Home

GFK2789D WV3 HW Ref Manual

1. Figure 14 Wolverine II Handle Option GFK 2789D October 2014 13 Chapter 2 Getting Started Wolverine III Agency Approvals and Regulations 14 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 3 Connectors and Cabling This chapter describes the connector layout and cabling on Wolverine III industrial computers Power and communication connectors are described in this section Connectors are located on the back 1 0 plate When operating the unit in a hazardous area all cables to the I O plate must be fed through the glands on the Gland Plate PS 2 Keyboard PS 2 Mouse port Four serial ports COM1 COM2 COM3 COM4 Parallel port Four USB 2 0 ports One USB connector optional in Gland Plate Two Ethernet 10 100 1000baseT ports RJ 45 Remote PWR BIN Horn Output VGA port Audio Mic Line Out Power AC or DC WLAN beside UO plate The grade of protection by the enclosure is determined by its gas tightness Not only the cable gland needs to be sealed but also the cable itself This only needs to be considered for cables that end in the ATEX Zones Input and output wiring methods and cable types must be in accordance with ATEX Zone 2 and Class 1 Division 2 wiring methods in accordance with the authority having jurisdiction and the manufacturer recommendatio
2. Chapter 2 Getting Started Warning This equipment is suitable for use in ATEX Zone 2 Class 1 Division 2 or non hazardous locations only WARNING EXPLOSION HAZARD DO NOT DISCONNECT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOWN TO BE FREE OF IGNITIBLE CONCENTRATIONS AVERTISSEMENT RISQUE D EXPLOSION AVANT DE DECONNECTER L EQUIPEMENT COUPER LE COURANT OU S ASSURER QUE L EMPLACEMENT EST DESIGNE NON DANGEREUX WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR USE IN DIVISION 2 AVERTISSEMENT RISQUE D EXPLOSION LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CE MATERIEL INACCEPTABLE POUR LES EMPLACEMENTS DE DIVISION 2 Enclosure Cover Warning Explosion hazard Do not remove cover unless area is known to be non hazardous This warning applies to any removable cover on the unit Service Lid Gland Plate etc Input and output wiring methods and cable types must be in accordance with ATEX Zone 2 or Class 1 Division 2 wiring methods and in accordance with the authority having jurisdiction All cable glands must be equipped with a cable or with a blind plug Antenna Warning Explosion hazard Do not remove or install antenna unless area is known to be non hazardous Only isolated antennas are allowed where the inner part is not touchable after mounting If the case is damaged or if the touch cover sheet is broken or perforated the unit must be taken out of service and repaired
3. Dimensions 12 Embedded controller EC 33 advanced configuration and power interface ACPI 33 environmental control 33 heat up times 33 monitoring interface 33 power and heater LEDs 34 October 2014 Environmental and Mechanical Specifications 3 Environmental control thermal 33 Environmental specifications Wolverine Ill 3 Ethernet LAN ports 29 Ex ic USB port 28 ExpressCard devices installing 43 Fans replacing 47 Features Wolverine Ill 2 Field maintenance 35 components 36 inspection 35 Field serviceable components 36 Floor Stand 5 Front plate 45 Fuses replacement 38 Gland Plate installing after cable connection 22 removing to install cables 20 repair 37 Retention Screw Replacement 38 torque values for glands 21 38 Government regulations 49 Handle 19 Hard disk drive HDD 43 Heat up times 33 Horn output 30 I O Plates IOPs 22 Indicators 4 5 Inspection routine maintenance 35 unpacking 7 Installation Wolverine IIl industrial display computer 8 Intrinsically Safe Ex ic USB Port 28 Intrinsically Safe keyboard WVKBUSBOO1A 5 Index Keyboard Intrinsically Safe WVKBUSBOO1A 5 PS 2 port 31 Keyboard Tray 19 LEDs 4 5 HTR heater 34 PWR power 34 Maintenance 35 inspection 35 Mechanical specifications 3 Monitoring interface 33 Mounting Floor 17 Location 11 options 14 floor mount 14 panel 14 wall 14 Panel 14 Wall and Desktop V
4. Gland Gland 2X 2X D 6 mm 12 mm D 4 mm 8 mm IO 0 236 inch 0472 inch D 0 157 inch 0315 inch Wlan antennas 2x SMA M3 captive screw 15x use PH1 screw driver 0 8 Nm 7 lbf in A Do not lock USB Gland Plate Figure 18 Gland Plate Warning Modification of the Gland Plate invalidates enclosure protection and the ATEX certification 5 4 1 Removing the Gland Plate To remove the Gland Plate GFK 2789D 1 Loosen the 15 captive screws that secure the Gland Plate to the unit as shown in Figure 18 Disengage the Gland Plate from the unit being careful not to strain the cable connecting the USB gland to the USB1 port October 2014 33 Chapter 5 Field Maintenance Wolverine II Agency Approvals and Regulations 5 4 2 Routing Cables through the Gland Plate All plugs connected to the 1 0 Plate must be protected from unplugging by shock and vibration Use securing means of the plugs when available and glue all others where securing means are not available Torque Values for Cable Glands Torque values for cable glands are determined by gland type cable type and diameter For torque values refer to the manufacturer s instructions for the cable glands 5 4 3 Installing the Gland Plate The Gland Plate kits WV3SGLANDPLO and WV3SGLANDPL1I include e aGland Plate with all connectors and cable glands e the O ring required for
5. October 2014 3 Chapter 2 Getting Started Wolverine III Agency Approvals and Regulations ATEX Specific Conditions of Use Symbol X The equipment avoids electrostatic charging that occurs during standard handling such as wet cleaning and touching But charging processes directly beside the equipment must be avoided The device shall be used in areas where the risk of mechanical danger is low The intended mounting orientation is that the screen is landscape and perpendicular to the floor The equipment may lean backward or forward by an angle of 45 The protection level of the device is maintained by the gas tightness of its case After installation and service all lids and openings need to be closed as described within this manual ATEX Markings for Hazardous Area Approvals Il 3G Ex nC ic IIC T4 Gc X 40 C lt Ta lt 60 C Definitions of Markings for Hazardous Area Approvals Ex Protection against ignition of explosive atmospheres lI Group Il 3G Category 3 for Gases Zone 2 Equipment Ex Protection against ignition of explosive atmospheres nC Generol protection concept Sealed Device ic Second protection concept Intrinsically safe circuits EPL Equipment Protection Level c IIC Groupll subdivision C a typical gas is hydrogen T4 Maximum surface temperature is 135 C Gc Protection for explosive gases Equipment Protection Level EPL c X specific conditions of use symbol xX 2 3 3
6. RE EE SA E EN E E A EN EESE S E E S E S EOE a i lt 8 mm 0 3 in Figure 6 Wolverine III Panel Cutout 8 Wolverine IlI Industrial Display Computer Hardware Reference Manual GFK 2789D GFK 2789D Chapter 2 Getting Started Instructions for use of the WV3ACCPANLMT Panel Mounting Kit The WV3ACCPANLMT Panel Mounting Kit Includes eight brackets with frames one WV3SPPMOUNTO gasket 1 Place the gasket on the unit by sliding the gasket over the back of the unit and positioning it behind the front panel faceplate 2 Attach the brackets to the unit as shown in Figure 7 below 3 Insert the Wolverine III into the cutout and open the set screws on the rear of the brackets 4 Open the brackets 90 angle between bracket and frame and slightly tighten the set SCrews 5 After all screws have been slightly tightened and the Wolverine III is adjusted to the final position tighten all the set screws to a final torque of no more than 1 5 Nm 13 3 Ibf in 387 15 236 2 10 0 079 0 394 THICK PANEL metric size 25 mm hexagon socket wrench required Figure 7 Wolverine III Panel Mount Option October 2014 9 Chapter 2 Getting Started Wolverine III Agency Approvals and Regulations 2 3 8 Wall and Desktop Mounting VESA Mount The Video Electronics Standards Association VESA publishes the Mounting Interface Standard the VESA MIS colloquially known as the VESA mo
7. into the retainer body 7 Continue turning until the screw threads are past the retainer ring and the head is flush with the retainer body as shown in Figure 22 Figure 22 Threading the retention screw through the retainer ring 36 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 5 Field Maintenance 5 6 Service Lid The Service Lid is accessed from the left hand side of the unit It allows access to the SSD ExpressCard slot desiccator and battery The lid desiccator and SSD carrier are integrated as one unit Mee Bee Desiccator p saturation indicator on top Lef oe WA Express Card 34mm or 54mm module E Tea 2 5 SSD or HDD Figure 23 Service Lid 5 6 1 Removing the Service Lid Caution To avoid damage to this assembly when removing the Service Lid turn each screw in sequence a maximum of two turns counterclockwise Continue loosening screws in sequence two turns at most until all four screws are loose Use a PH1 screwdriver to turn the screws A a 2 turns Figure 24 Service Lid screws GFK 2789D October 2014 37 Chapter 5 Field Maintenance Wolverine II Agency Approvals and Regulations 5 6 2 Installing the Service Lid Before reinstalling the service lid ensure that the O ring is in its groove and is not damaged Further ensure that the flange of the wrapper and the service lid are clean Apply a thin layer of DC
8. provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and If not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Any changes or modifications to the product or installation that are not expressly approved by GE Intelligent Platforms could void the user s authority to operate the equipment under FCC rules 46 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Index GFK 2789D Accessories 5 Advanced configuration and power interface ACPI 33 Agency approvals 48 ATEX conditions of use 9 Audio Mic Line Out 32 Bonding 22 38 Cleaning mode Wolverine Ill 4 Components field serviceable 36 fans 47 front plate 45 O rings 37 Connectors and cabling 20 AC units overview 22 Audio 32 DC units overview 24 power 24 Ethernet LAN ports 29 Ex ic USB port 28 horn output 30 printer port LPT1 26 PS 2 mouse and keyboard 31 remote PWR BIN 32 RS 422 and RS 485 26 serial communication ports 26 shielding 27 USB ports 27 VGA port 31 WLAN port 30 Control drawing 28 Controls 4 Desiccant 42
9. 0 C 20 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 3 Connectors and Cabling 3 3 Printer Port LPT1 A 25 pin D type female printer port connector is located on the back 1 0 plate and labeled accordingly In order to provide higher EMC immunity and maintain CE Mark compliance the LPT cable must be shielded e In Im Is sens In fase a ootesk7 men Jose OOS 3 4 Serial Communication Ports Four COM ports 1 4 are available on the back 1 0 plate COM1 and COM2 can be configured for RS 232 or RS 422 RS 485 operation The preselected mode is RS 232 To select COM1 or COM2 operating mode enter BIOS and go to the Advanced gt Super IO Configuration gt Serial Port Mode menu COM3 and COM4 are used as RS 232 interfaces Transient protection is enhanced on the COM3 and COM4 ports Therefore those ports should be used first 12345 00 70 00 oo0o0o 6789 Table 15 COM Port Pin Assignments for RS 232 Pin Assignment e Lompen OOOO LE escorte send o Jupe SSSSCSC S S S S S S 3 4 2 RS 422 and RS 485 Operating Mode COM1 and COM2 can be selected as RS 422 RS 485 through BIOS GFK 2789D October 2014 21 Chapter 3 Connectors and Cabling Wolverine III Agency Approvals and Regulations Table 16 COM Port Pin Assignments for RS 422 RS 485 mi Assignment 5 en ana round e riseg SSCS a _ ctse clortoSend poste SSS 5 fers onto Send negative 3 4 3 Shielding I
10. 3 4 4 Tasks of the Embedded Controller The embedded controller EC acts as an environmental controller to ensure safe operation conditions as an ACPI embedded controller to show conditions to the operating system provides the ability to monitor and change many parameters Environmental Control The Wolverine III is prevented from starting until all thermal requirements are fulfilled With its integral heater system the Wolverine III has the capability to heat and cool specific parts of the system to reach internal requirements Heat up times System heat up times depend on the starting temperature Start up from 20 C will last less than 3 minutes Start up from 30 C will last less than 7 minutes Start up from 40 C will last less than 19 minutes If an unsupported temperature is measured the EC will remove power to the whole system to ensure safe behavior Advanced Configuration and Power Interface ACPI The ACPI EC operates with an ACPI capable operating system and includes five thermal zones te SYSTEM 2 DISPLAY 3 HDD 4 HDA 5 WLAN For these zones the operating system can display the temperatures as well as reacting at critical thresholds with an operating system specific behavior for example emergency shutdown GFK 2789D October 2014 29 Chapter 4 Embedded Controller Wolverine IIl Agency Approvals and Regulations 4 5 Power and Heater LEDs The following table of shows the PWR and HTR LED co
11. 4 silicon grease from DOW CORNING onto the O ring to prevent the O ring from sticking When reinstalling the service lid the screws must be tightened to 0 8 Nm 7 lbf in to ensure the unit is sealed correctly to maintain the hazardous location certifications and the IP66 enclosure rating Refer also to Figure 24 Desiccator 2 5 SATA SSD or HOU O ring Service Lid ae counter sunk screw M3x4 4x Figure 25 Service Lid assembly 5 6 3 Changing the Desiccator Typically the desiccator does not need to be changed when the Service Lid and Gland Plate are mounted with all holes in the Gland Plate closed But if your application requires frequent opening of the Service Lid or other actions which lead to an increased exchange of humidity it could be necessary to exchange the desiccator The indicator on top of the cartridge will turn pink when an exchange Is required The desiccator is threaded and must be screwed into the metal plate assembled with the Service Lid The desiccator has a right hand thread and can be easily exchanged The desiccator is secured by a rubber washer During installation make sure the desiccator is turned 1 4 turn after the rubber washer contacts the metal plate To access the desiccant remove the Service Lid as described in section 5 6 1 Removing the Service Lid 38 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 5 Field Maintenance To activate the desiccant
12. 89 Mousednd EES 26 39 iReMmoOte Power Buton PWR BIN eec 27 O AUAM T e eea Acces ieee ca iceman Niuean amen Scsiatoee 27 Chapter4 Embedded Controller 29 4k TaK or me Gun ee Ree tg e E 29 GER tere GILLI CONTO E 29 SEM of e pcx renee E AOT TTTS PT E 29 44 Advanced Configuration and Power Interface LACH 29 AG Powerand Heater BR 30 Chapters Field Maintendh E 31 D IM PECHO E 31 Ee Seeerei ler ele 32 SD le E 33 S4 Gana Plate RemMovalgnd e ten EE 33 Side REMON US CON PIS nd in 33 542 Ro ting Caples through the Glana Plate EN 34 S43 PSNI Ne cani PIQUE A AAAA 34 FA BONON O E 34 Seen Ee ES T 34 5 5 Replacement of the Gland Plate Retention SCrews ss sssssssssssseiirrssssssssserrrrrerrressssssssnn 34 SE EE aa A ncnes asevaiienssssens nists 37 Sond tee Nile Sei E 37 Soe ASTON GES Service La irc steerer tune 38 S63 EE TAS Ee EE 38 S04 Chandna The SSD Or ee 39 6 06 51 IMSTGIING GN ExpressCard DEVIS ae 39 I CROONING S BORD E 40 Dr PRO GIN sa TEE gare seem 41 SEL REMOVING LIN FEON EE 41 e tee ER ORPI un 41 Br Repco NG POMS sissies cece ccc eee eee arena ean mean 43 Appendix A Wolverine III Agency Approvals and Regulations 45 MP EPnT tT orEreT EET rPT TTI rrPTT HTT PEPE E PPP ESINE ne nr EE 45 AZ GO enee E 46 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 1 Introduction The Wolverine III industrial computers are rugged panel computers runni
13. Caution When operating the Wolverine III in a hazardous environment all cabling must access the I O Panel through the Gland Plate with the exception of the WLAN antennas Warning When operating the Wolverine III in a hazardous environment WLAN antennas extension cables with WLAN antennas or dust caps must be mounted on all WLAN outputs Only isolated antennas are allowed where the inner part is not touchable after mounting For antenna locations refer to Figure 15 October 2014 5 Chapter 2 Getting Started Wolverine III Agency Approvals and Regulations 2 3 5 Wolverine III Dimensions DR 16 063 ae 115 905 ATEN J d OAI i FRONT VIEW Figure 2 Wolverine III Dimensions Front View 373 114 685 TOP VIEW Figure 3 Wolverine III Dimensions Top View 6 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D GFK 2789D Chapter 2 Getting Started 104 409l 12 9957 lei wh Een Aare De Lf 606 1 850 M xl 81035 18 mm 035 inch working thread REAR VIEW Figure 4 Wolverine II Dimensions Rear View 13 8 10 54 3 ME l each sidel E ao E Ze 6 0315 Cc a mr i o mm 0 375 inch fh working Thread 316 I Ici ww A di Ki a ihs SETVICe opening LEFT SIDE VIEW Figure 5 Wolverine III Dimensions Left Side View October 2014 7 Chapter 2 Getting Started Wolverine I
14. ESA Mount 16 Nonincendive USB wiring for Class 1 Division 2 Groups ABCD 28 Options Wolverine Ill 2 Ordering Information Wolverine Ill 3 O rings 37 Part numbers 5 Power AC 23 DC 24 Power and Heater LEDs 34 Printer port LPT1 26 PS 2 Mouse and keyboard ports 31 Remote PWR BIN connector 32 Replacing the Fans 47 RS 422 and RS 485 26 Safety 7 Serial communication ports 26 Service lid 41 Solid state drive SSD 43 Specifications Wolverine III environmental 3 functional 2 mechanical 3 Standard Part Numbers Wolverine Ill 3 Technical Support ili Thermal zones 33 Torque values cable glands 21 38 screws 10 Unpacking 7 USB ports 27 VGA port 31 Visor 19 Warnings General 8 hazardous areas 9 Weight 3 WLAN port 30 Wolverine III Ordering Information 3 WV3ACCPANLMT Panel Mounting Kit 15 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D GE Intelligent Platforms Additional Resources Information Centers For more information please visit the GE Headquarters Intelligent Platforms web site 1 800 433 2682 or 1 434 978 5100 WWW d e p co m Global regional phone numbers are available on our web site www ge ip com Copyright 2013 2014 General Electric Company All Rights Reserved Trademark of General Electric Company and or its subsidiaries All other brands or names are property of their respective holders GFK 2789D
15. GFK 2789D GE Intelligent Platforms Industrial Computer Products Wolverine Industrial Display Computer Hardware Reference Manual GFK 2789D October 2014 October 2014 1 Warnings Cautions and Notes as Used in this Publication Warning Warning notices are used in this publication to emphasize that hazardous voltages currents temperatures or other conditions that could cause personal injury exist in this equipment or may be associated with its use In situations where inattention could cause either personal injury or damage to equipment a Warning notice is used Caution Caution notices are used where equipment might be damaged if care is not taken Note Notes merely call attention to information that is especially Significant to understanding and operating the equipment These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met during installation operation and maintenance The information is supplied for informational purposes only and GE makes no warranty as to the accuracy of the information included herein Changes modifications and or improvements to equipment and specifications are made periodically and these changes may or may not be reflected herein It is understood that GE may make changes modifications or Improvements to the equipment referenced herein or to the document itself at any time This document is int
16. General Torque Values for Screws Use a PH1 screwdriver for the cross head Phillips screws Unless otherwise specified use the following torque values when tightening screws Table 10 Recommended Screw Torque Values Screw size Torque in lbf in e Il D 4 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 2 Getting Started 2 3 4 Mounting Location GFK 2789D This unit is designed to operate in an outdoor environment The mounting method must be able to support the weight of the unit under shock and vibration conditions for the given application To insure proper operation take care not to install unit in tight confined areas During mid day operations when the effect of solar heating is at its peak Surrounding walls and surfaces can reflect additional solar energy and cause the unit to overheat If this happens shut down until temperatures fall back to normal operating conditions The unit must have a minimum clearance of 154 mm 6 per side behind below and above for cooling This does not include mounting parts and wiring to and from the unit This clearance needs to be increased if surrounding surfaces radiate heat When operating the Wolverine III in a hazardous environment all cabling with the exception of the WLAN antennas must access the 1 0 Plate through the Gland Plate For additional requirements for Gland Plate removal and installation see section 3 1 Gland Plate
17. II Agency Approvals and Regulations 2 3 6 Mounting Options Depending on your system configuration and mounting requirements several different methods of mounting can be used The three basic methods are listed below Panel Mounting The Wolverine III can be mounted in a panel opening using the Panel Mount Kit WV3ACCPANLMT For details see section 2 3 7 Panel Mounting Wall or Desktop Mounting VESA Mount Mounting points in accordance with the VESA Mounting Interface Standard are located on the rear of the unit See Figure 2 Rear view Use M6 screws to mount the Wolverine Ill Free thread length is 8 mm For details see section 2 3 8 Wall and Desktop Mounting VESA Mount Floor Mounting A floor stand is available for the Wolverine Ill The stand provides adjustments for the height rotation and tilt of the screen For details see section 2 3 9 Floor Mounting 2 3 7 Panel Mounting The Wolverine III can be panel mounted using the optional WV3ACCPANLMT Panel Mounting Kit Begin by locating a cutout 332 mm high x 387 mm wide 13 1 x 15 2 with a maximum corner radius of 18 mm 0 7 in the target panel using the following figure as a guide Panel thickness must be at least 2 mm but no more than 10 mm 0 08 to 0 40 404 mm 15 9 in Panel Cutout Outline of Wolverine III Faceplate 387 mm 15 2 in 349 mm 13 7 in 332 mm 13 1 in 8 mm 0 3 in La Je gt La EE E E S ES EL ERP
18. OIS CROIS 4 Bo ANNE Ne E e 5 RS e ebe E S Le OCTO 71 6 E ee GE 6 Chapter EIERE 1 21 Unpacking ol ate e ere EEN 1 ZS eam Rn PERE ETE Cee ees Oe EEE 1 PA E tele e Ee I S a e E suas nasa seaaoa vacasseeaasceeuaceeaaioes 2 20 Ee e Ee RE O trrsn rer tts eersna eye TnO 2 252 WOLMINGS TOF Hazardous AledS EE 3 25 57 General Torgus Valis ele 4 E MON IR H Be eet GE 5 RoD OWEN II AIIM TOT IOUS aarre asa acc cceceectaeens 6 2 30 MONT BE ege 8 GG POS OA 8 2 3 8 Wall and Desktop MountindiVESAMOUnth na enr 10 POD MOOM OUNT E 11 2 3 10 Keyboard Tray Visor GAS anaes 13 Chapters Connectors and CODING uiensssssiennsesnn 15 E RC 0 10 RT et 15 Se ReEMVINMECAnd e 16 3 1 2 Routing Cables through the Gland Plate eicecscccasescocsccccsesccosszezszeccesveceszecesseuesbasaenees 16 Sio ORO UE Ges HO Cabe e ue 16 SLA Re Gelee Kuele ie Re 17 OR OR seeceseceassecasecczeccectcecezeccer 17 A OO OR erp A PP nT or HnP OTOH A 17 Dee EE 17 Be CNS sarees sree reesei EA 19 So lee ein KR EE 21 34 tee 21 342 RS4220na RS 485 Operating le 21 OO 22 D MM USB POS RC EE 22 3 4 5 Intrinsically Safe Ex ic USB Port Nonincendive USB Wiring for COS IIB VATS EE 23 October 2014 V Contents vi 293 AMEME CAN e 24 3 5 2 Ethernet Indicators ssssesssssssssssssrssssssssssrrsssssssssssrressssnsserresssnnsntrrsnsnnnnttrnrnnnnnttrrnrenssnnntnrressssnns 24 Io WAN ee geleet e UE 25 Se POR O U een ORR nnn On torrente a eee 25 Si VOA POF EE 26 3
19. Wrap Push the cable tie wrap down through the first hole and up through the second Use the pliers to close the cable tie wrap Cut the long unused end of cable tie wrap off Refer to Figure 27 for correct position of the cable tie wrap 40 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 5 Field Maintenance 5 8 Front Plate The two Front Plate assemblies WV3SPFPLATEO and WV3SPFPLATE1 both include one assembled front plate one set of mounting screws plus two spare screws an O ring for the front plate and a tube of DC4 silicon grease The exchangeable Front Plate consists of a metal frame a touch screen and an overlaid key pad The Front Plate must be exchanged as one piece to ensure the unit is sealed correctly and to maintain the hazardous location certifications and the IP66 enclosure rating 5 8 1 Removing the Front Plate To open the Front Plate remove the 34 M3x6 counter sunk screws as shown in Figure 29 Carefully lift up the Front Plate a small amount Caution Before the front plate can be removed two flat cables have to be disconnected The cable to the overlay key pad has a self locking connector Disconnect this one first by pushing onto the sides and pulling it off Then loosen the screws of the touch cable holder and pull the connector off the touch cable 5 8 2 Installing the Front Plate GFK 2789D When reinstalling the Front Plate ensure that the O ring is in its groov
20. about the Wolverine III can be found in the following documents available on the GE Intelligent Platforms support website www ge ip com support GFK 2790 Wolverine II Extended Service Manual GFK 2791 Wolverine II Quick Start Guide GFK 2797 Wolverine IIl Rugged Panel PCs Extended Service Kits GFK 2894 Wolverine IIl Rugged Panel PCs USB Recovery Procedure GFK 2910 Wolverine III Keyboard WVKBUSBOO1A Datasheet GFK 2943 Wolverine III Software Development Kit Reference Manual GFK 2789D October 2014 5 Chapter 1 Introduction Wolverine III Agency Approvals and Regulations 1 8 Additional Support For support and information visit GE Intelligent Platforms website at http www ge ip com The files for this manual and other related documentation are available there Additional region and language specific websites and telephone numbers are found on the Contacts page at the front of this manual Information for components and driver software can be found at the following locations Intel Corp www intel com Microsoft Corp www microsoft com MetaPlume Corp www viaarena com 6 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 2 Getting Started This chapter covers the initial preparation of your Wolverine III for use unpacking inspection and installation of the hardware Following these procedures will ensure proper operation after shipping and ease the integration with your application 2 1 Unp
21. acking and Inspection 2 2 Safety GFK 2789D Please check that the delivered package contains the following items Table 9 Wolverine III Package Contents Qty Item 1 Wolverine III industrial computer 1 Antenna kit supplied only with the Wireless option Warnings Please read these safety instructions carefully Place this equipment on a stable surface during installation Dropping it or letting it fall could cause damage Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be complied with Never pour any liquid into an opening This could cause fire or electrical shock Only qualified service personnel should open the equipment If any of the following situations arises get the equipment checked by qualified service personnel Liquid has penetrated into the equipment The equipment has been dropped and damaged The equipment has obvious signs of breakage October 2014 Chapter 2 Getting Started Wolverine III Agency Approvals and Regulations 2 3 Hardware Installation The Wolverine III has been designed to ensure simple installation of the system 2 3 1 General Warnings Warnings Input and output wiring methods and cable types must be in accordance with ordinary location wiring methods and in accordance with the authority having jurisdiction Do not remove the Service Lid while power is ap
22. anual GFK 2789D Chapter 1 Introduction Table 7 Indicators Cleaning LED LED is on while the unit is in cleaning mode Preheating LED Indicates that the system is heating up to get into Operating mode LED automatically turns off when the unit is in Operating mode Ethernet Link LED Indicates a link on the particular Ethernet line PWR LED The PWR button is illuminated green when the unit is in operation 1 6 Wolverine Ill Accessories The following table lists optional accessories that are available for the Wolverine III industrial computer Table 8 Accessories for Wolverine III en Part Number Description Panel Mounting Kit WV3ACCPANLMT For panel mounting See section 2 3 7 Panel Mounting for details Replacement Gasket for WV3SPPMOUNTO For panel mounting See page 7 panel mounting Keyboard WVKBUSBO01A ATEX USB Intrinsically Safe IS keyboard See GFK 2910 Intrinsically Safe Keyboard Datasheet for details Floor Stand WV3FLRSTD For floor mounting See section 2 3 9 Floor Mounting for details Keyboard Tray WV3KBTRY For use with wall mounted or floor stand mounted units Visor WV3KBVISR For use with wall mounted or floor stand mounted units Handle WV3HDLSET For use with wall mounted or floor stand mounted units Please contact your sales representative for latest information on options and accessories Accessories are subject to change without notice 1 7 Related Documents Additional information
23. ate Retention Screws If one or more of the captive Gland Plate retention screws is damaged or lost the Replacement Gland Plate retention screws found in the WV3SPIOPSCWO kit provides replacement parts To replace use the following procedure 34 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 5 Field Maintenance 1 Remove the Gland Plate as described in section 5 4 1 Removing the Gland Plate 2 Remove any damaged screw by turning counter clockwise while pulling slightly to engage the threads with the retainer ring If the retainer ring is intact and in good condition skip to step 6 below Position the cover as shown in Figure 19 Place a new O ring at the opening of the screw retainer body as shown Figure 19 Initial placement of the retainer ring 5 Usea4mm 5 32 punch to press the O ring fully into the retainer body as shown in Figure 20 The inside shaft of the retainer body is slightly tapered to compress the O Ring and thereby retain the screw ae et Figure 20 Press fit of the retainer ring GFK 2789D October 2014 35 Chapter 5 Field Maintenance Wolverine II Agency Approvals and Regulations 6 Carefully insert a new screw and spring as shown in Figure 21 Applying slight pressure turn the screw clockwise to engage the screw threads with the retainer ring taking care not to press hard enough to dislodge the O ring Yi Figure 21 Insertion of the retention screw
24. ay Computer Hardware Reference Manual GFK 2789D Chapter 3 Connectors and Cabling 3 1 4 Installing the Gland Plate To install the Gland Plate 1 Ensure that the O ring Is in its groove and is not damaged Further ensure that the flange of the Gland Plate and the I O Panel are clean 2 Apply a thin layer of DC4 silicon grease from DOW CORNING on the O ring This prevents the O ring from sticking For replacement O rings see page 33 3 Place the Gland Plate on the unit and tighten the captive screws to 0 8 Nm 7 Ibf in to ensure the unit is sealed correctly to maintain the hazardous location certifications and the IP66 enclosure rating 3 1 5 Bonding Connect the external bonding stud below the Gland Plate to a minimum 4 mm bonding wire It has an M4 thread Use means such as a ring terminal to ensure proper connection Warning The nut with washers should always be installed even if no ground connection is present to ensure resistance to impact of the case For example this situation could occur during transportation of the device 3 2 1 0 Plates IOPs 3 2 1 AC Units af a NX 5 S SNAN KA I e B Lass Uc a PSS BR fs a Ge IR zi Gr a A bei D amp USBI y V583 FUSE B 250 MANUFACTURER i COOPER BUSSHMANN F lt 2 PART NO S501 6 R e a LEA Figure 16 1 0 Plate AC Units GFK 2789D October 2014 17 Chapter 3 Connectors and Cabling Wolverine III Agency Approvals and Regulati
25. battery kit is WV3SPBATTOOO This kit includes one battery and a cable tie wrap In addition to the kit you will also need a small screw driver a small pair of wire cutters and a small gripper tool such as needle nose pliers Warning e The battery used in this device may present a fire or chemical burn hazard if mishandled Do not disassemble heat above 100 C 212 F or incinerate Dispose of used batteries safely in accordance with the battery manufacturer s Material Safety Data Sheet MSDS e Do not leave any loose parts such as batteries or tools in the unit They could cause short circuit When replacing the Battery only use Manufacturer Rayovac Europe B V Part Number BR2032 BA The Battery must be secured by a cable tie wrap To exchange the battery do the following steps Put the unit with the display downward onto a table Find the Battery as shown in Figure 27 Cut the cable tie wrap off with a wire cutter Then take the loose cable tie wrap out of the unit Take a small screwdriver and push the battery out of the battery clamp The red arrow shows where the battery can be pushed out Use the pliers to take the battery out of the unit Battery in battery clamp Cable Tie Wrap Figure 27 Service Lid Opening with Battery Place the new battery in front of the battery clamp with side up Use the gripper to slide the battery in Form the cable tie wrap as shown in Figure 28 Figure 28 Bent Cable Tie
26. e and is not damaged Further ensure that the flange of the front plate and the housing are clean Apply a thin layer of DC4 silicon grease from DOW CORNING on the O ring to prevent the O ring from sticking Connect the touch screen cable first Watch for correct polarity as indicated by the 1 on the PCB and the connector Secure the touch screen cable with the touch cable holder and two screws Connect the flat cable to the overlay key pad To reinstall the Front Plate the screws must be tightened to 0 8 Nm 7 Ibf in to ensure the unit is sealed correctly to maintain the hazardous location certifications and the IP66 enclosure rating October 2014 41 Chapter 5 Field Maintenance Wolverine II Agency Approvals and Regulations pan head screw M25x5 Torx 6 Nm W3 Touch cable holder a a g A amp 8 8 amp H 8 a Loctite 425 counter sunk screw A TufLok VibraStop di degen Figure 29 Front Plate 42 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D 5 9 GFK 2789D Chapter 5 Field Maintenance Replacing the Fans The Fan Assembly kit WV3SPFANKITO includes two assembled Fans left and right with supports and connectors screws to mount fan supports plus a set of screws for mounting the front plate one set of screws two spare To replace the fans remove the Front Plate as described in section 5 8 1 Removing the Front Plate Unplug the two fan connectors and loosen
27. ended for trained personnel familiar with the GE products referenced herein GE may have patents or pending patent applications covering subject matter in this document The furnishing of this document does not provide any license whatsoever to any of these patents GE PROVIDES THE FOLLOWING DOCUMENT AND THE INFORMATION INCLUDED THEREIN AS IS AND WITHOUT WARRANTY OF ANY KIND EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED STATUTORY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE indicates a trademark of General Electric Company and or its subsidiaries All other trademarks are the property of their respective owners Copyright 2013 2014 by General Electric Company All Rights Reserved GFK 2789D October 2014 Waste Disposal The mark or symbol on any electrical or electronic product shows that this product may not be disposed of in a trash bin Such goods have to be returned to the original vendor or to a properly authorized collection point Electronic waste disposal symbol with black bar as explained below The black bar underneath the waste bin symbol shows that the product was placed on the market after 13 August 2005 Alternatively the date of placement on the market is shown in place of the bar symbol CE Conformance Declaration CE certification can only be granted to complete and operational systems The Wolverine III system is certified as required The CE mark and year of production is s
28. environment WLAN antennas extension cables with WLAN antennas or dust caps must be mounted on all the WLAN outputs Antennas certified for the hazardous area of the intended installation must be used For antenna locations refer to Figure 15 on page 16 3 6 Horn Output GFK 2789D The Horn output is available on the back 1 0 Plate through a terminal block The horn output voltage is derived from the input voltage of the system Due to a voltage loss at the solid state relay the AC voltage is lowered by 1 V and the DC voltage is lowered by 0 5 V compared to the input voltage The maximum allowed current is 1 A The current drawn on the Horn Output has to be limited by the user with a fuse of 1 25 A The terminal block is rated for wire size AWG 12 22 4 mm 0 5 mm and has a torque rating of 7 in lbs 79 Ncm max For DC powered Wolverines the terminal denoted by the H sign is V dc switched through an internal relay the terminal is DC return In addition it is required that for DC powered Wolverines inductive loads must be diode suppressed For AC powered Wolverines the terminal denoted by the Hl sign is AC Line voltage switched through an internal relay the N terminal is AC return Maximum cable length is limited to 3 meters 10 ft or less It is recommended to use at least AWG 18 1 mm wire for the terminal block If using a flexible conductor the use of a cable end sleeve ferrule or similar means of suppo
29. he Gland Plate must be fixed to the main chassis to maintain the enclosure protection rating Caution Modification of any part of the housing invalidates the enclosure protection Table 5 Mechanical Specifications The main chassis is manufactured from aluminum and Main chassis construction houses all electronics 10 2 kg 22 5 lbs with Gland Plate October 2014 3 Chapter 1 Introduction Wolverine III Agency Approvals and Regulations 15 Controls and Indicators m Function Keys 1 Es P BOOTS gt _ Cleaning LED SE Preheating LED a a em OF 1 PWR Power Ethernet Link LEDs Right Mouse LEDs Brightness Adjust Figure 1 Overlay Including Control Buttons and Function Keys Option O3 Table 6 Control Buttons and Function Keys Button Description Hold this button for at least 4 seconds to perform a hard switch OFF Brightness adjust Use the up arrow to increase the backlight brightness down arrow to decrease Cleaning Hold button for 3 seconds to enable Cleaning mode This mode disables all buttons and the touchscreen so that the unit can be cleaned To disable Cleaning mode hold this button for another 3 seconds LED off Disables all status LEDs except the Cleaning LED on the overlay Note The Cleaning LED still illuminates when Cleaning mode is active Function Keys Function Keys F1 to F12 4 Wolverine III Industrial Display Computer Hardware Reference M
30. hown on the type label li Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Contact Information Contact Information If you purchased this product through an Authorized Channel Partner please contact the seller directly General Contact Information Solution Provider solutionprovider ip ge com Technical Support If you have technical problems that cannot be resolved with the information in this guide please contact us by telephone or email or on the web at www ge ip com support Americas Europe the Middle East and Africa Phone 800 1 433 2682 0 1 433 2682 EMEA Direct i a a a 420 23 901 5850 GE toll free 800 option is unavailable or i Altice from a mobile telephone Primary languages of support English French German Italian Czech Spanish Asia Pacific Phone 86 400 820 8208 86 21 3877 7006 India Indonesia and Pakistan Technical Support Email support cn ip ge com China support jp ip ge com Japan support in ip ge com remaining Asia customers Customer Care Email customercare apo ip ge com customercare cn ip ge com China GFK 2789D October 2014 iil Contents GFK 2789D Warnings Cautions and Notes as Used in this Publication i CORACAO SR a estan deuareuetereeman ease eae jii REH V Chapter MMtrodUCHON BE 1 TE SO 1 Pe a e OE OEN 1 Dee ele later ege d 132 Wolverine UH NTONNO EE S LA Environmentalana Mechanical Spec CANON circ es 3 ES COMU
31. ircuit breaker There is one user serviceable fuse on the back 1 0 plate See Chapter 5 Field Maintenance for replacement fuse details Note When unit is shut down it still needs power The amount of power that is required depends on the ambient temperature Leaving the unit connected to power provides instant on capability down to 40 C Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 3 Connectors and Cabling 3 2 2 DC Units D 4 eus G VK GG ey f H OK FUSE 204 125VDC MANUFACTURER 5 LITTELFUSE Qe PART NO 314020P GC D E Figure 17 I O Plate DC Units DC Power Warning Serious injury due to shock is possible if unit is wired incorrectly or connected to voltage exceeding the input voltage range To power your Wolverine III DC unit connect the following lines to the DC Power terminal block and chassis Positive line E Earth ground DC Net Negative line D PE Protective Earth GFK 2789D October 2014 19 Chapter 3 Connectors and Cabling Wolverine III Agency Approvals and Regulations Table 13 Power Requirements Wolverine III DC DC Input 24V dc Voltage Range 11 32 V dc Power Rating 190 W 19 0 A max Caution Make sure that the polarization of the power lines is correct and complete including both earth ground and Protective Earth PE ground Incorrect polarization will result in serious da
32. ity insert two M6 x 12mm cap screws through the right hand 75 mm VESA mounting holes in the floor stand mounting plate and display attachment plate into the tapped holes in the back of the display Tighten to no more than 3 7 Nm 33 Ibf in 12 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 2 Getting Started 2 3 10 Keyboard Tray Visor and Handle Three Wolverine III options are particularly useful with VESA and Floor Stand mounting the keyboard tray WV3KBTRY the visor WV3KBVISR and the handle WV3HDLSET None of these items are useable when the Wolverine III is panel mounted The visor is helpful in outdoor installations or anywhere that overhead lighting might cause glare in the display screen The keyboard tray and visor are shown in Figure 9 Wolverine Floor Stand Option above and in the figure below Both mount to the side of the display in a similar fashion with a pair of flat M4 x 8 mm screws through brackets on either side into tapped holes in the side of the Wolverine III Visor position 2 lock 2 places N da Visor attachment bolts M4 four places Keyboard tray ott attachment bolts gt Sr M4 four places Keyboard tray LF lock 2 places Figure 13 Wolverine III Keyboard Tray and Visor Attachment The optional handle mounts to the top of the Wolverine III as shown in the following figure
33. lligent Platforms October 2014 1 Chapter 1 Introduction Wolverine III Agency Approvals and Regulations 1 3 Wolverine III Features and Options This manual describes the basic product plus options Your product may not have all options implemented Please check your purchase contract to verify which options are implemented Table 1 Common Features Ports Four USB 2 0 ports Two Ethernet ports 10 100 1000 Mbit s Two RS 232 RS 422 RS 485 ports configurable via BIOS Two RS 232 ports One parallel port Two PS2 ports One audio port Mic Line Out One VGA port One horn output terminal block Expansion Slot ExpressCard supports 34 mm and 54 mm modules System Management Accelerometer Thermal Monitoring and Management Elapsed time indicator All available through Operating System Power Supply ETL Listed Dedicated controls Right mouse button dimming cleaning function disable indicator LEDs and function keys Availability depends on Overlay option Table 2 Options Processor Speed and RAM 2 26 GHz 4 GB RAM 2 26 GHz 2 GB RAM or 1 2 GHz 2 GB RAM Mass Storage 32 40 or 64 GB 2 5 SATA Solid State Drive SSD or 100 GB Hard Disk Drive HDD Front Panel Overlay No buttons Control buttons only or Control buttons and function keys Power feed 11 32 V dc or 100 240 V ac 47 63 Hz Wireless Local Area Network None or WLAN 802 11 b g n Operating System None Windows XP Professional or Windows 7 Professio
34. lverine III Floor Stand Option October 2014 11 Chapter 2 Getting Started Wolverine III Agency Approvals and Regulations Attaching the Wolverine III to the Floor Stand After the floor stand has been secured mount the Wolverine III to the floor stand 1 First loosen the locking nut and locking bolt as shown in the figure below to allow the display attachment plate to be lifted upwards off of its hinge at the top of the floor stand mounting plate Hinge N Display attachment Floor stand CH screws M6 four places mounting plate Display attachment plate Display locking CA screws two places Locking pin Locking nut Locking pin handle Figure 11 Wolverine III Floor Stand Attachment from Right hand Side 2 The display attachment plate should be fitted to the back of the Wolverine III using four M6 x 8mm flat head screws into the 100 mm VESA mount screw holes See section 2 3 8 Wall and Desktop Mounting VESA Mount Torque to no more than 3 7 Nm 33 Ibf in OO Attach plate to display Display back with M6 x 8mm flat attachment plate head screws 4 places Figure 12 Wolverine III Display Attachment Plate 3 Next hang the display on the floor stand mounting plate using the hook at the top of the attachment plate Lower it into position lock it with the locking pin then re tighten the locking bolt followed by the locking nut 4 Finally for added secur
35. mage to the Wolverine III The power supply input to the Wolverine III uses a terminal block that shall be connected to no greater than a 50 A branch circuit for DC units Connect the PE wire to the D stud Connect earth ground of the DC power supply to the E terminal of the terminal block If such earth ground does not exist in the DC power supply connect the E terminal to the D stud Ensure that the DC power supply has a connection between the negative supply and PE D If this connection cannot be ensured somewhere in the DC power supply connect it directly on the I O plate of the Wolverine III The terminal block is rated for wire size AWG 22 12 0 5 4 mm and has a torque rating of 7 in lbs 79 Ncm max It is recommended to use at least AWG 18 1 mm wire for the power input If flexible conductor is used it is mandatory to use a cable end sleeve ferrule or similar means Do not connect more than two wires to each screw terminal of the terminal block To remove power from the unit the proper method is to switch off power at the external circuit breaker supply power to the unit Note There is one user serviceable fuse on the back 1 0 plate See Replacing Fuses on page 34 for replacement fuse details Note When unit is shut down it still needs power The amount of power that is required depends on the ambient temperature Leaving the unit connected to power provides instant on capability down to 4
36. n order to provide higher EMC immunity and maintain CE Mark compliance the serial cables must be shielded 3 4 4 USB Ports The four USB ports are 2 0 compliant and are located on the back O Plate VCC USB USB GND socket outside view In order to provide higher EMC immunity and maintain CE Mark compliance the USB cables must be shielded 22 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 3 Connectors and Cabling 3 4 5 Intrinsically Safe Ex ic USB Port Nonincendive USB Wiring for Class 1 Division 2 Groups ABCD Control Drawing YMXIC WV3 Intrinsically safe USB port Ex ic IIC 14 Associated Field Apparatus in accordance with equations for evaluation using EN 60079 0 2009 Wolverine III Field wiring EN 60079 11 2007 parameters Ui gt Uo Nonincendive Cl 1 Div 2 Groups ABCD li gt lo in accordance with Li Le lt Lo ANSI ISA 12 12 01 Ci Cc lt Co If the electrical parameters of the Entity Parameter cable are unknown the following values Uo 6 51 V may be used lo 0 73 Le 0 20uH 0 305m 1 ft Po 101 W Ce 60pF 0 305m 1 ft Lo 70 uH Nonincendive Field Wiring must be Co 200 pF installed in accordance with Article 501 of the National Electrical Code Functional Parameter ANSI NFPA 70 or authority having Port is USB 2 0 compliant Jurisdiction d ipa i passive devices Nomenclature 0 1 1 10 and 1 000 1000 The circuit is galva
37. nal Caution A An operating system version designed specifically for use with SSDs is required to minimize write cycles enhancing the lifespan of the SSD System Recovery USB Flash A USB flash drive capable of restoring your system disk to its as Drive shipped condition is available on request 2 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 1 Introduction 1 3 2 Wolverine Ill Ordering Information The following table lists the part numbers used to order the standard Wolverine II configurations Table 3 Wolverine III Standard Part Numbers Power Wireless Operating Part Number Required Ethernet System Gland Plate WV3402114010 WV3402114020 No No WV3402414020 no Windows xP pro Bonome we windows 7pro Bonome All standard units include the 2 26 GHz Processor with 4 GB RAM plus a front panel overlay with control and function buttons For configurations or options not listed please contact GE Intelligent Platforms LA Environmental and Mechanical Specifications GFK 2789D Table 4 Environmental Conditions Temperature Humidity 5 to 95 RH Enclosure Protection NEMA4x IP66 Vibration Operating 2 g 10 Hz 500 Hz only with SSD Shock Operating 40 g saw tooth 11ms pulse 3 Axis only with SSD Less than 1000 m 3300 ft Altitude Operating Note For thermal derating at altitudes above 1000 m contact GE Intelligent Platforms t Note T
38. nditions and their meaning Table 23 PWR and HTR LEDs PWR HTR LED LED a o soy Operating Status Flashing Slow k KS WE FS Flashing Fast dee ZAR Flashing Slow a ETN Flashing Fast SE Vi AN Wolverine III Industrial Display Computer Hardware Reference Manual WV III is Operating Power On is requested As soon as all required circumstances are reached the WV III will start This can be set and reset by power button press Waiting for proper temperatures Temperatures are out of specification and WV III thermal management tries to generate valid ones One or more temperatures are out of specification Please save and close all applications and shut the system down to prevent damage Please check ambient temperature One or more thermal sensors are not readable Proper system thermal management cannot be guaranteed Save and close all applications and shut system down to prevent damage Disconnect the WV III from power for several minutes and then reconnect If this does not solve the issue contact Support One or more temperatures became out of specification after operating conditions were already reached System is prevented from starting until this error is confirmed from the user by pressing the PWR button one time Check ambient Temperature One or more Thermal Sensors are not readable Proper system thermal management cannot be guaranteed System is prevented from s
39. ng Windows operating systems They are designed to be suitable for use in hazardous and harsh environments Each member of the Wolverine III industrial computer family is a fully self contained personal computer PC compatible computer with a built in flat screen display and resistive touch screen The unit is housed in a rugged metal case to protect the system against dust water and mechanical damage Wolverine III industrial computers are available as either 24 V dc units that accept a range of 11 32 V de or as 115 230 V ac units that accept a range of 100 240 V ac Wolverine III AC and Wolverine III DC computers provide an enhanced feature set including heaters for extended temperature operation and a front keypad overlay The unit is supplied completely assembled and requires only mounting and connecting 1 1 Certification Wolverine III is certified for Zone 2 environments according to ATEX 94 9 EG and Class 1 Division 2 per ANSI ISA 12 12 01 1 2 Altitude GFK 2789D Altitude air pressure and ambient temperature influence the thermal operation of the components described in this manual They have been developed and tested at approximately 1000 m 3300 ft above sea level at ambient temperatures of 40 C to 60 C Because of only marginal variations within a limited range of altitudes these products operate as specified within altitudes from sea level to 1000 m For thermal derating at altitudes above 1000 m contact GE Inte
40. nically ct he rae py d connected with the chassis pdt Drawing YMXIC W3 C E Caution To avoid moisture dust or liquids in the connector keep the dust cap closed when port is unused GFK 2789D October 2014 23 Chapter 3 Connectors and Cabling Wolverine III Agency Approvals and Regulations Caution Ex ic connections must be verified against EN 60079 25 For permanently installed USB devices the following mating plug is recommended Manufacturer Amphenol Part Number USBFTV6N 3 5 Ethernet LAN Ports Two RJ 45 Ethernet connectors are available on the back 1 0 plate for connecting standard unshielded or shielded twisted pair cable Both ports support Boot over LAN Wake on LAN Is supported with magic packet INANANAN E a LED 1 l CH socket outside view Table 17 LAN Port Pin Assignments Pin men 10006886 e Ise a fa nc eo 5 5 2 Ethernet Indicators Note Activity is not shown LED1 Function Link The link is physically connected ff 24 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 3 Connectors and Cabling 3 5 3 WLAN Port Optional The Wolverine III offers an 802 11a b g n i wireless network adapter with two external antenna connectors beside the 1 0 Plate For better signal quality an extension cable can be used to locate the antennas away from the system housing Warning When operating the Wolverine III in a hazardous
41. ns and suitable for the environmental conditions in which the unit is used NEC section 500 applies in the US and EN 60079 14 applies in Europe For the lower operating temperature the lowest ambient temperature down to 40 C and for the upper temperature the highest ambient temperature up to 60 C plus 30 K 90 C is required Tlow ambient lt Twiring lt Thigh ambient 30 K All cables brought through the cable glands need a support to avoid forces or movement of the cables in the glands If glands are connectorized the cables need to be supported to avoid high forces on the Gland Plate The support for the cables should be mounted to the Wolverine III or to the mount when Wolverine III is fixed to the mount 3 1 Gland Plate GFK 2789D The unit is available with different pass through glands for cable connections required to maintain enclosure protection rating These glands are water and gas tight and must be tightened with a torque described in the gland manufacturer s instructions provided with the unit Cables must be passed through the glands and wired to the associated I O connectors Four glands and one USB connector are available on the Gland Plate shown in Figure 15 Note Figure 15 indicates all available I O for the Gland Plate but does not cover all available configurations Contact your GE Intelligent Platforms sales representative for a quote for a customized Gland Plate October 2014 15 Chapter 3 Connec
42. ons 18 AC Power Warning Serious injury due to shock is possible if unit is wired incorrectly or connected to voltage exceeding the input voltage range To power your Wolverine III AC unit connect the following lines to the AC Power terminal block L Line D PE Protective Earth Ground N Neutral Caution Make sure that the polarization of the Power lines is correct and complete including the Protective Earth PE ground Improper connection will result in serious damage of the Wolverine III Table 11 Power Requirements Wolverine III AC AC Input 115 230 V ac 50 60 Hz Voltage Range 100 240 V ac 47 63 Hz Power Rating 200 W 2 2 A max Table 12 Surge Protection Wolverine III AC EN61131 2 EN 61000 6 2 Line to ground 2KV peak EN 61000 4 5 Line to ground 1KV peak The power supply input to the industrial computer uses a terminal block that shall be connected to no greater than a 20 A branch circuit for AC units Connect PE to D on the terminal block The terminal block is rated for wire size AWG 22 12 0 5 4 mm and has a torque rating of 7 in lbs 79 Ncm max It is recommended to use at least AWG 18 1 mm wire for the power input If you are using a flexible conductor it is mandatory to use a cable end sleeve ferrule or similar means Do not connect more than two wires to each screw terminal of the terminal block To remove power from the unit the proper method is to switch off power at the c
43. ous environment such as a lab A Table 24 Field Replaceable Parts The Wolverine III industrial computer is designed to be serviced in the field The following components can be replaced in the field Replacement Part Number Accessed Through O Rings WV3SPORINGSO Front Plate Gland Plate Service Lid retention screws Front Plate O1 no control buttons WV3SPFPLATE1 NA or function keys Front Plate O3 with control WV3SPFPLATEO NA buttons and function keys Fan assembly two per package WV3SPFANKITO Front Plate Panel Mount brackets WV3SPPMOUNTO Service only in accordance with the applicable chapters in this document Caution When performing this procedure care must be taken that no liquids or dust particles penetrate into the unit K Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D 5 3 O Rings A field replacement kit is available for the O rings and gaskets that are used to seal the various access plates on the Wolverine III industrial computer Table 25 Contents of O ring Replacement Kit WV3SPORINGSO O ring Description Service Lid O Ring Gland Plate O Ring Chapter 5 Field Maintenance Front Plate O Ring Rear Plate O ring DC4 silicon grease from DOW CORNING 5 4 Gland Plate Removal and Replacement The Gland Plate also known as the I O Plate Cover can be exchanged in the field Also to exchange a fuse the Gland Plate must be removed and re installed
44. plied to the system Dangerous power levels may be present in the industrial computer or on power input terminals while power is connected even if the Power On Off indicator is not illuminated The proper method for removing power from the unit is to switch off power at the circuit breaker which is not part of the Wolverine III DC version Power supply is to be connected to an isolated secondary voltage which is separated from the primary circuit by reinforced or double insulation The power supply shall be properly bonded to the main grounding terminal in the end product Ensure a connection between protective earth and negative somewhere in the DC Power Net Power is to be connected to a supply no greater than 50 A maximum AC version Product shall be connected to no greater than a 20 A branch circuit The battery used in this device may present a fire or chemical burn hazard if mistreated Do not disassemble heat above 100 C 212 F or incinerate Dispose of used batteries safely in accordance with the battery manufacturer s Material Safety Data Sheet MSDS Caution The touch screen control buttons and function keys are intended for use with hands or gloved hands Do not use tools such as screwdrivers that have metal parts which may damage the touch screen and controls 2 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D 2 3 2 Warnings for Hazardous Areas GFK 2789D
45. remove the cap as shown in Figure 26 Pull off this cap to activate the Uessiccator Figure 26 Desiccator Activation 5 6 4 Changing the SSD or HDD SATA SSD 2 5 32 GB WV3SPSSD32G0 SATA SSD 2 5 40 GB WV3SPSSD40G0O SATA SSD 2 5 64 GB WV3SPSSD64G0 SATA HDD 2 5 100 GB WV3SPHDD100G0 obsolete To access the SSD or HDD remove the Service Lid as described on page 34 To exchange an SSD or HDD device remove the four M3 counter sunk screws and lift up the device as shown in Figure 25 The installation of an SSD or HDD device is in the opposite sequence Caution Make sure that the SSD or HDD device has the correct orientation as shown in Figure 10 on page 49 5 6 5 Installing an ExpressCard Device The Wolverine Il supports 34 mm and 54 mm ExpressCard modules It is not possible to bring out any cables from an ExpressCard device The Wolverine IIl supports only standard form factors with a length of 75 mm and thickness of 5mm To access the ExpressCard slot remove the Service Lid as described on page 34 Warning Due to safety certifications and environmental conditions only ExpressCard devices that are approved for use with the Wolverine III should be installed GE Intelligent Platforms should be contacted for a list of approved ExpressCard devices GFK 2789D October 2014 Chapter 5 Field Maintenance Wolverine II Agency Approvals and Regulations 5 7 Changing the Battery The part number of the replaceable
46. rt B Tested by an independent third party Explosive Atmospheres Directive Self Declaration in accordance with ATEX European Safety for Hazardous Directive 94 9 EC Independent 3rd party Locations assessment Equipment Group II Category 3 Gas Group IIC Note A product s approval should be verified by the marking on the unit GFK 2789D October 2014 45 Appendix A Wolverine III Agency Approvals and Regulations A 2 Government Regulations U S and European regulations are intended to prevent equipment from interfering with approved transmissions or with the operation of other equipment through the AC power Source The Wolverine industrial computer has been tested by a third party and found to meet or exceed the requirements of U S FCC 47 Part 15 Code of Federal Regulations Title 47 Telecommunication Part 15 Radio Frequency devices Subpart B 2010 10 European EN55022 regulations for Class A digital devices when installed in accordance with the guidelines noted in the appropriate product section These various regulations share commonality in content and test levels with that of CISPR 22 and based on this commonality testing to the each individual standard was deemed inappropriate The FCC requires the following to be published according to FCC guidelines This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to
47. rting the cable is required Do not connect more than two wires to each screw terminal of the terminal block October 2014 25 Chapter 3 Connectors and Cabling Wolverine III Agency Approvals and Regulations 3 7 VGA Port The VGA connector is located on the back 1 0 plate The standard 15 pin D sub connector pin out is shown below oaea o ES e oen 0 ous C fou In nomea lu e oco Ts eom 13 une e Voom a ne Le eons O 3 8 Mouse and Keyboard Ports PS 2 ports for Mouse amp Keyboard are available on the back 1 0 plate and labeled accordingly Table 19 Keyboard Port purple Pin Assignments Pin soa 26 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 3 Connectors and Cabling 3 9 Remote Power Button PWR BTN For use of the remote Power Button use the following connector 12345 OO 0 0 0 oo0o0o 0 1 0 9 Table 21 PWR BTN Pin Assignments Pn Assigmmem e Reserved donua e Reserved idortua o Lesser 3 10 Audio Mic Line Out Mating Plug has to comply with JIS C 6560 JC35P3 3 5 mm 3 pin stereo Maximum level to be applied to the ports is 1Vrms Sleeve Ring Tip Table 22 Audio Mic Line Out Signals Line In blue Out green Microphone red om Signet Signal Signal Tip Left Tip Left Ring Right Ring Right Ring Right Sleeve GND Sleeve GND GFK 2789D October 2014 27 Chapter 4 Embedded Controller 4 1 4 2 4
48. tarting Disconnect the WV III from power for several minutes and then reconnect If this does not solve the issue contact Support GFK 2789D Chapter 5 Field Maintenance 5 1 Inspection GFK 2789D The Wolverine III industrial computer is housed in a sealed gastight enclosure with an IP65 enclosure rating Care must be taken to insure the enclosure is not damaged due to mishandling etc which could compromise the gastight seal If the enclosure is damaged the unit must be returned to the manufacturer for repair Do not open any plates or connections of the housing that are not described in this manual The O rings gaskets are an integral part of the gas tight seal If any access plate is removed the O ring should be inspected before re installing the plate to insure it has not been damaged If visible damage is apparent the O ring must be replaced The unit can be returned to the manufacturer for repair or an O ring kit can be ordered for field replacement All components and interconnects in the Wolverine Ill industrial computers are firmly secured during the assembly process It is not necessary to inspect the internal components If internal damage is suspected the unit should be returned to the manufacturer for repair October 2014 31 Chapter 5 Field Maintenance Wolverine II Agency Approvals and Regulations 5 2 Field Serviceable Components Warning The Field Maintenance procedures must be performed in a non hazard
49. the four fan support screws as marked in Figure 30 below Fan Connectors S ES UE Le NOTE UT S O o S Gell elle J le A 80 LJ e ie e Screws Screws Figure 30 Fans Take the fan assemblies off When mounting the new ones first insert the shackle at the bottom side of the fan assemblies into the display mount Then secure the fan assemblies with the four screws and plug the connectors in Re install the Front Plate as described in section 5 8 2 Installing the Front Plate October 2014 43 AppendixA Wolverine IIl Agency Approvals and Regulations A 1 Agency Approvals ae Agency Standard N A Safety for ITE Equipment for Conforms to STD UL60950 1 use in Hazardous Locations ee Conforms to STD UL60950 22 Class 1 Division 2 Group ABCD ff Conforms to STD ISA12 12 01 Certifies to CSA STD C22 2 No 60950 1 Certifies to CSA STD C22 2 No 60950 22 Certifies to CSA STD C22 2 No 213 Low Voltage Directive Self Declaration in accordance with European Safety for Industrial European LVD Directive Control Equipment 2006 95 EC Independent 3rd party assessment Electromagnetic Compatibility Self Declaration in accordance with Directive European EMC Directive 2004 108 EC European EMC for Industrial Independent 3rd party assessment Control Equipment FCC 47 Part 15 Subpa
50. the gland plate and e atube of Dow Corning DC4 silicon grease To install the Gland Plate 1 Ensure that the O ring Is in its groove and is not damaged Further ensure that the flange of the Gland Plate and the 1 0 Panel are clean 2 Apply a thin layer of DC4 silicon grease from DOW CORNING on the O ring This prevents the O ring from sticking For replacement O rings see page 33 3 Place the Gland Plate on the unit and tighten the captive screws to 0 8 Nm 7 Ibf in to ensure the unit is sealed correctly to maintain the hazardous location certifications and the IP66 enclosure rating 5 4 4 Bonding Connect the external bonding stud below the Gland Plate to a minimum 4 mm bonding wire It has an M4 thread Use means such as a ring terminal to ensure proper connection Warning The nut with washers should always be installed even if no ground connection is present to ensure resistance to impact of the case For example this situation could occur during transportation of the device 5 4 5 Replacing Fuses There is one user serviceable fuse on the back 1 0 plate The Gland Plate must be removed to access the fuse holder Fuse sizes and required replacements are listed below Table 26 Fuses Model Fuse Size GE Intelligent Platforms Part No Wolverine III AC 8 4250Vac 5x20 mm_ WV3SPFUSEACO Fast Acting Ceramic Tube Wolverine III DC 2904 250Vac 125Vdc_ WV3SPFUSEDCO Fast Blow 3AB 5 5 Replacement of the Gland Pl
51. tors and Cabling Wolverine III Agency Approvals and Regulations Caution When operating the Wolverine III in a hazardous environment all cabling with the exception of the WLAN antennas must access the 1 0 Panel through the Gland Plate Gland bland 2X 7x D 6 mm 12 mm D 4 mm 8 mm D 0 236 inch 0472 inch D 0 157 inch 0315 inch Wlan antennas 2x SMA M3 captive screw 15x use PH1 screw driver 0 8 Nm 7 lbf in A Do not lock USB bland Plate Figure 15 Gland Plate Warning Modification of the Gland Plate invalidates enclosure protection and the ATEX certification 3 1 1 Removing the Gland Plate To remove the Gland Plate 1 Loosen the 15 captive screws that secure the Gland Plate to the unit as shown in Figure 15 2 Disengage the Gland Plate from the unit being careful not to strain the cable connecting the USB gland to the USB1 port 3 1 2 Routing Cables through the Gland Plate All plugs connected to the 1 0 Plate must be protected from unplugging by shock and vibration Use securing means of the plugs when available and glue all others where securing means are not available 3 1 3 Torque Values for Cable Glands Torque values for cable glands are determined by gland type cable type and diameter For torque values refer to the manufacturer s instructions for the cable glands 16 Wolverine III Industrial Displ
52. unt standard which defines a variety of means for mounting flat panel monitors televisions and other displays to stands or wall mounts The Wolverine III conforms to VESA MIS D which requires four screw attachment holes on the panel back in a 75 mm or 100 mm square pattern The Wolverine III has M6 screw holes matching both patterns allowing its use with a wide range of commercially available wall mounts desk mounts swing arms articulated arms and so forth VESA MIS D 100 mm mounting holes M6 8 mm depth VESA MIS D 75 mm mounting holes M6 8 mm depth Figure 8 Wolverine III VESA Mount Option 10 Wolverine III Industrial Display Computer Hardware Reference Manual GFK 2789D Chapter 2 Getting Started 2 3 9 Floor Mounting GFK 2789D The Wolverine Ill can be floor mounted using the optional WV3ACCFLRMT floor stand This stand pictured at right with with the Wolverine III installed along with the optional keyboard tray and visor provides adjustments for the height rotation and tilt of the screen It is contructed of stainless steel Installation of the Floor Stand The floor stand base is 250 mm 9 84 in in diameter It is provided with eight 18 mm 0 71 in mounting holes arranged in a 200 mm 7 87 in circle as shown in the figure below for mounting to the floor or other flat surface 0250 mm 9 84 in 200 mm 7 87 in 18 mm 0 71 in Figure 10 Wolverine III Floor Stand Base Figure 9 Wo

GFK2789D WV3 HW Ref Manual

Contents

Download Pdf Manuals

Related Search

Related Contents