PB300E Series Instructions
Contents
1. NTERMATIC INSTALLATION PBSOOE SERIES OPERATION amp TIME CONTROLS SERVICE MANUAL 24 Hr Electronic Timer Replacement Upgrade Kits Model PB313EK Clock Supply Voltage 120 V 50 60 HZ Model PB314EK Clock Supply Voltage 240 V 50 60 HZ GENERAL INFORMATION The PB300EK Series Electronic Timers are made to fit and replace most PB series Intermatic and certain other brand mechanical or electronic timers The connected load however must not exceed the rating of this timer The timer is completely enclosed and a replaceable lithium battery will hold up memory for up to three years The kit contains all the necessary hardware for a speedy repair or exchange SPECIFICATIONS MYLAR INSULATOR Rating PROTECTING BATTERY 16A Resistive 8A FLA 2 362 i CONTACTS REMOVE Contact Configuration 2 125 i 374 s 079 BEFORE INSTALLATION Single Pole Double Pole 5 y G Power Consumption C P 8V A L INDEPENDENT Battery Type CLOCK SUPPLY CR2032 1 5V Lithium Battery Life NC 3 Years Minimum i 2 No of Programming Periods Ql ia Oy ll PIF o 8 On 8 Off ren a Minimum Interval 250 MALE QUICK CONNECT 1 minute TERMINALS INSTALLATION CAUTION e Prior to installation disconnect electricity at main panel2. TY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES ALL IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE This warranty service is available by either a returning the product to the dealer from whom the unit was purchased or b mailing postage prepaid to the nearest authorized service center listed Please be sure to wrap the product securely when mailing to avoid shipping damage This warranty is made by Intermatic Incorporated After Sales Service 7777 Winn Rd Spring Grove IL 60081 9698 815 675 7000 http www intermatic com Because of our commitment to continuing research and improvements Intermatic Incorporated reserves the right to make changes without notice in the specifications and material contained herein and shall not be responsible for any damages direct or consequential caused by reliance on the material presented INTERMATIC INCORPORATED SPRING GROVE IL 60081 9696 158PB12524 http www intermatic com
3. e Make sure the clock supply voltage of the timer slated for replacement is the same as this timer e Make sure the intended load is within the capacity of this timer see specifications above 1 Both the old and the new timers have two sets of terminals LOAD and CLOCK SUPPLY Identify and mark the leads connected to these terminals 2A Old Timer with four 1 4 inch tabs Remove female terminals from tabs and remove timer Install new timer using the screws and nuts supplied Reconnect the two clock supply leads to CLOCK SUPPLY terminals and either one of the load leads to terminal C and the other load lead to N O normally open terminal 2B Old Timer with two CLOCK SUPPLY LEADS and two 1 4 inch LOAD tabs Disconnect leads at twist on wire connectors and remove female terminals from tabs Remove timer Install new timer using the screws and nuts sup plied Connect the stripped ends of either leads supplied to either wire nutted junctions Connect either one of the load leads to terminal C and the other load lead to N O normally open terminal 2C For other than Intermatic made timers timers with 5 tabs and or permanently attached leads identify first each lead or tab then follow 2A or 2B above and corresponding markings on back of new timer SETTING OPERATING INSTRUCTIONS Programming Instructions To Set or Change the Time of Day To clear entire memory press key Hold down the CLOCK key while pressing either the HOUR or MINUTE
4. is repositioned above the word AUTO TROUBLESHOOTING Symptom Blank Display Timer will not respond Memory is full Possible Cause s Discharged battery Defective timer Corrective Action P E dota Replace battery A EA T ATT Replace timer EPE EE Press to clear memory to programming Timer will not function Timer is in the wrong saab sep AEE TE Press SELECT key and move as programmed SELECT mode indicator bar over to AUTO Timer is ON at all times Timer is in ON mode See above BEE e E Replace timer ONE YEAR LIMITED WARRANTY lf within the warranty period specified this product fails due to a defect in material or workmanship Intermatic Incorporated will repair or replace it at its sole option the unit free of charge This warranty applies only to the original purchaser and is not transferable This warranty does not apply to a damage caused by accident abuse mishandling dropping acts of God or any negligent use b units which have been subject to unauthorized repair opened taken apart or otherwise modified c units not used in accordance with instructions d damages exceeding the cost of the product Some states do not allow a limitation of damages so the foregoing limitation may not apply to you This warranty gives you specific legal rights and you may have other rights that vary from state to state INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES THIS WARRAN
5. keys Continue pressing until the desired number is shown Then simply lift finger off the CLOCK key to set To Set Program ON OFF times Press TIMER key once to enter into program mode Display will show 1 ON Press the HOUR key and then the MINUTE key to select the desired first ON time Press TIMER key once Display will show 1 OFF Repeat previous step to select the desired first OFF time Repeat the entire sequence to complete up to eight total ON OFF times as desired When program ming is done press the CLOCK key then the SELECT key repeatedly until the indicator bar is above the word AUTO To Review Program Press TIMER key repeatedly When done press CLOCK key to return to the time of day To Cancel Change Part of the Program Press TIMER key repeatedly until the particular ON or OFF time appears Set new ON or OFF time See To set Programs To Override the Automatic Operation one time Press OVR KEY YIntermatic SELECT ON AUTO OFF Display Q A Reset port Indicator LED ON when connected to power source and con tacts are closed to cancel all prior settings ON AUTO OFF Select Key Function Keys NOTE Timer will resume automatic operation with the next opposite setpoint To Override Automatic Operation Permanently Press SELECT key to move indicator bar to the desired ON or OFF position Note Timer will not resume automatic operation until indicator bar
Download Pdf Manuals
Related Search