Home

ZM303 User`s Manual - Avery Weigh

1. Definition Gross zero band this is a configured value that defines a window around gross zero This is used in several ways in different applications The three types of tare are explained below Using Pushbutton Tare To perform a net weighment using pushbutton tare power up the unit and follow these steps 1 With no weight on the scale if the display does not read 0 press ZERO 0 is displayed and the center of zero annunciator lights 2 Place item to be tared on the scale Weight is displayed 3 Press TARE 0 is displayed and the NET annunciator lights 4 Place material to be weighed into or on the tared item on the scale Net weight of material is displayed 5 Repeatedly press SELECT to view the gross tare and net values 6 If repeated weighments use the same tared item you do not need to establish a new tare value as described in step 2 and 3 To manually clear a tare weight remove all weight from the scale and press TARE ZM303 Indicator User Instructions 3 1 General weighing application Using Entered Tare To perform a net weighment using entered tare the following steps describe a typical operation 1 With no weight on the scale if the display does not read 0 press ZERO 0 is displayed and the center of zero annunciator lights 2 Key in the tare value of the container or box that will be used to hold the material that requires a net weight value and press TARE T
2. If the indicator is connected to an ethernet network the values displayed will be the current assigned addresses 10 From oPtion press UNITS EnEt is displayed Use this item to view the values for the IP Subnet Gateway and MAC addresses Press SELECT iP is displayed Use this item to view the four part IP address Press SELECT 1 XXX is displayed This is first octet of the IP address Press ZERO 2 XXX is displayed This is second octet of the IP address Press ZERO 3 XXX is displayed This is third octet of the IP address Press ZERO 4 XXX is displayed This is fourth octet of the IP address Press ZERO iP is displayed Press UNITS Subnet is displayed Repeat this sequence of key presses for the Subnet Gateway and MAC addresses When finished press TARE EnEt is displayed 39 Menus 4 6 6 Dload About y Boot gt Firm gt App gt Serial gt Option gt Enet gt Dload 40 1 10 11 From EnEt press UNITS dLoAd is displayed This stands for download Under SSEriAL you can view the serial number of the software application that created the configuration file Under dSEriAL you can view the serial number of the software application that downloaded the configuration file This is used for security and licensing purposes Press SELECT SSEFriAL is displayed Press SELECT The 1st half of the serial number of the creating application of the
3. 14 15 7 1 3 Battery Press UNITS rESEt is displayed Use this to reset the all the preset tares to the factory default of 0 Press SELECT no is displayed Press ZERO to abort the reset or press UNITS YES is displayed Press ZERO to reset the settings to factory defaults rESEt is displayed Press TARE tArE is displayed Super y Setpoint gt Tare gt Battery 1 50 Press UNITS bAttErY is displayed Use this to enable the battery and to set a timeout length in minutes If this time expires with no scale or keypad activity the battery will be shut off ZM303 Indicator User Instructions 7 1 General Weighing application supervisor menu Enable Battery y Enable Only enable the battery and set the tMout value if the ZQ BAT option is being used If a battery use is enabled setpoint output 3 cannot be used for setpoints in checkweighing or batching applications It is used as a shutoff signal to the ZQ BAT battery option 2 Press SELECT EnAbLE is displayed Choices are oFF and on Choose oFF to disable battery usage Choose on to enable battery usage 3 Press UNITS to toggle between the choices and when your choice is displayed press ZERO to accept EnAbLE is displayed Timeout Battery y Enable gt Timeout 4 Press UNITS tMout is displayed This stands for timeout Use this to set the length of time before inactivity of the scale and keypad cause
4. Manual No 2 Speed Ingred Indep Fil DSC SELECT Y m H m3 i Key Key Key PRINT lt in in in value value value Nore UNITS gt ZERO __ Units H Select HH Tare Zero Sample 4 F1 Target Start F1 Escape or A Stop ID Setup Under Over HH Accu H User Figure 7 5 Supervisor menu for the Batching application Follow these steps to set the items in the Supervisor menu General Weighing application supervisor menu on page 46 Go there for information 19944 E The Setpnt Tare and bAttErY submenus in Figure 7 5 are the same as described in on those submenus The unique submenus to this application are described below 7 5 1 Batch Super y Setpoint gt Tare gt Batch 1 With the Batching application active access the Supervisor menu using password 1793 Refer to Accessing the menus on page 32 for instructions From SuPEr press SELECT SEtPnt is displayed ZM303 Indicator User Instructions 63 Supervisor menu 2 Press UNITS twice bAtch is displayed Use this to set the items relating to batching Set the type of batch operation tYPE Select auto or manual operation ModE Set gross or net display mode diSP Set the conditions for preact PrEAct Select negative filling operation nEG FiL Type Batch y Type 3 Press SELECT tYPE is displayed There are 4 choices under Type 2 SPEEd iNGrEd iNdEP and FiL dSc Each is explained below 2SPEEd Choose 2 speed when
5. Under On Over target weight target target weight Figure 3 2 Checkweighing bargraph There are two ways to set a target weight e Weigh the target object If you use this method the acceptable weight will be the actual weight of the target sample a predefined range default is 1 division O Key in upper and lower weight limits If you use this method the acceptable weight is any weight which falls between the upper and lower limits Each of these is explained below the net weight is considered for checkweighing If there is no tare gross weight is SEC lt The checkweighing annunciators are based off of net weight so if a tare is active only used as the basis for the annunciators 24 ZM303 Indicator User Instructions 3 4 Checkweighing application 3 4 4 Weighing a target object With the indicator in checkweighing mode follow these steps to set a target by weighing an object 1 Press ZERO to zero the scale if necessary 2 Enter a tare if necessary Refer to Net weighing on page 76 for instructions 3 Place an object of the desired weight on the scale and press TARGET The weight is displayed and the middle bargraph segment lights as well as the SP2 annunciator Asco R F z The acceptable target window is a range from Target Object weight a predefined range entered in a password protected menu The farther the weight is from the target weight more over or under bargraph segments wil
6. Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions ATTENTION II y a danger d explosion s il y a remplacement incorrect de la batterie remplacer uniquement avec une batterie du m me type ou d un type quivalent recommand par le constructeur Mettre au rebut les batteries usag es conform ment aux instructions du fabricant 1 2 2 Wet conditions Under wet conditions the plug must be connected to the final branch circuit via an appropriate socket receptacle designed for washdown use Installations within the USA should use a cover that meets NEMA 3R specifications as required by the National Electrical Code under section 410 57 This allows the unit to be plugged in with a rain tight cover fitted over the plug Installations within Europe must use a socket which provides a minimum of IP56 protection to the plug cable assembly Care must be taken to make sure that the degree of protection provided by the socket is suitable for the environment 1 3 Routine maintenance IMPORTANT This equipment must be routinely checked for proper operation and calibration Application and usage will determine the frequency of calibration required for safe operation Always isolate the indicator from the power supply before starting any routine maintenance to avoid the possibility of electric shock ZM303 Indicator User Ins
7. configuration file is displayed Press ZERO to show the 2nd half Press F1 SSEFriAL is displayed Press UNITS dSEFriAL is displayed Press SELECT The 1st half of the serial number of the downloading application of the configuration file was downloaded to is displayed Press ZERO to show the 2nd half Press F1 dSEFriAL is displayed Press TARE until About is displayed To exit the menu see Exiting the menus on page 33 ZM303 Indicator User Instructions 4 7 Audit menu 4 7 Audit menu The Audit menu is shown in Figure 4 4 SELECT Y TARE A PRINT lt UNITS p gt ZERO _ F1 Escapeor A Displays Displays number of number of configurations calibrations Figure 4 4 Audit menu Use this menu to display audit counters for configuration and calibration and to print the information Each is explained below 4 7 1 Counter Audit y Counter 1 Access the Audit menu and press SELECT countEr is displayed This has two counters that tell you how many times the indicator has been configured and calibrated 2 Press SELECT conFig is displayed 3 Press SELECT again A number appears showing how many times the indicator has been configured 4 Press ZERO conFig is displayed 5 Press UNITS cALib is displayed 6 Press SELECT A number appears showing how many times the indicator has been calibrated 7 Press ZERO cALib is displayed 8 Press TARE
8. countEr is displayed ZM303 Indicator User Instructions 41 Menus 4 7 2 Print Audit y Counter gt Print 1 From countEr press UNITS Print is displayed 2 Press SELECT Port1 is displayed This is the first of three choices Port 1 Port 2 or uSb Use these to select which port to print the audit report through 3 Press UNITS to scroll through the choices and press ZERO when your choice is displayed The audit log is printed through the chosen port and Print is displayed 4 This completes the Audit menu To exit the menu see Exiting the menus on page 33 42 ZM303 Indicator User Instructions 5 1 Default print formats 5 Communications The ZM303 can communicate through these ports O Serial Ethernet e USB O Wireless 802 119 5 1 Default print formats Below are examples of the default formats that are available Gross 272 04 1b General Weighing Format 1 Tare 95 88 1b Net 176 16 1b Transaction Gross 272 Accumulated Gen Weigh Format 2 Tare 95 Net 176 Counting Format 3 Count 176 Checkweighing Format 4 Net 176 16 1b Batching Format 5 G 272 04 1b Peak Weighing Format 6 Peak Gross 1000 02 1b Remote Display Format 7 272 04 1b G The indicator can be configured for many other outputs to match the application ZM303 Indicator User Instructions 43 Error messages 6 Error messages The following error messages may be displayed du
9. gt In 10 Repeat steps 7 through 9 for out2 and out3 Press UNITS when finished in1 is displayed This stands for input 1 Use this to assign a function to input 1 when an external switch is tripped Default choice is nonE The choices are listed in Figure 7 1 Inputs and Outputs must be enabled ON in a separate password protected menu Some input choices will not apply in the application that is active 11 From in1 press SELECT The current choice is displayed 12 Press UNITS to scroll through the choices and when your choice is displayed press ZERO to accept in1 is displayed 13 Press UNITS in2 is displayed 14 Repeat steps 11 through 13 for in2 and in3 Press TARE when finished Edit is displayed Print Setpoint y Edit gt Print 15 Press UNITS Print is displayed Use this to print the settings under SEtPnt 16 Press SELECT Port 1 is displayed 17 Press F1 to abort the print process or press UNITS to scroll to the desired port and press ZERO to print the information Print is displayed after either action ZM303 Indicator User Instructions 7 1 General Weighing application supervisor menu Reset Setpoint y Edit gt Print gt Reset 18 19 20 21 22 7 1 2 Tare Super y Setpoint gt Tare 1 Press UNITS rESEt is displayed Use this to reset the settings under Edit to factory defaults Press SELECT no is displayed Press ZERO to abort t
10. Under Over H Accu H User Figure 7 3 Supervisor menu for the Count application Follow these steps to set the items in the Supervisor menu CCCG NTA The Setpnt Tare and bAttErY submenus in Figure 7 3 are the same as described in General Weighing application supervisor menu on page 46 Go there for information on those submenus The unique submenus to this application are described below The cnt Acc submenu is the same described in the Accum submenu in the Accumulator application Refer to step 3 on page 53 56 ZM303 Indicator User Instructions 7 3 Counting application supervisor menu 7 3 1 Count Super y Setpoint gt Tare gt Count 1 With the Count application active access the Supervisor menu using password 1793 Refer to Accessing the menus on page 32 for instructions From SuPEr press SELECT SEtPnt is displayed 2 Press UNITS twice count is displayed Use this to set the items relating to counting O Select between bulk and dribble mode e Enable Disable the ability to print the count total Prt tot O Key ina print format number for printing the total count information tot FMt e Enable Disable the ability to clear the total count information when the total is printed clr tot The following steps describe the procedure to set these items Mode Count Y Mode 3 Press SELECT MOdE is displayed There are two modes for sampling buLK and dribbLE Bulk In bulk sampling you place the
11. battery power to be shutoff Values between 1 and 3600 minutes are valid 5 Press SELECT A numeric entry screen appears 6 Key in a value in minutes and press ZERO to accept tMout is displayed 7 This completes the Supervisor menu for General Weighing Repeatedly press TARE until the indicator returns to normal weighing mode The current weight value is displayed ZM303 Indicator User Instructions 51 Supervisor menu 7 2 Accumulator application supervisor menu Figure 7 2 shows the Supervisor menu when you are in the Accumulator application SELECT Y TARE A PRINT a Appears only if Preset UNITS gt Tare is enabled E ZERO gata F1 Escapeor A 1 3600 minutes Enter Print format for Total operation Bold boxes and text denote defaults o Key Key Key in in in value value value Tare D Under user Figure 7 2 Supervisor menu for the Accumulator application Select Follow these steps to set the items in the Supervisor menu General Weighing application supervisor menu on page 46 Go there for information CC El The Setpnt Tare and bAttErY submenus in Figure 7 2 are the same as described in on those submenus The unique submenus to this application are described below 52 ZM303 Indicator User Instructions 7 2 1 Accumulator Super y Setpoint gt Tare gt Accum 7 2 Accumulator application superviso
12. format The PRINT annunciator lights briefly 4 Remove weight from the scale Weight must return to inside the gross zero band before another print and accumulation can be recorded O Repeat steps 2 through 4 for each weighment you want to accumulate If enabled press and hold PRINT for three seconds to print and or clear the active accumulator values These functions are enabled or disabled in a password protected menu 20 ZM303 Indicator User Instructions 3 3 Counting application 3 3 Counting application This section applies if Counting is active 3 3 1 SELECT key default function In the Counting application you can view the gross net tare count and piece weight display values by repeatedly pressing SELECT 3 3 2 Special key functions The following keys have an extra function in this application SAMPLE Press SAMPLE to perform the sample operation as described below in the Dribble and Bulk sections Press and hold SAMPLE to perform the piece weight entry as described below F1 F1 works the same as the SAMPLE key when pressed 3 3 3 Sample operation There are two types of sampling to select from bulk and dribble Either type is selectable under a password protected menu Dribble sampling In this sampling method you can count out the specified number of items onto the scale and when you are ready press the SAMPLE or F1 key and the scale starts to calculate piece weight and then shows the count Bul
13. occur and the fill cutoffs are based on actual Gross weight If PREACT is set to AUTO this only effects the cutoff value of Out 2 See details of PREACT below If NEG FILL is set to YES then DISP should be set to NET so that an autotare occurs prior to start and the cutoffs will be based on negative entered values for Out 1 and Out 2 ZM303 Indicator User Instructions 7 5 Batching application supervisor menu Ingredient If MODE is set to AUTO the batch process will continue until the final ingredient is completed Between each ingredient there will be a slight delay to allow for motion final weight and preact calculations If MODE is set to MANUAL this requires that you press F1 or START between each ingredient to complete the fill cycle If DISP is set to NET an autotare will occur prior to each ingredient and the Out 1 2 and 3 fill weights will be based on Net weight If DISP is set to GROSS no autotare will occur and the Out 1 2 and 3 fill weights would be based on the Gross weight of the accumulated ingredients If Ingredient 1 amountis 10 Ingredient 2 amount is 20 and ingredient 3 amount is 30 then you would enter Out 1 10 Out 2 30 10 20 and Out 3 60 10 20 30 Output cutoffs are based on the actual displayed Gross weight so if inaccurate amounts of ingredient are experienced during the batch then it may affect the amount of each subsequent ingredient that is added If PREACT is set to AUTO then it wi
14. to return to the boot display 4 6 2 Firm and App About y Boot gt Firm and App 1 From boot press UNITS FirM is displayed This stands for firmware 2 Repeat the same pattern of key presses in steps 2 through 7 to view the part number and version for the FirM and APP menu items 4 6 3 Serial About y Boot gt Firm gt App gt Serial 1 With APP displayed press UNITS SEFriAL is displayed 2 Press SELECT The indicator s serial number is displayed 3 Press TARE to return to the SEriAL display 4 6 4 Option About y Boot gt Firm gt App gt Serial gt Option 1 From SEriAL press UNITS oPtion is displayed 2 Press SELECT VErSion is displayed This stands for the software version of the currently installed option card This can be useful service information 3 To view the version press SELECT The software version number is shown 4 Press ZERO oPtion is displayed 2 Press UNITS tYPE is displayed This stands for the type of option card installed The four option cards are Analog 802 11g wireless USB d and Current Loop RS485 RS422 6 Press SELECT The currently installed option card name is displayed 38 ZM303 Indicator User Instructions 4 6 5 Enet 7 8 4 6 About menu Press ZERO tYPE is displayed Press TARE oPtion is displayed About y Boot gt Firm gt App gt Serial gt Option gt Enet E ZM303 Indicator User Instructions
15. unSEALE or SEALEd is displayed This is the status of the physical seal inside the indicator If the unit is sealed no changes can be made to the configuration of the indicator Press F1 to return to the SEAL display To exit the menu see Exiting the menus on page 33 ZM303 Indicator User Instructions 4 6 About menu 4 6 About menu The About menu is shown in Figure 4 3 Option Number IP Subnet Gateway Mac Displays Displays Displays Displays Displays the Displays the IP address Subnet Gateway Mac application application info info info part number version Type Version number Parino Displaysthe Displays the SELECT Y firmware firmware A part number version number TARE A r PRINT K Partno Version UNITS gt Displaysthe Displaysthe _ bootloader bootloader ZERO _ PN version F1 Escapeor A Figure 4 3 About menu Use this menu to display information about the various items shown in Figure 4 3 Each is explained below 4 6 1 Boot About y Boot 1 Access the About menu and press SELECT boot is displayed 2 Press SELECT PArtno is displayed 3 Press SELECT The bootloader PN is displayed 4 Press ZERO to return to the PArtno display 5 Press UNITS VErSion is displayed 6 Press SELECT The version number of the bootloader is displayed ZM303 Indicator User Instructions 37 Menus 7 Press ZERO to return to the VErSion display 8 Press TARE
16. will light during operation to inform the user of the weighing mode active unit of measure etc Table 2 1 Circle Annunciator assignments Annunciator Indicates Circle 1 left most Network activity Circle 2 Custom unit Circle 3 Pieceweight Circle 3 amp 4 Minimum Circle 4 8 5 Maximum ZM303 Indicator User Instructions 13 Introduction 2 2 Powering up the ZM303 The indicator is always active as long as power is received Power can be supplied by AC power cord connected to a properly grounded outlet 100 VAC 240 VAC 50 or 60 Hz e Optional external battery pack with 4 D cells 12 hr operation with one loadcell 11 hr with four loadcells AC to DC power converter 12 to 36 VDC 2 3 Entering a negative number To enter a negative number press the C key to clear the current value from the display With only one digit displayed press SELECT The first character will be the negative sign Enter the rest of the digits normally 14 ZM303 Indicator User Instructions 3 1 General weighing application 3 Indicator applications This indicator has several weighing applications that can be enabled through a password protected menu Only one application can be enabled at a time The applications available are General Weighing explained on page 15 Accumulator explained on page 20 Parts Counting explained on page 21 Checkweighing explained on page 24 e Batching explained on page 2
17. you have one ingredient with a speed control device iNGrEd Choose ingredient for sequential filling for up to 3 products at a single speed iNdEP Choose independent when the filling process is run based on the values set for the outputs FiL dSc Choose fill discharge when performing a fill operation negative weight from something like a hopper scale See Notes on batching on page 66 for information about settings for each of these types of batching 4 Press SELECT The current setting is displayed 5 Press UNITS to scroll through the choices and when your choice is displayed press ZERO to accept tYPE is displayed Mode Batch y Type gt Mode 6 Press UNITS ModE is displayed Mode has two choices Auto or MAnuAL There is a detailed description for each type in the section titled Batching application on page 27 7 Press SELECT The current setting is displayed 8 Press UNITS to toggle between the choices and when your choice is displayed press ZERO to accept ModE is displayed 64 ZM303 Indicator User Instructions 7 5 Batching application supervisor menu Display Batch y Type gt Mode gt Display 9 Press UNITS diSP is displayed Display has two choices NEt or GroSS Each is explained below NEt Choose Net to base batching on net weights GroSS Choose Gross to base batching on gross weights 10 Press SELECT The current setting is displayed 11 Press UNITS to tog
18. 7 Peak Hold explained on page 30 O Remote Display explained on page 31 The indicator comes with the default application called General Weighing active 3 1 General weighing application This section applies if the General Weighing application is active 3 1 1 SELECT key default function In the General Weighing application you can view the gross net and tare display values by repeatedly pressing SELECT 3 1 2 Gross weighing E al To change unit of measure press UNITS To perform gross weighing power up the unit and follow these steps 1 Empty the scale and press ZERO to zero the display 0 is displayed and the center of zero annunciator lights 2 Place item to be weighed on the scale Weight is displayed 3 Repeat steps 1 and 2 ZM303 Indicator User Instructions 15 Indicator applications 3 1 3 Net weighing lt 16 Net weighing is available via three types of tare entry Pushbutton tare When enabled press TARE to tare the weight on the scale Entered tare When enabled key in a tare weight and press TARE to set Preset tare When enabled press TARE to recall a preset tare numbered 1 10 Pushbutton and Entered Tares can be enabled simultaneously If Preset Tare is enabled Pushbutton and Entered Tares are automatically disabled There is an auto tare clear feature If this is enabled after a weighment when the weight falls into the gross zero band tare is cleared to zero
19. Avery Weigh Tronix ns ZM303 Indicator User Instructions AWT35 500722 Issue AA Avery Weigh Tronix LLC 2012 All rights reserved No part of this publication may be reproduced stored in an electronic retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written consent of the copyright owner or as permitted by law or under license Full acknowledgment of the source must be given Avery Weigh Tronix is a registered trade mark of the Avery Weigh Tronix LLC This publication was correct at the time of going to print however Avery Weigh Tronix LLC reserves the right to alter without notice the specification design price or conditions of supply of any product or service at any time All third party brands and product names used within this document are trademarks or registered trademarks of their respective holders ZM303_u_en_500722 book Table of Contents page Chapter 1 General information and warningS oooonnncccnnnnncccccnnnnoccccnno nan nccnn nan roca nora rca 7 About this manual ica airada A A A AA 7 Text CONVENTIONS si a td ai a di dica 7 Special Messages isis ill ile 7 Installation ci A ead a lee ted 7 Safe handling of equipment with batteries cece eee ceceeeeeeneeceeceeeeeeteeeeeteteeesnsnnsaeees 8 Wet CONCISA a dae 8 RI 8 Cleaning the Machine ccc ceeeeeecneceeeeeeeeeeeeeeeeeeeeedheneeeeedddu
20. FMt is displayed This stands for the total print format 7 Press SELECT The current print format number is displayed with a flashing right most digit Default is format 8 ZM303 Indicator User Instructions 53 Supervisor menu 54 8 Press ZERO to accept the existing setting or key in a new format number and press ZERO tot FMt is displayed Clear total Accum y Print Total gt Total Format gt Clear Total 9 Press UNITS cLr tot is displayed This stands for clear total Choose on to enable clearing the accumulated total when printed Choose oFF to disable this function If enabled the total is cleared if the user presses and holds the PRINT key for three seconds The message cLr tot will flash The total is printed prior to clearing if this was enabled in step 5 above 10 Press SELECT The current setting is displayed 11 Press UNITS to toggle between the choices and when your choice is displayed press ZERO to accept cLr tot is displayed Print Accum y Print Total gt Total Format gt Clear Total gt Print 12 Press UNITS Printis displayed This stands for print the accumulation report Choose a port to print the accumulated totals report for all 10 memory channels 13 Press SELECT Port 1 is displayed 14 Press F1 to abort the print process or press UNITS to scroll to the desired port and press ZERO to print the information Print is displayed after either actio
21. From SuPEr press SELECT SEtPnt is displayed Use this to set the function of the setpoint annunciators enter up to three setpoint values select inputs for up to three inputs print the setpoint settings reset all setpoint settings to factory defaults Annunciators Setpoint y Edit Y Annun 2 Press SELECT Edit is displayed 3 Press SELECT Annun is displayed Annun is not included in the Batch application Supervisor menu Skip steps 3 through 5 This stands for annunciators referring to the SP1 SP2 and SP3 setpoint annunciators By default OFF these annunciators are ON when the displayed weight is below the setpoint value or OFF above the setpoint value If you select on the annunciators work in the opposite fashion OFF when below ON when above 4 Press SELECT The current setting is displayed OFF or on 5 Press UNITS to toggle between the choices and when your choice is displayed press ZERO to accept Annun is displayed Outputs Setpoint y Edit Y Annun gt Out 6 Press UNITS out7 is displayed This is the weight value for setpoint 1 7 Press SELECT The current value is displayed with a flashing right digit ZM303 Indicator User Instructions 47 Supervisor menu 48 8 Press ZERO to accept the displayed value or key in a new value and press ZERO to accept out1 is displayed 9 Press UNITS out2 is displayed Inputs Setpoint y Edit Y Annun gt Out
22. are weight is displayed as a negative value and the NET annunciator lights 3 Place the container or box and material to be weighed on the scale Net weight of material is displayed 4 If repeated weighments use the same tared item you do not need to establish a new tare value as described in step 2 5 To remove the tare weight from the scale enter 0 then press TARE The tare is cleared and the scale is in gross weigh mode Using Preset Tare Preset tares are entered in a password protected menu There can be up to 10 tares numbered 1 10 To perform a net weighment using one of the preset tares follow these steps 1 With no weight on the scale if the display does not read 0 press ZERO 0 is displayed and the center of zero annunciator lights 2 Press TARE Tare number entry screen appears 3 Key in the preset tare number and press ZERO Tare weight is displayed as a negative value and the NET annunciator lights 4 Place container or box and material to be weighed on the scale Net weight of material is displayed 5 Repeat step 4 until you are finished using that tare weight E Tare is removed automatically if Auto Tare Clear is enabled To remove the tare weight manually select a preset tare register that has a value of 0 for the tare ZM303 Indicator User Instructions 17 Indicator applications 3 1 4 Using setpoints 18 Rg Setpoints are values weight at which outputs ar
23. ations Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Canada This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Classe A prescrites dans le R glement sur le brouillage radio lectrique edict par le minist re des Communications du Canada European Countries ZM303 Indicator User Instructions 9 General information and warnings 1 8 Declaration of conformity 10 ZM303 Indicator User Instructions 2 Introduction The ZM303 shown in Figure 2 1 is an easy to use indicator for weighing with a numeric keypad The ZM303 comes in three housing types stainless steel aluminum desktop and stainless steel panel mount It comes with one of two display types for indoor or outdoor use The indicator has a USB port two serial COM ports and an Ethernet port Available options are Analog Output Current Loop RS485 RS422 USB Device and Wireless 802 11g internal module cards The indicator also has three logic level inputs with configurable functions and three setpoint outputs See the Specification literature for a full list of s
24. can be full open partially open or closed When the fill starts both SP1 and SP2 are turned on outputs activated which should set the dual speed control to full open Fast speed When the Out 1 value is reached SP1 and Output 1 are turned off and this should set the dual speed control to partial open condition Slow speed When Out 2 value is reached SP2 and Output 2 are turned off to close the control device and complete the fill 1 Press SETUP or press and hold SELECT to access the setpoint editor 2 Set Out1 to the fast fill value and Out 2 to the slow fill value Example To fill a product to 100 Ib with the last 5 Ib on slow fill Out 1 should be set to 95 and Out 2 should be set to 100 3 To start or restart the 2 speed filling process press START or F1 4 To stop the filling process press STOP or F1 F1 toggles the process on and off 3 5 5 Ingredient filling Ingredient filling is for batching up to 3 different ingredients controlled by Out 1 2 and 3 values If Out 2 value is 0 then it operates as a single ingredient filler If Out 3 value is O then it operates as 2 ingredient batcher 1 Press SETUP or press and hold SELECT to access the setpoint editor 2 Set Out1 to the ingredient 1 value Out 2 to the ingredient 2 value and Out 3 to the ingredient 3 value 3 To start or restart the batching process press START or F1 4 To stop the batching process press STOP or F1 F1 toggles the process on and o
25. d boxes and text Tare is enabled denote defaults Setpnt l Tare gE are Check Battery Nal 1 3600 minutes 0 100 0 100 No SELECT y TARE A No PRINT lt 4 UNITS gt ZERO _ F1 Escape or A sop H D H Setup H Under H Over H Accu H User Figure 7 4 Supervisor menu for the Checkweighing application Follow these steps to set the items in the Supervisor menu General Weighing application supervisor menu on page 46 Go there for information on those submenus The one exception is that out1 out2 and out3 are not in the Setpnt menu They do not apply in the Checkweighing application The unique submenus to this application are described below C lt The Setpnt Tare and bAttErY submenus in Figure 7 4 are the same as described in 60 ZM303 Indicator User Instructions 7 4 1 Check 7 4 Checkweighing application supervisor menu Super y Setpoint gt Tare gt Check 1 With the Checkweighing application active access the Supervisor menu using password 1793 Refer to Accessing the menus on page 32 for instructions From SuPEr press SELECT SEtPnt is displayed Press UNITS twice chEcK is displayed This stands for checkweigher Use this to set the items relating to checkweighing Set conditions for using the outputs outPutS Set under divisions for acceptable target weight undrdiv Set over divisions for acceptable target weight oVErdiV Reset the target values to z
26. e oh en Re do 61 Outputs Latch amp UnlatCh ccccceccceccecceceeeeeeeeececeeaeeeeeeeeeeeeeeseneenncaeaeeeeeeeeeees 61 UNGEF GIVISIOMS aeaiee a rt ia sata 61 Over diVISIONS ii A ee We eee 62 Reset seat seets ada 62 Batching application Supervisor MENU ceeeeeeeceeceeceeeeeeeeeeeeceeeeaaeaeeeeeeeeeeesetseeeeaeeas 63 BACA uri hd A AA ae nah aus sa sa Soar EA at 63 TYPE ii dd AA daa 64 Mode nal ld dde celia 64 Display ensia eege ea n a a TPE ES EEAS EA daa 65 PHO CU 5 cose sesso A A A A A A teense 65 Negative fill Aerniesuiiinsorini lec Ae A AA E A EAEN 66 Notes oh batching tii ia 66 A Lee ee ee 66 MoredienE re Tori a a eon as ces ted bea dar sees PA TAAA 67 Independent Setpoints 2 2 2 0 ccccccecceee cee eeeeeeeceeaeceeceeeeeeeeeeeeeesceaaeaeceeeeeeeeeeeeeeeeeee 67 A A ete votet a ar a esd U EE era e NA aa 67 Peak Hold application supervisor MENU cccccceeeeeeeeeeeeeceeceaeceeeeeeeeeeeeseetetseenisaeeess 68 Peak Old Toere tes cali ca tece lind nde RI caer ned hase nade Rarer ee 68 ROL site A nie a A a a ee eee 69 Remote Display application supervisor MENU cceeeeeeeeeeeeeeeceecceeeeeeeeeeeteseeeseeninaeeess 70 ZM303 Indicator User Instructions ZM303 Indicator User Instructions 1 1 About this manual 1 General information and warnings 1 1 About this manual This manual is divided into chapters by the chapter number and the large text at the top of a page Subsections a
27. e triggered automatically Outputs can control relays connected to valves lights other machinery etc Setpoint outputs can be configured in the setpoint menu shown in Figure 3 1 Press SETUP setpoint setpoint setpoint Figure 3 1 Setpoint menu See the note below for an overview of how setpoints function Default Setpoint operation Outputs must be enabled for setpoints to operate See the Service Manual Below Configured Value Outputs are ON Annunciators are ON Above Configured Value Outputs are OFF Annunciators are OFF The annunciator and output will turn off when weight goes above the setpoint for that output and will remain off until the weight falls below the setpoint Follow these steps to configure the outputs 1 With the indicator powered up press SETUP SEtPnt is displayed Refer to the Setpoint menu shown in Figure 3 1 while following the steps below 2 Press SELECT out1 is displayed 3 Press SELECT Current value is displayed with the last digit flashing 4a Key in a value and press ZERO to accept the value out is displayed OR 4b Press UNITS to select the next output out2 is displayed ZM303 Indicator User Instructions 3 1 General weighing application 5 Repeat steps 3 4b for each output 6 Press F1 twice to return to normal weighing mode with the setpoints active 3 1 5 Printing To print the current weight information press PRINT The configured prin
28. e while in normal operating mode Acts as a right arrow key for menu navigation Press the ZERO key to zero the display Acts as an ENTER key to accept a displayed value or function Press the SAMPLE key to setup counting functions Press the START key to start or resume a batching specific action Press the STOP key to stop a batching specific action Press ID to show the current ID value Press and hold ID to enter a new ID value Press the F1 key to select application specific choices Aborts a numeric entry and acts as an ESCAPE key in the menu navigation Also used to display or enter an accumulator channel Press and hold to view the password entry screen for menu access 12 ZM303 Indicator User Instructions 2 1 Front panel Press the SETUP key to access the setpoint editor Press and hold to view the password entry screen for menu access Press the TARGET key setup checkweighing functions TARGET Use the numeric keypad to enter numbers in the appropriate screens Press the C CLEAR key to clear the last entry 2 1 1 Annunciators The annunciators on the display are shown and labeled in Figure 2 3 bargraph center of zero motion Gross weight its of Net weight ee measure Tare weight 4 sl ij preset tare quantity Count Print 7 ee A AA battery i setpoints See Table 2 1 Figure 2 3 Annunciators These annunciators
29. eceeeeeeecseeeedtennedeedeteneededee 9 A ys ccenavndas sapere AEA acpeass tend iea dau A a EAS 9 Sharp objectis A ae a ea ea ed 9 FCC and EMC declarations of compliance cee eeceececeeeeeeeeeeeeeceneecaeeeeeeeeeeeeetsessnsieeeeeees 9 United States cuate 9 Canadas eer ict A IESE AA A A AAA Ra 9 European Countries cion a delete ds 9 Declaration Of Conformity ze n aa eraa raaa ara e a aeaa a alaaa 10 Chapter 2 OOTO aae ce cease deep ena eee ch ee nce Pa eee a gees 11 A AA 12 ANINUMGIALOIS soca ad anos tiene aan taadaat soe eeeeca ote dada globe 13 Powering up the ZM303 coi Shea i at aa hae i ee 14 Entering a negative number ccccceeencccceeeseeceeeeeenenceceneessececseneneneeceeensnecseseeeseneenenenenes 14 Chapter 3 Indicator applications 2200 20 22 cece cececccecece cee ee eee e eet ce eee aeaeeceeeeeeeeeeesedsecaeaaeeeeeseeeeeeeseeseeneenaeeas 15 General weighing application oooonnnnnccnnnnnaniccnnnnncccccnnnnnrrrccnnn nar rnccnnn nar c cnn anar 15 SELECT key default fUNcCtiON aiar E EAT EA AA nana na nar rra 15 GOSS WEIGHING este tion 15 NetwelghINO isidro 16 Using Pushbutton Tar e eo e ed 16 Using Entered Tare ni a 17 Using Pressot Tare oerien eeen EEE ieesd das Meenas lad coeeed dads EEA a ote 17 sng semm s 5 55 nse sedes ces ececrbed packs Unk ori oia 18 PUA ses hens oti teats et eta ents aden eth tee de ete eee 19 Accumulator application ccccccceceeeeeecececncaeceeeeeeeeeeeseesecaaaaaaeaeeeee
30. eee eee eeeeeeeeeeaceeceeeceeeeeeeesegeececeaeceeeeeeeeeeeteees 28 ENVDIsCharde tics evade easel teach ee a ein ee eine 29 Peak hold application ccccceccceecccecceceeeeeeeeeeeeeeaaaeeeceeeeeeeeeseeseseaeaaeaaeeeeeeeeeeeeeeeneennanes 30 SELECT key default fUNCtION ooo eee i raina iaa aaaeei arasen eei aiia 30 Special key functions oo cece eeecccceeeecccceeeeeeecceeteeseeceeeedeseaceeeeeeenaeeeeetesaaeeeesessaaeeedeneeaaees 30 Peak hold Operation Aiste e a eaea a rea deenaa araea aaa a aaae 30 Remote display application c ccccccceceeeeeeeeeeeceneeeeeeeeeeeeeeseeseceaaaecaeeeeeeeeeeeeeeeeeeenaees 31 Ghapter 4 Menus asiain a aai aaa a aaa eaaa ae dilata aa ai dede 32 Accessing he Menus cia da A R TAR 32 Men ann nciatorS 00 ta II aS ee aa ake 32 Exiting ihe MENUS A TE oh eee cite 33 USER JevelmMmen S sne o aiaa eiia aa aa E aae aaa EE 33 UE aa nO EE E A E EE NE E EE E tan ca ctcaey 34 TIME a aa a a e e o tas he fed fet 34 Date ah estas ete iia eas 35 SCD 2 OO 36 A e rere ener caer ieee elena id dl ey ey 36 FADOUBIMIOI VU seer ech och e de oP td es dede o ea et 37 110 0 presenter acre 37 A RN 38 A e ita loam dedo do id 38 O a NN 38 Er dd ido ia 39 A RN 40 AUN e ala aos ere 41 CAU e e a ale 41 AL 8 ea cr E N 42 Chapter 5 Communications a a r a Daaa eee eee te eee a a D a a a Ea a a a a aa R FaR 43 Detaultipnint formats a e Ed a aaea ri a a aa 43 Chapter 6 Error messages cece eee eee teeter te
31. eeeeeeseesecseccuesaeeeeeeeeees 20 SELECT key default FUNCtiON renr e aaa nina 20 Special Key TUNCIONS ici rat ica filds 20 Accumulator operation s 22 88 beeen iat i eee eit ately 20 Counting application A as 21 SELECT key default function aineenaan arae E cnn andenes 21 Special Key FUNCTIONS oerion m aT E er nr enanas 21 Sample Operation tii is eet zag rinda ytd nausea ade 21 Dribble Sampling ire 21 BUR SAMPING visita atico 22 Piece WEIGH en ia di ida 23 Checkweighing application seresa sn iei N nor cnn narran E 24 SELECT key default MOCION rri o r TAEAE A IEE RAEE 24 SPEClal Koy TUNCIONS eree aiaei eo talla 24 Checkweigh Operation ccccecesecedecesteeccceeeseeeneeeeseneendeqneseenceeeeeesensdeneeneendeseeennanees 24 Weighing a target Object eerie s E E a 25 Setting upper and lower limits ceececececeecceceeeeeeeeeeeeeeeeeeaaeaeeceeeeeeeeeeeeeetenneeaeeas 25 Setpoint operation in the checkweighing application ccccceceeeeeeeeeeeeseeteees 26 ZM303 Indicator User Instructions Batching Application conil 27 SELECT key default function oooonnnccccnnnnacccccnnononnccnnn conan nn cnn conocia nar cnnnn nn n ar rra nnnnrnnnnn 27 Special key fUNCtIONS cooomccccniionccccninnncacccnnn anciana 27 Batching operatio reran Dearie e aer a e a E Se ATEA a a TAEAE E 27 2 Speed TINO cocoa pepi EEA ATAR dd 28 Ingredient Anon tia tit da 28 Independent Setpoint ecceceeececeeccece
32. egments will light Any weight between the lower and upper acceptable weights will cause the middle bargraph segment to light to show the weight is within the target range If the weight is above the upper acceptable weight the right bargraph segments will light 7 Remove the item from the scale and repeat step 6 to check other items 8 To set new upper and lower limits repeat steps 1 through 5 3 4 6 Setpoint operation in the checkweighing application Inside the Gross Zero Band All outputs and annunciators are off Under Target or Below Low Accept Weight SP7 annunciator and Output 1 are on Inside Target SP2 annunciator and Output 2 are on Over Target or Above Upper Accept Weight SP3 annunciator and Output 3 are on a Outputs have to be enabled see Service manual Outputs can be set as latched or unlatched in a password protected menu If outputs are unlatched The annunciators and outputs follow the status of the bargraph except in gross zero band If outputs are latched The annunciators and outputs status is determined by where the first stable weight occurs after an item is placed on the scale The latched annunciator and output is reset OFF only when weight returns inside the gross zero band 26 ZM303 Indicator User Instructions 3 5 Batching application 3 5 Batching application This section applies if your indicator has the Batching application active 3 5 1 SELECT key default functio
33. en tn ttn Anat tE ee eeaaaeeeeeeeaaeeeeeeeaaaeeeseeeaaeeeeseeeseeeeesenaaes 44 Chapter 7 Supervisor Men it 42605 a Ai le eee 45 General Weighing application supervisor MENU 2 0 0 2 e eee eeeeeeeeeeeeeeceeceeeeeeeeeeeeeeeeeeniaaees 46 SOLON o it dr ete tak A A A bn daa diana 47 Annunclators vivo A abe AR ea een Ae si 47 QUIPUES 3100 A dad 47 NpUS min dd REA A a oe breed te 48 Pr A A O A id Ra 48 Reset ince aivtiei ee nie ae eee eee eee eae 49 Mai a o ccUn oe unr rere e Te Trier e 49 Tare Register 1 10 sist cceiediictecedeet a dd dada de bc 49 PORN at A A A 50 O eae eee 50 Battery iia 50 Enable aici natal eatin sei es Rae 1 ad iba aed Mall ee 51 Timeout oes ca ta ii sata cca dame ecg Li A as 51 Accumulator application supervisor MENU 2 ce ceceeeeeeceeceeeeeeeeeeeeeeeteneeccecaeeaeeeeeeeneess 52 Accumulator e e ei to ag cea ete he ee eta i a eal 53 Print totalis iiaei hk A Ad ae ea 53 4 ZM303 Indicator User Instructions Clear total tit A aah ee ie At da 54 O eae eles 54 Reset A ia 54 Counting application supervisor MENU occocccocococoncncnnnnnccnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nan nannnn nr nnnnnn 56 COUNT dd ta E T 57 MOTE enie a a a A Reve eed 57 Print total rerehan eeano ea tel hd oleate 57 Totalformat ina d A ind died adea ai ret 58 Clear totali aaa A alee A needs 58 Checkweighing application supervisor MENU cccccceceeceeeeeeeeeeeeecaeceeeeeeeeeeeeteteeeseneaees 60 CHECK cr Ace eerste cota net e
34. ero rESEt Outputs Latch 8 Unlatch Check y Outputs y Latch amp Unlatch 3 4 5 Press SELECT outPutS is displayed There are two choices for outputs LAtch and unLAtch lf you choose LAtch this means that the weight has to stabilize before the annunciator and output for the appropriate condition Under Accept or Over is activated If you choose unLAtch the annunciator and output will change instantly as the weight changes checkweigh condition In latch mode once activated the annunciator and output will remain unchanged until the item is removed and the gross weight returns to inside the gross zero band From outPutS press SELECT LAtch is displayed Press UNITS to toggle between the choices and when your choice is displayed press ZERO to accept outPutS is displayed Under divisions Check y Outputs gt Under divisions 6 7 ZM303 Indicator User Instructions Press UNITS undrdiv is displayed Use this to set the number of divisions 0 100 below the target weight that is still within the accept window Press SELECT The current value is shown with a flashing right most digit 61 Supervisor menu 62 8 Press ZERO to accept the current value or key in a new value and press ZERO to accept undrdiv is displayed Over divisions Check y Outputs gt Under divisions gt Over divisions 9 Press UNITS oVErdiV is displayed Use this to set the number of divisi
35. ff 3 5 6 Independent setpoints 28 Independent Setpoint works like the general weighing mode setpoints with the addition of start stop controls You can also do negative weight discharge using this mode 1 Press SETUP or press and hold SELECT to access the setpoint editor 2 Set Out1 Out 2 and Out 3 values 3 To start or restart the setpoints press START or F1 4 To stop the process press STOP or F1 F1 toggles the process on and off ZM303 Indicator User Instructions 3 5 Batching application 3 5 7 Fill Discharge Fill Discharge mode is typically used for applications that use negative filling to dispense a smaller amount of product from a large vessel tank or hopper type scale The vessel tank or hopper is filled to a set gross weight and then multiple operations of filling via negative amount of weight into bags or containers can be completed before the vessel tank or hopper requires a recharge or refill Fill Out 1 is assigned as the gross fill amount for the vessel tank or hopper and START or F1 key starts the fill The fill is based only on gross weight If you have Out 1 set to 2000 and the scale already has 500 Ib remaining the Output 1 will cutoff and annunciator SP7 turns off when the additional 1500 is added for a total gross of 2000 Ib Discharge Out 2 is assigned as the discharge fill amount negative weight with the TARE key used to initiate the discharge cycle The scale will tare prior to activat
36. gle between the choices and when your choice is displayed press ZERO to accept diSP is displayed Preact Batch y Type gt Mode gt Display gt Preact 12 Press UNITS PrEAct is displayed This stands for auto preact Preact can be used to compensate for product weight that continues to fill into the bag or container after the setpoint output turns off and before the final weight stabilizes If a preact value is automatically calculated or manually entered the actual cutoff weight will equal the entered setpoint value minus the preact value PrEAct has three choices Manual Auto or cLEAr Each is explained below Manual When Manual preact is not automatically calculated and is only used if the value was entered manually in the SETPNT submenu for PREACT 1 2 and 3 Auto When set to Auto preact is automatically calculated The amount of compensation is calculated based on the average variance between the entered setpoint value and the actual fill weights recorded during the most recent batch cycles Auto Preact is only available in certain Batch Types as noted in their descriptions Calculated Preact values can be viewed in the SETPNT submenu for PREACT 1 2 and 3 cLEAr When cLEAr is selected the current preact values will be set to 0 If PrEAct was set to Auto a new set of compensation values will be calculated on continuing batches If preact was set to oFF then preact will be disabled or new values can be manuall
37. he reset or press UNITS YES is displayed Press ZERO to reset the settings to factory defaults rESEt is displayed Press TARE SEtPnt is displayed If Preset Tare is not enabled skip to step 7 If it is enabled continue to the next step Press UNITS tArE is displayed Use this to O set values for up to 10 preset tares O print the values of the preset tares O reset all preset tares to factory defaults of 0 The following steps describe the procedures Tare Register 1 10 Tare y Edit y Tare 1 10 2 Press SELECT Edit is displayed Press SELECT tArE 1 is displayed This is the first of the 10 preset tare values you can set Press SELECT The current value is displayed with a flashing right digit Press ZERO to accept the displayed value or key in a new value and press ZERO to accept tArE 1 is displayed ZM303 Indicator User Instructions 49 Supervisor menu 6 Press UNITS tArE 2 is displayed 7 Repeat steps 4 through 6 for tArE 2 through tArE 10 Press TARE when finished Edit is displayed Printing Tare y Edit gt Print 8 Press UNITS Print is displayed Use this to print the preset tare values 9 Press SELECT Port 1 is displayed 10 Press F1 to abort the print process or press UNITS to scroll to the desired port and press ZERO to print the information Print is displayed after either action Reset Tare y Edit gt Print gt Reset 11 12 13
38. ing Output 2 SP2 annunciator will light An operator can perform multiple discharge operations When the vessel gross weight is low perform a refill f Press SETUP or press and hold SELECT to access the setpoint editor 2 Set Out1 to the gross fill weight in the vessel or container Set Out 2 to the weight of the product to be discharged into smaller bags or containers To start or restart the large vessel fill process press START or F1 To stop the large vessel filling process press STOP or F1 Press TARE to start the bag filling process OX OV Ss a To stop bag filling process press STOP or TARE ZM303 Indicator User Instructions 29 Indicator applications 3 6 Peak hold application This section applies if your indicator has the Peak Hold application active 3 6 1 SELECT key default function In the Peak Hold application you can view the gross max and min display values by repeatedly pressing SELECT 3 6 2 Special key functions The following key has an extra function in this application F1 F1 resets the min and max peak weights to the current gross weight 3 6 3 Peak hold operation Only the highest weight applied to the scale is displayed when the peak weight value is selected to be displayed Minimum weight is designated by a pair of green circle annunciators Maximum weight is designated by a different pair of green circle annunciators See Figure 3 3 These two These two annunciators light annuncia
39. is means you are in a list Scroll through the choices with the PRINT and UNITS keys and press ZERO to accept 32 ZM303 Indicator User Instructions 4 3 Exiting the menus 4 3 Exiting the menus 1 If you are at the bottom item in a menu use ZERO to accept a choice or value and move up a level or use F1 to escape and move up one level without accepting the choice or value From that point press TARE repeatedly until SAVE no is displayed This means Do not save changes 2 Press UNITS to scroll through the choices SAVE no SAVEYES and CAnCEL Press ZERO to accept the displayed choice If you choose SAVE no or SAVEYES the indicator exits the menu and returns to normal weighing mode OR If you choose CANCEL the indicator remains in the menu 4 4 USER level menus The USER level menus are available to the user The other menu levels are for supervisors and technicians only The USER level password 111 contains the User About and Audit menus arranged as shown in Figure 4 1 Normal SELECT Y Weighing Mode TARE A Press and PRINT lt hold F1 key UNITS p gt ZERO __ Enter 111 E 8 press ZERO F1 Escape or A See See See page 34 page 37 page 41 Figure 4 1 USER level password 111 menus ZM303 Indicator User Instructions 33 Menus 4 5 User menu The User menu is shown in Figure 4 2 Enter View Site ID Seal Status SELECT Y TARE A PRINT lt UNITS ZERO __1 F1 Esca
40. ix UK Foundry Lane Smethwick West Midlands England B66 2LP Tel 44 0 8453 66 77 88 Fax 44 0 121 224 8183 Email info awtxglobal com www averyweigh tronix com
41. k sampling In this sampling method you place the specified number of items on the scale all at once in bulk and the scale automatically starts to calculate piece weight and then shows the count This is the default sampling method Each method is described below 3 3 4 Dribble sampling With the dribble sampling method active follow these steps to count 1 Press ZERO to zero the scale if necessary Za Use a tare method to tare a container if necessary SeeNet weighing on page 16 3 Press SAMPLE or F1 ZEroing is briefly displayed This means the indicator is zeroing itself A numeric value XX is then displayed This is the current sample size 4a Accept the current sample size by pressing ZERO OR ZM303 Indicator User Instructions 21 Indicator applications Ab Enter a new sample size and press ZERO Add is displayed Count the number of sample items onto the scale and when ready press SAMPLE or F1 buSY is briefly displayed followed by one of two possible outcomes a Ifthe sample met the minimum sample requirements and the weight is stable the display will show the correct number of parts on the scale and COUNT is lit b Ifthe sample size was not large enough or if the weight was unstable Abort is briefly displayed and the display returns to gross weighing mode Repeat steps 3 through 5 using a larger sample size py SSS Minimum sample weight is the gross zero band value The initial sample cou
42. l light The UNDER and OVER bargraph segments are fixed at 1 division each 4 Remove the object and replace with the next object to be checked The bargraph will show if the weight is under over or within the target weight range If the weight is under SP7 annunciator and the UNDER bar segments will light If the weight is over SP3 annunciator and the OVER bar segments will light 5 Repeat step 4 until you are finished weighing items The current target weight will be active until you repeat steps 1 through 3 with a new item of a different weight 3 4 5 Setting upper and lower limits With the indicator in checkweighing mode follow these steps to set a target by setting upper and lower limits 1 Press ZERO to zero the scale if necessary 2 Enter a tare if necessary Refer to Net weighing on page 16 for instructions 3 With weight inside the gross zero band press TARGET Lo will be displayed briefly and then the current value for the lower accept weight 4 Press ZERO to accept this or key in a new lower accept weight and press ZERO Hi is briefly displayed and then the current value for the upper accept weight 5 Press ZERO to accept this or key in a new upper accept weight and press ZERO The display returns to normal weighing mode ZM303 Indicator User Instructions 25 Indicator applications 6 Place a weight on the scale If the weight is below the lower accept weight the left bargraph s
43. ll be calculated for each ingredient to adjust the cutoff weight accordingly If NEG FILL is set to YES it will only operate for a single ingredient with OUT 1 used for discharge filling based on negative weight Independent Setpoints Out 1 2 and 3 values operate the Outputs independently Press F1 or START for initial start If MODE is set to AUTO this will allow the outputs to activate automatically using the gross zero band as an interlock for Auto Start If MODE is set to MANUAL this will require pressing the F1 or START key to activate the outputs The outputs will remain deactivated after the last Out X weight has been reached A value of 0 disables the independent output If DISP is set to NET this uses net weight and if DISP is set to GROSS this uses gross weight for cutoff value PREACT setting does not apply to INDEPENDENT If NEG FILL is set to YES this allows operation of Out 1 2 and 3 values in negative weight mode Fill Discharge MODE setting does not apply to Fill Discharge DISP setting does not apply to Fill Discharge If PREACT is set to AUTO it only applies during the Out 2 discharge cycle NEG FILL setting does not apply to Fill Discharge ZM303 Indicator User Instructions 67 Supervisor menu 7 6 Peak Hold application supervisor menu Figure 7 6 shows the Supervisor menu when you are in the Peak Hold application SELECT Y eek PRINT lt 4 UNITS gt No Off 1 3600 ZERO __1 min
44. n Reset Accum y Print Total gt Total Format gt Clear Total gt Print gt Reset 15 Press UNITS rESEt is displayed Use this to reset the all the items under AccuM to the factory defaults 16 Press SELECT no is displayed 17 Press ZERO to abort the reset or press UNITS YES is displayed ZM303 Indicator User Instructions 18 19 20 21 7 2 Accumulator application supervisor menu Press ZERO to reset the settings to factory defaults rESEt is displayed Press TARE Accum is displayed Press UNITS bAttErY is displayed The battery menu is identical in all the applications Refer to step 1 on page 50 for information on setting up the battery This completes the Supervisor menu for the Accumulation application Repeatedly press TARE until the indicator returns to normal weighing mode The current weight value is displayed ZM303 Indicator User Instructions 55 Supervisor menu 7 3 Counting application supervisor menu Figure 7 3 shows the Supervisor menu when you are in the Counting application Appears only if Preset SELECT Y Tare is enabled TARE A AOTC s PRINT lt Setpat Hi Tare ieee a F1 Escape or A 1 3600 minutes or Enter Print format for Total operation Edit Print Reset Edit H Print Reset No Tare 1 Tare 10 Bold boxes and text denote defaults No Key Key Key XL in In in value value value None Print stop H D HE Setup H
45. n In the Batching application you can view the gross net and tare display values by repeatedly pressing SELECT 3 5 2 Special key functions all The following keys have an extra function in this application START Press START to start a batch operation STOP Press STOP to stop a batch operation F1 F1 acts as a START and a STOP key on successive presses The Batch application has added selections for Preact values 1 3 in the Setpoint menu shown below Press SETUP Key in Key in Key in Key in Key in Key in setpoint setpoint setpoint preact preact preact value value value value value value 3 5 3 Batching operation Batching allows the indicator to control up to three motors timers augers gates etc using the three outputs for the purpose of making batches based on weight There are four types of batching operation O 2 speed single ingredient e Ingredient filling up to three ingredients e Independent setpoints filling e Fill discharge operation Other parameters that are set in a password protected menu affect the batching operation The bargraph will sequentially light up to show from 0 to 100 of the batch weight in all types of batching except the independent setpoints ZM303 Indicator User Instructions 27 Indicator applications 3 5 4 2 Speed filling El 2 Speed is for a single ingredient with a dual speed filling control Fast Slow typically a valve or hopper gate that
46. n supervisor menu on page 68 Remote Display application supervisor menu on page 70 ZM303 Indicator User Instructions 45 Supervisor menu 7 1 General Weighing application supervisor menu Figure 7 1 shows the Supervisor menu when you are in the General Weighing application Appears only if Preset Tare is enabled Y Bold boxes and text Tare denote defaults SELECT Y OFF 1 3600 minutes TARE A PRINT lt q Edit Print Reset Edit H Print Reset rs gt Port 1 No Yes ZERO Tare 1 J Tare 10 F1 Escape or A Port 1 No Key kay ra S77 in in value value value None Print sto H D H Setup H Under H Over H Assu H User Figure 7 1 Supervisor menu for the General Weighing application E The Setpoint menu is the same for all the applications so will only be explained once here Exceptions are noted in the text Follow these steps to set the items in the Supervisor menu 46 ZM303 Indicator User Instructions 7 1 General Weighing application supervisor menu 7 1 1 Setpoint Supery Setpoint Super y Setpoint shown above illustrates that you move down from SuPEr to CO lt The y and gt symbols used in this section stand for direction moved in the menu So SEtPnt This will help you keep track of where you are in the menu structure 1 With the General Weighing application active access the Supervisor menu Refer to Accessing the menus on page 32 for instructions
47. nt is 5 pieces The maximum number of pieces that can be sampled is 9999 Place the parts on the scale to be counted To accumulate the count and number of transactions press PRINT while in count mode If enabled press and hold PRINT for three seconds to print and or clear the active count total These functions are enabled or disabled in a password protected menu 3 3 5 Bulk sampling With the counting application and the bulk sampling method active follow these steps to count 1 2 4a OR Ab 22 Press ZERO to zero the scale if necessary Use a tare method to tare a container if necessary SeeNet weighing on page 16 Press SAMPLE or F1 ZEroing is briefly displayed This shows the indicator is Zeroing itself A numeric value XX is then displayed This is the current sample size Accept the current sample size by pressing ZERO Enter a new sample size and press ZERO Add is then displayed Place the correct number of samples on the scale all at the same time buSY is briefly displayed followed by one of two possible outcomes a Ifthe sample met the minimum sample requirements and the weight is stable the display will show the correct number of parts on the scale and COUNT is lit ZM303 Indicator User Instructions 3 3 Counting application b Ifthe sample size was not large enough or if the weight was unstable Abort is displayed and the display returns to gross weighing mode Repeat steps 3
48. ons 0 100 above the target weight that is still within the accept window 10 Press SELECT The current value is shown with a flashing right most digit 11 Press ZERO to accept the current value or key in a new value and press ZERO to accept oVErdiV is displayed Reset Check y Outputs gt Under divisions gt Over divisions gt Reset 12 Press UNITS rESEt is displayed Use this to reset the all the checkweigher variables to the factory defaults 13 Press SELECT no is displayed 14 Press ZERO to abort the reset or press UNITS YES is displayed 15 Press ZERO to reset the settings to factory defaults rESEt is displayed 16 Press TARE chEcK is displayed 17 Press UNITS bAttErY is displayed The battery menu is identical in all the applications Refer to step 1 on page 50 for information on setting up the battery 18 This completes the Supervisor menu for the Checkweighing application Repeatedly press TARE until the indicator returns to normal weighing mode The current weight value is displayed ZM303 Indicator User Instructions 7 5 Batching application supervisor menu 7 5 Batching application supervisor menu Figure 7 5 shows the Supervisor menu when you are in the Batching application Appears only if Preset Tare is enabled Bold boxes and text a eae denote defaults L i Off 1 3600 minutes of Tare 1 Tare 10 G Print Net
49. pecifications Avery Weigh Tronix D START ID SAMPLE Figure 2 1 Front panel of the ZM303 indicator display A ABABA COUNT PRINT HEN oe as as o O 0 8 o QTY Figure 2 2 Outdoor display example The ZM303 can connect to USB flash drives printers remote displays computers and other peripheral devices via USB ethernet and serial connections ZM303 Indicator User Instructions 11 Introduction 2 1 Front panel The front panel shown in Figure 2 1 consists of the keys and display E gt Never press a key with anything but your finger Damage to the overlay may result f sharp or rough objects are used The normal function of the keys on the front panel are listed below Some keys will have special functions in certain applications Details are provided in the individual application sections Also prompts for a keyboard tare if enabled Acts as an up arrow key for menu navigation Allows you to access minus and comma signs Press the SELECT key to toggle between the active display values Press and hold to enter the setpoint editor Acts as a down arrow key for menu navigation Allows you to access minus and comma signs Press the PRINT to send information to a peripheral device through a configured communications port Performs accumulator function if enabled Acts as a left arrow key for menu navigation Press the UNITS key to scroll through the available units of measur
50. peor A Figure 4 2 User menu Use this menu to set the time and date to enter a site ID and view the physical seal status Each is explained below 4 5 1 Time User y Time AG i ae pe ee Gee a a a GA The y and gt symbols used in this section stand for direction moved in the menu So User y Time shown above illustrates that you move down from uSEr to tiME This will help you keep track of where you are in the menu structure 1 Access the User menu see Accessing the menus on page 32 and press SELECT tiME is displayed Use this to set the time and clock style 2 Press SELECT SEt is displayed 3 Press SELECT h xis displayed with the x flashing This is a numeric entry screen for the hour value 34 ZM303 Indicator User Instructions 4 5 2 Date User y Time gt Date ZM303 Indicator User Instructions 4 5 User menu Key in the hour of the day using military 24 hr time and press ZERO to accept M xis displayed with the x flashing This is a numeric entry screen for the minute value Key in the minute value and press ZERO to accept S xis displayed with the x flashing This is a numeric entry screen for the second value Key in the seconds value and press ZERO to accept SEt is displayed Press UNITS StYLE is displayed Use this to set the style of clock for printouts Choices are 12hr 12hr AP AM PM and 24hr military time Press SELECT 12hr is displayed P
51. r menu 1 With the Accumulator application active access the Supervisor menu using password 1793 Refer to Accessing the menus on page 32 for instructions From SuPEr press SELECT SEtPnt is displayed 2 Press UNITS until AccuM is displayed Use this to set the items relating to accumulation Under AccuM you can do the following Enable Disable the ability to print the accumulated total Prt tot Key in a print format number for printing the total accumulated weight information tot FMt Enable Disable the ability to clear the total accumulation information when the total is printed clr tof Print the accumulation report for all 10 memory channels Print Reset all 10 accumulator memory channel values to 0 rESEt The following steps describe the procedure to set these items Print total Accum y Print Total 3 From AccuM press SELECT Prt tot is displayed This stands for print total 4 Press SELECT OFF is displayed 5 Press ZERO to keep the print total function disabled or press UNITS to toggle to on and press ZERO to enable printing of the accumulated total Prt tot is displayed If enabled during normal operation the user can press and hold PRINT for three seconds and the selected total print format see step 8 below will be sent out any port that is set up to printed The display will flash Prn tot Total format Accum y Print Total gt Total Format 6 Press UNITS tot
52. re labeled as shown by the 1 1 and 1 1 1 headings The names of the chapter and the next subsection level appear at the top of alternating pages of the manual to remind you of where you are in the manual The manual name and page numbers appear at the bottom of the pages 1 1 1 Text conventions Key names are shown in bold and reflect the case of the key being described If a key has a dual function it may be referred to by its alternate function Displayed messages appear in bold italic type and reflect the case of the displayed message Annunciator names appear as italic text and reflect the case of the annunciator 1 1 2 Special messages Examples of special messages you will see in this manual are defined below The signal words have specific meanings to alert you to additional information or the relative level of hazard CAUTION This is a Caution symbol Cautions give information about procedures that if not observed could result in damage to equipment or corruption to and loss of data NOTE This is a Note symbol Notes give additional and important information hints and tips that help you to use your product 1 2 Installation all NO USER SERVICEABLE PARTS REFER TO QUALIFIED SERVICE PERSONNEL FOR SERVICE ZM303 Indicator User Instructions 7 General information and warnings 1 2 1 Safe handling of equipment with batteries CAUTION Danger of explosion if battery is incorrectly replaced
53. ress UNITS to scroll through the choices Press ZERO to accept the displayed choice StYLE is displayed Press TARE tiME is displayed From tiME press UNITS dAtE is displayed Press SELECT SEt is displayed Press SELECT y xis displayed with the x flashing This is a numeric entry screen for the year value Key in the year and press ZERO to accept M xis displayed with the x flashing This is a numeric entry screen for the month Key in the month value and press ZERO to accept d xis displayed with the x flashing This is a numeric entry screen for the day value Key in the day value and press ZERO to accept SEt is displayed 35 Menus 10 4 5 3 Site ID Press UNITS StYLE is displayed Use this to set the style of date for printouts Choices are MMDD2Y MMDD4Y DDMM2Y and DDMMA4Y Press SELECT MMDD2Y is displayed Press UNITS to scroll through the choices Press ZERO when your choice is displayed The choice is made and StYLE is displayed Press TARE dAtE is displayed User y Time gt Date gt Site ID 1 4 5 4 Seal From dAtE press UNITS SitE id is displayed Press SELECT A numeric entry screen is displayed Key in a site ID number on the numeric keypad and press ZERO to accept SitE id is displayed User y Time gt Date gt Site ID gt Seal 1 36 From SitE id press UNITS SEAL is displayed Press SELECT
54. ring use of the indicator Message Display Overload Can t fit on display Underload Entry not in valid range Password entry failed Remote display not receiving data from the master indicator Indicator did not reach a stable zero weight within time window set for automated weighing process 44 ZM303 Indicator User Instructions 7 Supervisor menu This menu allows a supervisor to change those functions of an application that are configurable Access the supervisor menu using the password 1793 Refer to Accessing the menus on page 32 for instructions EY q Wherever there is an option to print information in the any of the supervisor s menus the information will print out of Port 1 Port 2 or to USB whichever is configured VE ee F EF The menus are always explained in a sequential manner to cover all information in a logical fashion You will probably never access all the menu items in this manner You can navigate to the area of the menu that needs to be changed by using the navigation key chart shown with each menu The Supervisor menu changes based on the active application Go to the appropriate section General Weighing application supervisor menu on page 46 Accumulator application supervisor menu on page 52 Counting application supervisor menu on page 56 Checkweighing application supervisor menu on page 60 Batching application supervisor menu on page 63 Peak Hold applicatio
55. s ZERO to accept the existing setting or key in a new format number and press ZERO tot FMt is displayed Clear total Count y Mode gt Print Total gt Total Format gt Clear Total 12 13 14 15 16 58 Press UNITS cLr tot is displayed This stands for clear total Choose YES to enable clearing the count total when printed Choose no to disable this function If enabled the total is cleared if the user presses and holds the PRINT key for three seconds The message cLr tot will flash The total is printed prior to clearing if this was enabled in step 8 above Press SELECT The current setting is displayed Press UNITS to toggle between the choices and when your choice is displayed press ZERO to accept cLr tot is displayed Press TARE count is displayed Press UNITS bAttErY is displayed The battery menu is identical in all the applications Refer to step 1 on page 50 for information on setting up the battery ZM303 Indicator User Instructions 7 3 Counting application supervisor menu 17 This completes the Supervisor menu for the Counting application Repeatedly press TARE until the indicator returns to normal weighing mode The current weight value is displayed ZM303 Indicator User Instructions 59 Supervisor menu 7 4 Checkweighing application supervisor menu Figure 7 4 shows the Supervisor menu when you are in the Checkweighing application Appears only if Preset Bol
56. specified number of items on the scale all at once in bulk and the scale automatically starts to calculate piece weight when the weight stabilizes The count is then displayed Dribble In dribble sampling method you count out the specified number of items onto the scale and when you are ready press the SAMPLE key and the scale calculates piece weight and then shows the count 4 With ModE displayed press SELECT buLK is displayed 5 Press UNITS to toggle between the choices and when your choice is displayed press ZERO to accept ModE is displayed Print total Count y Mode gt Print Total 6 Press UNITS Prt tot is displayed This stands for print total 7 Press SELECT no is displayed ZM303 Indicator User Instructions 57 Supervisor menu 8 Press ZERO to keep the print total function disabled or press UNITS to toggle to YES and press ZERO to enable printing of the count total Prt tot is displayed If enabled during normal operation the user can press and hold PRINT for three seconds and the selected total print format see step below will be sent out any port that is set up to printed The display will flash Prn tot Total format Count y Mode gt Print Total gt Total Format 9 Press UNITS tot FMt is displayed This stands for the total print format 10 Press SELECT The current print format number is displayed with a flashing right most digit Default is format 8 11 Pres
57. t format will be output through the configured port to the connected peripheral device The indicator can be configured to only allow one print for each weighing sequence If PRINT is pressed when so configured the message cAnt will appear Refer to Default print formats on page 43 ZM303 Indicator User Instructions 19 Indicator applications 3 2 Accumulator application This section applies if the Accumulator application is active 3 2 1 SELECT key default function In the Accumulator application you can view the Gross Net Tare Gross Total Net Total and Transaction Count display values by repeatedly pressing SELECT 3 2 2 Special key functions The following key has an extra function in this application F1 Press F1 and the active accumulator channel chAn X appears Scroll through the list of channels chAn 1 chAn 10 using PRINT or UNITS Press ZERO to activate that channel 3 2 3 Accumulator operation The accumulator application can be used to record totals of individual weighments Follow these steps 1 Press ZERO to zero the scale if necessary 0 is displayed 2 Place item on the scale Weight is displayed gross and net totals You have 10 accumulator channels that can be used to store CCO Ro You can use gross or net weighing with the accumulator application as it stores both totals for up to 10 separate products 3 Press PRINT to add weight to the accumulator and to print the selected print
58. the menus in the ZM303 1 With the indicator powered up and in normal operating mode press and hold F1 Pass is displayed prompting you to enter the password 2 Key in the password for the menu you want and press the ZERO key The first item in the top level of the menu you accessed is displayed 3 Use the navigation keys shown below to navigate through the menu structure The symbols in the chart appear on the bottom of the keys Press SELECT W to move down in a menu Press TARE A to move up in a menu except at the bottom item in a menu then use ZERO 1 or F1 Press PRINT Gto move left in a menu Press UNITS gt to move right in a menu Press ZERO ___ _ to accept a value or choice and move up in the menu Press F1 to escape and move up in the menu 4 2 Menu annunciators The menu structure is made up of menu items parameters value entry screens and lists from which you choose one item To help you know where you are in the menu the bargraph at the top of the display is on while the indicator is in the menus and will change appearance according to the following rules All segments flashing This means you are in the menu structure but not in any of the following screens Center flashing others solid This means you are in a parameter prompt screen Center flashing others off This means you are in a numeric entry screen Enter a number and press ZERO to accept Right flashing others off Th
59. through 5 using a larger sample size EE Minimum sample weight is the gross zero band value The initial sample count is 5 pieces The maximum number of pieces that can be sampled is 9999 6 Place the parts on the scale to be counted To accumulate the count and number of transactions press PRINT while in count mode 7 If enabled press and hold PRINT for three seconds to print and or clear the active count total These functions are enabled or disabled in a password protected menu 3 3 6 Piece weight entry Piece weight can be entered manually 1 Press and hold SAMPLE The current piece weight is displayed 2 Key in a new value and press ZERO to accept ZM303 Indicator User Instructions 23 Indicator applications 3 4 Checkweighing application This section applies if your indicator has the Checkweighing application enabled 3 4 1 SELECT key default function In the Checkweighing application you can view the gross net and tare display values by repeatedly pressing SELECT 3 4 2 Special key functions The following keys have an extra function in this application TARGET Press TARGET to set the target weight or upper and lower limits as described below F1 F1 works the same as the TARGET key when pressed 3 4 3 Checkweigh operation Checkweighing allows a quick visual check of the acceptability or unacceptability of an item s weight Figure 3 2 shows the checkweighing bargraph at the top of the display
60. tors light for minimum weight for maximum weight Figure 3 3 Min Max annunciators With the Peak application active follow these steps to perform and view peak weighments 1 Repeatedly press SELECT until the two green circle annunciators on the right light up See Figure 3 3 This means you are now viewing the peak or maximum weight 2 With no weight on the scale press ZERO if necessary press F1 to reset any previous peak value on the display 3 Place weight on the scale and then remove it The display will show the peak weight recorded during the weighment 4 To reset the peak press F1 The minimum and maximums are reset to the current gross weight 30 ZM303 Indicator User Instructions 3 7 Remote display application 5 Repeat the steps to perform another peak weighment Below is an example of the minimum weight display Note the pair of circle annunciators that are lit Below is an example of the maximum weight display Note that a different pair of circle annunciators are now lit 3 7 Remote display application This section applies if you have the Remote Display application active The indicator can be configured to work as a remote display with other compatible indicators or the GSE 350 3551S ZM303 Indicator User Instructions 31 Menus 4 Menus Password protected menus are available to configure the indicator and or view information 4 1 Accessing the menus Follow these steps to access
61. tructions 1 4 Cleaning the machine 1 4 Cleaning the machine Table 1 1 Cleaning DOs and DON Ts Wipe down the outside of standard products Attempt to clean the inside of the machine with a clean cloth moistened with water and Use harsh abrasives solvents scouring cleaners or a small amount of mild detergent alkaline cleaning solutions Spray the cloth when using a proprietary Spray any liquid directly on to the display windows Cleaning fluid 1 5 Training Do not attempt to operate or complete any procedure on a machine unless you have received the appropriate training or read the instruction books To avoid the risk of RSI Repetitive Strain Injury place the machine on a surface which is ergonomically satisfactory to the user Take frequent breaks during prolonged usage 1 6 Sharp objects Do not use sharp objects such as screwdrivers or long fingernails to operate the keys 1 7 FCC and EMC declarations of compliance United States This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communic
62. utes F1 Escape or A Bold boxes and text No das i in in in value value value None Print stop H D H Setup H Under H Over H Accu H User Figure 7 6 Supervisor menu for the Peak Hold application General Weighing application supervisor menu on page 46 Go there for information SOCK ar The Setpnt and bAttErY submenus in Figure 7 5 are the same as described in on those submenus The unique submenus to this application are described below 7 6 1 Peak hold Super y Setpoint gt P hold 1 With the Peak Hold application active access the Supervisor menu using password 1793 Refer to Accessing the menus on page 32 for instructions From SuPEr press SELECT SEtPnt is displayed 2 Press UNITS twice P hoLd is displayed Use this to reset the min max peak If the F1 key is disabled which is the normal key to reset min max the supervisor needs an alternate method to reset these values 68 ZM303 Indicator User Instructions 7 6 Peak Hold application supervisor menu Reset P hold y Reset 3 Press SELECT rESEt is displayed 4 Press SELECT no is displayed 5 Press UNITS to toggle between the no and YES choices Press ZERO to accept The min max are reset and rESEt is displayed 6 Press TARE repeatedly to return to normal weighing operation ZM303 Indicator User Instructions 69 Supervisor menu 7 7 Remote Display application supervisor menu Figure 7 7 shows the Supervisor menu when
63. y entered in the setpoint menu 13 Press SELECT The current setting is displayed ZM303 Indicator User Instructions 65 Supervisor menu 14 Press UNITS to scroll through the choices and when your choice is displayed press ZERO to accept PrEAct is displayed Negative fill 15 16 17 18 19 20 Batch y Type gt Mode gt Display gt Preact gt Negative Fill Press UNITS NEG FIL is displayed This stands for negative fill This has two choices OFF or on Each is explained below Choose oFF to disable negative fill default Choose on to enable negative fill Operation varies depending on Type chosen See Notes on batching on page 66 Press SELECT The current setting is displayed Press UNITS to scroll through the choices and when your choice is displayed press ZERO to accept NEG FIL is displayed Press TARE bAtch is displayed Press UNITS bAttErY is displayed The battery menu is identical in all the applications Refer to step 1 on page 50 for information on setting up the battery This completes the Supervisor menu for the Batching application Repeatedly press TARE until the indicator returns to normal weighing mode The current weight value is displayed 7 5 2 Notes on batching 66 2 Speed MODE setting does not apply to 2 SPEED If DISP is set to NET an autotare will occur prior to the start of the fill If DISP is set to GROSS no autotare will
64. you are in the Remote Display application SELECT Y Setpnt R disp Battery TARE A PRINT lt Enabl T t fe Off 1 3600 ZERO _ minutes F1 E om Bold boxes and text denote defaults No Yes Key Key Key NL in in in value value value None Print stos H D H Setup H Under H over H Accu H User Figure 7 7 Supervisor menu for the Remote Display application General Weighing application supervisor menu on page 46 Go there for information ECG all The Setpnt and bAttErY submenus in Figure 7 7 are the same as described in on those submenus The unique submenu to this application is described below 1 With r diSP displayed press SELECT ModE is displayed 2 Press SELECT rd or 350iS is displayed Choose which type of remote display will be connected to the indicator 3 Press UNITS to toggle between the choices and press ZERO to accept ModE is displayed 4 This completes the Supervisor menu for the Remote Display application Repeatedly press TARE until the indicator returns to normal weighing mode The current weight value is displayed When set as a remote display the indicator will only function as a remote display for the connected master indicator 70 ZM303 Indicator User Instructions Avery Weigh Tronix ea Avery Weigh Tronix USA 1000 Armstrong Dr Fairmont MN 56031 USA Tel 507 238 4461 Fax 507 238 4195 Email usinfo awtxglobal com www wtxweb com Avery Weigh Tron

ZM303 User`s Manual - Avery Weigh

Contents

Download Pdf Manuals

Related Search

Related Contents