Air Wing Saddlebag Lid Rail Lights Instruction - Harley
Contents
1. for Kit 68286 10 Light assembly red lens 2 for Kit 68388 10 68488 10 Note Each light assembly includes Items 2 and 3 2 Socket terminal 3 73191 96 3 e Socket housing three way 73153 96BK 4 Screw socket head 4 Not sold separately 8 32 x 0 31 in 8 0 mm long 5 Grommet 2 11410 6 Clip adhesive backed 12 10102 7 Wire harness 70549 99 8 Cable strap 6 10006 9 Dielectric grease packet 76001 04 Items mentioned in text but not included in kit A Air Wing saddlebag rail Hole in side of saddlebag rail mounting post Left rear saddlebag rail mounting pad Left rear saddlebag rail nylon washer Left rear saddlebag rail plain washer Hex head hollow screw Q nim olo w Saddlebag lid Figure 3 Service Parts Air Wing Saddlebag Lid Rail Light J04853 Kits 3of32. Connect the saddlebag rail light adapter harness to the vehicle harness accessory connector 4 Connect the left and right saddlebag rail light wires to the adapter harness Organize the wires neatly alongside the frame rails and secure to the frame with cable straps 6 Turn the ignition key switch to IGNITION but do not start the motorcycle 20f3 Test the saddlebag rail lights and the motorcycle lamps for proper operation a With the ignition switch on the LEDs in each saddlebag rail light should be illuminated along with the vehicle tail lamp s When either the brake hand lever of foot pedal are activated the LEDs in each saddlebag rail light should noticeably brighten along with the vehicle stop lamp s When either turn signal switch is activated the LEDs in each saddlebag rail light should remain lit steadily and not flash Turn the ignition key switch to OFF Both saddlebag rail lights should turn off immediately along with the vehicle tail lamp s WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 7 Refer to the service manual and follow instructions to install the seat SERVICE PARTS Table 1 Service Parts Item Description Quantity Part Number Light assembly smoked lens 68106 10 2
3. post 4 Install the light to the underside of the saddlebag rail rear cross bar with two screws 4 from the kit Tighten the screws gt securely 5 Insert the light wires through the left rear saddlebag rail mounting pad C and the left rear hole H in the saddlebag lid G Assemble the saddlebag rail to the lid per the instructions in the Air Wing Saddlebag Rail Kit feeding the wires through the left rear saddlebag rail nylon washer D plain washer E and the hex head hollow screw F Tighten the two Phillips head screws to 27 31 in Ibs 3 1 3 5 Nm Tighten the hex head hollow screw to 30 50 in Ibs 3 4 5 6 Nm 1 of 3 AU is06151 upper edge of saddlebag 2 Grommet 3 Adhesive backed clip 3 Figure 1 Wire Routing Inside Saddlebag 6 See Figure 1 Measure approximately two inches 51 mm down 1 from the upper edge of the saddlebag just for ward of the shock absorber bulge as shown and affix a strip of masking tape to the inside wall of the saddlebag at that location Mark the location on the tape with a center punch then a drill a 1 16 inch 2 mm diameter pilot hole through the saddlebag wall b Enlarge the hole using a 3 8 inch 10 mm drill bit 7 Remove the tape Lightly sand to remove burrs and sharp edges Clean the inside and outside saddlebag surfaces of tape and drilling residue with a mixture of 50 70 isopropyl alcohol and 30 50 distilled water Allow to dry thoro
4. cMOTOR HARLEY DAVIDSON WY J04853 INSTRUCTIONS REV 2009 05 15 AIR WING SADDLEBAG LID RAIL LIGHTS GENERAL Kit Numbers 68286 10 68388 10 Models This kit fits 1993 and later FL Touring model motorcycles with Color Matched Hard Saddlebags This kit is not compatible with previously installed saddlebag lid organizers Additional Parts Required Prior or concurrent installation of Air Wing Saddlebag Rails is required for proper installation of this kit on this model motor cycle See the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only for the available Saddlebag Rail Kit and model fitment information AWARNING The rider s safety depends upon the correct installation of this kit If the procedure is not within your capabilities or you do not have the correct tools have a Harley Dav idson dealer perform the installation Improper installation of this kit could result in death or serious injury 00308a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is available from a Harley Davidson dealer Electrical Overload NOTICE It is possible to overload your motorcycle s charging system by adding too many electrical accessories If your combined electrical accessories operating at any one time consume more electrical current than your vehicle s charging system can produce the electrical con
5. sumption can discharge the battery and cause vehicle electrical system damage See a Harley Davidson dealer for advice about the amount of current consumed by additional electrical accessories or for necessary wiring changes 00211b J04853 WARNING When installing any electrical accessory be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modi fied Exceeding the maximum amperage can lead to elec trical failures which could result in death or serious injury 00310a This Air Wing Saddlebag Lid Rail Lights kit requires up to 50 mA additional current from the electrical system Kit Contents See Figure 3 and Table 1 INSTALLATION 1 If saddlebag rails have not yet been installed Perform the Air Wing Saddlebag Rail installation up to the point of final assembly of the rails to the saddlebag lids If saddlebag rails are already installed Open one saddlebag and remove all loose contents Remove one saddlebag from the vehicle per service manual instructions From the underside of the saddlebag lid remove the fasteners retaining the saddlebag rail to the lid Note fastener position and save all components for installation 2 ALL installations See Figure 3 Obtain a saddlebag rail light assembly 1 from the kit 3 Insert the light wires through the hole B in the side of the saddlebag rail A mounting post and out through the bottom of the
6. ughly Install one of the rubber grommets 2 in the hole Attach the light wires to the inside of the saddlebag bottom with adhesive backed clips 3 as shown Route the wires up the inner wall of the saddlebag and out through the grommet 10 Repeat for the remaining saddlebag rail light assembly and saddlebag 11 Install the saddlebags to the vehicle per service manual instructions WIRING 1 Refer to the service manual and follow the instructions given to remove the seat J04853 2 See Figure 3 Obtain six socket terminals 2 and two socket housings 3 from the kit Refer to the service manual and follow the instructions to crimp the terminals onto the saddlebag rail light wires 3 Insert the wires and terminals from one saddlebag rail light into one of the socket housings a Insert the blue wire into cavity 1 b Insert the red yellow wire into cavity 2 c Insert the black wire into cavity 3 Repeat for the remaining wires and socket housing 4 Obtain the adapter harness 7 from the kit See Figure 2 Locate the four way accessory connector 4 in the area under the seat Remove the plug from the accessory connector NOTE If the accessory connector is already in use a Switched Circuit Adapter Harness Part No 70264 94A is available from a Harley Davidson dealer to provide an additional connection point is06153 Figure 2 Accessory Connector 4 Location Under Seat 5
Download Pdf Manuals
Related Search