New Cabinet Design with Global VR Steering Board, Sintra
Contents
1. Global VR Part 90633 01 1 Turn off the cabinet and disconnect the AC power cord Remove the Electronics Access Panel from the back of the cabinet to access the Steering Board Disconnect the cables from the existing steering board and connect them to the new board Remove the screws from the mounting feet that secure the existing steering board in place and use them to secure the new board 4 Power on the game Once the Attract Movie starts power cycle the game again to complete the installation 5 After you reboot the game open the Operator Menu and calibrate the force feedback steering Play a game to make sure everything is working properly To Steering Pot 24 VDC In from g Power Supply To Steering Motor USB lt Connector Mounting Foot aa 1of4 Figure 2 GLOBAL VR Steering Board Connections Page 3 of 5 2015 Global VR Inc 040 0271 01 Rev C 3 4 2015 Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Jumper Positions The GLOBAL VR Steering Board requires five 5 jumpers The jumpers are pre installed on the PCB If they are removed the Steering Board will not work properly This picture shows the positions of the jumpers for reference Figure 3 Steering Board Jumper Positions LED Light Strips LED Light strips connect to 12 Volt DC Power and Ground Single Color and or Multi Color Light Strips may be used in your cabinet Single Color LED L2. Strips on page 4 for detailed information on the light strips The Marquee Bezel part NSR AW 14 01 is secured to the cabinet by five 5 14 20 x 34 screws with flat washers The screws mate with T nuts in the cabinet The Logo part NSR AW 14 02 is secured to the Marquee with three 3 14 20 x 2 screws with two fender washers and two plastic spacers Page of 5 10 8 2014 2014 Global VR Inc All Rights Reserved GLOBAL VR and the GLOBAL VR logo are registered trademarks of Global VR Inc Nitro Stunt Racing 2010 Game Seed All other trademarks are the properties of their respective owners Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Sintra Marquee Replacement Important Replacing the Sintra Marquee is a two person job Refer to Figure and note the seven 7 mounting screw locations shown by circles Do the following steps 1 If you only need to replace the logo remove the three 3 14 20 x 2 screws with two fender washers and two plastic spacers that secure the logo to the marquee Remove the logo and use the hardware to install the new logo 2 If you need to replace the entire marquee assembly have a second person support the assembly while you remove the seven 7 44 20 x 34 mounting screws with flat washers shown by the circles in Figure 1 3 Re install the marquee by reversing the removal steps Rear View of Marquee Assembly Mounting Screw Location 1 of 7 O
3. Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation amp Service Manual Document Part O40 0271 01 Rev C Your cabinet has a new design with a Sintra Marquee stand alone TV monitor GLOBAL VR Steering Board and LED strip lights This document supplements the information in your service manual Please refer to this document for information about the marquee monitor cabinet lighting steering board and changes to the audio system Disregard the corresponding sections in your Operation and Service Manual that describe the old style cabinet Table of Contents Software Restoration cccccccccccccecessssssseseseseeeeeeeeeeeees l Sinta Margue tecisrn aa te pit ones niceties net l Sintra Marquee Replacement cceecesecceeeeeeeeeeeees 2 Monitor Replacement osise 2 Steering Board Replacement cseeeeseeeeeeeeeeeeeeeees 3 LED LiCS DSen ne educnn tutor 4 LED Light Strip Replacement ccccceeeeeeeeeeeees 5 Software Restoration If you need to restore software on your game run the Steering Patch Disk after you run the System Recovery Disk SRD Reboot the game and then run the Game Install Disk Refer to your Software Restore Guide document part 040 0272 01 for detailed instructions Sintra Marquee The Sintra Marquee assembly is made up of two pieces the Marquee Bezel and the Logo The marquee is lit by LED Light Strips mounted to the cabinet See LED Light
4. cover or grill 3 Ifthe light has a 4 pin PC power connector disconnect it from the power harness 4 If there is no connector snip the wires and splice them to the wire leads from the new light using a quick connect splicer or preferred splicing method 5 Carefully pull the light strip off of the cabinet it is secured with adhesive Remove the protective backing from the adhesive on the new LED light strip and install it by reversing the removal steps Page 5 of 5 2015 Global VR Inc 040 0271 01 Rev C 3 4 2015
5. ight Strip shown in Figure 4 emits only one color It has one terminal for 12 VDC power and one for ground Multi Color LED Light Strip shown in Figure 5 can be red blue green or a mix depending on which terminal is connected to ground R G or B For white light ground all three color terminals LED light strips can be cut to the length needed but cut only on the white cut line between the terminals as shown in Figure 4 Power and ground leads can be soldered to either end of the LED light strip Secure the LED light strip in place with the double stick tape pre installed on the back of the strip Cut Line i Terminal Solder to 12 VDC Lead Terminal Solder to Ground Lead 12 VDC Connect G Green Desired Color R Red to Ground B Blue For White Light Ground G R amp B Figure 5 Multi Color LED light strip Light Page 4 of 5 040 0271 01 Rev C 3 4 2015 2015 Global VR Inc Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee LED Light Strip Replacement Important To avoid electrical shock unplug the cabinet before servicing lighting components DO NOT replace LEDs with Cold Cathode Fluorescent Lights CCFLs CCFLs draw more current which may cause problems with the driving controls The following are general steps for replacing the LED light strips 1 Turn off the cabinet and disconnect the AC power cord 2 If the light is under a cover remove the screws securing the
6. pening for Ventilation Fan Figure 1 Rear View of Sintra Marquee Monitor Replacement To replace the monitor do the following steps 1 Turn off the cabinet and disconnect the AC power cord 2 Remove the Sintra Marquee Assembly from the cabinet as described on page 2 You can now access the monitor mounting bolts through the opening in the back of the cabinet behind the marquee Disconnect the AC power and DVI cables from the monitor 4 With a second person supporting the monitor remove the four 4 monitor mounting bolts and remove the monitor 5 Replace the monitor by reversing the removal steps Page 2 of 5 040 0271 01 Rev C 3 4 2015 2015 Global VR Inc Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Steering Board Replacement Always turn the cabinet OFF and disconnect the AC power cord before performing any repair work CAUTION GLOBAL VR assumes no liability for any damage or injuries incurred while servicing the cabinet Only qualified service personnel should perform service and installation of cabinet hardware Please read the service instructions before working on the cabinet CAUTION To prevent electrostatic discharge ESD damage handle PCBs by the edges only and use a grounding wrist strap or similar precaution To replace the steering board refer to Figure 2 and do the following steps Important Be sure to use only the Classic version of the Global VR Steering Board
Download Pdf Manuals
Related Search