Heavy Duty Vehicle Stands - Shinn Fu America Homepage
Contents
1. HEIN WERNER AUTOMOTIVE Heavy Duty Vehicle Stands Operating Instructions amp Parts Manual Model Number Capacity per pair HW93524 7 Ton HW93526 25 Ton Made in the U S A HW93526 HW93524 t At is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death SFA Companies 10939 N Pomona Ave Kansas City MO 64153 customerservices heinwerner automotive com Read this manual and follow all the Safety Rules and Operating Instructions before using this product HW93524 M0 rev 08172010 SAFETY AND GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this pair of vehicle stands before using The owner and operator of this equipment shall have an understanding of the jack stands and safe operating procedures before attempting to use The owner and operator shall be aware that use of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of these jack stands is authorized If any doubt exists as to the safety or proper use of these vehicle stands remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts including labels are noted Any stand that appears damaged i2. are provided to prevent inadvertent A separation of the column from the base Handle assembled stands with care OPERATION NEVER use jack stands to support both sides or one end of a vehicle Use only one 1 pair per vehicle Rated capacity is per pair only Do not exceed rated capacity Use only on areas of the vehicle as specified by the vehicle manufacturer Use ONLY on vehicles whose support points are compatible with the saddle of the jack stand Incompatibility may result in structural damage to the vehicle and or jack stand Structural damage to either may result in sudden and unexpected loss of load height A Only attachments and or adapters supplied by the manufacturer shall be used 1 Adjust saddle height by pulling up the extension tube then insert the support pin through the appropriate hole on extension tube 2 Ensure that support pin is secure and nested across two corresponding semi circular cutout on the collar before loading Insert support pin into the extension tube far enough to create equal distance of pin extending from the extension tube on both sides 3 Carefully position stands so that load is centered on stand s saddle 4 Slowly lower the vehicle onto the stands 5 Check to ensure vehicle is secure before working on around or under To lower load A Be sure that all tools and personnel are clear before lowering load 1 Raise vehicle clear of stands with suitable jack 2 Carefully release support pi
3. LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO TWO YEARS OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies 10939 N Pomona Ave Kansas City MO 64153 816 891 6390 customerservices heinwerner automotive com
4. n and allow extension tube to glide down to lowest position 3 Carefully remove stands and place stands away from the work area 4 Carefully lower vehicle with jack MAINTENANCE Periodically inspect each stand Ensure all parts move freely Do not apply oil or grease to any portion of this product If rust appears sand affected area and cover with suitable utility paint Please note that there is no replacement part applicable to this device Storage Store jack stands in upright position and in a clean dry area 3 REPLACEMENT PARTS PART NO DESCRIPTION 928062 7 Ton Pin amp Chain Assy 928065 25 Ton Pin amp Chain Assy AUTOMOTIVE TWO YEARS LIMITED WARRANTY For a period of two 2 years from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA COMPANIES SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR
5. n any way operates abnormally or is missing parts shall be removed from service immediately If you suspect that the jack stand was subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until the stand has been checked by a factory authorized service center contact distributor or manufacturer for list of Authorized Service Centers It is recommended that an annual inspection be done by qualified personnel Labels and owner s manuals are available from manufacturer PRODUCT DESCRIPTION Hein Werner Heavy Duty Vehicle Stands are designed to support rated capacity partial vehicle loads consisting of one end of a vehicle Use vehicle stands as a matched pair to support one end of a vehicle only Stands are not to be used to simultaneously support both ends or one side of a vehicle Rated capacity is per pair SPECIFICATIONS Capacity per Pair Min Height Max Height Height Intervals Collar T Se Saddle Zs a gt Carry Handle y ie g A G Height Adjustment Holes Base Section Y l G Extension Tube TN P Figure 1 Heavy Duty Vehicle Stand Components BEFORE USE refer to Figure 1 for location of components 1 Verify that the product and the application are compatible If in doubt contact Hein Werner customer Service 2 Inspect stands before each use Do not use if there Study understand and follow all instructions provided with and on this device before
6. use Rated capacity is per pair Do not exceed are bent broken or cracked components including rated capacity labels Use as a matched pair to support one end of a 3 Ensure that all parts move freely vehicle only Use only one 1 pair per vehicle 4 Before use read the owner s manual completely and Use only on hard level surface familiarize yourself thoroughly with the product and the Center load on saddle hazards associated with its improper use Stands are not to be used to simultaneously 5 Always refer to the vehicle owners or service manual support both ends or one side of a vehicle for location of proper lift and support points No alterations shall be made to this device Failure to heed these markings may result in Lift and support points may differ from vehicle to personal injury and or property damage vehicle The owner and operator of these stands shall be aware that special training and knowledge may be required in the proper placement of jacks and stands Lift and support only those areas as e Leer comprender y seguir las instrucci nes antes recommended by the vehicle manufacturer Con de utilizar el aparato sult the manufacturer s service manual for the lo e El manual de instrucci nes y la informaci n de cation of proper lift and support points seguridad deben estar comunicado en lengua del operador antes del uso e No seguir estas indicaci nes puede causar da os personales o materiales No means
Download Pdf Manuals
Related Search