Installation Instructions
Contents
1. date of purchase K ryakyn makes no warranty of any kind in regard to other manufacturer s products distributed by K ryakyn K ryakyn will pass on all warranties made by the manufacturer and where possible will expedite the claim on behalf of the customer but ultimately responsibility for disposition of the warranty claim lies with the manufacturer ABOUT OUR CATALOG You ll find all our innovations for H D GL and Metric Cruisers in our annual catalogs Order online today select the CATALOGS icon Each K ryakyn product comes with a Proof of Purchase good for a complimentary catalog Details in packaging Be sure to ask your local dealer about other K ryakyn products the motorcycle parts and accessories designed for riders by riders 2005 K ryakyn USA All Rights reserved INSTALLATION Parts Included 4 Luggage Rack Spacer 1 Hardware Kit including 2 10 24 x 2 BSCS 2 10 24 x 1 3 4 BSCS 4 Spacer 2 x 75 x 125 4 Spacer 2 x 1 00 x 125 4 1 4 SAE Flat washer 1 Installation Instructions Please read and understand entire instructions before starting installation thank you for choosIng k ryakyn Please note It is the installers responsibility to make sure all fasteners including pre assembled are tightened before operation of motorcycle K ryakyn will not warranty components that are lost due to improper installation Periodic maintenance may be requ2. CUSTOMER SERVICE 877 370 3604 toll free INSTALLATION QUESTIONS techsupport kuryakyn com or call 715 247 2983 LIMITED WARRANTY K ryakyn warrants that any K ryakyn products sold hereunder shall be free of defects in materials and workmanship for a period of one 1 year from the date of purchase by the consumer excepting the fol lowing provisions K ryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product s The product must be properly installed maintained and operated under normal conditions K ryakyn makes no warranty expressed or implied with respect to any gold plated products K ryakyn shall not be liable for any consequential and incidental damages including labor and paint resulting from failure of a K ryakyn product failure to deliver delay in delivery delivery in noncon forming condition or for any breech of contract or duty between K ryakyn and a customer K ryakyn products are often intended for use in specific applications K ryakyn makes no warranty if a K ryakyn product is used in applications other than intended K ryakyn electrical products are warranted for one 1 year from the date of purchase by the consumer Components of K ryakyn products containing L E D s will be warranted for defects in materials and workmanship for 3 years from the
3. P 7 Remove the existing luggage rack and hardware save for later use It is recommended that the existing rack mount holes in the trunk lid be enlarged with a 1 4 drill bit to allow for alignment and ease of installation note For installation where a trunk spoiler is already installed ensure that there is enough clearance to install rack risers before drilling any holes steP 8 Insert a 1 3 4 screw washer and small rubber spacer through the underside of the trunk lid in one of the front holes See FIG 1 steP 9 Install a large rubber spacer and rack riser over the protruding end of the screw on the topside of the trunk lid See PIC 3 PIC 4 and FIG 1 steP 10 Repeat STEP 8 and STEP 9 for the other front hole steP 11 Carefully hold the rack in position and begin the threads of the screws into the rack do not fully tighten the screws Allow the rack to hang while the rear screws are prepared See PIC 5 steP 12 Install a 2 screw washer small rubber spacer through one of the rear holes in the trunk lid steP 13 Place large rubber spacer and rack riser over the protruding end of the screw repeat for the other side steP 14 Thread the rear screws into the rack Do not fully tighten screws steP 15 Close trunk lid center rack on lid steP 16 Carefully open the lid tighten screws steP 17 Reinstall trunk lid underside reconnect multi pin connector steP 18 Reinstall 15 screws securing trunk lid underside to l
4. id steP 19 Reinstall latch rings and screws steP 20 Check for proper lid operation Re connect the battery Ride On Page 2 l u g g a g e r a c k r I s e r s InstallatIon Page 2 PIc 2 multI PIn connector dePress tab and Pull out PIc 3 large rubber sPacer rack rIser PIc 4 rack rIser large rubber sPacer screw ProtrudIng from under sIde of trunk PIc 5 do not tIghten screws all the way let hang In front hole fIg 1 screw washer small rubber sPacer trunk lId large rubber sPacer rack rIser rack leg
5. ired tools suggested Phillips screwdriver set of hex wrenches 1 4 drill bit and drill ATTEnTIOn A factory service manual may be helpful in performing this installation Do not attempt to perform this installation if you are not confident in your ability to complete all steps in the procedure consult a trained technician ATTEnTIOn This procedure requires making permanent modifications to the trunk lid this may void your warranty Consult your dealer for more information CAUTIOn AvOID POTEnTIAL ELECTRICAL SHOCK BE SURE TO DISCOnnECT THE BATTERY BEFORE STARTInG THIS PROCEDURE Procedure steP 1 Park motorcycle on a hard level surface Shut the ignition off If equipped put the motorcycle on center stand steP 2 Disconnect the battery steP 3 Open the top trunk lid remove the 15 screws securing the plastic underside of the lid Save the hardware for later use See PIC 1 steP 4 Remove the two screws on each latch ring See PIC 1 cont fIts all 01 uP gl1800 s for use wIth k ryakyn luggage rack P n 7151 unIversal fIt aPPlIcatIon on 1 2 tube rack legs 7154 11GL 1106 l u g g a g e r a c k r I s e r s 715 4 PIc 1 screws securIng undersIde of lId are marked wIth an x x x x x x x x x x x x x x x x latch rIngs InstallatIon steP 5 Pull the trunk lid underside down disconnect the multi pin connector See PIC 2 steP 6 Set aside the trunk lid underside ste
Download Pdf Manuals
Related Search