OM/II Skid Steer POWER PLOW Snowplow Models 810SS/8611SS
Contents
1. 9716 9716 9 16 A 9716 B60007 56590 Lit No BG4091 Rev 09 12 Position the pivot beam and A frame near the mount locations at the rear of the blade Place the right and left group of hydraulic hoses connected to the slide box cylinders through the 1 1 2 diameter rubber grommet openings in the front face of the pivot beam mA B60272 June 15 2010 MOLDBOARD A FRAME ASSEMBLY 4 Position the pivot beam between the two support ribs until the connecting points on the beam align with those on the snowplow Insert one 3 4 x 3 clevis pin B50069 through each mounting hole and secure it with a 1 4 x 1 1 2 cotter pin 90601 5 Position each angle cylinder with the rod end of the cylinder in the pivot beam and the hydraulic hose port facing away from the A frame Secure the cylinder to the pivot beam with a 3 4 x 5 clevis pin 95739 and a 1 4 x 1 1 2 cotter pin 90601 Extend each cylinder rod until the cylinder base mounting hole aligns with the hole on the A frame angle cylinder bracket Insert another clevis pin and secure it with a cotter pin A 8611 Uses Outer Holes 810 Uses Inner Holes NOTE The 810SS and 8611SS models use the same A frame but use different mounting points fo2. END VIEW looking at connector Lit No B64091 Rev 09 21 June 15 2010 ELECTRICAL SCHEMATICS COIL HARNESS SS TR COIL HARNESS B62136 COILS 10VDC STAMPING ON END VIEW P N B62114 MANIFOLD looking at connector DRIVER SIDE SLIDE BOX RETRACT DRIVER SIDE SLIDE BOX EXTEND GREEN RIGHT ANGLE GROUND PASSENGER SIDE SLIDE BOX RETRACT C4 CONNECTSTO C3 PLASTIC ELECTRIC CONNECTOR MALE P N B62045 SILICONE RUBBER CABLE SEAL 18 ANG PIN B62096 MALE TERMINAL 18 16 ANG PIN B62097 LEFT ANGLE PASSENGER SIDE SLIDE BOX EXTEND GROUND 3 8 END RINGTERMINAL PIN B62118 gt 59 DRIVE SIDE RETRACT GROUND 510 BLUE BLACK DRIVE SIDE EXTEND BLUE WHITE GROUND BLUE S3 C4 GREEN 6 LEFT ANGLE RED BLACK GROUND RED WHITE BLACK S4 BROWN RIGHT ANGLE GROUND 51 PASS SIDE RETRACT GROUND 52 PASS SIDE EXTEND GROUND S5 PUMP SOLENOID GROUND Lit No B64091 Rev 09 22 June 15 2010 June 15 2010 Tas Joya XNid 3IIHAVGSH 9 46 T Nid OV 18 d3 5 45 ANJFIXI XO 1H9IH HNId 1IHA n 8 T dS LHDIa MOV Ig Q34 9 Nid JOVTa na 5 9
3. 769 mm Lit No B64091 Rev 09 27 June 15 2010 Problem Snowplow functions will not work after all connections are made or snowplow functions are slow Snowplow functions start and terminate suddenly Multiple valves function simultaneously Snowplow functions are reversed e g driver side wing extends when passenger side wing is activated from the control Both wings extend when the skid steer hydraulics are turned ON Snowplow angles only one way Wing will not stay angled when plowing Snowplow will not stay angled when plowing Wing will not move Snowplow will not angle Lit No B64091 Rev 09 TROUBLESHOOTING 55 coil is not magnetizing Solution 55 coil should magnetize with each function Solenoid cartridge valve may be contaminated or damaged A bent or overtorqued cartridge will not allow the valve to move freely inside of the cartridge Skid steer hydraulic fluid flow is set to variable flow Diodes may be corroded or damaged Determine a damaged cartridge valve by reversing the driver side and passenger side cartridge valves one at a time Replace valve if necessary For snowplow functions to work the skid steer hydraulic fluid flow should be set to continuous flow Review your skid steer operation manual for proper flow settings Clean diodes thoroughly and or replace Wire harness may be damaged Hydraulic hoses are connected wrong or coils and wir
4. Ta H IOVHIdHXOG 1341 JOVTa7 na STONV 1331 ania a STONV 3 dqWnr ANNONS MOV TE a aqWnr ANNONS MOV TE 2 VIN VIN a JOVTa7Nid V NOILONNA ELECTRICAL SCHEMATICS CONTROL HARNESS L HOLIMS FLY ld HOLIMS JO M3IA MOVE 6 2298 SLLZZ9 0LZZ99 SS3NHVH TOUYLNOI YL SS June 15 2010 19 Lit No B64091 Rev 09 ELECTRICAL SCHEMATICS VEHICLE HARNESS oosuuoo Buryool June 15 2010 8r ON3IX3XO8 IHON 3ITHAVGSH 81 IOVYIJFAY IHSIa 9v 18 d34H i 8L 1 1 41 31IHW3fn 18 H SL JIOVYIJAY X09 1 41 MIVTE INTE 9 Jooeuuoo 5uool 8t FIONV 1331 ame 81 3 I9NV NIJFYI 8L ANNOYS MOVI8 a SL SAN ANNOYS MOV 9 VIN VIN VIN 8 0 81 509 H3MOd MOVTE ANId V 00 NOILONNA 40102 190 000 0 0 f G3FSN LON STVNINYIJL WO YIGBANAY SS OX 3AOW3H 1ON L Jojoouuoo ye 1 1331 31IHW 3n18 v lt gt QN IX 1 Er MIIA VIN VIN VIN a 555655555565 VIN VIN
5. Joy8 yovia Siunwaau 2 SIHM G3H ma ki ana ansann GIN LIA 8 599visiass ka N33H5 e 3umwsms r 3umwama x xovigrm 6 5 oynayanna oOrwou Y o co LO OITwo u x a o 6LZZ9 LLZZIA 012299 981299 eeLzog veLcog ELZ9 26 98 sepniouj 181299 OILVMM HOS SS3N3VH 1016144 81 66 e UN3DGXOS IHS 9 amoa TOVWISU XoV8niNId L HOLIMS mov Ta ETIEN ama i Ny 1331 N3wod a FIONV IHSIa EMNENE Zi HOLIMS 1 HOLIMS June 15 2010 18 Lit No B64091 Rev 09 10joouuoo ye Buryoo ve 8b 3liHM 3n8 9 3L1IHM G33H 9 9 8L MOV Ig 3NId i MIVTBNINId d 8 8L Movigranig MIVTE GFY IHLON31 9MV 30105 30105 N 901 GNIS OL 1HVHO SIHL ASN HOLIMS NO SYSEWNN ON 1ON dOL OL 1HVHO SIHL ASN HOLIMS NO SYJAWNN ON 1ON dO GNI4 OL LYVHO SIHL 380 HOLIMS NO SU3YWAN ON 1ON 4 HOLIMS dN3IX3XO8 LH JAWIN IHON VAY i aNFIXI 1331 TIHAV
6. it may be necessary to turn ON the skid steer s auxiliary hydraulic switch prior to operating the snowplow Lit No B64091 Rev 09 25 The left switch on the control operates the driver side wing Push the switch UP to extend the wing and DOWN to retract the wing Push the center switch UP to angle left and DOWN to angle right The right switch operates the passenger side wing and works the same as the left switch Upon initiating the switches on the pistol grip control you may notice a snowplow function is slow or delayed The hydraulic fluid is filling the cylinders and replacing air in the system Monitor the hydraulic fluid level in your skid steer and fill as necessary No LED Float Light or Indicator Light NOTE This snowplow uses the skid steer controls for an emergency stop See skid steer manual for details June 15 2010 MAINTENANCE Periodically Check fasteners for tightness Torque to specifications Check hoses for wear and leaks Check cylinders for leaks inspect rod ends for corrosion and pitting Lubricate all exposed cylinder rod ends with liquid white lithium grease to prevent corrosion Check cutting edges and plow shoes for wear NOTE Do not discard plow shoe washers these should be retained for different shoe adjustments Clean and lubricate all electrical plugs and connections with dielectric grease Clean and install all dust caps prior to storing Lubricate all pins and bu
7. Beam 8 Manifold Parts All Models td 31 Control Accessories 8 Kits All Models 33 June 15 2010 SAFETY SAFETY DEFINITIONS WARNING Indicates a potentially hazardous situation that if not avoided could result in death or serious personal injury 4 CAUTION Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices NOTE Indicates a situation or action that can lead to damage to your snowplow and vehicle or other property Other useful information can also be described DISMOUNT INSTRUCTIONS Read Owner s Manual for Complete Instructions Lower the snowplow on a flat level surface and turn the engine OFF low attachment plate Disconnect the snowplow wire harness from the skid steer rd and position the top edge ofthe plate underthe PE receiving pocket on the top edge of the snowplow attachment plate Connections located on the skid steer Slow raise the rms onthe skid steer and tt he skid steer plate toward the cab I T VS a oo until the snowplow attachment plate is flush with the skid steer plate Turn the The skid steer locking levers shall with the snowplow les both locking levers on the skid steer by rotating each handle 90 into a Boao TETTE postion The skid steer eels shall steer plate forward away from
8. CAUTION Improper installation and operation could cause Transport speed should not exceed damage Read and understand labels and the Further reduce speed under adverse travel Owner s Manual before installing operating or making conditions adjustments A CAUTION WARNING Plowing speed should exceed 10 mph Lower blade when vehicle is parked Temperature changes could change HYDRAULIC SAFETY hydraulic pressure causing the blade to drop unexpectedly or damaging hydraulic components Failure to do this could result in serious personal injury A WARNING Hydraulic fluid under pressure can cause skin injection injury If you are injured by hydraulic fluid get medical attention immediately A WARNING The driver shall keep bystanders clear of Always inspect hydraulic components and hoses the blade when it is being raised lowered or before using Replace any damaged or worn parts angled Do not stand between the vehicle and immediately the blade or within 8 feet of a moving blade A moving or falling blade could cause personal If you suspect a hose leak DO NOT use your injury hand to locate it Use a piece of cardboard or wood A WARNING FUSES Do not exceed vehicle operative capacity including the blade See vehicle rating label The snowplow electrical and hydraulic systems contain several blade style automotive fuses If A WARNING a problem should occur and fuse replacement is necess
9. Seal Kit Cyl B60207 B60366 Combo Seal Kit Cyl B60221 B60324 B60373 Combo Seal Kit Cyl B60347 96028 Moldboard Label Pack 96032 Moldboard Label Pack ns not shown Lit No B64091 Rev 09 35 June 15 2010 e Blizzard PETAL LL 80x 248038 Milwaukee WI 53224 9538 SNOWPLOWS www blizzardplows com CE dd A DIVISION OF DOUGLAS DYNAMICS L L C Copyright 2010 Douglas Dynamics L L C All rights reserved This material may not be reproduced or copied in whole or in part in any printed mechanical electronic film or other distribution and storage media without the written consent of Blizzard Authorization to photocopy items for internal or personal use by Blizzard outlets or snowplow owner is granted Blizzard reserves the right under its product improvement policy to change construction or design details and furnish equipment when so altered without reference to illustrations or specifications used Blizzard or the vehicle manufacturer may require or recommend optional equipment for snow removal Do not exceed vehicle ratings with a snowplow This product is manufactured under the following U S patents 5 420 480 5 638 618 5 899 007 6 178 669 6 253 470 6 276 076 6 393 737 6 408 549 6 412 199 6 442 877 6 615 513 7 134 227 7 430 821 RE35 700 CAN patents 2 060 425 2 184 922 2 229 783 2 259 508 2 358 145 2 358 354 2 466 195 and other patents pending Blizzard offers a limited warranty for all snowplows
10. VIN j VIN VIN VIN OL EG 1993133 1331 ov1g 3n18 6 a EG 12 1 XO LHOIH xov 1g Q34H 8 VIN VIN VIN L VIN VIN VIN 9 VIN VIN VIN S 1397 ana 7 552525 5 55525555525552525555505255550525555050555505555555 2 ONY HON DY RRR AIR AIR IR KIKI K KARL PIK KK KK KRI VIN VIN VIN VIN VIN VIN L 8L QaNnosuo Move MV NOILONNA 30105 JAvNDS ONTd sddVZZIT ccLZ9 Zelzog SSINAYVH 1OIH A 1 SS 20 Lit No B64091 Rev 09 ELECTRICAL SCHEMATICS SNOWPLOW HARNESS SS TR PLOW HARNESS B62134 B62135 AWG 18 FUNCTION DUMP SOLENOID N A N A GROUND RIGHT ANGLE LEFT WING RETRACT LEFT WING EXTEND RIGHT WING RETRACT RIGHT WING EXTEND COLOR BROWN N A N A BLACK GREEN BLUE BLACK BLUE WHITE RED BLACK RED WHITE END VIEW looking at connector n DD connector END VIEW looking at BLIZZARD PLUG SQUARE 9 co o L lt lt lt col lt co amp lt I vol 22222929229 O ki 212 tel 55 lt glo 42225202205 rt di 216 Li iva aj m u Oui j I 5 aly o a ra 7 x E 2 9 96 EE RSS SESS EE 515 191212120 oja 15 5 z oeloes a
11. and accessories See separately printed page for this important information The following are registered 9 or unregistered trademarks of Douglas Dynamics L L C BLIZZARD BLIZZARD POWER PLOW BUCKET BLADE POWER PLOW WIDE PASS Printed in U S A Lit No B64091 Rev 09 June 15 2010
12. top edge of the plate under the receiving pocket on the top edge of the snowplow attachment plate Slowly raise the arms on the skid steer and tilt the skid steer plate toward the cab until the snowplow attachment plate is flush with the skid steer plate Turn the engine OFF Engage both locking levers on the skid steer by rotating each horizontal position The skid steer locking levers shall insert into the snowplow lever receiving holes Attach all hydraulic hoses on the snowplow to the auxiliary hydraulic connections located on the skid steer On some skid steer models it may be necessary to initiate an auxiliary hydraulic switch on the skid steer prior to operating the snowplow Connect the snowplow wire harness to either the pistol grip control or auxiliary electrical connection on the skid steer NOTE If at any time the Mounting and Dismounting Instructions label or any other label attached to your snowplow becomes illegible promptly replace them DISMOUNT INSTRUCTIONS Read Owner s Manual for Complete Instructions An 4 m Hole Snowplow Receiving Attachment Pocket Plate Lower the snowplow on a flat level surface and turn the engine OFF Disconnect the snowplow wire harness from the skid steer Disconnect all hydraulic hoses on the snowplow from the auxiliary hydraulic connections located on the skid steer Disengage both locking levers on the skid steer by rotating each handle 90 into a vertical position Th
13. x 1 1 2 Cotter Pin 3 4 x 9 Wing Slide Box Pivot Pin 1 x 11 1 8 Wing Slide Box Pivot Pin 2 51 64 OD 2 9 32 ID x 1 2 Black Polyethylene Plug Hydraulic Cylinder Slide Box Extend Retract Hydraulic Cylinder Slide Box Extend Retract 5 8 11 Locknut 9 16 18 Male ORB Hydraulic Adapter 9 16 18 45 Adjustable Elbow ORB Hydraulic Adapter 3 8 x 36 Slide Box Extend Retract Hydraulic Hose 5 8 ID 3 4 OD x 1 Black Vinyl Cap 5 8 x 11 1 2 Slide Box Extend Retract Hydraulic Cylinder Base End Pin 1 8 x 2 5 8 Hair Cotter Pin 5 8 Hardened Washer 30 June 15 2010 A FRAME PIVOT BEAM 8 MANIFOLD PARTS ALL MODELS Pivot Beam Pivot Beam 1 B52141 1 1 4 B41052 1 4 x 1 1 2 Cotter Pin g G June 15 2010 31 Lit No B64091 Rev 09 A FRAME PIVOT BEAM amp MANIFOLD PARTS ALL MODELS B50069 95739 B61330 B61008 B61217 B60029 B60324 B60223 B60224 56590 B70143 B70134 90055 29233 B61514 66439 B61307 B60086 B70132 B61034 B61275 B60341 B60342 B60491 B60354 B60355 B60089 B60320 B60356 B60183 B60225 B60272 B60279 B60227 B60168 B62163 B60166 B60052 B62161 B60321 B62164 B60278 B60226 B60049 B61203 B63196 B60322 N A AD h SD N NWA i AD A as op Son OAD 3 4 x 3 Clevis Pin 3 4 x 5 Clevis Pin 1 8 x 9 Hex Cap Screw G8
14. 09 NOTE Where applicable Model 8611 values are in parentheses 15 June 15 2010 HYDRAULIC GUIDE Models 810ss 8 8611ss NOTE Check valves CV1 amp CV3 are not illustrated Both valves are located on the opposite side of the manifold in the diagram shown above Hydraulic Valve amp Hose Port Guide Recommended for machines equipped with auxiliary hydraulics having a flow rated at 4 30 gallons per minute gpm and a maximum pressure rating of 3 000psi HYDRAULIC HOSES Angle Right Driver Side Cylinder Angle Left Passenger Side Cylinder Driver Side Slide Box Retract Driver Side Slide Box Extend Passenger Side Slide Box Extend Passenger Side Slide Box Retract RELIEF amp CHECK VALVES Driver Side Wing Pressure Relief Driver Side Wing Anti Cavitation Passenger Side Wing Anti Cavitation Passenger Side Wing Pressure Relief Angle Relief Driver Side Slide Box Retract Check Valve Driver Side Slide Box Extend Check Valve Passenger Side Slide Box Retract Check Valve Passenger Side Slide Box Extend Check Valve Back Pressure Check Valve NOTE Energize the following solenoids for the functions Passenger Side Slide Box Retract Passenger Side Slide Box Extend Angle Left Passenger Side Cylinder Angle Right Driver Side Cylinder Driver Side Slide Box Retract Driver Side Slide Box Extend Milwaukee Wisconsin 53224 B63196 Lit No B64091 Rev 09 16 June 15 2010 ELECTRICA
15. 1 8 Top Locknut GC Distorted Thread 1 1 2 ID 2 1 8 OD Black Rubber Grommet 60 Durometer Hydraulic Cylinder Snowplow Angle Hydraulic Cylinder Snowplow Angle 3 8 x 26 Snowplow Angle Hydraulic Hose 3 8 x 36 Snowplow Angle Hydraulic Hose 9 16 18 90 Adjustable Elbow Hydraulic Adapter ORB A Frame Rubber Mat A Frame Cover Plate 3 8 16 x 1 1 4 Hex Cap Screw G8 3 8 SAE Hardened Washer 3 8 16 x 4 Hex Cap Screw G5 3 8 16 x 1 1 2 Hex Cap Screw G5 3 8 Internal External Tooth Lock Washer 3 4 x 78 Hydraulic Hose A Frame 3 8 16 Hex Locknut GC 3 8 16 U Nut Manifold Assy Manifold Assy Pump Manifold Kit Incl B60402 1 B60447 1 B60448 1 B62039 1 B61011 2 B61412 2 B61312 2 B61637 2 56805 4 Manifold Block with Cross Port Relief Clear Anodized Aluminum Manifold Block with Cross Port Relief Gold Anodized Aluminum 1 1 16 12 Male ORB Connector Hydraulic Adapter Spool Valve 2 Way Back Pressure Check Valve 5 psi Pressure Compensation Regulation Valve Check Valve 50 psi 9 16 18 Adjustable Elbow Hydraulic Adapter Relief Valve 1500 psi Relief Valve 2650 psi Relief Valve 3000 psi Coil PDL 12V DC Spool Valve 3 Way 2 Position 1 2 20 Hex Jam Nut Coil Harness Assy Incl Items B62045 B62118 2 B62116 5 B62096 7 62097 7 Items 32 36 Spool Valve 4 Way 3 Position Coil LDL 12V DC Relief Valve 1700 psi Relief Valve 2800 psi SAE Hollow Hex Plug ORB 1 Washer Label SS TR
16. 1626 5 8 11 Flanged Locknut B51042 1 Wing DS B51100 1 Wing DS 96325 1 Wing Decal DS 96329 Wing Decal DS B51048 Cutting Edge Driver Side Wing T1 B51069 Cutting Edge Driver Side Wing T1 Lit No B64091 Rev 09 29 June 15 2010 MOLDBOARD 8 WING PARTS ALL MODELS B50057 B50075 29593 49071 60045 91192 93010 B61383 B61681 B61384 B61049 68494 91332 B51043 B51101 96326 96330 B51047 B51070 B61418 B61360 B61419 B61622 B61362 B50058 B50074 B61416 B61398 23039 B61385 90601 B51009 B13307 B61425 B60347 B60207 91337 B60007 B60272 B60224 B61198 B11989 B61030 90576 N IO DA A gt BRA mM Lit No B64091 Rev 09 ae DS Slide Box DS Label Multiple Pinch Points HD Disc Shoe Assy 1 1 8 ID 1 5 8 OD x 1 1 2 Spacer 1 Flat Washer 7 16 x 1 3 4 Linchpin 5 16 18 x 2 1 4 Hex Cap Screw G8 1 x 4 1 8 Slide Box Stop Pin 5 16 18 Locknut G8 Plow Guide Assy Set of 2 5 16 18 x 1 Hex Cap Screw G5 5 16 18 Locknut GB Wing PS Wing PS Wing Decal PS Wing Decal PS Cutting Edge PS T1 Cutting Edge PS T1 1 2 13 x 3 1 2 Carriage Bolt G8 1 2 13 x 5 Carriage Bolt G8 1 2 13 x 4 1 2 Carriage Bolt G8 1 2 13 x 5 3 4 Carriage Bolt G8 1 2 13 x 6 1 2 Carriage Bolt G8 Slide Box PS Slide Box PS 5 8 11 x 7 3 8 Spade Bolt G8 13 OAL x 2 OD x 5 16 Extension Spring Trip Spring 5 8 x 3 Clevis Pin 1 4
17. 8 Xovignnma QN31X3 XO8 1331 FLIKWAaNT8 H INid na IOVHI3H XO8 1431 Movg 3n8 9 3Nid N3SH5 Nasu ISNY 1441 ania SNid NMOUH STONV LH9IH 339 u3dWnr ANNOYS MOVE a VIN VIN fe Cel v9 VIN VIN 8 VIN VIN NOILONNA 0705 N H 84 ANJFIXI LH IY M 9 r 84 lOVHIldMH MOV Ig Q34 r 8l aN31X4 XO8 1551 FLIHWAaNT9 H 8L lOVHIJMXOS8 1351 Mov Igrania 9 8L FTONV 1351 anid 8L 3 IONV LH9IH 339 8L MOV Id a a B a Jooguuoo VIN VIN VIN 5 Bunool 5uool a ih a Sa SN dwnd NS E MIIA SMV NOILONNA v a ceo 3 8 a 29 298 saaoia M SSINAYVH 1OdINOO VITIXTnV ELECTRICAL SCHEMATICS AUXILIARY CONTROL HARNESS OPTIONAL Lit No B64091 Rev 09 MOUNTING 8 DISMOUNTING INSTRUCTIONS Prior to operating your POWER PLOW snowplow review the Mounting and Dismounting Instructions label on the back of the driver side moldboard Read Owner s Manual for Complete Instructions V Lever Receiving Hole Snowplow Attachment Pocket Plate Position the skid steer close to the snowplow and align the mount points on the Skid steer plate with the snowplow attachment plate Tilt the skid steer plate forward and position the
18. 9 to ports T and P on the manifold Connect a hydraulic hose B60086 to each adapter Tighten fittings and hoses per torque chart Gea i 1 STE June 15 2010 GENERAL SYSTEM SCHEMATICS ELECTRICAL SCHEMATIC gt 4 S10 S9 OO BOTTOM TOP LEFT SLIDE BOX HYDRAULIC SCHEMATIC ron ANGLE RIGHT SLIDE BOX LEFT ANGLE 80 7 1 2 9 gt 40 RV2 RV3 1500 PSI 3000 PSI 1500 PSI RV1 2650 PSI Paj RVS RV4 2650 PSI 1700 PSI 1700 PSI 2800 PSI frel 2800 PSI cV1 CV2 lke CV4 50 PSI 50 PSI 50 PSI 50 PSI 55 CV5 X is 5 PSI y PC 50 PSI Lit B64091 Rev
19. Hydraulic Hose Guide Piston Assy G Grade ns not shown Lit No B64091 Rev 09 32 June 15 2010 CONTROL ACCESSORIES amp KITS ALL MODELS B62131 B62132 B62133 B62134 B62135 B62045 B62097 B62096 B62116 B62046 B62100 B62093 B62118 B62072 B62218 B62219 B62211 B70040 B62210 B70048 90055 29233 B70049 91333 mounting hardware Control Rugged and durable the 3 8 thick 2 ply construction keeps snow off your windshield and in its place on the ground The one piece rubber design allows for wing clearance and provides optimum snow deflection The deflector is shipped with a POWER PLOW vinyl decal and complete 810SS 8611SS Description Pistol Grip Control Wire Harness Assy Incl Items 1 5A Wire Harness Extension Vehicle Side Weather Cap Vehicle Side Wire Harness Extension Wire Harness Extension Snowplow Side Weather Cap Snowplow Side Wire Harness Extension Connector Electric Male Plastic Terminal Male 18 16 AWG Seal Cable Silicone Orange 18 AWG Plug Cavity Silicone White 18 16 AWG Connector Electric Female Plastic Terminal Ring 10 22 18 AWG Terminal Female 18 16 AWG 3 8 End Ring Terminal 3 8 End Ring Terminal Snowplow Side Wire Harness Extension Harness SS Snowplow Side Extension 4 Housing SS Pistol Grip 2 Halves w Screws B61613 Circuit Board and 3 Switch Assy Mount Bracket Vehicle Side Harness Control w Pipe SS Pistol Grip Con
20. June 15 2010 Lit No B64091 Rev 09 BLIZZARD TMEY NUES ENTE 2 a a yi WO NE EE GINEN TET 2 22 9 47 7 Mi BUZZARD POWER PLOW Models 81055 8 861155 POWER PLOW Snowplows Installation Instructions amp Owner s Manual A CAUTION See your BLIZZARD sales outlet Web site for specific vehicle application recommendations before installation The Undercarriage Selection Guide has specific vehicle and snowplow requirements A CAUTION Read this document before installing the snowplow A CAUTION Read this document before operating or servicing snowplow This manual supersedes all editions with an earlier date PREFACE Congratulations on purchasing the most advanced skid steer snowplow available The POWER PLOW snowplow is clearing new trails for innovative design rugged durability quality craftsmanship and superior performance Our innovative products are tested all over the snowbelt This manual provides safety operation and maintenance information for your new BLIZZARD snowplow To keep your snowplow in good condition read and understand this manual and follow its recommendations Failure to do so may affect your warranty coverage Lit No B64091 Rev 09 When service is necessary your local BLIZZARD distributor knows your snowplow best Contact your BLIZZARD outlet for maintenance service or any other assistance you require If you have not already done
21. L INSTALLATION 1 Connect the manifold coil harness to the snowplow harness Feed the opposite end of the snowplow harness through the top access hole in the A frame same as 3 4 tank hydraulic hose located on the driver s side 2 Attach the grounds on the coil wire harness and snowplow harness with a 3 8 x 1 1 2 cap screw and 3 8 tooth lock washer to the A frame Secure the wires with a locknut Review the diagram for the proper ground location Ground Mount Hole 4 Manifold Mount Holes 3 Connect the snowplow harness to the vehicle harness and then the vehicle harness to the pistol grip control harness Attach the ground wire from the vehicle harness to the cab of the skid steer The pink black power wire connects to a switched power source with a minimum of 12 volts NOTE The pink black power wire MUST be switched ON and OFF with the ignition Lit No B64091 Rev 09 4 Position the vehicle harness mount bracket in an accessible location for easy on and off installation inside the skid steer Secure the vehicle side harness in the notch on the bracket 5 Find an accessible location inside the skid steer for the control harness mount bracket either positioned vertically or horizontally depending on user preference When choosing a location for your bracket it should be mounted in easy reach of the vehicle operator and not restricting access to vehicle controls or vehicle ins
22. al application roadway intersections D WIDE PASS Position Angled with Wing Forward Primary position for accelerated angled plowing For use in directional plowing cornering diverting snow away from objects or buildings Ideal application plowing adjacent to buildings driveway road intersections Lit No B64091 Rev 09 8 June 15 2010 UNPACKING 8 INSPECTION Your POWER PLOW snowplow has been packaged to withstand transit and weather related damage Fully inspect all components upon receipt of your snowplow In the event of shipping damage or missing parts immediately contact our Customer Service Department at 1 888 680 8600 Begin unpacking and inspection in the following order 1 Remove the shipping document from the end panel of the pallet wrap Retain all documentation for your records 2 All wood framing and polyethylene material should be removed from the pallet for easy access to the snowplow 3 Due to the odd shaped components and size of several assembly parts various cable ties and corrugated material are used for scratch resistance and package orientation Please remove these items prior to assembly 4 Place the main blade assembly on a flat level surface Lit No B64091 Rev 09 Once you have inspected all parts and removed all packaging materials your snowplow is ready to be fully assembled Retain this information for your reco
23. ary the replacement fuse must be of the same type and amperage rating as the original Installing a fuse with a higher rating can damage the system and could start a fire Fuse Replacement including fuse ratings and locations is located in the Maintenance A WARNING Section of this Owner s Manual Never stand work or reach under lift arms or lift cylinders without employing a lift arm stop or stand To prevent accidental movement of the blade always turn the control OFF whenever the snowplow is not in use The power indicator light will turn OFF A CAUTION Read Owner s Manual before operating or servicing snowplow Lit No B64091 Rev 09 5 June 15 2010 SAFETY PERSONAL SAFETY Remove ignition key and put the vehicle in park or in gear to prevent others from starting the vehicle during installation or service Wear only snug fitting clothing while working on your vehicle or snowplow Do not wear jewelry or a necktie and secure long hair Wear safety goggles to protect your eyes from battery acid gasoline dirt and dust Avoid touching hot surfaces such as the engine radiator hoses and exhaust pipes Always have a fire extinguisher rated BC handy for flammable liquids and electrical fires FIRE AND EXPLOSION A WARNING Gasoline is highly flammable and gasoline vapor is explosive Never smoke while working on vehicle Keep all open flames away from gasoline tank and
24. e Undercarriage Selection Guide has specific vehicle and snowplow requirements Vehicle application recommendations are based on the following The vehicle with the snowplow installed must comply with applicable Federal Motor Vehicle Safety Standards FMVSS The vehicle with the snowplow installed must comply with the vehicle manufacturer s stated gross vehicle and axle weight ratings found on the driver side door cornerpost of the vehicle and the front and rear weight distribution ratio In some cases rear ballast may be required to comply with these requirements Lit No 64091 Rev 09 BLIZZARD Undercarriage Selection Guide is based on available vehicle capacity for snowplow equipment on a representative vehicle equipped with options commonly used for snowplowing and with 300 Ib of front seat occupant weight Weights of front seat occupants can be adjusted above 300 Ib but vehicle with snowplow must not exceed vehicle GVWR or GAWR In some cases there may be additional limitations and requirements Installation modification and addition of accessories must comply with published BLIZZARD recommendations and instructions Available capacity decreases as the vehicle is loaded with cargo or other truck equipment or snowplow accessories are installed If there is uncertainty as to whether available capacity exists the actual vehicle as configured must be weighed June 15 2010 OPERATION You
25. e skid steer locking levers shall withdraw from the snowplow lever receiving holes Turn the enaine ON Slowly lower the arms on the skid steer and tilt the skid steer plate forward away from the cab until the top edge of the skid steer plate clears the receiving pocket on the top edge of the snowplow attachment plate Back the skid steer away slowly U S Patents 5 638 618 5 899 007 6 178 669 6 276 076 6 393 737 6 408 549 6 412 199 6 442 877 6 615 513 CAN Patents 2 184 922 2 229 783 2 259 508 2 358 145 2 358 354 2 466 195 and other patents pending Lit No B64091 Rev 09 24 June 15 2010 TESTING YOUR SNOWPLOW 1 To test all of the functions on the POWER PLOW snowplow your snowplow needs to be properly attached to the skid steer Refer to the Mounting and Dismounting label on the back of the snowplow 2 Complete the hydraulic connections with the skid steer turned OFF NOTE Due to the various makes and models of skid steers available hydraulic couplings for the auxiliary hydraulic connections are not provided Consult your skid steer s owner s manual for the appropriate couplings needed Connect the couplings to the hoses for the pressure port P and the tank port T on the manifold Complete the hydraulic installation by making the appropriate connections at the skid steer 3 Start the skid steer and begin to initiate the blade functions NOTE Depending on the skid steer model
26. eads are clean and free of damage 8 10 Lubricate the threads and the O ring with 10W hydraulic fluid 13 15 For an adjustable ORB completely back off the locknut and washer 17 21 Hand tighten the fitting until it contacts the port spotface Point the elbow or tee in the desired 22 25 direction and hold 40 43 Torque to specification 43 57 68 75 Torque values specified are for threads lubricated with 10W hydraulic fluid 90 99 112 123 146 200 154 215 218 290 Lit No B64091 Rev 09 11 June 15 2010 MOLDBOARD amp A FRAME ASSEMBLY 1 Remove dust cap from both of the slide box cylinders located at the center rear of the moldboard Attach adapters B60007 for 810SS B60272 for 8611SS to both ports on each slide box cylinder Tighten fittings per torque chart NOTE All ofthe hydraulic adapters can be found packaged with the manifold assembly O NOTE The positions for the rod and base end slide box hoses The hoses that operate the retract functions rod of the cylinders are closest to the base of each cylinder The hoses that operate the extend functions base of the cylinders are closest to the rod of each cylinder 2 Connect hoses B60224 to each of the hydraulic adapters on the cylinders Tighten hoses per torque chart NOTE Review the label on each hose for the appropriate part number
27. htening Torque Diameter Clamp Loads Tightening Torque mm Ib Lubricated Dry mm Ib Lubricated Dry 3 ft lb 5 ft lb 1 987 5 ft lb 7 ft lb 6 ft lb 8 ft lb 2 812 8 ft lb 11 ft lb 10 ft lb 13 ft lb 4 044 14 ft lb 19 ft lb 14 ft lb 19 ft lb 5 121 20 ft lb 27 ft lb 28 ft lb 37 ft lb 8 116 40 ft lb 53 ft lb 49 ft lb 65 ft lb 11 796 70 ft lb 92 ft lb 77 ft lb 103 ft lb 16 092 111 ft lb 148 ft lb 125 ft lb 167 ft lb 21 970 173 ft lb 231 ft lb 172 ft lb 229 ft lb 26 868 238 ft lb 317 ft lb 244 ft lb 325 ft lb 34 284 338 ft lb 450 ft lb Lit No B64091 Rev 09 10 June 15 2010 TORQUE SPECIFICATIONS Turns Size Assembly Steps min max 6 7 Make sure the tubing and threads are clean 8 9 Lubricate the threads with 10W hydraulic fluid 11 12 Hand tighten the nut sleeve to approximately 30 in Ib 14 15 Make alignment marks on the nut and fitting 18 20 Tighten to turn or torque specification 36 39 When fully tightened make a second set of alignment marks at the fully tightened position 57 63 79 88 Torque values specified are for threads lubricated with 10W hydraulic fluid 94 103 Overtightening will reduce the clamping force resulting in loss of seal and reduction of flow 108 113 127 133 158 167 245 258 O Ring Boss Torque Values Size Assembly Steps min max 6 7 Verify the port O ring sealing surfaces and thr
28. ing are incorrect Pressure P and tank T hoses are installed in the wrong position on the skid steer Skid steer computer conflicts with cylindrical connection The wing pressure relief valve is contaminated The angle pressure relief valve is set too low NOTE Increasing the pressure relief valve will cause damage to your snowplow Do not set the pressure relief greater than 3000 psi Control station harness or cables may be loose or improperly connected Verify harness is not damaged Review schematic s to troubleshoot connection s Replace if needed Review the Hydraulic Valve and Hose Port Identification Guide under the A frame cover for proper port locations and or place respective coils over correct valves Review the skid steer operation manual to determine the pressure and tank connections Using a jumper wire connect pin K to pin L at the back of the cylindrical connector cylindrical connector only Test the wing pressure relief Attach a T fitting with a fluid psi gauge to the base end of the wing cylinder Pressure relief should not be greater than 1700 psi 2800 psi for 8611SS Replace if less than 1500 1700 psi 2600 2800 psi for 861155 Follow the guidelines indicated above however the psi setting should not exceed 3000 psi NOTE If the snowplow is floating back when angled to the right adjust the left pressure relief valve and vice versa Verify control station harness and all cables a
29. lines Wipe up any spilled gasoline immediately Be careful when using gasoline Do not use gasoline to clean parts Store only in approved containers away from sources of heat or flame CELL PHONES A driver s first responsibility is the safe operation of the vehicle The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road Wait until it is safe to operate Mobile Communication equipment such as cell phones or two way radios Lit No B64091 Rev 09 VENTILATION A WARNING Vehicle exhaust contains lethal fumes Breathing these fumes even in low concentrations can cause death Never operate a vehicle in an enclosed area without venting exhaust to the outside BATTERY SAFETY A CAUTION Batteries normally produce explosive gases which can cause personal injury Therefore do not allow flames sparks or lit tobacco to come near the battery When charging or working near a battery always cover your face and protect your eyes and also provide ventilation Batteries contain sulfuric acid which burns skin eyes and clothing Disconnect the battery before removing or replacing any electrical components NOISE Airborne noise emission during use is below 70 dB A for the snowplow operator June 15 2010 VEHICLE APPLICATION INFORMATION 4 CAUTION See your BLIZZARD outlet for specific vehicle application recommendations before installation Th
30. o proper specifications o o0 j NOTE All ports identified by stamped number on the manifold The numbers also identify the hydraulic functions which can be referenced on the label under the manifold cover 9 Remove the A frame cover to gain access to the inside of the manifold compartment 10 Attach the manifold to the A frame using cap screws B61514 washers 29233 and locknuts B61034 Ground Mount Hole Lit No B64091 Rev 09 NOTE When handling the manifold hold the manifold at the sides of the block Never handle the manifold by coils Doing so can cause a solenoid cartridge to bend causing the cartridge to stick when activated 11 Route the hydraulic hose groupings from the pivot beam to the access holes located on the sides of the A frame Connect the hoses to their respective adapters on the manifold 12 Remove the dust cap from both of the hydraulic angle cylinder ports and attach one 9 16 90 adjustable elbow ORB adapter to each port Each adapter should be angled toward the top of the moldboard Connect one 3 8 x 26 36 for 8611 hydraulic hose B60223 or B60224 to each angle cylinder adapter Be careful not to overtighten the hose connections Tighten fittings and hoses per torque chart 13 Connect the hoses to their respective adapters on the manifold Tighten hoses per torque chart 14 Install adapters B6008
31. r POWER PLOW snowplow is the most advanced and versatile snowplow on the market The easy A WARNING to use controls allow you to automatically adjust the Never use the snowplow attachment to carry snowplow blade and wings into an infinite number of people as a man lift or as a work platform plowing positions Review the illustrations below to determine the best position for your plowing needs A WARNING A When plowing with down pressure do not cause the front wheels on the skid steer tractor to raise above ground A Compact Position 8 or 8 6 Blade Width o Primary position when transporting the snowplow E SEEL For use in heavy snow conditions with poor visibility initial clearing and tight quarters Ideal application residential driveways small B roads WIDE PASS Position 10 or 11 3 Blade Width Primary position for clearing large surfaces For use in light snow conditions with good visibility final clearing and clean up Ideal application large parking lots widening roadways C BUCKET BLADE Position 9 3 or 9 10 Blade Width Primary position for transporting snow reye 4 e For use in initial clearing with decent visibility transporting large volumes of snow final clean up Ide
32. r the angle cylinders due to different stroke lengths on the cylinders Be sure to use the proper mounting point when replacing or installing cylinders NOTE The cylinder ports should be facing away from the A frame Lit No B64091 Rev 09 13 Hook each extension spring to the receiving holes on the pivot beam and attach the opposite end of the spring to its respective spade bolts Install the spade bolts through the extension spring mounting angle on the top rear of the blade Secure each spade bolt by placing one 5 8 flat washer on the bolt and thread one 5 8 locknut Tighten each locknut until a piece of paper can pass between the 3rd and 4th coils on the spring Install the blade guides at each end of the moldboard Insert the cap screw through the holes at the top of the wing reinforcement rib Tighten all screws with locknuts June 15 2010 MOLDBOARD amp A FRAME ASSEMBLY 8 Assemble the manifold Each of the hose ports on the manifold is covered with stretch wrap Remove the wrap and install adapter B60272 in ports 1 2 7 8 9 and 10 Tighten fittings per torque chart a Cmi eis S9 S1 S5 II II III Nei 90 NOTE DO NOT let any foreign objects enter into the open ports The valves can become contaminated and greatly hinder the snowplow s performance Torque t
33. rds Date of Purchase Dealer Distributor Dealer Phone Number Snowplow Serial Number Register your snowplow online at www blizzardplows com June 15 2010 TORQUE SPECIFICATIONS TORQUE CHART CAUTION Read instructions before assembling Fasteners should be finger tight until instructed to tighten according to the torque chart Use standard methods and practices when attaching snowplow including proper personal protective safety equipment Grade Identification for J429 Grade 5 Bolt Grade Identification for J429 Grade 8 Bolt SAE J429 Grade 5 Torque Values SAE J429 Grade 8 Torque Values Nominal Clamp Loads Tightening Torque Clamp Loads Tightening Torque Thread Size Ib Lubricated Dry Thread Size Ib Lubricated Dry 1 4 20 1 4 20 5 16 18 5 16 18 3 8 16 3 8 16 7116 14 7116 14 1 2 13 9 050 57 ft lb 75 ft lb 1 2 13 12 800 80 ft lb 107 ft lb 9 16 12 11 600 82 ft lb 109 ft lb 9 16 12 16 400 115 ft lb 154 ft lb 5 8 11 14 500 113 ft lb 151 ft lb 5 8 11 20 300 159 ft lb 211 ft lb 3 4 10 21 300 200 ft lb 266 ft lb 3 4 10 30 100 282 ft lb 376 ft lb 7 8 9 29 435 321 ft lb 430 ft lb 718 9 41 550 454 ft lb 606 ft lb 1 8 38 600 482 ft lb 640 ft lb 1 8 54 540 680 ft lb 900 ft lb 8 8 Grade Identification for Metric Grade 8 8 Bolt Grade Identification for Metric Grade 10 9 Bolt e e Metric Class 8 8 Torque Values Metric Class 10 9 Torque Values Diameter Clamp Loads Tig
34. re securely connected Clean if necessary No power to the cartridge valve Verify S9 and S10 coils passenger side slide box retract and extend and S1 and S2 driver side slide box retract and extend are connected properly Diagnose the wire harness Review all wire harness schematics If power is present review the next step Coils are receiving power Verify coils are magnetizing Position a screwdriver inside of the coil When the respective function is activated the screwdriver is drawn to the side of the coil If the coil is not drawn to the screwdriver replace the If power is present review the next step Solenoid cartridge may be contaminated or damaged A bent cartridge will not allow the valve to move freely inside of the cartridge Review all probable causes above 28 Determine a damaged cartridge valve by reversing the driver side and passenger side cartridge valves Replace valve if necessary NOTE Verify coils S3 and S4 for angle functions June 15 2010 MOLDBOARD amp WING PARTS ALL MODELS 861155 Description B52074 Moldboard B52085 Moldboard 59900 Label Information Warning B63160 Decal Center Moldboard 44833 Label Skid Steer Mounting amp Dismounting B61292 Cutting Edge Moldboard 1080 B52139 Cutting Edge Moldboard 1080 B61196 1 2 13 x 1 1 2 Carriage Bolt G8 80238 5 8 11 x 2 Carriage Bolt G8 B61365 1 2 13 Flanged Locknut B6
35. s both sides Lit No B64091 Rev 09 26 June 15 2010 TECHNICAL SPECIFICATIONS 8 CENTER OF GRAVITY INFORMATION Part Specification 810SS 8611SS Length Thickness Height Moldboard Reinforcement Cutting Edge Finish Trip Mechanism Length Thickness Height Reinforcement Cutting Edge Finish Construction Manifold Valves Angle Cylinders Stroke Ram Diameter Bore Diameter Slide Box Cylinders Cylinders Stroke Ram Diameter Bore Diameter Weight Compact Width WIDE PASS Width Snowplow BUCKET BLADE Width 96 8 12 ga 31 4 Ribs 1 2 x 6 Powder C 4 3 8 Hooked Extension 12 11 ga 31 102 8 6 11 ga 34 Q 1 4 5 8 x 6 oat White 6 3 8 Hooked Extension 23 7ga 34 1 Rib 1 4 1 4 x 10 T1 Powder C 3 8 x 12 1 2 T1 oat White 1 4 and 5 16 Mild Steel 1 4 Mild Steel w Non Skid Texture Powder Coat Black Clear Anodized Aluminum Gold Anodized Aluminum Electro Hydraulic Cartridge 2 13 15 16 1 1 2 998 Ib 96 8 120 10 111 9 3 12 2 2 1 4 18 7 16 1 1 8 1 3 4 1339 Ib 102 8 6 132 11 3 118 9 10 Adjustable Plow Shoes Mount Mechanism Standard Control Station Optional Integrated Control Weight does not include hydraulic fluid 2 Heavy Duty Cast Steel Universal Attachment Plate Pistol Grip w 3 Switches Auxiliary Harness w Diodes 8611SS 1339 Ib
36. shings inner slide box and A frame latch with NLGI Grade 2 multi purpose lithium complex grease with molybdenum MPGM to maintain consistent operation Clean and paint all scratches or exposed metal with BLIZZARD touch up paint Check the hydraulic fluid level Fill with fluid to 3 4 from the top of the reservoir Do not exceed this level Never mix different types of fluid Change the hydraulic fluid as specified in your skid steer Owner s Manual Check the trip spring adjustment Properly adjusted tension will allow a sheet of paper to pass between the 3rd and 4th coils of the spring Adjust the wing spring as needed or install an optional second extension spring for increased return speed Pressure wash and dry the entire snowplow prior to storing Cover the snowplow with a tarp if stored outside This will protect your snowplow from sun fading and inclement weather which can lead to accelerated corrosion REMOVING FROM STORAGE LIFTING 1 Perform all regular maintenance To lift and move this snowplow attach chain fall grab hooks to outside pivot beam area shown Always 2 Replace the hydraulic fluid in the hydraulic system follow recommended lift warnings and procedures Prolonged storage could result in condensation See following page for snowplow weights and build up dimensions 3 Follow the mounting procedure on the Mounting and Dismounting label 4 Initiate all of the functions and test before using Lifting Point
37. so please visit www blizzardplows com to register your new POWER PLOW snowplow June 15 2010 TABLE OF CONTENTS Mii E Safety Information ori nn Vehicle Application Information Unpacking amp Inspection Torque Moldboard amp A Frame Electrical amp Hydraulic Systems General System Schematics Hydraulic Guide Electrical Electrical Schematics Control Harness Electrical Schematics Vehicle Harness Electrical Schematics Snowplow Harness Electrical Schematics Coil Harness Electrical Schematics Aux Control Harness Lit No B64091 Rev 09 21 23 Mounting 8 Dismounting Instructions 24 Testing Your 25 Maintenance ooo 26 Technical Specifications amp CG Information 27 28 Parts 29 Moldboard 8 Wing Parts All Models 29 A Frame Pivot
38. t to withstand heavy snowplow use on the roughest road surfaces and also provide added material for protection against sidewalk curb wear Mounting hardware included Lit No B64091 Rev 09 34 June 15 2010 CONTROL ACCESSORIES amp KITS ALL MODELS Accessories B61241 Rubber Snow Deflector w Hardware B52087 Rubber Snow Deflector w Hardware B62162 Auxiliary Control Harness w Diodes B61288 3 8 Wing Cutting Edges w Hardware T1 B61536 Polyurethane Moldboard and Wing Cutting Edges w Hardware B61539 Polyurethane Moldboard and Wing Cutting Edges w Hardware B61219 POWER PLOW High Performance 12 oz Spray Paint Gloss White B63073 POWER PLOW High Performance 12 oz Spray Paint Gloss Black B61277 Hardware Kit Snowplow Assy Parts B61479 Hardware Kit Snowplow Assy Parts B60454 Hydraulic Adapter Kit Incl Items B60005 2 B60007 4 B60089 2 B60272 6 B60453 1 Hydraulic Adapter Kit Incl Items B60005 2 B60089 2 B60272 10 B60456 Hydraulic Hose Kit Incl Items B60086 2 B60223 2 B60224 4 B60455 Hydraulic Hose Kit Incl Items B60086 2 B60224 6 B61430 Hardware Kit Moldboard Cutting Edge B52067 Cutting Edge Kit Moldboard w Hardware B52095 Cutting Edge Kit Moldboard w Hardware B61431 1 Hardware Kit Wing Cutting Edge B61387 Hardware Kit Wing Cutting Edge B51104 1 Kit Wing Cutting Edges w Hardware B51103 Kit Wing Cutting Edges w Hardware B60360 Combo Seal Kit Cyl B60029 B60065 B60365 Combo
39. the cab until the top edge snowplow lever receiving holes of the skid steer plate clears the receiving pocket on Attach all hydraulic hoses on the snowplow to the top edge of the snowplow attachment plate auxiliary hydraulic connections located on the skid steer Back the skid steer away slowly On some skid steer models it may be to Position the skid steer close to the snowplow and align the mount points on the skid steer plate with the snowpl si Tilt the skid steer plate forwar necessary hydraulic switch on the skid steer snowplow Connect the snowplow wire harness to either the pistol grip control or auxiary electrical connection on the steer Lit No B64091 Rev 09 WARNING CAUTION amp INSTRUCTION LABELS Become familiar with and inform users about the warning and instruction labels on the back of the blade NOTE If labels are missing or cannot be read see your sales outlet WARNING LOWER BLADE WHEN VEHICLE IS PARKED DO NOT EXCEED GVWR OR GAWR INCLUDING BLADE AND BALLAST REMOVE BLADE ASSEMBLY BEFORE PLACING VEHICLE ON HOIST READ OWNER S MANUAL BEFORE OPERATING OR SERVICING SNOWPLOW TRANSPORT SPEED SHOULD NOT EXCEED 45 MPH FURTHER REDUCE SPEED UNDER ADVERSE TRAVEL CONDITIONS PLOWING SPEED SHOULD NOT EXCEED 10 MPH SEE YOUR SALES OUTLET WEB SITE FOR SPECIFIC VEHICLE APPLICATION RECOMMENDATIONS 59900 June 15 2010 SAFETY SAFETY PRECAUTIONS A
40. trol Mount Bracket Kit Incl Items 5 8 3 8 16 x 1 1 4 Hex Cap Screw G8 3 8 Hardened Washer Mount Bracket Pistol Grip Control 3 8 16 Hex Locknut GB N NNa a a Aa a a a a G Grade SS Stainless Steel ns not shown Lit No B64091 Rev 09 33 June 15 2010 CONTROL ACCESSORIES amp KITS ALL MODELS 10 Integrate all snowplow controls into your skid 1 NT steer using an optional auxiliary control harness 12 Durable and long lasting the POWER PLOW This 7 foot braided harness connects easily to polyurethane moldboard and wing cutting edges your existing manifold harness on one end and will keep you plowing longer and safer Specially your skid steer on the other Assembly of the formulated for snow plowing applications harness wiring to your skid steer specific auxiliary BLIZZARD poly edges resist gouging provide electrical controls required Electrical connector superior wear life and effectively reduce plowing not provided with harness noise Ideal for all plowing conditions Edges are shipped with mounting hardware 13 Putting your snowplow away for the winter Have a deep scratch to cover Clean up your blade and snowplow parts with our gloss spray paints BLIZZARD touch up paint provides an excellent finish to help keep your snowplow looking its best 11 Beef up your POWER PLOW snowplow with Paint provided in 12 oz spray cans our 3 8 thick wing cutting edges These edges are buil
41. trumentation The bracket should also not interfere with any safety devices or be positioned so that the control might rotate in front of the operator Do not mount the bracket in areas prohibited by the vehicle manufacturer See the vehicle s owner s manual or service manual for details Secure the bracket with hardware provided 6 Complete the assembly by reattaching the A frame cover Align the holes in the cover with those on the A frame and secure it with 3 8 x 1 1 2 cap screws and 3 8 washers 7 After completing the mechanical and electrical installations test all snowplow and lighting functions before attempting to drive or plow June 15 2010 ELECTRICAL SCHEMATICS CONTROL HARNESS cS ES LS YS OLS 6S GS aunosuo QN 1X aNnosuo 17 i 319NV 1 annoy a e _ annoy el e O aNa1x3 1 lt aNnosuo e 1oya1 d 1 aNnouyo aloNanos anna orzusocousxr 62 payddns ai P MOVTENINId ki pay e ok T Xov18 K 4121 movie L L
Download Pdf Manuals
Related Search