan with reference to the central line of the pantograph in static condition shall also be measured continuously c Body vertical acceleration The measurement of body vertical acc
94. illers Sides mm m lt 1mm Ends mm m lt 2mm Roof radius and center part of roof mm m lt 3mm REQUIREMENTS FOR STRENGTH OF OHE CAR BODY The mechanical strength of the OHE car body structure shall comply with the requirements of UIC 566 The Carbody and any equipment mounted on beneath or within it shall be designed to withstand the fatigue loads that the car body structure will encounter in service during its design life The fatigue life assessment of body structure shall be carried out using proven standard techniques and shall be submitted by the car manufacturer for review by the IR s representative JACKING PADS There shall be a minimum of two jack pads on each side sill to facilitate safe lifting of the Car One set of jack pads shall be suitably located to permit jacking the car with IR standard floor jacks so that the bogie can be rolled from under the car without removing any equipment or structure The bottom of all jack pads shall have a non skid surface to provide frictional resistance against incidental horizontal loading between the jack pad and jack head Suitable car jacking pads should also be provided at the front end for lifting the car with the bogie in case of re railment CORROSION PROTECTION The exterior of the OHE car body shall not be painted Measures that will maintain the original appearance of the car exterior from undue deterioration staining or streaking shall be adopted The supplier may
95. ils of control strategy duly describing its merits The software of the inverter control system shall be fully compatible with the Vehicle control software including closed loop propulsion control slip slide control exchange of temperature data fault diagnosis etc The inverter system should have its own protection and control logic which it should also be able to communicate with the vehicle control software in the event of a fatal failure to initiate a protective shutdown of the OHE Car Damage to IGBT devices of the inverter shall be prevented in case of a short circuit at the load end Motor cut out facility shall be provided to isolate defective traction motor s in case of any fault In case axle control philosophy is followed each defective traction motor can be isolated individually In the event of bogie control system and in case of inverter cut out inverter control system shall be designed to automatically reduce OHE Car power adequately so that remaining inverters and motors are not overloaded and the OHE Car is able to reach up to destination with reduced power OHE Car power shall be reduced in proportion to the number of traction motors cut out at that time Inverter Protection System shall be used to protect the inverters from over voltage and over current conditions on supply as well as load side Protection shall be achieved by turning OFF the traction alternator excitation by vehicle control system in case current or voltage ex
96. imultaneously at overlaps and turnouts upto a limit of 700 mm Alternate offer should be also be submitted for simultaneous measurement of stagger of two contact wires upto 350 mm The stagger of contact wire may be measured using any non contact measurement method The accuracy of stagger measurement should be minimum 5 mm 0 Height of the contact wire The height of the contact wire is vertical distance of its underside from the rail level and it varies from 4500 mm to 7500 mm The height measurement should be corrected for car body movement Height of contact wire may be measured using any non contact measurement methodology The accuracy of height measurement should be minimum 5 mm h Measurement of contact wire thickness Thickness implies the diameter of contact wire The diameter of new 107 mm2 size contact wire is 12 24 mm and its condemning limit is 8 24 mm The measurement of diameter of contact wire may be made using any non contact measurement method The accuracy of contact wire thickness measurement should be minimum 0 2 mm for new and 0 4 mm for worn contact wire i Gradient slope of the contact wire The gradient of the contact wire is the rate of change of height expressed in mm m of distance This may be calculated based on variation in height of contact wire and distance travelled Alternately contractor s design can also be considered subject to the conditions as in 2 5a iv The accuracy of gradient slope of
97. ing the performance of the Car shall be submitted in duplicate along with the delivery of each coach Test certificates of major vendor items shall also be supplied along SERVICE CATALOGUES Detailed operating manual maintenance and service manual and driver hand book shall be specifically prepared for the OHE Car and at least 3 copies each of the same shall be supplied free of charge per OHE Car to the consignee and three copies to RDSO alon with DVD The draft contents of the manuals shall be submitted for approval to RDSO within 45 days of design approval These documents shall also be supplied on compact disc CD compatible to MS Office software The manual shall include chapters on General characteristics Technical data sheet of all the equipment offered as Annexure V All the technical details of measuring equipments and their electronic interface Technical documentation explaining complete system including characteristic curves inverter output curves and efficiency diagnostic and protection circuit etc Vehicle control system schematics Car design and its details including under frame design Details of mounting of diesel engine and inverter control traction machine etc 8 cooling system Drawing of each sub system with interface details Procedure for user settable parameter alteration fault data downloading and analysis etc Maintenance and trouble shooting manual for all the equipment offered
98. inside the rectifier assembly shall provide for easy accessibility and replacement of the failed components during maintenance without having to remove large 52 53of 93 Effective from TI SPC OHE SPRC number of other healthy components Each component shall be clearly marked to indicate type nomenclature and rating 12 5 All the components such as diodes heat sinks fuses micro switches snubber capacitors resistors etc and their mounting arrangement shall be designed to withstand vibrations and shocks as specified in IEC 60571 13 TRACTION INVERTER SYSTEM 13 1 13 2 13 3 13 4 13 5 13 6 Proposed traction inverter system may preferably have four inverters using one inverter individually for each motor Alternatively a configuration of two traction inverters may also be offered In this case each traction inverter shall drive traction motors on one bogie Input supply for all the traction inverters shall be the same DC link The basic control philosophy for the induction motor shall be such as to achieve best suited results for traction application like minimum device losses high dynamic response stable constant speed operation fast acting slip slide control etc Direct Torque Control Vector Control Slip Frequency Control etc are some of the popular control strategies used for traction drives Vector control system is used in the existing DEMUs The tenderer shall furnish the deta
99. ion Software packages along with the suitable hardware amp system support for scrutinizing the design calculations equipment ratings performance evaluation amp making simulation studies etc shall be submitted The package shall be complete in all respect so as to enable RDSO to simulate all performance and operational related variables in India RDSO The Supplier shall supply all materials cartage tackle plant spare parts special tools and appliances which may be necessary for the complete and efficient installation testing and commissioning of the new units at his own expense even if such material or work may not be specifically mentioned in this Specification The Supplier shall also arrange installation testing and commissioning of the OHE Car under his complete supervision Proposed OHE recording cum test car shall be self propelled and shall have driving cabs on either ends The space for accommodating two DG sets of 50 with sound proof compartment a well furnished air conditioned instrument room and other identical area like observation dome and staff officers cabin including adequate lights and fans shall be provided Provision shall be made for keeping computers UPS with batteries other accessories necessary for recording and generating reports with adequate power supply points at convenient locations as per approved layout Provision shall be made for observation dome with comfortable sitting arrangement to view inter
100. ise level in Driver s cab The general layout and arrangement of equipment in drivers cab shall follow UIC CODE 651 latest edition with respect to dimensions safety features furnishing lighting ventilation noise level field of view drivers desk and seats Spotlight shall be provided at suitable locations EXTERIOR NOISE LEVELS The exterior noise levels as measured on dry track shall conform to the values as under During the tests all windows and doors shall be closed and all propulsion and auxiliary equipment shall be running at maximum levels Train Stationary With OHE Car stationary and all systems operating simultaneously under normal conditions the noise level measured at a location 15m horizontally from the track centerline on a horizontal plane passing through the axle centerlines shall not exceed 65 dB A at any point along the length of the vehicle on either side Train Moving With OHE Car moving on grade with clean smooth rails at all speeds from 0 to 105 km hr and whilst accelerating or braking with all vehicle systems operating simultaneously under normal conditions the noise level measured on either side at 25 m from track centerline on a horizontal plane passing through the axle centerlines shall not exceed 80 dB FIRE PERFORMANCE The OHE Car stock shall be designed to minimize the risk of a fire starting and to prevent the fire propagation through the use of fire barriers in the floor and in walls a
101. keep them free from moistures and dust The Bidder shall furnish the protection level All equipment shall be adequately earthed insulated screened or enclosed They shall be provided with essential interlocks and keys as may be adequate to ensure the protection of the equipment and the safety of those concerned with its operation and maintenance Lubricants and cooling oils Supplier shall study the currently available lubricants cooling oils in India and employ them as far as possible Full lubrication scheme and schedule for the OHE Car shall be submitted Wherein imported lubricants or cooling oil are used Supplier shall study and furnish details of equivalent Indian lubricants oil SCOPE OF SUPPLY The OHE Car supplied shall be fit for running and measuring the OHE parameters at a speed up to 105 kmph when self propelled and 130 kmph when coupled to a train in assembled and finished condition alongwith complete documentation including design calculations and data spare parts list Maintenance Manuals Operation Manuals Training Manuals QA documentation detailed drawings and Key layout drawings it shall be self propelled with under slung power equipments with complete instrumentation for measuring and recording OHE parameters as per specification Supply of lubricants and other consumables for the initial period of 12 months of commissioning and service Supply amp installation of material required for testing commissioning and operat
102. king under 25 kV 50 Hz OHE system Electronic signals generated inside the measuring equipments traction inverters and vehicle control systems shall not be affected by this and Car with all instrumentations shall work without any adverse performance The tracks over which the offered system will work may be equipped with DC track circuits 83 1 3 Hz track circuits as well as track circuits at higher frequencies Harmonics generated by the inverter system and measuring equipments should not affect signalling gears like audio frequency track circuits and axle counters which work in the range 0 5 kHz with a limit of 400 mA On the communication network control circuits teleprinter circuits as well as VHF UHF and microwave circuits are employed The psophometric voltage induced on communication circuit running by the side of track should not exceed 1 mV The electric and electronic equipment used in the inverters and Vehicle Control System shall comply emission and immunity aspects of EMC to CENELEC standard EN 50121 3 2 The internal EMC shall cover a combination of earthing shielding and isolation of interference sources so that conducted and radiated noises are properly segregated or suppressed and no other equipment is affected due to operation of measuring equipment inverter The following interference current in the output current waveform shall not be exceeded at any point in the operating envelope of the Car Psophometric current 5 A 100
103. l borne vibrations along potential paths from the sources to passenger area and to wayside receptors The Contractor may propose car exterior and interior noise level standards better than those specified herein provided that this does not cause significant weight penalties INTERIOR NOISE LEVEL Interior noise criteria apply to measurement within an empty and stationary car with doors and windows closed Propulsion equipment noise in the passenger area The noise level shall be measured at any point along the longitudinal centerline of the OHE Car and at a height of 1200mm above the floor level The partitioning and the portion of the coach forming the engine room shall be provided with additional sound barriers to insulate the passenger compartment from the noise emanating from the equipment inside the engine room In any case the noise level measured at 1metre from the partition wall of the engine room shall not exceed 75 with coach stationary and all equipment in the engine room running 33 34of 93 Effective from 6 3 6 4 7 2 7 3 8 0 8 1 8 2 8 3 8 4 Auxiliary Equipment Noise with Car Stationary With all auxiliary equipment operating simultaneously at maximum capacity the noise level in the car shall not exceed 70 dB A at any point along the car centre line 1600 mm above the floor and not less than 600 mm from the end of the vehicle No
104. ll be constructed of lightweight high tensile austenitic stainless steel All stainless structure shall be AISI 301LN low carbon with nitrogen or SUS301L with Nitrogen or better with a brush finish Stainless steel sheathing on the sidewall shall be flat while the stainless steel sheathing on the roof may be flat or corrugated In case corrugations are provided on the roof the depth shall not be greater than 1 2 inch 12 7 mm The corrugations shall not trap moisture Underframe members shall be of corrosion resistant structural steel to IRS M 41 with body bolster to copper bearing quality steel to IS 2062 Fe 410 Cu WC of welded integral structure The selection of stainless steel shall ensure that there are no inter granular corrosion cracking and stress corrosion cracking Bidder shall confirm this with complete manufacturing and welding procedure standards adopted and proof of its sustained successful working under loaded conditions as specified The weight of the OHE Car shall be kept as low as possible consistent with adequate strength to meet the loading without exceeding stresses and deflections specified values for the structure CONSTRUCTION General The manufacturer shall ensure interchangeability of components and uniformity of structure throughout the fleet for the purpose a sufficient number of jigs fixtures and templates shall be used Such parts of the bodies as underframe side frames end frames and roofs shall be buil
105. ll be fitted with both the pantographs The roof layout and instrumentation fitment shall be so configured that it is possible to view either of the pantographs from the observation dome Appropriate switching mechanism to allow raising of only one Pantograph at a time shall be provided to preclude the possibility of both Pantographs being lifted up simultaneously Complete pneumatic circuit including compressor d c power supply etc for raising and lowering of pantograph is covered in the scope of work and has to be provided by the tenderer Battery of adequate capacity shall be supplied and installed at a suitable location to power the rooftop transducers etc The battery shall be maintenance free and preferably dry type In case charging replacement of dry battery needs switching off of traction supply of OHE either a long life battery shall be provided or a suitable arrangement shall be provided for charging the battery without resorting to switching off traction supply The tenderer shall specifically mention the charging replacement requirement in his offer Communication System Communication shall be provided between all the cabins of the car and observation dome The communication facility in observation dome should be of speak phone type to enable the personnel to speak without lifting the hand set At all other places it shall be of handset type Instrumentation Instrumentation including LED TV DVD on board computers with its p
106. m being moved when all the Power cars are not set for propulsion in the same direction SPEED INDICATOR RECORDER Speed indicating and recording equipment of 0 160 km h range shall consist of an axle box mounted opto electronic speed sensor one junction box and one recorder cum indicator unit with micro controller containing FLASH EEPROM internal memory for calculating and recording the journey data A portable FLASH memory card shall be used for external memory The equipment shall conform to RDSO specification No MP 0 3700 07 Rev 03 of April 2003 61 6201 93 Effective from 30 30 1 CABLES 8 OTHER ELECTRICAL FITTINGS Electron Beam Irradiated Power amp control cables of standard metric sizes shall be provided as per RDSO Specification No ELRS SPEC ELC 0019 Latest Terminal ends for control cables and wire shall conform to RDSO Specification No MP 0 5200 04 30 2 The OHE car shall be equipped at both ends with standard headlights to RDSO specification 30 3 30 4 30 5 31 31 1 32 32 1 33 33 1 34 34 1 35 35 1 for Twin Beam Head Light with 24 V DC halogen lamps for electric diesel electric and EMU ELRS SPEC PR 0024 Rev 1 Sept 2004 and specification for DC DC Converter for electric loco diesel electric loco No ELRS SPEC DC DC Converter 0021 Rev 1 Sept 2004 Aspect lights cab lights conduits etc shall be
107. maintenance shall be captive Items of electrical equipment shall be fitted to panels so that all fixings can be made from the front only except where specified otherwise All steel fasteners used in electrical equipment shall be either galvanised or cadmium plated INSPECTION The whole of the materials or fittings used for works covered by the specification shall be subject to inspection by the Inspecting Officer and shall be to his entire satisfaction The Inspecting Officer shall have the power to Adopt any means he may think advisable to satisfy himself that the materials or fittings specified are actually used throughout the construction Take samples for such tests as he may consider necessary by an approved metallurgist selected by him whose report shall be final and binding on the Contractors Visit at any reasonable time the Contractor s works to inspect the progress and quality of the work and the Contractor shall provide free of charge all equipment labors gauges etc required by him for this purpose To reject any material or fittings that do not conform to the relevant specification or good practice which shall be marked in a distinguishable manner and shall be disposed of in such a manner as the Inspecting Officer may direct The Contractors without extra charge shall replace such rejected parts Tests of materials and fittings shall as far as possible is carried out at the works of the makers of the materials
108. may be provided at a convenient location before the rectifier regulator panel An interlock shall be provided so that at a time either engine driven or axle driven auxiliary alternator is functional Rectifier Regulator The rectifier regulating equipment shall be under frame mounted and confirming to IEC 60571 Crimping sockets required for inter connecting and output cables shall be supplied along with the equipment The rectifier regulator box shall have an openable front cover which shall be capable of being closed and locked in position by a suitable hinged bolts and nuts It shall have protection level of IP 55 hose proof and shall be electro galvanised and painted grey The regulator shall have provision of potentiometers for currents and voltage setting for adjustment depending upon the service conditions 64of 93 Effective from TI SPC OHE SPRC 2 5 2 5 1 2 5 2 2 5 3 3 0 3 1 4 0 4 1 4 2 4 3 4 4 4 5 4 6 Starter Battery 24 V 450 Ah low maintenance Lead Acid storage batteries 5 hrs discharge rate conforming to RDSO PE SPEC TL 0001 1998 Latest and approved make shall be provided Adequate fuse protection is given in positive and negative battery circuit The battery shall cater to 3 cranking of engine at 10 seconds interval Battery for controls 110 V 120 Ah VRLA type batteries of approved make conforming to RDSO PE SPEC TL 0009
109. ment of the brake rigging at any stage of its working so as to result in sudden reduction of brake power Adequate safety straps shall be provided below the moving components of the brake rigging and other components to prevent falling on the track in the event of failure of any component All the brake rigging pins joints should be provided with bulb type cotters Strainers dirt collectors and filters shall be placed as close as possible to the equipment they serve They shall be accessible for maintenance and cleaning and shall be provided with isolating cocks which can be seen and operated easily An approved arrangement shall be provided to cool the air leaving the compressor and shall have a water collecting reservoir and drain cock Automatic Blow Down Cock is preferred in addition to automatic drain valve 42 43of 93 Effective from 23 9 23 10 24 24 1 24 2 25 25 1 25 2 25 3 25 4 26 26 1 26 2 27 27 1 Twin tower heatless regenerative type air dryers to RDSO Specification No MP 0 01 00 09 Rev 01 May 2005 shall be provided to supply dry and clear air to the electro pneumatic Pneumatic equipment and air springs to avoid condensation of the moisture in the system Application of any type of brake shall result in simultaneous cutting off of the power to the driving axles Parking Brake Spring applied parking brake arrangement
110. ment of various brake system parameters like initial charging time application time release time etc The running trials shall consist of measurement of braking distances under different operating conditions in both tare and loaded mode The test scheme for these trials shall be finalized at the design stage Tests on Parking Brakes The parking brake will be tested as follows The complete OHE Car under tare condition will be brought to stop on 1 in 100 gradient by application of air brake The parking brakes of the Car will be applied fully and the air brakes released Under these conditions the parking brakes shall be capable of holding the Car stationary on the gradient Test results shall be recorded for wet rail conditions The Dynamometer car tests shall be conducted on the OHE Car to ascertain starting and rolling resistance of the cars and to prove tractive effort versus speed characteristics and dynamic braking effort versus speed characteristics of the car The detailed test scheme shall be finalized during design stage 69 7001 93 Effective from PART VII SECHDULE OF QUANTITIES 1 0 The tenderer shall quote as per the following schedules of quantities Each schedule shall be quoted separately and the cost against the items of each schedule shall also be kept as separate Tenderer shall keep the description of the items same as mentioned in the s
111. ments to improve the specification at the earliest This car shall be employed on the Indian Railway to record OHE parameters of electric traction under live condition of OHE charged at 25 kV ac User railways may also give their comments All the comments may reach this office to Executive Director TI by 15 April 2011 mail ID is edti2010 gmail com 3of 93 Effective from TI SPC OHE SPRC PART 1 FOREWARD 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 On 25 a c electrified routes different types of overhead equipment OHE have been provided ranging from fixed type un regulated OHE without articulation to the present auto tensioned sagged regulated OHE In and around Mumbai area 1500 V d c traction system also exists which is under conversion to 25 kV a c system However the dynamic behaviour of different types of OHEs with regard to current collection at different speeds has not been evaluated both qualitatively and quantitatively Various parameters like height stagger wear of the contact wire condition of OHE at the crossovers are at present measured checked manually and or with the one available NETRA car which is time consuming Current collection performance is monitored by noticing the sparks at night and or through OLIVER G equipment These methods suffer from errors in measurements and individual judgment The single NETRA car available with IR is not adequate to scan the entire
112. mplete OHE Car shall be loaded to test load conditions specified in UIC 566 and run on curved track having a angle of 10 with no gauge widening when the following conditions should obtain There shall be no fouling of parts due to the throw over of the bogies and due to the movement of the coupling gear between the coaches While the unit is on this curve the brakes shall work efficiently and reliably Tests on OHE Car at site To ensure that the brake and control equipment are reliable and efficient when operated from the driving compartments at each end of Car it will run in service to testing OSCILLATION TRIALS The Oscillation Trials shall be conducted on the Car to assess its riding and stability characteristics The Trials shall be conducted in India in association with the contractor The trials shall be conducted upto a maximum speed of 115 Km h on level tangent track e and loaded condition e With new and worn wheel profile The trials shall be conducted on selected test stretches consisting of straight station yard and curve sections Braking Distance trials The Braking Distance trials shall be conducted on the Car decided during detailed design stage 68 690 93 Effective from TI SPC OHE SPRC 2 5 2 2 5 3 2 5 4 2 5 5 2 6 2 6 1 2 6 2 The trials shall consist of Stationary Trials Running Trials The Stationery Trials shall consist of measure
113. neral and 10 15 mm mm at isolated spots 6 Twist 2 0 mm m with Isolated 3 5 mm m spots of 3 5mm m 7 Gauge Variation 6mm 6 3mm 8 Alignment 5 mm in general with 7mm isolated 7 mm on curves and 10mm on straight 85 8601 93 Effective from Particulars to be supplied for respect of OHE recording cum test car alongwith the tender offer The following data shall be supplied for the car with the tender offer mm 1 2 3 4 10 11 12 14 15 16 18 19 Length of the car overhead stock Total wheel rigid base Height of car floor under tare Distance between bogie centers Distance between side buffers height of buffers when wheels are new and fully worn out Maximum height of the car with wheels in new condition Maximum height of the cab at corners with wheels in new condition Maximum width of the car Minimum height above rail level of any component with the car wheels in maximum worn conditions Reduction in the above height in the event of spring rigging failure Diameter of wheels over tread New worn Height of the center of gravity of car above rail level Axle load maximum minimum Adhesive weight Total weight of the car in fully loaded condition in empty condition Maximum speed of the car Geared Safe vehicular Maximum tractive effo
114. nges At such locations where the attachment is made to a flange suitable bulkheads shall be provided in the member at the location of the attachment to assist in transferring the load into the web Gussets are to be of full height Where dissimilar metals are joined they shall be protected against bimetallic electrolytic corrosion Bidder shall corroborate the reason for using the dissimilar materials at such specific locations Engineers or Inspector reserves the right to verify the quality of welds particularly in critically stressed areas by appropriate non destructive testing methods NDT CORROSION Protection of materials against all types of corrosion shall be appropriate for the environment of India and the operating conditions of the cars Corrosion protection methods for metallic components and equipment cases shall be submitted Where feasible such corrosion protection measures shall not require to be repeated throughout the life of the vehicle A corrosion resistant coating shall be applied to the entire underframe and the inside of side and end sheets A corrosion resistant coating is not required on stainless steel members except for sound deadening as may be necessary to meet the noise limits specified Protection against corrosion and painting of coaches shall be as per UIC 842 5 Exterior stainless steel shall not be painted FASTENERS Screw threads shall be of ISO metric sizes ISO Metric fine threads shall be use
115. ngest possible life consistent with the other characteristics specified All elastomeric parts shall be resistant to Ozone oxidation heat oil grease salts and acids The resilient mounts shall be of natural rubber Synthetic rubber compounds may be substituted for natural rubber only when approved for a specific application Life expectancy For all parts made by vulcanizing an elastomer to metal a service life of six years should be obtained when parts are used in normal service All rubber parts shall be compounded to be resistant to abrasion grease and oil kkkkkkk 44 4501 93 Effective from TI SPC OHE SPRC 1 1 1 2 1 3 1 4 1 5 1 6 Part IV Traction Equipment amp Controls GENERAL OHE Car shall be powered with suitable hp fuel efficient diesel engine and a proven and modern 3 phase AC AC transmission system with microprocessor based controls Successful tenderer should submit the design calculation for selection of diesel engine as per the requirement of this specification AC AC transmission system and allied microprocessor based controls shall be used with M s Cummins make 50 L4 diesel engine allied mechanical systems to manufacture suitable HP AC AC BG operation The specification has been prepared for general guidance of the manufacturer Any deviation from specification intended to improve the performance reliability and efficiency of the equipment as a
116. nt friendly Maximum possible commonality of structure components equipments and sub systems in the different types of cars This specification consists of six parts as follows Part I Chapter General requirement Chapter I OHE Parameters to be measured Construction of OHE Car and working environment Part II Operating and Service Condition Part III Mechanical Requirement Part IV Power Equipment amp Control Part V Electrical Equipments amp Power Supply Arrangement Part VI Test Part vii Schedule of quantities The stock shall meet the operating requirements specified in Part Il of this specification and shall be suitable for conditions of loading mentioned therein The contractor shall in addition to observing and complying with this specification be bound by the standard terms and conditions of contract for the design construction supply and delivery of OHE Car This specification is intended to include everything requisite to the construction of OHE Car notwithstanding that everything required may not be mentioned herein the supplier shall ensure that the OHE Car is complete in all respect and fit for operation The existing OHE recording cum test car is similar to a coaching stock of IR Proposed OHE recording cum test car shall be self propelled and shall have driving cabs on either ends The space for accommodating two DG sets of 50 kVA with sound proof compartment a well furnished
117. ntact loss 14 Quad PC 2 15 Heavy duty duplex laser printer A4 size 2 16 Heavy duty colour ink printer A3 size 1 17 Heavy duty dot matrix printer A4 size 1 18 chart recorder 1 19 DVD player with 53 cm flat screen LCD 1 display monitor 71 720f 93 Effective from SECHUDELE Training cost SN Item Description Qty Unit Rate Total Remark 1 a Operational training cost for 160 man hours handling equipments like recording sensors of measuring equipments reading and analyzing the recorded parameters Two Training cost for 160 man hours in handling of other electronic instruments system subsystem of the OHE car Two SECHUDELE D Annual maintenance cost 1 Cost of post guaranty excluding majour items for five years SECHUDELE Recommended spare parts cost 1 Cost of recommended spare parts for five years after expiry of AMC rate list to be attached 72 7301 93 Effective from Annexure l CONTRACT DRAWING SI no Drawing Drawing Number Title make 1 ICF DMU DPC5 1 1 508 Body bolster 2 ICF DMU DPC5 0 0 502 Bogie general arrangement 3 ICF EMU M 0 1 024 Primary helical spring 4 ICF DMU DPC5 0 2 504 Wheel amp axle 5 RDSO SK 911
118. of dust moisture A separate covered and closed room protected from dust ingress and connected to wheel storage parking line by a Railway track should be provided for pressing of roller bearings on axle journals 4 Adequate covered bay area served by EOT cranes to enable out turn of at least one unit ofOHE Car per month should be provided for manufacture of sub assemblies and assembly The EOT cranes should be provided with suitable lifting tackles 5 A separate line of adequate length for holding at least one OHE car for inspection and testing of OHE car dispatch line should be provided for final inspection and testing of DEMU coaches by the purchaser s inspecting Engineers The complete dispatch line should be served by facilities for EP brake testing 6 The dispatch line should be provided with a pit of the length of minimum OHE Car length and level track of OHE Car length for checking of car buffer height 7 The firm or its sub vendor where car will be manufactured should have the following M amp P for manufacture of OHE Car before placement of contract a Profile cutting machine for cutting plates to the required profile upto 32mm b Edge planning milling machine for edge preparation other than portable c Shearing machines cut to length line d Plate bending machine e Butt seam welding machine f Spot welding machine for welding of sidewalls with pillars 0 Adequate number of welding sets with current rating between 300 4
119. of manufacture vii The Contractor shall provide free of charge to IR personnel necessary information working dress where needed any safety glasses equipment and supplies during the training period viii The Contractor shall designate qualified specialists to advice and train IR technical personnel and explain relevant aspects related to product ix In case of illness or accident the Contractor shall arrange for medical care in the best possible way the cost of which shall be borne by IR X During commissioning of the OHE car technical experts of the manufacturer will fully and adequately train operators maintenance staff nominated by the consignee TRAINING ON MEASURING EQUIPMENTS The Contractor shall arrange to provide training on measuring instruments of the OHE recording car at their manufacturing works for four persons for a period of four weeks The charges for providing these facilities excluding travel boarding and lodging should be indicated separately To and fro expenses of the IR engineers and their boarding and lodging will be borne by the Indian Railways The total duration of training for each engineer shall be a Two week 10 working days in handling of imaging recording sensors and its interface through electronic instruments to on board computers and display of output on the display unit and reading and interpretation of tabular graphical report generated by the system and correct interpretation of actual me
120. ogramme protection and indication scheme overall dimensions and weight Technical details of DC link capacitors and any other filter choke offered by the tenderer for fitment at the DC link 3 Traction motor Make and type continuous rating one hour rating and short time rating design test service speeds starting current and duration current ratings for various operating voltages gear ratio traction motor characteristics under different voltage conditions details and data of windings including method of impregnation and varnish used estimated temperature rise in windings bearings etc cooling arrangement including ducting details rating under natural cooling details of insulation design of the bearings including L10 life and lubrication scheme details of data for motorette test evaluation criteria and test programme results of type and routine tests if conducted fits and clearances adopted overall dimensions and weight of traction motor detailed design features of suspension roller bearings if provided 4 Auxiliary machines Make and type of auxiliary machine starting current and torque torque speed characteristics at various voltages continuous rated power voltage current amp speed type of enclosure details of cooling fan air gap details of winding and insulation conductor size current density type of conductor insulation details of impregnation details of lead wire terminals and terminal block material of co
121. ols Make and type details of traction alternator excitation controls analog binary inputs outputs signals vehicle bus train bus interface CPU details and power supplies for electronic systems Details of interface with the traction inverter system and braking system Details of protection and indication system Details of adhesion control system Overall dimension weight and redundancy 11 Traction Gears amp Pinions Basic rack number of teeth module pressure angle helix angle if any profile displacement x m center distance between mating gears quality amp accuracies of gear teeth and other related information Material specification chemical composition and mechanical properties forging ratio etc Heat treatment process adopted for hardening the gears i e case hardening through hardening induction hardening Hardness at tip flank and root of the gear teeth Case depth of case hardened gears and hardness distribution of cross section in case of induction hardened gears shall also be furnished 12 Micro controller based governor for engine control Make and type functional details and parameters to be controlled interface parameters with the vehicle control system details of safety features details of display screen fault diagnostics and data logging features 79 800 93 Effective from TI SPC OHE SPRC Annexure CURRENT TAKE OFF 160 d BOW PROFIL
122. on 4 Installation drawing showing overall dimensions 5 Weight 1 8 Hydraulic pump for cooling system Type fixed variable Model Make Flow rate _PM speed Pressing setting Maximum permissible leak off HP consumed 1 9 Hydraulic motor for cooling system Type fixed variable Model Make Flow rate _PM speed Pressing setting Maximum permissible leak off HP consumed Dog 2 0 Roof mounted AC package unit RMPU 1 Make 2 Model 3 Type 4 Capacity 3 0 Traction Invereter 1 Make 2 Model 3 Type 4 Ratings 5 Weight kW 6 Type of Ventilation 4 0 Details of measuring equipments 1 Process of data collection 2 Make 3 Model 89 9001 93 Effective from Annexure XI 90 1of 93 Effective from TI SPC OHE SPRC CHAMFER CHA HDLRA IN EINTIND HEAD T T 1 T Lo og44 ae is Material Note 5 Ab ard sd li CONDEMNING LIMIT FOTE 1 ALL DIMENTIGNS ARE IN 2 THREE FIECE ONE PIECE DESIGN HE OFFERED WITH OR WITHOUT STEEL EXD PIECES 2 OYERALL DDMEXSIOGN SHALL HE MEASUEED WITH STEEL END FIECES IF 4 IN CASE OF THREE FIECE DESIGN 7 7 ee THE MEAX LEXG
123. ons homogeneous and free from defects and have their mating surface smooth and true to shape Castings shall be properly annealed and subjected to radiography tests where required 35 36of 93 Effective from TI SPC OHE SPRC 2 4 2 5 2 6 2 7 2 8 2 9 2 10 2 11 The use of aluminum and brass fittings for furnishing should be limited to the minimum extent in order to reduce pilferage Specific approval shall be taken before using such material Use of Aluminum in the under floor or in the load bearing areas shall not be desirable The material used shall be subject to the Suppliers corresponding QA procedures It shall be ensured that material of the requisite quality is used throughout the execution of the work All the materials to be used for interiors paneling furnishing lighting ventilation etc must comply with requirement for fire prevention protection of passengers in case of fire and from fire side effect according to international standards At the same time no materials are permitted within passenger compartments which contain asbestos toxic material or that may splinter or will create sharp edges when broken The type and make of the equipment once finalized during design stage shall not be permitted to be changed during the contract unless agreed by the purchaser and RDSO in writing in view of reliability and availability The Car body structure including sheathing sha
124. ormance requirement of the specification All the necessary drawings of the recording car shall be prepared and submitted to RDSO for prior approval The layout drawing shall depict the provisions for the following facilities i Instrumentation room for keeping on board computers UPS amp other accessories alongwith furniture etc ii Accommodation for on board staff officers cabin toilet cum bath facility kitchenette with cooking range and space for keeping LPG cylinder utensil refrigerator and other stocks along with the facility of water tap wash basin and sink etc il Separate room for commissioning 2 nos 50 kVA DG sets along with the facility to keep control panel fuel tank diesel oil storage and other connected accessories and equipment iv Driving cab at either end showing control desk and seating arrangement for the driver and staff v Observation dome with seating arrangement ladder and other facilities as per specification vi Separate layout drawing for electrical wiring showing lighting fans and all power supply points for equipment and instruments alongwith the location of distribution board vii Separate layout drawing for all the measuring equipment located inside the control room and roof mounted transducers interface and measuring equipments alongwith the control circuit vii Layout with mounting details of all under slung power equipment like diesel engine transmission cardan sh
125. pe and routine tests of the individual equipment of AC traction system shall be conducted separately Complete AC AC system shall also be tested after its installation on OHE Car In general traction inverter shall be tested in accordance with IEC 61287 amp control electronics of inverter and Vehicle Control System shall be tested as per IEC 60571 whereas traction alternator and traction motors shall be tested as per IEC 60349 Type and routine tests on other equipment shall generally be conducted in accordance with relevant IECs as mentioned at Annexure VI However if the tenderer proposes a different test scheme the same can be examined by RDSO on provision of alternative test procedures submitted by the tenderer The supplier shall submit detailed type and routine test programs to RDSO for approval RDSO may also decide to carry out some tests on any one or all the equipment which are not covered by relevant IEC specifications Tests shall be carried out as per mutually agreed test program and the total cost shall be borne by the manufacturer 1 4 The prototype of Alternator Traction Motor and Inverter Rectifier TCC and vehicle control 1 5 1 6 1 7 2 1 2 1 1 microprocessor will be tested by RDSO representative s at the manufacturer s premises All facilities for carrying out the prototype test should be made available by the firm After successful type test and fitment of measuring equipments the complete OHE Car will be
126. plate shall be provided on all top footsteps Any other suitable arrangement can also be considered Distance between the adjacent foot steps should approximate be 200 mm Door hand holds Door hand holds of stainless steel tubes or chromium plated steel tube with malleable cast iron brackets shall be provided on either side of all body side doors and shall be fitted so as to clear the side walls sufficiently to prevent injury to knuckles Hand holds shall also be within the car profile so that mechanized car washing is not hindered The doorsill shall be constructed from or equipped with slip proof profile with excellent wear resistance and drainage effect for rainwater Door locks All doors shall be fitted with reliable locks to be operated from outside and inside Hasps for external padlocking shall also be provided on all doors opening out of the Windows Double sealed glass windows of modular design shall be used in the air conditioned coach The outer glass shall be laminated and toughened safety glass which does not fall on breakage This should be indicated in the layout of the car for approval All window openings shall be true to dimensions square and of uniform width The window opening shall not at any point exceed 2 mm over or under the specified dimensions and shall not be out of square by more than 2 mm Two suitable emergency open able windows shall be provided in each side of coach Roof The roof shall be desi
127. plied Estimate of Car rolling resistance at various speeds Technical details of offered diesel engine Technical details of AC AC electrical transmission and other accessories Complete technical details of measuring equipments and their accessories Matching calculation of engine and transmission system alongwith tractive effort Vs Speed curve Technical details with supporting calculation for compressor Calculation for electric load capacity with details of Battery amp auxiliary alternator Fire detection system Design of doors Staff cabins officer cabin kitchen Lavatories etc Design of complete interiors including partitions interior paneling roof paneling flooring public address system seat cushioning and covering noise suppression measures heat insulation Layout of OHE Car Interior and exterior colour scheme Design of seats Complete lighting system Electrical couplers Power generation equipment Load imbalance calculation of the car Thermal and noise insulation measures 8 3 Approval to the drawings denotes general acceptability of the design features Notwithstanding such an approval the contractor will be wholly and completely responsible for the adequacy of the design of the OHE Car offered The contractor when submitting proposals on designs for approval of the RDSO shall draw specific attention to any deviation or departure from the specification involved in his proposals or drawings 8 4 To fa
128. procedure for austenitic stainless steel to be used in the manufacture of car The car body structure shall be designed to make effective use of metal in providing the required strength and stiffness Portions of the roof side frame and under frame shall be designed to form a girder to carry the longitudinal and vertical shear and bending loads resulting from the specified vertical loads In selecting the type and thickness of material to be used the Supplier s design shall optimize strength durability and weight The OHE Car structure shall be designed so as to withstand the load specified for the material used in accordance with International specification Body Bolster The design of Body Bolster shall be as per ICF drawing No DMU DPC 1 1 508 with latest alteration for OHE Car These may be fabricated from pressed sections and shall have suitable pads on which lifting slings may be placed The material of body bolster should be decided by manufacturer based upon design and strength considerations MATERIALS All materials used in the construction of the coach shall be of the specified quality and shall comply with the most recent issue of the relevant international standard specification The Supplier shall submit to the RDSO a list showing the names of the suppliers of components equipment and sub assemblies from whom they propose to obtain the materials and fittings for work under the Contract All castings shall be true to dimensi
129. r means the persons firms or departments nominated by the Purchaser to inspect the work on his behalf and the deputies of the Inspecting Officer so nominated 4of 93 Effective from TI SPC OHE SPRC 1 9 Contractor means the person firm or company from whom the Purchaser may obtain any material or fittings to be used for the work 1 10 Contract Drawings means the drawings which are included in Annexure of this specification for the guidance of the contractor The ICF drawings mentioned in this Annexure I should be collected from ICF Chennai 111 IEC 1 12 International Electro technical Commission 1 13 UIC Union International Des Chemins defer International Union of Railways 1 14 Horse Power HP shall be taken as metric horse power i e 75 kg metre sec 1 15 Tonnes T shall be taken as metric ton i e 1000kg 1 16 gt Overhead equipment is hereafter referred to as OHE 1 17 Self Propelled Overhead equipment parameter recording cum test car is hereafter referred as OHE Car 2 SCOPE OF THE SPECIFICATION 2 1 This specification covers the requirements of design development manufacturing and supply testing delivery and commissioning into service of suitable capacity of Self Propelled Overhead Equipment parameter recording cum test car with Stainless steel shell amp Modern Interiors and high tech measuring equipments in completely assembled and furnished condition herea
130. re stampings details of bearings including L10 life and lubrication schedule overall dimensions weight evaluation criteria and test programme type and routine tests if conducted 5 Auxiliary Inverter if offered relevant details as in case of main traction inverter The auxiliary power requirement catered to by this inverter as well as the reserve available for use in future shall be clearly stated 78 7901 93 Effective from TI SPC OHE SPRC 6 Auxiliary Drive for blowers The technical details and controls protection between AC supply to the terminals of the AC drive machines shall be submitted 7 Master controller Make and type rated current making and braking current position of reverser and throttle handle details of cam and auxiliary interlocks overall dimensions weight mechanical and electrical endurance test data 8 Contactors Make and type rated voltage and current making and braking capacity number of auxiliary contacts with control circuit voltage magnet valve and coil details overall dimensions weight mechanical and electrical endurance test data 9 Relays Make and type rated current and voltage range of setting rated control voltage rating of contacts details of material of the contacts type of enclosure temperature rise limit indication system provided overall dimensions weight and mechanical and electrical endurance test data 10 Microprocessor Contr
131. rt at rail Maximum continuous tractive effort Maximum speed of operation at maximum continuous tractive effort a Fuel oil consumption at 7596 of rated output of the diesel engine b Lubricating oil consumption at t km h km h kg Km h Wh 75 of rated output of the diesel engine 86 870f 93 Effective from TI SPC OHE SPRC PARTICULARS TO BE SUPPLIED BY SUPPLIER 1 The following particulars pertaining to diesel engine and auxiliary equipment shall be submitted by the tenderer 11 Diesel Engine ONOAPRWAN gt 14 15 16 17 18 19 20 21 22 23 General Data Exact description and model of the engine Rated output of the engine under site condition Rated engine speed Number and arrangement of cylinders Cylinder bore Piston stroke Compression ratios Mean piston speed BMEP at rated output Normal no load idling speed Peak firing pressure Full test result and data pertaining to engine tests Specific fuel consumption at various throttle position with tolerance band and site conditions Indicate the lower calorific value of the fuel used in arriving at the specific fuel consumption figure Fuel oil consumption at idle speeds normal amp low Lube oil consumption at rated output as percentage of fuel oil consumption De rating calculation for site condition Safety devices provided Over speed Low lube
132. s with 3096 chocked condition of radiator used Airflow required for the radiator fan shall be at least 1596 more than actually required to make up for any reduction in air flow due to train movement The limiting ambient capability of the cooling system should be minimum 55 C with 3096 chocked condition The initial fill of hydraulic oil for hydrostatic operation of fans in the cooling system as recommended by the manufacturer shall be in the scope of supply Side mounted radiator and hydraulically driven fan assembly with side panels shall be provided For ventilation of engine room hydraulically driven fan of adequate capacity shall be provided The hydraulic pumps and motors used for cooling will be of fixed displacement types Hydraulic hoses of proven make with adequate factor of safety shall be used for cooling system The hoses shall be properly routed and secured so that it does not fail due to vibration or infringement Water level indicator shall be provided on radiator tank and it should be easily visible and readable During operation at maximum out put the radiator fan and ventilation fan shall not be source for noise and vibration 49 50of 93 Effective from 6 7 The tenderer shall submit following details and calculations for the offered cooling system Cooling requirement for all sources of heat with break up Heat dissipation characteristics of the radia
133. separate OHE and the take of points are invariably arranged in such a way so as to have smooth passage of pantograph The turnouts and crossing from secondary tracks are provided with similar arrangement or with crossed type of equipments where other OHE has no overlapping span TECHNICAL DETAILS OF EXISTING OHE OF INDIAN RAILWAYS S N Description Details 1 0 OHE Simple Polygonal OHE regulated 2 0 Span 72 m Max on tangent track suitably reduced on curves Maximum variation between two adjoining span is 18 3 0 Tension 1000 kgf for catenary and 1000 kgf for contact wire 4 0 Contact wire 107 mm2 Hard drawn grooved copper HDGC 5 0 Catenary 65 mm2 cadmium copper 6 0 Maximum blow off 415 mm 7 0 Stagger of contact wire 200 mm on straight track amp 300 mm on curves 8 0 Relative movement of pantograph with reference to contact wire i Dynamic Normally the contact wire is within the 520 mm zone on either side of the track centerline i e 1040 mm which is the flat zone of the pantograph However during wind conditions the contact wire may go beyond this flat zone extending up to 800 mm on either size of the center line i e to cover a range of 1600 mm taking into account other factors such as oscillations loose joints etc ii Static For heavy wind conditions 860 mm from the centerline of pantograph is taken in to account 9 0 Mid span sag Partly 50mm to 100 mm var
134. stem design parameters key drawings calculations drawings and specifications documents in English language as required by purchaser for examination and shall provide explanation and clarification of the drawings for approval in metric units to RDSO within 12 weeks from the date of placement of order For the purpose the Supplier shall depute his respective technical experts for design discussions and finalization Approval or decision by purchaser shall normally be given within 4 weeks of submission of all clarifications by the Supplier to the satisfaction of the purchaser After the final design is approved the Supplier shall 9of 93 Effective from TI SPC OHE SPRC furnish complete set of specifications as mentioned in the approved drawings and documents within 45 days of design approval The detailed design and calculations shall cover Hauling capacity calculation Braking effort and EBD calculation on plane section and gradient with maximum load without load Calculation of centre of gravity of OHE Car from rail level details of weight transfer calculation tractive effort versus speed curve Load balancing calculations in longitudinal and lateral modes Shell along with FEM Modeling Finite Element Method with standard computer programs carried out for stress analysis of the car structure including vibration analysis of carbody Calculation for stability of the Car against wind force shall be sup
135. t of spares to be ordered finally shall be advised by the purchaser within 3months thereafter The tenderer shall be responsible for ensuring subsequent availability of spare parts for efficient working of the respective equipments The tenderer shall also submit time bound plan proposal for indigenous availability of imported components A spare part catalogue listing all components manufactured or purchased by the tenderer shall be prepared with in 45 days of design approval The contractor shall furnish one copies of spare parts catalogue to RDSO and two copies to the consignee free of cost COMMISSIONING OF OHE CAR The OHE Car shall not be dispatched or packed until the Inspecting Officer has passed it Such passing shall in no way exonerate the contractor from obligation in respect of quality and performance of the equipment In the event of dispute between the Inspecting Officer and the Contractor the decision of the Purchaser shall be final and binding The consignee shall inform the Contractor after the OHE Car has reached at site The OHE Car shall be commissioned by the Contractor within 4 weeks after intimation by the consignee The consignee will issue a commissioning certificate after it has been successfully commissioned 17of 93 Effective from 24 25 25 1 25 2 25 3 25 4 25 5 26 MAKER S CERTIFICATE Copies of Maker s certificate guarantee
136. t on jigs Interchangeability of all equipments hangers on all cars without the use of shims or elongated holes shall be ensured Adequate drainage shall be provided in all body structure members and elsewhere as necessary to preclude water entrapment Enclosed structural cavities shall be vented to prevent accumulation of condensate In areas where water might be ingested corrosion resistant drain pans and drain lines shall be provided and shall be arranged to divert the 36 3701 93 Effective from 3 2 3 2 1 3 2 2 4 1 4 2 5 1 5 2 discharge clear of all equipment and structure Means shall be provided to prevent clogging of drain lines and drain holes enclosed structural cavities of the steel members shall be treated with a rust inhibiting coating Interior floor should be capable of being washed with hose pipe There should be no location where water may stagnate SURFACE FINISH AND FLATNESS All exterior non corrugated surfaces shall be free of ripples and buckling The surfaces of flanges and webs of all structural members shall be straight and flat and free of ripples buckling dents gashes and other surface imperfections When the car body structure is assembled the exterior surfaces shall be flat within the following tolerances when measured over a distance of 1m and in similar proportion for shorter lengths on unpainted body shell without any f
137. t terrain in certain areas during hot The dust concentration in air may reach a high value weather of 1 6 mg m In many iron ore and coalmine areas the dust concentration is very high affecting the filter and air ventilation system 6 Coastal area Car and its equipment shall be designed to work in 29 30of 93 Effective from TI SPC OHE SPRC 3 12 3 13 3 14 coastal areas in humid and salt laden atmosphere with maximum pH value of 8 5 sulphate of 7 mg per litre maximum concentration of chlorine 6 mg per and maximum conductivity of 130 micro Siemens cm 7 Vibration The equipment sub system and their mounting arrangement shall be designed to withstand satisfactorily the vibration and shocks encountered in service as specified High level of vibration and shocks with accelerations over 500 m s have been recorded at axle box levels for long periods during run Vibrations during wheel slips are of even higher magnitude 8 Wind Pressure High wind pressure in certain areas with wind pressure reaching 200 kgf m 9 Environment for Measuring equipment shall be suitable to perform measuring satisfactorily under 25 kV AC environment equipment The rain fall is fairly heavy and during dry weather the atmosphere is very dusty The car should be able to negotiate water logged tracks with water level about 102 mm above the rail top for which t
138. t the sides and ends and fire resistant equipment housings Flammable materials shall be well contained and protected Materials used in the construction of each OHE Car shall be selected to reduce to the maximum extent practical the heat load rate of heat release propensity to ignite rate of flame spread smoke emission and toxicity of combustion gases All non metallic and furnishing materials such as artificial leather seat covering flooring material vestibule material GFRP paneling cushioning material etc shall satisfy the requirements of resistance to spread of flame and deterioration in visibility due to smoke etc as per UIC 564 2 OR Class A or superior International standard The toxicity value when tested as per Indian Naval Spec NCD 1409 shall be less than 1 0 Limiting oxygen index when tested as per IS 13501 shall be 35 min A reliable automatic fire smoke detection system shall also be provided on the car The system should not cause any discomfort or undue alarm to the travelling public The design of the system shall be got approved by purchaser SPECIFICATION REQUIREMENTS Unless specified otherwise in this specification cars shall meet all requirements of UIC in respect of car design Where UIC specification does not exist relevant EN IEC DIN BS standard should be followed kkkkkk 34 3501 93 Effective from TI SPC OHE SPRC 1 1 1 2 1 3 1 4 1 5 1 6 2 1 2 2 2
139. testing may be offered through which it should be possible to offline test the inverter by inserting a test EPROM or by downloading a test program in FLASH Features to take corrective action in case of recognizable faults The inverter system should have its own protection and control logic which it should also be able to communicate with the loco control system in the event of a fatal failure to initiate a protective shutdown of the OHE Car The protective shutdown in case of defined fatal conditions shall be based predictable logic preferably implemented in the hardware of inverter electronics Damage to IGBT devices of the inverter shall be prevented in case of a short circuit at the load end 14 7 Proper shielding against electric and magnetic interference shall be provided Cable length for gate drive timing signals transmitted from traction control system shall be kept minimum to minimize losses and prevent loss of data Actual firing pulses shall be generated by gate drive units mounted in the phase modules Proper electrical isolation for low voltage gate drive signals and high voltage gate drive power supplies shall be provided Proper creepage distances between high and low voltage circuits as well as to the ground shall be maintained 55 56of 93 Effective from 15 16 16 1 16 2 16 3 16 4 16 5 16 6 17 D C LINK For smoot
140. thstanding any approval which RDSO or the Inspecting Officer may have given of the detailed drawings prepared by the contractor of his Sub contractors for materials components and sub assemblies of other parts of the work involved in the contract of the tests carried out by the contractor sub contractor or RDSO or the Inspecting Officer CONTRACT SPECIFICATION Copies of Indian Railway Standard Specification and Schedule of Maximum and Minimum Dimensions may be obtained on payment from the Controller of Publications Government of India Civil Lines Delhi 110054 India Copies of IS Specifications are available from the Bureau of Indian Standards 9 Bahadur Shah Zafar Marg New Delhi 110002 The tenderer shall submit a copy of English version of International specifications used for design and manufacture of OHE Car DESIGN DEVELOPMENT amp APPROVAL OF DRAWINGS After the contract is signed the Supplier shall within 45 days of signing of contract furnish to purchaser the detailed schedule programme for submission of design documents for approval which shall be suitably staggered to enable purchaser to plan for expeditious clearance Any calculation that is evaluated on the basis of software simulations shall be supported with sample calculations The contractor shall develop the design based on the details given in this specification and sound engineering practices The Supplier shall deliver all necessary data sy
141. tor and its resistance characteristics Radiator fan characteristics showing the air flow Vs total heat at different speeds Cooling system matching calculations Schematic cooling circuit diagram showing water oil and airflow arrangement shall be provided e Cooling proving trial including testing of hydraulic oil cooler shall be conducted at contractor s premises to prove adequacy of the offered cooling system for prototype in presence of authorised representatives of purchaser The maximum temperature of hydraulic oil shall not exceed 70 C 6 8 The hydraulic oil tank shall be of stainless steel It shall be provided with oil level indicator temperature indicator oil level switch and oil filter with restriction indicator A micro limit switch shall be provided and interlocked with delivery side shut off valve 7 POWER TRANSMISSION SYSTEM 7 1 The OHE car shall be powered by CIL make or equivalent or better proven make fuel efficient diesel engine capable of producing adequate power output to meet operating and service condition mentioned in part Ill under standard conditions The engine shall be adjusted to deliver suitable power to the alternator under site conditions 7 2 rectified traction alternator output shall be fed to traction inverter s through a DC link Traction inverter system shall be used to generate 3 phase variable voltage variable frequency VVVF output to be fed to four 3 phase asynchronous traction mo
142. tored throughout the warranty period and report submitted to enable purchaser to assess acceptability of the cars and its components for reliability and maintainability The report shall include all pertinent data log summaries and where applicable the corrective actions taken Annual Maintenance Contract AMC The tenderer shall quote separately for AMC for complete system excluding diesel engine complete bogie transmission system complete compressor unit Traction alternator Traction Invertor 50 DG set and UPS etc for 5 years after the guarantee period is over The tenderer shall quote year wise rates of AMC detailing the various schedules enlisting the requirement of material spare parts and services to be rendered by him after regular intervals The tenderer shall keep adequate spares in stock for regular schedule of AMC so that maintenance schedules are completed timely The AMC cost shall be considered while evaluating the inter se tender position It shall be compulsory for the tenderer to quote for AMC However the decision to enter into AMC shall vest with Railway alone The tenderer shall also quote indicating list of recommended spares with rates to be kept after guarantee amp or AMC period is over 30 days down time of the complete system inclusive of comprehensive scheduled maintenance shall be allowed in a year If down time exceeds more than 30 days in a year the penalty of Rs 5000 per extra day shall be recovered
143. tors connected in parallel Inverter output voltage and frequency shall be matched to traction requirements over the entire speed range of the power Car and shall be continuously regulated 7 3 An auxiliary generator shall be provided to cater to battery charging controls and lighting requirements 7 4 The 3 propulsion equipment should be offered such that alternator excitation and engine HP for idle and intermediate notches are so chosen that the engine is operated at the optimum SFC points 7 5 All electrical equipment shall comply with relevant latest IEC AAR IEEE standards Tropical humid weather conditions prevailing in India shall be kept in view in the design of all electrical components Detailed information about traction machines and equipment used shall be furnished as per Annexure V 8 TRACTION ALTERNATOR 81 three phase synchronous alternator preferably with integrated brushless excitor and rotating diodes shall be offered The traction alternator shall be of self ventilated type 8 2 traction alternator offered shall be directly coupled with the engine The mounting arrangement of the engine with alternator shall be decided mutually between engine manufacturer and tenderer No any modification will be carried out in the engine engine block for the purpose of mounting the proposed traction alternator If any modification is required for successful mounting of the proposed traction alternator it shoul
144. trol Excitation control of Main Alternator Traction Control Wheel Slip Control Control of Auxiliaries On line Fault Diagnostics Speed recording Display of operating status faults in the traction equipment electronics Communication with Traction Control computers FAULT DIAGNOSTICS The Vehicle Control System shall monitor the temperatures pressures currents and voltages of various traction equipment and identify the faulty equipment Whenever a fault is identified the control system shall take appropriate action to restrict the operation of the OHE Car depending upon the fault and to save the other equipment from consequential damage The system should preferably have a built in feature to ensure that in case of failure of a component OHE Car operation if feasible is either not vitiated at all or downgraded only in such a manner that the OHE Car is enabled to complete the trip safely A set of data packs and an appropriate fault message shall be recorded in a nonvolatile memory It shall be possible to download the faults through a Laptop PC by the maintenance shed staff An application software shall be provided for use on Laptop PC It shall be menu driven and easy to use by maintenance shed staff without any requirement for much computer literacy DISPLAY UNIT All displays shall be on LCD monitor There shall be two display screens one in front of the driver which shall continuously display important data such as Car speed
145. trumented trials testing modifications if any and RDSO clearance intensive service trials for 500 Kms of running will be done During the tests trials or during the guarantee period if any problems are thrown up or feed back information is obtained which warrants a re check of the design manufacture quality of the equipment and components action will be taken as may be necessary by the Supplier to carry out the required investigations and to incorporate the improvements considered most appropriate to reach compliance with the specification amp to ensure specified reliability and performance without any extra costs to the Purchaser Modifications mutually agreed to and complying with the specification will be incorporated by the Supplier at his own cost in the OHE Car in a manner approved by RDSO Drawings incorporating the modifications as found necessary as a result of test and trial will be submitted to RDSO for approval before carrying out the modifications 140 93 Effective from TI SPC OHE SPRC 15 5 16 17 17 1 17 2 17 3 17 4 18 19 1 19 1 1 19 1 2 19 1 3 The Supplier shall further notwithstanding any exercise by the Inspecting Officer of the power of superintendence be responsible for the sufficiency of the packing marking etc of all imported parts of the work to ensure their delivery in India without damage SPECIAL OR PROPRIETARY FITTINGS All royalty char
146. tted to underside of car body This will detect lateral impulses in the OHE car body which if excessive shall reflect on the stagger measurement ii Lateral motion measured by two linear potentiometers placed symmetrically about the bogie axis of rotation The half sum of the two voltages shall give the lateral motion independently of bogie rotation Any other method which is more accurate and suitable to measure at higher speed of recording car may be offered If the tenderer feels that his proposed method is superior to the methods given above Tenderer have to submit the detailed procedure and justification for acceptance of the purchaser contractors design should have given satisfactory performance for a minimum period of two years on railway networks elsewhere Typical lateral acceleration values in respect of comparable vehicles have been found to be in the order of 0 279 the criterion limit however is 0 55g e Loss of contact The quality of current collection is measured in terms of loss of contact between the pantograph and the contact wire as indicated below The number of times the contact is interrupted while the OHE car is in motion and The duration of time for which the contact has been interrupted while the OHE car is in motion The contact losses and their duration are to be measured and recorded continuously while the OHE car is in motion Contact loss ratio should be calculated by dividing the sum of
147. uld preferably be provided with a built in self protection function to avoid failure on over temperature in case of failure of temperature sensor 13 9 The proposed inverter system shall be modular in construction so as to facilitate ease of maintenance and replacement In case of any fault removal and replacement of phase modules should be easy Tenderer shall confirm support for obsolescence of all semi conductor devices for a minimum period of 15 years 13 10 Preferably forced air cooling shall be used for inverters It is preferable that cooling requirement of complete inverter system be met by blowers that are located inside the inverter cabinet s itself 13 11 The weight of the Inverter and rectifier combined should be approximately 2 tons 14 14 1 14 2 14 3 14 4 GENERAL POINTS FOR TRACTION INVERTER DESIGN Inverter shall be of PWM type with high switching frequency to obtain near sinusoidal waveform and reduce current harmonics even in the lower speed region of traction motor The harmonics of the output waveform of inverter shall be controlled to minimize the traction motor torque pulsations traction motor heating and also to provide constant and high adhesion between wheel and rail throughout the operating speed range of the OHE Car The components and technology used shall ensure very high efficiency of the inverter system Typical efficiency of about 98 is preferred Manufacturer shall furnish the expected eff
148. upply of control system and instrumentation for two cabs for bi directional operation of vehicle Supply of GPS recorder along with antenna and accessories to view the GPS data directly on Necessary interface to interface the GPS receiver data with the measured data so that the data can be seen on the google earth Supply of high sensitivity thermo vision camera for thermal scanning of OHE at 120kmph as per RDSO s spec No TI SPC OHE ITIC 0100 02 2010 Installation amp commissioning of item 2 to 11 above SECHUDELE B Measuring equipment instrumentation amp software for SN Item Description Qty Unit Total Remark Rate 1 Contact wire thickness 1 2 Contact wire stagger and height a upto 700 mm stagger 1 Alternate offer b upto 350 mm stagger 1 3 Contact wire slope 1 4 Compensation system of vehicle oscillation 1 5 Electrical cabinet and processing software 1 6 Acquisition amp supervision software 1 7 Installation and commissioning support 8 Vehicle kilometric progressive encoder 1 base 9 Mast identification system 1 10 GPS positioning system with software to 2 transfer data to PC Laptop and antenna etc 11 Compensation system of the wire position 1 12 Optical identification of mast location 1 13 Pantograph dynamic measurement contact 1 force acceleration co
149. ying from span 27 m to 72m 10 0 Condemnation size of 74 mm2 reduction in vertical height from contact wire 12 24 mm to 8 25 mm 11 0 Gradient of contact wire The maximum contact wire gradient is 3mm per meter and permissible variation in gradient over 2 consecutive spans is 1 5 mm meter variation of 1 5 mm m on consecutive span 12 0 Spacing of droppers First dropper 2 25 m from support second one is 4 50 m 6 75 m and thereafter the droppers are at 9 m spacing 13 0 Permissible uplift of 60 mm at registration arm contact wire 83 8401 93 Effective from Track Details 1 Maximum super elevation 165 mm for group A B and C routes 140 mm for group D and E routes in special case 185 mm for A route 2 Maximum Cant deficiency 100 mm for group A and B and 75 mm for group C D and E routes 3 Radius of sharpest curve and 175 m and 1 in 8 5 respectively turnout 4 Track tolerances i On Straight 6 mm to 6 mm ii On curve with radius 6 mm to 15 mm 350 m or more iii On curve with radius up to 20 less than 350 m 5 Gauge Widening on curves 5mm to 3mm Straight including curves of radius upto 350 mm and more For curves of radius less than 350mm and more These are with reference to nominal gauge 1676mm up to 10mm 6 Minimum clearance above the rail level In fully loaded condition and with worn wh
Download Pdf Manuals
Related Search
Related Contents
capitolato d`oneri vol. 5a - Università degli Studi della Basilicata EVGA 012-P3-1570-ER NVIDIA GeForce GTX 570 1.25GB graphics card MANUAL DEL USUARIO - X Scarica il manuale istruzioni ANLCI (Agence Nationale de Lutte contre l`illetrisme) (pdf SmartPAT 5500 Thanks to a powerful Quad Core processor, your Quartet 364 Copyright © All rights reserved.
Failed to retrieve file