7 - Greg Cutshaw
Contents
1. PB22 LG01 Empty PD47 PBE1 PD46 PB13 Empty Red Black PB21 Green PB24 PB20 LG02 L013 LD11 BCM Connector PD68 P828 PD74 CHO1 CH02 P580 PF01 PB14 so nen PB12 BCM Connector Driver s side Illuminated Kick Plate Passegner s side Illuminated Kick Plate Page 18 of 18 999G6 MX000 II REV 08 20 102. Tighten all tie wraps Cut excess tie wrap 999G6 MX000 II REV 08 20 10 CHECK BEFORE PART REI NSTALLATI ON 1 Please check that the installation has no problem a confirm the connection of the connectors b confirm wire harness attachment to vehicle O c confirm that there are no loose parts that would cause rattle FUNCTI ON CHECK L 1 Re connect battery negative terminal L 2 Confirm MAXIMA text is illuminated with either Front door in the opened position REI NSTALLATI ON OF REMOVED PARTS 1 All removed vehicle parts have been reinstalled 2 Clean interior of vehicle 3 Verify both kick plates are properly installed with no gaps to body A CAUTION e Use caution when re installing interior components to avoid damage scratch or breaking of mounting clips VEHICLE CHECK 1 Remove all tools from the vehicle 2 Inspect re installed interior trim parts for proper panel fit 3 Turn ignition to ON position L 4 Reset radio presets to the recorded setting 5 Confirm proper radio operation 6 Initialize sun roof and power window operation 7 Turn ignition to OFF position 8 Check and clear trouble codes A CAUTION e During restoring please use caution as not to cause the stacking of the vehicle harness or damage any parts Page 17 of 18 999G6 MX000 II REV 08 20 10 MECH S Green Red Yellow Red gj Pink White amp Sky Blue z 3 White
3. in corner near the driver door pull back carpet toward driver s seat and expose White Carpet Backer Fig 23 Fig 24 24 Bull back Carpet a Starting in corner near the passenger door pull back carpet toward passenger s seat and expose White Carpet Backer Fig 24 Glove Box Handle 25 Secure Wire Harness a Loosely route wire harness under carpet and over transmission tunnel under center console to passenger side b Secure harness with 1 foam tape above white carpet backer Keep wire off of white carpet backer Secure wire along black cable with 2 tie wraps Maintain a 150mm 200mm gap between tie down points Foam Tape Fig 25 Tie Wrap White Carpet Backer Page 13 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue Fig 26 26 Secure Wire Harness a Loosely route wire to passenger side Glove Box Handle kicking plate b Secure wire with 3 foam tapes above white carpet backer Keep wire off of white carpet backer Maintain 150mm 200mm gap between tie down points C At passenger side vehicle harness secure harness with 1 tie wrap Fig 26 27 Secure Wire Harness a Loosely secure harness at connector to vehicle harness with 1 tie wraps b Maintain a 150mm 200mm gap between Glove Box tie down points Fig 27 Black Wiring Cable Tie Wrap Page 14 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue The Procedure below shows the installatio
4. installation instructions Cavity View Cavity 32 Red Black Page 10 of 18 999G6 MX000 II REV 08 20 10 INTERIOR PROCEDURE continue 19 Re Install the BCM to the dash assembly a Secure Harness to BCM Cable with 1 tie wrap Fig 19 b Rotate BCM back into position c Re install 2 Phillips screws 20 Secure Wire Harness Secure Harness to vehicle harness with 2 tie wraps Maintain a 150mm 200mm gap between tie down points Fig 20 Wire going to Driver Foot Well Page 11 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue 21 Secure Wire Harness a Route the wires down to the floor Keep the wire harness to the door side of the Park Brake Keep the wire harness behind the Fuse Block b Secure the wire harness with 2 tie wraps where the harness splits C Maintain a 150mm 200mm gap between tie down points Fig 21 L LAQ Fuse Block Tie Wraps d Ss Park Brake 22 Secure Wire Harness Ls a Route short harness to driver side kicking plate b Secure harness with 2 tie wraps LIENT c Maintain a 150mm 200mm gap between tie down points Fig 22 E Black Wiring Cable Page 12 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue Black Cable 23 Pull back Carpet a Starting
5. tap b Remove protective stub from black wire C Insert the black wire through the non pierce side opening 9 nen d Spread individual strands into a fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure 15 Confirm installation of the tapped wire Fig 15 s a Inspect the tap to ensure correct installation NOTE Avoid putting pressure on the vehicle I5 Straight and evenly spaced all around wire and tap for the rest of the installation ii Tight and no gap iii Test the signal 16 Secure the tap Fig 16 a Secure the tapped wire on the non pierced side to the body of the posi tap with electrical tape 2 2 revolutions b Secure the body to harness where the vehicle wire is being tapped with electrical Nord Existing harness tape 2 2 revolutions harness Page 9 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue 17 Tap the Yellow wire of the Kick Plate Harness to the Sky Blue wire located in cavity 58 of the M18 connector at the BCM Fig 17 a See steps 12 16 for Posi Tap installation instructions Cavity 58 Sky Blue Cavity View Green Red 18 Tap the Black wire of the Kick Plate Harness to the Red Black wire located in cavity 32 of the M18 connector at the BCM Fig 18 See steps 12 16 for Posi Tap
6. Console Lower Panel RH ODNDUAWNE Page 3 of 18 999G6 MXO000 II REV 08 20 10 INTERI OR PROCEDURE L jae Remove the Instrument Panel Side Mask LH a Pull the Instrument Panel Side Mask toward D the door opening to release N Fig 1 b NOTE 274 Repeat on opposite side of vehicle 2 Loosen the Instrument Driver Lower a Remove the fuse panel cover Fig 2a b Remove the 1 Phillips screw behind the fuse panel cover Fig 2b Pull the Instrument Lower Panel rearward in the vehicle to release the 8 clips Fig 2c Remove the harness connector and hose for Instrument Lower Panel optional Page 4 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue WU Fig 3 P F WR TAa Y Page 5 of 18 Front Kicking Plate Outer LH Removal a Start at Rear Edge and pull up by hand May need to use tool to pry up end Fig 3 b There are 4 clips that secure the part NOTE Repeat on opposite side of vehicle Front Kicking Plate Inner LH Removal a Starting at Rear Edge pull up and toward seat using nylon tool b Carefully lift part up moving from rear to front Fig 4 C There are 8 clips that secure the part NOTE Repeat on opposite side of vehicle Remove Dashboard Side Lower Panel a Starting at the floor pull part toward the foot pedals There are 3 clips that secure the part Fig 5 Weather Seal LH Removal b Start at in center of door opening and
7. GENUI NE PARTS INSTALLATION INSTRUCTIONS E DESCRI PTI ON Illuminated Kick Plate APPLI CATI ON Maxima 2010 PART NUMBER 999G6 MX000 KI T CONTENTS Components C thru F in are located in Harness Bag TOOLS REQUI RED e Nylon Removal Tool e Flash Light e Specialty tool for BCM optional e Phillips Head Screw Driver e Soft cloth e Alcohol PRE INSTALLATI ON CAUTI ON NOTES Dealer installation recommended Instructions may refer to Service Manual Installation may require special tools This part is to be installed at a surface temperature no warmer than 65 100F A CAUTION e This accessory must only be installed as specified in these instructions e Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems Page 1 of 18 999G6 MX000 II REV 08 20 10 INSTALLATI ON OVERVI EW Plate Kicking FR RH Plate Kicking FR LH CRI TI CAL STEPS Locate LH mark on back side of part for LH side installation Locate RH mark on back side of part for RH side installation Mis installation can cause impr
8. lor s given in illustration s are for reference only Use location s where color deviates e If a vehicle wire is being used by another accessory and a posi Tap is present tap the accessory wire NOT the vehicle wire 10 Route 3 wire end of harness to the BCM a Use a large cable tie to guide the black wire harness to the cavity where the BCM is housed Loop the wire through the end of the cable tie and pull it up to the BCM cavity Fig 10 Page 7 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue 11 Tap the Red wire of the Kick Plate Harness to the Pink White wire located in cavity 4 of the M17 connector at the BCM Fig 11 a See steps 12 16 for Posi Tap installation instructions Cavity 4 Yellow Red Pink White Cavity View 12 Tap Vehicle Wire Fig 12 a Remove cap slot side from tap body b Slide cap around vehicle wire C Tighten the tap TIGHT with finger pressure NOTE Do not re use the tap for subsequent re installation 13 Inspect the tap to ensure correct installation Fig 13 NOTE Avoid putting pressure on the vehicle wire and tap for the rest of the installation i Straight and evenly spaced all the way around ii Tight and minimize gap wire jacket should be crushed Page 8 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue 14 Tap accessory wire Fig 14 a Remove tap non pierce side from
9. n for LH Side Repeat Procedure for RH side Front RH amp LH parts are not interchangeable 28 Prepare Harness Connector a Remove tape wrap from harness Fig 28 Tape Wrap 29 Install Front Kicking Plate Outer LH a Clean vehicle body with alcohol and allow to dry b Starting from the front align clips on the kicking plate with the body holes Fig 29 NOTE Be careful not to damage clips during installation 30 Install Front Kicking Plate Outer LH a Place Kick Plate over holes b Cover top of the kick plate with cloth to prevent damage C Press down directly above each clip to engage Push to snap Fig 30 NOTE Be careful to install left kicking plate to left side of vehicle Mis installation can cause improper fit Page 15 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue Connectors Tie Wrap Kick Plate Controller Fig 31a Tie Wrap Harness Retainer Fig 31b Excess Harness The Procedure below shows the installation for LH Side Repeat Procedure for RH side 31 Connect the Kicking Plate to the Harness a b Page 16 of 18 Connect the Connectors Fig 31a Make sure that wiring passes over door flange and forward of the black plastic harness retainer Fig 31a Secure harness with 2 tie wraps Maintain a 150mm 200mm gap between tie down points Fig 31a If you have excess harness loop the extra length to the vehicle harness with 1 tie wrap Fig 31b
10. oper fit e Follow posi tap instructions Page 2 of 18 999G6 MX000 II REV 08 20 10 VEHICLE PREPARATION A CAUTION e Dealer Installation Recommended I nstructions refer to steps described in Service Manual e Please read these instructions carefully before installing this product for correct installation e Please DO NOT use or install the part in ways other than what is described in this instruction manual e If problem occurs during installation please contact Nissan dealer where you purchased the product 1 Apply Park Brake 2 Make sure the shift lever is engaged in P position 3 Record customer Radio Presets 4 Use seat and floor protection 5 Open hood of the vehicle 6 Disconnect the negative battery terminal to prevent short circuits during installation 7 This part is to be installed at a vehicle body surface temperature of 65 100 F A CAUTION e Take care not to scratch or damage any component during the removal or re installation process e Trim pieces found to have witness marks or broken clips are not to be re installed Removal Sequence Instrument Panel Side Mask LH Instrument Driver Lower Front Kick Plate Outer LH Front Kick Plate Inner LH Dashboard Side Lower Panel LH Center Console Lower Panel LH Instrument Cluster Trim Panel Instrument Cluster BCM 10 Front Kick Plate Outer RH 11 Front Kick Plate Inner RH 12 Dashboard Side Lower Panel RH 123 Center
11. pull up C Pull seal away from the body between the b pillar lower and the side mask Fig 5 NOTE Repeat on opposite side of vehicle 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue 6 Remove the Center Console Lower Panel LH a Pull the Center Console Lower Panel toward the foot pedals There are 3 clips that secure the part Fig 6 NOTE Repeat on opposite side of vehicle 7 Remove the Instrument Cluster Trim Panel a Remove the 2 Phillips screws at the lower left and right corners Fig 7 b Pull the panel towards the driver s seat and free from the Instrument Panel NOTE Do not disconnect the switches Rotate the panel to the right out of the way 8 Remove the Instrument Cluster a Remove the 3 Phillips screws One on top and one at the left and right lower corners Fig 8 b Do Not disconnect the Cluster Rotate the assembly to the right and up out of the way NOTE Disconnect a white electrical connector on the left side of the cluster if necessary to allow the assembly to rotate Page 6 of 18 999G6 MX000 II REV 08 20 10 INTERI OR PROCEDURE continue Remove the BCM from the dash assembly a Remove the 2 screws securing the BCM bracket to the dash assembly Fig 9 b Rotate BCM to access connectors Screw NOTE There may be special one way screws used to secure the BCM to the vehicle Use a Grab it or other tool to remove the special screws A CAUTION e Co
Download Pdf Manuals
Related Search