Installation Instructions
Contents
1. STEP 5 STEP 6 STEP 7 STEP 8 STEP 9 STEP 10 STEP 11 STEP 12 STEP 13 WARNING STEP 14 cont Take off the license plate and bracket off the back panel Slide the chrome tabs off the ae exposing the screws for the lower saddlebag corners Remove the hardware ae THESE is holding on the saddlebag corners PIC 2 Open the saddlebags exposing the hardware that secures the saddlebags to the ae FROM BOTH SIDES bike Remove the back two hardware bolts and loosen the fronts but do not fully remove them PIC 3 With the saddlebags loose remove the rear fender by sliding it downward You will notice the rear fender has slots that join the saddlebags to the fender itself If there is still resistance you may have to shift the rear fender to fully unlock the fender PIC 3 INSIDE VIEW OF THE SADDLEBAG Locate the red 6 pin connectors on each side of the rear light bar PIC 4 Unplug both red connectors On the bike locate the red connector that has the orange wire left side plug our connector that has the yellow and brown wires in between the red plugs PIC 5 On the other red connector that has the light blue wire right side plug in our connector that has the blue and green wires in between the red plugs PIC 6 i LOOSEN FRONT HARDWARE BUT DO NOT FULLY REMOVE i a You should have one four pin connector left This connection will be used to supply the power to the trailer PIC 7 Now go to t2. the added amperage from the trailer accessory will not overload the chosen circuit PIC 6 GREEN AND BLUE WIRES WHEN THIS SINGLE RED WIRE WITH THE RING TERMINAL IS CONNECTED TO THE BATTERY IN STEP 15 THE RED WIRE WITH THE BLACK STRIPE WILL HAVE POWER AT THE OTHER END OF IT MAKE SURE IT IS CAPPED OFF AS THE RED WIRE IN STEP 13 OR ATTACHED TO THE TRAILER PLUG BEFORE ATTACHING THIS WIRE TO THE BATTERY Attach the single red wire from the other end of the fuse holder with the ring terminal to the positive side of the battery PIC 8 Connect the long black ground wire to the negative on the battery using the supplied 1 4 ring terminal you will need to crimp this to the black wire PIC 9 On the back of the bike plug the Trailer Isolation Relay Kit to the sub harness With the two four pin plugs connected use a test light to check for proper function Turn the key on and test both signals Yellow is left and Green is right turn Brake lights Blue and Run light Brown The red wire with a black stripe is a power wire that can be used for keyless entry power or interior lighting on the trailer The white wire is ground PIC 10 heat K ryakyn WILL NOT issue a warranty on any electrical component PIC 8 that fails due to pinched crimped broken abraded melted or frayed wires Tie up any excess wire length with the provided cable ties Locate an area on the bike that you will be able to mount the trailer isolation relay b
3. you to the fact that ignoring the contents AE E EE EE EEA PE EEE ter described herein may negatively affect product performance and one 1 year from the date of purchase by the functionality i oe ED toy h r aur ay ante of TOOLS SUGGESTED M arate ilar arr cet Set of Hex Wrenches Combination Wrenches Wire Stripper Crimping Pliers Side Cutters Test nodules wiring chrome amp other component Light or Multi Meter Electrical Tape Heat Shrink my p STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE distributed by Kuryakyn Kuryakyn will pass or PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS where poseible will expedite the daimon behalf STEP 1 Read and understand all steps in the instructions before starting the i Aa A ae installation Park the motorcycle on a hard level surface and turn off the ABOUT OUR CATALOG ignition For purchasing K rya k n prod cta yor ATTENTION A factory service manual may be gt helpful in performing this installation Do not attempt to ue perform this installation if you are A not confident in your ability to lel complete all of the steps in the procedure consult a trained jaaa i d technician STEP 2 Remove the four Phillips screws that secure the lower trunk molding PIC 1 OO e o uu REMOVE THE FOUR SCREWS THAT SECURE THE LOWER TRUNK MOLDING a 7674 22GL 0212 cont PIC 1 _ STEP 3 STEP 4
4. INSTALLATION PLUG amp PLAY TRAILER WIRING for GL 1500 7674 PARTS INCLUDED CUSTOMER SERVICE 1 Trailer Wiring Isolation Harness with Relay pee eens reece 1 GL 1500 Trailer Wiring Sub Harness INSTALLATION QUESTIONS 1 Inline Fuse Y Harness with Heat Shrink Covered Butt Connectors techsupport kuryakyn com 1 1 4 Ring Terminal or call 715 247 2983 1 Hardware Kit Containing LIMITED WARRANTY 6 Black Nylon Wire ties 8 Kuryakyn warrants that any Kiiryakyn product 1 Dielectric Grease Package i SOIG herel bes l S nag aie ee one fects in 2 1 X 2 Adhesive Backed Hook Strap eae E Ouse 2 1 X 2 Adhesive Backed Loop Strap consumer ex cepting the follov ling p ovisions 1 Alcohol Pad ki aoni 1 Installation Instructions Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING K RYAKYN A IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR Ampa tiie pee toai gold DIAN PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL eee ee shots INSTRUCTIONS WARNINGS CAUTIONS AND ATTENTION NOTES REGARDING E once nena seat meen dina THE USE AND CARE OF THIS PRODUCT labor and pi int rest ting rom fe lure of a WARNING THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING for any breech of contract or duty between THE CONTENTS DESCRIBED HEREIN CAN RESULT IN erie ae e a POTENTIAL DEATH OR SERIOUS INJURY ins eci ap lications K ryaky makes no ATTENTION This indication alerts
5. he right side of the bike driver s right and remove the side cover located just below the seat This will expose the battery which will be needed to wire power to the relay harness You will also need to remove the seat Remove the fasteners that secure the seat There will be four bolts that secure the seat through the passenger handles Take a piece of wire or a straight coat hanger to pull the wire through and run it 7 COMPLETELY between the frame and saddlebag above the battery until you can reach it from REMOVE REAR the back of the bike With the supplied Trailer Isolation Relay Kit take the red i BOLTS wire red with a black stripe power and black ground wires and tape them to the 7 wire these will be in black sheathing Secure the wire harness to the wire tight enough that it will not come undone in the routing process Pull the wire or coat hanger toward the front of the bike with the wires still secured to it Once the wires are pulled far enough to reach the battery they can be removed from the wire coat hanger Take the red power wire and connect it to one end of the Y wire attached to the fuse holder with the butt connectors PIC 8 Slide the wire into the end of the butt connector and crimp The red wire with a black stripe is a power wire that can be used for keyless entry power or interior lighting on the trailer If your trailer DOES NOT need an extra power wire for accessory lighting then DO NOT connect t
6. his to the other Y wire from the fuse holder Wrap the butt connector on the unused red Y wire with RED CONNECTORS NEEDED FOR TRAILER WIRING electrical tape or heat shrink to prevent an unwanted short as it will have power PIC 5 BROWN AND YELLOW WIRES to it all the time and secure it out of harms way Proceed to Step 14 WHEN THE SINGLE RED WIRE WITH THE RING TERMINAL IS CONNECTED TO THE BATTERY IN STEP 15 THE RED WIRE WITH THE BUTT CONNECTOR WILL HAVE POWER AT THE BUTT CONNECTOR MAKE SURE IT IS CAPPED OFF AS IN STEP 13 BEFORE ATTACHING THIS WIRE TO THE BATTERY If your trailer DOES need an extra power wire for accessory lighting Take the red with black stripe power wire and connect it to the end of the second Y wire with the attached butt connector PIC 8 Slide the wire into the end of the butt connector and crimp I PLUG amp PLAY TRAILER WIRING INSTALLATION NOTE If you would like to have keyed power to the red with black stripe wire instead of WARNING STEP 15 STEP 16 STEP 17 ATTENTION Secure all wiring away from any moving parts pinch points or extreme STEP 18 STEP 19 STEP 20 WARNING ATTENTION It is the installer s responsibility to Kuryakyn constant power use a test light to find a keyed wire on the bike and attach this wire to it Be sure to cap off the unused butt connector on the Y wire from the fuse holder as in Step 14 Make sure that
7. ox Take the provided 1 x 2 Hook Strap and the 1 x 2 Loop Strap and place one on the back of the trailer isolation relay and the other on the bike in a good and safe area that is out of harms way Wire up any style connector or 5 4 converter needed for your application TO BATTERY POSITIVE l l l l REFER TO WARNING Re install seat and secure with the mounting hardware that was removed in STEP 13 OR STEP 14 Step 9 Re install the battery cover Reverse Steps 2 to 5 to reassemble the bike BEFORE CONNECTING Check tightness of all fasteners ENSURE PROPER TRAILER AND MOTORCYCLE LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS TRAILER OR MOTORCYCLE LIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY LLEDO GROUND BRAKE ensure that all of the fasteners including preassembled are tightened before operation of the motorcycle Kuryakyn will not issue a RIGHT TURN warranty on components lost due to et ies improper installation Periodic maintenance may be required CAP OFF IF NOT USED REFER TO _ WARNING RUNNING LIGHT STEP 13 AND STEP 14 PAGE PLUG amp PLAY TRAILER WIRING INSTALLATION
Download Pdf Manuals
Related Search