INSTALLATION INSTRUCTIONS
Contents
1. a A o Qj el 52100003E 11 10 Component Installation Connect the 8 pin connector and 1 pin connector of the tow hitch wire har ness to the converter Mount the converter Locate the mounting hole on the lower 2C driver s side rear interior area Next locate the area on the wheel well that the converter will be mounted Clean this area with isopropyl alcohol NOTE Clean the surface with isopropyl alcohol Mix one part isopropyl alcohol to one part of water 2D 52100003E Insert the M8 X 2 16 bolt from the back side place the converter bracket over the bolt and start the nut 8 Do not tighten at this time Locate the correct mounting position then remove the protective tape from the butyl tape on the back of the con verter Place the converter on the mounting area and then tighten the mounting bolt and nut to 13 5 N m 0 39 Kg m 119 in Ib Jo EOM Route the tow hitch wire harness 2 ground lead to the ground bolt located on the passenger side near the rear seat Remove the existing ground bolt and place the eyelet of the ground wire as shown Reinstall the original ground bolt and tighten to 8 N m 0 8 Kg m 71 in Ib Route the driver s side section of the interior wire harness to the driver s side rear tail lamp 4 pin connector Disconnect the driver s side rear tail lamp 4 pin connector NOTE Make sure2. after the interior wire harness is routed the vehicle foam insulator is in its proper location TAIL LAMP WIRE yx HARNESS 52100003E Connect the driver s side vehicle wire harness 4 pin connector a to the tow hitch wire harness 42 4 pin connector b Connect the tow hitch wire 4 pin c and the tail lamp wire harness 4 pin connector d with packing foam tape Route the passenger side tail lamp harness connectors of the tow hitch wire harness to the passenger side tail lamp connectors Disconnect the vehicle tail lamp connectors NOTE Make sure after the interior wire harness is routed the vehicle foam insulator is in its proper location Connect the passenger side vehicle wire harness 4 pin connector a to the tow hitch wire harness 4 pin connector b Connect the tow hitch wire 2 4 pin c and the tail lamp wire harness 4 pin connector d with packing foam tape WIRE HARNESS Remove the tape from the vehicle 1 pin connector 14 52100003E Connect the vehicle 1 pin connector and the tow hitch wire harness con nector 10 Secure the ground lead portion of the tow hitch wire harness 2 using three 3 plastic ties PLASTIC TIES 11 Secure the ground lead portion of the tow hitch wire harness 2 using five 5 plastic ties Driver s side from NS center area going rearward TOES s T 52100003E 12 Secure the
3. driver s side portion of the tow hitch wire harness 2 using two 2 plastic ties 13 Secure the passenger side portion of the tow hitch wire harness using two 2 plastic ties Passenger side tail lamp area Secure the passenger side portion of the tow hitch wire harness 2 using three 3 plastic ties Lower pas senger side below tail lamp area 16 52100003E Secure the rear portion of the tow hitch wire harness 2 using three 3 plastic ties Across the back of the interior Secure the driver s side portion of the tow hitch wire harness 62 using two 2 plastic ties Rear lower area drive side tail lamp area Secure the driver s side portion of the 52100003E tow hitch wire harness 62 using two 2 plastic ties Driver s side tail lamp area 18 Apply packing foam tape 2 over the tow hitch wire harness 2 to secure it to the body NOTE Clean the surface with isopropyl alcohol Mix one part isopropyl alcohol to one part of water 18 52100003E 11 Installation Underside of the Vehicle Route the exterior harness 0 along the driver s side of the hitch member and secure it using the two 2 retain er clips Install the flat 4 pin connector on the tow hitch member using two 2 bolts M5 X 2 16 and nuts 5 Torque to 3 9 N m 0 39 Kg m 35 Route the exterior h
4. hinge bolts that secure the spare SPARE TIRE COVER HES Cover HINGE BOLT 4A Remove the driver s side and passen STORAGE ger s side storage covers COVERS 52100003E 4B Lift storage tray cover and remove storage tray NOTE Some vehicles may have a different style storage tray See step 5 for instructions on how to remove the storage tray CNN LIFT STRAP _ aS 4C Remove spare tire cover NOTE The open portion of the cover is to the rear driver s side 52100003E 5 Open the center storage tray and turn the knobs counter clockwise to re lease Next remove the storage tray LOCKED NOTE This style of storage tray is optional on 7 some models 6 Using a nylon tool and a 10mm socket remove the driver s side and passenger s side cargo latch NOTE During reassembly make sure alignment i Q tab fits into the recess so latch sits flat a N CARGO LATCH 52100003E 7 Using a nylon tool remove the driver s side and passenger s side cargo net ring see image Remove the cargo net ring by Locating the slot in the ring Positioning the nylon tool in the slot Prying carefully with the nylon tool to release the cargo net ring Pulling the cargo net ring from the F side panel f SLOT PULL OUT Remove the jack and handle from the
5. passenger side storage box Using a 10mm socket and a 300mm extension remove the two 2 bolts NOTE Also remove the two 2 bolts from the driver s side storage box 8 52100003E 9A Remove the rear deck scuff plate and REAR latch cover SCUFF PLATE NOTE 2 See detailed inset of image j HA L7 9B Remove the push type clips zl IE 9C Using a nylon tool unlatch the clips located on the bottom of the rear scuff plate iu 10 Remove spare tire NOTE If equipped with a woofer before removing the spare tire unplug the lead wire from the woofer and remove the woofer 52100003E 11 Partially remove the driver s side and passenger s side rear door seal up to just above the tail light 12 Using a nylon tool slightly lift the trim panel Locate and verify the clip at tachments on the driver s and passen ger panels in two 2 places 13 Remove driver s side and passenger s PASSENGER SIDE side storage box OF THE VEHICLE N STORAGE BOX 52100003E 14 Remove and discard rubber grommet on the driver s side rear floor Remove each of the two clips off the vinyl protector Temporarily turn over the vinyl protector Remove the four bolts holding the BOSE amplifier NA f Move the BOSE amplifier to gain Jf lt 4 access to the ground bolt j
6. INSTALLATION INSTRUCTIONS 1 Description Tow Hitch Wire Harness Kit 2 Application Murano 2009 3 Part Number 999T8 0000 4 Illustration of the Completed Installation TOW HITCH TAIL LAMP TAIL LAMP A Er imd CONNECTORS GROUND oa Lae 5 c A AX A PES CONNECTOR GROMMET em HARNESS ne CONNECTOR DSCA P N LA990009 2134 52100003E 999T8 CU000 1 Revision November 27 2007 5 Kit Contents DESCRPTON am No DESCRIPTION am 1 Owner s manual including fuse 8 Nut M8 Packing foam tape Bolt M5 x 216 Converter Nut M5 Fuse 30A Exterior harness Plastic ties Tow hitch wire harness Plastic ties heat resistance Installation manual Bolt M8 x 216 2 52100003E 6 Tools Required Hand tools 3 8 drive ratchet 3 8 drive extension 300mm sockets 10mm 13mm combination wrench es 8mm 10mm torque wrench 32 inelb to 120 inelb small screwdriver and true flush cutters Special tools Nylon removal tool and plastic clip removal tool Other Fender covers proper clothing isopropyl alcohol NOTE Lay out all tools necessary to perform the installation Use appropriate tools and recommended special tools where specified 7 Installation Precautions 1 This manual contains installation procedures for the Nissan Murano tow hitch wiring harness and power converter In order to assure your
7. arness along the driver s side of the hitch member and secure it using the one 1 retain er clips and two 2 plastic ties heat resistant Temporarily secure the exterior wire harness to the hitch member using cloth tape before installing it onto the vehicle CLOTH TAPE 52100003E 19 20 4 Install the hitch member onto the vehicle according to the hitch member manufacturer s specifications A CAUTION Make sure the insulated portion of the wire harness is not pinched under the muffler hanger SEE CAUTION 5 Route the 4 pin exterior harness connector from under the vehicle and install the grommet into the vehicle NOTE Pass the grommet all the way through the hole and then seat the grommet Make sure the grommet is completely sealed Secure the tow hitch wire harness using one 1 plastic tie heat resistant 52100003E Connect the 4 pin exterior harness connector with the tow hitch wire har ness 4 pin connector 2 Secure the tow hitch wire harness using three 3 plastic ties A Remove the fuse box cover located 52100003E on the driver s side of the vehicle 22 10 Install the 30 amp fuse in the fuse box located next to the driver s side fender NOTE Some vehicles may already be equipped with a fuse from the fact
8. d lights switch All turn signal lights are flashing on both tester and vehicle With hazard lights switch on apply the foot Both stop lights on the vehicle are lit brake both turn stop lights on the tester and the turn lights on the vehicle are flashing Turn off the hazard light switch apply the Both turn stop lights on the tester and foot brake the stop lights on the vehicle are lit 52100003E 23 The following checks are to be performed with the ignition switch in OFF position Turn on headlamps Marker and tail lights on both tester and vehicle are lit Apply foot brake Stop lights on both tester and vehicle are lit Turn on left turn signal Left turn lights are not lit on both tester and vehicle Turn on right turn signal Right turn lights are not lit on both tester and vehicle Turn on left turn signal and apply foot Both stop lights are lit and not flash brake ing on both tester and vehicle Turn on right turn signal and apply foot Both stop lights are lit and not flash brake ing on both tester and vehicle With hazard lights switch on apply the foot All turn signal lights are flashing on brake both tester and vehicle Turn off the hazard light switch apply foot Both stop lights on the vehicle and brake the turn stop lights on the tester are lit but not flashing 24 52100003E 13 Reinstallation of Component
9. iler connector Yes Disconnect trailer and check vehicle towing connector with proper test light Is function OK No Y Is the trailer 30A fuse in the fusebox OK Yes Y Is the trailer lamp burned Replace trailer lamp with out a new one Check trailer Add or replace the 30A fuse No Y The wiring may be short Have additional trailer circuited towing fuse may lamps been added be blown or converter may have malfunction Yes Reduce number and size of lamps to maximum loads specified in Table 1 Y If the signal light inside the vehicle flashes rapidly bulb may need to Replace vehicle bulb be replaced Is the bulb bad No Check that the fuse is not blown on the vehicle side Table 1 MAX 7 8A STOP TURN RIGHT MAX 4 5A STOP TURN LEFT MAX 4 5A 52100003E 27 Rated Current Capacity 15 Wiring Diagram INTERIOR HARNESS FUSE 30A CONVERTER VEHICLE SIDE VEHICLE SIDE TURN RIGHT INPUT STOP TAIL TURN REAR COMBINATION LAMP RIGHT TURN LEFT INPUT TAIL INPUT STOP INPUT STOP TURN LEFT OUTPUT TAIL OUTPUT STOP TURN RIGHT OUTPUT GND STOP TAIL TAIL STOP EXTERIOR TURN L TURN R HARNESS TRAILER LAMP CONNECTOR 0 2 3 4 N n 7 8 1 T2 ala Q 28 52100003E
10. ory If there is a 30 amp fuse in this location it is not TRAILER LAMP necessary to install the fuse from the kit 30 AMP FUSE 52100003E 12 Operational Verification The following checks are to be performed with the ignition switch in ON position and the engine stopped Faults in wiring harness installation Correct routing of the wire harness Converter mounting Pushing or pulling of the converter by any outside force Wire harness Pinching of the wire harness Plastic tie locations Position of the plastic tie locations Removed parts Scratches or other damages Check the battery terminal for tightness Nut should have torque of with a 10mm socket and the battery cable 4 0 Nem 41 kgfecm 36 Ibfein angle is correct Turn on headlamps Marker tail lights on both tester and vehicle are lit Turn on left turn signal Left turn lights on both tester and vehicle are flashing Turn on right turn signal Right turn lights on both tester and ve hicle are flashing Apply foot brake Stop lights on both tester and vehicle are lit Turn on left turn signal and apply foot Left turn lights are flashing and right stop brake lights are lit on both tester and vehicle Turn on right turn signal and apply foot Right turn lights are flashing and left stop brake lights are lit on both tester and vehicle Turn on hazar
11. s Reinstall all parts temporarily removed from the vehicle Fuse box cover Fresh air intake Driver s and passenger side trim panel cargo net ring and package cover bolt Driver s and passenger side storage tray and jack holder Storage tray Spare tire and woofer if equipped Rear scuff plate and latch cover Driver and passenger storage tray covers Package cover if equipped Rear seat back cover A CAUTION Confirm that all rubber seals are properly installed on side panels and rear scuff plate Make sure the two 2 white clips are present and properly engaged ja A NM DOOR SEAL 2 Make sure the door seal is reinstalled properly on the driver s side rear door iL p CORRECT P d 52100003E 25 26 3 Make sure the door seal is reinstalled jm 07 CORRECT E DOOR SEAL 52100003E 14 Troubleshooting Perform the following sequence procedures if there is any lamp malfunction A CAUTION Check that the headlamp switch is OFF before removing replacing the bulbs Do the turn signal stop and tail lamps on the vehicle side operate normally Yes Yes Each lamp on the Each lamp on the trailer side is lit for trailer side is not lit a short time and then goes off No Yes Is the trailer connector No Check the connection of Eo securely connected tra
12. safety and the proper installation of this kit this manual should be read thoroughly It is especially important that all precautions are completely understood before start ing any installation task General information and some illustrations outlined in this installation manual are from Nissan Motor Co Ltd service manuals If installation will be carried out by more than one person pay special attention to ensure co worker s safety Make sure sufficient ventilation is provided while engine is running Take special care when working with heated rotating sliding or moving parts to prevent bodily injury When raising the vehicle refer to the appropriate manufacturer s service manual Take special care to ensure clearance between components such as brake parts fuel system and elec tric wires as specified in this publication If a problem is found with the tow hitch system due to installation refer back to the instructions to correct the problem Supplemental Restraint System SRS Air Bag Do not use electrical test equipment any circuit related to the SRS unless instructed to in the Service Manual For easy identification SRS wiring harnesses are covered with yellow insula tion either just before the harness connectors or for the complete harness Definition of Terms A WARNING This is used to indicate the presence of a hazard that could cause serious personal injury or death To avoid or reduce the risk the proced
13. ures must be followed precisely A CAUTION This is used to indicate the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle To avoid or reduce the risk the procedures must be followed carefully NOTE Provides additional information that facilitates installation work 52100003E 8 Preparation for Installation 1 Park the vehicle on level flat ground Turn off the ignition and engage the parking brake 2 3 Record all radio presets if necessary 4 Check that all vehicle lighting systems are functional headlamps brake lights turn signals side mark ers reverse lights etc 5 Disconnect the negative terminal of the battery 9 Component Removal NOTE When removing interior components place on a clean dry surface safe from damage soiling and loss Remove package cover Fold down both rear seat backs Using a 10mm socket remove the two 2 bolts then remove the deck latches using a nylon tool to release the retaining clips Open deck latch cover with nylon removal tool Remove the bolt using a 10mm socket Lift and remove the deck latch REAR SEAT BACKS a NOTE The latch has an alignment tab that fits into a recess 4 52100003E 2 Liftthe seat back cover by using the nylon tool at clip locations CLIP SEAT BACK NYLON COVER TOOL 3 Using a 13mm socket remove the two 2
Download Pdf Manuals
Related Search