3240 Installation Instructions
Contents
1. off the ignition Installation of this product requires AT LEAST 1 8 clearance between the back of the speaker arm and any accessory I E luggage rack bag mounted on the trunk lid On 06 10 GL 1800 s this product requires the separate purchase and installation or the motorcycle to be equipped with Kuryakyn Rear Accessory Light Adapter P N 3241 On 12 UP GL 1800 s this product requires the motorcycle to be equipped with Kuryakyn Rear Accessory Plug and Play Harness P N 3230 NOTICE A factory service manual may be helpful in performing this installation Do not attempt to perform this installation if you are 3240 24GL 0313 not confident in your ability to complete all of the steps in the procedure consult a trained technician cont CUSTOMER SERVICE INSTALLATION QUESTIONS LIMITED WARRANTY ABOUT OUR CATALOG K uryakyn STEP 3 Thoroughly clean the back of both passenger armrests with soapy water and a M CLEAN THIS AREA ON clean rag Dry completely Thoroughly clean the installation area with an ammonia i BOTH SIDES OF BIKE based cleaner such as window cleaner and a clean rag to remove any residue of ak any silicone based plastic brightener that has been used PIC 1 Dry completely Wipe the installation area with the included alcohol pad to remove any residue P aa STEP 4 Determine the left sitting on bike from the right Armrest Accent PIC 2 NOTICE Ensure the area of installa2. INSTALLATION L E D ARMREST ACCENT for GL 1800 3240 PARTS INCLUDED PRE OrRPRPrH Left Passenger Armrest Accent Right Passenger Armrest Accent Run Turn Harness for Armrest Accents Double Y Adapter 6 Black Nylon Cable Ties Dielectric Grease Pack Alcohol Pad Installation Instructions Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING KURYAKYN IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS WARNINGS CAUTIONS AND NOTICES REGARDING THE USE AND CARE OF THIS PRODUCT THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY This indication alerts you to the fact that ignoring the NOTICE contents described herein may negatively affect product performance and functionality IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY NOTICE PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF THE IMPORTANT INFORMATION CONTAINED IN THEM TOOLS SUGGESTED Set of Metric Hex Wrenches STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS STEP 1 NOTE NOTE Read and understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface and turn
3. e a piece of wire or a straight coat hanger to pull the wire through and run it along the inside of the left frame rail PIC 9 i i a 4 until you can reach it from the back of the bike The wire should i mA4 0 P oe come out to the top left of the inside back panel Tape the six pin A sai HARNESS RETAINERS _ connector end of the Run Turn harness to the wire Secure the wire at an bw 7 tight enough that it will not come undone in the routing process Pull m the wire or coat hanger back toward the rear with the wires still secured to it Once P the wires are pulled far enough to reach they can be removed from the wire coat EE TRUNK UNDER BACKREST hanger Use the included cable ties to secure the harness out of harms way DY i g y N a Pa STEP 12 Please refer to the instructions for P N 3241 for 06 10 models or N ik Pe P N 3230 for 12 UP models If you have an open six pin connector on the Plug m A and Play Harness P N 3230 or Rear Adapter Harness P N 3241 connect the six Sa F pin connector from the Y harness to it If you do not have an open connector disconnect one of the six pin sets and connect the included Double Y connector in EEE D F line PIC 10 Connect the existing accessory and the Accent Lights to the new SONNE TO A HANE DOWNER N W A A Ae connector Use the included cable ties to secure the harness out of PIC 3 z B roure AE EERO NOTICE Secure all wiring away from any moving parts p
4. e one fastener behind the license plate STEP 9 Open the trunk Route the wire harnesses from each Accent along the OEM harness on each side of the trunk PIC 6 to the center of the motorcycle under the seat PIC 7 Use the OEM wire harness retainers and the included nylon cable ties to secure them out of harms way PIC 6 NOTE Make sure that the wire harnesses from the Accents DO NOT get pinched in the hinges STEP 10 Locate the Run Turn Y harness Connect the three pin connector marked left with the ORANGE RED and BLACK wires to the Accent attached to the left sitting on bike armrest Connect the three pin connector marked right with the BLUE RED and BLACK wires to the Accent on the right armrest PAGE cont L E D ARMREST ACCENT INSTALLATION STEP 11 On 12 UP models Requires the separate purchase and installation of Kiiryakyn P N 3230 to complete installation Route the six pin connector on PIC 6 the end of the Run Turn harness under the seat and along the main PIC 6 harness along the frame on the RIGHT side of the motorcycle PIC 8 Z A K Uryakyn to the rear of the motorcycle It may be helpful to use a guide wire Use the included cable ties to secure the harness out of harms way ane ss _ Be le isn My ae TER has N sd On 06 10 models Requires the separate purchase and x ser EN installation of K ryakyn P N 3241 to complete installation Fi _ Tak
5. inch points or extreme heat K ryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched crimped broken abraded melted or frayed wires STEP 13 Turn the motorcycle on and verify that the lights work correctly RIGHT SIDE UNDER PASSENGER SEAT SHOWN ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE LEFT SIDE UNDER A WARNING MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR ee RT MOTORCYCLISTS A LIGHT MALFUNCTION COULD RESULT IN Tar DEATH OR SERIOUS INJURY STEP 14 Replace the seat and rear fender panel ROUTE HARNESS ALONG THIS HARNESS 4 WARNING AFTER INSTALLING THE SEAT PULL UP ON IT TO ENSURE IT 0N 01 10 monELS IS LOCKED INTO PLACE A LOOSE SEAT CAN SHIFT AND CAUSE LOSS OF CONTROL RESULTING IN SERIOUS INJURY OR DEATH NOTICE It is the installer s responsibility to ensure that all of the fasteners 3 including pre assembled are tightened before operation of the motorcycle Kuryakyn will not issue a warranty on components lost due to improper installation Periodic maintenance may be required Ride On 3 L E D ARMREST ACCENT INSTALLATION
6. tion is free of grease oil dirt or other e debris including wax polish products and bugs to ensure proper adhesion K ryakyn WILL NOT issue a warranty on any parts lost due to improper installation i 5 NOTICE The adhesive will not bond correctly if applied at temperatures less e than 50 F Do not attempt this installation in temperatures less e ae o than 50 F A STEP 5 Spread the passenger armrest portion of the backrest away from the trunk PIC 3 Route the wire harness from the Accent into this space STEP 6 Test fit the right Armrest Accent to the rear of the right passenger armrest PIC 4 The Accent should follow the contour of the trunk and line up with the top of the passenger armrest Make any reference marks along the outside edges of the Armrest Accent with a non permanent marker or masking tape STEP 7 Rub the backing paper of the Accent with your fingernail to activate the adhesive Remove the backing paper and attach the Accent to the back of the passenger armrest Press in place for one minute full bonding will occur in 24 hours Repeat Steps 4 and 5 for the left side NOTE If the motorcycle is to be operated before the 24 hour cure time has expired use a good quality masking or painter s tape over the Accent to assist in holding the Accent in place until the cure time is over STEP 8 Remove the seat and the rear fender panel as outlined in the service manual PIC 5 NOTE Older models may hav
Download Pdf Manuals
Related Search