Home

Digital Projector X62

1. disassemble short recharge or expose to fire or high temperature Do not carry batteries loose in your pocket or purse Avoid eye and skin contact in the event that battery would leak Do not mix used and new batteries To reduce the risk associated with intense visible light Avoid looking directly into the projector lens while the lamp is on Important Note the lamp breaks soon after the first time it is used it is possible that there are electrical problems elsewhere besides the lamp If this happens contact your local dealer or a service representative 3M 2006 3M Multimedia Projector X62 Product Safety Guide 11 3M Digital Projector X62 y Note For maximum lamp life do not strike or drop improperly handle or scratch the lamp glass Also do not install an old or previously used lamp l Remove lamp access door Loosen the lamp door screw marked by arrow 1 and then slide the lamp door to the side to remove it 2 2 Retaining screws Use a screwdriver to unscrew the lamp module retaining screws marked by arrow 3 Note All lamp module screws must be loosened These screws are self containing screws that cannot be removed from the lamp module or access door 3 Remove lamp module Slowly pick up the lamp module by the handles 4 4 Insert lamp module Carefully insert 4 the new lamp module Ensure that it 1s fully seated Tighten the lamp module retaining screws 3 to secure the lam
2. 3M Digital Projector X62 Digital Projector X62 Product Safety Guide X62 Projecteur multimedia Guide de S curit de Produit X62 Multimedia Projektor Sicherheitsanleitung des Ger ts X62 Proyector de Multimedia Guia de Seguridad del Producto X62 Proiettore Multimediale Guida di Sicurezza del Prodotto X62 Multimedia Projector Veiligheidsgids op Product X62 Projector dos Multimedia Guia da Seguran a de Produto X62 Multimedia Projector Bruksanvisning f r Produktsakerhets X62 SUA PL 248 e X62 BE kA X62 Multimediaprojektori Laitteen turvaohjeet 3M Digital Projector X62 2 3M Multimedia Projector X62 Product Safety Guide 3M 2006 3M Digital Projector X62 Table of Contents ENGLISH SLEA LUOEDD 1A EI uuu 5 ol d teen 9 Ji sist eins nsn Sus ease E SSS SS SS S E SSS A 10 li ll E 13 3M 2006 3M Multimedia Projector X62 Product Safety Guide 3M Digital Projector X62 4 3M Multimedia Projector X62 Product Safety Guide 3M 2006 3M Digital Projector X62 Safety Information Read understand and follow all safety information contained in the Product Safety Guide and in the Operator s Guide prior to using the 3M Digital Projector Service personnel must also read and understand the safety information contained in the Service Manual Retain these instructions for future reference Inte
3. AMPENABDECKUNG UND DIE LAMPENEINHEIT ZU ENTFERNEN LOSEN SIE NIE EINEDER SCHRAUBEN OHNE PFEILMARKIERUNG ALTO VOLTAGGIO ALTA TEMPERATURA ALTA PRESSIONE SE SI DEVE SOSTITUIRE LA LAMPADA SPEGNERE IL PROIETTORE ESTRARRE LA SPINA DEL DI ALIMENTAZIONE DALLA PRESA DELLA RETE ELETTRICA PRIMA DI SOSTITUIRE LA LAMPADA ASPETTARE CHE SI RAFFREDDI ALMENO 45 MINUTI A TOCCARE LA LAMPADA QUANDO CALDA SI CORRE IL RISCHIO DI SCOTTARSI LA MANO UNA LAMPADA AD ALTA PRESSIONE QUANDO E CALDA PUO ESPLODERE SE NON MANEGGIATA CORRETTAMENTE CONSULTARE LE ISTRUZIONI L USO SVITARE SOLAMENTE LE VITI INDICATE CON UNA FRECCIA PER RIMUOVERE LO SPORTELLO DELLA LAMPADA E LA LAMPADA STESSA NON ALLENTARE MAI NESSUN ALTRA VITE ECCETTO QUELLE INDICATE CON LA FRECCIA ALTO VOLTAJE ALTA TEMPERATURA ALTA PRESION PARA REEMPLAZAR LA LAMPARA APAQUE EL PROYECTOR Y RETIRE EL CABLE DE ALIMENTACION DEL TOMACORRIENTE ANTES DE REEMPLAZAR LA LAMPARA ESPERE HASTA QUE LA LAMPARA ENFRIE AL MENOS UNOS 45 MINUTOS TOCA LA LAMPARA CUANDO ESTA CALIENTE PUEDE QUEMARLE LAS MANOS LA LAMPARA DE ALTA PRESION CUANDO ESTA CALIENTE PUEDE EXPLOTAR SI NO ES MANIPULADA DEBIDAMENTE CONSULTE LA GUIA DEL USUARIO DESTORNILLE SOLO LOS TORNILLOS MARCADOS CON UNA FLECHA m gt PARA QUITAR LA TAPA DE PROTECCI N DE LA L MPARA Y L EXTRAER LA LAMPARA CUIDE DE DESTORNILLAR SOLO LOS TORNILLOS MARCADOS CON LA FLECHA 3M Multimedia Projector X62 Product S
4. MP WAIT UNTIL THE LAMP BECOMES COOL FOR MINIMUM 45 MINUTES TOUCHING THE LAMP WHEN IT IS HOT MAY CAUSE A BURN ON YOUR HAND HIGH PRESSURE LAMP WHEN HOT MAY EXPLODE IF IMPROPERLY HANDLED REFER TO USER S GUIDE LOOSEN THE SCREWS MARKED WITH AN ARROW mm TO REMOVE THE LAMP DOOR AND LAMP UNIT NEVER TOUCH ANY SCREWS WITHOUT THE ARROW MARK HAUTE TENSION HAUTE TEMPERATURE HAUTE PRESSION ETEIGNEZ LE PROJECTEUR ET DEBRANCHEZ LE CORDON D ALIMENTATION DE LA PRISE AVANT DE REMPLACER L AMPOULE LAISSEZ REFROIDIR L AMPOULE AU MOINS 45 MINUTES AVANT DE LA RETIRER POUR NE VOUS BRULER LES MAINS EN CAS DE MAUVAISES MANIPULATION LES AMPOULES HAUTE PRESSION RISQUENT D EXPLOSER QUAND ELLES SONT CHAUDES CONSULTER LE MODE D EMPLOI RETIREZ SEULEMENT LES VIS MARQUEES AVEC UNE FL CHE m gt POUR ENLEVER LA PORTE DE LA LAMPE ET LA LAMPE ELLE MEME NE RETIREZ JAMAIS LES VIS NON MARQUEES D UNE FLECHE HOCHSPANNUNG HOCHTEMPERATUR HOCHDRUCK BEIM AUSWECHSELN DER GLUHLAMPE DEN PROJEKTOR AUSSCHALTEN UND DAS NETZKABEL AUS DER WANDSTECKDO SE ABZIEHEN VOR DEM AUSWECHSELN DER GLUHLAMPE WARTEN BIS SICH DIE LAMPE ABGEKUHLT HAT MINDERSTENS 45 MINUTEN DARAUF ACHTEN DAB DIE GLUHLAMPE NICHT BERUHRT WIRD DA DIES VERBRENNUNGEN VERURSACHEN KANN BEI UNSACHGEMASSER BEHANDLUNG KANN DIE UNTER HOHEM DRUCK STEHENDE BIRNE EXPLODIEREN SICH AUF DIE BEDIENUNGSANLEITUNG BEZIEHEN ENTFERNEN SIE NUR DIE MIT EINEM PFEIL gt MARKIERTEN SCHRAUBEN UM DIE L
5. afety Guide 3M Digital Projector X62 Lamp Lamp Operation The following symptoms may indicate a lamp in need of replacement e LAMP indicator lights up red WARNING e To reduce the risk associated with environmental contamination due to mercury in the projection lamp Dispose of lamp cartridge in accordance with applicable federal state and local regulations The lamp in this product contains mercuy Dispose of projection lamp in a manner that is consistent with your local hazardous waste regulations for mercury For recycling and disposal information contact your respective governmental agencies In U S contact the Electronic Industries Alliance at www lamprecycle org In Canada contact 1 800 362 3577 Canada Display Lamp Operation Hours To determine the lamp operation hours follow these steps 1 While the projector is running press the MENU button on the remote control Choose the OPTION using Y button and press P gt button or the ENTER button Choose the LAMP TIME using the V button 2 The operating time of the lamp will be displayed The lamp time is the time counted after the last resetting Vv Note Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp Reset Lamp Hours 1 Press the MENU button to display a menu Only when the EASY MENU has appeared please perform the next step 2 2 Point at the Go To Advan
6. art 15 of the FCC Rules which are designed to provide reasonable protection against such interference when operated in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help INSTRUCTIONS TO USERS This equipment complies with the requirements of FCC equipment provided that the following conditions are met The cables may have to be used with the core set to the projector side Use the cables which are included with the projector or specified Note Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment EEC STATEMENT This machine was tested against the 89 336 EEC European Economic Community for EMC Electro Magnetic Compatibility and fulfills these requirements Video Signal Cables Double shielded coaxial cables FCC shield cable must be used and the outer shield must
7. be connected to the ground If normal coaxial cables are used the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation Video Inputs The input signal amplitude must not exceed the specified level PATENTS TRADEMARKS amp COPY RIGHTS IBM is a registered trademark of International Business Machines Corporation Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer Inc Microsoft and Windows 95 amp Windows 98 are registered trademarks and Windows and Windows for Workgroups are trademarks of the Microsoft Corporation Toshiba is a registered trademark of Toshiba Corporation Kensington 15 a trademark of Kensington Corporation All other products are trademarks or registered trademarks of their respective companies 3M 2006 3M Multimedia Projector X62 Product Safety Guide 13 3M Digital Projector X62 Important Notice All statements technical information and recommendations related to 3M s products are based on information believed to be eliable but the accuracy or completeness is not guaranteed Before using this product you must evaluate it and determine if it is suitable for your intended application You assume all risks and liability associated with such use Any statements related to the product which are not contained in 3M s current publications or any contrary statements contained on your purchase order shall have no force or effect unless expres
8. ce Menu in the menu using V A button then press the gt button 3 Point at the OPTION in the left column 01 the menu using V A button then press the button 4 Point at TIME using V A button then press button A dialog will appear 5 Press the A button to select RESET on the dialog It performs resetting the lamp time 10 3M Multimedia Projector X62 Product Safety Guide 3M 2006 3M Digital Projector X62 Replacing Lamp The glass lamp used in this projector contains small amounts of mercury and operates at high pressure and at high temperature and may unexpectedly shatter Each lamp has a different lifetime and can fail in different ways including a rupture with a loud bang or simply burn out In the event of a lamp rupture be sure to follow the instructions WARNING To reduce the risk associated with exposure to hazardous voltage Disconnect power cord when the projector is not in use during lamp replacement and while cleaning Do not remove any screws other than those specified in the lamp replacement instructions Do not attempt to service the projector there are no user serviceable parts other than the lamp cartridge inside the projector Contact a 3M authorized service provider for service To reduce the risk associated with hot surface of lamp cartridge Unplug the projector from the electrical outlet and allow the lamp to cool for 45 minutes before replaci
9. dify this projector Do not attempt to service the projector there are no user serviceable parts other than the lamp cartridge inside the projector Contact a 3M authorized service provider for service Do not allow water or other liquids to enter the projector To reduce the risk associated with environmental contamination due to mercury Dispose of lamp cartridge in accordance with applicable federal state and local regulations To reduce the risk associated with exposure to hazardous voltage and or fire Replace power cord if damaged Contact a 3M authorized service provider if the projector becomes damaged Use 8 grounded extension cord with a rating at least equal to that of the projector Connect this projector to a grounded outlet To reduce the risk associated with hazardous voltage impact tripping and intense visible light Do not use this projector around unsupervised children To reduce the risk associated with hot surface of lamp cartridge Unplug the projector from the electrical outlet and allow the lamp to cool for 45 minutes before replacing the lamp To reduce the risk associated with a ruptured lamp Always handle the fragile lamp module with care Remove the projector from the ceiling or wall mount before replacing the lamp Use care when replacing the lamp module in the event of a lamp rupture small glass particles and small amounts of mercury may be present Ventilate the area w
10. here the lamp rupture occurred Wear safety goggles and gloves when cleaning up ruptured lamp debris Carefully collect the ruptured lamp debris in a closed container and dispose of the container and the expired lamp module in accordance with federal state and local regulations Wash your hands thoroughly after handling ruptured lamp debris Replace the lamp module when the lamp replacement message appears Never replace the lamp module with a previously used lamp module 3M Multimedia Projector X62 Product Safety Guide 3M 2006 3M Digital Projector X62 A CAUTION To reduce the risk associated with explosion and or chemicals from a leaking battery Use only with battery type AA or equivalent Orient the battery s plus and minus terminals of the batteries according to the markings found on the remote control Do not leave the battery in the remote for an extended period of time Do not heat disassemble short recharge or expose to fire or high temperature Do not carry batteries loose in your pocket or purse Avoid eye and skin contact in the event that battery would leak Do not mix used and new batteries To reduce the risk associated with the impact of a falling projector Use only the 3M brand wall ceiling mounting hardware kit if wall or ceiling mounting is desired Installation of the 3M wall ceiling kit must only be performed by qualified personnel Adhere strictly to the proper insta
11. ironment Product Warranty is void if used outside of the following circumstances e 100V 240V AC 50 60 Hz e 16 to 29 C 60 to 85 F 10 80 RH without condensation e 0 1828m 0 6000 feet above sea level The ambient operating environment should be free of airborne smoke grease oil and other contaminates that can effect the operation or performance of the projector d The warranty will be void if you repair or modify the 3M Digital Projector or you otherwise damaged the product due to misuse neglect mishandling or other abuse LIMITATION OF LIABILITY THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS 3M SHALL NOT BE LIABLE FOR ANY DAMAGES DIRECT CONSEQUENTIAL OR INCIDENTAL ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT Important The above warranty shall be void if the customer fails to operate product in accordance with 3M s written instructions This warranty gives you specific legal rights and you may have other rights which vary from state to state FCC STATEMENT CLASS B This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class B computing device pursuant to Subpart B of P
12. llation procedure as outlined in the installation instructions when installing the 3M wall ceiling kit Always operate the unit on a flat sturdy and horizontal surface To reduce the risk associated with intense visible light Avoid looking directly into the projector lens while the lamp is on To reduce the risk associated with tripping and or impact Position the power cord and data cable so that they cannot be tripped over 3M 2006 3M Multimedia Projector X62 Product Safety Guide 7 3M Digital Projector X62 Important Note 1 2 10 11 12 13 14 15 Always open the lens shutter or remove lens cap when the projection lamp is on To avoid premature lamp failure do not change the mounting position of the projector desktop ceiling mount or ceiling desktop mount and continue to use the same lamp To avoid reduced lamp life do not touch projection lamp with bare fingers To avoid reduced image quality do not touch projection lens or other internal optical components Do not use detergents chemicals or any spray liquids for cleaning this unit other than those referred to in the Operators Guide For maximum lamp life do not strike or drop improperly handle or scratch the lamp glass Also do not install an old or used lamp Keep air filter clean Refer to the cleaning instructions contained in the Operator s Guide Keep all ventilation openings free of any obstructions I
13. n some countries the line voltage is NOT stable This projector is designed to operate safely within a bandwidth of 100 to 120 volts 220 to 240 volts 50 to 60 Hz 10 but could fail if power drops or surges of 10 volts occur In these high risk areas it is recommended to install a power stabilizer unit Do not block intake or exhaust air vents This will cause the projector to over heat and shut down Do not place the projector in direct sunlight or near a hot object such as a heater To prevent damaging the projector always hold the projector whenever using the elevator buttons to adjust the elevator feet Use the accessory cable or a designated type cable for the connection Some cables have to be used with core set A too long cable may cause certain picture degradation Please consult with your dealer for details For cables that have a core only at one end connect the core to the projector Make sure that you connect devices to the correct port Incorrect connection may result in malfunction and or damage to the device and or projector Do not place the projector in the side front rear up position except care of the air filter 3M Multimedia Projector X62 Product Safety Guide 3M 2006 3M Digital Projector X62 3M 2006 Product Safety Labels HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WHEN REPLACING THE LAMP TURN OFF THE PROJECTOR AND PULL OUT THE POWER CORD FROM THE RECEPTACLE BEFORE REPLACING THE LA
14. nded Use The 3M Digital Projector X62 was designed built and tested for use indoors using 3M brand lamps 3M brand ceiling mount hardware and nominal local voltages This projector is not intended for household use or use by children The use of other replacement lamps outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and or create a potentially unsafe operating condition Explanation of Signal Words and Symbols in Safety Labels and Instructions WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Warning Hazardous Voltage Warning Hazardous High Temperature Warning High Pressure Attention Refer to Safety Instructions in Guides 3M 2006 3M Multimedia Projector X62 Product Safety Guide 5 3M Digital Projector X62 WARNING To reduce the risk associated with choking Keep the battery and battery holder away from children and pets To reduce the risk associated with exposure to hazardous voltage Disconnect power cord when the projector is not in use during lamp replacement and while cleaning Do not remove any screws other than those specified the lamp replacement instructions Do not store or operate this projector in wet environments Donot mo
15. ng the lamp To reduce the risk associated with a ruptured lamp Always handle the fragile lamp module with care Remove the projector from the ceiling or wall mount before replacing the lamp In the case of a lamp rupture small glass particles could fall out when the lamp door is opened or the projector is tilted Use care when replacing the lamp module in the event of a lamp rupture small glass particles and small amounts of mercury may be present Ventilate the area where the lamp rupture occurred Wear safety goggles and gloves when cleaning up ruptured lamp debris Carefully collect the ruptured lamp debris in a closed container and dispose of the container and the expired lamp module in accordance with federal state and local regulations Wash your hands thoroughly after handling ruptured lamp debris Replace the lamp module when the lamp replacement message appears Never replace the lamp module with a previously used lamp module To reduce the risk associated with environmental contamination due to mercury Dispose of lamp cartridge in accordance with applicable federal state and local regulations To reduce the risk associated with explosion and or chemicals from a leaking battery Use only with battery type AA or equivalent Orient the battery s plus and minus terminals of the batteries according to the markings found on the remote control Do not leave the battery in the remote for an extended period of time Do not heat
16. p module place Optional Lamp 78 6969 9875 2 Contact 3M Customer Service Slide the lamp door 2 back in place and firmly fasten the lamp door a screw 1 y Note Reset the lamp operation hours See Reset Lamp Hours for details 3 Screws 2 Lamp access door 12 3M Multimedia Projector X62 Product Safety Guide 3M 2006 3M Digital Projector X62 Warranty LIMITED WARRANTY This product will be free from defects in material and manufacture for a period of three 3 years from the date of purchase subject to the following limitations The following are exclusions to the above listed warranty or are subject to a different warranty as set forth below a The warranty for lamps that are included as original equipment in the projectors is for parts only and is effective for a period of 90 days after the date of purchase of the projector or 180 hours of lamp usage whichever occurs first b The warranty period for LCD panels including polarizers is either 3 years from the date of purchase of the projector or 2500 hours of projector usage whichever occurs first If within 3 years from the date of purchase of the projector the LCD panel requires replacement and is otherwise eligible for warranty coverage but the projector has exceeded 2500 hours of usage the 3M warranty will cover the cost of labor but not the cost of parts that require replacement c 3M Digital Projectors are designed to operate in a typical indoor env
17. sly agreed upon in writing by an authorized officer of 3M Let us help you make the most of your next presentation We offer everything from presentation supplies to tips for better meetings And we re the only transparency manufacturer that offers a recycling program for your used transparencies For late breaking news handy reference and free product samples call us toll free in the continental United States and Canada 24 hours a day or visit our Internet Website http www 3m com meetings e mail meetings mmm com Sx 800 328 1371 3M Austin Center 3M Canada 3M Mexico S A de C V 3M Europe Building A145 5N 01 P O Box 5757 Apartado Postal 14 139 Boulevard 86 6801 River Place Blvd London Ontario Mexico D F 07000 95006 Cerge Pontoise Cedex Austin TX 78726 9000 N6A 1 Mexico France Litho in China 3M 2006 QR68031 78 6970 9457 7 Rev

Digital Projector X62

Contents

Download Pdf Manuals

Related Search

Related Contents