Home

2008 Cadillac CTS Owner Manual

1. 3 Disconnect electrical connector from air box 4 Loosen the screw on the clamp holding the air outlet duct in place Do not pry the clamp off position the duct aside 5 Remove the rubber hose from the air cleaner housing mounting arm Position the rubber hose aside 5 22 6 Remove the three air cleaner housing cover screws 7 Pivot the air cleaner housing cover and remove the 8 Remove the air cleaner element from the air cover from the air cleaner housing cleaner housing 5 23 How to Reinstall Engine Air Cleaner Filter 1 Install the air cleaner element to the air cleaner housing Ensure that the air cleaner element perimeter seal is installed correctly to the air cleaner housing Align the air cleaner housing cover tabs to the air cleaner housing Install the air cleaner housing cover Install the air cleaner housing cover screws Install the surge tank hose to the air cleaner housing mounting arm Ensure that the hose is routed correctly Install the air cleaner outlet duct to the air cleaner housing Tighten the air cleaner outlet duct screw clamp Attach electrical connector to airbox Reinstall side cover 5 24 A CAUTION Operating the engine with the air cleaner filter off can cause you or others to be burned The air cleaner not only cleans the air it helps to stop flames if the engine backfires If it is not there and the engine backfi
2. The belt is behind the body 1 23 Q What is wrong with this m A CAUTION You can be seriously injured by a twisted belt In a crash you would not have the full width of the belt to spread impact forces If a belt is twisted make it straight so it can work properly or ask your dealer retailer to fix it a amp Q A The belt is twisted across the body 1 24 Lap Shoulder Belt All seating positions in your vehicle have a lap shoulder belt Here is how to wear a lap shoulder belt properly 1 Adjust the seat if the seat is adjustable so you can sit up straight To see how see Seats in the Index 2 Pick up the latch plate and pull the belt across you Do not let it get twisted The lap shoulder belt may lock if you pull the belt across you very quickly If this happens let the belt go back slightly to unlock it Then pull the belt across you more slowly If you ever pull the shoulder portion of a passenger belt out all the way you may engage the child 3 Push the latch plate into the buckle until it clicks restraint locking feature If this happens just let the Pull up on the latch plate to make sure it is secure belt go back all the way and start again If the belt is not long enough see Safety Belt Extender on page 1 31 Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if necessary
3. The passenger compartment air filter is located underneath the hood below the windshield wiper arm and the screen on the passenger side of the vehicle See Engine Compartment Overview on page 5 14 for more information on location 3 28 To replace the passenger compartment air filter Ay 2 Turn the ignition to ON RUN with the engine off Turn on the windshield wipers and turn them off again when the wipers are straight up on the windshield This allows access to the leaf screen The passenger compartment air filter is located under the screen Open the hood to access the engine compartment See Hood Release on page 5 13 for more information Remove the three screws that hold the screen in place and lift off the screen by lifting and sliding it toward the center of the vehicle Pull out on the two tabs located on each end of the filter cover Lift the filter cover off by pulling it straight up Remove the old filter and insert a new one See Maintenance Replacement Parts on page 6 13 for the correct part number for the filter Reverse Steps 1 through 6 to reinstall the cover Warning Lights Gages and Indicators This part describes the warning lights and gages that may be on your vehicle The pictures will help you locate them Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement Paying attention to th
4. c cceeeeeeeeeeeneeeeeneees 2 14 Removing the Flat Tire and Installing the Spare Tire ssssinrriesinieims sieran cinis saa 5 105 Removing the Spare Tire and Tools 5 104 Replacement Bulbs eeeeeeeeeeeeeeeeeeeees 5 57 Replacement Parts Maintenance 605 6 13 10 Reporting Safety Defects Canadian Government 0cceeeeeeeeeeeeeeeees 7 14 General Motors eiciceccesccdivecsssaeveeedaavevssecsivess 7 15 United States Government eeeeeeeee eee 7 14 Restraint System Check Checking the Restraint Systems 000 1 70 Replacing Restraint System Parts After a Crash sc csisesecssicceessseeces ectavaie vives 1 71 Retained Accessory Power RAP ccecce 2 34 Roadside SEVICE sieren i e EE EEE E EA E EEEE 7 6 Rocking Your Vehicle to Get it Out 4 22 Routing Engine Drive Belt cee 6 14 Running Out of Fuel sser ins iunii ninasi 2 48 Safety Belt Reminder WiQhitiss 2ivisacactestcocdieendiauesaswoardbasaced 3 32 Safety Belts Care Ol ronen dew sad daaudele teases dateciaats 5 114 How to Wear Safety Belts Properly 1 17 Lap Shoulder Belt cceseseneeeeeneeeeeneees 1 25 Safety Belt Extender cceeeeeeeeeeneeeeeees 1 31 Safety Belt Use During Pregnancy 1 30 Safety Belts Are for Everyone 1 12 Safety Warnings and Symbols 0eeeeeeeee eee iv Sc
5. For information about using tire chains on your vehicle see Tire Chains on page 5 83 4 21 Rocking Your Vehicle to Get It Out First turn the steering wheel left and right to clear the area around the front wheels Turn off any traction or stability system See Traction Control System TCS on page 4 6 and StabiliTrak System on page 4 8 Then shift back and forth between REVERSE R and a forward gear or with a manual transmission between FIRST 1 or SECOND 2 and REVERSE R spinning the wheels as little as possible To prevent transmission wear wait until the wheels stop spinning before shifting gears Release the accelerator pedal while you shift and press lightly on the accelerator pedal when the transmission is in gear By slowly spinning the wheels in the forward and reverse directions you will cause a rocking motion that could free your vehicle If that does not get your vehicle out after a few tries it might need to be towed out If your vehicle does need to be towed out see Towing Your Vehicle on page 4 27 4 22 Loading Your Vehicle It is very important to know how much weight your vehicle can carry This weight is called the vehicle capacity weight and includes the weight of all occupants cargo and all nonfactory installed options Two labels on your vehicle show how much weight it may properly carry the Tire and Loading Information label and the Certification label A CAUTION Do not load y
6. You may use Gracenote Data only by means of the intended End User functions of this application or device You agree that you will use Gracenote Data the Gracenote Software and Gracenote Servers for your own personal non commercial use only You agree not to assign copy transfer or transmit the Gracenote Software or any Gracenote Data to any third party YOU AGREE NOT TO USE OR EXPLOIT GRACENOTE DATA THE GRACENOTE SOFTWARE OR GRACENOTE SERVERS EXCEPT AS EXPRESSLY PERMITTED HEREIN You agree that your non exclusive license to use the Gracenote Data the Gracenote Software and Gracenote Servers will terminate if you violate these restrictions If your license terminates you agree to cease any and all use of the Gracenote Data the Gracenote Software and Gracenote Servers 3 94 Gracenote reserves all rights in Gracenote Data the Gracenote Software and the Gracenote Servers including all ownership rights Under no circumstances will Gracenote become liable for any payment to you for any information that you provide You agree that Gracenote Inc may enforce its rights under this Agreement against you directly in its own name The Gracenote service uses a unique identifier to track queries for statistical purposes The purpose of a randomly assigned numeric identifier is to allow the Gracenote service to count queries without knowing anything about who you are For more information see the web page for the Gracenote
7. No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Remote Door Lock This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry RKE or keyless access transmitter or when the vehicle is automatically locked using the Keyless Locking feature You will not receive feedback when locking the vehicle with the transmitter if the doors are open See Remote Keyless Entry RKE System Operation on page 2 7 Keyless Access System Operation on page 2 9 or Keyless Locking later in this section for more information Press the customization button until Remote Door Lock appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off There will be no feedback when you press the lock button on the transmitter 3 70 Lights Only The exterior lamps will flash when you press the lock button on the transmitter Horn Only The horn will sound on the second press of the lock button on the transmitter Horn amp Lights default The exterior lamps will flash when you press the lock button on the transmitter and the horn will sound when the lock button is pressed again within five seconds of the previous command No Chan
8. Speedometer and Odometer The speedometer lets you see your speed in either miles per hour mph or kilometers per hour km h The odometer shows how far your vehicle has been driven in either miles used in the United States or kilometers used in Canada If your vehicle has to have a new odometer installed the new one may read the correct mileage This is because your vehicle s computer has stored the mileage in memory While the Driver Shift Control DSC feature is active the odometer will change to show the gear range See Automatic Transmission Operation on page 2 37 for more information Trip Odometers The trip odometer can record the number of miles or kilometers traveled for up to two trips The trip odometer is part of the Driver Information Center DIC for more information see DIC Operation and Displays on page 3 48 For vehicles that have the navigation system see your Navigation System manual for more information Tachometer The tachometer displays the engine speed in revolutions per minute rpm Notice f you operate the engine with the tachometer in the shaded warning area your vehicle could be damaged and the damages would not be covered by your warranty Do not operate the engine with the tachometer in the shaded warning area 3 31 Engine Speed Limiter This feature prevents the engine from operating at too many revolutions per minute rpm When the engine s rpms are too
9. The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis However if you notice unusual tire wear or your vehicle pulling to one side or the other the alignment might need to be checked If you notice your vehicle vibrating when driving on a smooth road the tires and wheels might need to be rebalanced See your dealer retailer for proper diagnosis Wheel Replacement Replace any wheel that is bent cracked or badly rusted or corroded If wheel nuts keep coming loose the wheel wheel bolts and wheel nuts should be replaced If the wheel leaks air replace it except some aluminum wheels which can sometimes be repaired See your dealer retailer if any of these conditions exist Your dealer retailer will know the kind of wheel you need Each new wheel should have the same load carrying capacity diameter width offset and be mounted the same way as the one it replaces If you need to replace any of your wheels wheel bolts wheel nuts or Tire Pressure Monitor System TPMS sensors replace them only with new GM original equipment parts This way you will be sure to have the right wheel wheel bolts wheel nuts and TPMS sensors for your vehicle A CAUTION Using the wrong replacement wheels wheel bolts or wheel nuts on your vehicle
10. URPA operates only at speeds less than 5 mph 8 km h If you are above this speed the red light on the rear display will flash To be detected objects must be at least 10 inches 25 4 cm off the ground and below trunk level Objects must also be within 8 feet 2 5 m from your rear bumper This distance may be less during warmer or humid weather A single beep will sound the first time an object is detected between 20 inches 0 5 m and 8 feet 2 5 m away Beeping will occur for three seconds when you are closer than 1 foot 0 3 m from the object 2 52 The following describes what will occur with the URPA display as you get closer to a detected object Description English Metric amber light amber amber lights amber amber red lights amber amber red lights flashing and beep for 1 ft 0 3m three seconds The system can be disabled through the Driver Information Center DIC See Park Assist under DIC Operation and Displays on page 3 48 for more information When the System Does Not Seem to Work Properly e The driver disables the system e The parking brake pedal is depressed e The ultrasonic sensors are not clean Keep your vehicle s rear bumper free of mud dirt snow ice and slush For cleaning instructions see Washing Your Vehicle on page 5 115 A trailer was attached to your vehicle or a bicycle or an object was hanging out of your trunk during your last drive cycle the red light m
11. With ABS you can steer and brake at the same time In many emergencies steering can help you more than even the very best braking Traction Control System TCS Your vehicle has a Traction Control System TCS that limits wheel spin This is especially useful in slippery road conditions It will activate and the TCS StabiliTrak light will flash if it senses that any of the wheels are spinning or beginning to lose traction while driving When this happens the system applies the brake to the spinning wheel s and or reduces engine power to limit wheel spin The TCS StabiliTrak warning light will flash when the traction control system is limiting wheel spin You may feel or hear the system working but this is A ee This warning light will flash if there is a problem with the traction control system See Traction Control System TCS StabiliTrak Warning Light on page 3 38 and StabiliTrak System on page 4 8 When the TCS StabiliTrak warning light is on the system will not limit wheel spin Adjust your driving accordingly TCS automatically comes on whenever vehicle is started To limit wheel spin especially in slippery road conditions you should always leave the system on But the TCS should be turned off if your vehicle ever gets stuck in sand mud or snow and rocking the vehicle is required Also turn the TCS off while in deep snow or on loose gravel to assist vehicle motion at lower speeds See Rocking Your V
12. e Your name home address and home telephone number e Telephone number of your location e Location of the vehicle e Model year color and license plate number of the vehicle e Odometer reading Vehicle Identification Number VIN and delivery date of the vehicle e Description of the problem Towing and Road Service Exclusions Specifically excluded from Roadside Service coverage are towing or services for vehicles operated on a non public roadway or highway fines impound towing caused by a violation of local Municipal State Provincial or Federal law and mounting dismounting or changing of snow tires chains or other traction devices Roadside Service is not part of or included in the coverage provided by the New Vehicle Limited Warranty Cadillac and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Service program at any time without notification Scheduling Service Appointments When your vehicle requires warranty service contact your dealer retailer and request an appointment By scheduling a service appointment and advising your service consultant of your transportation needs your dealer retailer can help minimize your inconvenience If your vehicle cannot be scheduled into the service department immediately keep driving it until it can be scheduled for service unless of course the problem is safety related If it is please call your dealership retaile
13. 2 31 Appearance Care oo ce ceecceccecceeeeeeeeeeeeees 5 111 MINFOIS denien a a Ea SA 2 49 Vehicle Identification oe cece cence eee 5 120 Object Detection Systems ceeeeeeee 2 51 Electrical System oo cece ec ecc ec ec eee ee eee eee eee 5 121 OnStar System c sssusdecsedlesed ianiai 2 53 Capacities and Specifications 5 128 Universal Home Remote System _ 2 56 Maintenance Schedule 00ccceeeseeeeeeeeeees 6 1 Storage Areas ke eec ccc ecccecceececeeeeeeeeeneeees 2 61 Maintenance Schedule ooo eee eee 6 2 SUMOO velencedsesuslzceciades ceentladetaneiensutiesn clageneane 2 62 Customer Assistance Information 7 1 Instrument Panel cece eee ee 3 1 Customer Assistance and Information _ 7 2 Instrument Panel Overview _ 00 0eeeeees 3 4 Reporting Safety Defects oo eee 7 14 Climate Controls oo eecccecea cece eeeeeeen ees 3 23 Vehicle Data Recording and Privacy _ 7 16 Warning Lights Gages and Indicators _ 3 29 Indek cananan ae aar a mene 1 Driver Information Center DIC 3 47 Audio System S ooo ccc ccc ccc eeece cence ee eneenenes 3 79 DIGITAL SURROUND GENERAL MOTORS GM the GM Emblem CADILLAC the CADILLAC Crest amp Wreath and the name CTS DTS AND DTS Digital Surround are registered are registered trademarks of General Motors trademarks of Digi
14. See Airbag Readiness Light on page 3 33 for more on this including important safety information 3 35 Charging System Light This light will come on briefly when you turn on the ignition key but the engine is not running as a check to show you it is working It should go out once the engine is running If it stays on or comes on while driving there could be a problem with the charging system A charging system Driver Information Center DIC message may also appear See DIC Warnings and Messages on page 3 54 for more information This light could indicate that there are problems with a generator drive belt or that there is an electrical problem Have it checked right away If you must drive a short distance with the light on be certain to turn off all the accessories such as the radio and air conditioner 3 36 Up Shift Light Your vehicle may have an up shift light When this light comes on you should shift to the next higher gear if weather road and traffic conditions allow you to See Manual Transmission Operation on page 2 41 for more information Brake System Warning Light Your vehicle s hydraulic brake system is divided into two parts If one part is not working the other part can still work and stop you For good braking though you need both parts working well If the warning light comes on there is a brake problem Have your brake system inspected right away BRAKE T United S
15. Three chimes sound and the exit setting is not recalled if the exit button is pressed when the vehicle is not in PARK P on an automatic transmission or the parking brake is not set on a manual transmission To recall your stored exit positions when unlocking the vehicle with the transmitter or when the ignition is turned off and the driver s door is opened see DIC Vehicle Customization on page 3 68 Reclining Seatbacks If the front passenger s seat has a manual reclining seatback the lever used to operate it is located on the Manual Reclining Seatbacks outboard side of the seat A CAUTION You can lose control of the vehicle if you try to adjust a manual driver s seat while the vehicle is moving The sudden movement could startle and confuse you or make you push a pedal when you do not want to Adjust the driver s seat only when the vehicle is not moving To recline the seatback do the following 1 Lift the recline lever AN CAUTION 2 Move the seatback to the desired position then release the lever to lock the seatback in place If the seatback is not locked it could move 3 Push and pull on the seatback to make sure it forward in a sudden stop or crash That could is locked cause injury to the person sitting there Always push and pull on the seatback to be sure it is locked 1 8 To return the seatback to an upright position do the following ale Lift the lever fully without applying pr
16. Use the radio Menu Select knob to bring up the iPod Menu and select Songs Artists Albums Playlists and Audio books to play from your iPod Your iPod will charge while it is connected to your vehicle and if your vehicle is turned to ACC ACCESSORY or ON RUN It can also be left connected to your vehicle while the vehicle is turned off or removed With the vehicle turned off the iPod will automatically be powered off and will not charge or draw power from the vehicle s battery If you have an older iPod model that is not supported or do not have the special iPod connection cable you can still listen to your iPod in your vehicle by connecting it to the Auxiliary Input Jack using a standard 3 5 mm 1 8 inch stereo cable See Using the Auxiliary Input Jack earlier for more information Press the AM FM XM or HDD buttons to listen to one of these sources while an iPod is connected If a disc is inserted press the CD AUX button to listen to a CD or DVD A disc Press the CD AUX button again to start playing and controlling the connected iPod To properly dismount the iPod USB device before disconnecting from the vehicle press the button directly under the EJECT label found on the iPod playback screen Using an MP3 MP3 WMA Format The Single CD and the Six Disc CD Radio will play MP3 WMA files that were recorded on a CD R or CD RW disc The HDD Radio is similar and can also play MP3 WMA files recorded on DVD R discs
17. e Check the distance You may be too far from your vehicle You may need to stand closer during rainy or snowy weather e Check the location Other vehicles or objects may be blocking the signal Take a few steps to the left or right hold the transmitter higher and try again e Check to determine if battery replacement is necessary See Battery Replacement later in this section e If you are still having trouble see your dealer retailer or a qualified technician for service Keyless Access System Your vehicle may have a Keyless Access System that operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment If you ever notice a decrease in the keyless access transmitter range try doing on
18. e The vehicle s battery voltage is low The battery voltage must be above 10 volts for the keyless access transmitter to be detected properly Electronic Key Not Detected Restart Allowed If your vehicle has the keyless access system this message displays when the keyless access transmitter is not detected inside the vehicle while you are trying to turn the ignition off Your vehicle may be near a strong radio antenna signal causing the keyless access system to be jammed The vehicle will remain in ACC ACCESSORY until the vehicle is turned off or is started or five minutes has expired If you turn the ignition off and you cannot find the keyless access transmitter you will not be able to restart the vehicle The keyless access transmitter needs to be inside of the vehicle in order for the vehicle to start See Starting the Engine on page 2 34 for more information Engine Hot A C Air Conditioning Off This message displays when the engine coolant becomes hotter than the normal operating temperature See Engine Coolant Temperature Gage on page 3 39 To avoid added strain on a hot engine the air conditioning compressor automatically turns off When the coolant temperature returns to normal the air conditioning compressor turns back on You can continue to drive your vehicle If this message continues to appear have the system repaired by your dealer retailer as soon as possible to avoid damage to the engine Engine Oil Lo
19. for more information 3 Pull forward on the trunk release handle to open the trunk lid On vehicles with a split folding rear seat 1 Fold down the rear seatback See Split Folding Rear Seat on page 1 11 for more information 2 Reach upward through the opening to locate the trunk release handle 3 Pull forward on the trunk release handle to open the trunk lid 2 21 a t Close the trunk by pulling on the handle Do not use the handle as a tie down Rear Seat Pass Through If your vehicle has the rear seat pass through door you can access the trunk without opening the trunk lid This is especially useful when transporting long items To open the door pull down the rear seat armrest Then pull the lever all the way down to release the door To close the door push it up and back into place Then try to open the door without pulling up on the lever to make sure it is locked into place 2 22 Emergency Trunk Release Handle Notice Do not use the emergency trunk release handle as a tie down or anchor point when securing items in the trunk as it could damage the handle The emergency trunk release handle is only intended to aid a person trapped in a latched trunk enabling them to open the trunk from the inside There is a glow in the dark emergency trunk release handle located on the back wall of the trunk This handle will glow following exposure to light Pull the release handle toward the front o
20. of time 5 44 Jump Starting If your vehicle s battery has run down you may want to use another vehicle and some jumper cables to start your vehicle Be sure to use the following steps to do it safely A CAUTION Batteries can hurt you They can be dangerous because They contain acid that can burn you They contain gas that can explode or ignite They contain enough electricity to burn you If you do not follow these steps exactly some or all of these things can hurt you Notice Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty Trying to start your vehicle by pushing or pulling it will not work and it could damage your vehicle 1 Check the other vehicle It must have a 12 volt battery with a negative ground system Notice If the other vehicle s system is not a 12 volt system with a negative ground both vehicles can be damaged Only use vehicles with 12 volt systems with negative grounds to jump start your vehicle 2 Get the vehicles close enough so the jumper cables can reach but be sure the vehicles are not touching each other If they are it could cause a ground connection you do not want You would not be able to start your vehicle and the bad grounding could damage the electrical systems To avoid the possibility of the vehicles rolling set the parking brake firmly on both vehicles involved in the jump start procedure Put an auto
21. or bugs from the windshield The button is located on the climate control system panel Push the heated washer fluid button to begin four heated wipe cycles Heating Washer Fluid Wash Wipes Pending displays on the DIC See DIC Warnings and Messages on page 3 54 The first heated wipe cycle can take up to 40 seconds to occur depending on the outside temperature After the first wipe cycle it can take up to 20 seconds for each of the remaining cycles Press the button again to turn off the heated windshield washer fluid system Heated Washer Fluid System Off displays on the DIC See DIC Warnings and Messages on page 3 54 It automatically turns off after four wipe cycles have been completed When the heated windshield washer fluid system is activated under certain outside temperature conditions steam might flow out of the washer nozzles for a short period of time before washer fluid is sprayed This is a normal condition Washer Fluid Low Add Fluid displays on the DIC when the washer fluid is low See DIC Warnings and Messages on page 3 54 Headlamp Washer Your vehicle may have headlamp washers The headlamp washers clear debris from the headlamp lenses The headlamp washers are located beneath the headlamps Press the washer button located at the end of the windshield wiper lever to wash the headlamps Both the headlamps and the windshield will be washed After the first wash the headlamps will not be washe
22. Also see Inflation Tire Pressure on page 5 67 Your vehicle s TPMS can warn you about a low tire pressure condition but it does not replace normal tire maintenance See Tire Inspection and Rotation on page 5 75 and Tires on page 5 59 Notice Using non approved tire sealants could damage the Tire Pressure Monitor System TPMS sensors TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty Always use the GM approved tire sealant available through your dealer retailer Your vehicle when new may have included a factory installed Tire Sealant and Compressor Kit This kit uses a GM approved liquid tire sealant See Tire Sealant and Compressor Kit With Sealant Selector Switch on page 5 85 or Tire Sealant and Compressor Kit Without Sealant Selector Switch on page 5 93 TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable When the system detects a malfunction the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle A DIC warning message is also displayed The low tire warning light and DIC warning message come on at each ignition cycle until the problem is corrected Some of the conditions that can cause the malfunction light and DIC message to come on are e One of the road tires has been replaced with the spare tire The spare tire does not hav
23. Headlamp High Low Beam Changer on page 3 8 Flash To Pass Feature See Flash to Pass on page 3 9 40 Fog Lamps See Fog Lamps on page 3 18 Turn and Lane Change Signals To signal a turn move the lever all the way up or down The lever returns automatically when the turn is complete An arrow on the instrument panel cluster flashes in the direction of the turn or lane change Raise or lower the lever until the arrow starts to flash to signal a lane change Hold it briefly until the lane change is complete The arrow will automatically flash three times The lever returns to its original position when it is released Rapid flashing of arrows when signaling for a turn or lane change can be caused by a burned out signal bulb Other drivers will not see the signal Replace burned out bulbs to help avoid possible accidents Check the fuse for burned out bulbs if the arrow fails to work when signaling a turn See Fuses and Circuit Breakers on page 5 122 for more information Turn Signal On Chime If the turn signal is left on for about 1 mile 1 6 km a warning chime will sound and the TURN SIGNAL ON message will appear on the Driver Information Center DIC display See Turn Signal On under DIC Warnings and Messages on page 3 54 for more information Headlamp High Low Beam Changer Push forward on the turn signal multifunction lever to change the headlamps from low to high beam Pull the lever back and then release
24. Lower the vehicle by turning the wheel wrench counterclockwise Lower the jack completely A CAUTION Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off This could lead to a crash If you have to replace them be sure to get new original equipment wheel nuts Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification See Capacities and Specifications on page 5 128 for wheel nut torque specification Notice Improperly tightened wheel nuts can lead to brake pulsation and rotor damage To avoid expensive brake repairs evenly tighten the wheel nuts in the proper sequence and to the proper torque specification See Capacities and Specifications on page 5 128 for the wheel nut torque specification 15 Tighten the wheel nuts firmly in a crisscross sequence as shown a OO 5 109 Storing a Flat or Spare Tire Use the following diagram as a guide for storing the compact spare tire in the trunk and Tools A CAUTION Storing a jack a tire or other equipment in the passenger compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store all these in the proper place After you have put the compact spare tire on your vehicle you will need to store the flat tire in your trunk The compact spare is for temporary use only Replace
25. Pull a trailer only if you have followed all the steps in this section Ask your dealer retailer for advice and information about towing a trailer with your vehicle Your vehicle can tow a trailer if it is equipped with the proper trailer towing equipment To identify the trailering capacity of your vehicle you should read the information in Weight of the Trailer that appears later in this section Trailering is different than just driving your vehicle by itself Trailering means changes in handling acceleration braking durability and fuel economy Successful safe trailering takes correct equipment and it has to be used properly 4 29 That is the reason for this part In it are many time tested important trailering tips and safety rules Many of these are important for your safety and that of your passengers So please read this section carefully before you pull a trailer Load pulling components such as the engine transmission wheel assemblies and tires are forced to work harder against the drag of the added weight The engine is required to operate at relatively higher speeds and under greater loads generating extra heat Also the trailer adds considerably to wind resistance increasing the pulling requirements If You Do Decide To Pull A Trailer If you do here are some important points e There are many different laws including speed limit restrictions having to do with trailering Make sure your rig w
26. Settings Press V To Exit appears on the DIC display See Feature Settings Exit below for more information Feature Settings Exit This feature allows you to exit the feature settings menu Press the customization button until Feature Settings Press V To Exit appears in the DIC display Press the set reset button once to exit the menu If you do not exit pressing the customization button again will return you to the beginning of the feature settings menu Advanced Features Menu Items Keyless Locking If your vehicle has the keyless access system this feature allows you to select whether the doors automatically lock during normal vehicle exit When the ignition is turned off and all doors become closed the vehicle will determine how many keyless access transmitters remain in the vehicle interior If at least one keyless access transmitter has been removed from the interior of the vehicle the doors will lock after several seconds 3 73 For example if there are two keyless access transmitters in the vehicle and one is removed the other will be locked in The keyless access transmitter locked in the vehicle can still be used to start the vehicle or unlock the doors if needed A person approaching the outside of the locked vehicle without an authorized keyless access transmitter however will not be able to open the door even with a transmitter in the vehicle See Keyless Access System Operation on page 2 9 for more inf
27. To help prevent injury to people and damage to your vehicle attach only one child restraint per anchor A CAUTION Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten Secure any unused safety belts behind the child restraint so children cannot reach them Pull the shoulder belt all the way out of the retractor to set the lock if your vehicle has one after the child restraint has been installed Be sure to follow the instructions of the child restraint manufacturer Notice Contact between the child restraint LATCH attachment parts and the vehicle s safety belt assembly may cause damage to these parts Make sure when securing unused safety belts behind the child restraint that there is no contact between the child restraint LATCH attachment parts and the vehicle s safety belt assembly Folding an empty rear seat with the safety belts secured may cause damage to the safety belt or the seat When removing the child restraint always remember to return the safety belts to their normal stowed position before folding the rear seat 1 Attach and tighten the lower attachments to the lower anchors If the child restraint does not have lower attachments or the desired seating position does not have lower anchors secure the child restraint with the top tether and the safety belts Refer to your child restraint manufacturer instructions and t
28. Used oil can be a threat to the environment If you change your own oil be sure to drain all the oil from the filter before disposal Never dispose of oil by putting it in the trash pouring it on the ground into sewers or into streams or bodies of water Instead recycle it by taking it to a place that collects used oil If you have a problem properly disposing of used oil ask your dealer retailer a service station or a local recycling center for help Engine Air Cleaner Filter The engine air cleaner filter is in the engine compartment on the driver s side of the vehicle near the front See Engine Compartment Overview on page 5 14 for more information on location When to Inspect the Engine Air Cleaner Filter Inspect the air cleaner filter at the Maintenance II intervals and replace it at the first oil change after each 50 000 mile 80 000 km interval See Scheduled Maintenance on page 6 4 for more information If you are driving in dusty dirty conditions inspect the filter at each engine oil change How to Inspect the Engine Air Cleaner Filter To inspect the air cleaner filter remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt If the filter remains caked with dirt a new filter is required To inspect or replace the engine air cleaner filter do the following 1 Turn the ignition off 2 Remove side cover by pulling up on front of cover 5 21
29. Wait until there is no sign of steam or coolant before you open the hood If you keep driving when the vehicles engine is overheated the liquids in it can catch fire You or others could be badly burned Stop your engine if it overheats and get out of the vehicle until the engine is cool See Overheated Engine Protection Operating Mode on page 5 32 for information on driving to a safe place in an emergency Notice If your engine catches fire because you keep driving with no coolant your vehicle can be badly damaged The costly repairs would not be covered by your warranty See Overheated Engine Protection Operating Mode on page 5 32 for information on driving to a safe place in an emergency If No Steam Is Coming From Your Engine An Engine Overheated Idle Engine warning along with low coolant can indicate a serious problem If you get an Engine Overheated Idle Engine warning but see or hear no steam the problem may not be too serious Sometimes the engine can get a little too hot when you e Climb a long hill on a hot day e Stop after high speed driving e Idle for long periods in traffic e Tow a trailer 5 31 If you get the Engine Overheated Idle Engine warning with no sign of steam try this for a minute or so 1 In heavy traffic let the engine idle in NEUTRAL N while stopped If it is safe to do so pull off the road shift to PARK P or NEUTRAL N and let the engine idle 2 Set the climate
30. in the tread area of the tire see Tire Sealant and Compressor Kit With Sealant Selector Switch on page 5 85 or Tire Sealant and Compressor Kit Without Sealant Selector Switch on page 5 93 Tire Sealant and Compressor Kit With Sealant Selector Switch Your vehicle has a tire sealant and compressor kit that is capable of temporarily sealing a puncture up to Ya inch 6mm in the tread area of the tire There is no jack or spare tire The kit inflates the tire with liquid sealant and air The tire sealant and compressor kit can also be used to inflate an underinflated tire After the tire is inflated to the recommended inflation pressure see Inflation Tire Pressure on page 5 67 for more information the vehicle must be driven for five miles to distribute the sealant in the tire and seal the puncture After driving five miles the tire pressure must be rechecked and adjusted as needed See Using the Tire Sealant and Compressor Kit to Temporarily Seal a Punctured Tire later in this section Be sure to read and follow all of the tire sealant and compressor kit instructions The kit includes Selector Switch On Off Button Air Pressure Gage Tire Sealant Canister E Air Compressor Accessory Plug F Sealant Air Hose Clear G Air Only Hose After temporarily sealing the tire sealant and compressor kit it is recommended to take your vehicle to an authorized dealer retailer as soon as possible If
31. inflate the tire to its recommended pressure Do not exceed 36 psi 248 kPa 8 Turn the selector switch A counterclockwise to the sealant and air position 9 Push the On Off button B The sealant and compressor kit will inject sealant and air into the tire Sealant may leak from the puncture until the vehicle is driven and the hole has sealed The pressure gage C will initially show a high pressure while the compressor pushes the sealant into the tire Once the sealant is completely dispersed into the tire the pressure will quickly drop and start to rise again as the tire inflates with air 5 88 10 Inflate the tire to the recommended inflation pressure found on the Tire and Loading Information label See Inflation Tire Pressure on page 5 67 The pressure gage reads high while the compressor is running Turn the compressor off to get an accurate pressure reading Notice If the recommended pressure cannot be reached after 15 minutes the vehicle should not be driven farther Damage to the tire is severe and the sealant will not be effective Remove the air compressor plug from the accessory power outlet and unscrew the inflating hose from the tire valve See Roadside Service on page 7 6 11 Turn the compressor off by pushing the On Off button B 12 The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire Steps 11 through 18 must be done
32. oreson enron r saved 3 22 Audio SyStEm oscscepcesaceiedasocerteaciotanmceatiberagecite 3 79 Audio Steering Wheel Controls 0 3 106 Backglass Antenna c ceceeeeeeeeeenee eee ees 3 108 Navigation Radio System see Navigation Manual niscciiertcenenciadatlads inaeknliotaicnaipeans 3 106 Radio Reception nccrne een nn ANE 3 107 Theft Deterrent Feature 2 3 106 XM Satellite Radio Antenna System 3 108 Audio System S cceceeeseeeeeneeeeeeeeaeeaeeaeeaees 3 80 Automatic Transmission FUG E E S 5 25 Operation cicera einai 2 37 Backglass Antenna eceeeeeeeeeeeeeeeeeeeeees 3 108 Battery x iccdicsedehaceitas cant trna E a 5 43 Electric Power Management asasen 3 20 Exterior Lighting Battery Saver 005 3 19 Run Down Protection ccceeeeeeeeeeeeeeeees 3 21 Brake Emergencies posken aeeie 4 5 BiakoS oraire es a a EEE 5 40 Panc ASSIST opira e r e 4 9 System Warning Light a an 3 37 B aking ors siis despa e nE E E 4 3 Braking in Emergencies seeeeeeeeeeeeeeeenees 4 5 Break In New Vehicle cccccceeeeeeeeeeenes 2 31 Bulb Replacement eceeeeeeeeeceeeeeeeeeeeees 5 55 Front Turn Signal and Fog Lamps 5 56 Halogen Bulbs ssacicsied eevettetuerreetecenni tiers 5 55 Headlamp AiMing eceeeeeeeeeeeteeen teeta ees 5 51 High Intensity Discharge HID Lighting 5 55 License Plate La
33. the appropriate safety equipment and training The jack provided with your vehicle is designed only for changing a flat tire If it is used for anything else you or others could be badly injured or killed if the vehicle slips off the jack Use the jack provided with your vehicle only for changing a flat tire Tire Sealant and Compressor Kit If your vehicle has a factory installed tire sealant and compressor kit there is no spare tire no tire changing equipment and no place to store a tire 5 84 If a tire goes flat avoid further tire and wheel damage by driving slowly to a level place and stopping 1 Turn on the hazard warning flashers See Hazard Warning Flashers on page 3 6 2 Park your vehicle If your vehicle has an automatic transmission set the parking brake firmly and put the shift lever in PARK P See Shifting Into PARK P Automatic Transmission on page 2 44 If your vehicle has a manual transmission move the shift lever to REVERSE R and set the parking brake firmly See Parking Your Vehicle Manual Transmission on page 2 46 for additional information 3 Turn off the engine 4 Inspect the flat tire If the tire has been separated from the wheel has damaged sidewalls or has a puncture larger than a 1 4 inch 6 mm the tire is too severely damaged for the tire sealant and compressor kit to be effective See Roadside Service on page 7 6 If the tire has a puncture less than a 1 4 inch 6 mm
34. while driving If you become tired or sleepy find a safe place to park your vehicle and rest Other driving tips include e Keep the vehicle well ventilated e Keep interior temperature cool e Keep your eyes moving scan the road ahead and to the sides e Check the rearview mirror and vehicle instruments often Hill and Mountain Roads Driving on steep hills or through mountains is different AN CAUTION than driving on flat or rolling terrain Tips for driving in these conditions include Coasting downhill in NEUTRAL N or with the e Keep your vehicle serviced and in good shape ignition off is dangerous The brakes will have e Check all fluid levels and brakes tires cooling to do all the work OF slowing down and they system and transmission could get so hot that they would not work well You would then have poor braking or even Going down steep or long hills shift to a none going down a hill You could crash lower gear Always have the engine running and your vehicle in gear when you go downhill A CAUTION e Stay in your own lane Do not swing wide or cut across the center of the road Drive at speeds that let you stay in your own lane would then have poor braking or even none e Top of hills Be alert something could be in your going down a hill You could crash Shift down lane stalled car accident to let the engine assist the brakes on a steep e Pay attention to special road signs fall
35. 34 Air Conditioning Press this button to override the automatic system and turn the air conditioning system on or off When in AUTO the air conditioning compressor will come on automatically as necessary The air conditioning system removes moisture from the air so a small amount of water might drip underneath the vehicle while idling or after turning off the engine This is normal amp Recirculation Outside Air Press this button to switch between recirculation and outside air Whenever the button is pressed the indicator light comes on for the mode being used The recirculation mode recirculates air inside the vehicle It can be used to prevent outside air and odors from entering the vehicle or to help cool the air inside the vehicle more quickly Press the auto button to have the system select the best air delivery mode for your temperature setting Recirculation is not available in the defrost mode and automatically turns off 10 minutes after defog is selected This helps to limit window fogging in the vehicle Using recirculation for long periods of time could cause the air inside the vehicle to become too dry or stuffy To prevent this from happening after the air in the vehicle has cooled select outside air or press the auto button The outside air mode pulls fresh air from outside the vehicle Outside air is always selected in defrost mode to prevent fogging tv Heated Windshield Washer If Equipped For mo
36. 4 If equipped with a shoulder belt height adjuster move it to the height that is right for you Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash See Shoulder Belt Height Adjustment later in this section 1 25 5 To make the lap part tight pull up on the shoulder belt It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants 1 26 To unlatch the belt just push the button on the buckle The belt should go back out of the way Before you close a door be sure the belt is out of the way If you slam the door on it you can damage both the belt and your vehicle Shoulder Belt Height Adjuster Your vehicle has a shoulder belt height adjuster for the driver and right front passenger position Adjust the height so that the shoulder portion of the belt is centered on your shoulder The belt should be away from your face and neck but not falling off your shoulder Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash To move it down press the release button A and move the height adjuster to the desired position You can move the height adjuster up just by pushing up on the shoulder belt guide After you move the height adjuster to where you want it try to move it down without pressing the release button to make sure it has lo
37. 800 496 9992 English 1 800 496 9993 Spanish Fax Number 313 381 0022 From U S Virgin Islands 1 800 496 9994 Fax Number 313 381 0022 Canada Customer Assistance General Motors of Canada Limited Canadian Cadillac Customer Communication Centre CA1 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 www gmcanada com 1 888 446 2000 1 800 263 3830 For Text Telephone devices TTYs Roadside Assistance 1 800 882 1112 Overseas Customer Assistance Please contact the local General Motors Business Unit Mexico Central America and Caribbean Islands Countries Except Puerto Rico and U S Virgin Islands Customer Assistance General Motors de Mexico S de R L de C V Customer Assistance Center Paseo de la Reforma 2740 Col Lomas de Bezares C P 11910 Mexico D F 01 800 508 0000 Long Distance 011 52 53 29 0 800 GM Mobility Reimbursement Program E MOBILITY This program available to qualified applicants can reimburse you up to 1 000 of the cost of eligible aftermarket adaptive equipment required for your vehicle such as hand controls or a wheelchair scooter lift 7 6 The offer is available for a very limited period of time from the date of vehicle purchase lease For more details or to determine your vehicle s eligibility visit gmmobility com or call the GM Mobility Assistance Center at 1 800 323 9935 Text telephone TTY users call 1 800 833 9935 General Motors of Ca
38. Branch 2780 Sheffield Road Ottawa Ontario K1B 3V9 Reporting Safety Defects to General Motors In addition to notifying NHTSA or Transport Canada in a situation like this please notify General Motors Call 1 800 458 8006 or write Cadillac Customer Assistance Center Cadillac Motor Car Division P O Box 33169 Detroit MI 48232 5169 In Canada call 1 888 446 2000 or write Canadian Cadillac Customer Communication Centre CA1 163 005 General Motors of Canada Limited 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines transmission axle suspension brakes electrical steering body etc Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks Each bulletin contains instructions to assist in the diagnosis and service of your vehicle Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle The owner manual includes the Maintenance Schedule for all models In Portfolio Includes a Portfolio Owner Manual and Warranty Booklet RETAIL SELL PRICE 35 00 U S plus processing fee Without Portfolio Owner Manual only RETAIL SELL PRICE 25 00 U S plus processing fee Current and Past Model Order Form
39. DIC display the compass should be calibrated If the DIC display does not show a heading for example N for North or the heading does not change after making turns there may be a strong magnetic field interfering with the compass Such interference may be caused by a magnetic CB or cell phone antenna mount a magnetic emergency light magnetic note pad holder or any other magnetic item Turn off the vehicle move the magnetic item then turn on the vehicle and calibrate the compass 3 53 To calibrate the compass use the following procedure Compass Calibration Procedure 1 Before calibrating the compass make sure the compass zone is set to the variance zone in which the vehicle is located See Compass Variance Zone Procedure earlier in this section Do not operate any switches such as window sunroof climate controls seats etc during the calibration procedure 2 Press the vehicle information button until Press V To Calibrate Compass displays 3 Press the set reset button to start the compass calibration 4 The DIC will display Calibrating Drive In Circles Drive the vehicle in tight circles at less than 5 mph 8 km h to complete the calibration The DIC will display Calibration Complete for a few seconds when the calibration is complete The DIC display will then return to Press To Calibrate Compass 3 54 DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that th
40. Flashers on page 3 6 Audio Base Audio System or Audio Navigation System If Equipped See Audio System s on page 3 79 or Navigation Radio System on page 3 106 Parking Brake Release See Parking Brake on page 2 43 L M N Hood Release See Hood Release on page 5 13 Cruise Control Buttons See Cruise Control on page 3 13 Tilt Wheel Lever See Tilt and Telescopic Steering Wheel on page 3 6 or Power Tilt Wheel and Telescopic Steering Column on page 3 7 Horn See Horn on page 3 6 Audio Steering Wheel Controls See Audio Steering Wheel Controls on page 3 106 Heated and Ventilated Seats See Heated and Ventilated Seats on page 1 6 Dual Climate Control System See Dual Climate Control System on page 3 23 Shift Lever See Automatic Transmission Operation on page 2 37 or Manual Transmission Operation on page 2 41 Storage Compartment See Instrument Panel Storage on page 2 61 Accessory Power Outlet See Accessory Power Outlet s on page 3 21 Glove Box See Glove Box on page 2 61 Hazard Warning Flashers The hazard warning flashers let you warn the police and others that you have a problem The front and rear turn signal lamps will flash on and off The hazard warning flasher button is on the instrument panel Press the button to make the front and rear turn signal lamps flash on and off Press again to turn the flashers completely off The hazard warning flashers work ev
41. Flat or Spare Tire and Tools 5 110 Tire Sealant and Compressor Kit 5 85 5 93 Tire Sidewall Labeling ceeeeseeeeeeeee ees 5 61 Tire Terminology and Definitions 5 64 Uniform Tire Quality Grading eeeeeeee 5 80 Wheel Alignment and Tire Balance 5 81 Wheel Replacement 0 cseeeceeeeeeeeeeeees 5 81 When It Is Time for New Tires 0 eeee 5 76 Winter THOS ss ttesciertnctaeecdess osu dendinedgentabead 5 60 Towing Recreational Vehicle eeceeeeeneeeeeee eens 4 27 Towing a Waller sersrrotanteee no e E 4 29 NOU VeNICIE osrand a a 4 27 Traction Control System TCS smissiiniaisi sarni rai 4 6 Control System TCS StabiliTrak Warning e ai E E E T 3 38 Limited Slip Rear Axle a se 4 8 StabiliTrak System ccccccceeeeseeeeeeeeeeeenees 4 8 Transmission Fluid Automatic ccc eee ec esc eeeeeeeeeeneeenees 5 25 FIUIG IMANUAl scccccciswsccaccsaesdacesaancaasevevstacsaeecs 5 25 Up Shit LIJN ssccs ctecractcetiagaatsnianaeeneeeenataten 3 36 Transmission Operation Automatic 6 2 37 Transmission Operation Manual 066 2 41 Trip Odometers ccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 3 31 TUAR oiean ssn ec E AE 2 20 Turn and Lane Change Signals 0 ceseeeees 3 8 Turn Signal Multifunction Lever ceeeeeeeeeee ee 3 7 Ultrasonic Rear Parking Assist UR
42. GVWR or either the maximum front or rear Gross Axle Weight Rating GAWR If you do parts on your vehicle can break and it can change the way your vehicle handles These could cause you to lose control and crash Also overloading can shorten the life of your vehicle Notice Overloading your vehicle may cause damage Repairs would not be covered by your warranty Do not overload your vehicle If you put things inside your vehicle like suitcases tools packages or anything else they will go as fast as the vehicle goes If you have to stop or turn quickly or if there is a crash they will keep going A CAUTION Things you put inside your vehicle can strike and injure people in a sudden stop or turn or in a crash Put things in the trunk of your vehicle In a trunk put them as far forward as you can Try to spread the weight evenly Never stack heavier things like suitcases inside the vehicle so that some of them are above the tops of the seats Do not leave an unsecured child restraint in your vehicle When you carry something inside the vehicle secure it whenever you can Do not leave a seat folded down unless you need to Towing Towing Your Vehicle Consult your dealer retailer or a professional towing service if you need to have your disabled vehicle towed See Roadside Service on page 7 6 If you want to tow your vehicle behind another vehicle for recreational purposes such as behind a mot
43. If an audio CD is not found in the Gracenote Database and it does not have CD text information the radio will record the audio CD with all song artist album and genre names as NO INFO Songs recorded with NO INFO to the HDD will be hard to sort identify and select For better HDD navigation CDs with NO INFO can first be converted to MP3 format with Tag information on a home computer and then recorded to the HDD from an MP3 disc or USB device Occasionally the radio may find more than one match in Gracenote Database for an audio CD that has been recorded If this happens the radio will display MultiHit for the name information when the songs are selected from the HDD With a MuliHit song playing press the button below the EDIT label to bring up the list of multiple names found in the Gracenote Database Use the Menu Select knob to highlight and select the correct name for the MultiHit recorded CD The Gracenote Database stored on your HDD can be updated so that it includes name information for more recently released audio CDs See your dealer retailer for more information on Gracenote Database updates for your HDD radio Gracenote Database Gracenote Music Recognition Service Music recognition technology and related data are provided by Gracenote Gracenote is the industry standard in music recognition technology and related content delivery For more information vi
44. Odometers cceeeeeeeeeeeeeeeeceeeeeeeeeees 3 31 TAGHOMCIGN poprie neiaa eno E enna 3 31 Engine Speed Limiter ceeeeeeeeeeeeeees 3 32 Safety Belt Reminders cceeeeeeeeeeeeeeee 3 32 Airbag Readiness Light ceeeeeeeeeee eres 3 33 Passenger Airbag Status Indicator 3 34 Charging System Light ceeeeeeeeeeeeee ee 3 36 Up Shift LIQht sic tssserds eaen e 3 36 Brake System Warning Light ceeee 3 37 3 1 Section 3 Instrument Panel Antilock Brake System Warning Light 3 38 Driver Information Center DIC 3 47 Traction Control System TCS StabiliTrak DIC Operation and Displays eeeeeeeees 3 48 Warning LIgAt ccicsnsteiseserecasats nasien 3 38 DIC COMPASS sprod niata oia E ieas 3 52 Engine Coolant Temperature Warning Light 3 39 DIC Warnings and Messages 6 seeeeeeeees 3 54 Engine Coolant Temperature Gage 6 3 39 DIC Vehicle Customization ccceeeeeeeee eee 3 68 Tire Pressure Light s seein 3 40 Audio System Ss scssecessssesesscesssesssessteeess 3 79 Malfunction Indicator Lamp 1s tees 3 40 Radio Sjene s e e eas ease see eter 3 80 Ol Pressure Light 2c cececcesssenntee8 dence et innii 3 43 Using an MP3 csicskcasscsnicssanscessanstaserascnannecses 3 101 Engine Oil Pressure Gage 3 44 XM Radio Messages c c
45. Replace Battery In Remote Key The vehicle can still be driven See Battery Replacement under Keyless Access System Operation on page 2 9 for more information Notice Do not try to shift to PARK P if your vehicle is moving If you do you could damage the transmission Shift to PARK P only when your vehicle is stopped Manual Transmission The shift lever should be in neutral position and the parking brake engaged Hold the clutch pedal down to the floor and start the engine Your vehicle will not start if the clutch pedal is not all the way down That is a safety feature Starting Procedure 1 With your foot off the accelerator pedal turn the ignition key to START If your vehicle has the keyless access system make sure there is a keyless access transmitter in the vehicle When the engine starts let go of the ignition The idle speed will go down as your engine gets warm Do not race the engine immediately after starting it Operate the engine and transmission gently to allow the oil to warm up and lubricate all moving parts Your vehicle has a Computer Controlled Cranking System This feature assists in starting the engine and protects components If the ignition key is turned to the START position and then released when the engine begins cranking the engine will continue cranking for a few seconds or until the vehicle starts If the engine does not start and the key is held in START for many seconds cranking
46. Restraint Systems Safety Belts Now and then make sure the safety belt reminder light and all your belts buckles latch plates retractors and anchorages are working properly Look for any other loose or damaged safety belt system parts If you see anything that might keep a safety belt system from doing its job have it repaired Torn or frayed safety belts may not protect you in a crash They can rip apart under impact forces If a belt is torn or frayed get a new one right away Make sure the safety belt reminder light is working See Safety Belt Reminders on page 3 32 for more information Keep safety belts clean and dry See Care of Safety Belts on page 5 114 1 70 Airbags The airbag system does not need regularly scheduled maintenance or replacement Make sure the airbag readiness light is working See Airbag Readiness Light on page 3 33 for more information Notice If an airbag covering is damaged opened or broken the airbag may not work properly Do not open or break the airbag coverings If there are any opened or broken airbag covers have the airbag covering and or airbag module replaced For the location of the airbag modules see What Makes an Airbag Inflate on page 1 62 See your dealer retailer for service Replacing Restraint System Parts After a Crash A CAUTION A crash can damage the restraint systems in your vehicle A damaged restraint system may not properly protect the person using it
47. SAE 5W 30 with the starburst symbol at all temperatures Substitute oil not meeting GM Standard GM4718M should not be used for an oil change Engine Oil Additives Do not add anything to the oil The recommended oils with the starburst symbol that meet GM standards are all you need for good performance and engine protection Engine Oil Life System When to Change Engine Oil Your vehicle has a computer system that lets you know when to change the engine oil and filter This is based on engine revolutions and engine temperature and not on mileage Based on driving conditions the mileage at which an oil change will be indicated can vary considerably For the oil life system to work properly you must reset the system every time the oil is changed When the system has calculated that oil life has been diminished it will indicate that an oil change is necessary A Change Engine Oil Soon message will come on See DIC Warnings and Messages on page 3 54 Change the oil as soon as possible within the next 600 miles 1 000 km It is possible that if you are driving under the best conditions the oil life system might not indicate that an oil change is necessary for over a year However the engine oil and filter must be changed at least once a year and at this time the system must be reset Your dealer retailer has trained service people who will perform this work using genuine parts and reset the system It is also important to check the oi
48. Should an Airbag Inflate ee 1 60 What Makes an Airbag Inflate e 1 62 Safety Belts vi eaeeeetereseenerernenesnererereneenererenentay 1 12 How Does an Airbag Restrain ccce 1 62 Safety Belts They Are for Everyone 1 12 What Will You See After an Airbag Inflates 1 62 How to Wear Safety Belts Properly 1 17 Passenger Sensing System 0c0eeeeeeees 1 64 Lap Shoulder Belt cet eeeenteneeeeneeeeeeeeeeneeeeneeeeens 1 25 Servicing Your Airbag Equipped Vehicle 1 68 Safety Belt Use During Pregnancy 0 1 30 Adding Equipment to Your Airbag Equipped Safety BEI EXIENAST accoreataseeatnisdsessoencreetneite 1 31 Vehicle inedetuts ain aectastiaide atelier oar oleae 1 69 Child Restraints cece teers tenes 1 32 Restraint System Check i 1 70 Older Children PEPER EEE 1 32 Checking the Restraint Systems c c cc 00 1 70 Infants and Young Children s2cc2eccsevecersacvevecaces 1 35 Replacing Restraint System Parts After Child Restraint Systems esr 1 39 a CraSh sedieredencautcuarnciicad Patacevlectuneiaentiadande 1 71 1 1 Head Restraints The vehicle s front seats have adjustable head restraints in the outboard seating positions The vehicle s rear seats have head restraints in the outboard seating positions but they are not adjustable A CAUTION With head restraints that are not installed and
49. The indicator light on the button turns on when cruise control is on RES Resume Accelerate Press this button to make the vehicle accelerate or resume to a previously set speed SET Set Coast Press this button to set the speed or make the vehicle decelerate 3 14 amp Cancel Press this button to cancel cruise control without erasing the set speed from memory Setting Cruise Control Cruise control will not work if the parking brake is set or if the master cylinder brake fluid level is low The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed A CAUTION If you leave your cruise control on when you are not using cruise you might hit a button and go into cruise when you do not want to You could be startled and even lose control Keep the cruise control switch off until you want to use cruise control 1 Press the cruise contro On Off button 2 Get up to the desired speed 3 Press the SET button located on the steering wheel and release it 4 Take your foot off the accelerator Resuming a Set Speed Suppose the cruise control is set at a desired speed and then the brake is applied This shuts off the cruise control But it does not need to be reset Once the vehicle is driving at about 25 mph 40 km h or more press the RES button on the steering wheel The vehicle will go back to the previous set speed and stay the
50. This may not be long enough for Universal Home Remote to pick up the signal during programming 2 60 Similarly some U S gate operators are manufactured to time out in the same manner If you live in Canada or you are having difficulty programming a gate operator or garage door opener by using the Programming Universal Home Remote procedures regardless of where you live replace Step 3 under Programming Universal Home Remote with the following Continue to press and hold the Universal Home Remote button while you press and release every two seconds cycle the hand held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote The Universal Home Remote indicator light will flash slowly at first and then rapidly Proceed with Step 4 under Programming Universal Home Remote to complete Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second The indicator light will come on while the signal is being transmitted Erasing Universal Home Remote Buttons Erase the programmed buttons when you sell or terminate your lease To erase all programmed buttons on the Universal Home Remote device 1 Press and hold down the two outside buttons until the indicator light begins to flash after 20 seconds 2 Release both buttons Reprogramming a Single Universal Home Remote Button To reprogram any of t
51. To replace one of these bulbs do the following Push tabs to remove the license plate lamp Turn the license plate lamp assembly down to remove it Turn the socket counterclockwise and remove it Pull the bulb straight out to remove it Push the new bulb straight into the socket Reverse Steps 1 through 3 to reinstall the license plate lamp assembly Replacement Bulbs Exterior Lamp Bulb Number Front Turn Signal 3157K Fog Lamp Uplevel Only H11LL License Plate Lamp W5WLL For replacement bulbs not listed here contact your dealer retailer Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking See Owner Checks and Services on page 6 8 It is a good idea to clean or replace the wiper blade assembly on a regular basis or when worn For proper windshield wiper blade length and type see Maintenance Replacement Parts on page 6 13 To replace the wiper blade assembly 1 Turn the ignition to ON RUN with the engine off 2 Turn on the windshield wipers and turn them off again when the wipers are in the out wipe position The driver side blade will be straight up and down on the windshield 3 Pull the windshield wiper assembly away from the windshield 5 57 ZL AQ Se Ze PA I 4 Lift up the wiper blade assembly cap 5 Pull the wiper blade assembly down far enough to release it from the J hooked end of the wiper arm Slide the assembly away from
52. Window Defogger under Dual Climate Control System on page 3 23 for more information Object Detection Systems Ultrasonic Rear Parking Assist URPA If your vehicle has the Ultrasonic Rear Parking Assist URPA system it helps you park easier and avoid other vehicles while in REVERSE R It operates at speeds less than 5 mph 8 km h It can determine how close objects are to the rear bumper up to 8 feet 2 5 m behind your vehicle The distance sensors are located on the rear bumper A CAUTION The Ultrasonic Rear Parking Assist URPA system does not replace driver vision It cannot detect e objects that are below the bumper underneath the vehicle or if they are too close or far from the vehicle e children pedestrians bicyclists or pets CAUTION Continued CAUTION Continued If you do not use proper care before and while backing vehicle damage injury or death could occur Even with URPA always check behind your vehicle before backing up While backing be sure to look for objects and check your vehicle s mirrors The display is located above the rear window and can be seen by looking over your right shoulder URPA uses three color coded lights to provide distance and system information 2 51 How the System Works URPA comes on automatically when the shift lever is moved into REVERSE R The rear display will then briefly illuminate to let you know the system is working
53. a l adresse suivante Helm Incorporated P O Box 07130 Detroit MI 48207 1 800 551 4123 www helminc com Using this Manual Many people read the owner manual from beginning to end when they first receive their new vehicle to learn about the vehicle s features and controls Pictures and words work together to explain things Index A good place to quickly locate information about the vehicle is the Index in the back of the manual It is an alphabetical list of what is in the manual and the page number where it can be found Safety Warnings and Symbols There are a number of safety cautions in this book A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning A CAUTION These mean there is something that could hurt you or other people We tell you what the hazard is and what to do to help avoid or reduce the hazard Please read these cautions If you do not you or others could be hurt A circle with a slash through it is a safety symbol which means Do Not Do Not do this or Do Not let this happen Vehicle Damage Warnings You will also find notices in this manual Notice These mean there is something that could damage your vehicle A notice tells about something that can damage the vehicle Many times this damage would not be covered by your vehicle s warranty and it could be costly The notice tells what to do to h
54. accidents mentioned on the news happen on curves Here is why Experienced driver or beginner each of us is subject to the same laws of physics when driving on curves The traction of the tires against the road surface makes it possible for the vehicle to change its path when you turn the front wheels If there is no traction inertia will keep the vehicle going in the same direction If you have ever tried to steer a vehicle on wet ice you will understand this The traction you can get in a curve depends on the condition of the tires and the road surface the angle at which the curve is banked and your speed While you are in a curve speed is the one factor you can control Suppose you are steering through a sharp curve Then you suddenly accelerate Both control systems steering and acceleration have to do their work where the tires meet the road Adding the sudden acceleration can demand too much of those places You can lose control See Traction Control System TCS on page 4 6 What should you do if this ever happens Ease up on the accelerator pedal steer the vehicle the way you want it to go and slow down Speed limit signs near curves warn that you should adjust your speed Of course the posted speeds are based on good weather and road conditions Under less favorable conditions you will want to go slower If you need to reduce your speed as you approach a curve do it before you enter the curve while t
55. adding water e Do not mix water with ready to use washer fluid Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system Also water does not clean as well as washer fluid e Fill the washer fluid tank only three quarters full when it is very cold This allows for fluid expansion if freezing occurs which could damage the tank if it is completely full e Do not use engine coolant antifreeze in your windshield washer It can damage the vehicle s windshield washer system and paint 5 39 Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid See Engine Compartment Overview on page 5 14 for the location of the reservoir DOT 3 AR There are only two reasons why the brake fluid level in the reservoir might go down The first is that the brake fluid goes down to an acceptable level during normal brake lining wear When new linings are put in the fluid level goes back up The other reason is that fluid is leaking out of the brake hydraulic system If it is you should have the brake hydraulic system fixed since a leak means that sooner or later the brakes will not work well 5 40 It is not a good idea to top off the brake fluid Adding brake fluid will not correct a leak If fluid is added when the linings are worn there will be too much fluid when new brake linings are installed Add or remove brake fluid as necessary onl
56. adjusted properly there is a greater chance that occupants will suffer a neck spinal injury in a crash Do not drive until the head restraints for all occupants are installed and adjusted properly 1 2 Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant s head This position reduces the chance of a neck injury in a crash Pull the head restraint up to raise it To lower the head restraint press the button located on the top of the seatback and push the restraint down 7 Push down on the head restraint after the button is released to make sure that it is locked in place The vehicle s head restraints are not designed to be removed Active Head Restraint System On vehicles with an active head restraint system in the front outboard seating positions These automatically tilt forward to reduce the risk of neck injury if the vehicle is hit from behind Front Seats Manual Seats A CAUTION You can lose control of the vehicle if you try to adjust a manual driver s seat while the vehicle is moving The sudden movement could startle and confuse you or make you push a pedal when you do not want to Adjust the driver s seat only when the vehicle is not moving To move a manual seat forward or rearward 1 Lift the bar to unlock the seat 2 Slide the seat to the desired position and release the bar Try to move the seat with
57. after 10 minutes unless a time extension has been done To manually shut off a remote start e Aim the transmitter at the vehicle and press the remote start button until the parking lamps turn off e Turn on the hazard warning flashers e Turn the ignition switch on and then off The remote vehicle start feature provides two separate starts each with 10 minutes of engine running or it provides one start with 10 minutes of engine running that may be extended 10 more minutes If you press and release the transmitter lock button and then press and hold the remote start button on the transmitter again before the first 10 minutes of engine running time has expired 10 minutes are added to the remaining minutes For example if the lock button and then the remote start buttons are pressed again after five minutes of the engine run time 10 minutes are added and you now have 15 minutes of engine running The added ten minutes are considered a second remote vehicle start Once two remote starts or a single start with a time extension have been used the vehicle must be started with the keyless access ignition control knob before you can use the remote start feature again The remote start feature will not operate if any of the following occur e The ignition is in any position other than LOCK OFF e A keyless access transmitter is inside the vehicle e The hood is open e There is an emission control system malfunction e The rem
58. and sand crews can get there Whatever the condition smooth ice packed blowing or loose snow drive with caution The Traction Control System TCS improves your ability to accelerate when driving on a slippery road Even though you have TCS slow down and adjust your driving to the road conditions Under certain conditions you might want to turn the TCS off such as when driving through deep snow and loose gravel to help maintain vehicle motion at lower speeds See Traction Control System TCS on page 4 6 Also see StabiliTrak System on page 4 8 If Your Vehicle is Stuck in Sand Mud Ice or Snow on page 4 21 and Winter Tires under Tires on page 5 59 The Antilock Brake System ABS improves your vehicle s stability when you make a hard stop ona slippery road Even though you have ABS begin stopping sooner than you would on dry pavement See Antilock Brake System ABS on page 4 4 e Allow greater following distance on any slippery road e Watch for slippery spots The road might be fine until you hit a spot that is covered with ice On an otherwise clear road ice patches can appear in shaded areas where the sun cannot reach such as around clumps of trees behind buildings or under bridges Sometimes the surface of a curve or an overpass can remain icy when the surrounding roads are clear If you see a patch of ice ahead of you brake before you are on it Try not to brake while you are actually on the
59. brake For the base ignition turn the ignition key to OFF LOCK press the release button and remove the key See Key Release Button under gnition Positions Key Access on page 2 31 or Ignition Positions Keyless Access on page 2 33 for more information For the keyless access ignition turn the ignition to LOCK OFF and remove the keyless access transmitter If you are towing a trailer see Towing a Trailer on page 4 29 Parking Over Things That Burn A CAUTION CAUTION Continued You might have exhaust coming in if Things that can burn could touch hot exhaust parts under your vehicle and ignite Do not park over papers leaves dry grass or other things that can burn Engine Exhaust A CAUTION Engine exhaust can kill It contains the gas carbon monoxide CO which you cannot see or smell It can cause unconsciousness and death CAUTION Continued The exhaust system sounds strange or different Your vehicle gets rusty underneath Your vehicle was damaged in a collision Your vehicle was damaged when driving over high points on the road or over road debris Repairs were not done correctly Your vehicle or the exhaust system has been modified improperly If you ever suspect exhaust is coming into your vehicle e Drive it only with all the windows down to blow out any CO and e Have your vehicle fixed immediately 2 47 Running the Vehicle While Parked It is better not to park w
60. c icscckedicseedser cee ecce tensor voneke 3 21 Outside Convex Mirror cccececeecece sence sense eeeeeeeeees 2 50 Heated Minors seiss civics seas ae aria ea 2 50 Power Mirrors 2 0ceceeeeeeeeeeeeeeeeeeeeeeeees 2 49 Overheated Engine Protection Operating Mode 5 32 Owner Checks and Services 0cesceeeeeeee es 6 8 Owners Canadian ccccccecec eee eeseeeeeeeeeeeeaeees iii Paint DAMJE essiri ainnise 5 118 Panic Brake ASSISt eniinn cape n 4 9 Parade DIMMING sisi ciscsccmiesscsccacieds iani 3 19 Pan AIG erener naaa E aree R EE 2 51 Park Brake wssscccesicess csvave ncryeeesadeeersn nE Er 2 43 Park P SANNO INTO Taraire neoe 2 44 Shifting QUT O diririiasest an a eed 2 45 Park Tilt MURMOMrs recie osica iaee 2 50 Parking ASSIST aoa E E a 2 51 Over Things That Burn cceseeeeeeeeeee tenes 2 47 Parking Your Vehicle ccsceeeeeeeeeeeeeeeeees 2 46 Passenger Airbag Status Indicator 05 3 34 Passenger Compartment Air Filter 3 28 Passenger Sensing System c eeeeeeeeeneee ees 1 64 PASSING sieni tecutcaceabiat E E E 4 12 Perchlorate Materials Requirements California 5 4 Power Door LOCKS saina aas naaa e aa 2 18 Electrical SySteM ccceeeeeeeeee teense een tenes 5 122 Lumbar Controls d siaii iiinn 1 5 Retained Accessory RAP lecce 2 34 Sed E E E E ET 1 5 Steering Fluid cece eee eee eee eeeeeee ernen e
61. can be dangerous It could affect the braking and handling of your vehicle make your tires lose air and make you lose control You could have a collision in which you or others could be injured Always use the correct wheel wheel bolts and wheel nuts for replacement Notice The wrong wheel can also cause problems with bearing life brake cooling speedometer or odometer calibration headlamp aim bumper height vehicle ground clearance and tire or tire chain clearance to the body and chassis See Changing a Flat Tire on page 5 102 for more information Used Replacement Wheels A CAUTION Putting a used wheel on your vehicle is dangerous You cannot know how it has been used or how far it has been driven It could fail suddenly and cause a crash If you have to replace a wheel use a new GM original equipment wheel 5 82 Tire Chains A CAUTION Do not use tire chains There is not enough clearance Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes suspension or other vehicle parts The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions Follow that manufacturer s instructions To help avoid damage to your vehicle drive slowly re adjust or rem
62. console To use an outlet remove the protective cap When not in use always cover the outlet with the protective cap The accessory power outlet is operational at all times Notice lf electrical devices are left plugged into a power outlet the battery may drain causing your vehicle not to start or damage to the battery This would not be covered by the warranty Always unplug all electrical devices when turning off your vehicle Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses If you experience a problem see your dealer retailer for additional information on accessory power outlets Notice Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should The repairs would not be covered by your warranty Do not use equipment exceeding maximum amperage rating of 20 amperes Check with your dealer retailer before adding electrical equipment Notice Improper use of the power outlet can cause damage not covered by your warranty Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only 3 21 Ashtray s and Cigarette Lighter Your vehicle may have two removable ashtrays and cigarette lighters One ashtray can be placed into the instrument panel storage compartment and the other into the center console rear c
63. controls to the highest heat setting and fan speed and open the windows as necessary If you no longer have the Engine Overheated Idle Engine warning you can drive Just to be safe drive slower for about 10 minutes If the warning does not come back on you can drive normally If the warning continues and you have not stopped pull over stop and park your vehicle right away If there is still no sign of steam you can idle the engine for three minutes while you are parked If you still have the warning turn off the engine and get everyone out of the vehicle until it cools down You may decide not to lift the hood but to get service help right away 5 32 Overheated Engine Protection Operating Mode This operating mode allows your vehicle to be driven to a safe place in an emergency Should a hot engine condition exist an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage In this mode there is a loss in power and engine performance Driving extended miles km and or towing a trailer in the overheat protection mode should be avoided Notice After driving in the overheated engine protection operating mode to avoid engine damage allow the engine to cool before attempting any repair The engine oil will be severely degraded Repair the cause of coolant loss and change the oil See Engine Oil on page 5 16 Cooling System When you decide it is safe to lift the hood here is
64. damage caused by car washes and vandals XM Satellite Radio Antenna System The XM Satellite Radio antenna is located on the roof of your vehicle Keep this antenna clear of snow and ice build up for clear radio reception If your vehicle has a sunroof the performance of the XM system may be affected if the sunroof is open Loading items onto the roof of your vehicle can interfere with the performance of the XM system Make sure the XM Satellite Radio antenna is not obstructed Section 4 Your Driving the Road and Your Vehicle 4 2 Defensive Driving cceeeeeeeeeeeeeeneeeeeeeeeees 4 2 Drunk DIVINO essene a eese aaa E ARE 4 2 Control of a Vehicle ssisesssisssncorsrcsnaries neess 4 3 Braking zeiss orr eaan e E OEN 4 3 Antilock Brake System ABS i c 4 4 Braking in Emergencies seeeeeeeeeeee ener 4 5 Traction Control System TCS o ae 4 6 Limited Slip Rear Axle ccceeeeeeeeeneeeeen teers 4 8 StabiliTrak System cccccccccccccceceeeeeeeeeeees 4 8 Panic Brake ASSIST v c c2 0seecccdeneeetteea sete renee ented 4 9 All Wheel Drive AWD System n 4 9 SIEEN e arsana Ee Ea e E a ERER 4 9 Off Road Recovery seseceesesreseerereerererereeren 4 12 Passing shaa an E E NEEL 4 12 Loss Of COMPTON ires ecceieecheanseneensdencsineccoe eens 4 13 Driving Your Vehicle Competitive Driving cceeeeeeeeeeeeeeeeeee tenes 4 14 Driving at Night ticc cxeeties p
65. date of any service work you perform See Maintenance Record on page 6 15 Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it This can cause wind noise and can affect fuel economy and windshield washer performance Check with your dealer retailer before adding equipment to the outside of your vehicle Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle To help keep the engine clean and maintain optimum vehicle performance we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline The 8th digit of the Vehicle Identification Number VIN shows the code letter or number that identifies your vehicle s engine The VIN is at the top left of the instrument panel See Vehicle Identification Number VIN on page 5 120 Gasoline Octane If your vehicle has the 3 6L V6 engine VIN Code V use regular unleaded gasoline with a posted octane rating of 87 or higher If the octane rating is less than 87 you might notice an audible knocking noise when you drive commonly referred to as spark knock If this occurs use a gasoline rated at 87 octane or higher as soon as possible If you are using gasoline rated at 87 octane or higher and you hear heavy knocking the engine needs service If your vehicle has the 3 6L V6 engine VIN Code 7 use regular unleaded gasoline with a posted octane rating
66. enforcement that have the special equipment can read the information if they have access to the vehicle or the EDR GM will not access this data or share it with others except with the consent of the vehicle owner or if the vehicle is leased with the consent of the lessee in response to an official request of police or similar government office as part of GM s defense of litigation through the discovery process or as required by law Data that GM collects or receives may also be used for GM research needs or may be made available to others for research purposes where a need is shown and the data is not tied to a specific vehicle or vehicle owner OnStar If your vehicle has OnStar and you subscribe to the OnStar services please refer to the OnStar Terms and Conditions for information on data collection and use See also OnStar System on page 2 53 in this manual for more information Navigation System If your vehicle has a navigation system use of the system may result in the storage of destinations addresses telephone numbers and other trip information Refer to the navigation system operating manual for information on stored data and for deletion instructions Radio Frequency Identification RFID RFID technology is used in some vehicles for functions such as tire pressure monitoring and ignition system security as well as in connection with conveniences such as key fobs for remote door locking unlocking
67. engine oil every time you get fuel In order to get an accurate reading the oil must be warm and the vehicle must be on level ground The engine oil dipstick handle is a yellow loop See Engine Compartment Overview on page 5 14 for the location of the engine oil dipstick 1 Turn off the engine and give the oil several minutes to drain back into the oil pan If you do not do this the oil dipstick might not show the actual level 2 Pull out the dipstick and clean it with a paper towel or cloth then push it back in all the way Remove it again keeping the tip down and check the level When to Add Engine Oil If the oil level is within the add cross hatched area at the tip of the dipstick add at least one quart liter of the recommended oil This section explains what kind of oil to use For engine oil crankcase capacity see Capacities and Specifications on page 5 128 Notice Do not add too much oil If the engine has so much oil that the oil level gets above the proper operating range and into the upper cross hatched area on the dipstick the engine could be damaged See Engine Compartment Overview on page 5 14 for the location of the TA engine oil fill cap AAAA Mefpil A SAE 5W 30 Be sure to add enough oil to put the level somewhere in the proper operating range Push the dipstick all the way back in when you are through What Kind of Engine Oil to Use RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS HO
68. exit seat button Button And Automatic Keyless Access default If the features are enabled though the Easy Exit Setup menu the driver s seat will move back and if the vehicle has the power tilt wheel and telescopic steering feature the power steering column will move up and forward when the vehicle is parked and the driver door is opened or after pressing the easy exit seat button The automatic easy exit seat movement will only occur one time after the driver door is opened If the automatic movement has already occurred and you close and then open the driver door the seat and steering column will stay in the original exit position unless a memory recall took place prior to opening the driver door again Button And Automatic Key Access default If the features are enabled though the Easy Exit Setup menu the driver s seat will move back and if the vehicle has the power tilt wheel and telescopic steering feature the power steering column will move up and forward when the key is removed from the ignition or after pressing the easy exit seat button The automatic easy exit seat movement will only occur one time after the key is removed from the ignition If the automatic movement has already occurred and you put the key back in the ignition and remove it again the seat and steering column will stay in the original exit position unless a memory recall took place prior to removing the key again No Change No change wil
69. facing child restraint in the right front passenger s seat if the airbag is turned on If after several seconds both status indicator lights remain on or if there are no lights at all there may be a A CAUTION problem with the lights or the passenger sensing system See your dealer retailer for service Even though the passenger sensing system is designed to turn off the right front passenger s frontal airbag and seat mounted side impact airbag if equipped if the system detects a rear facing child restraint no system is fail safe and no one can guarantee that an airbag will not deploy under some unusual circumstance even though it is turned off We recommend that rear facing child restraints be secured in a rear seat even if the airbag is or airbags are off If the word OFF or the off symbol is lit on the passenger airbag status indicator it means that the passenger sensing system has turned off the right front passenger s frontal airbag and seat mounted side impact airbag See Passenger Sensing System on page 1 64 for more on this including important safety information A CAUTION If the airbag readiness light in the instrument panel cluster ever comes on and stays on it means that something may be wrong with the airbag system If this ever happens have the vehicle serviced promptly because an adult size person sitting in the right front passenger s seat may not have the protection of the airbag s
70. file Sound is heard at a reduced volume The elapsed time of the file displays Release to resume playing the file D gt FWD Fast Forward Press and hold to advance playback quickly within an MP3 WMA file Sound is heard at a reduced volume The elapsed time of the file displays Release to resume playing the file Shuffle With the shuffle setting MP3 WMA files on the CD can be played in random rather than sequential order on the CD currently playing To use shuffle e To play MP3 WMA files from the CD in random order press the pushbutton under the Shuffle label until Shuffle On displays Press again to turn shuffle off XM Radio Messages xL Explicit Language Channels These channels or any others can be blocked at a customer s request by calling 1 800 852 XMXM 9696 XM Updating The encryption code in the receiver is being updated and no action is required This process should take no longer than 30 seconds No XM Signal The system is functioning correctly but the vehicle is in a location that is blocking the XM signal When the vehicle is moved into an open area the signal should return Loading XM The audio system is acquiring and processing audio and text data No action is needed This message should disappear shortly Channel Off Air This channel is not currently in service Tune in to another channel Channel Unavail This previously assigned channel is no longer assigned Tune to another stat
71. for more information 3 33 Passenger Airbag Status Indicator Your vehicle has the passenger sensing system Your instrument panel has a passenger airbag status indicator PASSENGER AIRBAG OFF United States Canada When you start the vehicle the passenger airbag status indicator will light ON and OFF or the symbol for on and off for several seconds as a system check If you use remote start to start your vehicle from a distance if equipped you may not see the system check Then after several more seconds the status indicator will light either ON or OFF or either the on or off symbol to let you know the status of the right front passenger s frontal and seat mounted side impact airbags 3 34 If the word ON or the on symbol is lit on the passenger airbag status indicator it means that the right front passenger s frontal airbag and seat mounted side impact airbag are enabled may inflate A CAUTION If the on indicator comes on when you have a rear facing child restraint installed in the right front passenger s seat it means that the passenger sensing system has not turned off the passenger s frontal airbag and seat mounted side impact airbag if equipped A child in a rear facing child restraint can be seriously injured or killed if the right front passenger s airbag inflates This is because the back of the rear facing child restraint would be very close to the inflating airbag Do not use a rear
72. fully closed 4 Continue holding the switch up for approximately two seconds after the window is completely closed The window is now reprogrammed Repeat the process for the other windows Express Window Anti Pinch Feature If any object is in the path of the window when the express up is active the window will stop at the obstruction and auto reverse to a preset factory position Weather conditions such as severe icing may also cause the window to auto reverse The window will return to normal operation once the obstruction or condition is removed 2 25 Express Window Anti Pinch Override A CAUTION If express override is activated the window will not reverse automatically You or others could be injured and the window could be damaged Before you use express override make sure that all people and obstructions are clear of the window path In an emergency the anti pinch feature can be overridden in a supervised mode Hold the window switch all the way up to the second position The window will rise for as long as the switch is held Once the switch is released the express mode is re activated In this mode the window can still close on an object in its path Use care when using the override mode 2 26 Window Lockout ma Window Lockout The rear window lockout button is located on the driver s door near the window switches Press the right side of the button to disable the rear window controls T
73. ground location is for this purpose Now start the vehicle with the good battery and run the engine for a while Try to start the vehicle that had the dead battery If it will not start after a few tries it probably needs service Notice If the jumper cables are connected or removed in the wrong order electrical shorting may occur and damage the vehicle The repairs would not be covered by your warranty Always connect and remove the jumper cables in the correct order making sure that the cables do not touch each other or other metal Jumper Cable Removal A Heavy Unpainted Metal Engine Part or Remote Negative Terminal B Good Battery or Remote Positive and Remote Negative Terminals C Dead Battery or Remote Positive Terminal To disconnect the jumper cables from both vehicles do the following 1 Disconnect the black negative cable from the vehicle that had the dead battery 2 Disconnect the black negative cable from the vehicle with the good battery 3 Disconnect the red positive cable from the vehicle with the good battery 4 Disconnect the red positive cable from the other vehicle All Wheel Drive If your vehicle is equipped with all wheel drive this is an additional system that needs lubrication Transfer Case When to Check Lubricant It is not necessary to regularly check the transfer case fluid unless you suspect there is a leak or you hear an unus
74. high the throttle is closed to reduce speed If this is not sufficient then the fuel supply to the engine will be limited When the rpms return to normal the fuel supply will return to normal This helps prevent damage to the engine Safety Belt Reminders Safety Belt Reminder Light When the engine is started a chime will come on for several seconds to remind people to fasten their safety belts unless the driver s safety belt is already buckled The safety belt light will also come on and stay on for several seconds then it will flash for several more LZ This chime and light is repeated if the driver remains unbuckled and the vehicle is in motion If the driver s belt is already buckled neither the chime nor the light will come on 3 32 Passenger Safety Belt Reminder Light Several seconds after the engine is started a chime will sound for several seconds to remind the front passenger to buckle their safety belt This would only occur if the passenger airbag is enabled See Passenger Sensing System on page 1 64 for more information The passenger safety belt light located on the instrument panel will come on and stay on for several seconds and then flash for several more This chime and light are repeated if the passenger remains unbuckled and y the vehicle is in motion If the passenger s safety belt is buckled neither the chime nor the light will come on Airbag Readiness Light There is an a
75. ice and avoid sudden steering maneuvers If You Are Caught in a Blizzard If you are stopped by heavy snow you could be in a serious situation You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow Here are some things to do to summon help and keep yourself and your passengers safe e Turn on the hazard warning flashers e Tie a red cloth to your vehicle to alert police that you have been stopped by the snow e Put on extra clothing or wrap a blanket around you If you do not have blankets or extra clothing make body insulators from newspapers burlap bags rags floor mats anything you can wrap around yourself or tuck under your clothing to keep warm You can run the engine to keep warm but be careful 4 20 A CAUTION Snow can trap exhaust gases under your vehicle This can cause deadly CO carbon monoxide gas to get inside CO could overcome you and kill you You cannot see it or smell it so you might not know it is in your vehicle Clear away snow from around the base of your vehicle especially any that is blocking the exhaust pipe And check around again from time to time to be sure snow does not collect there Open a window just a little on the side of the vehicle that is away from the wind This will help keep CO out Run your engine only as long as you must This saves fuel When you run the engine make it go a little f
76. if you need assistance the trunk 5 94 The sealant can only be used to seal one tire After usage the sealant canister and sealant air hose assembly must be replaced at a dealer retailer See Removal and Installation of Sealant Canister later in this section Check the tire sealant expiration date on the sealant canister if it has expired see your dealer retailer for a replacement Using the Tire Sealant and Compressor Kit to Temporarily Seal a Punctured Tire Follow these directions closely for correct sealant usage 1 Do a safety check before proceeding See f a Tire Goes Flat on page 5 83 2 Inspect the damaged tire The sealant cannot seal sidewall damage large punctures or a tire that has unseated from the wheel See Roadside Service on page 7 6 3 If an object such as a nail has penetrated the tire do not remove it Remove the valve stem cap from the flat tire by turning it counterclockwise Place the sealant and compressor kit on the ground and unwrap the sealant air hose G from the compressor 5 95 6 Attach the sealant filling hose G onto the tire valve stem Turn it clockwise until it is tight Make sure the sealant and compressor kit on off A CAUTION switch D is in the O off position 7 Remove the air compressor accessory plug C from the unit Inflating something too much can make it explode and you or others could be injured Be sure to read the inflator instr
77. in appropriate child restraints The harness system holds the infant in place and in a crash acts to keep the infant positioned in the restraint A forward facing child seat B provides restraint for the child s body with the harness 1 39 A booster seat C D is a child restraint designed to improve the fit of the vehicle s safety belt system A booster seat can also help a child to see out the window 1 40 Securing an Add On Child Restraint in the Vehicle A CAUTION A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle Make sure the child restraint is properly installed in the vehicle using the vehicle s safety belt or LATCH system following the instructions that came with that restraint and also the instructions in this manual To help reduce the chance of injury the child restraint must be secured in the vehicle Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap shoulder belt or by the LATCH system See Lower Anchors and Tethers for Children LATCH on page 1 43 for more information A child can be endangered in a crash if the child restraint is not properly secured in the vehicle When securing an add on child restraint refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet or both and to this manual The child rest
78. increasing or decreasing the tire s air pressure for 10 seconds or until a horn chirp sounds The horn chirp which can take up to 30 seconds to sound confirms that the TPMS sensor identification code has been matched to this tire position Proceed to the passenger side front tire and repeat the procedure in Step 5 Proceed to the passenger side rear tire and repeat the procedure in Step 5 Proceed to the driver side rear tire and repeat the procedure in Step 5 After hearing the confirming horn chirp for the driver side rear tire the horn sounds two more times to signal the tire learning mode is no longer active Turn the ignition switch to LOCK OFF Set all four tires to the recommended air pressure level as indicated on the tire and loading information label Put the valve caps back on the valve stems Tire Inspection and Rotation We recommend that you regularly inspect your vehicle s tires including the spare tire for signs of wear or damage See When It Is Time for New Tires on page 5 76 for more information Tires should be rotated every 5 000 to 8 000 miles 8 000 to 13 000 km See Scheduled Maintenance on page 6 4 The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle This will ensure that your vehicle continues to perform most like it did when the tires were new If your vehicle has 235 50ZR18 size tires GM recommends rotating these tir
79. it Adding music to an existing disc can cause the disc not to function Playlists can be selected by using the previous and next folder buttons the SEEK arrows gt gt FWD or 4 lt REV buttons An MP3 WMA CD R or CD RW that was recorded using no file folders can also be played If a CD R or CD RW contains more than the maximum of 50 folders and playlists and 255 files the player lets you access and navigate up to the maximum but all items over the maximum are not accessible The HDD Radio can support more than 255 files on an MP3 WMA disc The HDD Radio does not support playlists on a disc or USB storage device Root Directory The root directory of the CD R or CD RW is treated as a folder If the root directory has compressed audio files the directory displays as F1 DISC All files 3 102 contained directly under the root directory are accessed prior to any root directory folders Playlists Px are always accessed after root folders or files The HDD Radio displays the root directory of an MP3 WMA disc as F1 MP3 and the root directory of a USB storage device as F1 USB Empty Directory or Folder If a root directory or a folder exists somewhere in the file structure that contains only folders subfolders and no compressed files directly beneath them the player advances to the next folder in the file structure that contains compressed audio files No Folder When the CD contains only compressed files the file
80. it to change from high to low beam If the vehicle is turned off while the high beams are on they will come on the next time the vehicle is started The highbeam light on the instrument panel cluster comes on while the high beam headlamps are on Flash to Pass This feature allows you to use the high beam headlamps to signal the driver in front of you that you want to pass Pull and hold the turn signal multifunction lever toward you to use this feature When this is done the following will occur e If the headlamps are off in low beam or in Daytime Running Lamps DRL mode the high beam headlamps will turn on They will stay on as long as the lever is held there Release the lever to turn them off e For vehicles with High Intensity Discharge HID headlamps the low beam headlamps must be on to activate the high beam headlamps See High Intensity Discharge HID Lighting on page 5 55 e If the headlamps are already in high beam mode they will remain on high beam Windshield Wipers The lever on the right side of the steering column operates the windshield wipers w Mist Pull the lever down and release it for a single wiping cycle The lever will return to its original position For more cycles hold the lever down before releasing it Delay Move the lever to this position to set a delay between wipes Turn the delay adjustment band to set the length of the delay Delay Adjustment U
81. like to use to control the garage door and the hand held transmitter button Do not release the Universal Home Remote button or the hand held transmitter button until Step 4 has been completed Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in Gate Operator and Canadian Programming later in this section 4 The indicator light on the Universal Home Remote will flash slowly at first and then rapidly after To program up to three devices 1 From inside the vehicle press and hold down the Universal Home Remote successfully receives the two outside buttons at the same time releasing frequency signal from the hand held transmitter only when the Universal Home Remote indicator Release both buttons light begins to flash after 20 seconds This step will erase the factory settings or all previously programmed buttons 2 58 5 Press and hold the newly trained Universal Home Remote button and observe the indicator light If the indicator light stays on continuously the programming is complete and your garage door should move when the Universal Home Remote button is pressed and released You do not need to continue the programming Steps 6 through 8 and can stop here If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light continue with the programming Steps 6 through 8 It may be helpful to have another person
82. losses in prior crashes In most cases the parts being recycled are from undamaged sections of the vehicle A recycled original equipment GM part may be an acceptable choice to maintain your vehicle s originally designed appearance and safety performance however the history of these parts is not known Such parts are not covered by your GM New Vehicle Limited Warranty and any related failures are not covered by that warranty Aftermarket collision parts are also available These are made by companies other than GM and may not have been tested for your vehicle As a result these parts may fit poorly exhibit premature durability corrosion problems and may not perform properly in subsequent collisions Aftermarket parts are not covered by your GM New Vehicle Limited Warranty and any vehicle failure related to such parts are not covered by that warranty Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs Your GM dealer retailer may have a collision repair center with GM trained technicians and state of the art equipment or be able to recommend a collision repair center that has GM trained technicians and comparable equipment Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage There are significant differences in the quality of coverage afforded by various insurance pol
83. match a transmitter that has already been learned See Keyless Access System Operation on page 2 9 for more information 3 57 Electronic Key Not Detected If your vehicle has the keyless access system this message displays if the vehicle does not detect the presence of a transmitter when you have attempted to start the vehicle or a vehicle door has just closed The following conditions may cause this message to appear Driver added equipment plugged into the accessory power outlet on the center console is causing interference Examples of these devices are cell phones and cell phone chargers two way radios power inverters or similar items Try moving the keyless access transmitter away from these devices when starting the vehicle In addition PDA devices and remote garage and gate openers may also generate Electromagnetic Interference EMI that may interfere with the keyless access transmitter Do not carry the keyless access transmitter in the same pocket or bag as these devices 3 58 The vehicle is experiencing Electromagnetic Interference EMI Some locations such as airports automatic toll booths and some gas stations have EMI fields which may interfere with the keyless access transmitter If moving the transmitter to different locations within the vehicle does not help place the transmitter in the center console transmitter pocket with the buttons facing to the right and then press the START button
84. may not be possible to provide a like vehicle as a courtesy rental Additional Program Information All program options such as shuttle service may not be available at every dealer Please contact your dealer for specific information about availability All Courtesy Transportation arrangements will be administered by appropriate dealer personnel General Motors reserves the right to unilaterally modify change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described herein at its sole discretion Collision Damage Repair If your vehicle is involved in a collision and it is damaged have the damage repaired by a qualified technician using the proper equipment and quality replacement parts Poorly performed collision repairs will diminish your vehicle s resale value and safety performance can be compromised in subsequent collisions Collision Parts Genuine GM Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built Genuine GM Collision parts are your best choice to ensure that your vehicle s designed appearance durability and safety are preserved The use of Genuine GM parts can help maintain your GM New Vehicle Warranty Recycled original equipment parts may also be used for repair These parts are typically removed from vehicles that were total
85. message displays when matching new transmitters to the vehicle See Keyless Access System Operation on page 2 9 for more information Left Rear Door Open This message displays when the driver side rear door is not closed completely Make sure that the door is closed completely Maximum Electronic Keys Learned If your vehicle has the keyless access system this message displays when the maximum number of transmitters have been learned See Keyless Access System Operation on page 2 9 for more information Oil Pressure Low Stop Engine Notice If you drive your vehicle while the engine oil pressure is low severe engine damage may occur If a low oil pressure warning appears on the instrument panel cluster and or DIC stop the vehicle as soon as possible Do not drive the vehicle until the cause of the low oil pressure is corrected See Engine Oil on page 5 16 for more information This message displays when the vehicle s engine oil pressure is low The oil pressure light may also appear on the instrument panel cluster See Oil Pressure Light on page 3 43 See Engine Oil on page 5 16 for more information Stop the vehicle immediately as engine damage can result from driving a vehicle with low oil pressure Have the vehicle serviced by your dealer retailer as soon as possible when this message is displayed Parking Assist Off If your vehicle has the Ultrasonic Rear Parking Assist URPA system after the vehicle has been st
86. neutral detergent solution mixed with water and clean it Make sure the wiping process starts from the center to the edge Care of Your CD or DVD A Player Do not add any label to a disc it could get caught in the CD DVD A player If a disc is recorded on a personal computer and a description label is needed label the top of the recorded disc with a marking pen The use of disc lens cleaners for discs is not advised due to the risk of contaminating the lens of the disc optics with lubricants internal to the CD DVD A player mechanism Notice lf a label is added to a CD or more than one CD is inserted into the slot at a time or an attempt is made to play scratched or damaged CDs the CD player could be damaged While using the CD player use only CDs in good condition without any label load one CD at a time and keep the CD player and the loading slot free of foreign materials liquids and debris If an error displays see Disc Messages later in this section Playing an MP3 WMA Disc Radios with the MP3 feature are capable of playing an MP3 WMA CD R or CD RW disc Radios with the DVD Audio feature are capable of playing MP3 WMA on DVD R discs For more information see Using an MP3 on page 3 107 later in this section Disc Messages DISC ERROR If this message displays and or the disc ejects it could be for one of the following reasons e The radio system does not support the playlist format the compressed aud
87. of the airbag module may be hot for several minutes For location of the airbag modules see What Makes an Airbag Inflate on page 1 62 The parts of the airbag that come into contact with you may be warm but not too hot to touch There may be some smoke and dust coming from the vents in the deflated airbags Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle nor does it prevent people from leaving the vehicle Z CAUTION When an airbag inflates there may be dust in the air This dust could cause breathing problems for people with a history of asthma or other breathing trouble To avoid this everyone in the vehicle should get out as soon as it is safe to do so If you have breathing problems but cannot get out of the vehicle after an airbag inflates then get fresh air by opening a window or a door If you experience breathing problems following an airbag deployment you should seek medical attention Your vehicle has a feature that may automatically unlock the doors turn the interior lamps on and turn the hazard warning flashers on when the airbags inflate You can lock the doors turn the interior lamps off and turn the hazard warning flashers off by using the controls for those features In many crashes severe enough to inflate the airbag windshields are broken by vehicle deformation Additional windshield breakage may also occur from the right front
88. of 87 or higher For best performance or trailer towing you could choose to use middle grade 89 octane unleaded gasoline If the octane rating is less than 87 you might notice an audible knocking noise when you drive commonly referred to as spark knock If this occurs use a gasoline rated at 87 octane or higher as soon as possible If you are using gasoline rated at 87 octane or higher and you hear heavy knocking the engine needs service Gasoline Specifications At a minimum gasoline should meet ASTM specification D 4814 in the United States or CAN CGSB 3 5 or 3 511 in Canada Some gasolines contain an octane enhancing additive called methylcyclopentadienyl manganese tricarbonyl MMT We recommend against the use of gasolines containing MMT See Additives on page 5 6 for additional information California Fuel If your vehicle is certified to meet California Emissions Standards it is designed to operate on fuels that meet California specifications See the underhood emission control label If this fuel is not available in states adopting California emissions standards your vehicle will operate satisfactorily on fuels meeting federal specifications but emission control system performance might be affected The malfunction indicator lamp could turn on and your vehicle might fail a smog check test See Malfunction Indicator Lamp on page 3 40 lf this occurs return to your authorized dealer retailer for diagnosis If it is determ
89. of less than 40 mph 65 km h Safety belts are for everyone How to Wear Safety Belts Properly This section is only for people of adult size Be aware that there are special things to know about safety belts and children And there are different rules for smaller children and babies If a child will be riding in your vehicle see Older Children on page 1 32 or Infants and Young Children on page 1 35 Follow those rules for everyone s protection It is very important for all occupants to buckle up Statistics show that unbelted people are hurt more often in crashes than those who are wearing safety belts Occupants who are not buckled up can be thrown out of the vehicle in a crash And they can strike others in the vehicle who are wearing safety belts First before you or your passenger s wear a safety belt there is important information you should know WO Ss 4 Sit up straight and always keep your feet on the floor in front of you The lap part of the belt should be worn low and snug on the hips just touching the thighs In a crash this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt If you slid under it the belt would apply force on your abdomen This could cause serious or even fatal injuries The shoulder belt should go over the shoulder and across the chest These parts of the body are best able to take belt restraining forces T
90. one that has the replacement number shown on the original battery s label Warning Battery posts terminals and related accessories contain lead and lead compounds chemicals known to the State of California to cause cancer and reproductive harm Wash hands after handling After a power loss such as disconnecting the battery or removing the maxi fuses in the power distribution fuse block the following steps must be performed to calibrate the electronic throttle control If this is not done the engine will not run properly 1 Turn the ignition to ON RUN Do not start the engine 2 Leave the ignition in ON RUN for at least three minutes so that the electronic throttle control will cycle and re learn its home position 3 Turn the ignition to LOCK OFF 4 Start and run the engine for at least 30 seconds 5 43 Vehicle Storage A CAUTION Batteries have acid that can burn you and gas that can explode You can be badly hurt if you are not careful See Jump Siarting on page 5 44 for tips on working around a battery without getting hurt Infrequent Usage If you drive your vehicle infrequently remove the black negative cable from the battery This will help keep the battery from running down Extended Storage For extended storage of your vehicle remove the black negative cable from the battery or use a battery trickle charger This will help maintain the charge of the battery over an extended period
91. or trunk you are opening See Keyless Locking and Keyless Unlock under DIC Vehicle Customization on page 3 68 There are other conditions which can affect the performance of the transmitter See Keyless Access System on page 2 6 Your vehicle comes with two transmitters With Remote Start Shown Without Similar Lock Press to lock the doors The turn signal indicators will flash If is pressed twice the doors will lock the turn signal indicators will flash twice and the horn will sound once You can program your vehicle so the turn signal indicators will not flash and the horn will not sound when pressing on the keyless access transmitter For more information see Remote Door Lock under DIC Vehicle Customization on page 3 68 n Unlock Press n once to unlock the driver s door The turn signal indicators will flash twice Press m twice within five seconds to unlock all the doors If it is dark enough outside your interior lamps will come on You can program your vehicle so the turn signal indicators will not flash and the fog lamps and reverse lamps remain on steady for about 20 seconds when the keyless access transmitter is used to unlock the vehicle See Remote Door Unlock under DIC Vehicle Customization on page 3 68 If your vehicle has the memory feature you can program and recall memory settings when you press m on the keyless access transmitter See Memory Seat and Mirro
92. or a USB storage device The files can be recorded with the following fixed bit rates 32 kbps 40 kbps 56 kbps 64 kbps 80 kbps 96 kbps 112 kbps 128 kbps 160 kbps 192 kbps 224 kbps 256 kbps and 320 kbps or a variable bit rate Song title artist name and album can display when files are recorded using ID3 tags version 1 and 2 Creating an MP3 WMA Disc If you burn your own MP3 WMA disc on a personal computer e Make sure the MP3 WMA files are recorded on a CD R or CD RW disc e Do not mix standard audio and MP3 WMA files on one disc e Make sure the CD does not have more than a maximum of 50 folders and playlists and 255 files to read and play e Create a folder structure that makes it easy to find songs while driving Organize songs by albums using one folder for each album Each folder or album should contain 18 songs or less e Avoid subfolders The system can support up to 8 subfolders deep keep the total number of folders to a minimum to reduce the complexity and confusion during playback e Make sure playlists have a mp3 or wpl extension other file extensions may not work 3 101 e Minimize the length of the file folder or playlist names Long file folder or playlist names or a combination of a large number of files and folders or playlists can cause the player to be unable to play up to the maximum number of files folders playlists or sessions e Finalize the audio disc before burning
93. over an armrest like this The belt would be much too high In a crash you can slide under the belt The belt force would then be applied on the abdomen not on the pelvic bones and that could cause serious or fatal injuries Be sure the belt goes under the armrests 1 21 Q What is wrong with this A CAUTION You can be seriously injured if you wear the shoulder belt under your arm In a crash your body would move too far forward which would increase the chance of head and neck injury Also the belt would apply too much force to the ribs which are not as strong as shoulder bones You could also severely injure internal organs like your liver or spleen The shoulder belt should go over the shoulder and across the chest The shoulder belt is worn under the arm It should be worn over the shoulder at all times 1 22 Q What is wrong with this A CAUTION You can be seriously injured by not wearing the lap shoulder belt properly In a crash you would not be restrained by the shoulder belt Your body could move too far forward ZOA 7 A ry ONES increasing the chance of head and neck injury You might also slide under the lap belt The belt force would then be applied right on the abdomen That could cause serious or fatal injuries The shoulder belt should go over the shoulder and across the chest pa aR N M3 ip A yp LOOX p
94. paint finish can be damaged Be Fluids and Lubricants on page 6 11 p g careful not to spill brake fluid on your vehicle Always clean the brake fluid reservoir cap and the area lf you do wash it off immediately See Washing around the cap before removing it This helps keep Your Vehicle on page 5 115 dirt from entering the reservoir A CAUTION With the wrong kind of fluid in the brake hydraulic system the brakes might not work well This could cause a crash Always use the proper brake fluid 5 41 Brake Wear Your vehicle has disc brakes Disc brake pads have built in wear indicators that make a high pitched warning sound when the brake pads are worn and new pads are needed The sound can come and go or be heard all the time your vehicle is moving except when you are pushing on the brake pedal firmly A CAUTION The brake wear warning sound means that soon the brakes will not work well That could lead to an accident When you hear the brake wear warning sound have your vehicle serviced Notice Continuing to drive with worn out brake pads could result in costly brake repair 5 42 Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied This does not mean something is wrong with the brakes Properly torqued wheel nuts are necessary to help prevent brake pulsation When tires are rotated inspect brake pads for wear and evenly tighten wheel nut
95. parking brake is not set on a manual transmission To recall the stored driving positions when unlocking the vehicle with the transmitter or after the key is placed in the ignition see DIC Vehicle Customization on page 3 68 To stop recall movement of the memory feature at any time press one of the power seat or mirror controls Two personalized exit positions can also be programmed Use the following steps to program exit positions 1 Press memory seat button 1 or the unlock button on the transmitter to recall the driving position 2 Adjust the driver s seat to the desired exit position 3 Press and hold the exit button located above buttons 1 and 2 on the driver s door armrest for at least three seconds Two beeps sound to confirm that the exit position has been saved 4 Repeat the procedure for a second driver using memory seat button 2 or the transmitter To recall the stored exit positions press and release the exit button One beep sounds and the seat moves to the stored exit position for that driver If an exit position has not been stored for this driver the seat moves all the way back The position of the outside mirrors does not change for the exit position If your vehicle has an automatic transmission the vehicle must be in PARK P to recall the exit positions If your vehicle has a manual transmission and the engine is running the parking brake must be set to recall the stored exit positions
96. parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle We recommend the use of genuine parts from your dealer retailer Scheduled Maintenance To maintain the ride handling and performance of your vehicle it is important that the first tire rotation service be performed when the vehicle has 5 000 to 8 000 miles 8 000 to 13 000 km Check tires for inflation pressures and wear See Tires on page 5 59 Rotate tires See Tire Inspection and Rotation on page 5 75 and Tire Wear Inspection in At Least Once a Month on page 6 8 When the Change Engine Oil Soon message in the Driver Information Center DIC comes on it means that service is required for your vehicle Have your vehicle serviced as soon as possible within the next 600 miles 1 000 km It is possible that if you are driving under the best conditions the engine oil life system may not indicate that vehicle service is necessary for over a year However your engine oil and filter must be changed at least once a year and at this time the system must be reset Your dealer retailer has trained service technicians who will perform this work using genuine parts and reset the system If the engine oil life system is ever reset accidentally you must service your vehicle within 3 000 miles 5 000 km since your last service Remember to reset the oil life system whenever the oil is changed See Engine Oil Life System on page 5 19 fo
97. passenger airbag Airbags are designed to inflate only once After an airbag inflates you will need some new parts for the airbag system If you do not get them the airbag system will not be there to help protect you in another crash A new system will include airbag modules and possibly other parts The service manual for your vehicle covers the need to replace other parts Your vehicle has a crash sensing and diagnostic module which records information after a crash See Vehicle Data Recording and Privacy on page 7 16 and Event Data Recorders on page 7 17 Let only qualified technicians work on the airbag systems Improper service can mean that an airbag system will not work properly See your dealer retailer for service 1 63 Passenger Sensing System Your vehicle has a passenger sensing system for the right front passenger s position The passenger airbag status indicator will be visible on the instrument panel when you start your vehicle PASSENGER AIRBAG OFF United States Canada The words ON and OFF or the symbol for on and off will be visible during the system check If you are using remote start to start your vehicle from a distance if equipped you may not see the system check When the system check is complete either the word ON or the word OFF or the symbol for on or the symbol for off will be visible See Passenger Airbag Status Indicator on page 3 34 The passenger sensing system will turn of
98. performed the service and the type of services performed in the boxes provided See Maintenance Requirements on page 6 2 Any additional information from Owner Checks and Services on page 6 8 can be added on the following record pages You should retain all maintenance receipts Maintenance Record Maintenance Record cont d Odometer Reading Serviced By Maintenance Stamp Services Performed Maintenance Record cont d Odometer Reading Serviced By Maintenance Stamp Services Performed Maintenance Record cont d Section 7 Customer Assistance and Information 7 2 Customer Satisfaction Procedure 065 7 2 Online Owner Center cccceceeeeeeeeeeeeeeees 7 4 Customer Assistance for Text Telephone TTY Users 0 eceeeeeeeee eee 7 5 Customer Assistance Offices cceeeeeeeeeee 7 5 GM Mobility Reimbursement Program 7 6 Roadside Service ccceceeeeeeeeeeeeeeeneeaeeaes 7 6 Scheduling Service Appointments 00 7 Courtesy Transportation 0cceseeeeeeeeeeeeeneees 7 9 Collision Damage Repair ceeeeeeeeeeeeeeenes 7 11 Customer Assistance Information Reporting Safety Defects Reporting Safety Defects to the United States Government 6 cece cece cee c eee ec eeeeeeeeeeeeeeeeees Reporting Safety Defects to the Canadian GOVEMMENE scere terinin n irria ee ees Reporting Saf
99. restraint has the LATCH system see Lower Anchors and Tethers for Children LATCH on page 1 43 for how to install your child restraint using LATCH If you secure a child restraint using a safety belt and it uses a top tether see Lower Anchors and Tethers for Children LATCH on page 1 43 for top tether anchor locations Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored or if the instructions that come with the child restraint say that the top strap must be anchored In Canada the law requires that forward facing child restraints have a top tether and that the tether be attached You will be using the lap shoulder belt to secure the child restraint in this position Follow the instructions that came with the child restraint 1 Move the seat as far back as it will go before securing the forward facing child restraint When the passenger sensing system has turned off the right front passenger s frontal airbag and seat mounted side impact airbag the off indicator on the passenger airbag status indicator should light and stay lit when you start the vehicle See Passenger Airbag Status Indicator on page 3 34 2 Put the child restraint on the seat 3 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or around the restraint The child restraint instructions will show you how 4 Push
100. right after Step 10 13 14 15 16 Unplug the air compressor accessory plug F from the accessory power outlet in the vehicle Disconnect the sealant air hose from the tire valve stem or tire pressure monitoring sensor cap by turning it counterclockwise and replace the tire valve stem cap Be careful when handling the tire inflator components as they may be hot after usage Wrap the sealant air hose around the air compressor channel to stow it in its original location Wrap the air compressor accessory plug E back into place 17 If the flat tire was able to inflate to the recommended inflation pressure remove the maximum speed label from the sealant canister Place it in a highly visible location such as the inside of the upper left corner of the windshield or to the face of the radio clock The maximum speed label reminds you to drive cautiously and not to exceed 55 mph 90 km h until you have the damaged tire inspected and repaired A CAUTION Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store the tire sealant and compressor kit in the proper place 18 Return the equipment to the proper storage location in the trunk of your vehicle 5 89 19 20 21 22 23 Immediately drive the vehicle 5 miles 8 km to distribute
101. seat mounted side impact airbag if equipped if the system detects a rear facing child restraint no system is fail safe and no one can guarantee that an airbag will not deploy under some unusual circumstance even though it is turned off We recommend that rear facing child restraints be secured in a rear seat even if the airbag s are off If you secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go It is better to secure the child restraint in a rear seat The passenger sensing system is designed to turn off the right front passenger s frontal airbag and seat mounted side impact airbag if e The right front passenger seat is unoccupied e The system determines that an infant is present in a rear facing infant seat e The system determines that a small child is present in a child restraint e The system determines that a small child is present in a booster seat A right front passenger takes his her weight off of the seat for a period of time e The right front passenger seat is occupied by a smaller person such as a child who has outgrown child restraints e Or if there is a critical problem with the airbag system or the passenger sensing system When the passenger sensing system has turned off the right front passenger s frontal airbag and seat mounted side impact airbag the off indicator will light and stay lit to remind you that
102. see Towing a Trailer on page 4 29 Mirrors Automatic Dimming Rearview Mirror with OnStar The vehicle may have an automatic dimming inside rearview mirror with OnStar controls For more information about OnStar see OnStar System on page 2 53 cb On Off The on off button on the lower left side of the mirror is used for the automatic dimming functions of the rearview mirror Mirror Operation The automatic dimming feature comes on each time the vehicle is started Automatic dimming reduces the glare of lights from behind the vehicle To turn the automatic dimming feature on or off press and release the AUTO O off button The indicator light will come on when this feature is on Cleaning the Mirror When cleaning the mirror use a paper towel or similar material dampened with glass cleaner Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing Outside Power Mirrors The control on the driver side door operates both outside rearview mirrors Press the left or right mirror symbol on the selector switch to choose the driver side or passenger side mirror Once a mirror is selected use the arrows on the control pad to move the mirror to the correct direction Adjust each mirror so you can see the side of your vehicle and the area behind your vehicle The mirrors can be manually folded inward to prevent damage when going through an automatic ca
103. sunroof switches are located on the overhead console The driver side switch operates the sunshade Press and hold the rear of the switch to open the sunshade Press and hold the front of the switch to close the sunshade 2 62 The passenger side switch operates the sunroof Vent Feature Press and hold the front of the switch to vent the sunroof Press and hold the rear of the switch to close the vent Sunroof Feature Press the rear of the switch to open the sunroof and the front of the switch to close it Anti Pinch Feature If an object is in the path of the sunroof when it is closing the anti pinch feature will detect the object and stop the sunroof from closing at the point of the obstruction The sunroof will then return to the full open or vent position To close the sunroof once it has re opened press and hold the front of the passenger s side switch Section 3 Instrument Panel Overview eee 3 4 Hazard Warning Flashers n c 3 6 ROn noaa sebhsenk EE E a ONAA 3 6 Tilt and Telescopic Steering Wheel 3 6 Power Tilt Wheel and Telescopic Steering COMM Meene e a 3 7 Turn Signal Multifunction Lever 0c0ee 3 7 Turn and Lane Change Signals e0e 3 8 Headlamp High Low Beam Changer 3 8 Flash to Pass mai e E TEE 3 9 Windshield Wipers cceeeeeeeeereeeeeeeeeees 3 9 Rainsense Wipers 2 cceceee
104. system and brake system Each of these is covered in this manual and the Index will help you find them quickly If you re trailering it s a good idea to review this information before you start your trip Check periodically to see that all hitch nuts and bolts are tight Engine Cooling When Trailer Towing Your cooling system may temporarily overheat during severe operating conditions See Engine Overheating on page 5 30 4 35 4 NOTES 4 36 Section 5 Service and Appearance Care SEVICE sianie a apea Eii 5 3 Accessories and Modifications cecceeee 5 3 California Proposition 65 Warning 008 5 4 California Perchlorate Materials Requirements 5 4 Doing Your Own Service Work 28 5 4 Adding Equipment to the Outside Of Your VENICE sci ccccesaiecen eriten ancezawe 5 5 UCI EE E EA AAT E E EA 5 5 Gasoline Octane cceeeeeceeeeeeeeeeeeeeaeeeeeneees 5 5 Gasoline Specifications sesisrsicsiirasiir in 5 6 California Fuel cccceeeeeeeeeceeceeeeceeeeeeeeees 5 6 Additive S creaa aeeie a E RE 5 6 Fuels in Foreign Countries 0ceeeeeeeee es 5 7 Filling the Tank wtss cist esecaes sdeunaneh ae cucengenveaereeane 5 8 Filling a Portable Fuel Container 00 5 11 Checking Things Under the Hood 5 12 Hood Release succes civencgetevedansteehi EE 5 13 Engine Compartment Overview s 5 14 Engine Oil sccicticssctveited et a
105. telltale when one or more of your tires is significantly under inflated Accordingly when the low tire pressure telltale illuminates you should stop and check your tires as soon as possible and inflate them to the proper pressure Driving on a significantly under inflated tire causes the tire to overheat and can lead to tire failure Under inflation also reduces fuel efficiency and tire tread life and may affect the vehicle s handling and stopping ability 5 70 Please note that the TPMS is not a substitute for proper tire maintenance and it is the driver s responsibility to maintain correct tire pressure even if under inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly The TPMS malfunction indicator is combined with the low tire pressure telltale When the system detects a malfunction the telltale will flash for approximately one minute and then remain continuously illuminated This sequence will continue upon subsequent vehicle start ups as long as the malfunction exists When the malfunction indicator is illuminated the system may not be able to detect or signal low tire pressure as intended TPMS malfunctions may occur for a variety of reasons including the installation of replacement or alternate tires or wheels on the vehicle that prevent the
106. the sealant is removed within 100 miles 161 kilometers of driving then it is easier to clean from the tire and you are less likely to require a replacement tire owp 5 85 Accessing the Tire Sealant and Compressor Kit A Tire Sealant and Compressor Kit B Foam Container C Wing Nut To access the tire sealant and compressor kit 1 Open the trunk See Trunk on page 2 20 for more information 2 Locate the tire sealant and compressor kit A in the center of the cargo area 5 86 3 Remove the tire sealant and compressor kit by turning the wing nut C counterclockwise 4 Remove the sealant and compressor kit from its foam container B Tire Sealant Read and follow the safe handling instructions on the sealant canister The sealant can temporarily seal small punctures in the tread area of the tire The sealant cannot seal sidewall damage large punctures or a tire that has unseated from the wheel See Roadside Service on page 7 6 if you need assistance The sealant can only be used to seal one tire After usage the sealant canister and sealant filling hose assembly must be replaced at a dealer retailer See Removal and Installation of Sealant Canister later in this section Check the tire sealant expiration date on the sealant canister The sealant might not be effective beyond the expiration date If needed see your dealer retailer for a replacement canister Using the Tire Sealant and Com
107. the Six Disc CD Player the disc number displays at the upper right side of the screen The track number displays at the left and center of the screen The Shuffle Disc and Folder labels appear below Press the pushbutton located under the Shuffle label to play the MP3 WMA files of the currently selected CD in random order Press the pushbuttons located under the Disc or Folder labels to change to another disc or folder As each new track starts to play the track number and song title displays A Eject Press to eject a CD If the CD is not removed after several seconds the CD automatically pulls back into the player and begins playing For the Six Disc CD player press and hold this button for two seconds to eject all discs 3 104 TUNE TONE Turn to select MP3 WMA files on the CD playing Ki SEEK Press the left arrow to go to the start of the current MP3 WMA file if more than five seconds have played Press the right arrow to go to the next MP3 WMA file If either arrow is held or pressed multiple times the player continues moving backward or forward through MP3 WMA files on the CD lt Previous Folder Press the pushbutton under the Folder label to go to the first track in the previous folder gt Next Folder Press the pushbutton under the Folder label to go to the first track in the next folder lt lt REV Reverse Press and hold to reverse playback quickly within an MP3 WMA
108. the difference between the earth s magnetic north and true geographic north If the compass is not set to the zone where you live the compass may give false readings The compass must be set to the variance zone in which the vehicle is traveling To adjust for compass variance use the following procedure Compass Variance Zone Procedure 1 Do not set the compass zone when the vehicle is moving On an automatic transmission vehicle only set it when the vehicle is in PARK P On a manual transmission vehicle only set it when the vehicle is stopped Press the vehicle information button until Press To Change Compass Zone displays Find the vehicle s current location and variance zone number on the map Zones 1 through 15 are available Press the set reset button to scroll through and select the appropriate variance zone Press the trip fuel button until the vehicle heading for example N for North is displayed in the DIC Calibrate the compass See Compass Calibration Procedure following Compass Calibration The compass can be manually calibrated Only calibrate the compass in a magnetically clean and safe location such as an open parking lot where driving the vehicle in circles is not a danger It is suggested to calibrate away from tall buildings utility wires manhole covers or other industrial structures if possible If CAL should ever appear in the
109. the lap belt fit low and snug on the hips touching the thighs If yes continue If no return to the booster seat e Can proper safety belt fit be maintained for the length of the trip If yes continue If no return to the booster seat Q What is the proper way to wear safety belts A An older child should wear a lap shoulder belt and get the additional restraint a shoulder belt can provide The shoulder belt should not cross the face or neck The lap belt should fit snugly below the hips just touching the top of the thighs This applies belt force to the child s pelvic bones in a crash It should never be worn over the abdomen which could cause severe or even fatal internal injuries in a crash Also see Rear Safety Belt Comfort Guides under Lap Shoulder Belt on page 1 25 According to accident statistics children and infants are safer when properly restrained in the rear seating positions than in the front seating positions In a crash children who are not buckled up can strike other people who are buckled up or can be thrown out of the vehicle Older children need to use safety belts properly A CAUTION Never do this Here two children are wearing the same belt The belt cannot properly spread the impact forces In a crash the two children can be crushed together and seriously injured A belt must be used by only one person at a time 1 33 Z CAUTION Never do this Here a child is si
110. the lock button on the transmitter is pressed or the vehicle is no longer off See Remote Keyless Entry RKE System Operation on page 2 7 and Keyless Access System Operation on page 2 9 for more information No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Factory Settings This feature allows you to set all of the customization features back to their factory default settings Press the customization button until Factory Settings appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Restore All default The customization features will be set to their factory default settings Do Not Restore The customization features will not be set to their factory default settings To select a setting press the set reset button while the desired setting is displayed on the DIC Advanced Features If your vehicle has this feature it allows you to enter the advanced features menu Press the customization button until Advanced Features Press V To Enter appears on the DIC display Press the set reset button once to access the advanced feature menu See Advanced Features Menu Items later in this section for more information If you do not press the set reset button Feature
111. the next steps How to Add Manual Transmission Fluid Here is how to add fluid See Recommended Fluids and Lubricants on page 6 11 to determine which type of fluid to use 1 Remove the filler plug 2 Add fluid at the filler plug hole Add only enough fluid to bring the fluid level up to the bottom of the filler plug hole 3 Replace the gasket and reinstall the filler plug Be sure the plug is fully seated 5 26 Hydraulic Clutch It is not necessary to regularly check clutch fluid unless you suspect there is a leak in the system Adding fluid will not correct a leak A fluid loss in this system could indicate a problem Have the system inspected and repaired When to Check and What to Use The hydraulic clutch fluid reservoir cap has this symbol on it See Engine Compartment Overview on page 5 14 for reservoir location E a Refer to the Maintenance Schedule to determine how often you should check the fluid level in your clutch master cylinder reservoir and for the proper fluid to use See Owner Checks and Services on page 6 8 and Recommended Fluids and Lubricants on page 6 11 How to Check and Add Fluid Make sure the fluid level is at the MIN Minimum line on the side of the reservoir If it is not remove the cap and add the proper fluid until the level reaches the MIN line Engine Coolant The cooling system in your vehicle is filled with DEX COOL engine coolant This coolant is designed to remain
112. the road whether it is pavement or gravel the condition of the road whether it is wet dry or icy tire tread the condition of the brakes the weight of the vehicle and the amount of brake force applied Avoid needless heavy braking Some people drive in spurts heavy acceleration followed by heavy braking rather than keeping pace with traffic This is a mistake The brakes might not have time to cool between hard stops The brakes will wear out much faster if you do a lot of heavy braking If you keep pace with the traffic and allow realistic following distances you will eliminate a lot of unnecessary braking That means better braking and longer brake life If your vehicle s engine ever stops while you are driving brake normally but do not pump the brakes If you do the pedal could get harder to push down If the engine stops you will still have some power brake assist But you will use it when you brake Once the power assist is used up it can take longer to stop and the brake pedal will be harder to push Adding non dealer non retailer accessories can affect your vehicle s performance See Accessories and Modifications on page 5 3 Antilock Brake System ABS Your vehicle has the Antilock Brake System ABS an advanced electronic braking system that will help prevent a braking skid When you start the engine and begin to drive away ABS will check itself You might hear a momentary motor or clicking noise
113. tires may not be available for H V W Y and ZR speed rated tires If you choose snow tires with a lower speed rating never exceed the tire s maximum speed capability 5 78 A CAUTION Mixing tires could cause you to lose control while driving If you mix tires of different sizes brands or types radial and bias belted tires the vehicle may not handle properly and you could have a crash Using tires of different sizes brands or types may also cause damage to your vehicle Be sure to use the correct size brand and type of tires on all wheels It is all right to drive with your compact spare temporarily as it was developed for use on your vehicle See Compact Spare Tire on page 5 111 A CAUTION If you use bias ply tires on your vehicle the wheel rim flanges could develop cracks after many miles of driving A tire and or wheel could fail suddenly causing a crash Use only radial ply tires with the wheels on your vehicle If you must replace your vehicle s tires with those that do not have a TPC Spec number make sure they are the same size load range speed rating and construction type radial and bias belted tires as your vehicle s original tires Vehicles that have a tire pressure monitoring system could give an inaccurate low pressure warning if non TPC Spec rated tires are installed on your vehicle Non TPC Spec rated tires may give a low pressure warning that is higher or lower than the proper
114. to GM s specific tire performance criteria have a TPC specification code molded onto the sidewall GM s TPC specifications meet or exceed all federal safety guidelines C DOT Department of Transportation The Department of Transportation DOT code indicates that the tire is in compliance with the U S Department of Transportation Motor Vehicle Safety Standards D Tire Identification Number TIN The letters and numbers following DOT Department of Transportation code is the Tire Identification Number TIN The TIN shows the manufacturer and plant code tire size and date the tire was manufactured The TIN is molded onto both sides of the tire although only one side may have the date of manufacture 5 61 E Tire Ply Material The type of cord and number of plies in the sidewall and under the tread F Uniform Tire Quality Grading UTQG Tire manufacturers are required to grade tires based on three performance factors treadwear traction and temperature resistance For more information see Uniform Tire Quality Grading on page 5 80 G Maximum Cold Inflation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load 5 62 ESS OOOOBSS ay ee 3 9 Q 0 S k2 g a Oe D 9 xal lt 2 OL a1y713N Compact Spare Tire Example A Temporary Use Only The compact spare tire or temporary use tire has a tread life of approximately 3 000 mil
115. to tell when it is time for new tires is to check the treadwear indicators which will appear when your tires have only 1 16 inch 1 6 mm or less of tread remaining change a wheel remove any rust or dirt from places where the wheel attaches to the vehicle In an emergency you can use a cloth or a paper towel to do this but be sure to use a scraper or wire brush later if needed to get all the rust or dirt off See Changing a Flat Tire on page 5 102 5 76 You need new tires if any of the following statements are true e You can see the indicators at three or more places around the tire e You can see cord or fabric showing through the tire s rubber e The tread or sidewall is cracked cut or snagged deep enough to show cord or fabric e The tire has a bump bulge or split e The tire has a puncture cut or other damage that cannot be repaired well because of the size or location of the damage The rubber in tires degrades over time even if they are not being used This is also true for the spare tire if your vehicle has one Multiple conditions affect how fast this aging takes place including temperatures loading conditions and inflation pressure maintenance With proper care and maintenance tires will typically wear out before they degrade due to age If you are unsure about the need to replace your tires as they get older consult the tire manufacturer for more information Buying New Tires G
116. turn on When it is bright enough outside the low beam headlamps will go off and the DRL will turn back on If the vehicle is started in a dark garage the automatic headlamp system comes on immediately Once the vehicle leaves the garage it takes about one minute for the automatic headlamp system to change to DRL if it is light outside During that delay the instrument panel cluster may not be as bright as usual Make sure the instrument panel brightness lever is in the full bright position See Instrument Panel Brightness on page 3 19 3 17 Turning the exterior lamp control to off or to the low beam headlamp position will turn off the DRL If the parking lamps or the fog lamps were turned on instead the DRL will still turn off This will work regardless of gear position and whether or not the parking brake is set Light Sensor The light sensor for the DRL and AUTO headlamp feature is located on top of the instrument panel If the sensor is covered it will prevent it from sensing light and the exterior lamps or the Headlamps Suggested message will appear on the DIC whenever the ignition is on Adaptive Forward Lighting System The Adaptive Forward Lighting System AFL swivels the headlamps horizontally to provide greater road illumination while turning AFL will operate when the vehicle speed is greater than 2 mph 3 km h AFL will not operate when the transmission is in REVERSE R AFL is not immediately operab
117. vehicle many fluids and some component wear by products contain and or emit these chemicals California Perchlorate Materials Requirements Certain types of automotive applications such as airbag initiators seat belt pretensioners and lithium batteries contained in remote keyless entry transmitters may contain perchlorate materials Special handling may be necessary For additional information see www dtsc ca gov hazardouswaste perchlorate Doing Your Own Service Work A CAUTION You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it e Be sure you have sufficient knowledge experience the proper replacement parts and tools before you attempt any vehicle maintenance task Be sure to use the proper nuts bolts and other fasteners English and metric fasteners can be easily confused If you use the wrong fasteners parts can later break or fall off You could be hurt If you want to do some of your own service work you should use the proper service manual It tells you much more about how to service your vehicle than this manual can To order the proper service manual see Service Publications Ordering Information on page 7 15 Your vehicle has an airbag system Before attempting to do your own service work see Servicing Your Airbag Equipped Vehicle on page 1 68 You should keep a record with all parts receipts and list the mileage and the
118. warning The engine could catch fire and you or others could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant A CAUTION Steam and scalding liquids from a hot cooling system can blow out and burn you badly They Notice In cold weather water can freeze and crack are under pressure and if you turn the coolant the engine radiator heater core and other parts surge tank pressure cap even a little they Use the recommended coolant and the proper can come out at high speed Never turn the coolant mixture cap when the cooling system including the coolant surge tank pressure cap is hot Wait for the cooling system and coolant surge tank pressure cap to cool if you ever have to turn the pressure cap 5 35 A CAUTION You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Do not spill coolant on a hot engine If no coolant is visible in the surge tank add coolant as follows 1 Remove the coolant surge tank pressure cap when the cooling system including the coolant surge tank pressure cap and upper radiator hose is no longer hot Turn the pressure cap slowly counterclockwise about one quarter turn and then stop If you hear a hiss wait for that to stop A hiss means there is still some pressure left 5 36 2 Then keep turning the pressure cap slowly and remove it 4 With
119. warning level you would get with TPC Spec rated tires See Tire Pressure Monitor System on page 5 70 Your vehicle s original equipment tires are listed on the Tire and Loading Information Label See Loading Your Vehicle on page 4 22 for more information about the Tire and Loading Information Label and its location on your vehicle Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires this may affect the way your vehicle performs including its braking ride and handling characteristics stability and resistance to rollover Additionally if your vehicle has electronic systems such as anti lock brakes traction control and electronic stability control the performance of these systems can be affected Z CAUTION If you add different sized wheels your vehicle may not provide an acceptable level of performance and safety if tires not recommended for those wheels are selected You may increase the chance that you will crash and suffer serious injury Only use GM specific wheel and tire systems developed for your vehicle and have them properly installed by a GM certified technician See Buying New Tires on page 5 77 and Accessories and Modifications on page 5 3 for additional information 5 79 Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width F
120. what A CAUTION you will see An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you Keep hands clothing and tools away from any underhood electric fan If the coolant inside the coolant surge tank is boiling do not do anything else until it cools down The vehicle should be parked on a level surface A Electric Engine Cooling Fans Out of View B Coolant Surge Tank and Pressure Cap If the engine is warm or hot the coolant level should be at or above the FROID FULL COLD line on the side of the coolant surge tank If the engine is cold the coolant level should be near the FROID FULL COLD line on the side of the coolant surge tank If it is not you could have a leak at the pressure cap or in the radiator hoses heater hoses radiator water pump or somewhere else in the cooling system A CAUTION Heater and radiator hoses and other engine parts can be very hot Do not touch them If you do you can be burned Do not run the engine if there is a leak If you run the engine it could lose all coolant That could cause an engine fire and you could be burned Get any leak fixed before you drive the vehicle 5 34 If there seems to be no leak with the engine on check to see if the electric engine cooling fans are running If the engine hot light is on both fans should be running If they are not
121. while this test is going on and you might even notice that the brake pedal moves a little This is normal If there is a problem with ABS this warning light will stay on See Antilock Brake System Warning Light on page 3 38 Let us say the road is wet and you are driving safely Suddenly an animal jumps out in front of you You slam on the brakes and continue braking Here is what happens with ABS A computer senses that wheels are slowing down If one of the wheels is about to stop rolling the computer will separately work the brakes at each wheel ABS can change the brake pressure faster than any driver could The computer is programmed to make the most of available tire and road conditions This can help you steer around the obstacle while braking hard As you brake the computer keeps receiving updates on wheel speed and controls braking pressure accordingly Remember ABS does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance If you get too close to the vehicle in front of you you will not have time to apply the brakes if that vehicle suddenly slows or stops Always leave enough room up ahead to stop even though you have ABS Using ABS Do not pump the brakes Just hold the brake pedal down firmly and let antilock work for you You might hear the antilock pump or motor operate and feel the brake pedal pulsate but this is normal Braking in Emergencies
122. with the airbag system If this ever happens have the vehicle serviced promptly because an adult size person sitting in the right front passenger s seat may not have the protection of the airbag s See Airbag Readiness Light on page 3 33 for more on this including important safety information Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking which helps the passenger sensing system maintain the passenger airbag status See Safety Belts and Child Restraints in the Index for additional information about the importance of proper restraint use 1 67 A thick layer of additional material such as a blanket or cushion or aftermarket equipment such as seat covers seat heaters and seat massagers can affect how well the passenger sensing system operates We recommend that you not use seat covers or other aftermarket equipment other than any that GM has approved for your specific vehicle See Adding Equipment to Your Airbag Equipped Vehicle on page 1 69 for more information about modifications that can affect how the system operates A CAUTION Siowing of articles under the passenger s seat or between the passenger s seat cushion and seatback may interfere with the proper operation of the passenger sensing system 1 68 Servicing Your Airbag Equipped Vehicle Airbags affect how your vehicle should be serviced There are parts of the airbag system in se
123. your vehicle needs service Notice Engine damage from running your engine without coolant is not covered by your warranty See Overheated Engine Protection Operating Mode on page 5 32 for information on driving to a safe place in an emergency Notice Using coolant other than DEX COOL may cause premature engine heater core or radiator corrosion In addition the engine coolant could require changing sooner at 30 000 miles 50 000 km or 24 months whichever occurs first Any repairs would not be covered by the warranty Always use DEX COOL silicate free coolant in the vehicle How to Add Coolant to the Coolant Surge Tank Z CAUTION If you have not found a problem yet check to see if coolant is visible in the surge tank If coolant is visible Adding only plain water to the cooling system but the coolant level is not at the FROID FULL can be dangerous Plain water or some other COLD line on the side of the coolant surge tank add a liquid such as alcohol can boil before the 50 50 mixture of clean drinkable water and DEX COOL proper coolant mixture will The vehicle s coolant at the coolant surge tank but be sure the cooling system including the coolant surge tank pressure cap is cool before you do it See Engine Coolant on page 5 27 for more information coolant warning system is set for the proper coolant mixture With plain water or the wrong mixture the engine could get too hot but you would not get the overheat
124. 0 kilometers L 100 km This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change Unlike average economy this display cannot be reset AVG Average Speed This display shows the average speed of the vehicle in either miles per hour mph or kilometers per hour km h This average is calculated based on the various vehicle speeds recorded since the last reset of this display To reset this display to zero press the set reset button 3 49 Speedometer This display shows a digital soeedometer in the DIC The speed displays in either miles per hour mph or kilometers per hour km h To change the units from English to metric see Units later in this section Blank Display This display shows no information Vehicle Information Display Menu Items wi Vehicle Information The following display menu items can be displayed by pressing the vehicle information button Oil Life Remaining If the vehicle has this display it shows the estimated oil life remaining If you see 99 Oil Life Remaining on the display that means that 99 of the current oil life remains When the oil life is depleted the Change Engine Oil Soon message appears on the display You should change the oil as soon as possible In addition to the engine oil life system monitoring the oil life additional maintenance is recommended in the Maintenance Schedule in this manual See Sc
125. 2 50 for more information Press the customization button until Park Tilt Mirrors appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off default Neither outside mirror will be tilted down when the vehicle is shifted into REVERSE R Driver Mirror The driver s outside mirror will be tilted down when the vehicle is shifted into REVERSE R Passenger Mirror The passenger s outside mirror will be tilted down when the vehicle is shifted into REVERSE R Both Mirrors The drivers and passenger s outside mirrors will be tilted down when the vehicle is shifted into REVERSE R No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC 3 76 Easy Exit Recall If your vehicle has this feature it allows you to select your preference for the automatic easy exit seat feature See Memory Seat and Mirrors on page 1 6 for more information Press the customization button until Easy Exit Recall appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Door Button Only No automatic seat exit recall will occur The recall will only occur after pressing the easy
126. 2 Owner Checks and Services 6 8 IMMOCUCHION Seo s05 ica oeewpnereeteddacmdhael sibdeues dan sek deacons 6 2 At Each Fuel Pill cncc cc0c t2 acessassetetisecdwtesticbberd 6 8 Maintenance Requirements seeeeeeeee ee 6 2 At Least Once a Month ceeeeeeeeeeeeeee eens 6 8 Your Vehicle and the Environment 6 2 At Least Once a Year n se 6 9 Using the Maintenance Schedule 00 6 2 Recommended Fluids and Lubricants 6 11 Scheduled Maintenance s 6 4 Maintenance Replacement Parts 04 6 13 Additional Required Services 6 5 Engine Drive Belt Routing ccecce 6 14 Maintenance Footnotes ccceeeeeeeeeeeee eters 6 6 Maintenance Record eceeeeeeeeeeeee ee eeeees 6 15 6 1 Maintenance Schedule Introduction Important Keep engine oil at the proper level and change as recommended Protection Plan Have you purchased the GM Protection Plan The Plan supplements your new vehicle warranties See your Warranty and Owner Assistance booklet or your dealer retailer for details Maintenance Requirements Notice Maintenance intervals checks inspections replacement parts and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition Any damage caused by failure to follow scheduled maintenance might not be covered by warranty 6 2 Your Vehicle and the Environ
127. 2008 Cadillac CTS Owner Manual AA Seats and Restraint Systems 006 1 1 Driving Your Vehicle cccceseeeeeeeeees 4 1 Head RestraintS oo ccc ec cc ccccc ec eeeeeeeeeeeeeenenes 1 2 Your Driving the Road and Your Vehicle _ 4 2 Front Seats siccei iwi deaiheaedie shite EE N N 1 4 TOWING seraa aa EA 4 27 Rear SeatS oo ecececcccececcacececcecaceceeeaceeers 1 11 Service and Appearance Care 1 5 1 Safety Bells ccccccceeccecceeeeeeeeeeeeeeeeeees 1 12 SONVICE rrerapen eE ETENE etn TEETE 5 3 Child Restraints civescasacscteecdaveedsasdheavensackins 1 32 UCI modpart E a EE 5 5 Airbag System oo cec cece ccc ec nec eeeeneen snes 1 55 Checking Things Under the Hood _ 5 12 Restraint System Check oo ccceceeeceeeeee neon 1 70 All Wheel Drive oo sce ceeeeeeeceeeeeeeeeeeeeeeeeees 5 49 Features and Controls 0 cccccececeeeeeeeeeeuees 2 1 Rear Axle ga a e a 5 50 KEYS esscrshisiscantiaasaacndiesgahtmcear ra Ea 2 3 Headlamp AiMing ou eee cece ee eeee ee eeeeeeeeeeees 5 51 Doorsvand LOCKS 2fssecseccciiessiviieessecssserbaceeve 2 17 Bulb Replacement cc cece ec cececeeeeeee sees 5 55 WINDOWS geibidicaldhehenapdehelmereelandcdnesoncncueead 2 23 Windshield Wiper Blade Replacement _ 5 57 Theft Deterrent Systems oo eee eeeeeee eee eee ees 2 27 TESS eaea E aetord 5 59 Starting and Operating Your Vehicle
128. 41 Manual USING ccndna aeina a iii Memory Seat and Mirrors o e 1 6 Message DIC Warnings and Messages 0 eeeeeeee 3 54 Mirrors Automatic Dimming Rearview with OnStar 2 49 Outside Convex Mirror ceceeeeeeeeeeeeees 2 50 Outside Heated Mirrors 0cceceeeeeeeeees 2 50 Outside Power Mirrors 0 c0ceeeeeeeeeeeeees 2 49 Park Tilt keines eea EE EREE 2 50 MPS eeina e neko a E EEE E Ee 3 101 MYGMLINK COM si ec0 ccececetsaneasccleeevecss cee eeecssavecee 7 4 Navigation System Privacy cseeeeeeeeeeeeeees 7 18 Navigation Radio System see Navigation M nual att taf neat toes beg nie E 3 106 New Vehicle Break In cceeeeeeeeeeeeeeees 2 31 OQGOMEtER aereis enian ate Er ei 3 31 Odometers Trip eerder ean i ernes 3 31 Off Road RECOVery sesssersrserienieisnenisern irstensines 4 12 Oil ENGINE sasra aa 5 16 Engine Oil Pressure Gage ceeeeeeeee eee ees 3 44 Pressure Light ois siceccss cena natenane 3 43 Oil Engine Oil Life System cece ees 5 19 Older Children Restraints cccccceeeeeee es 1 32 Online Owner Center ccceceeeeeeeeeeneeeeeeees 7 4 OnStar PriVaCy siirsin esencsausbes anereds as veer steve 7 18 OnStar System see OnStar Manual 2 53 Operation Universal Home Remote System 2 57 Outlet Adjustment ceceeeeeeeeeeeeeeeeeeeeeeees 3 27 Outlets Accessory POWER i
129. 9986115 SAE 75W 90 Synthetic Axle Lubricant GM Part No U S 89021677 in Canada 89021678 meeting GM Specification 9986115 With a complete drain and refill add 4 ounces 118 ml of Limited Slip Axle Lubricant Additive GM Part No U S 1052358 in Canada 992694 where required See Rear Axle on page 5 50 Floor Shift Linkage Rear Axle Limited Slip Differential Usage Fluid Lubricant Hood Latch Assembly Lubriplate Lubricant Aerosol Secondary GM Part No U S 12346293 Latch Pivots in Canada 992723 or lubricant Spring Anchor meeting requirements of NLGI 2 and Release Category LB or GC LB Pawl Multi Purpose Lubricant Superlube Hood and Door GM Part No U S 12346241 g in Canada 10953474 Weatherstrip Lubricant GM Part No U S 3634770 in Canada 10953518 or Dielectric Silicone Grease GM Part No U S 12345579 in Canada 992887 Weatherstrip Conditioning Maintenance Replacement Parts Replacement parts identified below by name part number or specification can be obtained from your dealer retailer Oooo om o o o oOo oOo O A ce E Passenger Compartment Ar Eer Emen wos O ooo Spark Plugs 12597464 41 990 Wiper Blades Hook Type Driver s Side 22 inches 56 5 cm 12487636 fF Passenger s Side 21 inches 53 3 cm 12487638 fF OE Engine Drive Belt Routing Maintenance Record After the scheduled services are performed record the date odometer reading who
130. CAUTION Drinking and then driving is very dangerous Your reflexes perceptions attentiveness and judgment can be affected by even a small amount of alcohol You can have a serious or even fatal collision if you drive after drinking Do not drink and drive or ride with a driver who has been drinking Ride home in a cab or if you are with a group designate a driver who will not drink Death and injury associated with drinking and driving is a global tragedy Alcohol affects four things that anyone needs to drive a vehicle judgment muscular coordination vision and attentiveness Police records show that almost 40 percent of all motor vehicle related deaths involve alcohol In most cases these deaths are the result of someone who was drinking and driving In recent years more than 17 000 annual motor vehicle related deaths have been associated with the use of alcohol with about 250 000 people injured For persons under 21 it is against the law in every U S state to drink alcohol There are good medical psychological and developmental reasons for these laws The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive Medical research shows that alcohol in a person s system can make crash injuries worse especially injuries to the brain spinal cord or heart This means that when anyone who has been drinking driver or passenger is in a cras
131. Checking Things Under seeeeeeeeeeee es 5 12 Release mossero ee E EOE 5 13 FIOM scan a E a E ERGE 3 6 How to Wear Safety Belts Properly 1 17 Hydraulic CIUtCH 0 02 0 ccc cec eee ee eee ienien ansaa 5 26 ignition POSITIONS snscieids siecseiseesseeteersitees 2 31 2 33 IMMMODINZEN scaiscnatiateanoiaiiaadsenstapamamuatiundeag asiced 2 28 Immobilizer Operation 0 eee 2 28 2 30 Infants and Young Children Restraints 1 35 Inflation Tire Pressure oo eee eee eee eee ee reenter 5 67 Inflator Kit THC sies ccicisevectsevavcisecstveterasaaen 5 85 5 93 Instrument Panel OVEIVICW E ec eee teeta tense eeeeeeeeeeaees 3 4 Storage Area ii2thsinecietietn as cavities 2 61 Instrument Panel I P BriGhtn Ss ccccfscececleiyeindel nenieptaceetanthel anea 3 19 GIUSIOR E E 3 30 JUMP Stating sects ohac dads cateicnsanaie vse daddegesscadaetens 5 44 Keyless Access System eceeeeeeeeeeeeeeeeeeeees 2 6 Keyless Access System Operation 006 2 9 Keyless Entry System cceeeeeeeeeeeeeeeeeeeeeenes 2 5 KEYS omiaan ae nomad matonade a 2 3 Labeling Tire Sidewall cccceeeeeeeeeeeees 5 61 Lamps Exterior Lighting Battery Saver 3 19 Readingi testades a E a a 3 20 Lap Shoulder Belt cccseseeeeeeeeeeeeeeeeeen ees 1 25 LATCH System Child Restraints ccceeeeeeeeeeeeeeeeeeeeeee eens 1 43 Licen
132. E mca santa meee E 2 17 Lockout Protection ssisssrancenissnniireiuess 2 20 Power DOOP cs csassiecedisivesl icittslasierlnieieeds 2 18 Programmable Automatic Door Locks 2 18 Rear Door Security LOCKS e eeeeeeeeeee ees 2 19 Loss 0f Control icenian anane r oeie 4 13 Lumbar Power Controls ccc ccsesieesedsasavecctsiavsoetewseweeieees 1 5 Maintenance Schedule Additional Required Services eeeeeeeee 6 5 At Each Fuel Fillcsccciccscnesuctencasteveiienthetegeraans 6 8 At Least Once a Month cccccceeeeneeeaees 6 8 At Least Once a Year ccccccc cece ee eeeeeeeeneaees 6 9 INtPOGUCTION 22 0 cece cece cece eee eeeeeneeeeeneeeteneeneenes 6 2 Maintenance Footnotes cccececeseeeeeeeeneee 6 6 Maintenance Record csceeeeceeeeeeeeeeeees 6 15 Maintenance Replacement Parts 5 6 13 Maintenance Requirements eeeeeeeeeee 6 2 Owner Checks and Services ccceceeeeeees 6 8 Recommended Fluids and Lubricants 6 11 Scheduled Maintenance ccccce cece eeeeeee 6 4 USING sncctinss eomericadcbeced ancpoendah ance babawngeneaneniteats 6 2 Your Vehicle and the Environment 6 2 Malfunction Indicator Light o ae 3 40 8 Manual S ats 2 2 saacscgeed secacesdesciecdsinsasesdoneesdesneens 1 4 Manual Transmission PIUIG E E A E oes i vente deecadenee 5 25 OperatioM siciseeee sate sacedeect i AA 2
133. H 4 FIFTH 5 and SIXTH 6 the same way you do for SECOND 2 Slowly let up on the clutch pedal as you press the accelerator pedal To stop let up on the accelerator pedal and press the brake pedal Just before the vehicle stops press the clutch pedal and the brake pedal and shift to NEUTRAL NEUTRAL Use this position when you start or idle your engine Your shift lever is in NEUTRAL when it is centered in the shift pattern not in any gear REVERSE R To back up press down the clutch pedal completely stop the vehicle and shift into REVERSE R Let up on the clutch pedal slowly while pressing the accelerator pedal 2 44 Shift Speeds Manual Transmission A CAUTION If you skip a gear when you downshift you could lose control of your vehicle You could injure yourself or others Do not shift down more than one gear at a time when you downshift Notice If you skip more than one gear when you downshift or if you race the engine when you release the clutch pedal while downshifting you could damage the engine clutch driveshaft or the transmission Do not skip gears or race the engine when downshifting If the vehicle speed drops below 20 mph 32 km h or if the engine is not running smoothly you should downshift to the next lower gear You may have to downshift two or more gears to keep the engine running smoothly or for good performance 2 42 Up Shift Light Vehicles with a manual transmissio
134. Installation of the 9 Turn off the air compressor by pushing the On Off Sealant Canister button B 10 Unplug the air compressor accessory plug E and To remove the sealant canister wrap it back into place 1 Unwrap the sealant and air hose Push the canister release button 2 A CAUTION 3 Pull up and remove the canister 4 Replace with a new canister See your dealer retailer for the new canister Storing the tire sealant and compressor kit or other equipment in the passenger 5 Push the new canister into place compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store the tire sealant and compressor kit in the proper place 5 92 Tire Sealant and Compressor Kit Without Sealant Selector Switch Your vehicle has a tire sealant and compressor kit that is capable of temporarily sealing a small puncture up to 1 4 inch 6 mm in the tread There is no jack or spare tire The kit inflates the tire with liquid sealant and air The tire sealant and compressor kit can also be used to inflate an underinflated tire After the tire is inflated to the recommended inflation pressure see Inflation Tire Pressure on page 5 67 for more information the vehicle must be driven for five miles to distribute the sealant in the tire and seal the puncture After driving five miles the tire pressure must be rechecked and adjusted as needed See Using the Tire Sealant
135. KING sssr mie iacccengaciatauesanpeeeaene precede 2 18 DIG COMPASS acieirar ieat ree 3 52 Diesel Running Out of Fuel aaeeea 2 48 DISC IMPS eree a eaa aN 3 101 Doing Your Own Service Work sseseccesecececeee 5 4 Door Central Door Unlocking System 06 2 17 Delayed Locking osoren 2 18 LOCKS coentre nai E E Oai 2 17 Power Door Loeks riisi dioneatescsaerese monid 2 18 Programmable Automatic Door Locks 2 18 Rear Door Security LOCKS 0 eeeeeeeeeee ees 2 19 Driver Information Center DIC eeeeee 3 47 DIC Operation and Displays eeeeeeeee 3 48 DIC Vehicle Customization ceeeeeeeees 3 68 DIC Warnings and Messages 0 eeeeeeee 3 54 Driving At Night derrin teene otie saa AEN 4 14 Before a Long TTP sassccccscies eens sneenchoamieaeraetnes 4 16 DGIGNSIVG tidcavsseee ity ied cis E de as ests 4 2 Drunken sensn te meusted E 4 2 Highway HypnoSis c ceeeeeeeeeeee eee eeeen ees 4 16 Hill and Mountain Roads 4 17 In Rain and on Wet Roads cece eee 4 15 Rocking Your Vehicle to Get it Out 4 22 Winter seseina e sicge EE 4 18 Dual Climate Control System eeeeeeeeeee 3 23 EDR sie Sea E N 7 16 Electrical System Add On Equipment ceeeeeeneeeeeaeees 5 121 Fuses and Circuit Breakers neccen 5 122 Power Windows and Other Power Options 5 122 Rear Compartment Fuse Blo
136. M has developed and matched specific tires for your vehicle The original equipment tires installed on your vehicle when it was new were designed to meet General Motors Tire Performance Criteria Specification TPC Spec system rating If you need replacement tires GM strongly recommends that you get tires with the same TPC Spec rating This way your vehicle will continue to have tires that are designed to give the same performance and vehicle safety during normal use as the original tires GM s exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle including brake system performance ride and handling traction control and tire pressure monitoring performance GM s TPC Spec number is molded onto the tire s sidewall near the tire size If the tires have an all season tread design the TPC Spec number will be followed by an MS for mud and snow See Tire Sidewall Labeling on page 5 61 for additional information 5 77 GM recommends replacing tires in sets of four This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new Replacing less than a full set of tires can affect the braking and handling performance of your vehicle See Tire Inspection and Rotation on page 5 75 for information on proper tire rotation Winter tires with the same speed rating as your vehicle s original equipment
137. OT motor vehicle safety standards The DOT code includes the Tire Identification Number TIN an alphanumeric designator which can also identify the tire manufacturer production plant brand and date of production GVWR Gross Vehicle Weight Rating See Loading Your Vehicle on page 4 22 GAWR FRT Gross Axle Weight Rating for the front axle See Loading Your Vehicle on page 4 22 GAWR RR Gross Axle Weight Rating for the rear axle See Loading Your Vehicle on page 4 22 Intended Outboard Sidewall The side of an asymmetrical tire that must always face outward when mounted on a vehicle Kilopascal kPa The metric unit for air pressure Light Truck LT Metric Tire A tire used on light duty trucks and some multipurpose passenger vehicles Load Index An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire Maximum Inflation Pressure The maximum air pressure to which a cold tire can be inflated The maximum air pressure is molded onto the sidewall Maximum Load Rating The load rating for a tire at the maximum permissible inflation pressure for that tire Maximum Loaded Vehicle Weight The sum of curb weight accessory weight vehicle capacity weight and production options weight Normal Occupant Weight The number of occupants a vehicle is designed to seat multiplied by 150 Ibs 68 kg See Loading Your Vehicle on page 4 22 5 65 Occupant Distribution Designat
138. P Left Position Lamp Passenger Door Module RT POS LP _ Right Position Lamp Fuses Usage _ _ONSTAR__ Onstar System LT POS LP Left Position Lamp REAR WNDW REAR FOG _ Not Used S ROOF SPARE eae RT POS LP Right Position Lamp AUX OUTLET Auxiliary Power Outlet RVC SNSR __ Regulated Voltage Control Sensor CNSTR VENT Canister Vent Amplifier erate Left Rear Window 5 127 Capacities and Specifications The following approximate capacities are given in English and metric conversions See Recommended Fluids and Lubricants on page 6 11 for more information a neha Engish Merc For the air conditioning system refrigerant charge amount see the refrigerant caution label located under the hood See your dealer retailer for more information 10 3 qt 9 7L Air Conditioning Refrigerant R134a Cooling System 3 6L HFV6 Engine LY7 3 6L HFV6 Engine LLT 10 6 qt 10 0 L Engine Oil with Filter 3 6L HFV6 Engine 5 7L Fuel Tank 68 1 L Transmission Pan Removal and Replacement 6 Speed Automatic 6 3L 6 Speed Manual 1 8L Wheel Nut Torque 140 Nem All capacities are approximate When adding be sure to fill to the approximate level as recommended in this manual Recheck fluid level after filling 5 128 Engine Specifications Engine _VINCode Spark Plug Gap Automatic Automatic 5 129 4 NOTES 5 130 Section 6 Maintenance Schedule Maintenance Schedule 0 ceeeeeeeeneees 6
139. PA 2 51 Uniform Tire Quality Grading eeeeeeeeeeeees 5 80 Universal Home Remote System eeeees 2 56 Operation cideintonceccsntyecbduonrdedaeniarancdenaycaneleens 2 57 Up Shift Light irige cits eee el ies ick 3 36 Using this MAMUall occ sicta ceed ecw scesnemngertvecaner er catmenes iii Vehicle COMO eoriet a E dadicde tae tdacn 4 3 Damage Warnings seeeeeeeeeeeeee eee teeta eee es iv Loading sensderteaeient e r 4 22 Panking YOUT sissies kvener aasian 2 46 SVMBOMS msaren aure eE 61 ETI ESENES iv Vehicle Customization DIC ssssscssscsreerreerrennne 3 68 Vehicle Data Recording and Privacy 7 16 Vehicle Identification Number VIN c eeeeeeeeeeeeeeeeeee reese eeneeees 5 120 Service Parts Identification Label 5 121 Vehicle Remote Start c ccceceecceeeeeeeeeeeees 2 14 Ventilated Seats 2 20 cece cececeeeee nirratais 1 6 Ventilation Adjustment c eeeeeeeeeeeeeeee een eees 3 27 MISOUS aa aae E A atanieeee niecsceauteaatn 2 26 Warning Lights Gages and Indicators 3 29 Warnings DIC Warnings and Messages 0 eeeeeeees 3 54 Hazard Warning Flashers eeeeeeeeeeeeeee 3 6 Safety and Symbols cceeeeeeeeeeeeeeeeeeeeneees iv Vehicle Damage i 2ccecicccsesereccuecscananeecseeneseenees iv Washer Headlamps ceeeeeeeeeeeeeeeeeeees 3 13 Wheels Ali
140. Privacy Policy for the Gracenote service The Gracenote Software and each item of Gracenote Data are licensed to you AS IS Gracenote makes no representations or warranties express or implied regarding the accuracy of any Gracenote Data from in the Gracenote Servers Gracenote reserves the right to delete data from the Gracenote Servers or to change data categories for any cause that Gracenote deems sufficient No warranty is made that the Gracenote Software or Gracenote Servers are error free or that functioning of Gracenote Software or Gracenote Servers will be uninterrupted Gracenote is not obligated to provide you with new enhanced or additional data types or categories that Gracenote may provide in the future and is free to discontinue its services at any time GRACENOTE DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE TITLE AND NON INFRINGEMENT GRACENOTE DOES NOT WARRANT THE RESULTS THAT WILL BE OBTAINED BY YOUR USE OF THE GRACENOTE SOFTWARE OR ANY GRACENOTE SERVER IN NO CASE WILL GRACENOTE BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR FOR ANY LOST PROFITS OR LOST REVENUES Recording From MP3 WMA Discs or USB REC Record While listening to a MP3 WMA disc or a USB device excluding iPod press to start recording songs from the disc The radio has the option to record the current song playing or all
141. S si taoen ea aea RE 3 9 Rat Dre seenen a E E 5 83 Flat Tire Changing isepranmecms eanes an 5 102 Flat Tre StOMNG cates aene nE toes 5 110 FUA isis anana a a A E A 5 25 Automatic Transmission ceecee 5 25 Power Steering ccseeeeeeeeeeeeeeeeeeeeea tented 5 38 Windshield Washer eeeeeeeeeeeeeeeeeees 5 39 Fog Lamp FOG E 3 18 Fog Lamp Light eisite 3 45 Folding Rear Seat erener 1 11 Fuel earen e o RE EO 5 5 Additives esena aa E Ei EUR RS 5 6 California Fuel iseinean niinen aink 5 6 Filling a Portable Fuel Container 005 5 11 Filing the Tank secs 2 ets canimcantevnconetenacasenenemmenns 5 8 Fuels in Foreign Countries cceeeeeeeeeeeees 5 7 Gaje raae O E quads ke E E E 3 46 Gasoline Octane 2 0 0 ceceeeeeeeeeeeeeeeeeeee een een ees 5 5 Gasoline Specifications cceeeeeeeeeeeeeeee ees 5 6 Running Out Of 2 0 2 0 cceeeeeeeeeee eee eee eee eeee teers 2 48 Fuses Fuses and Circuit Breakers eeeeeeees 5 122 Rear Compartment Fuse Block 55 5 126 Underhood Fuse Block cceceeeeeeee eee 5 122 Windshield Wiper ceeeeeeeeeeeeeeeee ee 5 121 G Gage Engine Coolant Temperature eccerre 3 39 Engine Oil Pressure cceseeeeneeeeeaeeee es 3 44 Fuels eaa E tateumohauany sams en Roasts 3 46 Speedometer ccceeeeeeeeeeeeeeeeeeaeeaeeaeeneees 3 31 TACHOMEICN si casted ee cnececamcicenseimetaceeemertceea
142. SC Your automatic transmission has a Driver Shift Control DSC feature that allows you to change gears similar to a manual transmission To use the DSC feature 1 Slide the shift lever over from DRIVE D to the right to MANUAL MODE M If you do not move the shift lever forward or rearward the vehicle will be in sport mode When you are in the sport mode the vehicle will still shift automatically While driving in sport mode the transmission may remain in a gear longer than it would in the normal driving mode based on braking throttle input and vehicle lateral acceleration The SPORT MODE will be displayed in the DIC 2 To enter the DSC mode press the shift lever forward to upshift or rearward to downshift 2 39 The tachometer display on the instrument panel cluster will show which gear the vehicle is in and a number indicating the requested gear range when moving the shift lever forward or rearward See Speedometer and Odometer on page 3 31 for more information on the odometer While using the DSC feature the vehicle will have firmer shifting and increased performance You can use this for sport driving or when climbing or descending hills to stay in gear longer or to down shift for more power or engine braking 2 40 The transmission will only allow you to shift into gears appropriate for the vehicle speed and engine Revolutions Per Minute RPM The transmission will not automatically shift to the next low
143. STAR 1 888 466 7827 or TTY 1 877 248 2080 or press the OnStar button to speak with an OnStar advisor 24 hours a day 7 days a week Not all OnStar features are available on all vehicles To check if your vehicle is equipped to provide the services described below or for a full description of OnStar services and system limitations see the OnStar Owner s Guide in your glove box or visit onstar com OnStar Services For new vehicles with OnStar the Safe amp Sound Plan or the Directions amp Connections Plan is included for one year from the date of purchase You can extend this plan beyond the first year or upgrade to the Directions amp Connections Plan For more information press the OnStar button to speak with an advisor Some OnStar services Such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until you register with OnStar 2 54 Available Services with Safe amp Sound Plan e Automatic Notification of Airbag Deployment e Advanced Automatic Crash Notification AACN If equipped e Link to Emergency Services e Roadside Assistance e Stolen Vehicle Location Assistance e AccidentAssist e Remote Door Unlock Vehicle Alert e OnStar Vehicle Diagnostics GM Goodwrench On Demand Diagnostics e OnStar Hands Free Calling with 30 complimentary minutes e OnStar Virtual Advisor U S Only Available Services included with Directions amp Connections Plan e All Safe and Sound Plan Servi
144. See Keyless Access System Operation on page 2 9 for more information Remote Key Learning Active If your vehicle has the Remote Keyless Entry RKE system this message displays while matching new transmitters to the vehicle See Matching Transmitter s to Your Vehicle under Remote Keyless Entry RKE System Operation on page 2 7 and DIC Operation and Displays on page 3 48 for more information 3 62 Replace Battery In Remote Key This message displays when the battery in the Remote Keyless Entry RKE or keyless access transmitter needs to be replaced To replace the battery see Battery Replacement under Remote Keyless Entry RKE System Operation on page 2 7 or Keyless Access System Operation on page 2 9 Right Rear Door Open This message displays when the passenger side rear door is not closed completely Make sure that the door is closed completely Rotate Control To Off Position If your vehicle has the keyless access system this message displays when the ignition is in ACC ACCESSORY and the shift lever has just been moved to PARK P The message displays as a reminder to turn the ignition off To avoid draining the battery make sure the ignition is turned off before leaving the vehicle Service Air Bag This message displays when there is a problem with the airbag system Have your vehicle serviced by your dealer retailer immediately See Airbag Readiness Light on page 3 33 for more information Serv
145. T WEATHER FIT c LOOK FOR THIS SYMBOL AND GM STANDARD GM4718M DO NOT USE SAE 10W 40 SAE 20W 50 OR ANY OTHER VISCOSITY GRADE OIL NOT RECOMMENDED COLD WEATHER Look for three things e GM4718M Your vehicle s engine requires a special oil meeting GM Standard GM4718M Oils meeting this standard may be identified as synthetic However not all synthetic oils will meet this GM standard Look for and use only an oil that meets GM Standard GM4718M Notice If you use oils that do not have the GM4718M Standard designation you can cause engine damage not covered by your warranty e SAE 5W 30 As shown in the viscosity chart SAE 5W 30 is best for your vehicle These numbers on an oil container show its viscosity or thickness Do not use other viscosity oils such as SAE 20W 50 e Oils meeting these requirements should have the starburst symbol on the container This symbol indicates that the oil has been certified by the American Petroleum Institute API Look for this on the oil container and use only those oils that are identified as meeting GM Standard GM4718M and have the starburst symbol on the front of the oil container Your vehicle s engine is filled at the factory with a Mobil 1 synthetic oil which meets all requirements for your vehicle Substitute Engine Oil When adding oil to maintain engine oil level oil meeting GM Standard GM4718M may not be available You can add substitute oil designated
146. TPMS is not working properly The tire pressure light also flashes and then remains on during the same ignition cycle See Tire Pressure Light on page 3 40 Several conditions may cause this message to appear See Tire Pressure Monitor Operation on page 5 71 for more information If the warning comes on and stays on there may be a problem with the TPMS See your dealer retailer Service Traction Control This message displays when there is a problem with the Traction Control System TCS When this message displays the system will not limit wheel spin Adjust your driving accordingly See your dealer retailer for service See Traction Control System TCS on page 4 6 for more information Service Transmission This message displays when there is a problem with the vehicle s transmission Have your vehicle serviced by your dealer retailer Service Vehicle Soon This message displays when a non emissions related malfunction occurs Have your vehicle serviced by your dealer retailer as soon as possible Shift To Park Automatic Transmission Only If your vehicle has the keyless access system this message displays if the vehicle is not in PARK P while the engine is being turned off The vehicle will be in ACC ACCESSORY Once the shift lever is moved to PARK P the ignition needs to be turned off If the ignition is not turned off the vehicle will remain in ACC ACCESSORY To avoid draining the battery make sure the ignition
147. TPMS from functioning properly Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly See Tire Pressure Monitor Operation on page 5 71 for additional information Federal Communications Commission FCC and Industry and Science Canada The Tire Pressure Monitor System TPMS operates on a radio frequency and complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation The Tire Pressure Monitor System TPMS operates on a radio frequency and complies with RSS 210 of Industry and Science Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment Tire Pressure Monitor Operation The Tire Pressure Monitor System TPMS is designed to warn the driver when a low tire pressure condition exists TPMS sensors are mounted onto each tire and wheel assembly excluding the spare tire a
148. Terminology and Definitions 0 5 64 Inflation Tire Pressure n c 5 67 High Speed Operation ceeeeeeeeeeeee eee ees 5 69 Tire Pressure Monitor System 6 e eeeeees 5 70 Tire Pressure Monitor Operation 06 5 71 Tire Inspection and Rotation cee 5 75 Section 5 When It Is Time for New Tires 0 ee 5 76 Buying New Tires cccsceeeeeeeeeeeeeeteeeeeeees 5 77 Different Size Tires and Wheels 0 0066 5 79 Uniform Tire Quality Grading eeeeeeeeeees 5 80 Wheel Alignment and Tire Balance 5 81 Wheel Replacement 0 eeceeeeeeeeeeerenees 5 81 Tire CHAINS eccsnceoecteeahes tnechmescssntwsd Sacsawsenntas 5 83 If a Tire Goes Flat ircen eiaa 5 83 Tire Sealant and Compressor Kit With Sealant Selector Switch 08 5 85 Tire Sealant and Compressor Kit Without Sealant Selector Switch 5 93 Changing a Flat Tire ccceeeeeeeeeeeeeeeeee es 5 102 Removing the Spare Tire and Tools 5 104 Removing the Flat Tire and Installing tHE Spare Vit secci se enesasechivenae oi Seien OA 5 105 Storing a Flat or Spare Tire and Tools 5 110 Compact Spare Tire cseeeeeeeeeeeeeee ere es 5 111 Appearance Care l a 5 111 Interior Cleaning ceceeeeeneeeeeaeeeeeneeeeeees 5 111 Fabric Carpet eiiis iiinis 5 113 Leathel essare nre a a EEE TEE 5 113 I
149. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions 5 114 Wood Panels Use a clean cloth moistened in warm soapy water use mild dish washing soap Dry the wood immediately with a clean cloth Speaker Covers Vacuum around a speaker cover gently so that the speaker will not be damaged Clean spots with just water and mild soap Care of Safety Belts Keep belts clean and dry A CAUTION Do not bleach or dye safety belts If you do it may severely weaken them In a crash they might not be able to provide adequate protection Clean safety belts only with mild soap and lukewarm water Weatherstrips Silicone grease on weatherstrips will make them last longer seal better and not stick or squeak Apply silicone grease with a clean cloth During very cold damp weather frequent application may be required See Recommended Fluids and Lubricants on page 6 11 Washing Your Vehicle The best way to preserve your vehicle s finish is to keep it clean by washing it often Notice Certain cleaners contain chemicals that can damage the emblems or nameplates on your vehicle Check the cleaning product label If it states that it should not be used on plastic parts do not use it on your vehicle or damage may occur and it would not be covered by the warranty Do not wash the vehicle in direct sunlight Use a car washi
150. The transmitter pocket is inside the center console storage area located between the driver and front passenger seats 2 12 11 12 Insert the vehicle key into the key lock cylinder located on the driver s door Turn the key to the unlock position five times within five seconds The DIC will display Press Start Control To Learn Keys Press the ignition switch in The DIC will read Learn Delay Active Wait XX Min and will count down to zero one minute at a time The DIC will display Press Start Control To Learn Keys again Press the ignition switch in again The DIC will again read Learn Delay Active Wait XX Min and will count down to zero one minute at a time The DIC will display Press Start Control To Learn Keys again Press the ignition switch in again The DIC will again read Learn Delay Active Wait XX Min and will count down to zero one minute at a time 14 A beep will sound and the DIC will read Ready To Learn Electronic Key X At this time all previously known transmitters have been erased 15 Once the transmitter is recognized and programmed a beep will sound and the DIC will display Ready To Learn Electronic Key X 16 To program additional transmitters insert each transmitter in the pocket until you hear a beep and the DIC advances to the next electronic key number 17 When complete press the ignition control knob 18 Press the unlock button on each transmitter progra
151. Trak off if your vehicle gets stuck in sand mud ice or snow and you want to rock your vehicle to attempt to free it or if you are driving in extreme off road conditions and require more wheel spin See f Your Vehicle is Stuck in Sand Mud Ice or Snow on page 4 21 To turn the StabiliTrak system on or off see StabiliTrak System on page 4 8 3 66 There are several conditions that can cause this message to appear e One condition is overheating which could occur if StabiliTrak activates continuously for an extended period of time e The message also displays if the brake system warning light is on See Brake System Warning Light on page 3 37 e The message could display if the stability system takes longer than usual to complete its diagnostic checks due to driving conditions e The message displays if an engine or vehicle related problem has been detected and the vehicle needs service See your dealer retailer The message turns off as soon as the conditions that caused the message to be displayed are no longer present Start Aborted By Theft Deterrent This message displays if there is a communication problem between the keyless access system and the vehicle The vehicle cannot be started when this message displays See your dealer retailer for service Theft Attempted This message displays if the theft deterrent system has detected a break in attempt while you were away from your vehicle See Theft Dete
152. XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces XM Satellite Radio has a wide variety of programming and commercial free music coast to coast and in digital quality sound During your trial or when you subscribe you will get unlimited access to XM Radio Online for when you are not in your vehicle A service fee is required to receive the XM service For more information contact XM at www xmradio com or call 1 800 929 2100 in the U S and www xmradio ca or call 1 877 438 9677 in Canada Radio Messages for XM Only See XM Radio Messages on page 3 105 later in this section for further detail Playing a CD Single Disc Player Insert a CD partway into the slot label side up The player pulls it in The CD track number and a Shuffle label displays The CD begins playback Shuffle Press the pushbutton located below the Shuffle label to play the tracks of a CD in random order Press again to turn Shuffle off Shuffle Off displays Playing a CD s Six Disc CD Player Z Load Press to load CDs into the CD player This CD player holds up to six CDs To insert one CD 1 Press and release the load button 2 Wait for the message to insert the disc 3 Load a CD Insert the CD partway into the slot label side up The player pulls the CD in A Shuffle label and the DISC icon displays 4 Press the pushbutton located bel
153. a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats For any soil always try to remove it first with plain water or club soda Before cleaning gently remove as much of the soil as possible using one of the following techniques e For liquids gently blot the remaining soil with a paper towel Allow the soil to absorb into the paper towel until no more can be removed e For solid dry soils remove as much as possible and then vacuum To clean 1 Saturate a lint free clean white cloth with water or club soda 2 Wring the cloth to remove excess moisture 3 Start on the outside edge of the soil and gently rub toward the center Continue cleaning using a clean area of the cloth each time it becomes soiled 4 Continue to gently rub the soiled area until the cleaning cloth remains clean 5 If the soil is not completely removed use a mild soap solution and repeat the cleaning process that was used with plain water If any of the soil remains a commercial fabric cleaner or spot lifter may be necessary When a commercial upholstery cleaner or spot lifter is to be used test a small hidden area for colorfastness first If the locally cleaned area gives any impression that a ring formation may result clean the entire surface After the cleaning process has been completed a paper towel can be used to blot excess moisture from the fabric or carpet Leather A soft cloth dampened with water can be
154. aces Do not re enter the vehicle while pumping fuel Keep children away from the fuel pump never let children pump fuel The fuel cap is behind a hinged fuel door on the passenger s side of the vehicle The fuel door is opened by pushing in on the rear edge until the door pops out A CAUTION Fuel can spray out on you if you open the fuel cap too quickly If you spill fuel and then something ignites it you could be badly burned This spray can happen if your tank is nearly full and is more likely in hot weather Open the fuel cap slowly and wait for any hiss noise to stop Then unscrew the cap all the way Be careful not to spill fuel Do not top off or overfill the tank and wait a few seconds after you have finished pumping before removing the nozzle Clean fuel from painted surfaces as soon as possible See Washing Your Vehicle on page 5 115 To remove the fuel cap turn it slowly counterclockwise The fuel cap has a spring in it if the cap is released too soon it will spring back to the right While refueling hang the tethered fuel cap from the hook on the fuel door When replacing the fuel cap turn it clockwise until it clicks Make sure the cap is fully installed The diagnostic system can determine if the fuel cap has been left off or improperly installed This would allow fuel to evaporate into the atmosphere See Malfunction Indicator Lamp on page 3 40 The Tighten Gas Cap message in the Driver Informat
155. ad one number but if you enter the freeway the number may change even though you still have the same amount of fuel in the fuel tank This is because different driving conditions produce different fuel economies Generally freeway driving produces better fuel economy than city driving Once the range drops below about 30 miles 48 km remaining the display shows Low Range If your vehicle is low on fuel the Fuel Level Low message displays See Fuel Level Low under DIC Warnings and Messages on page 3 54 for more information AVG Average Economy This display shows the approximate average miles per gallon mpg or liters per 100 kilometers L 100 km This number is calculated based on the number of mpg L 100 km recorded since the last time this display was reset To reset this display to zero press the set reset button Timer This display can be used like a stopwatch You can record the time it takes to travel from one point to another To access the timer press the trip fuel button until Timer 00 00 00 displays To turn on the timer press the set reset button until the timer starts To turn off the timer press the set reset button again The timer stops and displays the end timing value To reset the timer to zero press and hold the set reset button after the timer has been stopped Inst Instantaneous Economy This display shows the current fuel economy in either miles per gallon mpg or liters per 10
156. adio station and stay there The radio only tunes into stations with a strong signal that are in the selected band INFO Information FM RDS XM Satellite Radio Service CD Text CD Gracenote Database HDD MP3 WMA and iPod Press to display additional text information related to the currently playing content When information is not available No Information displays MENU SELECT For FM AM stations the MENU SELECT displays a list of available radio stations Under this menu there is a refresh list selection that allows the user to update the list for all available stations that the radio is able to receive at the current location For XM stations the music guide displays a Category list This list displays all of the Categories available and the number of XM stations available under each Turn the MENU SELECT knob clockwise or counterclockwise to scroll through the list Press this knob to select the desired item The selected item displays a speaker symbol to indicate it is the current active source Finding a XM Station amp Press to switch to XM mode Turn the TUNE TONE knob to select from a list of available XM stations Turn the TUNE TONE knob until the desired station is highlighted Press the TUNE TONE knob to select the highlighted station The highlighted station will also automatically be selected if the TUNE TONE is released and no longer turned Storing a Radio Station as a Favorite D
157. after the key is turned from ON RUN to LOCK OFF Press the customization button until Exit Lighting appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off The exterior lamps will not turn on 30 Seconds default The exterior lamps will stay on for 30 seconds 1 Minute The exterior lamps will stay on for one minute 2 Minutes The exterior lamps will stay on for two minutes No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC 3 72 Approach Lighting This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry RKE or keyless access transmitter Press the customization button until Approach Lighting appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off The exterior lights will not turn on when you unlock the vehicle with the transmitter On default If it is dark enough outside the exterior lights will turn on briefly when you unlock the vehicle with the transmitter The lights will remain on for 20 seconds or until
158. age 5 44 Remote Negative Terminal See Jump Starting on page 5 44 Passenger Compartment Air Filter See Passenger Compartment Air Filter on page 3 28 Engine Cooling Fan See Cooling System on page 5 33 Power Steering Fluid Reservoir Under Engine Cover See Power Steering Fluid on page 5 38 Engine Oil Fill Cap See When to Add Engine Oil under Engine Oil on page 5 16 Engine Oil Dipstick Out of View See Checking Engine Oil under Engine Oil on page 5 16 Hydraulic Clutch Reservoir If Equipped Not Shown See When to Check and What to Use under Hydraulic Clutch on page 5 26 Brake Master Cylinder Reservoir Out of View See Brake Fluid under Brakes on page 5 40 Engine Coolant Surge Tank and Pressure Cap See Coolant Surge Tank Pressure Cap on page 5 30 and Cooling System on page 5 33 Engine Air Cleaner Filter See Engine Air Cleaner Filter on page 5 21 Engine Oil There is an oil pressure light in the instrument cluster and an Oil Pressure Low Stop Engine message on the Driver Information Center DIC If the light and or message appear check the engine oil level right away For more information see Oil Pressure Low Stop Engine under DIC Warnings and Messages on page 3 54 and Oil Pressure Light on page 3 43 You should check the engine oil level regularly this is an added reminder Checking Engine Oil It is a good idea to check the
159. age 6 11 Manual Transmission Fluid When to Check Manual Transmission Fluid It is not necessary to check the manual transmission fluid level A transmission fluid leak is the only reason for fluid loss If a leak occurs take the vehicle to your dealer retailer service department and have it repaired as soon as possible How to Check Manual Transmission Fluid Because this operation can be difficult you may choose to have this done at your dealer retailer service department If you do it yourself be sure to follow all the instructions here or you could get a false reading Notice Too much or too little fluid can damage your transmission Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts starting a fire Too little fluid could cause the transmission to overheat Be sure to get an accurate reading if you check your transmission fluid 5 25 Check the fluid level only when your engine is off the vehicle is parked on a level place and the transmission is cool enough for you to rest your fingers on the transmission case To check the fluid level do the following 1 Remove the filler plug 2 Check that the lubricant level is up to the bottom of the filler plug hole 3 If the fluid level is good replace the gasket and reinstall the filler plug With either vehicle be sure the plug is fully seated If the fluid level is low add more fluid as described in
160. aged The repairs would not be covered by vehicle using a dolly your warranty Do not tow your vehicle with all 1 Put the rear wheels on the dolly four wheels on the ground i Your vehicle was not designed to be towed with all four 2 a altach the Vehicle Deng toWedito Ihe tow wheels on the ground If your vehicle must be towed you should use a dolly See Dolly Towing following for more information 4 28 3 Put the vehicle in PARK P for an automatic transmission or in NEUTRAL for a manual transmission 4 Set the parking brake and then remove the key 5 Clamp the steering wheel in a straight ahead position with a clamping device designed for towing 6 Release the parking brake Dolly Towing All Wheel Drive Vehicles Notice Towing an all wheel drive vehicle with all four wheels on the ground or even with only two of its wheels on the ground will damage drivetrain components Do not tow an all wheel drive vehicle if any of its wheels will be on the ground If you have an All Wheel Drive vehicle it can only be towed on a flat bed trailer Towing a Trailer A CAUTION If you do not use the correct equipment and drive properly you can lose control when you pull a trailer For example if the trailer is too heavy the brakes may not work well or even at all You and your passengers could be seriously injured You may also damage your vehicle the resulting repairs would not be covered by your warranty
161. ailer and then the tongue separately to see if the weights are proper If they are not you may be able to get them right simply by moving some items around in the trailer Total Weight on Your Vehicle s Tires Be sure your vehicle s tires are inflated to the upper limit for cold tires You will find these numbers on the Tire Loading Information label See Loading Your Vehicle on page 4 22 Then be sure you do not go over the GVW limit for your vehicle including the weight of the trailer tongue 4 31 Hitches It is important to have the correct hitch equipment Crosswinds large trucks going by and rough roads are a few reasons why you will need the right hitch Here are some rules to follow e The rear bumper on your vehicle is not intended for hitches Do not attach rental hitches or other bumper type hitches to it Use only a frame mounted hitch that does not attach to the bumper e Will you have to make any holes in the body of your vehicle when you install a trailer hitch If you do then be sure to seal the holes later when you remove the hitch If you do not seal them deadly carbon monoxide CO from your exhaust can get into your vehicle See Engine Exhaust on page 2 47 Dirt and water can also enter the vehicle 4 32 Safety Chains You should always attach chains between your vehicle and your trailer Cross the safety chains under the tongue of the trailer so that the tongue will not drop to the road if it be
162. akes steering and acceleration do not have enough friction where the tires meet the road to do what the driver has asked In any emergency do not give up Keep trying to steer and constantly seek an escape route or area of less danger Skidding In a skid a driver can lose control of the vehicle Defensive drivers avoid most skids by taking reasonable care suited to existing conditions and by not overdriving those conditions But skids are always possible The three types of skids correspond to your vehicle s three control systems In the braking skid the wheels are not rolling In the steering or cornering skid too much speed or steering in a curve causes tires to slip and lose cornering force And in the acceleration skid too much throttle causes the driving wheels to spin A cornering skid is best handled by easing your foot off the accelerator pedal Remember Any traction control system helps avoid only the acceleration skid If your traction control system is off then an acceleration skid is also best handled by easing your foot off the accelerator pedal If your vehicle starts to slide ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go If you start steering quickly enough your vehicle may straighten out Always be ready for a second skid if it occurs Of course traction is reduced when water snow ice gravel or other material is on the road For safety you
163. alant canister B Unwrap the sealant air hose from the compressor 5 101 4 Turn the sealant canister so the inflator filling hose is aligned with the slot in the compressor 5 Lift the sealant canister from the compressor and replace with a new sealant canister See your dealer retailer for more information 5 102 To install a new sealant canister 1 Align the sealant air hose with the slot in the air compressor 2 Push the sealant canister down and turn it clockwise 3 Wrap the sealant air hose around the air compressor channel to stow it in its original location 4 Push the air only hose onto the sealant canister inlet and push the lever down to secure Changing a Flat Tire If a tire goes flat avoid further tire and wheel damage by driving slowly to a level place Turn on your vehicle s hazard warning flashers See Hazard Warning Flashers on page 3 6 for more information When your vehicle has a flat tire use the following example as a guide to assist you in the placement of A CAUTION wheel blocks Changing a tire can be dangerous The vehicle can slip off the jack and roll over or fall on you or other people You and they could be badly injured or even killed Find a level place to change your tire To help prevent the vehicle gt roni moving SEA Set the parking brake firmly Put the shift lever in PARK P Turn off the engine and do not restart while the vehicle is
164. amage from road hazards A vehicle specific Tire and Loading Information label is attached to your vehicle This label lists your vehicle s original equipment tires and shows the correct inflation pressures for your tires when they are cold The recommended cold tire inflation pressure shown on the label is the minimum amount of air pressure needed to support your vehicle s maximum load carrying capacity For additional information regarding how much weight your vehicle can carry and an example of the tire and loading information label see Loading Your Vehicle on page 4 22 How you load your vehicle affects vehicle handling and ride comfort Never load your vehicle with more weight than it was designed to carry 5 67 When to Check Check your tires once a month or more Do not forget to check the compact spare tire if your vehicle has one The compact spare should be at 60 psi 420 kPa For additional information regarding the compact spare tire see Compact Spare Tire on page 5 111 How to Check Use a good quality pocket type gage to check tire pressure You cannot tell if your tires are properly inflated simply by looking at them Radial tires may look properly inflated even when they are underinflated Check the tire s inflation pressure when the tires are cold Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile 1 6 km 5 68 Remove the valve cap from the tire val
165. and starting and in vehicle transmitters for garage door openers RFID technology in GM vehicles does not use or record personal information or link with any other GM system containing personal information A Accessories and Modifications eeeeee 5 3 Adaptive Forward Lighting System 00 3 18 Adding Equipment to Your Airbag Equipped VENICE netoen a a E NE 1 69 Additives Fuel c ccccececeeeceeeeeeeeeeteneeetenees 5 6 Add On Electrical Equipment 0 eeeeee 5 121 Air Cleaner Filter Engine eeeeeeeeeeeneee es 5 21 Air GOmditioning ssi icc scccas aeii ia 3 23 Airbag Passenger Status Indicator eeeeeeeeees 3 34 Readiness Light ccceeeeeeeeeeeeseeeereeees 3 33 Airbag System sprene errori iinn raau tnis 1 55 What Will You See After an Airbag Inflates 1 62 When Should an Airbag Inflate 6 1 60 Where Are the Airbags ceeeeeeeeeeeeeees 1 58 Airbag Systems Adding Equipment to Your Airbag Equipped VONICIO casctnnendencxcasendhdaenntntnanivacexctagauiesen 1 69 How Does an Airbag Restrain eeee 1 62 Passenger Sensing System eeeeeeeeeees 1 64 Servicing Your Airbag Equipped Vehicle 1 68 What Makes an Airbag Inflate 08 1 62 All Whieel Drive ws ic scccecencecnieceetetece naa 5 49 All Wheel Drive AWD System 4 9 Analog ClOCK cagacusctejasssed
166. and Compressor Kit later in this section Be sure to read and follow all of the tire sealant and compressor kit instructions The kit includes A Air Compressor D On Off Switch B Tire Sealant Canister E Air Pressure Gage C Air Compressor F Air Only Hose Accessory Plug G Sealant Air Hose After temporarily sealing and inflating the with the tire sealant and compressor kit it is recommended to take your vehicle to an authorized dealer retailer as soon as possible for tire repair or replacement If the sealant is removed within 100 miles 161 kilometers of driving then it is easier to clean from the tire and you are less likely to require a replacement tire 5 93 3 Remove the tire sealant and compressor kit strap by squeezing the two tabs of the quick release buckle Accessing the Tire Sealant and Compressor Kit To access the tire sealant and compressor kit 1 Open the trunk See Trunk on page 2 20 for more information 4 Remove the sealant and compressor kit from its foam container Tire Sealant Read and follow the safe handling instructions on the sealant canister The sealant can temporarily seal a puncture up to Ya inch 6 mm in the tread area of the tire The sealant cannot seal sidewall damage large punctures or a 2 Locate the tire sealant and compressor kit on the tire that has unseated from the wheel See Roadside driver side of the vehicle near the back corner of Service on page 7 6
167. and a 2 0 stereo audio stream available Press the pushbutton located under the Audio label to display the current audio stream playing Audio Stream 1 or Audio Stream 2 briefly displays Press the pushbutton located under the Audio label again to toggle between Audio Stream 1 or Audio Stream 2 if available Check the DSP settings to determine if a 5 1 surround sound Audio Stream is playing See Digital Signal Processing DSP earlier in this section Press the DSP label to see if the 5 1 Normal or 5 1 Rear settings are available for selection If these settings are available Audio Stream 1 is playing 3 90 Care of Your CD and DVD A Discs If playing a CD or DVD A disc the sound quality can be reduced due to disc quality the method of recording the quality of the music that has been recorded and the way the disc has been handled Handle them carefully Store disc s in their original cases or other protective cases and away from direct sunlight and dust The CD DVD A player scans the bottom surface of the disc If the surface of a disc is damaged such as cracked broken or scratched the disc may not play properly or not at all Do not touch the bottom side of a disc while handling it this could damage the surface Pick up discs by grasping the outer edges or the edge of the hole and the outer edge If the surface of a disc is soiled take a soft lint free cloth or dampen a clean soft cloth in a mild
168. anister compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store the tire sealant and compressor kit in the proper place Place it in a highly visible location such as the inside of the upper left corner of the windshield or ee to the face of the radio clock location in the trunk of your vehicle The maximum speed label reminds you to drive 20 Immediately drive the vehicle 5 miles 8 km to cautiously and not to exceed 55 mph 90 km h until distribute the sealant evenly in the tire Stop at you have the damaged tire inspected and repaired a safe location and check the tire pressure refer to Steps 1 through 8 under Using the Air Compressor without Sealant to Inflate an Underinflated Tire Not Punctured next in this section 19 Return the equipment to its original storage 5 98 21 22 23 24 If the tire pressure has fallen more then 10 psi 68 kPa below the recommended inflation pressure stop driving the vehicle The tire is too severely damaged and the tire sealant and compressor kit cannot seal the tire See Roadside Service on page 7 6 for more information If the tire pressure has not dropped more than 10 psi 68 kPa from the recommended inflation pressure you can inflate the tire back up to the recommended inflation pressure Wipe off any sealant from the wheel tire and vehicle Dispose of the sealant canister B and seal
169. ant air hose G at a local dealer retailer or in accordance with your local state codes and practices After using the sealant canister replace it with a new canister from your dealer retailer After temporarily sealing a tire with the tire sealant and compressor kit take your vehicle to your dealer retailer to have the tire inspected and repaired or replaced Using the Air Compressor without Sealant to Inflate an Underinflated Tire Not Punctured To use the air compressor to inflate a tire with air only and not sealant 1 Do a safety check before proceeding See f a Tire Goes Flat on page 5 83 2 Inspect the damaged tire The sealant cannot seal sidewall damage large punctures or a tire that has unseated from the wheel See Roadside Service on page 7 6 3 If an object such as a nail has penetrated the tire do not remove it 4 Unlock the air compressor hose from the sealant canister by pulling up on the lever 5 99 A CAUTION Idling the engine in a closed in place or with the climate control system off can cause deadly carbon monoxide CO See Engine Exhaust on page 2 47 8 Start the vehicle See Starting the Engine on page 2 34 for more information The vehicle must be running while using the air compressor A CAUTION Inflating something too much can make it 5 Pull the air only hose F from the sealant explode and you or others could be injured canister B p Be
170. approved cleaners on aluminum or chrome plated wheels The surface of these wheels is similar to the painted surface of your vehicle Do not use strong soaps chemicals abrasive polishes abrasive cleaners cleaners with acid or abrasive cleaning brushes on them because you could damage the surface Do not use chrome polish on aluminum wheels 5 117 Notice Using chrome polish on aluminum wheels could damage the wheels The repairs would not be covered by your warranty Use chrome polish on chrome wheels only Use chrome polish only on chrome plated wheels but avoid any painted surface of the wheel and buff off immediately after application Notice If you drive your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes you could damage the aluminum or chrome plated wheels The repairs would not be covered by your warranty Never drive a vehicle equipped with aluminum or chrome plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes Tires To clean the tires use a stiff brush with tire cleaner Notice Using petroleum based tire dressing products on your vehicle may damage the paint finish and or tires When applying a tire dressing always wipe off any overspray from all painted surfaces on your vehicle 5 118 Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement make sure the body repair shop applies anti
171. ar Window Defogger Press this button to turn the rear window defogger on or off Be sure to clear as much snow from the rear window as possible The rear window defogger turns off about 15 minutes after the button is first pressed if the vehicle is moving at slower speeds At higher speeds the rear window defogger may stay on continuously With each additional press the defogger runs for about 10 minutes The defogger can also be turned off by pressing the button again or by turning off the engine The heated outside rearview mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defogger button is on See Outside Heated Mirrors on page 2 50 Notice Do not try to clear frost or other material from the inside of the front windshield and rear window with a razor blade or anything else that is sharp This may damage the rear window defogger grid and affect your radio s ability to pick up stations clearly The repairs wouldn t be covered by your warranty Sensors There is a solar sensor located on the instrument panel near the windshield There is also an interior temperature sensor located to the right of the steering wheel on the instrument panel By monitoring the solar radiation and the air inside the vehicle these sensors help maintain the selected temperature by adjusting the fan speed and the air delivery system In order to do this the system can also supply cool
172. arted this message displays to remind the driver that the URPA system has been turned off Press the set reset button to acknowledge this message and clear it from the DIC display To turn the URPA system back on see Parking Assist under DIC Operation and Displays on page 3 48 See Ultrasonic Rear Parking Assist URPA on page 2 51 for more information Passenger Door Open This message displays when the passenger side front door is not closed completely Make sure that the door is closed completely Press Brake To Start Engine Automatic Transmission Only If your vehicle has the keyless access system this message displays if you try to start the engine without having the brake pressed The brake needs to be pressed when starting the engine See gnition Positions Key Access on page 2 31 or Ignition Positions Keyless Access on page 2 33 for more information 3 61 Press Start Control To Learn Keys If your vehicle has the keyless access system this message displays when matching new transmitters to the vehicle See Keyless Access System Operation on page 2 9 for more information Rainsense Wipers Active If your vehicle has this feature this message displays while the Rainsense wipers are active See Rainsense Wipers on page 3 10 for more information Ready To Learn Electronic Key X If your vehicle has the keyless access system this message displays while matching new transmitters to the vehicle
173. aster than just idle That is push the accelerator slightly This uses less fuel for the heat that you get and it keeps the battery charged You will need a well charged battery to restart the vehicle and possibly for signaling later on with the headlamps Let the heater run for a while Then shut the engine off and close the window almost all the way to preserve the heat Start the engine again and repeat this only when you feel really uncomfortable from the cold But do it as little as possible Preserve the fuel as long as you can To help keep warm you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes If Your Vehicle is Stuck in Sand Mud Ice or Snow Slowly and cautiously spin the wheels to free your vehicle when stuck in sand mud ice or snow See Rocking Your Vehicle to Get It Out on page 4 22 If your vehicle has a traction system it can often help to free a stuck vehicle Refer to your vehicle s traction system in the Index If the stuck condition is too severe for the traction system to free the vehicle turn the traction system off and use the rocking method A CAUTION If you let your vehicle s tires spin at high speed they can explode and you or others could be injured The vehicle can overheat causing an engine compartment fire or other damage Spin the wheels as little as possible and avoid going above 35 mph 55 km h as shown on the speedometer
174. ation information about your vehicle is only available if the GPS satellite signals are unobstructed and available Your vehicle must have a working electrical system including adequate battery power for the OnStar equipment to operate There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place Some examples are damage to important parts of your vehicle in an accident hills tall buildings tunnels weather or wireless phone network congestion Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor If the light next to the OnStar buttons is red this means that your system is not functioning properly and should be checked by your dealer retailer If the light appears clear no light is appearing your OnStar 2 56 subscription has expired You can always press the OnStar button to confirm that your OnStar equipment is active Universal Home Remote System Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand held Radio Frequency RF transmitters used to activate devices such as garage door openers security systems and home lighting This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interfer
175. ation on the radio s display To connect and control your iPod using the radio controls your vehicle must have a USB port If it does it is located in the center console bin You will also need a special iPod connection cable that can be purchased with your vehicle or may be available after from your dealer retailer See your dealer retailer for more information This feature supports the following iPod models e Fifth generation or later iPod e First or Second generation or later iPod Nano For proper operation make sure your iPod has the latest firmware from Apple Your iPod firmware can be updated using the latest iTunes application See www apple com itunes To connect and control your iPod connect one end of the specially purchased iPod connection cable to the iPod s dock connector Connect the other end to both the USB 3 100 port and the auxiliary input jack The USB port and the auxiliary input jack are located in the center console bin If the vehicle is on and the USB connection works you will see a GM logo appear on your iPod Your iPod music will display on your radio s display and begin playing through your vehicle radio system A standard iPod USB cable like the one that came with your iPod cannot be used to connect an iPod to your vehicle You must use the iPod connection cable that was purchased with your vehicle or that was made available from your dealer retailer in order for this feature to work
176. available to assist with the remaining steps Sap Canoe orc Oo 6 After Steps 1 through 5 have been completed locate inside the garage the garage door opener receiver motor head unit Locate the Learn or Smart button The name and color of the button may vary by manufacturer 7 Firmly press and release the Learn or Smart button After you press this button you will have 30 seconds to complete Step 8 2 59 8 Immediately return to the vehicle Firmly press and hold the Universal Home Remote button chosen in Step 3 to control the garage door for two seconds and then release it If the garage door does not move press and hold the same button a second time for two seconds and then release it Again if the door does not move press and hold the same button a third time for two seconds and then release The Universal Home Remote should now activate the garage door To program the remaining two Universal Home Remote buttons begin with Step 2 of Programming the Universal Home Remote System Do not repeat Step 1 as this will erase all previous programming from the Universal Home Remote buttons Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System call 1 800 355 3515 or go to www homelink com Canadian radio frequency laws require transmitter signals to time out or quit after several seconds of transmission
177. ay be less while the vehicle is running As a result you may need to be closer to your vehicle to turn it off than you were to turn it on There are other conditions which can affect the performance of the transmitter see Remote Keyless Entry RKE System on page 2 5 or Keyless Access System on page 2 6 for additional information Q Remote Start Press and release the lock button and then press and hold this button to use the remote start feature To start the vehicle using the remote start feature 1 Aim the transmitter at the vehicle 2 Press and release the transmitter s lock button then immediately press and hold the transmitter s remote start button until the turn signal lights flash or if the vehicle s lights are not visible press and hold the remote start button for at least four seconds The vehicle s doors will lock Pressing the remote start button again after the vehicle has started will turn off the ignition When the vehicle starts the parking lamps will turn on and remain on while the vehicle is running 3 If it is the first remote start since the vehicle has been driven repeat these steps while the engine is still running to extend the engine running time by 10 minutes Remote start can be extended one time After entering the vehicle during a remote start press the brake pedal and turn the ignition to ON RUN to drive the vehicle If the vehicle is left running it will automatically shut off
178. ay illuminate in the rear display Once the attached object is removed URPA will return to normal operation e A tow bar is attached to your vehicle e The vehicle s bumper is damaged Take the vehicle to your dealer retailer to repair the system e Other conditions may affect system performance such as vibrations from a jackhammer or the compression of air brakes on a very large truck If the system is still disabled after driving forward at least 15 mph 25 km h take your vehicle to your dealer retailer OnStar System OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety security information and convenience services If your airbags deploy the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location If you lock your keys in the vehicle call OnStar at 1 888 4 ONSTAR and they can send a signal to unlock your doors If you need roadside assistance press the OnStar button and they can contact Roadside Service for you 2 53 OnStar service is provided to you subject to the OnStar Terms and Conditions You may cancel your OnStar service at any time by contacting OnStar A complete OnStar Owner s Guide and the OnStar Terms and Conditions are included in the vehicle s OnStar Subscriber glove box literature For more information visit onstar com or onstar ca contact OnStar at 1 888 4 ON
179. ayed When locking the doors with the power door lock switch and a door is open this feature will delay locking the doors until five seconds after the last door is closed You will hear three chimes to signal that the delayed locking feature is in use On vehicles with the Remote Keyless Entry RKE system the key must be out of the ignition for this feature to work On vehicles with the Keyless Access System the vehicle must be off and the keyless access transmitter must be removed from the vehicle for this feature to work You can temporarily override delayed locking by pressing the power door lock switch twice or the lock button on the transmitter twice See Delayed Locking on page 2 18 for more information Press the customization button until Delay Door Lock appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off There will be no delayed locking of the vehicle s doors On default The doors will not lock until five seconds after the last door is closed No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC 3 71 Exit Lighting This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside This happens
180. begins to move To stop the chime fully release the parking brake If you are towing a trailer and parking on a hill see Towing a Trailer on page 4 29 for more information 2 43 Shifting Into PARK P Automatic Transmission A CAUTION It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle will not move even when you are on fairly level ground use the steps that follow If you are pulling a trailer see Towing a Trailer on page 4 29 Use this procedure to shift into PARK P 1 Hold the brake pedal down with your right foot and set the parking brake See Parking Brake on page 2 43 for more information 2 Move the shift lever into PARK P by holding in the button on the shift lever and pushing the lever all the way toward the front of the vehicle 2 44 3 Turn the ignition to LOCK OFF 4 For vehicles with key access remove the key and take it with you If you can leave your vehicle with the ignition key in your hand your vehicle is in PARK P Vehicles with the keyless access system take the keyless access transmitter with you Leaving Your Vehicle With the Engine Running Automatic Transmission A CAUTION It can be dangerous to leave your vehicle with the engine running Your vehic
181. by safety belts Even though today s airbags are also designed to help reduce the risk of injury from the force of an inflating bag all airbags must inflate very quickly to do their job Here are the most important things to know about the airbag system A CAUTION You can be severely injured or killed in a crash if you are not wearing your safety belt even if you have airbags Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it Airbags are supplemental restraints to the safety belts All airbags are designed to work with safety belts but do not replace them 1 56 A CAUTION Frontal airbags are designed to deploy in moderate to severe frontal and near frontal crashes They are not designed to inflate in rollover rear crashes or in many side crashes Seat mounted side impact airbags are designed to inflate in moderate to severe crashes where something hits the side of your vehicle They are not designed to inflate in frontal in rollover or in rear crashes Roof rail airbags are designed to inflate in moderate to severe crashes where something hits the side of your vehicle or in a severe frontal impact They are not designed to inflate in rollover or rear crashes Everyone in your vehicle should wear a safety belt properly whether or not there is an airbag for that person A CAUTION Airbags plus lap shoulder belt
182. c fan Your vehicle has a remote negative ground location as shown in the illustration It is located on the rear passenger side of the vehicle See Engine Compartment Overview on page 5 14 You should always use this remote ground location instead of the terminal on the battery 5 46 A CAUTION A CAUTION Using a match near a battery can cause battery gas to explode People have been hurt doing this and some have been blinded Use a flashlight if you need more light Be sure the battery has enough water You do 5 Check that the jumper cables do not have loose or not need to add water to the battery installed missing insulation If they do you could get a in your new vehicle But if a battery has filler shock The vehicles could be damaged too caps be sure the right amount of fluid is there Before you connect the cables here are some If it is low add water to take care of that first basic things you should know Positive will go to If you do not explosive gas could be present positive or to a remote positive terminal if the vehicle has one Negative will go to a heavy unpainted metal engine part or to a remote Fans or other moving engine parts can injure you badly Keep your hands away from moving parts once the engine is running Battery fluid contains acid that can burn you Do not get it on you If you accidentally get it negative terminal if the vehicle has one in your eyes or
183. ces e Driving Directions Advisor delivered or OnStar Turn by Turn Navigation If equipped e RideAssist e Information and Convenience Services OnStar Hands Free Calling OnStar Hands Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands Hands Free Calling is fully integrated into the vehicle and can be used with OnStar Pre Paid Minute Packages Hands Free Calling may also be linked to a Verizon Wireless service plan in the U S or a Bell Mobility service plan in Canada depending on eligibility To find out more refer to the OnStar Owner s Guide in the vehicle s glove box visit www onstar com or www onstar ca or speak with an OnStar advisor by pressing the OnStar button or calling 1 888 4 ONSTAR 1 888 466 7827 OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands Free Calling that uses your minutes to access location based weather local traffic reports and stock quotes By pressing the phone button and giving a few simple voice commands you can browse through the various topics See the OnStar Owners Guide for more information Only available in the continental U S OnStar Steering Wheel Controls Your vehicle may have a Talk Mute button that can be used to interact with OnStar Hands Free Calling See Audio Steering Wheel Controls on page 3 106 for more information On some vehicles you may have to hold the button for a few seconds and giv
184. ces should be performed at the intervals specified to help ensure the safety dependability and emission control performance of your vehicle Your dealer retailer can assist you with these checks and services Be sure any necessary repairs are completed at once Whenever any fluids or lubricants are added to your vehicle make sure they are the proper ones as shown in Recommended Fluids and Lubricants on page 6 11 At Each Fuel Fill It is important to perform these underhood checks at each fuel fill Engine Oil Level Check Notice It is important to check the engine oil regularly and keep it at the proper level Failure to keep the engine oil at the proper level can cause damage to the engine not covered by your warranty Check the engine oil level and add the proper oil if necessary See Engine Oil on page 5 16 Engine Coolant Level Check Check the engine coolant level and add DEX COOL coolant mixture if necessary See Engine Coolant on page 5 27 Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary At Least Once a Month Tire Inflation Check Inspect your vehicle s tires and make sure they are inflated to the correct pressures Do not forget to check the spare tire See Inflation Tire Pressure on page 5 67 Check to make sure the spare tire is stored securely See Changing a Flat Tire on page 5 102 Tir
185. chdesaindtad set e ee udeae 3 22 Antenna Backglass 0 0ceeceeeeeeeeeeeeeeeees 3 108 Antenna XM Satellite Radio Antenna SV SUOMI eenen a eacese neaatee 3 108 Antilock Brake System ABS eeeeeeeeeeeees 4 4 Antilock Brake System Warning Light 3 38 Appearance Care Aluminum or Chrome Plated Wheels 5 117 Care of Safety Belts cceeeeeeeeeeeee es 5 114 Chemical Paint Spotting eeeeeeeeeeee ees 5 119 Cleaning Exterior Lamps Lenses 4 5 116 Fabrici Carpet sictccccnctsiecccnedd aecegeeseeecceinenuen 5 113 Finish Gare sieisen ii a ESEA 5 116 Finish Damage sccciiccncaticteccaracthacuerce seers 5 118 Instrument Panel Vinyl and Other Plastic Surfaces cceeseeeeeeeeeee eee as 5 114 Interior Cleaning csnisisssii nen suninri 5 111 Leather sqiceiiidi sist t E eee 5 113 Sheet Metal Damage eeeeeeeeeeeeeeeees 5 118 Speaker CoverS ccseeeeeeeceeeeeeeeeeeeeeeees 5 114 TES oraaa a AE wanna nines 5 118 Underbody Maintenance 5 119 Vehicle Care Appearance Materials 5 119 Washing Your Vehicle ceeeeeeeeeeeee eee es 5 115 Weatthersttips s icccicetecs deccsccs ceiwiebay eee tneeelene 5 115 Windshield and Wiper Blades 5 5 117 Wood Panels sitentsachenadedsecatcntiomntiacnandiens 5 114 Appointments Scheduling Service 7 9 ASI AY
186. cification code molded onto the sidewall GM s TPC specifications meet or exceed all federal safety guidelines Tire Size The following illustration shows an example of a typical passenger vehicle tire size P225 60R16 97S IT HIT A Passenger P Metric Tire The United States version of a metric tire sizing system The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U S Tire and Rim Association B Tire Width The three digit number indicates the tire section width in millimeters from sidewall to sidewall 5 63 C Aspect Ratio A two digit number that indicates the tire height to width measurements For example if the tire size aspect ratio is 60 as shown in item C of the illustration it would mean that the tire s sidewall is 60 percent as high as it is wide D Construction Code A letter code is used to indicate the type of ply construction in the tire The letter R means radial ply construction the letter D means diagonal or bias ply construction and the letter B means belted bias ply construction E Rim Diameter Diameter of the wheel in inches F Service Description These characters represent the load range and speed rating of the tire The load index represents the load carry capacity a tire is certified to carry The load index can range from 1 to 279 The speed rating is the maximum speed a tire is certified to carry a
187. ck 55 5 126 Underhood Fuse Block eeeeeeeeee eee ees 5 122 Windshield Wiper Fuses aseeseen 5 121 Engine Air Cleaner Filter ccceeeeeeeeeeeeeeeeeeeeeeees 5 21 Check and Service Engine Soon Light 3 40 COGAN saesae seaweed ae cetabenstad wpa aA 5 27 Coolant Heati sucrar aani 2 36 Coolant Temperature Gage eeceeeeeeeeeee 3 39 Coolant Temperature Warning Light 3 39 Drive Belt Routing ceceeeeeeeeeeeeeereeeee 6 14 Engine Compartment Overview 6 eeee 5 14 Exhaust sinchcitAanedds oh yebidsdtamiocatdacianetdesecucteaey 2 47 o scsloteactecldesteloulsseiesaee E aeieie 5 16 Oil Life System 2 0 0 cece eeeeeeeeeeee eee eee eens 5 19 Oil Pressure Gage ceeeeeeeeeeeeeeece eee eeee 3 44 Overheated Protection Operating Mode 5 32 Overheatihgi 2 ics ideo cchcenecthemede eni eann 5 30 Speed Limiter cccicchsiseuadiseesnnatiees ivi cdeys 3 32 Staring eteen tea metemasen said ideadueanetes 2 34 Entry LIQWting sie is agestisctiicentincddensadne castes i 3 19 Event Data Recorders 0 0 00 ceceeeeeeeeeeeee eee eeeees 7 17 Extender Safety Belt cceeeeeeeeeeeeeee teen ees 1 31 Exterior Lighting Battery Saver eeeeeeeees 3 19 Filter Engine Air Cleaner a 5 21 FINISH Damage esis idcnctasettenctapeneceawoeadannseceens 5 118 Flashers Hazard Warning 0 eceeeeeeeeeeeeees 3 6 FlaSh to PaS
188. cked into position Safety Belt Pretensioners Your vehicle has safety belt pretensioners for front outboard occupants Although you cannot see them they are part of the safety belt assembly They can help tighten the safety belts during the early stages of a moderate to severe frontal and near frontal crash if the threshold conditions for pretensioner activation are met And if your vehicle has side impact airbags safety belt pretensioners can help tighten the safety belts in a side crash Pretensioners work only once If they activate in a crash you will need to get new ones and probably other new parts for your safety belt system See Replacing Restraint System Parts After a Crash on page 1 71 1 27 Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults When installed on a shoulder belt the comfort guide positions the belt away from the neck and head There is one guide for each outboard passenger position in the rear seat Here is how to install a comfort guide to the safety belt 1 28 1 Pull the elastic cord out from between the edge of the seatback and the interior body to remove the guide from its storage clip 2 Place the guide over the belt and insert the 3 Be sure that the belt is not twisted and it lies flat two edges of the belt into the slots of the guide The elastic cord
189. clearcoat paint finish the clearcoat gives more depth and gloss to the colored basecoat Always use waxes and polishes that are non abrasive and made for a basecoat clearcoat paint finish Notice Machine compounding or aggressive polishing on a basecoat clearcoat paint finish may damage it Use only non abrasive waxes and polishes that are made for a basecoat clearcoat paint finish on your vehicle 5 116 Foreign materials such as calcium chloride and other salts ice melting agents road oil and tar tree sap bird droppings chemicals from industrial chimneys etc can damage your vehicle s finish if they remain on painted surfaces Wash the vehicle as soon as possible If necessary use non abrasive cleaners that are marked safe for painted surfaces to remove foreign matter Exterior painted surfaces are subject to aging weather and chemical fallout that can take their toll over a period of years You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster Washing with water is all that is usually needed However you may use chrome polish on chrome or stainless steel trim if necessary Use special care with aluminum trim To avoid damaging protective trim never use auto or chrome polish steam or caustic soap to clean aluminum A coating of wax rubbed to high
190. comes separated from the hitch Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer Follow the manufacturer s recommendation for attaching safety chains and do not attach them to the bumper Always leave just enough slack so you can turn with your rig And never allow safety chains to drag on the ground Trailer Brakes Does your trailer have its own brakes Be sure to read and follow the instructions for the trailer brakes so you will be able to install adjust and maintain them properly Because you have anti lock brakes do not try to tap into your vehicle s brake system If you do both brake systems will not work well or at all Trailer Wiring Harness All of the electrical circuits required for your trailer lighting system can be accessed at the driver s side rear lamp connector This connector is located under the carpet on the rear corner of the trunk compartment Driving with a Trailer Towing a trailer requires a certain amount of experience Before setting out for the open road you will want to get to know your rig Acquaint yourself with the feel of handling and braking with the added weight of the trailer And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself Before you start check all trailer hitch parts and attachments safety chains electrical connector lamps ti
191. corrosion material to parts repaired or replaced to restore corrosion protection Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty Finish Damage Any stone chips fractures or deep scratches in the finish should be repaired right away Bare metal will corrode quickly and may develop into major repair expense Minor chips and scratches can be repaired with touch up materials available from your dealer retailer Larger areas of finish damage can be corrected in your dealer s retailer s body and paint shop Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody If these are not removed corrosion and rust can develop on the underbody parts such as fuel lines frame floor pan and exhaust system even though they have corrosion protection At least every spring flush these materials from the underbody with plain water Clean any areas where mud and debris can collect Dirt packed in close areas of the frame should be loosened before being flushed Your dealer retailer or an underbody car washing system can do this for you Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout Airborne pollutants can fall upon and attack painted surfaces on the vehicle This damage can take two forms blotchy ring shaped discolorations and small irregular dark spots etched into the pa
192. crease engine idle speed to generate more power whenever needed It can temporarily reduce the power demands of some accessories Normally these actions occur in steps or levels without being noticeable In rare cases at the highest levels of corrective action this action may be noticeable to the driver If so a Driver Information Center DIC message might be displayed such as Battery Saver Active or Service Battery Charging System If this message is displayed it is recommended that the driver reduce the electrical loads as much as possible See DIC Warnings and Messages on page 3 54 Battery Run Down Protection Your vehicle has a feature to help prevent battery drain if accessory lamps are left on or something is left plugged into the accessory power outlet or cigarette lighter if the vehicle has one If accessory lamps such as the vanity mirror cargo reading console or glove box are left on they automatically time out after about 20 minutes To reset the battery protection all of the above lamps must be turned off or the ignition must be in the ACC ACCESSORY position Accessory Power Outlet s Accessory power outlets can be used to connect auxiliary electrical equipment such as a cellular telephone or CB radio There are three accessory power outlets There is an outlet located in the front storage area below the climate control system one inside the center console storage bin and one on the rear of the center
193. cseeseseseseeeeeees 3 105 Security Light cece tsetse eee eee eeeeeees 3 45 Navigation Radio System 0 ccccccceeeeeeeeees 3 106 FOG Lamp Light eset eee tte ee tees 3 45 Theft Deterrent Feature ee 3 106 Lights On Reminder cssceeseeeeeeeee 3 46 Audio Steering Wheel Controls c0cceeeee 3 106 Cruise Control Light seeeeeeeiieeen 3 46 Radio Reception iceaisacisisasnisvaniietenceasaaatentars 3 107 Highbeam On Light 1 2 1 3 46 Backglass Antenna c cscectcsteicsnsecsanavuassninsnans 3 108 FUG Gage scsieeeaceveceenlonscosestedbneda e E Raa 3 46 XM Satellite Radio Antenna System 3 108 4 NOTES 3 3 Instrument Panel Overview 3 4 The main components of the instrument panel are the following A B C Air Outlets See Outlet Adjustment on page 3 27 Driver Information Center DIC Buttons See Driver Information Center DIC on page 3 47 Instrument Panel Brightness Control See Instrument Panel Brightness on page 3 19 Turn Signal Multifunction Lever See Turn Signal Multifunction Lever on page 3 7 Instrument Panel Cluster See Instrument Panel Cluster on page 3 30 Windshield Wiper Lever See Windshield Wipers on page 3 9 Traction Control System TCS Disable Button See Traction Control System TCS on page 4 6 Analog Clock See Analog Clock on page 3 22 Hazard Warning Flasher Button See Hazard Warning
194. d Compensated Volume setting OFF Low Med or High to select the level of radio volume compensation The display times out after approximately 10 seconds Each higher setting allows for more radio volume compensation at faster vehicle speeds 3 82 Noise Compensation Technology If your vehicle has the Radio with DVD Audio HDD and USB it includes Bose AudioPilot noise compensation technology When turned on AudioPilot continuously adjusts the audio system equalization to compensate for background noise This feature is most effective at lower radio volume settings where background noise can affect how well you hear the music being played through your vehicle s audio system At higher volume settings where the music is much louder than the background noise there might be little or no adjustments by AudioPilot For additional information on AudioPilot visit www bose com audiopilot To activate AudioPilot 1 Press the CONFIG button to display the radio setup menu 2 Press the pushbutton under the AUTO VOL label on the radio display 3 Press either the On or Off label located under the AUTO VOL display to turn this feature on or off The display times out after approximately 10 seconds Finding a Station TUNE TONE Turn to select different radio stations within a selected band FM AM Press to switch between FM and AM radio bands Ki SEEK D Press the arrows to go to the previous or to the next r
195. d Miles Kilometers 40000 g0 000 120 000 160 000 200 000 240 000 Inspect fuel system for damage or leaks Inspect exhaust system for loose or damaged components Replace engine air cleaner filter See Engine Air Cleaner Filter on page 5 21 Replace passenger compartment air filter See footnote g Change automatic transmission fluid and filter severe service See footnote h Change automatic transmission fluid and filter normal service Replace spark plugs An Emission Control Service Additional Required Services cont d eee 25 000 50 000 75 000 100 000 125 000 150 000 Service and Miles Kilometers 40 000 80 000 120 000 160 000 200 000 240 000 Engine cooling system service or every five years whichever occurs first An Emission Control Service See footnote i Inspect engine accessory drive belt An Emission Control Service See footnote m If using DOT 4 brake fluid change brake fluid at a regular maintenance service every two years See footnote j Maintenance Footnotes a Visually inspect brake lines and hoses for proper hook up binding leaks cracks chafing etc Inspect disc brake pads for wear and rotors for surface condition Inspect other brake parts including calipers parking brake etc b Visually inspect front and rear suspension and steering system for damaged loose or missing parts or signs of wear In
196. d say OnStar to enter OnStar mode See the OnStar System on page 2 53 in this manual for more information Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers vehicle convenience accessories and external electronic devices are plugged into the accessory power outlet If there is interference or static unplug the item from the accessory power outlet AM The range for most AM stations is greater than for FM especially at night The longer range can cause station frequencies to interfere with each other For better radio reception most AM radio stations boost the power levels during the day and then reduce these levels during the night Static can also occur when things like storms and power lines interfere with radio reception When this happens try reducing the treble on your radio FM Stereo FM stereo gives the best sound but FM signals reach only about 10 to 40 miles 16 to 65 km Tall buildings or hills can interfere with FM signals causing the sound to fade in and out XM Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast to coast in the 48 contiguous United States and in Canada Just as with FM tall buildings or hills can interfere with satellite radio signals causing the sound to fade in and out In addition traveling or standing under heavy foliage bridges garages or tunnels
197. d until the fifth press of the windshield washer button The headlamps must be on to be washed If the headlamps are off only the windshield will be washed when the washer button is pressed If the washer fluid is low the headlamp washers will not work See Windshield Washer on page 3 11 for more information Cruise Control A CAUTION Cruise control can be dangerous where you cannot drive safely at a steady speed So do not use your cruise control on winding roads or in heavy traffic Cruise control can be dangerous on slippery roads On such roads fast changes in tire traction can cause excessive wheel slip and you could lose control Do not use cruise control on slippery roads With cruise control a speed of about 25 mph 40 km h or more can be maintained without keeping your foot on the accelerator This can really help on long trips Cruise control does not work at speeds below about 25 mph 40 km h When the brakes are applied the cruise control turns off 3 13 If your vehicle has the StabiliTrak system and begins to limit wheel spin while you are using cruise control the cruise control will automatically disengage See StabiliTrak System on page 4 8 When road conditions allow you to safely use it again the cruise control can be turned back on The cruise control buttons are located on the left side of the steering wheel On Off Press button to activate and turn off the system
198. e GOMPACK s mccanast yescctncs Soenhsaneetapehccnenaentawned 5 111 IStAllING ts 22eveees silae E a E Geeeeedd 5 105 REMOVING recenp ecnasacind ve nawes tatdedcsbidaeesceanun 5 104 SLOPING sneh panna E gue tec pamceeiecaeg 5 110 Specifications Capacities ceeeeeeeeeeeee ees 5 128 Speedometer cccceeeeceeeeeeeeeeeeeeeeeneeaeeaeeaes 3 31 Split Folding Rear Seat 1 11 StabiliTrak System ccccccccceeeeeeeceeeeeeeeneaeees 4 8 StabiliTrak TCS Warning Light 00 00 3 38 Start Vehicle Remote ccccceccceeeeeeeeeeeees 2 14 Starting the Engine ceceeeeeeeeeeeeeeeeeeee tenes 2 34 Steering sede Ga vincwens nanira E 4 9 Steering Wheel Controls Audio 655 3 106 Steering Wheel Power Tilt Wheel and Telescopic Steering Column 0 eeeeeeeeeee 3 7 Steering Wheel Tilt and Telescopic 00 3 6 Storage Areas Center Console Storage Area ecceeeeeeneees 2 61 Convenience Net cceeeeeeeeeeeeeee eee eee eee 2 62 Cupholder S ssscses este litiresastassdeniiendnaledesevins 2 61 GIOVE BOX esccac checectacscgeattesseiacnesanae tea cecukh 2 61 Instrument Panel Storage Area eeeeeeee 2 61 Stuck in Sand Mud Ice or Snow 0065 4 21 SUM VISOMS lt ccsntscsisacnsdecetagenctmedemesnaadacievecnnedicnd 2 26 SUNMMOOP erreian orana EE TETES AEE E anaa 2 62 11 Tachometer j cscstrseiciivecediorieninadhuestieti
199. e Here are a few of the valuable tools and services you will have access to My Showroom Find and save information on vehicles and current offers in your area My Dealers Retailers Save details such as address and phone number for each of your preferred GM Dealers or Retailers My Driveway Receive service reminders and helpful advice on owning and maintaining your vehicle My Preferences Manage your profile subscribe to E News and use tools and forms with greater ease To sign up to My GM Canada visit the My GM Canada section within www gmcanada com Customer Assistance for Text Telephone TTY Users To assist customers who are deaf hard of hearing or speech impaired and who use Text Telephones TTYs Cadillac has TTY equipment available at its Customer Assistance Center Any TTY user can communicate with Cadillac by dialing 1 800 833 CMCC 2622 TTY users in Canada can dial 1 800 263 3830 Customer Assistance Offices Cadillac encourages customers to call the toll free number for assistance However if a customer wishes to write or e mail Cadillac the letter should be addressed to United States Customer Assistance Cadillac Customer Assistance Center Cadillac Motor Car Division P O Box 33169 Detroit MI 48232 5169 www Cadillac com 1 800 458 8006 1 800 833 2622 For Text Telephone devices TTYs Roadside Assistance 1 800 882 1112 Fax Number 313 381 0022 From Puerto Rico 1
200. e Cranking the engine for long periods of time by returning the key to the START position immediately after cranking has ended can overheat warranty 2 35 Engine Coolant Heater The engine coolant heater if available can help in cold weather conditions at or below 0 F 18 C for easier starting and better fuel economy during engine warm up Plug in the coolant heater at least four hours before starting your vehicle An internal thermostat in the plug end of the cord may exist which will prevent engine coolant heater operation at temperatures above 0 F 18 C To Use the Engine Coolant Heater 1 Turn off the engine 2 Open the hood and unwrap the electrical cord The cord is located in the engine compartment on the passenger side of the vehicle in front of the fuse block Remove the plastic cap to access the plug 3 Plug it into a normal grounded 110 volt AC outlet 2 36 A CAUTION Plugging the cord into an ungrounded outlet could cause an electrical shock Also the wrong kind of extension cord could overheat and cause a fire You could be seriously injured Plug the cord into a properly grounded three prong 110 volt AC outlet If the cord will not reach use a heavy duty three prong extension cord rated for at least 15 amps 4 Before starting the engine be sure to unplug and store the cord as it was before to keep it away from moving engine parts If you do not it could be damaged How lon
201. e see Servicing Your Airbag Equipped Vehicle on page 1 68 Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker If the wiper motor overheats due to heavy snow the wipers will stop until the motor cools and will then restart 5 121 Power Windows and Other Power Options Circuit breakers in the fuse block protect the power windows and other power accessories When the current load is too heavy the circuit breaker opens and closes protecting the circuit until the problem is fixed or goes away Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers This greatly reduces the chance of fires caused by electrical problems Look at the silver colored band inside the fuse If the band is broken or melted replace the fuse Be sure you replace a bad fuse with a new one of the identical size and rating If you ever have a problem on the road and don t have a spare fuse you can borrow one that has the same amperage Just pick some feature of your vehicle that you can get along without like the radio or cigarette lighter and use its fuse if it is the correct amperage Replace it as soon as you can 5 122 Underhood Fuse Block The underhood fuse block is located on the passenger side of the engine compartment Lift the fuse block cover to access the fuses Notice Spilling liquid on an
202. e 1 42 Cigarette Lighter cceeeeeeeeeeeeeeeeeeeeeeeeeeee 3 22 Cleaning Aluminum or Chrome Plated Wheels 5 117 Exterior Lamps Lenses seeeeeeeeeeee ees 5 116 Fabric Garpet cesccacdt citcecescaycanedesamennotencsedtu 5 113 Finish Care scsineceescseshees cise vses selene nan ais 5 116 Instrument Panel Vinyl and Other Plastic Surfaces ceesre cence ty 5 114 nenon scart tates e ENE 5 111 Leather ireira e a AE 5 113 Speaker Covers cccecceeeeeeneeeeeeeeeeaeeeees 5 114 WANS ee scce cease a E E 5 118 Underbody Maintenance ceeeeeeeeee 5 119 Washing Your Vehicle eeeeeeeeeeeee eee 5 115 Weatherstrips cicsasstasoncariacdtiedhecsnihnsesaantendnes 5 115 Windshield and Wiper Blades 5 117 Wood Panels seresa aait 5 114 Climate Control System Air Filter Passenger Compartment 3 28 Dal sexiest ciastenctinentaided siicdesitenebn i eieeeaas 3 23 Outlet Adjustment ceeeeeeeeee eee eeee eee eeaes 3 27 ClOGK sist ctesiec a a attetacctinneanateursannaet nce 3 22 Clutch Ay drauli seresa iasta 5 26 Collision Damage Repair eceeseeeeeeeeeeeeenes 7 11 Compact Spare Tire ccceeeeeeeeeeeeeeee een ees 5 111 COMPASS esocu eea e raae AEE EAEE 3 52 Competitive Driving ccceeeeeeeeeeeeeeeeeee eee eeaes 4 14 Compressor Kit Tire Sealant 5 5 85 5 93 Control of a Vehicle ce
203. e Break In Notice Your vehicle does not need an elaborate break in But it will perform better in the long run if you follow these guidelines for the first 500 miles 805 km e Do not drive at any one constant speed fast or slow e Do not exceed 70 mph 113 km h e Do not make full throttle starts also refrain from using the full throttle while driving Avoid downshifting to brake or slow the vehicle If these procedures are not followed the engine axle or other parts could be damaged Avoid making hard stops for the first 200 miles 322 km or so During this time the new brake linings are not yet broken in Hard stops with new linings can mean premature wear and earlier replacement Follow this break in guideline every time you get new linings Do not tow a trailer during break in See Towing a Trailer on page 4 29 for the trailer towing capabilities of your vehicle and more information Following break in engine speed and load can be gradually increased Ignition Positions Key Access The key can be turned to four different positions To shift out of PARK P ignition must be in the ON RUN or ACC ACCESSORY and the regular brake pedal must be applied 2 31 Notice Using a tool to force the key from its cylinder could cause damage or break the key Use the correct key and turn the key only with your hand Make sure the key is all the way in If it is and you have a manual transmission vehicle turn
204. e Ignition Positions Key Access on page 2 31 or Ignition Positions Keyless Access on page 2 33 for information on starting the vehicle Notice f you ever lock your keys in your vehicle you may have to damage the vehicle to get in Be sure you have spare keys In an emergency contact Roadside Assistance See Roadside Service on page 7 6 Remote Keyless Entry RKE System If the vehicle has the Remote Keyless Entry RKE system it operates on a radio frequency subject to Federal Communications Commission FCC Rules and with Industry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment At times you may notice a decrease in range This is normal for any RKE system If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work try this
205. e Wear Inspection Tire rotation may be required for high mileage highway drivers prior to the Engine Oil Life System service notification Check the tires for wear and if necessary rotate the tires See Tire Inspection and Rotation on page 5 75 At Least Once a Year Starter Switch Check A CAUTION 1 2 When you are doing this inspection the vehicle could move suddenly If the vehicle moves you or others could be injured Before you start be sure you have enough room around the vehicle Firmly apply both the parking brake and the regular brake See Parking Brake on page 2 43 Do not use the accelerator pedal and be ready to turn off the engine immediately if it starts On automatic transmission vehicles try to start the engine in each gear The vehicle should start only in PARK P or NEUTRAL N If the vehicle starts in any other position contact your dealer retailer for service On manual transmission vehicles put the shift lever in NEUTRAL push the clutch pedal down halfway and try to start the engine The vehicle should start only when the clutch pedal is pushed down all the way to the floor If the vehicle starts when the clutch pedal is not pushed all the way down contact your dealer retailer for service Automatic Transmission Shift Lock Control System Check Z CAUTION When you are doing this inspection the vehicle could move suddenly If the vehicle moves you or others could be inju
206. e a TPMS sensor The DIC message should go off once you re install the road tire containing the TPMS sensor e The TPMS sensor matching process was not done or not completed successfully after rotating the vehicle s tires The DIC message should go off after successfully completing the sensor matching process See TPMS Sensor Matching Process later in this section One or more TPMS sensors are missing or damaged The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully See your dealer retailer for service e Replacement tires or wheels do not match your vehicle s original equipment tires or wheels Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly See Buying New Tires on page 5 77 e Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction If the TPMS is not functioning it cannot detect or signal a low tire condition See your dealer retailer for service if the TPMS malfunction light and DIC message comes on and stays on TPMS Sensor Matching Process Each TPMS sensor has a unique identification code Any time you replace one or more of the TPMS sensors or rotate your vehicle s tires the identification codes need to be matched to the new tire wheel position The sens
207. e of the following e Check the distance You may be too far from your vehicle You may need to stand closer during rainy or snowy weather e Check the location Other vehicles or objects may be blocking the signal Take a few steps to the left or right hold the transmitter higher and try again e Check to determine if battery replacement is necessary See Battery Replacement under Keyless Access System Operation on page 2 9 e Check to make sure that an electronic device such as a cellular phone or lap top computer is not causing interference e If you are still having trouble see your dealer retailer or a qualified technician for service Remote Keyless Entry RKE System Operation The Remote Keyless Entry RKE transmitter functions including lock unlock remote trunk release and vehicle locator panic alarm will work up to 65 feet 20 m away There are other conditions which can affect the performance of the transmitter See Remote Keyless Entry RKE System on page 2 5 Lock Press to lock all the doors If enabled through the Driver Information Center DIC the parking lamps may flash once to indicate locking has occurred or the horn may chirp when is pressed again within five seconds from the previous press of the lock button See DIC Vehicle Customization on page 3 68 for additional information n Unlock Press m to unlock the driver s door If m is pressed again within five seconds all
208. e status of the vehicle has changed and that some action may be needed by the driver to correct the condition Multiple messages may appear one after another Some messages may not require immediate action but you can press any of the DIC buttons on the instrument panel to acknowledge that you received the messages and to clear them from the display Some messages cannot be cleared from the DIC display because they are more urgent These messages require action before they can be cleared You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear not correct the problem The following are the possible messages that can be displayed and some information about them Accessory Mode Active If your vehicle has the keyless access system this message displays when the accessory mode is active See Ignition Positions Key Access on page 2 31 or Ignition Positions Keyless Access on page 2 33 for more information AFL Adaptive Forward Lighting Lamps Need Service This message displays when the Adaptive Forward Lighting AFL system is disabled and needs service See your dealer retailer See Adaptive Forward Lighting System on page 3 18 for more information All Wheel Drive Off If your vehicle has the All Wheel Drive AWD system this message displays when there is a temporary condition making the AWD system unavailable Your vehicle will run i
209. e the command ONSTAR to activate the OnStar Hands Free Calling On some vehicles the mute button can be used to dial numbers into voicemail systems or to dial phone extensions See the OnStar Owner s Guide for more information How OnStar Service Works Your vehicle s OnStar system has the capability of recording and transmitting vehicle information This information is automatically sent to an OnStar Call Center at the time of an OnStar button press Emergency button press or if your airbags or AACN system deploys The vehicle information usually includes your GPS location and in the event of a crash additional information regarding the accident that your vehicle has been involved in e g the direction from which your vehicle was hit When you use the Virtual Advisor feature of OnStar Hands Free Calling your vehicle also sends OnStar your GPS location so that we can provide you with location based services 2 55 OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage network capacity and reception when the service is needed and technology that is compatible with the OnStar service Not all services are available everywhere particularly in remote or enclosed areas or at all times Loc
210. e them last longer seal better and not stick or squeak g If you drive regularly under dusty conditions the filter may require replacement more often h Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions In heavy city traffic where the outside temperature regularly reaches 90 F 32 C or higher In hilly or mountainous terrain When doing frequent trailer towing Uses such as high performance operation i Drain flush and refill cooling system This service can be complex you should have your dealer retailer perform this service See Engine Coolant on page 5 27 for what to use Inspect hoses Clean radiator condenser pressure cap and filler neck Pressure test the cooling system and pressure cap j If using DOT 4 brake fluid only Drain flush and refill brake hydraulic system at a regular maintenance service every two years This service can be complex you should have your dealer retailer perform this service See Brakes on page 5 40 k A fluid loss in any vehicle system could indicate a problem Have the system inspected and repaired and the fluid level checked Add fluid if needed I If you drive regularly under dusty conditions inspect the filter at each engine oil change m Visually inspect belt for fraying excessive cracks or obvious damage Replace belt if necessary Owner Checks and Services These owner checks and servi
211. e to the engine transmission exhaust intake or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria TPC can affect your vehicle s emission controls and can cause this light to come on Modifications to these systems could lead to costly repairs not covered by your warranty This could also result in a failure to pass a required Emission Inspection Maintenance test See Accessories and Modifications on page 5 3 This light comes on as a check to show it is working when the ignition is turned ON RUN but the engine is not running lf the light does not come on have it repaired This light also comes on during a malfunction in one of two ways e Light Flashing A misfire condition has been detected A misfire increases vehicle emissions and could damage the emission control system on your vehicle Diagnosis and service might be required e Light On Steady An emission control system malfunction has been detected on your vehicle Diagnosis and service might be required 3 41 If the Light is Flashing The following can prevent more serious damage to your vehicle e Reduce vehicle speed e Avoid hard accelerations e Avoid steep uphill grades e If you are towing a trailer reduce the amount of cargo being hauled as soon as it is possible If the light stops flashing and remains on steady see If the Light Is On Steady following I
212. e warning lights and gages could also save you or others from injury Warning lights come on when there may be or is a problem with one of your vehicle s functions As you will see in the details on the next few pages some warning lights come on briefly when you start the engine just to let you know they are working If you are familiar with this section you should not be alarmed when this happens Gages can indicate when there may be or is a problem with one of your vehicle s functions Often gages and warning lights work together to let you know when there is a problem with your vehicle When one of the warning lights comes on and stays on while you are driving or when one of the gages shows there may be a problem check the section that tells you what to do about it Waiting to do repairs can be costly and even dangerous So please get to know your warning lights and gages They are a big help Your vehicle also has a Driver Information Center DIC that works along with the warning lights and gages See Driver Information Center DIC on page 3 47 for more information 3 29 Instrument Panel Cluster The instrument panel cluster is designed to let you know at a glance how your vehicle is running You will know how fast you are going how much fuel you are using and many of the other things you will need to know to drive safely and economically United States Automatic Cluster shown Canada similar 3 30
213. ection appears in the display screen Changing the mode cancels the automatic operation and the system goes into manual mode Press AUTO to return to automatic operation The outboard air outlets always receive some airflow in every mode except defrost See Outlet Adjustment on page 3 27 to change this airflow from the outboard outlets 74 Vent This mode directs air to the instrument panel outlets 7 Bi Level This mode splits the air between the instrument panel outlets and the floor outlets In automatic operation cooler air is directed to the upper outlets and warmer air to the floor outlets Vad Floor This mode directs most of the air to the floor outlets with some air directed to the outboard outlets and a little air directed to the windshield The mode buttons can also be used to select the defog and defrost modes Information on defogging and defrosting can be found later in this section EE Fan Press the or buttons to increase or decrease the fan speed Pressing either button cancels automatic operation and the system goes into manual mode Press AUTO to return to automatic operation The blower may reduce during an Onstar session to limit background noise If the airflow seems low when the fan speed is at the highest setting the passenger compartment air filter might need to be replaced For more information see Passenger Compartment Air Filter on page 3 28 and Scheduled Maintenance on page 6 4
214. ects Avoid jerky or sudden maneuvers Signal well in advance 4 33 Turn Signals When Towing a Trailer When you tow a trailer your vehicle may need a different turn signal flasher and or extra wiring Check with your dealer retailer The arrows on your instrument panel will flash whenever you signal a turn or lane change Properly hooked up the trailer lamps will also flash telling other drivers you are about to turn change lanes or stop When towing a trailer the arrows on your instrument panel will flash for turns even if the bulbs on the trailer are burned out Thus you may think drivers behind you are seeing your signal when they are not It is important to check occasionally to be sure the trailer bulbs are still working Your vehicle has bulb warning lights When you plug a trailer lighting system into your vehicle s lighting system its bulb warning lights may not let you know if one of your lamps goes out So when you have a trailer lighting system plugged in be sure to check your vehicle and trailer lamps from time to time to be sure they are all working Once you disconnect the trailer lamps the bulb warning lights again can tell you if one of your vehicle lamps is out 4 34 Driving On Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade If you do not shift down you might have to use your brakes so much that they would get hot and no longer work well On a long
215. ed may cause damage to the seat or the safety belts Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat 2 Fold the seatback down This allows direct access to the trunk See Trunk on page 2 20 for more information To return the seatback to the upright position A CAUTION If the seatback is not locked it could move forward in a sudden stop or crash That could cause injury to the person sitting there Always push and pull on the seatback to be sure it is locked 1 Lift the seatback up and push it back into place 2 Make sure the seatback is locked into place by pushing and pulling on it 3 Repeat Steps 1 and 3 for the other seatback When the seatback is not in use it should be kept in the upright locked position Safety Belts Safety Belts They Are for Everyone This part of the manual tells you how to use safety belts properly It also tells you some things you should not do with safety belts A CAUTION Do not let anyone ride where he or she cannot wear a Safety belt properly If you are ina crash and you are not wearing a safety belt your injuries can be much worse You can hit things inside the vehicle harder or be ejected from it and be seriously injured or killed In the same crash you might not be if you are buckled up Always fasten your safety belt and check that your passenger s are restrained properly too A CAUTION I
216. ed seating positions Outward Facing Sidewall The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle The side of the tire that contains a whitewall bears white lettering or bears manufacturer brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire Passenger P Metric Tire A tire used on passenger cars and some light duty trucks and multipurpose vehicles Recommended Inflation Pressure Vehicle manufacturer s recommended tire inflation pressure as shown on the tire placard See Inflation Tire Pressure on page 5 67 and Loading Your Vehicle on page 4 22 Radial Ply Tire A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread Rim A metal support for a tire and upon which the tire beads are seated Sidewall The portion of a tire between the tread and the bead 5 66 Speed Rating An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate Traction The friction between the tire and the road surface The amount of grip provided Tread The portion of a tire that comes into contact with the road Treadwear Indicators Narrow bands sometimes called wear bars that show across the tread of a tire when only 1 16 inch 1 6 mm of tread remains See When It Is Time for New Tires on page 5 76 UTQGS Uni
217. ed to turn off the right front passenger s frontal airbag and seat mounted side impact airbag under certain conditions See Passenger Sensing System on page 1 64 and Passenger Airbag Status Indicator on page 3 34 for more information on this including important safety information 1 51 A label on your sun visor says Never put a rear facing child seat in the front This is because the risk to the rear facing child is so great if the airbag deploys A CAUTION A child in a rear facing child restraint can be seriously injured or killed if the right front passenger s airbag inflates This is because the back of the rear facing child restraint would be very close to the inflating airbag Even though the passenger sensing system is designed to turn off the right front passenger s frontal airbag if the system detects a rear facing child restraint no system is fail safe and no one can guarantee that an airbag will not deploy under some unusual circumstance even though it is turned off We recommend that rear facing child restraints be secured in a rear seat even if the airbag is off CAUTION Continued 1 52 CAUTION Continued If you secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go It is better to secure the child restraint in a rear seat See Passenger Sensing System on page 1 64 for additional information If your child
218. eeccneeeententimaddes beh aed 4 14 Driving in Rain and on Wet Roads 4 15 Before Leaving on a Long Trip 0e 4 16 Highway Hypnosis cceeeeeeeeeeeeeee eee eeeees 4 16 Hill and Mountain Roads ceeeeeeeeee eee 4 17 Winter Driving siccctiiscnetess ciiecascxetdincinedianea deed 4 18 If Your Vehicle is Stuck in Sand Mud Ice Or SNOW resson EE E REEE AE 4 21 Rocking Your Vehicle to Get It Out 4 22 Loading Your Vehicle eeeeeeeeeeeeeeee 4 22 TOWING 3220225 cesses ete Mae ee 4 27 Towing Your Vehicle ceceeeeeeeeeee eee ee eens 4 27 Recreational Vehicle Towing eeeeeeeeee 4 27 TOWING a Trailer messege onr biases 4 29 Your Driving the Road and Your Vehicle Defensive Driving Defensive driving means always expect the unexpected The first step in driving defensively is to wear your safety belt See Safety Belts They Are for Everyone on page 1 12 A CAUTION Assume that other road users pedestrians bicyclists and other drivers are going to be careless and make mistakes Anticipate what they might do and be ready In addition e Allow enough following distance between you and the driver in front of you e Focus on the task of driving Driver distraction can cause collisions resulting in injury or possible death These simple defensive driving techniques could save your life Drunk Driving A
219. eed reaches 5 mph 8 km The doors will automatically unlock when the ignition is turned off and the key is removed from the ignition If someone needs to exit the vehicle once the doors are locked have that person use the manual lever or power door lock switch When the door is closed again it will not lock automatically Use the manual lever or the power door lock switch to lock the door The power door locks can be programmed through prompts displayed on the Driver Information Center DIC These prompts allow you to choose various lock and unlock settings For more information on programming see DIC Vehicle Customization on page 3 68 Rear Door Security Locks Your vehicle has rear door security locks These prevent passengers from opening the rear doors from the inside i The rear door security locks are located on the inside edge of each rear door The rear doors must be open to access them The label showing lock and unlock positions is located near the lock Lock Label shown To set the locks do the following 1 Insert the key into the security lock slot and turn it so the slot is in the horizontal position 2 Close the door When you want to open a rear door when the security lock is on do the following 1 Unlock the door using the Remote Keyless Entry RKE or Keyless Access System transmitter if the vehicle has one the power door lock switch or the rear door manual lock 2 Open the door from
220. eeddeew tee 3 31 Telescopic Steering Column Power Tilt Wheel 3 7 Telescopic Wheel c ceeeeneeeeeeeeeeereeeeeeeeeees 3 6 Theft Deterrent Radio ccccceeeeeeeeeeeeeees 3 106 Theft Deterrent System cceeeeeeeeeeeeeeeeneeee es 2 27 Theft Deterrent Systems ceeeeeeeeeeeeeeee ees 2 27 IMIMODINIZER gosni tesa ena E 2 28 Immobilizer Operation ceeeeeeeeee 2 28 2 30 Tilt WHGGM cs cavevetaseterczeasteciersSstam cabieeseeiceriiees 3 6 Tire Pressure WIQht c iceetciniiieredenianaedanaaes 3 40 TINGS eaea 5 59 Aluminum or Chrome Plated Wheels Cleaning arrean e cee eed 5 117 Buying New Tite wccscicsasestiatenenssnendenewseeeeeeis 5 77 E ar Un e E E mage ateacannnenneenees 5 83 Changing a Flat Tire sssssiiesceriiressnirsiensnsin 5 102 Cleaning e iirinn iendea 5 118 Compact Spare Tire sssssadn nararknvene tiea 5 111 Different SiZ 0 cece eee ee ec eeeeeeeceeeeeeeeeeeeees 5 79 High Speed Operation ccceeeeeeeneeeeeeeee ees 5 69 If a Tire Goes Flat zmeriame a 5 83 Inflation Tire Pressure eeeeeeeeeeeeee es 5 67 Inspection and Rotation 0 ceeeeeee ee ees 5 75 Installing the Spare Tire a an 5 105 Pressure Monitor Operation 0 eeeeeeees 5 71 12 Tires cont Pressure Monitor System eseeeeeeeeeee ees 5 70 Removing the Flat Tire a a 5 105 Removing the Spare Tire and Tools 5 104 Storing a
221. eeeeeeeeee eee eeee eee een eens 4 3 Convenience Net cccceeeeeeeeeeeeeee eee eeaeeaes 2 62 Coolant Engine Temperature Gage eceeeeeeeneee ees 3 39 Engine Temperature Warning Light 3 39 Heater Engine cccceceeeeeeeeeeeeeeeeeees 2 36 Surge Tank Pressure Cap cceeeeee 5 30 COMING SYSTEM anani sia tnana n ae enia 5 33 Cruise Control ei anteninin neiere annn iiia 3 13 Cruise Control Light cceceeeeeeeeeeeeeeea tenes 3 46 CUPNOIGEN S evscasccseades canst beectasaeedeenareipeleeesdeceee 2 61 Customer Assistance Information Courtesy Transportation cceeeeeeneeeeeeeee ees 7 9 Customer Assistance for Text Telephone TTY Users e eeeeeeeeeeeees 7 5 Customer Assistance Offices c eeeeeeeeees 7 5 Customer Assistance Information cont Customer Satisfaction Procedure 06 7 2 GM Mobility Reimbursement Program 7 6 Reporting Safety Defects to General Motors 7 15 Reporting Safety Defects to the Canadian Government 0eeeeeeeeeeeeees 7 14 Reporting Safety Defects to the United States Government eeeee 7 14 Roadside Service ccececeneeeeeeeeeeeneeeeenes 7 6 Service Publications Ordering Information 7 15 Daytime Running Lamps ceeeeeeeeeee eee eee 3 17 Defensive Driving ccceceeeeeeeeeeeeeeeeeeeeees 4 2 Delayed LOC
222. eeeeeeeeeeeeeteees 3 10 Windshield Washer eeeeeeeeeeeeeeeeee eens 3 11 Headlamp Washer c eceeeeeeeeeeeeeeeeeeees 3 13 Cruise Control igs scxisisisasescasdecaetestaciauiectesccess 3 13 FIGACIAMpPS serscccccta enen aE 3 16 Wiper Activated Headlamps 0 eeeeeeee ees 3 17 Headlamps on Reminder seeeeeeeeee ees 3 17 Daytime Running Lamps DRL 05 3 17 Adaptive Forward Lighting System 05 3 18 FOG LAMPS is siaentsccistseacan nesa aai 3 18 Exterior Lighting Battery Saver eee 3 19 Instrument Panel Brightness eeeeee 3 19 Entry LJAN ostessa aaa 3 19 Instrument Panel Parade DIMMING j wie sectpncticancnesevereevtressacioense 3 19 Reading Lamps sicsciccctacsecieedl eed decd ethos sise 3 20 Electric Power Management icce 3 20 Battery Run Down Protection 0 0e0 3 21 Accessory Power Outlet S e eeeeeeeeee ees 3 21 Ashtray s and Cigarette Lighter 3 22 Analog CIOCK sissors i atis inaout 3 22 Climate Controls 0 0 eee 3 23 Dual Climate Control System ee 3 23 Outlet Adjustment 0 2 eee 3 27 Passenger Compartment Air Filter 3 28 Warning Lights Gages and Indicators 3 29 Instrument Panel Cluster c eeeeeeeeeeeees 3 30 Speedometer and Odometer eeeeeeeeeee 3 31 Trip
223. ehicle A top tether anchor is built into the vehicle The top tether attachment B on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash Your child restraint may have a single tether A or a dual tether C Either will have a single attachment B to secure the top tether to the anchor 1 44 Some child restraints with top tethers are designed for use with or without the top tether being attached Others require the top tether always to be attached In Canada the law requires that forward facing child restraints have a top tether and that the tether be attached Be sure to read and follow the instructions for your child restraint If the child restraint does not have a top tether one can be obtained in kit form for many child restraints Ask the child restraint manufacturer whether or not a kit is available Lower Anchor and Top Tether Anchor Locations ahi Top Tether Anchor Seating positions with top tether anchors Lower Anchor Seating positions with two lower anchors Rear Seat To assist you in locating the lower anchors each seating position with lower anchors has two labels near the crease between the seatback and the seat cushion To assist you in locating a the top tether anchors the gar top tether anchor symbol n is located on the cover The top tether anch
224. ehicle to Get It Out on page 4 22 for more information See also Winter Driving on page 4 18 for information on using TCS when driving in snowy or icy conditions Press the TC Traction Control button located on the instrument panel to turn the system off TG If you press the TC button once the traction control system will turn off and the Traction Control System TCS Warning Light will flash Press the TC button again to turn the system back on Press and hold the TC button for five seconds or longer to turn the StabiliTrak system off The TCS StabiliTrak warning light will flash Press the TC button again to turn StabiliTrak back on For more information see StabiliTrak System on page 4 8 Adding non dealer non retailer accessories can affect your vehicle s performance See Accessories and Modifications on page 5 3 for more information Competitive Driving Mode Press the TC button quickly two times to select this optional handling mode The StabiliTrak Competitive Mode message displays in the Driver Information Center DIC While in the StabiliTrak Competitive Mode TCS does not operate and the TCS warning light comes on Adjust your driving accordingly Press the TC button again or turn the ignition to ACC ACCESSORY to turn the TCS back on and the TCS warning light off Notice When traction control is turned off or Competitive Driving Mode is active it is possible to lose traction If you atte
225. el HORN LO BEAM Low Beam without High Intensity WSW PUMP Windshield Washer Pump A Lemp tach lntenaity Diccharoe CAC CMPRSR Air Conditioning Compressor LT DRL HID Lamp High Intensity Discharge A C CMPRSR Air Conditioning Compressor FAN 1 Cooling Fan 1 ENG PUMP Engine Pump FOG LAMP Fog Lamps RT DRL Hio ge Dine Ranging Lar SPARE 5 125 Rear Compartment Fuse Block The rear compartment fuse block is located on top of the battery on the right side of the trunk The battery access door must be removed to access the fuse block LF FRT PWR SEAT RT FRT PWR SEAT PWR WNDW TRUNK RELSE FUEL BE UNLCK STOPILP RT POS REARFOG sult 2 E a ac H a REAR WNDW LT REAR WNDW TRUNK AELSE THEFT UGDO AUX OUTLET RVCSNSR RKE PASS KEY MDL CNSTRIVENT RT POS LP 5 126 Fuses Usage WRISEA gt RDO TAudio Sys eft Front Power Seat whi RDO Audio System Beer Right Front Power Seat TRUNK RELSE Trunk Release FUEL PUMP __ Fuel Pump PWR WNDW AIRBAG Airbag System PWR CLMN _ Power Steering Column Thart Deterent System TRUNK RELSE Trunk Release THEFT UGDO Universal Home Remote System SPARE FUEL PUMP _ Fuel Pump RKE Remote Keyless Entry System UNLCK PASS Key PASS Key Theft Deterrent STOP LP Stoplamp MDL Feature Module SPARE ei mariseat Mian RT POS LP Right Position Lamp STOP LP ___ Stoplamp REAR FOG Not Used RDO SPKR _ Audio Speakers LT POS L
226. elp avoid the damage When you read other manuals you might see CAUTION and NOTICE warnings in different colors or in different words There are also warning labels on the vehicle which use the same words CAUTION or NOTICE Vehicle Symbols The vehicle has components and labels that use symbols instead of text Symbols are shown along with the text describing the operation or information relating to a specific component control message gage or indicator Section 1 Seats and Restraint Systems Head Restraints 2 0 22 000ccicce canes scccicaciicnes cneenne 1 2 Where to Put the Restraint cee 1 42 Front Seats sce ccscccecs doeestsdeweeieeeleteatala ndvealaedy 1 4 Lower Anchors and Tethers for Mandal SQate ote o55 E 1 4 Children LATCH cssescssesesssetsneessetees 1 43 Power Seali ois ot aac anu eai 1 5 Securing a Child Restraint in a Rear Seat Power LUM ar sssssssesiisseerieseerirserrrrrserreeeern 1 5 Position 00 Ree oar eee ac 1 49 Heated and Ventilated Seats 0 0 eeee 1 6 Securing a Child Restraint in the Right Front Memory Seat and Mirrors c cccccssesseseeseeseeseees 1 6 CA POSION ocan ienn Ea 1 51 Reclining Seatbacks cceceeeeeeeeeneeeeen eee eenes 1 8 Airbag System cece cece nee eee eee eeeneee ees 1 55 Rear Seats cccccccccceceseeneceseeeseeteeeeenees 1 11 Where Are the Airbags scseeeee 1 58 Split Folding Rear Seat 1 11 When
227. em detected with StabiliTrak a Service Stability System message displays on the Driver Information Center DIC and the TCS StabiliTrak warning light flashes on the instrument panel cluster When this message and warning light displays the system is not operational Driving should be adjusted accordingly See DIC Warnings and Messages on page 3 54 and Warning Lights Gages and Indicators on page 3 29 for more information StabiliTrak comes on automatically whenever the vehicle is started The system should be left on to help assist with directional control of the vehicle If StabiliTrak needs to be turned off press the TC traction control on off button See Traction Control System TCS on page 4 6 If cruise control is being used when the StabiliTrak activates the cruise control will automatically disengage When road conditions allow reengage the cruise control See Cruise Control on page 3 13 for more information Panic Brake Assist Your vehicle has a panic brake assist system that monitors the intention of the driver while braking If the system senses that the driver has applied hard fast pressure to the brake pedal the system will generate additional pressure making it easier for the driver to maintain brake application When this happens the brake pedal will feel easier to push Just hold the brake pedal down firmly and let the system work for you You may feel the brakes vibrate or you may notice some noise b
228. en if the key is not in the ignition switch Horn Press near or on the horn symbols on the steering wheel pad to sound the horn Tilt and Telescopic Steering Wheel A tilt and telescope wheel lets you adjust the steering wheel before you drive The steering wheel can be raised to the highest level to give your legs more room when entering and exiting the vehicle The tilt and telescope lever is located on the left side of the steering column To tilt and telescope the steering wheel pull the lever down Then move the steering wheel up or down or backward or forward into a comfortable position Pull the lever up to lock the steering wheel in place Power Tilt Wheel and Telescopic Steering Column If your vehicle has this feature the power tilt wheel control is located on the left side of the AN steering column To operate the power tilt feature push the control up and the steering wheel tilts up Push the control down and the steering wheel goes down Push the control forward and the steering wheel moves toward the front of the vehicle Push the control rearward and the steering wheel moves toward the rear of the vehicle Turn Signal Multifunction Lever The lever on the left side of the steering column includes the following Turn and Lane Change Signals See Turn and Lane Change Signals on page 3 8 3 Exterior Lamp Control See Headlamps on page 3 16 D Headlamp High Low Beam Changer See
229. ence that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment Universal Home Remote System Operation With One Triangular LED If there is one triangular Light Emitting Diode LED indicator light above the Universal Home Remote buttons follow the instructions below This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers security systems and home automation devices Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature This includes any garage door opener model manufactured before April 1 1982 Read the instructions completely before attempting to program the Universal Home Remote Because of the steps involved it may be helpful to have another person available to assist you in the programming the Universal Home Remote Keep the original hand held transmitter for use in other vehicles as well as for future Universal Home Remote programming It is also recommended that upon the sale of the vehicle t
230. ended fuel See Gasoline Octane on page 5 5 The services in Scheduled Maintenance on page 6 4 should be performed when indicated See Additional Required Services on page 6 5 and Maintenance Footnotes on page 6 6 for further information A CAUTION Performing maintenance work on a vehicle can be dangerous In trying to do some jobs you can be seriously injured Do your own maintenance work only if you have the required know how and the proper tools and equipment for the job If you have any doubt see your dealer retailer to have a qualified technician do the work See Doing Your Own Service Work on page 5 4 Some maintenance services can be complex So unless you are technically qualified and have the necessary equipment you should have your dealer retailer do these jobs When you go to your dealer retailer for your service needs you will know that trained and supported service technicians will perform the work using genuine parts If you want to purchase service information see Service Publications Ordering Information on page 7 15 Owner Checks and Services on page 6 8 tells you what should be checked when to check it and what you can easily do to help keep your vehicle in good condition The proper replacement parts fluids and lubricants to use are listed in Recommended Fluids and Lubricants on page 6 11 and Maintenance Replacement Parts on page 6 13 When your vehicle is serviced make sure these are used All
231. enger sensing system has allowed the airbags to be enabled the on indicator will light and stay lit to remind you that the airbags are active 1 66 For some children who have outgrown child restraints and for very small adults the passenger sensing system may or may not turn off the right front passenger s frontal airbag and seat mounted side impact airbag depending upon the person s seating posture and body build Everyone in your vehicle who has outgrown child restraints should wear a safety belt properly whether or not there is an airbag for that person If a person of adult size is sitting in the right front passenger s seat but the off indicator is lit it could be because that person is not sitting properly in the seat If this happens turn the vehicle off remove any additional material from the seat such as blankets cushions seat covers seat heaters or seat massagers and ask the person to place the seatback in the fully upright position then sit upright in the seat centered on the seat cushion with the person s legs comfortably extended Restart the vehicle and have the person remain in this position for two to three minutes This will allow the system to detect that person and then enable the right front passenger s frontal airbag and seat mounted side impact airbag A CAUTION If the airbag readiness light in the instrument panel cluster ever comes on and stays on it means that something may be wrong
232. engine is running at high speed Notice Shifting out of PARK P or NEUTRAL N with the engine running at high speed may damage the transmission The repairs would not be covered by your warranty Be sure the engine is not running at high speed when shifting your vehicle DRIVE D This position is for normal driving It provides the best fuel economy for your vehicle If you need more power for passing and you are e Going less than 35 mph 55 km h push the accelerator pedal about halfway down e Going about 35 mph 55 km h or more push the accelerator all the way down The transmission will shift down to a lower gear and have more power Downshifting the transmission in slippery road conditions could result in skidding see Skidding under Loss of Control on page 4 13 MANUAL MODE M This position lets drivers select the range of gears appropriate for current driving conditions If your vehicle has this feature see Driver Shift Control DSC later in this section Notice Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission If you are stuck do not spin the tires When stopping on a hill use the brakes to hold the vehicle in place Driver Shift Control DSC Notice f you drive your vehicle at high RPMs without upshifting while using Driver Shift Control DSC you could damage your vehicle Always upshift when necessary while using D
233. ens 5 38 Tilt Wheel and Telescopic Steering Column 3 7 WINGOWS ieseana a a A 2 24 PYIVECY E E E T 7 16 Event Data Recorders ascsccssscsererrerrrerenea 7 17 Navigation System c ceeeeeeeeeeeeeeeeeee eee ees 7 18 ONSA oheen setet sits e EANES 7 18 Radio Frequency Identification 05 7 18 Programmable Automatic Door Locks 2 18 R Radio Frequency Identification RFID Privacy 7 18 Radios a deercacaeccaasecs oean e eneetatac anaes 3 79 FRAGIO S euenien E a oee 3 80 Radios Navigation Radio System see Navigation Manual saisrironsararsiatneenena nena 3 106 Recep seicornre iana oi 3 107 Theft Deterrent ceeeeeneeeeeeeeeeeeeeeeeeees 3 106 Rainsense Wipers cceeeeeneceeeeeeeeeeeees 3 10 Reading Lamps seners monrnon en 3 20 Rear AMI sic iiticestistiiecsscdencavesncnceriisn excertcweeterd 5 50 PIMILEOHSIIP zap e e E E E 4 8 Rear Door Security LOCKS sceceeeceeseeeeeeeen 2 19 Rearview Mirror Automatic Dimming With OnStar esd cseszeccvsuiasageesacezedleeegtevadesgeas 2 49 Reclining Seatbacks cceeeeeeeeneeeeeeeeeeeeeee es 1 8 Recommended Fluids and Lubricants 6 11 Recreational Vehicle Towing eeeeeeeeeeee 4 27 Remote Keyless Access System 0 eeeeeee 2 6 Remote Keyless Entry RKE System 065 2 5 Remote Keyless Entry RKE System OD SAN OM sen a O 2 7 Remote Vehicle Start
234. er or a private collision repair facility to fix the damage make sure you are comfortable with them Remember you will have to feel comfortable with their work for a long time e Once you have an estimate read it carefully and make sure you understand what work will be performed on your vehicle If you have a question ask for an explanation Reputable shops welcome this opportunity Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs GM recommends that you take an active role in its repair If you have a pre determined repair facility of choice take your vehicle there or have it towed there Specify to the facility that any required replacement collision parts be original equipment parts either new Genuine GM parts or recycled original GM parts Remember recycled parts will not be covered by your GM vehicle warranty Insurance pays the bill for the repair but you must live with the repair Depending on your policy limits your insurance company may initially value the repair using aftermarket parts Discuss this with your repair professional and insist on Genuine GM parts Remember if your vehicle is leased you may be obligated to have the vehicle repaired with Genuine GM parts even if your insurance coverage does not pay the full cost If another party s insurance company is paying for the repairs you are not obligated to accept a repair valuation based on that insurance c
235. er air to the side of the vehicle facing the sun The recirculation mode will also be activated as necessary Do not cover the sensors or the automatic climate control system will not work properly Outlet Adjustment Use the air outlets located in the center and on the side of the instrument panel to direct the airflow Use the thumbwheels near the air outlets to open or close off the airflow Operation Tips e Clear away any ice snow or leaves from air inlets at the base of the windshield that could block the flow of air into the vehicle e Keep the path under the front seats clear of objects to help circulate the air inside of the vehicle more effectively e Use of non GM approved hood deflectors can adversely affect the performance of the system Check with your dealer retailer before adding equipment to the outside of your vehicle 3 27 Passenger Compartment Air Filter The passenger compartment air filter traps most of the dust and pollen from the air entering the vehicle The filter will need to be changed periodically See Scheduled Maintenance on page 6 4 Using the climate control system without the passenger air filter installed could let water or other debris enter the system This could cause a water leak or noises Make sure to install a new air filter after removing the old one
236. er gear if the engine RPM is too high If shifting is prevented for any reason the currently selected gear will flash multiple times indicating that the transmission has not shifted gears While in the DSC mode the transmission will automatically downshift when the vehicle comes to a stop and while quickly applying the accelerator to increase speed This will allow for more power during take off When accelerating your vehicle from a stop in snowy and icy conditions you may want to shift into second gear A higher gear ratio allows you to gain more traction on slippery surfaces Manual Transmission Operation If your vehicle has a manual transmission the shift lever is located on the center console between the front seats The following explains how to operate the manual transmission FIRST 1 Press the clutch pedal and shift into FIRST 1 Then slowly let up on the clutch pedal as you press the accelerator pedal Shift into FIRST 1 when you are going less than 25 mph 40 km h If you come to a complete stop and it is hard to shift into FIRST 1 put the shift lever in NEUTRAL and let up on the clutch Press the clutch pedal back down Then shift into FIRST 1 SECOND 2 Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND 2 Then slowly let up on the clutch pedal as you press the accelerator pedal THIRD 3 FOURTH 4 FIFTH 5 and SIXTH 6 Shift into THIRD 3 FOURT
237. er the vehicle Raise the jack by turning the wheel wrench clockwise until the slots in the jack head fit into the metal flange located behind the V shaped locating notches on the plastic molding as shown 7 Put the compact spare tire near you Raise the vehicle by turning the wheel wrench clockwise Raise the vehicle far enough off the ground for the compact spare tire to fit under the vehicle 5 107 9 Remove all the wheel b nuts and the flat tire AN CAUTION Never use oil or grease on studs or nuts Because the nuts might come loose The vehicle s wheel could fall off causing a crash Er V O GA A CAUTION Rust or dirt on a wheel or on the parts to which it is fastened can make wheel nuts become loose after time The wheel could come off and cause an accident When you change a wheel A O Ss 10 Remove any rust or dirt from the wheel bolts mounting surfaces and spare wheel remove any rust or dirt from places where the wheel attaches to the vehicle In an emergency you can use a cloth or a paper towel to do this but be sure to use a scraper or wire brush later if needed to get all the rust or dirt off See Changing a Flat Tire on page 5 102 11 Install the spare tire 12 Put the wheel nuts back on with the rounded end of the nuts toward the wheel 5 108 13 Tighten each wheel nut by turning it clockwise with your hand until the wheel is held against the hub 14
238. es 5 000 km and should not be driven at speeds over 65 mph 105 km h The compact spare tire is for emergency use when a regular road tire has lost air and gone flat If your vehicle has a compact spare tire see Compact Spare Tire on page 5 111 and If a Tire Goes Flat on page 5 83 B Tire Ply Material The type of cord and number of plies in the sidewall and under the tread C Tire Identification Number TIN The letters and numbers following the DOT Department of Transportation code is the Tire Identification Number TIN The TIN shows the manufacturer and plant code tire size and date the tire was manufactured The TIN is molded onto both sides of the tire although only one side may have the date of manufacture D Maximum Cold Inflation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load E Tire Inflation The temporary use tire or compact spare tire should be inflated to 60 psi 420 kPa For more information on tire pressure and inflation see Inflation Tire Pressure on page 5 67 F Tire Size A combination of letters and numbers define a tire s width height aspect ratio construction type and service description The letter T as the first character in the tire size means the tire is for temporary use only G TPC Spec Tire Performance Criteria Specification Original equipment tires designed to GM s specific tire performance criteria have a TPC spe
239. es at 3 000 mile 4 800 km intervals These tires are optimized for dry traction and handling performance Tread life may be 15 000 miles 24 140 km or less for these tires depending on how and where you drive Any time you notice unusual wear rotate your vehicle s tires as soon as possible and check wheel alignment Also check for damaged tires or wheels See When It Is Time for New Tires on page 5 76 and Wheel Replacement on page 5 81 for more information When rotating your vehicle s tires always use the correct rotation pattern shown here If your vehicle has a compact spare tire do not include it in the tire rotation After the tires have been rotated adjust the front and rear inflation pressures as shown on the Tire and Loading Information label See nflation Tire Pressure on page 5 67 and Loading Your Vehicle on page 4 22 Reset the Tire Pressure Monitor System See Tire Pressure Monitor Operation on page 5 71 5 75 Make certain that all wheel nuts are properly When It Is Time for New Tires tightened See Wheel Nut Torque under Capacities and Specifications on page 5 128 Various factors such as maintenance temperatures driving speeds vehicle loading and road conditions A CAUTION influence when you need new tires Rust or dirt on a wheel or on the parts to which it is fastened can make wheel nuts become loose after time The wheel could come off and cause an accident When you One way
240. essure to the seatback and the seatback will return to the upright position Push and pull on the seatback to make sure it is locked Power Reclining Seatbacks If your seats have power reclining seatbacks use the vertical power seat control located on the outboard side of each seat e To recline the seatback press the control toward the rear of the vehicle e To raise the seatback press the control toward the front of the vehicle A CAUTION Sitting in a reclined position when your vehicle is in motion can be dangerous Even if you buckle up your safety belts cannot do their job when you are reclined like this The shoulder belt cannot do its job In a crash you could go into it receiving neck or other injuries The lap belt cannot do its job either In a crash the belt could go up over your abdomen The belt forces would be there not at your pelvic bones This could cause serious internal injuries For proper protection when the vehicle is in motion have the seatback upright Then sit well back in the seat and wear your safety belt properly Do not have a seatback reclined if your vehicle is moving Rear Seats Split Folding Rear Seat Your vehicle may have a split folding rear seat To lower one or both of the rear seatbacks 1 Pull forward on the tab located on the outboard side of the seatback to unlock the seatback Notice Folding a rear seat with the safety belts still fasten
241. ety Defects to General Motors Service Publications Ordering Information Vehicle Data Recording and Privacy Event Data Recorders OnStar Navigation System Radio Frequency Identification RFID Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac Normally any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer s sales or service departments Sometimes however despite the best intentions of all concerned misunderstandings can occur If your concern has not been resolved to your satisfaction the following steps should be taken STEP ONE Discuss your concern with a member of dealership management Normally concerns can be quickly resolved at that level If the matter has already been reviewed with the sales service or parts manager contact the owner of the dealership or the general manager STEP TWO If after contacting a member of dealership management it appears your concern cannot be resolved by the dealership without further help in the United States contact the Cadillac Customer Assistance Center 24 hours a day by calling 1 800 458 8006 In Canada contact the Canadian Cadillac Customer Communication Centre by calling 1 888 446 2000 We encourage you to call the toll free number in order to give your inquiry prompt attention Please have the following information avai
242. evel surface When your engine is cold the coolant level should be at the FROID FULL COLD line on the side of the surge tank Follow the arrow from the top of the tank down the side to the horizontal mark 5 29 Adding Coolant If more coolant is needed add the proper DEX COOL coolant mixture at the surge tank but only when the engine is cool A CAUTION You can be burned if you spill coolant on hot engine parts Coolant contains ethylene glycol and it will burn if the engine parts are hot enough Do not spill coolant on a hot engine When replacing the pressure cap make sure it is hand tight and fully seated 5 30 Coolant Surge Tank Pressure Cap Notice If the pressure cap is not tightly installed coolant loss and possible engine damage may occur Be sure the cap is properly and tightly secured The coolant surge tank pressure cap must be fully installed on the coolant surge tank See Engine Compartment Overview on page 5 14 for more information on location Engine Overheating There are two engine hot messages that may be displayed in the Driver Information Center DIC See DIC Warnings and Messages on page 3 54 for more information If Steam Is Coming From Your Engine A CAUTION Steam from an overheated engine can burn you badly even if you just open the hood Stay away from the engine if you see or hear steam coming from it Turn it off and get everyone away from the vehicle until it cools down
243. ey in the driver s door key cylinder or the transmitter a ten second pre alarm will occur The horn will chirp and the lights will flash If the ignition is turned to START or the door is not unlocked by pressing the unlock button on the transmitter during the ten second pre alarm the alarm will go off Your vehicle s headlamps will flash and the horn will sound for about 30 seconds then will turn off to save the battery power The theft deterrent system will not activate if the doors are locked with the vehicle s key or the manual door lock It activates only if the power door lock switch is used while the door is open or with the transmitter You should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off To avoid setting off the alarm by accident e Lock the vehicle with the door key after the doors are closed e Always unlock a door with the transmitter Unlocking a door any other way will set off the alarm If you set off the alarm by accident turn off the alarm by pressing the unlock button on the transmitter The alarm will not stop if you try to unlock a door any other way 2 27 Testing the Alarm The alarm can be tested by following these steps 1 From inside the vehicle lower the drivers window and open the driver s door 2 Activate the system by locking the doors with the transmitter 3 Get out of the vehicle close the door and wait for the
244. ey from the ignition and press to lock the doors Delayed Locking With this feature you can delay the actual locking of the doors When the power door lock switch is pressed when the key is not in the ignition and the driver s door is opened a chime will sound three times indicating that delayed locking is active When all the doors are closed the doors will lock automatically after five seconds If a door is reopened before five seconds have elapsed the five second timer will reset itself once all the doors are closed again You can press the door lock switch again or the lock button on the RKE transmitter to override this feature and lock the doors immediately You can turn this feature off using the Driver Information Center DIC When delayed locking is off the doors will lock immediately when you press the power 2 18 door lock switch or the lock button on the RKE transmitter See DIC Vehicle Customization on page 3 68 for more information Programmable Automatic Door Locks If your vehicle has an automatic transmission the vehicle is programmed so that the doors will lock automatically when all doors are closed the ignition is on and the shift lever is moved out of PARK P The doors will automatically unlock when you stop the vehicle and move the shift lever back into PARK P If your vehicle has a manual transmission the vehicle is programmed so that the doors will lock automatically after the vehicle sp
245. f the light continues to flash when it is safe to do so stop the vehicle Find a safe place to park the vehicle Turn the ignition off wait at least 10 seconds and restart the engine If the light remains on steady see If the Light Is On Steady following If the light is still flashing follow the previous steps and see your dealer retailer for service as soon as possible If the Light Is On Steady You might be able to correct the emission system malfunction by considering the following Did you recently put fuel into your vehicle If so reinstall the fuel cap making sure to fully install the cap See Filling the Tank on page 5 8 The diagnostic system can determine if the fuel cap has 3 42 been left off or improperly installed A loose or missing fuel cap allows fuel to evaporate into the atmosphere A few driving trips with the cap properly installed should turn the light off Did you just drive through a deep puddle of water If so your vehicle s electrical system might be wet The condition is usually corrected when the electrical system dries out A few driving trips should turn the light off Have you recently changed brands of fuel If so be sure to fuel your vehicle with quality fuel See Gasoline Octane on page 5 5 Poor fuel quality causes the engine not to run as efficiently as designed You might notice this as stalling after start up stalling when you put the vehicle into gear misfiring hesitati
246. f the right front passenger s frontal airbag and seat mounted side impact airbag under certain conditions The driver s airbags are not part of the passenger sensing system 1 64 The passenger sensing system works with sensors that are part of the right front passenger s seat The sensors are designed to detect the presence of a properly seated occupant and determine if the right front passenger s frontal airbag and seat mounted side impact airbag should be enabled may inflate or not Accident statistics show that children are safer if they are restrained in the rear rather than the front seat We recommend that children be secured in a rear seat including an infant or a child riding in a rear facing child restraint a child riding in a forward facing child seat an older child riding in a booster seat and children who are large enough using safety belts A label on your sun visor says Never put a rear facing child seat in the front This is because the risk to the rear facing child is so great if the airbag deploys A CAUTION A child in a rear facing child restraint can be seriously injured or killed if the right front passenger s airbag inflates This is because the back of the rear facing child restraint would be very close to the inflating airbag CAUTION Continued CAUTION Continued Even though the passenger sensing system is designed to turn off the right front passenger s frontal and
247. f the vehicle to open the trunk from the inside Windows Z CAUTION Leaving children helpless adults or pets in a vehicle with the windows closed is dangerous They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke Never leave a child a helpless adult or a pet alone in a vehicle especially with the windows closed in warm or hot weather 2 23 The power window switches are located on the driver s door Power Windows Z CAUTION Leaving children helpless adults or pets in a vehicle with the windows closed is dangerous They can be overcome from extreme heat in warm or hot weather and suffer permanent injuries or even death from heat stroke Leaving children in a vehicle with the ignition key is dangerous for many reasons children or others could be badly injured or even killed They cou d operate tie power windews or positions for both up and down movement and the rear omer controls o even make me venice move power window switch operates with one position for The windows will function with the keys in the up and two positions for down movement Press ignition and they could be seriously injured or the switch to the first position to lower the window to the killed if caught in the path of a closing desired level Pull the switch up to raise the window window Do not leave keys in a vehicle with Your vehicle has Retained Accessory Power RAP that ch
248. fely possible and turn the ignition off Then start the engine again to reset the system If the ABS light still stays on or comes on again while you are driving your vehicle needs service If the regular brake system warning light is not on your vehicle still has brakes but not antilock brakes If the regular brake system warning light is also on your vehicle does not have antilock brakes and there is a problem with the regular brakes See Brake System Warning Light on page 3 37 3 38 For vehicles with a Driver Information Center DIC see DIC Warnings and Messages on page 3 54 for all brake related DIC messages Traction Control System TCS StabiliTrak Warning Light QD ee The Traction Control System StabiliTrak warning light should come on briefly when the engine is started If the warning light does not come on then have it fixed so it will be ready to warn you if there is a problem If it stays on or comes on when you are driving there may be a problem with your Traction Control System TCS StabiliTrak and your vehicle may need service When this warning light is on the system will not limit wheel spin Adjust your driving accordingly If the traction control system warning light comes on and stays on for an extended period of time when the system is turned on your vehicle needs service See Traction Control System TCS on page 4 6 and StabiliTrak System on page 4 8 for more information Engi
249. ff The horn will not chirp when a keyless access transmitter is inside of the vehicle while the ignition is turned off and the driver s door is closed Electronic Key Reminder On default The horn will chirp three times when a keyless access transmitter is inside of the vehicle while the ignition is turned off and the driver s door is closed No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Chime Volume This feature allows you to select the volume level of the chime Press the customization button until Chime Volume appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Normal The chime volume will be set to a normal level Loud The chime volume will be set to a loud level No Change No change will be made to this feature The current setting will remain There is no default for chime volume The volume will stay at the last known setting To select a setting press the set reset button while the desired setting is displayed on the DIC 3 75 Park Tilt Mirrors If your vehicle has this feature it allows you to select whether or not the outside mirror s will automatically tilt down when the vehicle is shifted into REVERSE R See Park Tilt Mirrors on page
250. form Tire Quality Grading Standards A tire information system that provides consumers with ratings for a tire s traction temperature and treadwear Ratings are determined by tire manufacturers using government testing procedures The ratings are molded into the sidewall of the tire See Uniform Tire Quality Grading on page 5 80 Vehicle Capacity Weight The number of designated seating positions multiplied by 150 Ibs 68 kg plus the rated cargo load See Loading Your Vehicle on page 4 22 Vehicle Maximum Load on the Tire Load on an individual tire due to curb weight accessory weight occupant weight and cargo weight Vehicle Placard A label permanently attached to a vehicle showing the vehicle s capacity weight and the original equipment tire size and recommended inflation pressure See Tire and Loading Information Label under Loading Your Vehicle on page 4 22 Inflation Tire Pressure Tires need the correct amount of air pressure to operate effectively Notice Do not let anyone tell you that under inflation or over inflation is all right It is not If your tires do not have enough air under inflation you can get the following Too much flexing e Too much heat Tire overloading Premature or irregular wear Poor handling Reduced fuel economy If your tires have too much air over inflation you can get the following e Unusual wear Poor handling Rough ride e Needless d
251. g it from the display you still must reset the engine oil life system separately For more information on resetting the engine oil life system see Engine Oil Life System on page 5 19 Check Tire Pressure This message displays when the pressure in one or more of the vehicle s tires needs to be checked This message also displays Left Front Right Front Left Rear or Right Rear to indicate which tire needs to be checked You can receive more than one tire pressure message at a time To read the other messages that may have been sent at the same time press the set reset button If a tire pressure message appears on the DIC stop as soon as you can Have the tire pressures checked and set to those shown on the Tire Loading Information label See Tires on page 5 59 Loading Your Vehicle on page 4 22 and Inflation Tire Pressure on page 5 67 The DIC display also shows the tire pressure values See DIC Operation and Displays on page 3 48 lf the tire pressure is low the low tire pressure warning light comes on See Tire Pressure Light on page 3 40 Cruise Set To XXX MPH km h This message displays whenever the cruise control is set See Cruise Control on page 3 13 for more information Driver Door Open This message displays when the driver door is not closed completely Make sure that the door is closed completely Electronic Key Already Known If your vehicle has the keyless access system this message displays if you try to
252. g should you keep the coolant heater plugged in The answer depends on the outside temperature the kind of oil you have and some other things Instead of trying to list everything here we ask that you contact your dealer retailer in the area where you will be parking your vehicle The dealer retailer can give you the best advice for that particular area Automatic Transmission Operation The shift lever is located on the center console between the front seats There are several different positions for the shift lever PARK P This position locks the rear wheels It is the best position to use when you start the engine because your vehicle cannot move easily A CAUTION It is dangerous to get out of your vehicle if the shift lever is not fully in PARK P with the CAUTION Continued CAUTION Continued parking brake firmly set Your vehicle can roll Do not leave your vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle will not move even when you are on fairly level ground always set your parking brake and move the shift lever to PARK P See Shifting Into PARK P Automatic Transmission on page 2 44 If you are pulling a trailer see Towing a Trailer on page 4 29 Make sure the shift lever is fully in PARK P before starting the engine Your vehicle has an automatic trans
253. ge No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Remote Door Unlock This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry RKE or keyless access transmitter or when the vehicle is automatically unlocked using the Keyless Unlock feature You will not receive feedback when unlocking the vehicle with the transmitter if the doors are open See Remote Keyless Entry RKE System Operation on page 2 7 Keyless Access System Operation on page 2 9 or Keyless Unlock later in this section for more information Press the customization button until Remote Door Unlock appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Lights Off The exterior lamps will not flash when you press the unlock button on the transmitter Lights On default The exterior lamps will flash when you press the unlock button on the transmitter No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Delay Door Lock This feature allows you to select whether or not the locking of the vehicle s doors will be del
254. gnment and Tire Balance 5 81 Different SIZE ereidsinn eae 5 79 Replacement eceeeeeeeteeeeeeeeeceeeeeeeeenees 5 81 Where to Put the Restraint eee ees 1 42 WIRQOWS dccuideestei stench at en E E O cites 2 23 OWGE sa races a E E EA 2 24 13 Wi Wi Wi Wi 14 ndshield Rainsense WipeQrs ccceeeeeeeeeeeeeeeeeees 3 10 Washer eenn a lactis E REA 3 11 Washer FIUldi ienes nusse niiin ntse nisani 5 39 Wiper Blade Replacement sasacnscsenereenn 5 57 Wiper Blades Cleaning 0 ceeeeeeeneee ees 5 117 Wiper FUSES acct accncieteernenavie nach etenenceanine 5 121 WIPGIS setir a na a E 3 9 MCSE DIVING cei saddens mienon paean EiS 4 18 ter TICS esecact sieves niederen aeiae 5 60 per Activated Headlamps seeeeeeeeeee ee 3 17 XM Radio Messages sceeeeeeeeteeeneeeee ees 3 105 XM Satellite Radio Antenna System 3 108 Your Vehicle and the Environment 0 6 2
255. h that person s chance of being killed or permanently disabled is higher than if the person had not been drinking Control of a Vehicle The following three systems help to control your vehicle while driving brakes steering and accelerator At times as when driving on snow or ice it is easy to ask more of those control systems than the tires and road can provide Meaning you can lose control of your vehicle See Traction Control System TCS on page 4 6 Adding non dealer non retailer accessories can affect your vehicle s performance See Accessories and Modifications on page 5 3 Braking See Brake System Warning Light on page 3 37 Braking action involves perception time and reaction time First you have to decide to push on the brake pedal That is perception time Then you have to bring up your foot and do it That is reaction time Average reaction time is about three fourths of a second But that is only an average It might be less with one driver and as long as two or three seconds or more with another Age physical condition alertness coordination and eyesight all play a part So do alcohol drugs and frustration But even in three fourths of a second a vehicle moving at 60 mph 100 km h travels 66 feet 20 m That could be a lot of distance in an emergency so keeping enough space between your vehicle and others is important And of course actual stopping distances vary greatly with the surface of
256. han half the tank s capacity to fill the tank Driver Information Center DIC The Driver Information Center DIC gives you the status of many of your vehicle s systems The DIC is also used to display warning status messages All messages appear in the DIC display located at the bottom of the instrument panel cluster The DIC buttons are located on the instrument panel next to the steering wheel The DIC comes on when the ignition is on After a short delay the DIC displays the information that was last displayed before the engine was turned off The top line of the DIC display shows the DIC information The bottom line of the DIC display shows the compass The compass displays in the trip fuel menus and in some vehicle information menus If a problem is detected a warning message appears on the display Take any message that appears on the display seriously and remember that clearing the message only makes the message disappear and does not correct the problem 3 47 DIC Operation and Displays The Driver Information Center DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel next to the steering wheel ZN Trip Fuel Press this button to scroll through the trip and fuel displays See Trip Fuel Display Menu Items following for more information on these displays i Vehicle Information Press this button to scroll through the vehicle information di
257. he desired setting is displayed on the DIC 3 77 Memory Seat Recall If your vehicle has this feature it allows you to select your preference for the remote memory seat recall feature See Memory Seat and Mirrors on page 1 6 for more information Press the customization button until Memory Seat Recall appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off default No remote memory seat recall will occur On The driver s seat and outside mirrors will automatically move to the stored driving position when the unlock button on the Remote Keyless Entry RKE or keyless access transmitter is pressed The steering column will also move on vehicles with the power tilt and telescopic steering feature See Power Tilt Wheel and Telescopic Steering Column on page 3 7 for more information See Relearn Remote Key under DIC Operation and Displays on page 3 48 for more information on matching transmitters to driver ID numbers No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC 3 78 Remote Start If the vehicle has this feature it allows you to turn the remote start feature off or on The remote start feature allows you to start the engine from outside of the vehicle u
258. he vehicle at the wall where it was marked it Step 4 2 Locate the aim dot on the lens of the low beam Notice Do not cover a headlamp to improve beam headlamp cut off when aiming Covering a headlamp may 3 Record the distance from the ground to the aim dot cause excessive heat build up which may cause on the low beam headlamp damage to the headlamp 6 Turn on the low beam headlamps and place a piece of cardboard or equivalent in front of the headlamp not being aimed This should allow only the beam of light from the headlamp being aimed to be seen on the flat surface 5 53 Ly 9 Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal tape Passenger s Side Shown line The lamp on the left A shows the correct headlamp aim The lamp on the right B shows the incorrect headlamp aim 10 Repeat Steps 7 through 9 for the opposite headlamp 7 Locate the vertical headlamp aiming screws which are under the hood near each headlamp assembly The adjustment screw can be turned with a 6 mm hex socket 8 Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line Turn it clockwise or counterclockwise to raise or lower the angle of the beam The top edge of the cut off should be positioned at the bottom edge of the horizontal tape line 5 54 Bulb Replacement Halogen Bulbs For the proper type of replacement bulbs see Replacement Bulbs on
259. he chains too Do not use tire chains on your compact spare Appearance Care Interior Cleaning Your vehicle s interior will continue to look its best if it is cleaned often Although not always visible dust and dirt can accumulate on your upholstery Dirt can damage carpet fabric leather and plastic surfaces Regular vacuuming is recommended to remove particles from your upholstery It is important to keep your upholstery from becoming and remaining heavily soiled Soils should be removed as quickly as possible Your vehicle s interior may experience extremes of heat that could cause stains to set rapidly 5 111 Lighter colored interiors may require more frequent cleaning Use care because newspapers and garments that transfer color to your home furnishings may also transfer color to your vehicle s interior When cleaning your vehicle s interior only use cleaners specifically designed for the surfaces being cleaned Permanent damage may result from using cleaners on surfaces for which they were not intended Use glass cleaner only on glass Remove any accidental over spray from other surfaces immediately To prevent over spray apply cleaner directly to the cleaning cloth Notice If you use abrasive cleaners when cleaning glass surfaces on your vehicle you could scratch the glass and or cause damage to the rear window defogger When cleaning the glass on your vehicle use only a soft cloth and glass cleaner Ma
260. he front wheels are straight ahead Try to adjust your speed so you can drive through the curve Maintain a reasonable steady speed Wait to accelerate until you are out of the curve and then accelerate gently into the straightaway Adding non dealer non retailer accessories can affect your vehicle s performance See Accessories and Modifications on page 5 3 Steering in Emergencies There are times when steering can be more effective than braking For example you come over a hill and find a truck stopped in your lane or a car suddenly pulls out from nowhere or a child darts out from between parked cars and stops right in front of you You can avoid these problems by braking if you can stop in time But sometimes you cannot there is not room That is the time for evasive action steering around the problem Your vehicle can perform very well in emergencies like these First apply the brakes See Braking on page 4 3 It is better to remove as much speed as you can from a possible collision Then steer around the problem to the left or right depending on the space available An emergency like this requires close attention and a quick decision If you are holding the steering wheel at the recommended 9 and 3 o clock positions you can turn it a full 180 degrees very quickly without removing either hand But you have to act fast steer quickly and just as quickly straighten the wheel once you have avoided the objec
261. he instructions in this manual 1 1 Find the lower anchors for the desired seating position 1 2 Put the child restraint on the seat 1 3 Attach and tighten the lower attachments on the child restraint to the lower anchors 2 If the child restraint manufacturer recommends that the top tether be attached attach and tighten the top tether to the top tether anchor if equipped Refer to the child restraint instructions and the following steps 2 1 Find the top tether anchor 2 2 Press the ribbed area of the cover to open the cover and expose the anchor 2 3 If you have an adjustable head restraint raise the head restraint 1 47 2 4 Route attach and tighten the top tether according to your child restraint instructions and the following instructions If the position you are using does not have a head restraint and you are using a single tether route the tether over the seatback If the position you are using has a fixed head restraint and you are using a dual tether route the tether around the head restraint If the position you are using has a fixed head restraint and you are using a single tether route the tether over the head restraint If the position you are using does not have a head restraint and you are using a dual tether route the tether over the seatback 3 Push and pull the child restraint in different directions to be sure it is secure 1 48 Securing a Child Restraint
262. he light on the button will illuminate indicating the feature is in use The rear windows still can be raised or lowered using the driver s window switches when the lockout feature is active To restore power to the rear windows press the button again The light on the button will go out Sun Visors Swing down the primary visor to block out glare It can also be detached from the center mount and moved to the side to block glare from that direction The driver s visor may also have buttons for a built in garage door opener See Universal Home Remote System on page 2 56 for more information Lighted Visor Vanity Mirror Pull the visor down and lift the cover to access the mirror A light comes on when the cover is lifted and goes out when it is closed Theft Deterrent Systems Vehicle theft is big business especially in some cities Although your vehicle has a number of theft deterrent features we know that nothing we put on it can make it impossible to steal Theft Deterrent System If your vehicle has this feature the security light is located on the instrument panel cluster To activate the theft deterrent system 1 Open the door 2 Lock the door with the transmitter The security light should come on and stay on 3 Close all doors The security light should go off after about 30 seconds The alarm is not armed until the security light goes off If a locked door or trunk is opened without using the k
263. he programmed Universal Home Remote buttons should be erased for security purposes See Erasing Universal Home Remote Buttons later in this section When programming a garage door park outside of the garage Park directly in line with and facing the garage door opener motor head or gate motor head Be sure that people and objects are clear of the garage door or gate you are programming It is recommended that a new battery be installed in your hand held transmitter for quicker and more accurate transmission of the radio frequency signal 2 57 Programming the Universal Home Do not hold down the buttons for longer than Remote System 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons If you have questions or need help programming the 2 Hold the end of your hand held transmitter Universal Home Remote System call 1 800 355 3515 about 1 to 3 inches 3 to 8 cm away from or go to www homelink com the Universal Home Remote buttons while keeping Programming a garage door opener involves the indicator light in view The hand held time sensitive actions so read the entire procedure transmitter was supplied by the manufacturer of _ before you begin If you do not follow these actions the your garage door opener receiver motor head unit device will time out and you will have to repeat the 3 At the same time press and hold both the Universal procedure Home Remote button that you would
264. he shoulder belt locks if there is a sudden stop or crash 1 17 Q What is wrong with this A The shoulder belt is too loose It will not give as much protection this way A CAUTION You can be seriously hurt if your shoulder belt is too loose In a crash you would move forward too much which could increase injury The shoulder belt should fit snugly against your body Q What is wrong with this A The lap belt is too loose It will not give nearly as much protection this way A CAUTION You can be seriously hurt if your lap belt is too loose In a crash you could slide under the lap belt and apply force on your abdomen This could cause serious or even fatal injuries The lap belt should be worn low and snug on the hips just touching the thighs Q What is wrong with this A The belt is buckled in the wrong place 1 20 A CAUTION You can be seriously injured if your belt is buckled in the wrong place like this In a crash the belt would go up over your abdomen The belt forces would be there not on the pelvic bones This could cause serious internal injuries Always buckle your belt into the buckle nearest you Q What is wrong with this The belt is over an armrest A CAUTION You can be seriously injured if your belt goes
265. he three Universal Home Remote buttons repeat the programming instructions earlier in this section beginning with Step 2 For help or information on the Universal Home Remote System call the customer assistance phone number under Customer Assistance Offices on page 7 5 Storage Areas Glove Box To open press the button Use the key to lock and unlock Cupholder s Your vehicle has cupholders located in front of the center console Push down on the lid to open Instrument Panel Storage Your vehicle has a storage area located below the climate control systems To access push on the lid Center Console Storage Your vehicle has a center console with an upper and lower storage area To access the upper storage area push the button on the front of the console and lift the cover To access the lower storage area pull up on the center console There is an additional storage area behind the center console To access push the cover in 2 61 Convenience Net Your vehicle may have a convenience net in the rear of the vehicle Put small loads behind the net It can also be positioned into an envelope style to hold smaller items The net is not for heavier loads Store them as far forward as you can Sunroof If your vehicle has a power sunroof it will only operate when the ignition is turned on or in ACC ACCESSORY or when Retained Accessory Power RAP is active See Retained Accessory Power RAP on page 2 34 The
266. heduled Maintenance 6 ceeeeeeeeeeeeeeee ees 6 4 Seats Heated and Ventilated Seats eeeeeeeeees 1 6 Memory MITOS siccccise ceeceeitececeaszecca cnet eas ewsveed 1 6 Power Lumbar 0 cccceeeeceeeeeeeseseeeteeeeees 1 5 Power Seat 0 eceseceeeceeeeeeeeceeeeeeeeeeeeeees 1 5 Reclining Seatbacks ccceseeeeeeeeeeeeeee eens 1 8 Split Folding Rear Seat ceceeeeeeee eee 1 11 Securing a Child Restraint Rear Seat Position cc ceeeeeeeeeeeeeeee eee ees 1 49 Right Front Seat Position 0 ee 1 51 Security Ligi si seseseuhe eleva nnna ER a aes 3 45 STAVE E E E E E 5 3 Accessories and Modifications 5 3 Adding Equipment to the Outside Of Your Vehicle is c 0caneiaecsneteenansenasceneerasane 5 5 California Perchlorate Materials Requirements 5 4 California Proposition 65 Warning 00 5 4 Doing Your Own Work 0e eects 5 4 Engine Soon Light cceeeeeeeeeeeeeeeeen ees 3 40 Publications Ordering Information 0 7 15 Service Scheduling Appointments 0ceee 7 9 Servicing Your Airbag Equipped Vehicle 1 68 Sheet Metal Damage eseeeeeeeneeeeeeeeee es 5 118 Shifting Into Park P cccceeeeeeeeeeeeeeeeeeeeeeeens 2 44 Shifting Out of Park P ceeeeeeeeeeeee eee ee eens 2 45 Signals Turn and Lane Change 06 3 8 Spare Tir
267. heduled Maintenance on page 6 4 and Engine Oil on page 5 16 3 50 Remember you must reset the Oil Life yourself after each oil change It does not reset itself Also be careful not to reset the Oil Life accidentally at any time other than when the oil has just been changed It cannot be reset accurately until the next oil change To reset the engine oil life system See Engine Oil Life System on page 5 19 The display shows 100 when the system is reset Units This display allows you to select between English or Metric units of measurement Once in this display press the set reset button to select between English or Metric units Parking Assist If your vehicle has the Ultrasonic Rear Parking Assist URPA system this display allows the system to be turned on or off Once in this display press the set reset button to select between On or Off If you choose On the system turns on If you choose Off the system turns off The URPA system automatically turns back on after each vehicle start When the URPA system is turned off and the vehicle is shifted out of PARK P the DIC displays the Parking Assist Off message as a reminder that the system has been turned off See DIC Warnings and Messages on page 3 54 and Ultrasonic Rear Parking Assist URPA on page 2 51 for more information Tire Pressure The pressure for each tire can be viewed in the DIC The tire pressure is shown in either pounds per square inch psi or ki
268. his is the legal identifier for your vehicle It appears on a plate in the front corner of the instrument panel on the driver side You can see it if you look through the windshield from outside your vehicle The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration Engine Identification The eighth character in the VIN is the engine code This code helps you identify your vehicle s engine specifications and replacement parts See Capacities and Specifications on page 5 128 for your vehicle s engine code Service Parts Identification Label This label is on the spare tire cover It is very helpful if you ever need to order parts The label has the following information e Vehicle Identification Number VIN e Model designation e Paint information e Production options and special equipment Do not remove this label from the vehicle Electrical System Add On Electrical Equipment Notice Do not add anything electrical to your vehicle unless you check with your dealer retailer first Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty Some add on electrical equipment can keep other components from working as they should Add on equipment can drain your vehicle s battery even if your vehicle is not operating Your vehicle has an airbag system Before attempting to add anything electrical to your vehicl
269. hs 100 000 miles 160 000 km warranty period Items covered are hotel meals and rental car e Alternative Service Canada only There may be times when Roadside Service cannot provide timely assistance Your advisor may authorize you to secure local emergency road service and you will be reimbursed up to 100 upon submission of the original receipt to Cadillac Roadside Service Cadillac and General Motors of Canada Limited reserve the right to limit services or reimbursement to an owner or driver when in their sole discretion the claims become excessive in frequency or type of occurrence Cadillac Technician Roadside Service U S only Cadillac s exceptional Roadside Service is more than an auto club or towing service It provides every Cadillac owner in the United States with the advantage of contacting a Cadillac advisor and where available a Cadillac trained dealer technician who can provide on site service A dealer technician will travel to your location within a 30 mile radius of a participating Cadillac dealership If beyond this radius we will arrange to have your car towed to the nearest Cadillac dealership Each technician travels with a specially equipped service vehicle complete with the necessary Cadillac parts and tools required to handle most roadside repairs Calling for Assistance For prompt and efficient assistance when calling please provide the following to the Roadside Service Representative
270. hts flash when the vehicle is unlocked see Remote Door Unlock earlier in this section Press the customization button until Keyless Unlock appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off None of the doors will automatically unlock Entry Door Only Only the driver s door will automatically unlock when you approach the vehicle with the keyless access transmitter and open the driver s door All Doors default All doors will automatically unlock when you approach the vehicle with the keyless access transmitter and open the driver or front passenger door No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Electronic Key Reminder If your vehicle has the keyless access system this feature allows you to select whether or not the horn chirps when the driver s door is closed and there is a keyless access transmitter inside the interior of the vehicle This will only occur when the vehicle is off Press the customization button until Electronic Key Reminder appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Electronic Key Reminder O
271. i 300 kPa whichever is lower See the example following When you end this high speed driving return the tires to the cold tire inflation pressure shown on the Tire and Loading Information label See Loading Your Vehicle on page 4 22 and Inflation Tire Pressure on page 5 67 Example You will find the maximum load and inflation pressure molded on the tire s sidewall in small letters near the rim flange It will read something like this Maximum load 690 kg 1521 Ibs 300 kPa 44 psi Max Press For this example you would set the inflation pressure for high speed driving at 44 psi 300 kPa 5 69 Tire Pressure Monitor System The Tire Pressure Monitor System TPMS uses radio and sensor technology to check tire pressure levels The TPMS sensors monitor the air pressure in your vehicle s tires and transmit tire pressure readings to a receiver located in the vehicle Each tire including the spare if provided should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label you should determine the proper tire inflation pressure for those tires As an added safety feature your vehicle has been equipped with a tire pressure monitoring system TPMS that illuminates a low tire pressure
272. ice A C System This message displays when the electronic sensors that control the air conditioning and heating systems are no longer working Have the climate control system serviced by your dealer retailer if you notice a drop in heating and air conditioning efficiency Service All Wheel Drive This message displays if a problem occurs with the All Wheel Drive AWD system Your vehicle will run in 2WD This could be caused by e An electronics problem e An AWD system oil overheat e Worn out or overheated clutch plates e Various electrical issues If this message appears stop as soon as possible and turn off the ignition for 30 seconds Restart the vehicle and check for the message on the DIC display If the message is still displayed or appears again when you begin driving the system needs service See your dealer retailer right away Service Battery Charging System This message displays when there is a problem with the generator and battery charging systems Driving with this problem could drain the battery Turn off all unnecessary accessories Stop and turn off the vehicle as soon as it is safe to do so Have the electrical system checked by your dealer retailer Under certain conditions the charging system light may also turn on in the instrument panel cluster See Charging System Light on page 3 36 for more information Service Brake Assist This message displays if there is a problem with the brake system The bra
273. icy terms Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts Some insurance companies will not specify aftermarket collision parts When purchasing insurance we recommend that you assure your vehicle will be repaired with GM original equipment collision parts If such insurance coverage is not available from your current insurance carrier consider switching to another insurance carrier If your vehicle is leased the leasing company may require you to have insurance that assures repairs with Genuine GM Original Equipment Manufacturer OEM parts or Genuine Manufacturer replacement parts Read your lease carefully as you may be charged at the end of your lease for poor quality repairs lf a Crash Occurs Here is what to do if you are involved in a crash Try to relax and then check to make sure you are all right If you are uninjured make sure that no one else in your vehicle or the other vehicle is injured If there has been an injury call emergency services for help Do not leave the scene of a crash until all matters have been taken care of Move your vehicle only if its position puts you in danger or you are instructed to move it by a police officer Give only the necessary and requested information to police and other parties involved in the crash Do not discuss your personal condition mental frame of mind or anything u
274. ifted content is being played from the buffer When the radio is playing time shifted content from the buffer a buffer status bar shows below the station number on the left side of screen Press and hold the REV or FWD buttons to rewind or fast forward through the time shift buffer Hold FWD until the end of the currently recorded buffer to resume live radio playback With live radio playing the radio display will no longer show the buffer bar below the station number On AM FM press the REV or FWD button multiple times to rewind or fast forward Each press will rewind or fast forward 30 seconds of content On XM press the REV or FWD button multiple time to jump to the previous or next song or commercial When the radio station is changed the buffer is cleared and automatically restarted for the current station You cannot rewind to content from a previously tuned station Time shifting of AM FM or XM is not available while recording or while other sources of playback are selected Pausing AM FM or XM if equipped with the Vehicle Turned Off If AM FM or XM is paused when the vehicle is turned off the radio will continue to buffer the current radio station for up to one hour If the vehicle is turned back on within one hour the radio will automatically resume playback from the pause point Using the Auxiliary Input Jack The radio system has an auxiliary input jack It is in the center console bin This is
275. ildren allows you to use the power windows once the ignition has been turned off For more information see Retained Accessory Power RAP on page 2 34 In addition each door has a switch for its own window The front power window switch operates with two When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows 2 24 Express Down Window This feature is on all windows Press the switch to the second position and release the switch to activate the express down feature To stop the window as it is lowering pull up briefly on the switch again Express Up Window This feature is on the front windows Pull the switch up to the second position and release the switch to activate the express up feature To stop the window as it is raising pull up or press down briefly on the switch again Programming the Power Windows If the battery on your vehicle has been recharged disconnected or is not working you will need to reprogram each front power window for the express up feature to work Before reprogramming you will need to replace or recharge your vehicle s battery To program each front window follow these steps 1 With the ignition in ACC ACCESSORY ON RUN or when Retained Accessory Power RAP is active close all doors 2 Press and hold the power window switch until the window is fully open 3 Pull the power window switch up until the window is
276. ill be legal not only where you live but also where you will be driving A good source for this information can be state or provincial police e Consider using a sway control You can ask a hitch dealer retailer about sway controls e Do not tow a trailer at all during the first 1 000 miles 1 600 km your new vehicle is driven Your engine axle or other parts could be damaged 4 30 e Then during the first 500 miles 800 km that you tow a trailer do not drive over 50 mph 80 km h and do not make starts at full throttle This helps your engine and other parts of your vehicle wear in at the heavier loads e Obey speed limit restrictions when towing a trailer Do not drive faster than the maximum posted speed for trailers or no more than 55 mph 90 km h to save wear on your vehicle s parts Three important considerations have to do with weight e The weight of the trailer e The weight of the trailer tongue e The total weight on your vehicle s tires Weight of the Trailer How heavy can a trailer safely be It should never weigh more than 1 000 Ibs 450 kg But even that can be too heavy It depends on how you plan to use your rig For example speed altitude road grades outside temperature and how much your vehicle is used to pull a trailer are all important It can also depend on any special equipment that you have on your vehicle and the amount of tongue weight the vehicle can carry See Weight of the T
277. immediately after starting the engine it is possible that the generator can still recharge the battery The battery should recharge while driving but may take a few hours to do so Consider using an auxiliary charger to boost the battery after returning home or to a final destination Make sure you follow the manufacturer s instructions If this message appears while driving or after starting your vehicle and stays on have it checked immediately to determine the cause of this problem To help the generator recharge the battery quickly you can reduce the load on the electrical system by turning off the accessories The normal battery voltage range is 11 5 to 15 5 volts You can monitor battery voltage on the DIC by pressing the vehicle information button until Battery Voltage is displayed 3 56 Calibrating Drive In Circles This message displays when calibrating the compass Drive the vehicle in circles at less than 5 mph 8 km h to complete the calibration See DIC Compass on page 3 52 for more information Calibration Complete This message displays when the compass calibration is complete See DIC Compass on page 3 52 for more information Change Engine Oil Soon When this message displays it means that service is required for your vehicle See your dealer retailer See Engine Oil on page 5 16 and Scheduled Maintenance on page 6 4 for more information When you reset the Change Engine Oil Soon message by clearin
278. in a Rear Seat Position When securing a child restraint in a rear seating position study the instructions that came with your child restraint to make sure it is compatible with this vehicle If your child restraint has the LATCH system see Lower Anchors and Tethers for Children LATCH on page 1 43 for how to install your child restraint using LATCH If you secure a child restraint using a safety belt and it uses a top tether see Lower Anchors and Tethers for Children LATCH on page 1 43 for top tether anchor locations Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be anchored or if the instructions that come with the child restraint say that the top strap must be anchored In Canada the law requires that forward facing child restraints have a top tether and that the tether be attached If your child restraint does not have the LATCH system you will be using the safety belt to secure the child restraint in this position Be sure to follow the instructions that came with the child restraint Secure the child in the child restraint when and as the instructions say If you need to install more than one child restraint in the rear seat be sure to read Where to Put the Restraint on page 1 42 1 Put the child restraint on the seat 2 Pick up the latch plate and run the lap and shoulder portions of the vehicle s safety belt through or aro
279. in your vehicle for five years or 150 000 miles 240 000 km whichever occurs first if you add only DEX COOL extended life coolant The following explains the cooling system and how to add coolant when it is low If the engine overheats see Engine Overheating on page 5 30 A 50 50 mixture of clean drinkable water and DEX COOL coolant will e Give freezing protection down to 34 F 37 C e Give boiling protection up to 265 F 129 C e Protect against rust and corrosion e Help keep the proper engine temperature e Allow the warning lights and gages to work as they should Notice Using coolant other than DEX COOL may cause premature engine heater core or radiator corrosion In addition the engine coolant may require changing sooner at the first maintenance service after each 30 000 miles 50 000 km or 24 months whichever occurs first Any repairs would not be covered by your warranty Always use DEX COOL silicate free coolant in your vehicle 5 27 What to Use Use a mixture of one half clean drinkable water and one half DEX COOL coolant which will not damage aluminum parts If you use this coolant mixture you do not need to add anything else A CAUTION Adding only plain water to your cooling system can be dangerous Plain water or some other liquid such as alcohol can boil before the proper coolant mixture will Your vehicle s coolant warning system is set for the proper coolant mixtu
280. ined that the condition is caused by the type of fuel used repairs might not be covered by your warranty Additives To provide cleaner air all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming allowing the emission control system to work properly In most cases you should not have to add anything to the fuel However some gasolines contain only the minimum amount of additive required to meet U S Environmental Protection Agency regulations To help keep fuel injectors and intake valves clean or if your vehicle experiences problems due to dirty injectors or valves look for gasoline that is advertised as TOP TIER Detergent Gasoline Also your dealer retailer has additives that will help correct and prevent most deposit related problems Gasolines containing oxygenates such as ethers and ethanol and reformulated gasolines might be available in your area We recommend that you use these gasolines if they comply with the specifications described earlier However E85 85 ethanol and other fuels containing more than 10 ethanol must not be used in vehicles that were not designed for those fuels Notice Your vehicle was not designed for fuel that contains methanol Do not use fuel containing methanol It can corrode metal parts in the fuel system and also damage plastic and rubber parts That damage would not be covered under your warranty Some ga
281. ing DVD audio discs in the Bose 5 1 Cabin surround sound system Insert the DVD audio disc into the CD DVD A player DVD AUDIO displays and playback begins The Group and track number displays during playback This type of radio does not support the playback of DVD video discs If you attempt to play a DVD video disc the radio displays Read Error Please Check Disc and ejects the disc CD AUX CD Auxiliary Press to switch between CD DVD A auxiliary input and USB devices lt lt REV Fast Reverse Press to reverse playback quickly within a track Sound is heard at a reduced volume Press once to change playback to a speed of 2X Each successive press changes playback to a speed of 4X 10X or 21X Press gt iil play pause to resume normal playback The elapsed time of the track displays While recording a disc to HDD the fast reverse does not function D gt FWD Fast Forward Press to advance playback quickly within a track Sound is heard at a reduced volume Press once to change playback to a speed of 2X Each successive press changes playback to a speed of 4X 10X or 21X Press gt Il to resume normal playback The elapsed time of the track displays While recording a disc to HDD the fast forward does not function Stopping DVD Audio Playback Press the pushbutton located under the Il stop label to stop playback of the DVD audio disc DVD PreStop displays Press gt Il to resume playback f
282. ing notches located in the plastic molding 5 105 A CAUTION Getting under a vehicle when it is jacked up is dangerous If the vehicle slips off the jack you could be badly injured or killed Never get under a vehicle when it is supported only by a jack A CAUTION Lifting a vehicle and getting under it to do 4 Insert the hooked end of the extension handle maintenance or repairs is dangerous without through the jack and the flat end through the the appropriate safety equipment and training wheel wrench The jack provided with your vehicle is designed only for changing a flat tire If it is used for anything else you or others could be badly injured or killed if the vehicle slips off the jack Use the jack provided with your vehicle only for changing a flat tire 5 106 Z CAUTION Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall To help avoid personal injury and vehicle damage be sure to fit the jack lift head into the proper location before raising the vehicle Notice If you position the jack under the rocker molding and attempt to raise the vehicle you could break the molding and or cause other damage to your vehicle Always position the jack so that when the jack head is raised it will fit firmly in the notch located inboard from the rocker molding 5 Turn the wheel wrench counterclockwise to lower the jack lift head until the jack fits und
283. ing rocks downhill slope area winding roads long grades passing or no passing zones and take appropriate action If you do not shift down the brakes could get so hot that they would not work well You Winter Driving Here are some tips for winter driving e Have your vehicle in good shape for winter e You might want to put winter emergency supplies in your trunk Include an ice scraper a small brush or broom a supply of windshield washer fluid a rag some winter outer clothing a small shovel a flashlight a red cloth and a couple of reflective warning triangles And if you will be driving under severe conditions include a small bag of sand a piece of old carpet or a couple of burlap bags to help provide traction Be sure you properly secure these items in your vehicle Also see Tires on page 5 59 Driving on Snow or Ice Most of the time those places where the tires meet the road probably have good traction However if there is snow or ice between the tires and the road you can have a very slippery situation You have a lot less traction or grip and need to be very careful 4 18 What is the worst time for this Wet ice Very cold snow or ice can be slick and hard to drive on But wet ice can be even more trouble because it can offer the least traction of all You can get wet ice when it is about freezing 32 F 0 C and freezing rain begins to fall Try to avoid driving on wet ice until salt
284. int 1 35 A CAUTION People should never hold an infant in their arms while riding in a vehicle An infant does not weigh much until a crash During a crash an infant will become so heavy it is not possible to hold it For example in a crash at only 25 mph 40 km h a 12 Ib 5 5 kg infant will suddenly become a 240 Ib 110 kg force on a person s arms An infant should be secured in an appropriate restraint 1 36 A CAUTION Children who are up against or very close to any airbag when it inflates can be seriously injured or killed Airbags plus lap shoulder belts offer protection for adults and older children but not for young children and infants Neither the vehicle s safety belt system nor its airbag system is designed for them Young children and infants need the protection that a child restraint system can provide Q What are the different types of add on child A restraints Add on child restraints which are purchased by the vehicle s owner are available in four basic types Selection of a particular restraint should take into consideration not only the child s weight height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used For most basic types of child restraints there are many different models available When purchasing a child restraint be sure it is designed to be used in a motor vehicle If it is the restrain
285. int surface Although no defect in the paint job causes this we will repair at no charge to the owner the surfaces of new vehicles damaged by this fallout condition within 12 months or 12 000 miles 20 000 km of purchase whichever occurs first Vehicle Care Appearance Materials Description Use ni Interior and exterior Polishing Cloth polishing cloth Tar and Road Oil Removes tar road oil Remover and asphalt Chrome Cleaner Use on chrome or and Polish stainless steel i Removes soil and black I marks from whitewalls and raised white lettering Vinyl Cleaner Cleans vinyl Removes dirt grime Glass Cleaner smoke and fingerprints Removes dirt and grime Chrome Wheel Cleaner irom chrome wheels Removes dust fingerprints and surface contaminants Spray on and wipe off Removes swirl marks fine Swirl Remover Polish scratches and other light surface contamination Finish Enhancer 5 119 Description Usas Removes light scratches Cleans shines and ee Shine protects tires No wiping necessary Medium foaming shampoo Cleans Wash Wax Concentrate and lightly waxes Biodegradable and phosphate free Quickly removes spots and stains from carpets Spot Lifter vinyl and cloth upholstery Odorless spray odor Odor Eliminator eliminator used on fabrics vinyl leather and carpet 5 120 Vehicle Identification Vehicle Identification Number VIN SAMPLE4UX1M072675 T
286. io format or the data file format e Itis very hot When the temperature returns to normal the disc should play e You are driving on a very rough road When the road becomes smoother the disc should play e The disc is dirty scratched wet or upside down e The air is very humid If so wait about an hour and try again e There could have been a problem while burning the disc e The label could be caught in the CD DVD A player If the disc is not playing correctly for any other reason try a known good disc If any error occurs repeatedly or if an error cannot be corrected contact your dealer retailer If the radio displays an error message write it down and provide it to your dealer retailer when reporting the problem 3 91 Hard Disk Drive HDD Radios with a hard disk drive are able to record songs from Audio CDs MP3 WMA discs and USB mass storage devices This type of radio has a 40 GB gigabyte HDD A portion of the HDD is used for the storage of radio system files The remainder of the HDD capacity is available for the storage of media files Recording From Audio CDs REC Record While listening to an audio CD press to start recording songs from the disc The radio has the option to record the current song playing or all songs from the CD Press the pushbutton located under the desired record option A status bar appears on the top of the display when the recording process starts The status bar di
287. ion Center DIC will be displayed if the fuel cap is not properly installed See DIC Warnings and Messages on page 3 54 for more information A CAUTION If a fire starts while you are refueling do not remove the nozzle Shut off the flow of fuel by shutting off the pump or by notifying the station attendant Leave the area immediately Notice f you need a new fuel cap be sure to get the right type Your dealer retailer can get one for you If you get the wrong type it may not fit properly This may cause your malfunction indicator lamp to light and may damage your fuel tank and emissions system See Malfunction Indicator Lamp on page 3 40 Filling a Portable Fuel Container i A CAUTION Bring the fill nozzle in contact with the inside of the fill opening before operating the nozzle Contact should be maintained until the filling is complete Do not smoke while pumping fuel Do not use a cellular phone while pumping fuel Never fill a portable fuel container while it is in your vehicle Static electricity discharge from the container can ignite the fuel vapor You can be badly burned and your vehicle damaged if this occurs To help avoid injury to you and others e Dispense fuel only into approved containers e Do not fill a container while it is inside a vehicle in a vehicle s trunk pickup bed or on any surface other than the ground CAUTION Continued Checking Things Under the H
288. ion If this station was one of the presets choose another station for that preset button No Info No artist song title category or text information is available at this time on this channel The system is working properly NotFound There are no channels available for the selected category The system is working properly Radio ID If tuned to channel 0 this message will alternate with the XM Radio 8 digit radio ID label This label is needed to activate the service Unknown If this message is received when tuned to channel 0 there may be a receiver fault Consult with your dealer retailer Check XM If this message does not clear within a short period of time the receiver may have a fault Consult with your dealer retailer 3 105 Navigation Radio System Your vehicle may have a navigation radio system The navigation system has built in features intended to minimize driver distraction Technology alone no matter how advanced can never replace your own judgment See the Navigation System manual for some tips to help you reduce distractions while driving Theft Deterrent Feature THEFTLOCK is designed to discourage theft of your vehicle s radio The feature works automatically by learning a portion of the Vehicle Identification Number VIN If the radio is moved to a different vehicle it does not operate and LOC LOCK or LOCKED could display With THEFTLOCK activated the radio does not operate if stole
289. irbag is in the instrument panel on the passenger s side The driver s frontal airbag is in the middle of the steering wheel 1 58 Driver Side shown Passenger Side similar The seat mounted side impact airbags for the driver and The roof rail airbags for the driver right front passenger right front passenger are in the side of the seatbacks and second row outboard passengers are in the closest to the door ceiling above the side windows 1 59 A CAUTION If something is between an occupant and an airbag the airbag might not inflate properly or it might force the object into that person causing severe injury or even death The path of an inflating airbag must be kept clear Do not put anything between an occupant and an airbag and do not attach or put anything on the steering wheel hub or on or near any other airbag covering Do not use seat accessories that block the inflation path of a seat mounted side impact airbag If your vehicle has roof rail airbags never secure anything to the roof of your vehicle by routing the rope or tie down through any door or window opening If you do the path of an inflating roof rail airbag will be blocked 1 60 When Should an Airbag Inflate Frontal airbags are designed to inflate in moderate to severe frontal or near frontal crashes to help reduce the potential for severe injuries mainly to the driver s or right front passenger s head and chest However they are onl
290. irbag readiness light on the instrument panel cluster which shows the airbag symbol The system checks the airbag s electrical system for malfunctions The light tells you if there is an electrical problem The system check includes the airbag sensor the pretensioners the airbag modules the wiring and the crash sensing and diagnostic module For more information on the airbag system see Airbag System on page 1 55 This light will come on when you start your vehicle and it will flash for a few seconds The light should go out and the system is ready e N If the airbag readiness light stays on after you start the vehicle or comes on when you are driving your airbag system may not work properly Have your vehicle serviced right away A CAUTION If the airbag readiness light stays on after you start your vehicle it means the airbag system may not be working properly The airbags in your vehicle may not inflate in a crash or they could even inflate without a crash To help avoid injury to yourself or others have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle The airbag readiness light should flash for a few seconds when you start the engine If the light does not come on then have it fixed immediately If there is a problem with the airbag system an airbag Driver Information Center DIC message may also come on See DIC Warnings and Messages on page 3 54
291. is left in the ignition while your vehicle is parked The vehicle might not start after it has been parked for an extended period of time Ignition Positions Keyless Access You can turn the ignition control knob to four different positions To shift out of PARK P ignition must be in the ON RUN or ACC ACCESSORY and the regular brake pedal must be applied Using a tool to force the knob from its cylinder could cause damage or break the knob Make sure the keyless access transmitter is inside the vehicle when trying to turn the ignition control knob A LOCK OFF The ignition control knob cannot be removed from the vehicle The keyless access transmitter must be inside the vehicle to start the engine This position locks the ignition and shifter on automatic transmission vehicles and the ignition and steering wheel on manual transmission vehicles B ACC ACCESSORY This position allows you to use things like the radio and the windshield wipers when the engine is off This position will allow you to turn off the engine C ON RUN This position is for driving It is the position the ignition switch returns to after the engine starts and the control knob is released If you need to shift the transmission out of PARK P the ignition control knob has to be in ACC ACCESSORY or ON RUN The battery could be drained if you leave the key in the ACC ACCESSORY or ON RUN position with the engine off You may not be able to
292. is turned off before leaving the vehicle Speed Limited To XXX MPH km h This message displays when your vehicle speed is limited to 80 mph 128 km h because the vehicle detects a problem in the speed variable assist steering magnetic ride control or automatic leveling control systems Have your vehicle serviced by your dealer retailer Sport Mode This message displays when the vehicle is in sport mode See Driver Shift Control DSC under Automatic Transmission Operation on page 2 37 for more information 3 65 StabiliTrak Competitive Mode This message displays when the Competitive Driving mode is selected When in this mode the Traction Control System TCS will not be operating and the TCS warning light will turn on Adjust your driving accordingly See Competitive Driving Mode under Traction Control System TCS on page 4 6 for more information StabiliTrak Not Ready This message may display after first driving the vehicle and exceeding 19 mph 30 km h for 30 seconds The StabiliTrak system is not functional until the message has turned off See StabiliTrak System on page 4 8 for more information StabiliTrak Off This message displays when you turn off StabiliTrak or when the stability control has been automatically disabled To limit wheel spin and realize the full benefits of the stability enhancement system you should normally leave StabiliTrak on However you should turn Stabili
293. ith the engine running But if you ever have to here are some things to know A CAUTION Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle See the earlier caution under Engine Exhaust on page 2 47 Also idling in a closed in place can let deadly carbon monoxide CO into your vehicle even if the climate control fan is at the highest setting One place this can happen is a garage Exhaust with CO can come in easily NEVER park in a garage with the engine running Another closed in place can be a blizzard See Winter Driving on page 4 18 2 48 A CAUTION It can be dangerous to get out of your vehicle if the automatic transmission shift lever is not fully in PARK P with the parking brake firmly set Your vehicle can roll Do not leave your vehicle when the engine is running unless you have to If you have left the engine running the vehicle can move suddenly You or others could be injured To be sure your vehicle will not move even when it is on fairly level ground always set the parking brake and move the automatic transmission shift lever to PARK P or the manual transmission shift lever to NEUTRAL Follow the proper steps to be sure your vehicle will not move See Shifting Into PARK P Automatic Transmission on page 2 44 and Parking Your Vehicle Manual Transmission on page 2 46 If you are parking on a hill and if you are pulling a trailer
294. itter 2 Remove the old battery Do not use a metal object 3 Insert the new battery positive side facing down Replace with a CR2032 or equivalent battery 4 Put the transmitter back together tightly 2 14 Remote Vehicle Start If your vehicle has this feature it allows you to start the engine from outside of the vehicle It may also start the vehicle s automatic climate control system When the remote start system is active the climate control system will heat and cool the inside of the vehicle according to the previous settings of the system before turning the vehicle off The windshield defroster or rear window defogger will be turned on by the climate control system when it is cold outside If the vehicle has heated seats they will also turn on See Heated and Ventilated Seats on page 1 6 for additional information Normal operation of the climate control system will return after the ignition is turned to ON RUN See Dual Climate Control System on page 3 23 Laws in some communities may restrict the use of remote starters For example some laws may require a person using remote start to have the vehicle in view when doing so Check local regulations for any requirements on remote starting of vehicles Do not use the remote start feature if your vehicle is low on fuel Your vehicle may run out of fuel Your transmitter with the remote start button provides an increased range of operation However the range m
295. ke system warning light and the antilock brake system ABS warning light may also display on the instrument panel cluster See Brake System Warning Light on page 3 37 and Antilock Brake System Warning Light on page 3 38 for more information If this happens stop as soon as possible and turn off the vehicle Restart the vehicle and check for the message on the DIC display If the message displays or appears again when you begin driving the brake system needs service See your dealer retailer as soon as possible See Brakes on page 5 40 for more information 3 63 Service Brake System This message displays while the ignition is on when the brake fluid level is low The brake system warning light on the instrument panel cluster also comes on See Brake System Warning Light on page 3 37 for more information Have the brake system serviced by your dealer retailer as soon as possible Service Keyless Start System If your vehicle has the keyless access system this message displays when there is a problem with this feature See your dealer retailer Service Parking Assist If your vehicle has the Ultrasonic Rear Parking Assist URPA system this message displays if there is a problem with the URPA system Do not use this system to help you park See Ultrasonic Rear Parking Assist URPA on page 2 51 for more information See your dealer retailer for service Service Power Steering Your vehicle may have a speed variable assist
296. l be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Easy Exit Setup If your vehicle has this feature it allows you to select which areas will recall with the automatic easy exit seat feature It also allows you to turn off the automatic easy exit feature See Memory Seat and Mirrors on page 1 6 and Easy Exit Recall earlier for more information Press the customization button until Easy Exit Setup appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off No automatic seat exit will recall Seat Only The driver s seat will recall Tilt Only The steering wheel tilt feature will recall Telescope Only The steering column telescope feature will recall Seat Tilt The driver s seat and the steering wheel tilt feature will recall Seat Telescope The driver s seat and the steering column telescope feature will recall Tilt Telescope The steering wheel tilt and steering column telescope features will recall All default The drivers seat and the steering wheel tilt and steering column telescope features will recall if your vehicle has this option No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while t
297. l force outside air into your vehicle See Climate Control System If you have air outlets on or under the instrument panel open them all the way See Engine Exhaust on page 2 47 Trunk Lock Release The remote trunk release button is located on the lower portion of the driver s door To use the remote trunk release the shift lever must be in PARK P or NEUTRAL N for a vehicle with an automatic transmission The shift lever must be in NEUTRAL with the parking brake set for a vehicle with a manual transmission Press the button to open the trunk You can also press the button with the trunk symbol on the Remote Keyless Entry RKE transmitter to open the trunk On vehicles with a Keyless Access System squeeze the trunk release button located on the rear of the trunk lid above the license plate as long as you have your transmitter with you Entry occurs when the button is being pressed and the vehicle recognizes the transmitter The vehicle must be in PARK P and the valet mode turned off If your vehicle is ever without power the trunk area can still be manually accessed by using one of the following procedures On vehicles with a rear seat pass through door 1 Fold the rear armrest down and open the pass through door See Rear Seat Pass Through following for more information 2 Reach upward through the opening to locate the emergency trunk release handle See Emergency Trunk Release Handle
298. l regularly and keep it at the proper level If the system is ever reset accidentally you must change the oil at 3 000 miles 5 000 km since your last oil change Remember to reset the oil life system whenever the oil is changed How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use Whenever the oil is changed reset the system so it can calculate when the next oil change is required If a situation occurs where you change the oil prior to a Change Engine Oil Soon message being turned on reset the system Always reset the engine oil life to 100 after every oil change It will not reset itself To reset the Engine Oil Life System 1 Display the OIL LIFE REMAINING on the DIC 2 Press and hold the SET RESET button on the DIC for more than five seconds The oil life will change to 100 If the Change Engine Oil Soon message comes back on when you start your vehicle the Engine Oil Life System has not reset Repeat the procedure 5 20 What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer Do not let used oil stay on your skin for very long Clean your skin and nails with soap and water or a good hand cleaner Wash or properly dispose of clothing or rags containing used engine oil See the manufacturer s warnings about the use and disposal of oil products
299. lable to give the Customer Assistance Representative e Vehicle Identification Number VIN This is available from the vehicle registration or title or the plate at the top left of the instrument panel and visible through the windshield e Dealership name and location e Vehicle delivery date and present mileage When contacting Cadillac please remember that your concern will likely be resolved at a dealer s facility That is why we suggest you follow Step One first if you have a concern STEP THREE United States Owners Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle However if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two you should file with the Better Business Bureau BBB Auto Line Program to enforce your rights The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty Although you may be required to resort to this informal dispute resolution program prior to filing a court action use of the program is free of charge and your case will generally be heard within 40 days If you do not agree with the decision given in your case you may reject it and proceed with any other venue for relief available to you You may contact the BBB Auto Li
300. lamps are turned off See Fog Lamps on page 3 18 for more information 3 45 Lights On Reminder a 00 See Headlamps on Reminder on page 3 17 for more information Cruise Control Light This light comes on whenever the parking lamps are on This light comes on y whenever you set the cruise control The light goes out when the cruise control is turned off See Cruise Control on page 3 13 for more information 3 46 Highbeam On Light This light comes on when the high beam headlamps are in use See Headlamp High Low Beam Changer on page 3 8 for more information Fuel Gage The fuel gage shows approximately how much fuel is in the fuel tank It works only when the ignition is in the ON RUN position If the fuel supply gets low the Fuel Level Low message will appear on the Driver Information Center DIC and a single chime will sound See DIC Warnings and Messages on page 3 54 for more information Here are a few concerns some owners have had about the fuel gage All of these situations are normal and do not indicate that anything is wrong with the fuel gage e At the gas station the gas pump shuts off before the gage reads full e The gage may change when you turn stop quickly or accelerate quickly e It takes a little more or less fuel to fill the tank than the gage indicated For example the gage may have indicated that the tank was half full but it actually took a little more or less t
301. lby and the double D symbol are trademarks of Dolby Laboratories Radio Data System RDS The audio system has a Radio Data System RDS feature RDS is available for use only on FM stations that broadcast RDS information This system relies upon receiving specific information from these stations and only works when the information is available While the radio is tuned to an FM RDS station the station name or call letters display In rare cases a radio station can broadcast incorrect information that causes the radio features to work improperly If this happens contact the radio station 3 81 Playing the Radio VOL Cy Volume Power The power knob is part of the VOL volume knob and is located above the radio at the left side of the clock Press to turn the system on and off Turn the VOL knob clockwise or counterclockwise to increase or decrease the volume Speed Compensated Volume SCV A Radio with Speed Compensated Volume SCV automatically adjusts the sound to compensate for road and wind noise as the vehicle speeds up or slows down so that the volume is consistent while driving That way the volume level should sound about the same as you drive To activate SCV 1 Set the radio volume to the desired level 2 Press the CONFIG button to display the radio setup menu 3 Press the pushbutton under the AUTO VOL automatic volume label on the radio display 4 Press the pushbutton under the desired Spee
302. le after starting the vehicle driving a short distance is required to calibrate the AFL To enable AFL set the exterior lamp switch on the multifunction lever to the AUTO position Moving the switch out of the AUTO position will deactivate the system See Headlamps on page 3 16 Fog Lamps Use the fog lamps for better vision in foggy or misty conditions The fog lamp control is located on the turn signal multifunction lever 0 Fog Lamps Turn the fog lamp band on the lever up to 40 and release it to turn the fog lamps on or off The band will return to its original position The parking lamps must be on for the fog lamps to work If the high beam headlamps are turned on the fog lamps will also turn off They will turn back on again when you switch back to low beam headlamps Some localities have laws that require the headlamps to be on along with the fog lamps Exterior Lighting Battery Saver The exterior lamps turn off about 10 minutes after the ignition is turned to LOCK OFF if the parking lamps or headlamps have been left on This protects against draining the battery The battery saver does not work if the headlamps are turned on after the ignition is turned to LOCK OFF To keep the lamps on for more than 10 minutes turn the lamps back on with the exterior lamp control Instrument Panel Brightness The knob with this symbol on it is located on the instrument panel to the left of the steering column T
303. le could move suddenly if the shift lever is not fully in PARK P with the parking brake firmly set And if you leave the vehicle with the engine running it could overheat and even catch fire You or others could be injured Do not leave your vehicle with the engine running If you have to leave your automatic transmission vehicle with the engine running be sure your vehicle is in PARK P and your parking brake is firmly set before you leave it After you have moved the shift lever into PARK P hold the regular brake pedal down Then see if you can move the shift lever away from PARK P without first pushing the button If you can it means that the shift lever was not fully locked into PARK P Torque Lock Automatic Transmission If you are parking on a hill and you do not shift the automatic transmission into PARK P properly the weight of the vehicle may put too much force on the parking pawl in the transmission You may find it difficult to pull the shift lever out of PARK P This is called torque lock To prevent torque lock set the parking brake and then shift into PARK P properly before you leave the drivers seat To find out how see Shifting Into Park P previously in the section When you are ready to drive move the shift lever out of PARK P before releasing the parking brake If torque lock does occur you may need to have another vehicle push yours a little uphill to take some of the pres
304. le display shows there is content on the hard drive from five individual artists Select the HDD Menu category to display the available items in each individual category then select an item from one of these submenus to display a list of songs related to that menu item Select a song to begin playback of that song and to put the HDD in the playback mode Recently Saved Select this option from the HDD Menu to display the last 50 songs added since the vehicle was last turned on The songs are categorized into songs recorded from CDs or USB devices Audiblebook The radio is able to play back audio book content downloaded from www audible com This content can be transferred into the HDD by either burning it to a CD or copying it to a USB storage device and then recording it to the HDD The audible com playback requires activation of the vehicle as a player for downloaded content The radio system activates the audible com system when information is found on either a CD inserted into the CD DVD A player or if a USB storage device is connected The Vehicle Identification Number VIN number is a required in order to activate your vehicle 3 97 Saving HDD Favorites During HDD playback press the FAV button to change between favorite modes The following favorite modes are supported e Playlists e Artists e Albums e Genres Favorites can be saved by pressing and holding the pushbutton located under the favorites se
305. lection Store your favorites according to the following table Favorites Display Mode Action on Press and Hold Adds currently playing track to Playlist the playlist selected Saves the artist associated with Artist the currently playing track in the indicated favorites position Saves the album associated with Album the currently playing track in the indicated favorites position Saves the genre associated with Genre the currently playing track in the indicated favorites position 3 98 Configuring HDD Favorites Press the CONFIG button to display the radio configuration options Press the pushbutton under the HDD label to display the available favorite modes Press the pushbutton under the favorite label to set the available favorite modes Available favorite modes are highlighted Time shifting Pause and Rewind Live FM AM and XM if equipped The Radio with DVD Audio HDD and USB has the ability to rewind 60 minutes of FM AM and XM if equipped content While listening to the radio the content from the current station is always being buffered to the HDD Press gt Ul play pause To pause the radio The radio display will show the Time Shift buffer status bar The status bar shows the amount of content that is stored in the buffer and the current pause point To resume playback from the current pause point press gt il again The radio will no longer be playing live radio Instead time sh
306. lic Transportation or Fuel Reimbursement If your vehicle requires warranty repairs and public transportation is used instead of the dealer s shuttle service the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service In addition for U S customers should you arrange transportation through a friend or relative limited reimbursement for reasonable fuel expenses may be available Claim amounts should reflect actual costs and be supported by original receipts See your dealer for information regarding the allowance amounts for reimbursement of fuel or other transportation costs 7 10 Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for a warranty repair If you obtain a rental vehicle on your own please see your dealer for the maximum number of days allowed and the allowance per rental day Rental reimbursement must be supported by original receipts This requires that you sign and complete a rental agreement and meet state local and rental vehicle provider requirements Requirements vary and may include minimum age requirements insurance coverage credit card etc You are responsible for fuel usage charges and may also be responsible for taxes levies usage fees excessive mileage or rental usage beyond the completion of the repair It
307. load Speed ratings range from A to Z 5 64 Tire Terminology and Definitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire Air pressure is expressed in pounds per square inch psi or kilopascal kPa Accessory Weight This means the combined weight of optional accessories Some examples of optional accessories are automatic transmission power steering power brakes power windows power seats and air conditioning Aspect Ratio The relationship of a tire s height to its width Belt A rubber coated layer of cords that is located between the plies and the tread Cords may be made from steel or other reinforcing materials Bead The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim Bias Ply Tire A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread Cold Tire Pressure The amount of air pressure in a tire measured in pounds per square inch psi or kilopascals kPa before a tire has built up heat from driving See Inflation Tire Pressure on page 5 67 Curb Weight The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel oil and coolant but without passengers and cargo DOT Markings A code molded into the sidewall of a tire signifying that the tire is in compliance with the U S Department of Transportation D
308. lopascals kPa Press the vehicle information button until the DIC displays Front Tire PSI kPa Left Right Press the vehicle information button again until the DIC displays Rear Tire PSI kPa Left Right If a low or high tire pressure condition is detected by the system while driving a message advising you to check the pressure in a specific tire appears in the display See Inflation Tire Pressure on page 5 67 and DIC Warnings and Messages on page 3 54 for more information Battery Voltage This display shows the current battery voltage Your vehicle s charging system regulates voltage based on the state of the battery The battery voltage may fluctuate when viewing this information on the DIC This is normal If there is a problem with the battery charging system the charging system light illuminates and or the DIC displays a message See Charging System Light on page 3 36 DIC Warnings and Messages on page 3 54 and Electric Power Management on page 3 20 for more information Calibrate Compass Your vehicle may have this feature The compass can be manually calibrated To calibrate the compass through the DIC see DIC Compass on page 3 52 Change Compass Zone Your vehicle may have this feature To change the compass zone through the DIC see DIC Compass on page 3 52 Relearn Remote Key If your vehicle has the Remote Keyless Entry RKE system this display allows you to match the transmitter to you
309. made Audio System s Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features A CAUTION This system provides you with far greater access to audio stations and song listings Giving extended attention to entertainment tasks while driving can cause a crash and you or others can be injured or killed Always keep your eyes on the road and your mind on the drive avoid engaging in extended searching while driving Keeping your mind on the drive is important for safe driving See Defensive Driving on page 4 2 Here are some ways in which you can help avoid distraction while driving 3 79 While your vehicle is parked e Familiarize yourself with all of its controls e Familiarize yourself with its operation e Set up your audio system by presetting your favorite radio stations setting the tone and adjusting the speakers Then when driving conditions permit you can tune to your favorite radio stations using the presets and steering wheel controls if the vehicle has them Notice Before adding any sound equipment to your vehicle such as an audio system CD player CB radio mobile telephone or two way radio make sure that it can be added by checking with your dealer retailer Also check federal rules covering mobile radio and telephone units If sound equipment can be added it is very important to do it properly Added sound equipment may interfere with
310. matic transmission in PARK P or a manual transmission in NEUTRAL before setting the parking brake Notice lf you leave your radio or other accessories on during the jump starting procedure they could be damaged The repairs would not be covered by your warranty Always turn off your radio and other accessories when jump starting your vehicle 3 Turn off the ignition on both vehicles Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlets Turn off the radio and all lamps that are not needed This will avoid sparks and help save both batteries And it could save the radio 4 Open the hoods and locate the positive and negative terminal locations or the remote positive and remote negative terminals of the other vehicle Then locate the remote positive location on your vehicle See Engine Compartment Overview on page 5 14 for more information on locations the terminals 5 45 Notice If you connect a negative cable to the Engine Control Module ECM ECM mounting bracket or any cables that attach to the ECM bracket you may damage the ECM Always attach the negative cable to your vehicle s remote negative ground location instead of the ECM ECM bracket or any cables attached to the ECM bracket A CAUTION An electric fan can start up even when the engine is not running and can injure you Keep hands clothing and tools away from any underhood electri
311. may cause loss of XM signal for a period of time The radio may display No XM Signal to indicate interference 3 107 Cellular Phone Usage Cellular phone usage may cause interference with your vehicle s radio This interference may occur when making or receiving phone calls charging the phone s battery or simply having the phone on This interference causes an increased level of static while listening to the radio If static is received while listening to the radio unplug the cellular phone and turn it off Backglass Antenna The AM FM antenna is integrated with the rear window defogger located in the rear window Make sure that the inside surface of the rear window is not scratched and that the grid lines on the glass are not damaged If the inside surface is damaged it could interfere with radio reception Notice Using a razor blade or sharp object to clear the inside rear window may damage the rear window antenna and or the rear window defogger Repairs would not be covered by your warranty Do not clear the inside rear window with sharp objects 3 108 Notice Do not apply aftermarket glass tinting with metallic film The metallic film in some tinting materials will interfere with or distort the incoming radio reception Any damage caused to your backglass antenna due to metallic tinting materials will not be covered by your warranty Because this antenna is built into the rear window there is a reduced risk of
312. ment Proper vehicle maintenance not only helps to keep your vehicle in good working condition but also helps the environment All recommended maintenance is important Improper vehicle maintenance can even affect the quality of the air we breathe Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle To help protect our environment and to keep your vehicle in good condition be sure to maintain your vehicle properly Using the Maintenance Schedule We want to help you keep your vehicle in good working condition But we do not know exactly how you will drive it You might drive very short distances only a few times a week Or you might drive long distances all the time in very hot dusty weather You might use your vehicle in making deliveries Or you might drive it to work to do errands or in many other ways Because of all the different ways people use their vehicles maintenance needs vary You might need more frequent checks and replacements So please read the following and note how you drive If you have any questions on how to keep your vehicle in good condition see your dealer retailer This schedule is for vehicles that e carry passengers and cargo within recommended limits You will find these limits on the Tire and Loading Information label See Loading Your Vehicle on page 4 22 e are driven on reasonable road surfaces within legal driving limits e use the recomm
313. mission shift lock control system You must fully apply your regular brakes first and then press the shift lever button before you can shift from PARK P when the ignition key is in ON If you cannot shift out of PARK P ease pressure on the shift lever and push the shift lever all the way into PARK P as you maintain brake application Then press the shift lever button and move the shift lever into another gear See Shifting Out of PARK P on page 2 45 2 37 Notice Shifting to REVERSE R while your vehicle is moving forward could damage the transmission The repairs would not be covered by your warranty Shift to REVERSE R only after your vehicle is stopped REVERSE R Use this gear to back up At low vehicle speeds you can also use REVERSE R to rock your vehicle back and forth to get out of snow ice or sand without damaging your transmission See f Your Vehicle is Stuck in Sand Mud Ice or Snow on page 4 21 for additional information NEUTRAL N In this position the engine does not connect with the wheels To restart when you are already moving use NEUTRAL N only You can also use NEUTRAL N when your vehicle is being towed 2 38 A CAUTION Shifting into a drive gear while the engine is running at high speed is dangerous Unless your foot is firmly on the brake pedal your vehicle could move very rapidly You could lose control and hit people or objects Do not shift into a drive gear while your
314. mmed to complete programming Up to four transmitters can be programmed to the vehicle The DIC will display Maximum Electronic Keys Learned and will exit the programming mode After performing this process transmitters previously programmed will no longer work with your vehicle and must be reprogrammed Battery Replacement Replace the battery if the Replace Battery In Remote Key message displays in the DIC See REPLACE BATTERY IN REMOTE KEY under DIC Warnings and Messages on page 3 54 for additional information A weak battery may also cause the DIC to display Electronic Key Not Detected when you try to start the vehicle If this happens place the transmitter in the center console storage area transmitter pocket with the buttons facing to the front of the vehicle Then with the vehicle in PARK P or NEUTRAL N press the brake pedal and the ignition control knob See Starting the Engine on page 2 34 for additional information about your vehicle s electronic keyless ignition with push start Although this will start the vehicle it is recommended that you replace the transmitter battery as soon as possible Notice When replacing the battery use care not to touch any of the circuitry Static from your body transferred to these surfaces may damage the transmitter To replace the battery 1 Separate the halves of the transmitter with a flat thin object inserted into the slot on the side or back of the transm
315. mp to turn it on or off If the reading lamps are left on they automatically shut off 10 minutes after the ignition has been turned off Electric Power Management The vehicle has Electric Power Management EPM that estimates the battery s temperature and state of charge It then adjusts the voltage for best performance and extended life of the battery When the battery s state of charge is low the voltage is raised slightly to quickly put the charge back in When the state of charge is high the voltage is lowered slightly to prevent overcharging If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center DIC you may see the voltage move up or down This is normal If there is a problem an alert will be displayed 3 20 The battery can be discharged at idle if the electrical loads are very high This is true for all vehicles This is because the generator alternator may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads A high electrical load occurs when several of the following loads are on headlamps high beams fog lamps rear window defogger climate control fan at high speed heated seats engine cooling fans trailer loads and loads plugged into accessory power outlets EPM works to prevent excessive discharge of the battery It does this by balancing the generator s output and the vehicle s electrical needs It can in
316. mps 2 eeeeeeeeeeeeeeeees 5 56 Replacement Bulbs csceeeeeeeeeeeeeeeees 5 57 Buying New TireS cccceeeeeeeeeeneceeeeeeeeeeeees 5 77 Calibratioit accea a E S 3 52 California Fuel 2vccecc scecdeicsssencceinetvessagevesensseveeees 5 6 California Perchlorate Materials Requirements 5 4 California Proposition 65 Warning eeeeeeeeeeeeee 5 4 Canadian Owners ccceceeceeeeceeeeeeeeeceeeeeeeaees iii Capacities and Specifications 00 5 128 Carbon Monoxide 5 2 20 2 47 4 18 4 29 Care of Safety Belts seer acncs nite wecdawednehaecestdadedetans 5 114 GD MPS prasnice eaaa Sluewisiesteesadss 3 101 Center Console Storage Area secese 2 61 Chains TIe coaren eee eE TARA 5 83 Charging System Light eeeeeeeeeeeeeeeeenes 3 36 Check Engine Light ss aeaniee aaan te 3 40 Checking Things Under the Hood 266 5 12 Chemical Paint Spotting neiisrisirsirissiairsesasisrs 5 119 Child Restraints Child Restraint Systems ceeeeeeeeeee eee 1 39 Infants and Young Children s 1 35 Lower Anchors and Tethers for Children 1 43 Older Children 0 ccceceeceeeeceeeeeeeeeeees 1 32 Securing a Child Restraint in a Rear Seat Position cccceeeeceeceeeeeeeeeeeeeeees 1 49 Securing a Child Restraint in the Right Front Seat Position 1 51 Where to Put the Restraint c e
317. mpt to shift with the rear wheels spinning with a loss of traction it is possible to cause damage to the transmission Do not attempt to shift when the rear wheels do not have traction Damage caused by misuse of the vehicle is not covered See your warranty book for additional information Limited Slip Rear Axle Your vehicle may have this feature A limited slip rear axle can give you additional traction on snow mud ice sand or gravel It works like a standard axle most of the time but when one of the rear wheels has no traction and the other does this feature will allow the wheel with traction to move the vehicle StabiliTrak System Your vehicle has an electronic stability control system called StabiliTrak It is an advanced computer controlled system that assists with directional control of the vehicle in difficult driving conditions StabiliTrak activates when the computer senses a discrepancy between your intended path and the direction the vehicle is actually traveling StabiliTrak selectively applies braking pressure at any one of the vehicle s brakes to help steer the vehicle in the direction which you are steering When the system activates the Traction Control System TCS StabiliTrak warning light on the instrument panel cluster flashes You may also hear a noise or feel vibration in the brake pedal This is normal Continue to steer the vehicle in the direction you want it to go If there is a probl
318. must be under the belt and the guide on top 1 29 A CAUTION A safety belt that is not properly worn may not provide the protection needed in a crash The person wearing the belt could be seriously injured The shoulder belt should go over the shoulder and across the chest These parts of the body are best able to take belt restraining forces 1 30 4 Buckle position and release the safety belt as described previously in this section Make sure that the shoulder belt crosses the shoulder To remove and store the comfort guide squeeze the belt edges together so that you can take them out of the guide Pull the guide upward to expose its storage clip and then slide the guide onto the clip Turn the guide and clip inward and slide them in between the seatback and the interior body leaving only the loop of the elastic cord exposed Safety Belt Use During Pregnancy Safety belts work for everyone including pregnant women Like all occupants they are more likely to be seriously injured if they do not wear safety belts A pregnant woman should wear a lap shoulder belt and the lap portion should be worn as low as possible below the rounding throughout the pregnancy The best way to protect the fetus is to protect the mother When a safety belt is worn properly it is more likely that the fetus will not be hurt in a crash For pregnant women as for anyone the key to making safety belts effective is wearing them p
319. n 3 106 Audio Steering Wheel Controls Left Side Steering Wheel Controls Right Side Steering Wheel Conirols Some audio controls can be adjusted at the steering wheel They include the following SRCE Source Press this button to switch between the radio AM FM XM if equipped CD HDD if available auxiliary input jack if connected USB and iPod if available and connected V Previous Next Press the previous or the next arrow to go to the previous or to the next radio station stored as a favorite When a CD is playing press either arrow to go to the previous or to the next track lt lt 1 Volume Press the plus or minus volume button to increase or to decrease the volume Mute Speech Recognition Press and release this button to silence the vehicle speakers only The audio of the wireless and wired headphones if your vehicle has these features does not mute Press and release this button again to turn the sound on If your vehicle has the navigation system press and hold this button for longer than one second to initiate speech recognition See Speech Recognition in the Navigation System manual for more information If your vehicle has OnStar press and hold this button for longer than one second to interact with the OnStar system If your vehicle also has the navigation system press and hold this button for longer than one second to initiate speech recognition an
320. n suffer permanent injuries or even death from heat stroke Always lock your vehicle whenever you leave it Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle Locking your doors can help prevent this from happening There are several ways to lock and unlock your vehicle From the inside use the manual lock levers located on the door panels near the windows Push down on the manual lock lever to lock the door To unlock the door pull up on the lever If the windows are down and the doors are locked do not reach in to manually unlock the vehicle because you will set off the alarm From the outside use the key or press the lock or unlock button on the Remote Keyless Entry RKE transmitter See Remote Keyless Entry RKE System Operation on page 2 7 for more information On vehicles with the Remote Keyless Access system the door unlocks by pulling the door handle when you have the transmitter with you See Keyless Access System Operation on page 2 9 for more information Central Door Unlocking System Your vehicle has a central door unlocking feature When unlocking the driver s door you can unlock the other doors by holding the key in the turned position for a few seconds or by quickly turning the key twice in the lock cylinder Power Door Locks The power door lock switches are located on the front doors n Unlock Press to unlock the doors a Lock Remove the k
321. n 2WD This could be caused by e Loss of wheel or vehicle speed e AWD system overheat e Certain vehicle electrical conditions This message turns off when the above conditions are no longer present and by resetting the warning message To reset the warning message turn the ignition off and then back on again after 30 seconds If the message stays on see your dealer retailer right away See All Wheel Drive AWD System on page 4 9 for more information Automatic Light Control Off This message displays when the automatic headlamps are turned off Automatic Light Control On This message displays when the automatic headlamps are turned on Battery Saver Active This message displays when the system detects that the battery voltage is dropping below expected levels The battery saver system starts reducing certain features of the vehicle that you may be able to notice At the point that the features are disabled this message is displayed It means that the vehicle is trying to save the charge in the battery Turn off all unnecessary accessories to allow the battery to recharge The normal battery voltage range is 11 5 to 15 5 volts You can monitor battery voltage on the DIC by pressing the vehicle information button until Battery Voltage is displayed 3 55 Battery Volts Low This message displays when the electrical system is charging less than 10 volts or the battery has been drained If this message appears
322. n a eiT 5 16 Engine Oil Life System nacen 5 19 Engine Air Cleaner Filter ccceeeeeeeeeneee ees 5 21 Automatic Transmission Fluid eeeeeee 5 25 Manual Transmission Fluid 0 00 5 25 Hydraulic Clutch eeann naai cae 5 26 Engine Coolant erie arrimer na EEN 5 27 Coolant Surge Tank Pressure Cap 00 5 30 Engine Overheating ccceeeeeeeeeeeeeeee teens 5 30 Overheated Engine Protection Operating Mode 5 32 Cooling System cceceeeceeeeeeeeeeeceeeeeeeeeee 5 33 Power Steering Fluid sceeseeeeeeeeeeee ees 5 38 Windshield Washer Fluid ceeeeeeeeee eee es 5 39 Brakes dreus oeat sede sareeives hegtea nace eer 5 40 Battery oi Savcesatinctnmaetsctedecncsnraduenmanbeaenceautenss 5 43 JUMP STAMINA sneen eiaa 5 44 All Wheel Drive ccceceeeeenee rererere 5 49 Rear AxI6 gaaer aart Ea Ea 5 50 Headlamp Aiming io 5 51 Bulb Replacement 0 eee 5 55 High Intensity Discharge HID Lighting 5 55 Halogen BUDS ticicecsccisataeaccneenaattnvengedaeneers 5 55 Front Turn Signal and Fog Lamps 06 5 5 56 License Plate Lamp seeeeeeeeeereeeeeeeee 5 56 Replacement Bulbs ceeceeeeeeeeeee eee ee eees 5 57 Windshield Wiper Blade Replacement 5 57 MPS E E E E A T 5 59 Winter Tile S ersen na EEE 5 60 Tire Sidewall Labeling ceeeeeeeeeeeeeeees 5 61 Tire
323. n may have an up shift light on the instrument panel This light will show you when to shift to the next higher gear for the best fuel economy When this light comes on you can shift to the next higher gear if weather road and traffic conditions allow For the best fuel economy accelerate slowly and shift when the light comes on While you accelerate it is normal for the light to go on and off if you quickly change the position of the accelerator Ignore the light when you downshift Parking Brake The parking brake pedal is located on the lower portion of the instrument panel to the left of the steering wheel To set the parking brake hold the regular brake pedal down with your right foot and push the parking brake pedal down with your left foot If the ignition is on the brake system warning light on the instrument panel cluster should come on If it does not you need to have your vehicle serviced See Brake System Warning Light on page 3 37 for more information To release the parking brake pull the release lever located to the left of the steering wheel on the instrument panel Notice Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts Make sure that the parking brake is fully released and the brake warning light is off before driving A warning chime will sound if the parking brake is set the ignition is on and the vehicle
324. nada also has a Mobility Program Call 1 800 GM DRIVE 463 7483 for details TTY users call 1 800 263 3830 Roadside Service In the United States or Canada call 1 800 882 1112 Text Telephone TTY U S only call 1 888 889 2438 Service is available 24 hours a day 365 days a year As the owner of a new Cadillac vehicle you are automatically enrolled in the Cadillac Roadside Service program Who Is Covered Roadside Service coverage is for the vehicle operator regardless of ownership In Canada a person driving this vehicle without the consent of the owner is not eligible for coverage Cadillac Owner Privileges The following services are provided in the U S and Canada up to 5 years 100 000 miles 160 000 km whichever occurs first and in Canada only up to a maximum coverage of 100 These services are provided at a nominal charge if the vehicle is no longer within the Powertrain warranty Roadside Service provides several Cadillac Owner Privileges at no charge throughout your Cadillac Powertrain Warranty 5 years 100 000 miles 160 000 km Emergency Road Service is performed on site for the following situations e Fuel Delivery Delivery of enough fuel for the vehicle to get to the nearest service station approximately 5 in Canada In Canada for safety reasons propane and other alternative fuels will not be provided through this service e Lock out Service Lock out service will be co
325. nd wheel assembly The TPMS sensors monitor the air pressure in the vehicle s tires and transmits the tire pressure readings to a receiver located in the vehicle Using the Driver Information Center DIC the driver can also check tire pressure levels using the DIC For additional information and details about the DIC operation and displays see DIC Operation and Displays on page 3 48 and DIC Warnings and Messages on page 3 54 5 71 When a low tire pressure condition is detected the TPMS illuminates the low tire pressure warning light located on the instrument panel cluster A DIC warning message to check the pressure in a specific tire is also shown on the DIC display screen The low tire pressure warning light and the DIC warning message come at each ignition cycle until the tires are inflated to the correct inflation pressure The low tire pressure warning light may come on in cool weather when the vehicle is first started and then turn off as you start to drive This could be an early indicator that the air pressure in the tire s are getting low and need to be inflated to the proper pressure 5 72 The Tire and Loading Information label attached to your vehicle shows the size of your vehicle s original equipment tires and the correct inflation pressure for the tires when they are cold See Loading Your Vehicle on page 4 22 for an example of the Tire and Loading Information label and its location on your vehicle
326. ne Coolant Temperature Warning Light This light will come on when you first start the vehicle as a check to let you know that the light is working RAAT It will go out after a few seconds If the light does not come on see your dealer retailer If the light does not go out or if the light comes on and stays on while you are driving your vehicle may have a problem with the cooling system You should stop the vehicle and turn off the engine as soon as possible to avoid damage to the engine A warning chime will also sound when this light is on See Engine Overheating on page 5 30 for more information Engine Coolant Temperature Gage United States Canada This gage shows the engine coolant temperature If the engine coolant overheats the engine coolant temperature warning light will come on See Engine Overheating on page 5 30 and Engine Coolant Temperature Warning Light on page 3 39 for more information 3 39 Tire Pressure Light Your vehicle has a tire pressure light This light comes on briefly when the engine is started and provides information about tire pressures and the Tire Pressure Monitoring System When the Light is Solid This indicates that one or more of your tires are significantly underinflated A tire pressure message in the Driver Information Center DIC may accompany the light See DIC Warnings and Messages on page 3 54 for more information Stop and check your tires as soon as it i
327. ne Program using the toll free telephone number or write them at the following address BBB Auto Line Program Council of Better Business Bureaus Inc 4200 Wilson Boulevard Suite 800 Arlington VA 22203 1838 Telephone 1 800 955 5100 This program is available in all 50 states and the District of Columbia Eligibility is limited by vehicle age mileage and other factors General Motors reserves the right to change eligibility limitations and or discontinue its participation in this program STEP THREE Canadian Owners General Motors Participation in the Mediation Arbitration Program In the event that you do not feel your concerns have been addressed after the following the procedure outlined in Steps One and Two General Motors of Canada Limited wants you to be aware of its participation in a no charge mediation Arbitration program General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory related vehicle service claims The program provides for the review of the facts involved by an impartial third party arbiter and may include an informal hearing before the arbiter The program is designed so that the entire dispute settlement process from the time you file your complaint to the final decision should be completed in approximately 70 days We believe our impartial program offers advantages over courts in most jurisdictions because it is informal quick and free of charge F
328. never exceed XXX kg or XXX Ibs on your vehicle s placard 2 Determine the combined weight of the driver and passengers that will be riding in your vehicle 3 Subtract the combined weight of the driver and passengers from XXX kg or XXX Ibs 4 23 4 The resulting figure equals the available amount of cargo and luggage load capacity For example if the XXX amount equals 1400 Ibs and there will be five 150 Ib passengers in your vehicle the amount of available cargo and luggage load capacity is 650 Ibs 1400 750 5 x 150 650 Ibs 5 Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4 Example 1 6 If your vehicle will be towing a trailer the load from your trailer will be transferred to your Item Description Total vehicle Consult this manual to determine how Vehicle Capacity 1 000 Ib this reduces the available cargo and luggage A Weight for 453 k S load capacity of your vehicle Example 1 9 See Towing a Trailer on page 4 29 for Subtract Occupant important information on towing a trailer Weight 150 Ibs 300 Ibs 136 kg towing safety rules and trailering tips 68 kg x2 Available Occupant and Cargo Weight 700 bs 317 kg 4 24 Example 2 Example 3 Item Description Total Item Description Totali Vehicle Capacity Vehicle Capaci
329. ng and ventilation for the vehicle can be controlled with this system b Power Press this button to turn the climate control system on or off When the climate control system is turned off the air inlet defaults to outside air Automatic Operation AUTO Automatic When this button is pressed and the temperature is set the system automatically controls the inside temperature the air delivery mode the air conditioning compressor and the fan speed When the indicator light is on the system is in full automatic operation If the air delivery mode or fan setting is manually adjusted the auto indicator turns off and displays will show the selected settings 1 Press the AUTO button 2 Adjust the temperature to a comfortable setting between 60 F 15 5 C and 90 F 32 2 C Choosing the coldest or warmest temperature setting will not cause the system to heat or cool any faster If the system is set at the warmest temperature setting it remains in manual mode at that temperature and it will not go into automatic mode In cold weather the system starts at reduced fan speeds to avoid blowing cold air into the vehicle until warmer air is available The system begins blowing air at the floor but may change modes automatically as the vehicle warms up to maintain the chosen temperature setting The length of time the system needs to warm up depends on the o
330. ng soap Do not use cleaning agents that are petroleum based or that contain acid or abrasives as they can damage the paint metal or plastic on your vehicle Approved cleaning products can be obtained from your dealer retailer See Vehicle Care Appearance Materials on page 5 119 Follow all manufacturers directions regarding correct product usage necessary safety precautions and appropriate disposal of any vehicle care product Rinse the vehicle well before washing and after to remove all cleaning agents completely If they are allowed to dry on the surface they could stain Dry the finish with a soft clean chamois or an all cotton towel to avoid surface scratches and water spotting High pressure car washes may cause water to enter the vehicle Avoid using high pressure washes closer than 12 inches 30 cm to the surface of the vehicle Use of power washers exceeding 1 200 psi 8 274 kPa can result in damage or removal of paint and decals 5 115 Cleaning Exterior Lamps Lenses Use only lukewarm or cold water a soft cloth and a car washing soap to clean exterior lamps and lenses Follow instructions under Washing Your Vehicle on page 5 115 Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish You can get approved cleaning products from your dealer retailer See Vehicle Care Appearance Materials on page 5 119 If your vehicle has a basecoat
331. ng the engine in a closed in place or with the climate control system off can cause deadly carbon monoxide CO See Engine Exhaust on page 2 47 5 Start the vehicle See Starting the Engine on page 2 34 for more information The vehicle must be running while using the air compressor 1 Do a safety check before proceeding See f a ZN CAUTION Tire Goes Flat on page 5 83 2 Unwrap the air only hose G from the bottom of Inflating something too much can make it the air compressor explode and you or others could be injured Be sure to read the inflator instructions and inflate the tire to its recommended pressure Do not exceed 36 psi 248 kPa 3 Attach the air only hose G onto the valve stem to secure into place 4 Plug the air compressor accessory plug E into an accessory power outlet in the vehicle See Accessory Power Outlet s on page 3 21 for more 6 Turn the selector switch A clockwise to the information air only position 7 Push the On Off button B 5 91 8 Inflate the tire up to the recommended inflation 11 Disconnect the air only hose G and wrap the hose pressure using the air pressure gage C on the in the bottom of the sealant and compressor kit top of the unit 12 Place the equipment in the original location in the The pressure gage read high while the compressor trunk of your vehicle is running Turn the compressor off to get an accurate reading Removal and
332. ngine Oil Pressure Gage Canada United States Your vehicle may have an engine oil pressure gage It shows the engine oil pressure in psi pounds per square inch when the engine is running Canadian vehicles indicate pressure in kPa kilopascals Oil pressure may vary with engine speed outside temperature and oil viscosity but if readings are outside the normal operating range the oil pressure light will come on See Oil Pressure Light on page 3 43 for more information A reading outside the normal operating range may be caused by a dangerously low oil level or some other problem causing low oil pressure Check your oil as soon as possible See Oil pressure Low Stop Engine under DIC Warnings and Messages on page 3 54 and Engine Oil on page 5 16 A CAUTION Do not keep driving if the oil pressure is low If you do your engine can become so hot that it catches fire You or others could be burned Check your oil as soon as possible and have your vehicle serviced Notice Lack of proper engine oil maintenance may damage the engine The repairs would not be covered by your warranty Always follow the maintenance schedule in this manual for changing engine oil Security Light For information regarding this light and the vehicle s security system see Theft Deterrent System on page 2 27 Fog Lamp Light The fog lamp light will come on when the fog 9 lamps are in use The light will go out when the fog
333. ning A a Fe SUEY ese Scherer ee Power WiNdOWS oeecccccccccccccecccccececcccceeeeccceseecs 2 04 Mirrors cetteeeeeeeeteneeeseeees settee een setteeeeeeees 2 49 SUN VISOMS aae e eE peamiamporamclueedaiedsess 2 26 Automatic Dimming Rearview Mirror with Theft Deterrent Systems 997 OnStar TEET A E ES 2 49 sake ee a aes Outside Power Mirrors cc0cccceccseeeeeeneees 2 49 S st SESE SYSTEMI anenentsnraicetetesaencensieete a Park Tilt Mirrors c ccsececeeseeeceeeeeeeeeeeeees 2 50 immobilizer Operation Key Access 228 QUIS Convex MIOT eesse en Immobilizer Operation Keyless Access 1S O a A ae eC 2 1 Section 2 Features and Controls Object Detection Systems creer 2 51 Storage Areas eener eee neers eeeeen ees 2 61 Ultrasonic Rear Parking Assist URPA 2 51 Glove BOX oc cnnr itil sain calieaian ae E sect tonnes 2 61 OnStar System 0 20 2 cece cccc ee inanir enneren 2 53 ts la a lt S at nstrument Panel Storage ssierisrroremisrisisss Universal Home Remote System o i 2 56 Center Console Storage eeceeeeeeeeeeeee tenes 2 61 Universal Home Remote System 2 56 l Convenience Net c ceeeeeeeeeeeeeeeeeeeeeeeeaes 2 62 Universal Home Remote System Operation With One Triangular LED 0 c0cceeeeeee 9 57 SUNMOOP iiaeie an a aE iets SEAS 2 62 CAUTION Continued A CAUTION the vehicle move The windows will function with the keyless acce
334. not an audio output do not plug the headphone set into the front auxiliary input jack An external audio device such as an iPod laptop computer MP3 player etc can be connected to the auxiliary input jack for use as another source for audio listening Set up any auxiliary device while the vehicle is stopped See Defensive Driving on page 4 2 for more information on driver distraction To use a portable audio player connect a 3 5 mm 1 8 inch cable to the radio s front auxiliary input jack The radio automatically detects the device and Aux Input Device displays The device begins playing over the vehicle speakers If an auxiliary device has already been connected press the radio s AUX or CD AUX button VoL Volume Power Turn clockwise or counterclockwise to increase or decrease the volume of the portable player Use the portable device to make additional volume adjustments FM AM Press to listen to the radio when a portable audio device is playing The portable audio device continues playing until you stop it 3 99 CD or CD AUX CD Auxiliary Press to play a CD when a portable audio device is playing Press again to start playing audio from the connected portable audio player If a portable audio player is not connected No Aux Device displays Using the Radio Controls to Connect and Control Your iPod You can control your iPod using the radio buttons and knobs and display your iPod song inform
335. nrelated to the crash This will help guard against post crash legal action If you need roadside assistance call GM Roadside Assistance See Roadside Service on page 7 6 for more information If your vehicle cannot be driven know where the towing service will be taking it Get a card from the tow truck operator or write down the driver s name the service s name and the phone number Remove any valuables from your vehicle before it is towed away Make sure this includes your insurance information and registration if you keep these items in your vehicle Gather the important information you will need from the other driver Things like name address phone number drivers license number vehicle license plate vehicle make model and model year Vehicle Identification Number VIN insurance company and policy number and a general description of the damage to the other vehicle If possible call your insurance company from the scene of the crash They will walk you through the information they will need If they ask for a police report phone or go to the police department headquarters the next day and you can get a copy of the report for a nominal fee In some states provinces with no fault insurance laws a report may not be necessary This is especially true if there are no injuries and both vehicles are driveable Choose a reputable collision repair facility for your vehicle Whether you select a GM dealer retail
336. nstrument Panel Vinyl and Other Plastic Surfaces ccceceeeeeeeeeneee eee eeeeeeee 5 114 Wood Panels ivscictecceues sieeve a ASEE 5 114 Speaker Covers airmen ean esee oi 5 114 5 2 Service and Appearance Care Care of Safety Belts anenencceeeeeeeeeeee 5 114 WeathersttipS csse sismiriisiisrearniesii urena 5 115 Washing Your Vehicle 2 a 5 115 Cleaning Exterior Lamps Lenses 0655 5 116 Finish Cane icissz sein tics rannen E sedan sa cons eaten 5 116 Windshield and Wiper Blades 005 5 117 Aluminum or Chrome Plated Wheels AMO TMM ssrin e aa ae 5 117 OS an ee a A E tees 5 118 Sheet Metal Damage 6 ceeeeeeeeeeeeeee ees 5 118 Finish Damage inrano 5 118 Underbody Maintenance 0seeeeeeeee es 5 119 Chemical Paint Spotting eeeeeeeeeee eee 5 119 Vehicle Care Appearance Materials 5 119 Vehicle Identification eee 5 120 Vehicle Identification Number VIN 5 120 Service Parts Identification Label 5 121 Electrical System 2 eee 5 121 Add On Electrical Equipment 0 00 5 121 Windshield Wiper Fuses seeeeeeeeenee ees 5 121 Power Windows and Other Power Options 5 122 Fuses and Circuit Breakers eeeeeeeee ees 5 122 Underhood Fuse Block assener 5 122 Rear Compartment Fuse Block 655 5 126 Capacities and S
337. nt cool down 2 Wipe the cap and the top of the reservoir clean 3 Unscrew the cap and wipe the dipstick with a clean rag 4 Replace the cap and completely tighten it 5 Remove the cap again and look at the fluid level on the dipstick The level should be at the FULL COLD mark If necessary add only enough fluid to bring the level up to the mark What to Use To determine what kind of fluid to use see Recommended Fluids and Lubricants on page 6 11 Always use the proper fluid Notice Use of the incorrect fluid may damage your vehicle and the damages may not be covered by your warranty Always use the correct fluid listed in Recommended Fluids and Lubricants on page 6 11 Windshield Washer Fluid What to Use When you need windshield washer fluid be sure to read the manufacturer s instructions before use If you will be operating your vehicle in an area where the temperature may fall below freezing use a fluid that has sufficient protection against freezing Adding Washer Fluid The Washer Fluid Low Add Fluid message will appear on the Driver Information Center DIC when the fluid level is low See DIC Warnings and Messages on page 3 54 for more information Open the cap with the washer symbol on it Add washer fluid until the tank is full See Engine Compartment Overview on page 5 14 for reservoir location Notice e When using concentrated washer fluid follow the manufacturer s instructions for
338. ny additional material from the seat such as blankets cushions seat covers seat heaters or seat massagers before reinstalling or securing the child restraint If the on indicator is still lit secure the child in the child restraint in a rear seat position in the vehicle and check with your dealer retailer To remove the child restraint unbuckle the vehicle s safety belt and let it go back all the way Airbag System Your vehicle has the following airbags e A frontal airbag for the driver e A frontal airbag for the right front passenger e A seat mounted side impact airbag for the driver e A seat mounted side impact airbag for the right front passenger e A roof rail airbag for the driver and the passenger seated directly behind the driver e A roof rail airbag for the right front passenger and the passenger seated directly behind the right front passenger All of the airbags in your vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening For frontal airbags the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger With seat mounted side impact airbags the word AIRBAG will appear on the side of the seatback closest to the door 1 55 With roof rail airbags the word AIRBAG will appear along the headliner or trim Airbags are designed to supplement the protection provided
339. ny cleaners contain solvents that may become concentrated in your vehicle s breathing space Before using cleaners read and adhere to all safety instructions on the label While cleaning your vehicle s interior maintain adequate ventilation by opening your vehicle s doors and windows Dust may be removed from small buttons and knobs using a small brush with soft bristles 5 112 Your dealer retailer has a product for cleaning your vehicle s glass Should it become necessary you can also obtain a product from your dealer retailer to remove odors from your vehicle s upholstery Do not clean your vehicle using e A knife or any other sharp object to remove a soil from any interior surface e A stiff brush It can cause damage to your vehicle s interior surfaces e Heavy pressure or aggressive rubbing with a cleaning cloth Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal e Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt For liquid cleaners about 20 drops per gallon 3 78 L of water is a good guide Use only mild neutral pH soaps e Too much cleaner that saturates the upholstery e Organic solvents such as naptha alcohol etc that can damage your vehicle s interior Fabric Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt A canister vacuum with
340. ommended pressure cannot be reached after 15 minutes the vehicle should not be driven farther Damage to the tire is severe and the sealant will not be effective Remove the air compressor plug from the accessory power outlet and unscrew the inflating hose from the tire valve See Roadside Service on page 7 6 12 Push the on off switch D to the O off position 13 The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire Steps 13 through 20 must be done right after Step 11 14 15 16 17 Unplug the air compressor accessory plug C from the accessory power outlet in the vehicle Disconnect the sealant air hose from the tire valve stem by turning it counterclockwise and replace the tire valve stem cap Be careful when handling the tire inflator components as they may be hot after usage Wrap the sealant air hose around the air compressor channel to stow it in its original location Stow the air compressor accessory plug back in the air compressor To do this wrap the air compressor accessory plug snap in the plug and then push in the bottom and then the top of the wrapped air compressor accessory plug 5 97 18 If the flat tire was able to inflate to the x recommended inflation A CAUTION pressure remove the maximum speed Storing the tire sealant and compressor label from the sealant kit or other equipment in the passenger c
341. ompany s collision policy repair limits as you have no contractual limits with that company In such cases you can have control of the repair and parts choices as long as cost stays within reasonable limits Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying General Motors If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer retailer or General Motors 7 14 To contact NHTSA you may call the Vehicle Safety Hotline toll free at 1 888 327 4236 TTY 1 800 424 9153 go to http Awww safercar gov or write to Administrator NHTSA 400 Seventh Street SW Washington D C 20590 You can also obtain other information about motor vehicle safety from http www safercar gov Reporting Safety Defects to the Canadian Government If you live in Canada and you believe that your vehicle has a safety defect notify Transport Canada immediately in addition to notifying General Motors of Canada Limited Call them at 1 800 333 0510 or write to Transport Canada Road Safety
342. ompartment To use the lighter push it in all the way and let go When it is ready it will pop back out by itself To empty the ashtrays grip the edges of the bin and pull it straight out of the housing To reinstall push the tray back into place Notice Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot Damage from overheating can occur to the lighter or heating element or a fuse could be blown Do not hold a cigarette lighter in while it is heating Notice f you put papers pins or other flammable items in the ashtray hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle Never put flammable items in the ashtray 3 22 Analog Clock The analog clock is located on the instrument panel above the radio The clock is not connected with any other vehicle system and runs by itself To adjust the clock 1 Locate the adjustment buttons directly below the clock face 2 Push and hold the right adjustment button to move the clock hands forward or the left adjustment button to make the clock hands go backward Holding either button down will cause the clock to advance faster Release the button before the desired time is reached 3 Push and release either button to adjust the time by one minute increments until the desired time is reached Climate Controls Dual Climate Control System The heating cooli
343. on located below the displayed page numbers 4 Press the FAV button or let the menu time out to return to the original main radio screen showing the radio station frequency labels and to begin the process of programming your favorites for the chosen number of pages Setting the Tone Bass Midrange Treble BASS MID TREB Bass Midrange or Treble To adjust bass midrange or treble press the TUNE TONE knob until the tone control labels display Continue pressing to highlight the desired label or press the pushbutton positioned under the desired label Turn the TUNE TONE knob clockwise or counterclockwise to adjust the highlighted setting The highlighted setting can also be adjusted by pressing either SEEK arrow gt gt FWD or lt lt REV button until the desired levels are obtained If a station s frequency is weak or has static decrease the treble To quickly adjust bass midrange or treble to the middle position press the pushbutton positioned under the BASS MID or TREB label for more than two seconds A beep may sound and the level adjusts to the middle position To quickly adjust all tone and speaker controls to the middle position press the TUNE TONE knob for more than two seconds Adjusting the Speakers Balance Fade BAL FADE Balance Fade To adjust balance or fade press the TUNE TONE knob until the speaker control labels display Continue pressing to highlight the desired label or press the pushb
344. on on acceleration or stumbling on acceleration these conditions might go away once the engine is warmed up This will be detected by the system and cause the light to turn on If you experience one or more of these conditions change the fuel brand you use It will require at least one full tank of the proper fuel to turn the light off If none of the above steps have made the light turn off your dealer retailer can check the vehicle Your dealer retailer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed Emissions Inspection and Maintenance Programs Some state provincial and local governments have or might begin programs to inspect the emission control equipment on your vehicle Failure to pass this inspection could prevent you from getting a vehicle registration Here are some things you need to know to help your vehicle pass an inspection Your vehicle will not pass this inspection if the check engine light is on or not working properly Your vehicle will not pass this inspection if the OBD on board diagnostic system determines that critical emission control systems have not been completely diagnosed by the system The vehicle would be considered not ready for inspection This can happen if you have recently replaced the battery or if the battery has run down The diagnostic system is designed to evaluate critical emission control systems during n
345. on your skin flush the place with water and get medical help immediately Do not connect positive to negative or you will get a short that would damage the battery and maybe other parts too And do not connect the negative cable to the negative terminal on the dead battery because this can cause sparks 5 47 6 Connect the red positive cable to the positive terminal of the dead battery Use a remote positive terminal if the vehicle has one the positive terminal of the good battery Use a 5 48 Do not let the other end touch metal Connect it to remote positive terminal if the vehicle has one 10 11 Now connect the black negative cable to the negative terminal of the good battery Use a remote negative terminal if the vehicle has one Do not let the other end touch anything until the next step The other end of the negative cable does not go to the dead battery It goes to a heavy unpainted metal engine part or to a remote negative terminal on the vehicle with the dead battery Connect the other end of the negative cable at least 18 inches 45 cm away from the dead battery but not near engine parts that move The electrical connection is just as good there and the chance of sparks getting back to the battery is much less Use a remote negative terminal if the vehicle has one Your vehicle s remote negative
346. ood Z CAUTION Things that burn can get on hot engine parts Z CAUTION and start a fire These include liquids like fuel An electric fan under the hood can start up oil coolant brake fluid windshield washer and other fluids and plastic or rubber You or others could be burned Be careful not to drop ane NUNS YOU even when thie engine isnot or spill things that will burn onto a hot engine running Keep hands clothing and tools away from any underhood electric fan Hood Release To open the hood do the following 1 Pull the hood release lever with this symbol on it It is located inside the vehicle on the lower left side of the instrument panel 2 Then go to the front of the vehicle and find the secondary hood release lever The lever is located under the front edge of the grille near the center Push the release lever up and raise the hood Before closing the hood be sure all the filler caps are on properly Then pull the hood down and close it firmly Engine Compartment Overview When you open the hood here is what you will see 5 14 Windshield Washer Fluid Reservoir See Adding Washer Fluid under Windshield Washer Fluid on page 5 39 Underhood Fuse Block See Underhood Fuse Block on page 5 122 Remote Positive Terminal See Jump Starting on p
347. or example Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration NHTSA which grades tires by treadwear traction and temperature performance This applies only to vehicles sold in the United States The grades are molded on the sidewalls of most passenger car tires The Uniform Tire Quality Grading UTQG system does not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches 25 to 30 cm or to some limited production tires While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria TPC standards 5 80 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and a half 1 5 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AA A B C The t
348. or further information concerning eligibility in the Canadian Motor Vehicle Arbitration Plan CAMVAP call toll free 1 800 207 0685 Alternatively you may call the General Motors Customer Communication Centre 1 800 263 3777 English 1 800 263 7854 French or you may write to the Mediation Arbitration Program at the following address Your inquiry should be accompanied by your Vehicle Identification Number VIN Mediation Arbitration Program c o Customer Communication Centre General Motors of Canada Limited Mail Code CA1 163 005 1908 Colonel Sam Drive Oshawa Ontario L1H 8P7 Online Owner Center United States only The Owner Center is a resource for your GM ownership needs Specific vehicle information can be found in one place The Online Owner Center allows you to e Get e mail service reminders e Access information about your specific vehicle including tips and videos and an electronic version of this owner manual e Keep track of your vehicle s service history and maintenance schedule e Find GM dealers retailers for service nationwide e Receive special promotions and privileges only available to members Refer to www MyGMLink com on the web for updated information and to register your vehicle My GM Canada Canada only My GM Canada is a password protected section of gmcanada com where you can save information on GM vehicles get personalized offers and use handy tools and forms with greater eas
349. orhome see Recreational Vehicle Towing following Recreational Vehicle Towing Recreational vehicle towing means towing your vehicle behind another vehicle such as behind a motorhome The two most common types of recreational vehicle towing are known as dinghy towing towing your vehicle with all four wheels on the ground and dolly towing towing your vehicle with two wheels on the ground and two wheels up on a device known as a dolly With the proper preparation and equipment many vehicles can be towed in these ways See Dinghy Towing and Dolly Towing following Here are some important things to consider before you Dolly Towing do recreational vehicle towing e What is the towing capacity of the towing vehicle Be sure you read the tow vehicle manufacturer s recommendations e How far will you tow Some vehicles have restrictions on how far and how long they can tow e Do you have the proper towing equipment See your dealer retailer or trailering professional for additional advice and equipment recommendations e ls your vehicle ready to be towed Just as you would prepare your vehicle for a long trip you ll want to make sure your vehicle is prepared to be towed See Before Leaving on a Long Trip on page 4 16 Dinghy Towing Notice If you tow your vehicle with all four wheels on the ground the drivetrain components could Your vehicle can be towed using a dolly To tow your be dam
350. ormal driving This can take several days of routine driving If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness your dealer retailer can prepare the vehicle for inspection Oil Pressure Light Your vehicle may have this feature If the vehicle has an oil problem this light may stay on after the engine is started or come on while you are driving This light indicates that oil is not going through the engine quickly enough to keep it lubricated The engine could be low on oil or could have some other oil problem Have it fixed right away 3 43 The oil light could also come on in the following situations e The light will come on briefly when the ignition is turned on to show that it is working properly If it does not come on with the ignition on there may be a problem with the fuse or bulb Have it fixed right away e Sometimes when the engine is idling at a stop a chime will sound and the light may blink on and off This is normal A CAUTION Do not keep driving if the oil pressure is low If you do your engine can become so hot that it catches fire You or others could be burned Check your oil as soon as possible and have your vehicle serviced Notice Lack of proper engine oil maintenance may damage the engine The repairs would not be covered by your warranty Always follow the maintenance schedule in this manual for changing engine oil 3 44 E
351. ormation You may temporarily disable the keyless locking feature by pressing the door unlock switch for three seconds on an open door Keyless locking will then remain disabled until a door lock switch is pressed or until the power mode transitions from the off power mode To select whether the horn sounds or the lights flash when the vehicle is locked see Remote Door Lock earlier in this section Press the customization button until Keyless Locking appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off default The keyless locking feature will be disabled On The keyless locking feature will be enabled 3 74 The doors will automatically lock several seconds after you turn the ignition off remove a keyless access transmitter from the interior of the vehicle and close all of the doors No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Keyless Unlock If your vehicle has the keyless access system this feature allows you to select which doors will automatically unlock when you approach the vehicle with the keyless access transmitter and open the driver s door See Keyless Access System Operation on page 2 9 for more information To select whether the lig
352. ors are located under the covers on the rear seatback filler panel Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached or if the instructions that come with the child restraint say that the top tether must be attached Accident statistics show that children are safer if they are restrained in the rear rather than the front seat See Where to Put the Restraint on page 1 42 for additional information 1 45 Securing a Child Restraint Designed for the LATCH System A CAUTION If a LATCH type child restraint is not attached to anchors the restraint will not be able to protect the child correctly In a crash the child could be seriously injured or killed Make sure that a LATCH type child restraint is properly installed using the anchors or use the vehicle s safety belts to secure the restraint following the instructions that came with that restraint and also the instructions in this manual 1 46 A CAUTION Each top tether anchor and lower anchor in the vehicle is designed to hold only one child restraint Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash A child or others could be injured if this happens
353. ors are matched to the tire wheel positions in the following order driver side front tire passenger side front tire passenger side rear tire and driver side rear tire using a TPMS diagnostic tool See your dealer retailer for service 5 73 The TPMS sensors can also be matched to each tire wheel position by increasing or decreasing the tire s air pressure If increasing the tire s air pressure do not exceed the maximum inflation pressure indicated on the tire s sidewall To decrease the tire s air pressure use the pointed end of the valve cap a pencil style air pressure gage or a key You have two minutes to match the first tire wheel position and five minutes overall to match all four tire wheel positions If it takes longer than two minutes to match the first tire and wheel or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over The TPMS matching process is outlined below 1 Set the parking brake 2 Turn the ignition switch to ON RUN with the engine off 3 Press the Remote Keyless Entry RKE transmitter s lock and unlock buttons at the same time for approximately five seconds The horn sounds twice to signal the receiver is in relearn mode and Tire Learning Active message displays on the DIC screen 5 74 10 Vil Start with the driver side front tire Remove the valve cap from the valve stem Activate the TPMS sensor by
354. ote start feature is not enabled See Remote Start under DIC Vehicle Customization on page 3 68 The engine will turn off during a remote vehicle start if the coolant temperature gets too high or the oil pressure is too low Your vehicle was shipped from the factory with the remote vehicle start system enabled The system may be disabled through the Driver Information Center DIC See Remote Start under DIC Vehicle Customization on page 3 68 for additional information See Engine Exhaust on page 2 47 for important safety information when using remote start in a closed garage Remote Start Ready If your vehicle does not have the remote vehicle start feature it may have the remote start ready feature This feature allows your dealer retailer to add the manufacturer s remote vehicle start feature See your dealer retailer if you would like to add the manufacturer s remote vehicle start feature to your vehicle Doors and Locks Door Locks A CAUTION Unlocked doors can be dangerous e Passengers especially children can easily open the doors and fall out of a moving vehicle When a door is locked the handle will not open it You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked So wear safety belts properly and lock the doors whenever you drive Young children who get into unlocked vehicles may be unable to get out A child can be overcome by extreme heat and ca
355. ounted side impact airbags there are airbag modules in the side of the front seatbacks closest to the door For vehicles with roof rail airbags there are airbag modules in the ceiling of the vehicle near the side windows that have occupant seating positions How Does an Airbag Restrain In moderate to severe frontal or near frontal collisions even belted occupants can contact the steering wheel or the instrument panel In moderate to severe side collisions even belted occupants can contact the inside of the vehicle Airbags supplement the protection provided by safety belts Frontal airbags distribute the force of the impact more evenly over the occupant s upper body stopping the occupant more gradually Seat mounted 1 62 side impact and roof rail airbags distribute the force of the impact more evenly over the occupant s upper body But airbags would not help in many types of collisions primarily because the occupant s motion is not toward those airbags See When Should an Airbag Inflate on page 1 60 for more information Airbags should never be regarded as anything more than a supplement to safety belts What Will You See After an Airbag Inflates After the frontal airbags and seat mounted side impact airbags inflate they quickly deflate so quickly that some people may not even realize an airbag inflated Roof rail airbags may still be at least partially inflated for some time after they deploy Some components
356. ounted side impact and roof rail airbags will inflate if the crash severity is above the system s designed threshold level The threshold level can vary with specific vehicle design Seat mounted side impact airbags are not intended to inflate in frontal impacts near frontal impacts rollovers or rear impacts Roof rail airbags are not intended to inflate in rollovers or rear impacts A seat mounted side impact airbag is intended to deploy on the side of the vehicle that is struck Both roof rail airbags will deploy when either side of the vehicle is struck or ina severe frontal impact In any particular crash no one can say whether an airbag should have inflated simply because of the damage to a vehicle or because of what the repair costs were For frontal airbags inflation is determined by what the vehicle hits the angle of the impact and how quickly the vehicle slows down For seat mounted side impact and roof rail airbags deployment is determined by the location and severity of the side impact 1 61 What Makes an Airbag Inflate In a deployment event the sensing system sends an electrical signal triggering a release of gas from the inflator Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy The inflator the airbag and related hardware are all part of the airbag module Frontal airbag modules are located inside the steering wheel and instrument panel For vehicles with seat m
357. our tires can cause overheating as a result of too much flexing You could have an air out and a serious accident See Loading Your Vehicle on page 4 22 CAUTION Continued 5 59 Low Profile Tires If your vehicle has 235 50ZR18 or P235 50R18 size tires they are classified as low profile tires These tires are designed for very responsive driving on wet or dry pavement You may also notice more road noise with low profile performance tires and that they tend to wear faster Notice lf your vehicle has low profile tires they are more susceptible to damage from road hazards or curb impact than standard profile tires Tire and or wheel assembly damage can occur when coming into contact with road hazards like potholes or sharp edged objects or when sliding into a curb Your vehicle warranty does not cover this type of damage Keep tires set to the correct inflation pressure and when possible avoid contact with curbs potholes and other road hazards 5 60 Winter Tires If you expect to drive on snow or ice covered roads often you may want to get winter tires for your vehicle All season tires provide good overall performance on most surfaces but they may not offer the traction you would like or the same level of performance as winter tires on snow or ice covered roads Winter tires in general are designed for increased traction on snow and ice covered roads With winter tires there may be decreased dry road trac
358. our vehicle any heavier than the Gross Vehicle Weight Rating GVWR or either the maximum front or rear Gross Axle Weight Rating GAWR If you do parts on your vehicle can break and it can change the way your vehicle handles These could cause you to lose control and crash Also overloading can shorten the life of your vehicle Tire and Loading Information Label SEE OWNER S MANUAL FOR ADDITIONAL INFORMATION Example Label A vehicle specific Tire and Loading Information label is attached to the vehicle s center pillar B pillar With the driver s door open you will find the label attached below the door lock post striker The Tire and Loading Information label shows the number of occupant seating positions A and the maximum vehicle capacity weight B in kilograms and pounds The Tire and Loading Information label also shows the tire size of the original equipment tires C and the recommended cold tire inflation pressures D For more information on tires and inflation see Tires on page 5 59 and Inflation Tire Pressure on page 5 67 There is also important loading information on the Certification label It tells you the Gross Vehicle Weight Rating GVWR and the Gross Axle Weight Rating GAWR for the front and rear axle see Certification Label later in this section Steps for Determining Correct Load Limit 1 Locate the statement The combined weight of occupants and cargo should
359. ove the device if it is contacting your vehicle and do not spin your wheels If you do find traction devices that will fit install them on the rear tires If a Tire Goes Flat It is unusual for a tire to blowout while you are driving especially if you maintain your tires properly See Tires on page 5 59 lf air goes out of a tire It is much more likely to leak out slowly But if you should ever have a blowout here are a few tips about what to expect and what to do If a front tire fails the flat tire will create a drag that pulls the vehicle toward that side Take your foot off the accelerator pedal and grip the steering wheel firmly Steer to maintain lane position and then gently brake to a stop well out of the traffic lane A rear blowout particularly on a curve acts much like a skid and may require the same correction you would use in a skid In any rear blowout remove your foot from the accelerator pedal Get the vehicle under control by steering the way you want the vehicle to go It may be very bumpy and noisy but you can still steer Gently brake to a stop well off the road if possible 5 83 If a tire goes flat and your vehicle has a compact spare tire see Changing a Flat Tire on page 5 102 This information shows you how to use your vehicle s tire changing equipment and how to change a flat tire safely A CAUTION Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without
360. ow the Shuffle label to play the tracks of a current disc in random order Press the pushbutton again to turn Shuffle off Shuffle Off displays 5 The CD resumes normal playback To insert multiple CDs do the following 1 Press and hold this button for five seconds A beep sounds and Load All Discs displays 2 Follow the displayed instruction on when to insert the discs The CD player takes up to six CDs 3 Press the Load button again to cancel loading more CDs If the ignition or radio is turned off while a CD in the player it stays in the player When the ignition or radio is turned on the CD starts playing where it stopped if it was the last selected audio source When a CD is inserted the disc number displays on the upper right side of the screen and the track number displays at the left and center of the screen The Shuffle and Disc labels appear below Press the pushbuttons located under the Disc label to change to another disc The CD begins playback of the first track on the selected disc As each new track starts to play the track number displays in the left and center of the screen Shuffle Press the pushbutton located below the Shuffle label to play the tracks of a CD in random order Press again to turn Shuffle off Shuffle Off displays 3 87 A Eject To eject the disc that is currently playing press and release Ejecting Disc displays and a beep sounds Once the disc is ejected Remove Disc display
361. ows the setting high medium or low Press either button to start that feature at the highest setting Each press of the button decreases the setting To turn the feature off press the button until the light turns off The heated or ventilated seats shut off when the vehicle is turned off Memory Seat and Mirrors The buttons for this feature are located on the driver s door 1 Saves the seating position for driver 1 2 Saves the seating position for driver 2 J Recalls the easy exit position To program the buttons 1 Adjust the driver s seat including the seatback recliner and both outside mirrors 2 Press and hold button 1 for at least three seconds Two beeps sound to confirm that the seat and mirror positions have been saved 3 Repeat the procedure for a second driver using button 2 With an automatic transmission the vehicle must be in PARK P to recall the stored driving positions With a manual transmission and the engine is running the parking brake must be set to recall the memory seat driving positions The stored driving positions can be recalled without setting the parking brake if the vehicle is off Press one of the numbered memory buttons to recall the stored setting Each time a memory button is pressed a single beep will sound Three chimes sound and the setting is not recalled if you press button 1 or 2 when the vehicle is not in PARK P on an automatic transmission or the
362. p the sensing system distinguish between a moderate frontal impact and a more severe frontal impact For moderate frontal impacts dual stage airbags inflate at a level less than full deployment For more severe frontal impacts full deployment occurs Your vehicle also has a dual depth passenger airbag that adjusts the restraint according to crash severity seat location and safety belt status using electronic frontal sensors and other special sensors which enable the sensing system to monitor the position of the front passenger seat The passenger airbag inflates to a reduced depth when the passenger seat is ina forward position For more rearward front seating positions the passenger airbag may inflate to an increased depth a full deployment based on the crash severity measured early in the event Always wear your safety belt even with frontal airbags Your vehicle has seat position sensors which enables the sensing system to monitor the position of the driver s and right front passenger s seat Seat position sensors provide information that is used to determine if the airbags should deploy at a reduced level or at full deployment Your vehicle has seat mounted side impact and roof rail airbags See Airbag System on page 1 55 Seat mounted side impact and roof rail airbags are intended to inflate in moderate to severe side crashes In addition these roof rail airbags are intended to inflate in a severe frontal impact Seat m
363. page 5 57 eee Z CAUTION For any bulb changing procedure not listed in this section contact your dealer retailer A p Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb You or i others could be injured Be sure to read and Lighting follow the instructions on the bulb package High Intensity Discharge HID A CAUTION The low beam high intensity discharge lighting system operates at a very high voltage If you try to service any of the system components you could be seriously injured Have your dealer retailer or a qualified technician service them Your vehicle has HID headlamps After your vehicle s HID headlamp bulb has been replaced you may notice that the beam is a slightly different shade than it was originally This is normal Front Turn Signal and Fog Lamps To replace fog lamp bulb 13 2 Pull out the push pins located on the underside of the protection shield to remove the shield Reach up behind the front bumper area from under the vehicle to access the lamp housing Remove the bulb socket from the housing by turning the bulb socket one quarter turn counterclockwise Remove the electrical connector from the bulb by lifting the two plastic clips Pull the old bulb from the bulb socket keeping the bulb straight as you pull it out Install a new bulb Reverse the steps to reinstall the lamp assembly 5 56 N Dapy License Plate Lamp
364. pecifications 5 128 Service For service and parts needs visit your dealer retailer You will receive genuine GM parts and GM trained and supported service people Genuine GM parts have one of these marks ACVelco E parts GM aerial Goodwrench E Accessories Accessories and Modifications When non dealer non retailer accessories are added to your vehicle they can affect your vehicle s performance and safety including such things as airbags braking stability ride and handling emissions systems aerodynamics durability and electronic systems like antilock brakes traction control and stability control Some of these accessories could even cause malfunction or damage not covered by warranty GM Accessories are designed to complement and function with other systems on your vehicle Your GM dealer retailer can accessorize your vehicle using genuine GM Accessories When you go to your GM dealer retailer and ask for GM Accessories you will know that GM trained and supported service technicians will perform the work using genuine GM Accessories Also see Adding Equipment to Your Airbag Equipped Vehicle on page 1 69 California Proposition 65 Warning Most motor vehicles including this one contain and or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Engine exhaust many parts and systems including some inside the
365. perature settings Event Data Recorders This vehicle has an Event Data Recorder EDR The main purpose of an EDR is to record in certain crash or near crash like situations such as an airbag deployment or hitting a road obstacle data that will assist in understanding how a vehicle s systems performed The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time typically 30 seconds or less The EDR in this vehicle is designed to record such data as e How various systems in your vehicle were operating e Whether or not the driver and passenger safety belts were buckled fastened e How far if at all the driver was pressing the accelerator and or brake pedal e How fast the vehicle was traveling This data can help provide a better understanding of the circumstances in which crashes and injuries occur Important EDR data is recorded by your vehicle only if a non trivial crash situation occurs no data is recorded by the EDR under normal driving conditions and no personal data e g name gender age and crash location is recorded However other parties such as law enforcement could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation To read data recorded by an EDR special equipment is required and access to the vehicle or the EDR is needed In addition to the vehicle manufacturer other parties such as law
366. place Battery In Remote Key message displays in the DIC See Replace Battery In Remote Key under DIC Warnings and Messages on page 3 54 for additional information Notice When replacing the battery use care not to touch any of the circuitry Static from your body transferred to these surfaces may damage the transmitter To replace the battery in the RKE transmitter 1 Separate the halves of the transmitter with a flat thin object inserted into the notch located above the metal base 2 Remove the old battery Do not use a metal object 3 Insert the new battery positive side facing up Replace with a CR2032 or equivalent battery 4 Put the transmitter back together tightly Keyless Access System Operation Your vehicle may have a Keyless Access System that lets you lock and unlock your vehicle s doors open the trunk lid remotely start the engine and locate your vehicle or sound your vehicle s alarm from a distance as much as 195 feet 60 m away The Keyless Access System also lets you lock and unlock the vehicle s doors and access the trunk without removing the remote transmitter from your pocket purse briefcase etc The system operates when a front door handle is pulled or the remote trunk release button is pressed You must have the keyless access transmitter with you and within 3 feet 1 m of the door
367. polish is recommended for all bright metal parts Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent Wash the windshield thoroughly when cleaning the blades Bugs road grime sap anda buildup of vehicle wash wax treatments may cause wiper streaking Replace the wiper blades if they are worn or damaged Wipers can be damaged by e Extreme dusty conditions e Sand and salt e Heat and sun e Snow and ice without proper removal Aluminum or Chrome Plated Wheels and Trim Your vehicle may have either aluminum or chrome plated wheels Keep the wheels clean using a soft clean cloth with mild soap and water Rinse with clean water After rinsing thoroughly dry with a soft clean towel A wax may then be applied Notice Chrome wheels and other chrome trim may be damaged if you do not wash your vehicle after driving on roads that have been sprayed with magnesium calcium or sodium chloride These chlorides are used on roads for conditions such as ice and dust Always wash your vehicle s chrome with soap and water after exposure Notice If you use strong soaps chemicals abrasive polishes cleaners brushes or cleaners that contain acid on aluminum or chrome plated wheels you could damage the surface of the wheel s The repairs would not be covered by your warranty Use only
368. pressor 3 Be the eg ue ee i on a and unwrap tne sealanv air nose ose trom tne Kit to Temporarily Seal a Punctured Tire compressor Follow these directions closely for correct sealant usage The sealant air hose F is the top clear hose 4 Remove the valve stem cap from the flat tire by turning it counterclockwise 5 Attach the sealant filling hose F onto the tire valve stem Turn it clockwise until it is tight 6 Unwrap and plug the air compressor accessory plug E into an accessory power outlet in the vehicle See Accessory Power Outlet s on page 3 21 for more information Do not slam the door or close the window on the compressor accessory plug cord A CAUTION 1 Do a safety check before proceeding See fa Idling the engine in a closed in place or with Tire Goes Flat on page 5 83 the climate control system off can cause 2 Inspect the damaged tire deadly carbon monoxide CO See Engine The sealant cannot seal sidewall damage large Exhaust on page 2 47 punctures or a tire that has unseated from Hie WAGE See Aoaasige Service On page 7 6 7 Start the vehicle See Starting the Engine on Do not remove any objects that have penetrated page 2 34 for more information The vehicle must the tire be running while using the air compressor 5 87 A CAUTION Inflating something too much can make it explode and you or others could be injured Be sure to read the inflator instructions and
369. r let them know this and ask for instructions If the dealer retailer requests that you simply drop the vehicle off for service you are urged to do so as early in the work day as possible to allow for the same day repair Courtesy Transportation To enhance your ownership experience we and our participating dealers are proud to offer Courtesy Transportation a customer support program for vehicles with the Bumper to Bumper Base Warranty Coverage period in Canada and extended powertrain warranty in both the U S and Canada Several courtesy transportation options are available to assist in reducing your inconvenience when warranty repairs are required Courtesy Transportation is not a part of the New Vehicle Limited Warranty A separate booklet entitled Warranty and Owner Assistance Information furnished with each new vehicle provides detailed warranty coverage information Transportation Options Warranty service can generally be completed while you wait However if you are unable to wait GM helps to minimize your inconvenience by providing several transportation options Depending on the circumstances your dealer can offer you one of the following Shuttle Service Participating dealers can provide shuttle service to get you to your destination with minimal interruption of your daily schedule This includes one way or round trip shuttle service to a destination up to 10 miles 16 km from the dealership Pub
370. r information on the Engine Oil Life System and resetting the system 6 4 When the Change Engine Oil Soon message appears the following services checks and inspections are required Q Ooo Change engine oil and filter See Engine Oil on page 5 16 Reset oil life system See Engine Oil Life System on page 5 19 An Emission Control Service Visually check for any leaks or damage See footnote k Inspect engine air cleaner filter If necessary replace filter See Engine Air Cleaner Filter on page 5 21 See footnote I Rotate tires and check inflation pressures and wear See Tire Inspection and Rotation on page 5 75 and Tire Wear Inspection in At Least Once a Month on page 6 8 Inspect brake system See footnote a Check engine coolant and windshield washer fluid levels and add fluid as needed Perform any needed additional services See Additional Required Services in this section Inspect suspension and steering components See footnote b Inspect engine cooling system See footnote c Inspect wiper blades See footnote d Inspect restraint system components See footnote e Lubricate body components See footnote f Additional Required Services The following services should be performed at the first maintenance service after the indicated miles kilometers shown for each item Additional Required Services ee 25 000 50 000 75 000 100 000 125 000 150 000 Service an
371. r in acrash This system is designed to make installation of a child restraint easier The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system Make sure that a LATCH compatible child restraint is properly installed using the anchors or use the vehicle s safety belts to secure the restraint following the instructions that came with that restraint and also the instructions in this manual When installing a child restraint with a top tether you must also use either the lower anchors or the safety belts to properly secure the child restraint A child restraint must never be installed using only the top tether and anchor In order to use the LATCH system in your vehicle you need a child restraint that has LATCH attachments The child restraint manufacturer will provide you with instructions on how to use the child restraint and its attachments The following explains how to attach a child restraint with these attachments in your vehicle Not all vehicle seating positions or child restraints have lower anchors and attachments or top tether anchors and attachments Lower Anchors Lower anchors A are metal bars built into the vehicle There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments B 1 43 Top Tether Anchor A top tether A C anchors the top of the child restraint to the v
372. r vehicle If your vehicle has the keyless access system see Keyless Access System Operation on page 2 9 for instructions on matching a keyless access transmitter to your vehicle To match an RKE transmitter to your vehicle 1 Press the vehicle information button until Press V To Relearn Remote Key displays 2 Press the set reset button until Remote Key Learning Active is displayed 3 51 3 Press and hold the lock and unlock buttons on the first transmitter at the same time for about 15 seconds On vehicles with memory recall seats the first transmitter learned will match driver 1 and the second will match driver 2 A chime sounds indicating that the transmitter is matched 4 To match additional transmitters at this time repeat Step 3 Each vehicle can have a maximum of eight transmitters matched to it 5 To exit the programming mode you must cycle the key to LOCK OFF Blank Display This display shows no information DIC Compass Your vehicle may have a compass in the Driver Information Center DIC 3 52 Compass Zone The zone is set to zone eight upon leaving the factory Your dealer retailer will set the correct zone for your location Under certain circumstances such as during a long distance cross country trip or moving to a new state or province it will be necessary to compensate for compass variance by resetting the zone through the DIC if the zone is not set correctly Compass variance is
373. r wash To fold push the mirror toward the vehicle To return the mirror to its original position push outward Be sure to return both mirrors to their original unfolded position before driving If the vehicle has the memory package the mirrors can be programmed for personalization and curb view assist 2 49 Park Tilt Mirrors If the vehicle has the memory seat and mirrors the mirrors can be tilted to a preselected position when the vehicle is shifted into REVERSE R Use this park tilt feature to view the curb when parallel parking When the vehicle is shifted out of REVERSE R and after a five second delay the mirrors will return to their original position The park tilt can be turned on or off through the Driver Information Center DIC See DIC Vehicle Customization on page 3 68 for more information 2 50 Outside Convex Mirror A CAUTION A convex mirror can make things like other vehicles look farther away than they really are If you cut too sharply into the right lane you could hit a vehicle on your right Check your inside mirror or glance over your shoulder before changing lanes The passenger side mirror is convex A convex mirror s surface is curved so more can be seen from the driver s seat This mirror does not have a dimming feature Outside Heated Mirrors When the rear window defogger is turned on it also warms both outside rearview mirrors to help clear them of fog or ice See Rear
374. raction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance Warning The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law Warning The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure Wheel Alignment and Tire Balance
375. railer Tongue later in this section for more information Maximum trailer weight is calculated assuming only the driver is in the tow vehicle and it has all the required trailering equipment The weight of additional optional equipment passengers and cargo in the tow vehicle must be subtracted form the maximum trailer weight You can ask your dealer retailer for our trailering information or advice or you can write us at our Customer Assistance Offices See Customer Assistance Offices on page 7 5 for more information Weight of the Trailer Tongue The tongue load A of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle The Gross Vehicle Weight GVW includes the curb weight of the vehicle any cargo you may carry in it and the people who will be riding in the vehicle If you have a lot of options equipment passengers or cargo in your vehicle it will reduce the tongue weight your vehicle can carry which will also reduce the trailer weight your vehicle can tow And if you tow a trailer you must add the tongue load to the GVW because your vehicle will be carrying that weight too See Loading Your Vehicle on page 4 22 for more information about your vehicle s maximum load capacity If you are using a weight carrying hitch the trailer tongue A should weigh 10 to 15 percent of the total loaded trailer weight B After you have loaded your trailer weigh the tr
376. raint instructions are important so if they are not available obtain a replacement copy from the manufacturer Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle Be sure to properly secure any child restraint in your vehicle even when no child is in it Securing the Child Within the Child Restraint A CAUTION A child can be seriously injured or killed in a crash if the child is not properly secured in the child restraint Because there are different systems it is important to refer to the instructions that come with the restraint Make sure the child is properly secured following the instructions that came with that restraint 1 41 Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat We recommend that children and child restraints be secured in a rear seat including an infant or a child riding in a rear facing child restraint a child riding in a forward facing child seat an older child riding in a booster seat and children who are large enough using safety belts A label on your sun visor says Never put a rear facing child seat in the front This is because the risk to the rear facing child is so great if the airbag deploys A CAUTION A child in a rear facing child restraint can be seriously injured or killed if the right front pas
377. raised Do not allow passengers to remain in the vehicle To be even more certain the vehicle will not The following information tells you how to use the jack move you should put blocks at the front and and change a tire rear of the tire farthest away from the one being changed That would be the tire on the other side at the opposite end of the vehicle 5 103 Removing the Spare Tire and Tools The equipment you will need is in the trunk To gain access to the spare tire and jacking equipment do the following 1 Remove the spare tire cover 2 Remove the stow rod cap by pulling it straight up off of the rod 3 Turn the wing nut A on the compact spare tire B counterclockwise to remove it 4 Remove the spare tire and place it next to the flat tire 5 The tools you will be using next include the jack C wheel wrench D and extension E A Wing Nut D Wheel Wrench B Spare Tire E Extension C Jack F Strap 5 104 Removing the Flat Tire and Installing the Spare Tire 1 Do a safety check before proceeding See Changing a Flat Tire on page 5 102 for more information OA a 2 Loosen the wheel nuts but do not remove them yet using the wheel wrench Turn the handle about 180 degrees then return the handle back to the starting position This avoids taking the wrench off the lug nut for each turn 3 Find the jacking location using the diagram above and corresponding V shaped locat
378. re Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control e Press and hold the RES button on the steering wheel until the new desired speed is reached then release it e To increase vehicle speed in small increments press the RES button Each time this is done the vehicle goes about 1 mph 1 6 km h faster Reducing Speed While Using Cruise Control To reduce the vehicle s speed while using cruise control e Press and hold the SET button on the steering wheel until the desired lower speed is reached then release it e To slow down in very small amounts press the SET button on the steering wheel briefly Each time this is done the vehicle goes about 1 mph 1 6 km h slower Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle s speed When you take your foot off the pedal the vehicle will slow down to the previous set cruise speed 3 15 Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle s speed load and the steepness of the hills When going up steep hills you might have to step on the accelerator pedal to maintain the vehicle s speed When going downhill you might have to brake or shift to a lower gear to keep the vehicle s speed down When the brakes are applied the cruise control turns off Many drivers find this to be too much trouble and do not u
379. re With plain water or the wrong mixture your engine could get too hot but you would not get the overheat warning Your engine could catch fire and you or others could be burned Use a 50 50 mixture of clean drinkable water and DEX COOL coolant 5 28 Notice If you use an improper coolant mixture your engine could overheat and be badly damaged The repair cost would not be covered by your warranty Too much water in the mixture can freeze and crack the engine radiator heater core and other parts If you have to add coolant more than once or twice a year have your dealer retailer check your cooling system Notice If you use extra inhibitors and or additives in your vehicle s cooling system you could damage your vehicle Use only the proper mixture of the engine coolant listed in this manual for the cooling system See Recommended Fluids and Lubricants on page 6 11 for more information Checking Coolant FULL COLD The coolant surge tank and pressure cap are located on the driver s side of the vehicle toward the rear of the engine compartment See Engine Compartment Overview on page 5 14 for more information on location A CAUTION Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly Never turn the surge tank pressure cap even a little when the engine and radiator are hot The vehicle must be on a l
380. re information see Windshield Washer on page 3 11 3 25 Defogging and Defrosting Fog on the inside of windows is a result of high humidity moisture condensing on the cool window glass This can be minimized if the climate control system is used properly There are two modes to clear fog from the windshield Use the defog mode to clear the windows of fog or moisture and warm the passengers Use the defrost mode to remove fog or frost from the windshield more quickly T Mode Press the mode buttons until defog appears on the display Ni Defog This mode directs the air between the windshield floor outlets and side windows When this mode is selected the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is at or below freezing If recirculation mode is selected while in defog mode it will be cancelled after 10 minutes Ww Defrost Pressing defrost directs most of the air to the windshield with some air directed to the side windows In this mode the system automatically turns off recirculation and runs the air conditioning compressor unless the outside temperature is at or below freezing This mode may also cause the fan speed and air temperature to increase 3 26 Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window The rear window defogger will only work when the ignition is in ON RUN Gt Re
381. red 1 Before you start be sure you have enough room around the vehicle It should be parked on a level surface 2 Firmly apply the parking brake See Parking Brake on page 2 43 Be ready to apply the regular brake immediately if the vehicle begins to move 3 With the engine off turn the ignition to ON RUN but do not start the engine Without applying the regular brake try to move the shift lever out of PARK P with normal effort If the shift lever moves out of PARK P contact your dealer retailer for service Ignition Transmission Lock Check While parked and with the parking brake set try to turn the ignition to LOCK OFF in each shift lever position e With an automatic transmission the ignition should turn to LOCK OFF only when the shift lever is in PARK P e With the key access ignition system the ignition key should come out only in LOCK OFF With keyless access ignition the ignition key does not come out See Ignition Positions Key Access on page 2 31 or Ignition Positions Keyless Access on page 2 33 Contact your dealer retailer if service is required Parking Brake and Automatic Transmission Park P Mechanism Check A CAUTION When you are doing this check your vehicle could begin to move You or others could be injured and property could be damaged CAUTION Continued CAUTION Continued Make sure there is room in front of your vehicle in case it begins to roll Be ready
382. remaining doors will unlock The interior lamps will come on and stay on for 20 seconds or until the ignition is turned on If enabled through the DIC the parking lamps will flash twice to indicate unlocking has occurred See DIC Vehicle Customization on page 3 68 s Remote Trunk Release Press and hold eh for about one second to release the trunk lid The transmission must be in PARK P for this feature to operate 2 Vehicle Locator Panic Alarm Press and release 2 to locate your vehicle The turn signal lamps will flash and the horn will sound three times Press and hold 2 for more than two seconds to activate the panic alarm The turn signal lamps will flash and the horn will sound repeatedly for 30 seconds The alarm will turn off when the ignition is moved to START or amp is pressed again The ignition must be in LOCK OFF for the panic alarm to work Matching Transmitter s to Your Vehicle Each RKE transmitter is coded to prevent another transmitter from unlocking your vehicle If a transmitter is lost or stolen a replacement can be purchased through your dealer retailer All transmitters need to be re coded to match the new transmitter The lost transmitter will no longer work after the new transmitters are re coded The vehicle can have a maximum of eight transmitters matched to it See Relearn Remote Key under DIC Operation and Displays on page 3 48 Battery Replacement Replace the battery if the Re
383. res you could be burned Do not drive with it off and be careful working on the engine with the air cleaner filter off Notice If the air cleaner filter is off a backfire can cause a damaging engine fire And dirt can easily get into your engine which will damage it Always have the air cleaner filter in place when you are driving Automatic Transmission Fluid How to Check Automatic Transmission Fluid It is not necessary to check the transmission fluid level A transmission fluid leak is the only reason for fluid loss If a leak occurs take the vehicle to the dealer retailer service department and have it repaired as soon as possible There is a special procedure for checking and changing the transmission fluid Because this procedure is difficult you should have this done at the dealer retailer service department Contact your dealer retailer for additional information or the procedure can be found in the service manual To purchase a service manual see Service Publications Ordering Information on page 7 15 Notice Use of the incorrect automatic transmission fluid may damage your vehicle and the damages may not be covered by your warranty Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 6 11 Change the fluid and filter at the intervals listed in Additional Required Services on page 6 5 and be sure to use the fluid listed in Recommended Fluids and Lubricants on p
384. res and mirror adjustment If the trailer has electric brakes start your vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working This lets you check your electrical connection at the same time During your trip check occasionally to be sure that the load is secure and that the lamps and any trailer brakes are still working Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer This can help you avoid situations that require heavy braking and sudden turns Passing You will need more passing distance up ahead when you are towing a trailer And because the vehicle is a good deal longer you will need to go much farther beyond the passed vehicle before you can return to your lane Backing Up Hold the bottom of the steering wheel with one hand Then to move the trailer to the left just move that hand to the left To move the trailer to the right move your hand to the right Always back up slowly and if possible have someone guide you Making Turns Notice Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle Your vehicle could be damaged Avoid making very sharp turns while trailering When you are turning with a trailer make wider turns than normal Do this so your trailer will not strike soft shoulders curbs road signs trees or other obj
385. resulting in serious injury or even death in a crash To help make sure your restraint systems are working properly after a crash have them inspected and any necessary replacements made as soon as possible If you have had a crash do you need new belts or LATCH system if equipped parts After a very minor crash nothing may be necessary But the belt assemblies that were used during any crash may have been stressed or damaged See your dealer retailer to have your safety belt assemblies inspected or replaced If your vehicle has the LATCH system and it was being used during a crash you may need new LATCH system parts New parts and repairs may be necessary even if the belt or LATCH system if equipped was not being used at the time of the crash If an airbag inflates you will need to replace airbag system parts See the part on the airbag system earlier in this section Have your safety belt pretensioners checked if your vehicle has been in a crash if your airbag readiness light stays on after you start your vehicle or while you are driving See Airbag Readiness Light on page 3 33 1 71 4 NOTES 1 72 Section 2 Features and Controls KR6Y Si aaeeea a aa 2 3 Starting and Operating Your Vehicle 2 31 Remote Keyless Entry RKE System 2 5 New Vehicle Break In cseeeeeeeeeeeeeeeeee 2 31 Keyless Access System c eeeeeeeeeneee een eeee es 2 6 Ignition Position
386. rivers are encouraged to set up their radio station favorites while the vehicle is stopped Tune to your favorite stations using the presets favorites button and steering wheel controls if the vehicle has this feature See Defensive Driving on page 4 2 3 83 FAV Favorites A maximum of 36 stations can be programmed as favorites using the six pushbuttons positioned below the radio station frequency labels on the display and by using the radio favorites page button FAV button Press the FAV button to go through up to six pages of favorites each having six favorite stations available per page Each page of favorites can contain any combination of AM FM or XM if equipped stations To store a station as a favorite perform the following steps 1 Tune to the desired radio station 2 Press the FAV button to display the page where the station is to be stored 3 Press and hold one of the six pushbuttons until a beep sounds When that pushbutton is pressed and released the radio recalls the station that was set 4 Repeat the steps for each pushbutton radio station to be stored as a favorite The number of favorites pages can be setup using the CONFIG button To setup the number of favorites pages perform the following steps 1 Press the CONFIG button to display the radio setup menu 2 Press the pushbutton located below the FAV label 3 84 3 Select the desired number of favorites pages by pressing the pushbutt
387. rom where it was stopped Press the pushbutton located under the Hl label again while in DVDPreStop DVDStop displays Press gt IIl while in DVDStop to begin playback from the beginning of the DVD audio disc Press gt H during DVD audio playback to pause or resume playback Finding Songs on DVD Audio TUNE TONE Turn this knob to display a list of all tracks in all groups on the DVD audio disc Stop turning this knob or press the TUNE TONE knob to start playback of a particular track Ki SEEK D Press the left arrow to go to the start of the current track if more than five seconds have played Press the right arrow to go to the next track If either arrow is held or pressed multiple times the player continues moving backward or forward through the tracks within the current Group MENU SELECT To change Groups press the pushbutton located under the Menu label to display a list of all Groups Turn the MENU SELECT knob to highlight the desired Group Press the MENU SELECT knob to select it Playback begins from track 1 of the selected Group 3 89 Shuffle on DVD Audio Press the pushbutton located under the Shuffle label to begin random playback of all songs in the current Group Press again to turn off random playback Selecting DVD Audio Streams Each DVD audio Group may contain audio content that is encoded in one or two formats For example a particular Group may have both a 5 1 surround audio stream
388. roperly Safety Belt Extender If the vehicle s safety belt will fasten around you you should use it But if a safety belt is not long enough your dealer retailer will order you an extender When you go in to order it take the heaviest coat you will wear so the extender will be long enough for you To help avoid personal injury do not let someone else use it and use it only for the seat it is made to fit The extender has been designed for adults Never use it for securing child seats To wear it attach it to the regular safety belt For more information see the instruction sheet that comes with the extender 1 31 Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle s safety belts 1 32 The manufacturer s instructions that come with the booster seat state the weight and height limitations for that booster Use a booster seat with a lap shoulder belt until the child passes the below fit test e Sit all the way back on the seat Do the knees bend at the seat edge If yes continue If no return to the booster seat Buckle the lap shoulder belt Does the shoulder belt rest on the shoulder If yes continue If no try using the rear safety belt comfort guide See Rear Safety Belt Comfort Guides under Lap Shoulder Belt on page 1 25 for more information If the shoulder belt still does not rest on the shoulder then return to the booster seat e Does
389. rrent System on page 2 27 for more information Tighten Gas Cap This message displays when the fuel cap has not been fully tightened Recheck the fuel cap to ensure that it is on and tightened properly Tire Learning Active This message displays when the Tire Pressure Monitor System TPMS is re learning the tire positions on your vehicle The tire positions must be re learned after rotating the tires or after replacing a tire or sensor See Tire Inspection and Rotation on page 5 75 Tire Pressure Monitor System on page 5 70 and Inflation Tire Pressure on page 5 67 for more information Transmission Hot Idle Engine This message displays when the transmission fluid in your vehicle is too hot Stop the vehicle and allow it to idle until the transmission cools down or until this message is removed Trunk Open This message displays when the trunk is not closed completely Make sure that the trunk is closed completely Turn Signal On This message displays as a reminder to turn off the turn signal if you drive your vehicle for more than about 1 mile 1 6 km with a turn signal on A multiple chime sounds when this message displays Washer Fluid Low Add Fluid This message displays when your vehicle is low on windshield washer fluid Refill the windshield washer fluid reservoir as soon as possible See Windshield Washer Fluid on page 5 39 for more information 3 67 DIC Vehicle Customization Your vehicle has cus
390. rs on page 1 6 for more information Q Remote Start If your vehicle has this feature press Q after pressing to operate the remote start feature See Remote Vehicle Start on page 2 14 for additional information ef Trunk Press and hold fai for about one second to open the trunk while the engine is turned off or the shift lever is in PARK P 2 Vehicle Locator Panic Alarm Press and release 2 to locate your vehicle The horn will chirp three times and the turn signal lamps will flash three times Press and hold 4 for three seconds to sound the panic alarm The horn will chirp and the turn signal lamps will flash for 30 seconds Press and release 2 again to cancel the panic alarm Matching Transmitter s to Your Vehicle Each Keyless Access System is coded to allow only transmitters programmed to your vehicle to work If a transmitter is lost or stolen a replacement can be purchased and programmed through your dealer retailer Your dealer retailer can reprogram your vehicle so lost or stolen transmitters no longer work with your vehicle Each vehicle can have a maximum of four transmitters matched to it To match a new transmitter to your vehicle when you have a recognized transmitter do the following Two recognized transmitters are required for Canadian owners 1 The vehicle must be off 2 Have the recognized transmitter and the new unrecognized transmitter s with you 3 Insert the vehicle key in
391. rument panel or the safety belts With safety belts you slow down as the vehicle does You get more time to stop You stop over more distance and your strongest bones take the forces That is why safety belts make such good sense Questions and Answers About Safety Belts Q A pr Will be trapped in the vehicle after a crash if I am wearing a safety belt You could be whether you are wearing a safety belt or not But your chance of being conscious during and after an accident so you can unbuckle and get out is much greater if you are belted And you can unbuckle a safety belt even if you are upside down If my vehicle has airbags why should I have to wear Safety belts Airbags are supplemental systems only so they work with safety belts not instead of them Whether or not an airbag is provided all occupants still have to buckle up to get the most protection That is true not only in frontal collisions but especially in side and other collisions Q If am a good driver and I never drive far from A home why should wear safety belts You may be an excellent driver but if you are ina crash even one that is not your fault you and your passenger s can be hurt Being a good driver does not protect you from things beyond your control such as bad drivers Most accidents occur within 25 miles 40 km of home And the greatest number of serious injuries and deaths occur at speeds
392. s Technical Service Bulletins and Manuals are available for current and past model GM vehicles To request an order form specify year and model name of the vehicle ORDER TOLL FREE 1 800 551 4123 Monday Friday 8 00 AM 6 00 PM Eastern Time For Credit Card Orders Only VISA MasterCard Discover visit Helm Inc on the World Wide Web at www helminc com Or you can write to Helm Incorporated P O Box 07130 Detroit MI 48207 Prices are subject to change without notice and without incurring obligation Allow ample time for delivery Note to Canadian Customers All listed prices are quoted in U S funds Canadian residents are to make checks payable in U S funds Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle s performance and how it is driven For example your vehicle uses computer modules to monitor and control engine and transmission performance to monitor the conditions for airbag deployment and deploy airbags in a crash and if so equipped to provide antilock braking to help the driver control the vehicle These modules may store data to help your dealer retailer technician service your vehicle Some modules may also store data about how you operate the vehicle such as rate of fuel consumption or average speed These modules may also retain the owner s personal preferences such as radio pre sets seat positions and tem
393. s The disc can be removed If the disc is not removed after several seconds the disc automatically pulls back into the player and begins playing For the Six Disc CD player press and hold for two seconds to eject all discs Ki SEEK Press the left arrow to go to the start of the current track if more than five seconds have played Press the right arrow to go to the next track If either arrow is held or pressed multiple times the player continues moving backward or forward through the tracks on the CD lt lt REV Fast Reverse Press and hold to reverse playback quickly within a track Sound is heard at a reduced volume and the elapsed time of the track displays Release to resume playing the track gt gt FWD Fast Forward Press and hold to advance playback quickly within a track Sound is heard at a reduced volume and the elapsed time of the track displays Release to resume playing the track 3 88 FM AM Press to listen to the radio when a CD is playing The CD remains inside the radio for future listening CD Press to play a CD when listening to the radio The disc and or track number displays when a CD is in the player AUX Auxiliary Press to automatically search for an auxiliary input device such as a portable audio player If a portable audio player is not connected No Aux Input Device Found displays Playing a DVD A Audio Disc The radio with DVD Audio HDD and USB is capable of play
394. s Key Access eeeee 2 31 Remote Keyless Entry RKE System Ignition Positions Keyless Access 2 33 OperatiONn eeii otis eevite aie 2 7 Retained Accessory Power RAP ccecce 2 34 Keyless Access System Operation 005 2 9 Starting the Engine ceeeeeeeeeneeeeeeeeeenee 2 34 Remote Vehicle Start c cceeeeeeeeeeeeeee ees 2 14 Engine Coolant Heater cceeeeeeneeeeeeeees 2 36 Doors and LOCKS vc sascsersiiapassicraccsaxetnccanncorks 2 17 Automatic Transmission Operation 2 37 Door LOCKS iaer rnea eaea ee 2 17 Manual Transmission Operation s s s1 2 41 Central Door Unlocking System 0 c cceeeeeee 2 17 Parking Brake eccccieesie ieee fp eeieeeeteeeereees 2 43 Power Door LOCKS 0ccccceeeeeeeeeeeeeeeeeaeees 2 18 Shifting Into PARK P Automatic Delayed Locking ccccccseeseeseeteseeetsessenee 2 18 TransMisSiOn seeseeeeese ieee etree 2 44 Programmable Automatic Door Locks 2 18 Shifting Out of PARK Phasis ag ste tteeeeee 2 45 Rear Door Security Locks 2 0 c 0eeeeeee es 2 19 Parking Your Vehicle Manual Transmission 2 46 Lockout Protection csces ceeendscaisateds oidoeisaces 2 20 Parking Over Things That Burn 00 2 47 MND saaan e EA ea naacectanate sioncedaeateanertel 2 20 Engine Exhaust 1 0 0 2 47 WiINdOWS 22 ccsecehccseceediteeeiatisyeten tutes ees 2 23 Pun
395. s are located under the root folder The next and previous folder functions do not display on a CD that was recorded without folders or playlists The radio displays F1 DISC for the root directory When the CD contains only playlists and compressed audio files but no folders all files are located under the root folder The folder down and the folder up buttons search playlists Px first and then goes to the root folder The radio displays F1 DISC for the root directory Order of Play Tracks recorded to the CD R or CD RW play in the following order e Play begins from the first track in the first folder and continues sequentially through all tracks in each folder When the last track of the last folder has played play continues from the first track of the first playlist Playlists can be changed by pressing the next and previous folder button e Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist When the last track of the last playlist has played play continues from the first track of the first folder When play enters a new folder the display does not automatically show the new folder name unless the folder mode has been chosen as the default display The new track name displays File System and Naming The song name displays the song name that is contained in the ID3 tag If the song name is not in the ID3 tag the radio displays the file name withou
396. s safe to do so If underinflated inflate to the proper pressure See Tires on page 5 59 for more information 3 40 When the Light Flashes First and Then is Solid This indicates that there may be a problem with the Tire Pressure Monitor System The light flashes for about a minute and stays on solid for the remainder of the ignition cycle This sequence will repeat with every ignition cycle See Tire Pressure Monitor System on page 5 70 for more information Malfunction Indicator Lamp Check Engine Light A computer system called OBD II On Board Diagnostics Second Generation monitors operation of the fuel ignition and emission control systems It makes sure that emissions are at acceptable levels for the life of the vehicle helping to produce a cleaner environment The check engine light comes on to indicate that there is an OBD II problem and service is required Malfunctions often are indicated by the system before any problem is apparent This can prevent more serious damage to your vehicle This system is also designed to assist your service technician in correctly diagnosing any malfunction Notice f you keep driving your vehicle with this light on after a while the emission controls might not work as well your vehicle s fuel economy might not be as good and the engine might not run as smoothly This could lead to costly repairs that might not be covered by your warranty Notice Modifications mad
397. s feature allows you to select the language in which the DIC messages will appear Press the customization button until the Display Language screen appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings English default All messages will appear in English Deutsch All messages will appear in German Italiano All messages will appear in Italian Francais All messages will appear in French Espanol All messages will appear in Spanish Portugese All messages will appear in Portugese Arabic All messages will appear in Arabic Chinese All messages will appear in Chinese Japanese All messages will appear in Japanese No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Auto Door Lock This feature allows you to select when the vehicle s doors will automatically lock See Programmable Automatic Door Locks on page 2 18 for more information Press the customization button until Auto Door Lock appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Shift Out Of Park default on Automatic Transmission Automatic Transmission Only The vehicle s doors a
398. s in the proper sequence to torque specifications in Capacities and Specifications on page 5 128 Brake linings should always be replaced as complete axle sets Brake Pedal Travel See your dealer retailer if the brake pedal does not return to normal height or if there is a rapid increase in pedal travel This could be a sign that brake service might be required Brake Adjustment Every time you apply the brakes with or without the vehicle moving the brakes adjust for wear Replacing Brake System Parts The braking system on a vehicle is complex Its many parts have to be of top quality and work well together if the vehicle is to have really good braking Your vehicle was designed and tested with top quality brake parts When you replace parts of the braking system for example when the brake linings wear down and you need new ones put in be sure you get new approved replacement parts If you do not the brakes might not work properly For example if someone puts in brake linings that are wrong for your vehicle the balance between the front and rear brakes can change for the worse The braking performance you have come to expect can change in many other ways if someone puts in the wrong replacement brake parts Battery Your vehicle has a maintenance free battery It is located in the trunk behind the trim panel on the passenger side of the vehicle When it is time for a new battery see your dealer retailer for
399. s offer the best protection for adults but not for young children and infants Neither the vehicle s safety belt system nor its airbag system is A CAUTION Airbags inflate with great force faster than the blink of an eye Anyone who is up against or very close to any airbag when it inflates can be seriously injured or killed Do not sit unnecessarily close to the airbag as you would be if you were sitting on the edge of your seat or designed for them Young children and infants need the protection that a child restraint system can provide Always secure children properly in your vehicle To read how see Older Children on page 1 32 or Infants and Young Children on page 1 35 leaning forward Safety belts help keep you in position before and during a crash Always wear your safety belt even with airbags The driver should sit as far back as possible while still maintaining control of the vehicle Occupants should not lean on or sleep against the door or side windows in seating positions with seat mounted side impact airbags and or There is an airbag readiness light on the ee e instrument panel cluster roof rail airbags A which shows the airbag FN symbol The system checks the airbag electrical system for malfunctions The light tells you if there is an electrical problem See Airbag Readiness Light on page 3 33 for more information 1 57 Where Are the Airbags The right front passenger s frontal a
400. sappears when the process has ended The recorded songs are now available Copy Protected CD s Make sure the disc is not copy protected The radio does not copy a copy protected CD to the HDD 3 92 Stopping the Recording While recording from the audio CD press the REC button to display the stop recording option Press the pushbutton located under this option to confirm the selection Ejecting a CD or Turning Off Your Vehicle While Recording If the CD is ejected or the vehicle is turned off before the recording process has completed tracks that have been completely recorded are stored to the HDD Incomplete tracks are discarded Re recording Audio CDs If a CD has already been recorded the radio system will not record the contents again If a partially recorded CD is selected for recording only those songs which are not already on the HDD will be recorded Audio CD Song Artist Album and Genre Information Radios with HDD contain a Gracenote Database that the radio uses to determine the song artist aloum and genre information The Gracenote Database allows the radio to record an audio CD to the HDD and store the content using song artist album and genre information Newly released audio CDs as well as some less common audio CDs may not be found in the Gracenote Database stored on the HDD If these audio CDs contain CD text the radio will use the CD text information when recording the content to the HDD
401. se Plate Lamps c eeeeeeeeeeeeeeeeeees 5 56 Light Airbag Readiness cceeeeeeeeeeeeeeneeeen eres 3 33 Antilock Brake System Warning ccce 3 38 Brake System Warning c cceceeeeeeeeeeee ees 3 37 Charging Systemi ai ccccucwctepedemectetennseeweneyenntes 3 36 Cruise Control neersien nie 3 46 Engine Coolant Temperature Warning 3 39 Foglamp senene ann NE 3 45 Highbeam ODS arisi mansnren rgan aae eeii 3 46 Lights On Reminder scssereneeeenrrerrnrrerenens 3 46 Malfunction Indicator seirresnseisa nenie 3 40 Oil Pressure 0 cece eee ee cece eee eee eee eee een eee eeaes 3 43 Passenger Airbag Status Indicator 3 34 Safety Belt Reminders cceseeeeeeeeeeees 3 32 SI A E E 3 45 Tire Press re eiropas in e o a aA 3 40 Traction Control System TCS StabiliTrak 3 38 Up SHIT wcidanahie sccesedetace ant taamaidyas west aa 3 36 Lighting ENUY eienn epa a E dese 3 19 Parade DIMMING sirsie 3 19 EONS e E 3 16 Fl shto Pass uerrini naen 3 9 High Low Beam Changer s esseeresserrerrerrenne 3 8 On Reminder c cceeeeeeeceeeeeeeeea eee eeaeeaes 3 17 Limited Slip Rear Axle i e 4 8 Loading Your Vehicle 0 ce ceeeeeeeeeeeeeeeeees 4 22 Lockout Protection cc cccise cea cenciwctdenese cater een eaten 2 20 Locks Central Door Unlocking System 00 2 17 Delayed Locking 0 0ccseeeeeeeeeeeeeeeseeneeees 2 18 OOK meses e ma
402. se cruise control on steep hills Ending Cruise Control There are three ways to end cruise control e Step lightly on the brake pedal manual and automatic transmissions e Press the clutch pedal to the floor manual transmissions e Press the cancel button on the steering wheel e Press the On Off button on the steering wheel Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off Headlamps The exterior lamp control is located towards the end of the turn signal multifunction lever Exterior Lamp Control Turn the band with this symbol on it to operate the exterior lamps The exterior lamp control has four positions D Off This position turns off all lamps except the Daytime Running Lamps DRL AUTO Automatic This position puts the headlamps in automatic mode AUTO mode turns the exterior lamps on and off depending upon how much light is available outside of the vehicle 300 Parking Lamps This position turns on the parking lamps together with the following e Sidemarker Lamps e Taillamps e License Plate Lamps e Instrument Panel Lights AD Headlamps This position turns on the headlamps together with the previously listed lamps and lights Wiper Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers have been in use for about six seconds For this feature to work the e
403. se this band to set the length of the delay between wipes when using the delay feature The closer the band is moved towards w S the longer the delay The windshield wiper lever must be in delay for this feature to work 1 Low Speed Move the lever to this position for slow steady wiping cycles 2 High Speed Move the lever to this position for rapid wiping cycles If the windshield wipers are in use for about six seconds while you are driving the exterior lamps come on automatically if the exterior lamp control is in AUTO See Wiper Activated Headlamps on page 3 17 for more information Be sure to clear ice and snow from the wiper blades before using them If they are frozen to the windshield gently loosen or thaw them If the blades do become damaged install new blades For more information see Windshield Wiper Blade Replacement on page 5 57 Heavy snow or ice can overload the wiper motor A circuit breaker will stop the motor until it cools down Clear away snow or ice to prevent an overload Rainsense Wipers Vehicles with Rainsense windshield wipers have a moisture sensor for this feature mounted on the interior side of the windshield behind the rearview mirror This sensor automatically operates the wipers by monitoring the amount of moisture build up on the windshield Wipes occur as needed to clear the windshield depending on driving conditions and the sensitivity setting In light rain or snow fewer wipes
404. security light to go out 4 Then reach in through the window unlock the door with the manual door lock and open the door This should set off the alarm While the alarm is set the power door unlock switch will not work If the alarm does not sound when it should but the headlamps flash check to see if the horn works The horn fuse may be blown To replace the fuse see Fuses and Circuit Breakers on page 5 122 Fuses and Circuit Breakers If the alarm does not sound or the headlamps do not flash the vehicle should be serviced by your dealer retailer 2 28 Immobilizer This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference received including interference that may cause undesired operation of the device Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment Immobilizer Operation Key Access Your vehicle has a passive theft deterrent system The system is automatically armed when the key is removed from the ignition The theft deterrent
405. senger s airbag inflates This is because the back of the rear facing child restraint would be very close to the inflating airbag Even though the passenger sensing system is designed to turn off the right front passenger s frontal airbag if the system detects a CAUTION Continued 1 42 CAUTION Continued rear facing child restraint no system is fail safe and no one can guarantee that an airbag will not deploy under some unusual circumstance even though it is turned off We recommend that rear facing child restraints be secured in a rear seat even if the airbag is off If you secure a forward facing child restraint in the right front seat always move the front passenger seat as far back as it will go It is better to secure the child restraint in a rear seat See Passenger Sensing System on page 1 64 for additional information When securing a child restraint in a rear seating position study the instructions that came with your child restraint to make sure it is compatible with this vehicle Wherever you install a child restraint be sure to secure the child restraint properly Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle Be sure to properly secure any child restraint in your vehicle even when no child is in it Lower Anchors and Tethers for Children LATCH The LATCH system holds a child restraint during driving o
406. sing system may not operate properly if the original seat trim is replaced with non GM covers upholstery or trim or with GM covers upholstery or trim designed for a different vehicle Any object such as an aftermarket seat heater or a comfort enhancing pad or device installed under or on top of the iad seat fabric could also interfere with the operation of the passenger sensing system This could either prevent proper deployment of the passenger airbag s or prevent the passenger sensing system from properly turning off the passenger airbag s See Passenger Sensing System on page 1 64 If you have any questions about this you should contact Customer Assistance before you modify your vehicle The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual See Customer Satisfaction Procedure on page 7 2 Because have a disability have to get my vehicle modified How can find out whether this will affect my airbag system If you have questions call Customer Assistance The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual See Customer Satisfaction Procedure on page 7 2 In addition your dealer retailer and the service manual have information about the location of the airbag sensors sensing and diagnostic module and airbag wiring 1 69 Restraint System Check Checking the
407. sing the Remote Keyless Entry RKE or keyless access transmitter See Remote Vehicle Start on page 2 14 for more information Press the customization button until Remote Start appears in the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off The remote start feature will be disabled On default The remote start feature will be enabled No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Advanced Features Exit This feature allows you to exit the advanced features menu Press the customization button until Advanced Features Press V To Exit appears in the DIC display Press the set reset button once to exit the menu Feature Settings Press V To Exit will appear Press the set reset button to exit the menu If you do not exit pressing the customization button again will return you to the beginning of the menu Exiting the Feature Settings Advanced Features Menu The feature settings advanced features menus will be exited when any of the following occurs e The vehicle is no longer in ON RUN e The trip fuel or vehicle information DIC buttons are pressed e The end of the feature settings menu is reached and exited A 40 second time period has elapsed with no selection
408. sit www gracenote com CD and music related data from Gracenote Inc copyright 2000 2007 Gracenote Gracenote Software copyright 2000 2007 Gracenote This product and service may practice one or more of the following U S Patents 5 987 525 6 061 680 6 154 773 6 161 132 6 230 192 6 230 207 6 240 459 6 330 593 and other patents issued or pending Some services supplied under license from Open Globe Inc for U S Patent 6 304 523 Gracenote and CDDB are registered trademarks of Gracenote The Gracenote logo and logotype and the Powered by Gracenote logo are trademarks of Gracenote If you require more information regarding the use of the Gracenote Service visit www gracenote com corporate For the data provided by Gracenote Music Recognition Service the content is not necessarily guaranteed 100 Regarding the use of Gracenote Music Recognition Service When this product is used it is necessary to agree to the following articles 3 93 This application or device contains software from Gracenote Inc of Emeryville California Gracenote The software from Gracenote the Gracenote Software enables this application to perform disc and or file identification and obtain music related information including name artist track and title information Gracenote Data from online servers or embedded databases collectively Gracenote Servers and to perform other functions
409. solines that are not reformulated for low emissions can contain an octane enhancing additive called methylcyclopentadieny manganese tricarbonyl MMT ask the attendant where you buy gasoline whether the fuel contains MMT We recommend against the use of such gasolines Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system could be affected The malfunction indicator lamp might turn on If this occurs return to your dealer retailer for service Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada the proper fuel might be hard to find Never use leaded gasoline or any other fuel not recommended in the previous text on fuel Costly repairs caused by use of improper fuel would not be covered by your warranty To check the fuel availability ask an auto club or contact a major oil company that does business in the country where you will be driving Filling the Tank A CAUTION Fuel vapor burns violently and a fuel fire can cause bad injuries To help avoid injuries to you and others read and follow all the instructions on the pump island Turn off your engine when you are refueling Do not smoke if you are near fuel or refueling your vehicle Do not use cellular phones Keep sparks flames and smoking materials away from fuel Do not leave the fuel pump unattended when refueling your vehicle This is against the law in some pl
410. songs from the disc Press the pushbutton located under the desired record option A status bar appears on the top of the display when the recording process starts The status bar disappears when the process has ended The recorded songs are now available AAC and OGG Vorbis file types are not fully supported These file types may or may not play and may be shown without Tag information Without Tag information available these file types may be identified only by filename Audiobooks from www audible com can also be transferred to the HDD using the record function See Audiobooks later in this section for more information USB Host Support The USB connector uses the USB standards 1 1 and 2 0 This type of connector supports rates for low speed 1 5 Mb s full speed 12 Mb s and high speed 480 Mb s USB Supported Devices e USB Flash Drives e Portable USB Hard Drives Playing From the Hard Disc Drive HDD Hard Disc Drive Press the HDD button to start the HDD mode HDD displays and playback resumes from where it was last stopped 3 95 HDD Playback Mode HDD Menu This radio system displays the current hard drive 1 Press the MENU SELECT knob to display the playback mode See the following table showing the HDD Menu display mode options and what happens as the mode is 2 Turn this knob to highlight an option from the HDD displayed Menu The available options are Mode When Displayed enue ones System is randoml
411. spect power steering lines and hoses for proper hook up binding leaks cracks chafing etc 6 6 c Visually inspect hoses and have them replaced if they are cracked swollen or deteriorated Inspect all pipes fittings and clamps replace with genuine parts as needed To help ensure proper operation a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year d Inspect wiper blades for wear cracking or contamination Clean the windshield and wiper blades if contaminated Replace wiper blades that are worn or damaged See Windshield Wiper Blade Replacement on page 5 57 and Windshield and Wiper Blades on page 5 117 for more information e Make sure the safety belt reminder light and safety belt assemblies are working properly Look for any other loose or damaged safety belt system parts If you see anything that might keep a safety belt system from doing its job have it repaired Have any torn or frayed safety belts replaced Also see Checking the Restraint Systems on page 1 70 f Lubricate all key lock cylinders Lubricate all body door hinges Lubricate all hinges and latches including those for the hood rear compartment console door and any folding seat hardware More frequent lubrication may be required when exposed to a corrosive environment Applying silicone grease on weatherstrips with a clean cloth will mak
412. splays See Vehicle Information Display Menu Items following for more information on these displays Customization Press this button to scroll through each of the customization features See DIC Vehicle Customization on page 3 68 for more information on the customization features 3 48 V Set Reset Press this button to reset certain DIC features and to acknowledge DIC warning messages and clear them from the DIC display A V Menu Up Down Press this button to scroll up and down the menu items Trip Fuel Display Menu Items ZN Trip Fuel The following display menu items can be displayed by pressing the trip fuel button Odometer This display shows the distance the vehicle has been driven in either miles mi or kilometers km Trip A or Trip B These displays show the current distance traveled since the last reset for each trip odometer in either miles mi or kilometers km Both odometers can be used at the same time Each trip odometer can be reset to zero separately by pressing and holding the set reset button for a few seconds while the desired trip odometer is displayed Fuel Range This display shows the approximate number of remaining miles mi or kilometers km you can drive without refilling the fuel tank This estimate is based on the current driving conditions and changes if the driving conditions change For example if you are driving in traffic and making frequent stops the display may re
413. ss transmitter in the Leaving children in a vehicle with the ignition vehicle and they could be seriously injured or key is dangerous for many reasons children or killed if caught in the path of a closing others could be badly injured or even killed window Do not leave the keyless access They could operate the power windows or other transmitter in a vehicle with children controls or even make the vehicle move The windows will function with the keys in the ignition and they could be seriously injured or killed if caught in the path of a closing window Do not leave the keys in a vehicle with children A CAUTION Leaving children in a vehicle with the keyless access transmitter is dangerous for many reasons children or others could be badly injured or even killed They could operate the power windows or other controls or even make CAUTION Continued You will have either of the following keys This key can be used for the driver s door ignition and glove box This key located inside the keyless access transmitter can be used for the driver s door glove box and rear seat pass through door See Rear Seat Pass Through Door under Trunk on page 2 20 for more information To remove the key press the button A near the bottom of the keyless access transmitter and pull the key out Never pull the key out without pressing the button Your vehicle may have the Keyless Access System Se
414. start your vehicle if the battery is allowed to drain for an extended period of time D START This position starts the engine 2 33 Retained Accessory Power RAP These vehicle accessories can be used for up to 10 minutes after the engine is turned off e Audio System e Power Windows e Sunroof Power to the audio system will work up to 10 minutes or until the driver s door is opened Power to the windows or sunroof will work up to 10 minutes or until any door is opened For an additional 10 minutes of operation close all the doors and turn the key to ON RUN and then back to LOCK OFF Starting the Engine Place the transmission in the proper gear Automatic Transmission Move the shift lever to PARK P or NEUTRAL N The engine will not start in any other position this is a safety feature To restart when you are already moving use NEUTRAL N only 2 34 If your vehicle has the keyless access system put your foot on the brake pedal and turn the ignition control knob to the START position When the engine begins cranking let go of the ignition control knob it will return to the ON RUN position If the transmitter is not in the vehicle or something is interfering with the transmitter the Driver Information Center DIC will display Electronic Key Not Detected See DIC Warnings and Messages on page 3 54 for more information If the battery in the keyless access transmitter needs replacing the DIC displays
415. steering system See Steering on page 4 9 3 64 This message displays if a problem is detected with the speed variable assist steering system When this message is displayed you may notice that the effort required to steer the vehicle increases or feels heavier but you will still be able to steer the vehicle Service StabiliTrak This message displays if there has been a problem detected with the StabiliTrak system If this message comes on while you are driving pull off the road as soon as possible and stop carefully Try resetting the system by turning the ignition off then back on If this message still stays on or comes back on again while you are driving your vehicle needs service Have the StabiliTrak system inspected by your dealer retailer as soon as possible See StabiliTrak System on page 4 8 for more information Service Theft Deterrent System This message displays when there is a problem with the theft deterrent system programmed in the key A fault has been detected in the system which means that the system is disabled and it is not protecting the vehicle The vehicle usually restarts however you may want to take the vehicle to your dealer retailer before turning off the engine See Immobilizer Operation Key Access on page 2 28 or Immobilizer Operation Keyless Access on page 2 30 for more information Service Tire Monitor System This message displays if a part on the Tire Pressure Monitor System
416. sure from the parking pawl in the transmission so you can pull the shift lever out of PARK P Shifting Out of PARK P This vehicle is equipped with an electronic shift lock release system The shift lock release is designed to e Prevent ignition key Key Access removal unless the shift lever is in PARK P with the shift lever button fully released and e Prevent movement of the shift lever out of PARK P unless the ignition is in ON RUN or ACC ACCESSORY and the regular brake pedal is applied The shift lock release is always functional except in the case of an uncharged or low voltage less than 9 volt battery If your vehicle has an uncharged battery or a battery with low voltage try charging or jump starting the battery See Jump Starting on page 5 44 for more information To shift out of PARK P use the following 1 Apply the brake pedal 2 Then press the shift lever button 3 Move the shift lever to the desired position 2 45 If you still are unable to shift out of PARK P 1 Fully release the shift lever button 2 While holding down the brake pedal press the shift lever button again 3 Move the shift lever to the desired position If you still cannot move the shift lever from PARK P consult your dealer retailer or a professional towing service 2 46 Parking Your Vehicle Manual Transmission Before you get out of your vehicle place the shift lever in REVERSE R and firmly apply the parking
417. sure to read the inflator instructions and 6 Push the air only hose F onto the tire valve stem inflate the tire to its recommended pressure and push the lever down to secure in place Do not exceed 36 psi 248 kPa 7 Plug the air compressor accessory plug C into an accessory power outlet in the vehicle See i Accessory Power Outlet s on page 3 21 for more 9 Push the sealant and compressor kit switch to information the on position 5 100 Removal and Installation of the Sealant Canister 10 Inflate the tire up to the recommended inflation pressure using the air pressure gage on the top of the unit The pressure gage read high while the compressor is running Turn the compressor off to get an accurate reading 11 Turn off the air compressor by pushing the switch to the O off position To remove the sealant canister Z CAUTION Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury In a sudden stop or collision loose equipment could strike someone Store the tire sealant and compressor kit in the proper place 12 Disconnect the compressor inflator hose and wrap the hose in the bottom of the sealant and compressor kit 13 Place the equipment in the original location of your vehicle Unlock the air compressor hose from the sealant canister by pulling up on the lever Pull the air only hose F from the se
418. system is disarmed when the key is turned to ON RUN You do not have to manually arm or disarm the system The security light will come on if there is a problem with arming or disarming the theft deterrent system The key uses a transponder that matches an immobilizer control unit in your vehicle and automatically disarms the system Only the correct key will start the vehicle If the key is ever damaged you may not be able to start your vehicle When trying to start the vehicle if the engine does not start and the security light comes on there may be a problem with your theft deterrent system Turn the ignition off and try again If the engine still does not start and the key appears to be undamaged try another ignition key At this time you may also want to check the fuse See Fuses and Circuit Breakers on page 5 122 If the engine still does not start with the other key your vehicle needs service If your vehicle does start the first key may be faulty See your dealer retailer who can service the theft deterrent system and have a new key made It is possible for the theft deterrent system decoder to learn the transponder value of a new or replacement key Up to 10 keys can be programmed for the vehicle The following procedure is for programming additional keys only To program a new key do the following 1 Verify that the new key has stamped on it 2 Insert the current driver s key in the ignition and start
419. t The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times and wear safety belts properly Off Road Recovery You may find that your vehicle s right wheels have dropped off the edge of a road onto the shoulder while you are driving If the level of the shoulder is only slightly below the pavement recovery should be fairly easy Ease off the accelerator and then if there is nothing in the way steer so that your vehicle straddles the edge of the pavement You can turn the steering wheel up to one quarter turn until the right front tire contacts the pavement edge Then turn the steering wheel to go straight down the roadway 4 12 Passing Passing another vehicle on a two lane road can be dangerous To reduce the risk of danger while passing we suggest the following tips e Look down the road to the sides and to crossroads for situations that might affect a successful pass If in doubt wait e Watch for traffic signs pavement markings and lines that could indicate a turn or an intersection Never cross a solid or double solid line on your side of the lane e Do not get too close to the vehicle you want to pass Doing so can reduce your visibility e Wait your turn to pass a slow vehicle e When you are being passed ease to the right Loss of Control Let us review what driving experts say about what happens when the three control systems br
420. t Low Beam Headlamp EMIS 1 DISPLY O BEAM r Beam ore LT LO BEAM Left Low Beam Headlamp BOMS Body ControlModule g Transmission Control Module EVEN COILS TCM BATT Battery BCM 6 Body Control Module 6 DRLRT Right Daytime Running Lamp DRL Bou Pori Conifal Module SPARE ODD COILS _ Odd Coils ABS Antilock Brake System BOM Poni Sonttal Module HORN LT HI BEAM Left High Beam Headlamp WSW PUMP Windshield Washer Pump PWR MODING PassKey Module Body Control A C CLTCH Air Conditioning Compressor Clutch Module DRLENG Driver Module Wash EMIS 2 HDM WASH Headlamp Driver Module Washer Adaptive Forward Lighting System RT HIBEAM _ Right High Beam Headlamp J CaseFuses Usage NAVMTR igati FAN 2 Cooling Fan 2 a r aN SPARE FRT FOG Front Fog Lamps p m SPARE BCM 5 Body Control Module 5 pa Dayti R ing L DRL a tn iad Steering Wheel Illumination PUMP aytime Running Lamps DRL 5 124 J CaseFuses Usage J Relays Usage STRTR IGN1 Ignition 1 TRANS PUMP STRTR WSW HTR Windshield Washer Heater PWR TRN B Brake Vacuum Pump REAR DEFOG Rear Defogger HI BEAM High Beam Headlamp BLWR Daytime Running Lamps ABS MTR Antilock Brake System Motor DRL W O HID without High Intensity Discharge REAR DEFOG Rear Defogger LO BEAM HID Low Beam Headlamps High SPARE ae p Windshield Wiper WPR HI Windshield Wiper High Speed Relays Usage HEAD LAMP FAN 2 Cooling Fan 2 WASH Headlamp Washer FAN S P Cooling Fan Series Parall
421. t is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly Your vehicle has indicators as a reminder to buckle your safety belts See Safety Belt Reminders on page 3 32 In most states and in all Canadian provinces the law requires wearing safety belts Here is why You never know if you will be in a crash If you do have a crash you do not know if it will be a serious one A few crashes are mild and some crashes can be so serious that even buckled up a person would not survive But most crashes are in between In many of them people who buckle up can survive and sometimes walk away Without belts they could have been badly hurt or killed After more than 40 years of safety belts in vehicles the facts are clear In most crashes buckling up does matter a lot Why Safety Belts Work When you ride in or on anything you go as fast as it goes Put someone on it Take the simplest vehicle Suppose it is just a seat on wheels Get it up to speed Then stop the vehicle The rider does not stop The person keeps going until stopped by something In a real vehicle it could be the windshield or the inst
422. t the extension Track names longer than 32 characters are shortened Parts of words on the last page of text and the extension of the filename is not displayed The HDD Radio will display file names with the extension Preprogrammed Playlists Preprogrammed playlists that were created using WinAmp MusicMatch or Real Jukebox software can be accessed however they cannot be edited using the radio These playlists are special folders containing compressed audio song files Playlists must have a file extension of PLS or M3U Playlists can be selected using the previous and next folder buttons Tracks can be changed by pressing the seek buttons or turning the tune knob Songs are played sequentially press the lt 1 REV or D gt FWD to reverse or advance through the playing song The HDD Radio does not support preprogrammed playlists To create a playlist on the HDD radio from songs recorded to the HDD see Saving HDD Favorites earlier in this section 3 103 Playing an MP3 WMA Insert a CD partway into the slot Single CD Player or press the load button and wait for the message to insert disc Six Disc CD Player label side up The player pulls in the CD and should begin playing For the Single CD Player the track number displays at the left and center of the screen A Shuffle label appears below Press the pushbutton located under the Shuffle label to play the MP3 WMA files of the CD in random order For
423. t will have a label saying that it meets federal motor vehicle safety standards The restraint manufacturer s instructions that come with the restraint state the weight and height limitations for a particular child restraint In addition there are many kinds of restraints available for children with special needs 1 38 A CAUTION Newborn infants need complete support including support for the head and neck This is necessary because a newborn infant s neck is weak and its head weighs so much compared with the rest of its body In a crash an infant in a rear facing seat settles into the restraint so the crash forces can be distributed across the strongest part of an infant s body the back and shoulders Infants should always be secured in appropriate infant restraints Child Restraint Systems A CAUTION The body structure of a young child is quite unlike that of an adult or older child for whom the safety belts are designed A young child s hip bones are still so small that the vehicle s regular safety belt may not remain low on the A rear facing infant seat A provides restraint with the seating surface against the back of the infant hip bones as it should Instead it may settle up around the child s abdomen In a crash the belt would apply force on a body area that is unprotected by any bony structure This alone could cause serious or fatal injuries Young children should always be secured
424. tal Theater Systems Inc Corporation Y DO DoLBy gracenote DIGITAL Music recognition technology and related data are Dolby is manufactured under license from Dolby provided by Gracenote Gracenote is the industry Laboratories Dolby and the double D symbol standard in music recognition technology and related are trademarks of Dolby Laboratories content delivery For more information visit www gracenote com Litho in U S A Part No 15864564 A First Printing 2007 General Motors Corporation All Rights Reserved This manual includes the latest information at the time it was printed We reserve the right to make changes after that time without notice For vehicles first sold in Canada substitute the name General Motors of Canada Limited for Cadillac Motor Car Division whenever it appears in this manual This manual describes features that may be available in this model but your vehicle may not have all of them For example more than one entertainment system may be offered or your vehicle may have been ordered without a front passenger or rear seats Keep this manual in the vehicle for quick reference Canadian Owners A French language copy of this manual can be obtained from your dealer retailer or from Helm Incorporated P O Box 07130 Detroit MI 48207 1 800 551 4123 www helminc com Propri taires Canadiens On peut obtenir un exemplaire de ce guide en frangais aupr s de concessionnaire ou
425. tates Canada This light should come on briefly when you turn the ignition to ON RUN If it does not come on then have it fixed so it will be ready to warn you if there is a problem When the ignition is on the brake system warning light will also come on when you set your parking brake The light will stay on if your parking brake does not release fully If it stays on after your parking brake is fully released it means you have a brake problem If the light comes on while you are driving pull off the road and stop carefully You may notice that the pedal is harder to push or the pedal may go closer to the floor It may take longer to stop If the light is still on have the vehicle towed for service See Towing Your Vehicle on page 4 27 A CAUTION Your brake system may not be working properly if the brake system warning light is on Driving with the brake system warning light on can lead to an accident If the light is still on after you have pulled off the road and stopped carefully have the vehicle towed for service 3 37 Antilock Brake System Warning Light For vehicles with the Antilock Brake System ABS this light comes on briefly when the engine is started That is normal If the light does not come on then have it fixed so it will be ready to warn you if there is a problem If the ABS light stays on turn the ignition off if the light comes on when you are driving stop as soon as it is sa
426. tens 3 31 Garage Door Opener ccceeeeeeeeeneee een eeeeenes 2 56 Gasoline OCTAN iia cieectteieees oie haan ine ee 5 5 Specifications ce eeeeeeeeeeee eee eee eee eeneeeeeneeeees 5 6 GIOVE BOX isinan anna e enian EEE UTE NEEF 2 61 GM Mobility Reimbursement Program 5 7 6 Hazard Warning Flashers seceeeeeeeeee eee eee 3 6 Head Resttai ts sscicccccsdiecs conc sacavedenweamemnetacmeand nats 1 2 Headlamp AMINO secera E E 5 51 Headlamps 2 225 cscs ciceade cain dea satddansnes mededaensss 3 16 Adaptive Forward Lighting System 3 18 Bulb Replacement ceceeeeeeeeeeeeeeeeeees 5 55 Daytime Running Lamps 0eceeeeeeeeee ees 3 17 FlASM O PASS poera a 3 9 Front Turn Signal and Fog Lamps 5 56 Headlamps cont Halogen BUDS svcsscsnssavtesaicetesenestcanamegeatanuees 5 55 High Intensity Discharge HID Lighting 5 55 High Low Beam Changer eeeeeeeee 3 8 ON Reminder s nciiciciececeencecctetaeew ends ncemabtereaness 3 17 Washer reour E tel elec needs 3 13 Wiper Activated sacipta roaa 3 17 Heated Seats wcisctie disigial sien castes eves 1 6 Heater inc neni sbedtecaeadurnesentetaees ENES 3 23 Highbeam On Light rrsesiessisicnrirrininisisenassess 3 46 High Speed Operation Tires c eeeeeeeeeeeees 5 69 Highway HYPNOSIS si 02 ce ccttiennecensneanmueieeeatine 4 16 Hill and Mountain Roads n e 4 17 Hood
427. terpoint Centerpoint produces a full vehicle surround sound listening experience from CD non 5 1 surround sound DVD A MP3 WMA AUX auxiliary input or XM digital audio source and will deliver five independent audio channels from conventional two channel stereo recording 3 85 This feature is not available in AM FM radio mode If your vehicle is equipped with the Bose 5 1 Cabin Surround sound system your radio can support the playback of 5 1 Surround Sound DVD A discs or DTS 5 1 Surround Sound CD discs When a 5 1 Surround Sound formatted disc is playing DSP options available are 5 1 Surround Normal Best for all seating positions 5 1 Surround Rear Best for the rear seating position Configuring Radio Functions CONFIG Press to display FAV AUTO VOL XM if equipped or HDD if available and Back See the information provided in this radio section to learn more options about the FAV AUTO VOL XM and HDD if available label functions See Speed Compensated Volume SCV or Noise Compensation Technology earlier for information on the AUTO VOL label Press the pushbutton located under the Back label to go back to the previous display 3 86 Radio Message Locked Displays when the THEFTLOCK system has locked up the radio Take the vehicle to your dealer retailer for service If any error occurs repeatedly or if an error cannot be corrected contact your dealer retailer
428. the steering wheel left and right while you turn the key hard If none of this works then your vehicle needs service A LOCK OFF This is the only position in which the key can be inserted or removed This position locks the ignition and shifter on automatic transmission vehicles and the ignition and steering wheel on manual transmission vehicles B ACC ACCESSORY This position lets you use things like the radio and the windshield wipers when the engine is off This position allows you to turn off the engine C ON RUN This position is for driving It is the position the ignition switch returns to after the engine starts and the key is released 2 32 To shift the transmission out of PARK P the ignition key has to be in ACC ACCESSORY or ON RUN The battery could be drained if the key is left in the ACC ACCESSORY or ON RUN position with the engine off The vehicle might not start if the battery is allowed to drain for an extended period of time D START This position starts the engine Key In the Ignition Never leave your vehicle with the keys inside as it is an easy target for joy riders or thieves A chime sounds when the driver s door is opened while the vehicle is parked and the key is left in the ignition Always remember to remove the key from the ignition and take it with you This will lock the ignition and transmission Also always remember to lock the doors The battery could be drained if the key
429. the airbags are off See Passenger Airbag Status Indicator on page 3 34 If a child restraint has been installed and the on indicator is lit turn the vehicle off Remove the child restraint from the vehicle and reinstall the child restraint following the child restraint manufacturer s directions and refer to Securing a Child Restraint in the Right Front Seat Position on page 1 51 1 65 If after reinstalling the child restraint and restarting the vehicle the on indicator is still lit check to make sure that the vehicle s seatback is not pressing the child restraint into the seat cushion If this happens slightly recline the vehicle s seatback and adjust the seat cushion if possible Also make sure the child restraint is not trapped under the vehicle head restraint If this happens adjust the head restraint See Head Restraints on page 1 2 Remove any additional material from the seat such as blankets cushions seat covers seat heaters or seat massagers before reinstalling or securing the child restraint If the on indicator is still lit secure the child in the child restraint in a rear seat position in the vehicle and check with your dealer retailer The passenger sensing system is designed to enable may inflate the right front passenger s frontal airbag and seat mounted side impact airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger s seat When the pass
430. the arm 7 Reinstall the wiper blade assembly by sliding it over Allowing the wiper blade arm to touch the windshield the wiper arm to engage the J hooked end Pull up when no wiper blade is installed could damage on the assembly to lock it into place the windshield Any damage that occurs would not 8 Repeat the steps for the other wiper be covered by your warranty Do not allow the wiper blade arm to touch the windshield 6 Replace the blade with a new one 5 58 Tires CAUTION Continued Your new vehicle comes with high quality tires made by a leading tire manufacturer If ath Underinflated tires pose the same have questions about your tire warranty and where d anger as overloaded tires The to obtain service see your vehicle Warranty resurting accident could cause serio s pase IOT eelale injury Check all tires frequently to maintain the recommended pressure Tire pressure should be checked when your tires are cold See nflation Tire Pressure on page 5 67 Overinflated tires are more likely to be cut punctured or broken by a sudden impact such as when you hit a pothole Keep tires at the recommended pressure Worn old tires can cause accidents If your tread is badly worn or if your tires have been damaged replace them See High Speed Operation on page 5 69 for inflation pressure adjustment for high speed driving A CAUTION e Poorly maintained and improperly used tires are dangerous e Overloading y
431. the compact spare tire with a full size tire as soon As vying Nut C Jack as you can B Compact Spare D Wheel Wrench Tire or Flat Tire E Extension valve stem down F Strap 5 110 Compact Spare Tire If your vehicle is equipped with a compact spare tire it was fully inflated when the vehicle was new it can lose air after a time Check the inflation pressure regularly It should be 60 psi 420 kPa After installing the compact spare on the vehicle stop as soon as possible and make sure the spare tire is correctly inflated The compact spare is made to perform well at speeds up to 65 mph 105 km h for distances up to 3 000 miles 5 000 km so you can finish your trip and have the full size tire repaired or replaced at your convenience Of course it is best to replace the spare with a full size tire as soon as possible The spare tire will last longer and be in good shape in case it is needed again Notice When the compact spare is installed do not take your vehicle through an automatic car wash with guide rails The compact spare can get caught on the rails That can damage the tire and wheel and maybe other parts of your vehicle Do not use the compact spare on other vehicles And do not mix the compact spare tire or wheel with other wheels or tires They will not fit Keep the spare tire and its wheel together Notice Tire chains will not fit your compact spare Using them can damage your vehicle and can damage t
432. the coolant surge tank pressure cap off start the engine and let it run until you can feel the upper radiator hose getting hot The upper radiator hose is the top hose coming out of the radiator on the passenger s side of the vehicle Watch out for the engine cooling fans By this time the coolant level inside the coolant surge tank may be lower If the level is lower add more of the proper mixture to the coolant surge tank until the level reaches the FROID FULL COLD line on the side of the coolant surge tank 5 Then replace the pressure cap Be sure the pressure cap is hand tight and fully seated Recheck the coolant level in the bottle next time you use your vehicle to insure the system is full when cold 3 Fill the coolant surge tank with the proper mixture See Engine Coolant on page 5 27 to slightly above the FROID FULL COLD line on the side of the coolant surge tank 5 37 Power Steering Fluid See Engine Compartment Overview on page 5 14 for the location of the power steering fluid reservoir AR When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise A fluid loss in this system could indicate a problem Have the system inspected and repaired 5 38 How to Check Power Steering Fluid To check the power steering fluid do the following 1 Turn the key off and let the engine compartme
433. the engine If the engine will not start see your dealer retailer for service 3 After the engine has started turn the key to LOCK OFF and remove the key 4 Insert the key to be programmed and turn it to ON RUN within five seconds of the ignition being turned to LOCK OFF in Step 3 5 The security light will turn off once the key has been programmed It may not be apparent that the security light went on due to how quickly the key is programmed 6 Repeat the Steps 1 through 4 if additional keys are to be programmed In an emergency contact Cadillac Roadside Service See Roadside Service on page 7 6 Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle 2 29 Immobilizer Operation Keyless Access Your vehicle has a passive theft deterrent system The system is automatically armed when the ignition control knob is turned to LOCK OFF The immobilization system is disarmed when the ignition control knob is pushed in and a valid transmitter is found in the vehicle You do not have to manually arm or disarm the system The security light will come on if there is a problem with arming or disarming the theft deterrent system The system has one or more keyless access transmitters that are matched to an immobilizer control unit in your vehicle Only a correctly matched keyless access transmitter will start the vehicle If the keyless access transmitter is ever damaged
434. the latch plate into the buckle until it clicks Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessary 1 53 5 Pull the rest of the shoulder belt all the way out of the retractor to set the lock 1 54 6 To tighten the belt push down on the child restraint pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor If you are using a forward facing child restraint you may find it helpful to use your knee to push down on the child restraint as you tighten the belt Push and pull the child restraint in different directions to be sure it is secure If the airbags are off the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started If a child restraint has been installed and the on indicator is lit turn the vehicle off Remove the child restraint from the vehicle and reinstall the child restraint If after reinstalling the child restraint and restarting the vehicle the on indicator is still lit check to make sure that the vehicle s seatback is not pressing the child restraint into the seat cushion If this happens slightly recline the vehicle s seatback and adjust the seat cushion if possible Also make sure the child restraint is not trapped under the vehicle head restraint If this happens adjust the head restraint Remove a
435. the operation of your vehicle s engine radio or other systems and even damage them Your vehicle s systems may interfere with the operation of sound equipment that has been added Your vehicle has a feature called Retained Accessory Power RAP With RAP the audio system can be played even after the ignition is turned off See Retained Accessory Power RAP on page 2 34 for more information 3 80 Radio s Full View of Radio with CD shown Radio with Six Disc CD similar Partial View of Radio with DVD Audio Hard Disc Drive HDD and USB Your vehicle may have one of these radios as its audio system If your vehicle does not have one of these radio systems it may have a navigation radio system See the Navigation System manual for more information on the navigation audio system If your vehicle has one of these radios it has either a Bose sound system or a Bose 5 1 Cabin Surround sound system See Digital Signal Processing DSP later in this section for more information on the Bose 5 1 Cabin Surround sound system The radio with DVD Audio HDD and USB utilizes Gracenote technology to provide Song Artist Aloum and Genre information for many CD audio discs and is capable of playing DVD A and DTS encoded discs DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems Inc Manufactured under license from Dolby Laboratories Do
436. the outside To cancel the rear door security lock do the following 1 Unlock the door and open it from the outside 2 Insert the key into the security lock slot and turn it so the slot is in the vertical position Lockout Protection If the power door lock switch is pressed when the key is in the ignition and a door is open all the doors will lock and only the driver s door will unlock If you close the doors they can be locked by using the Remote Keyless Entry RKE transmitter Be sure to remove the key from the ignition when locking your vehicle This feature can be overridden by pressing the lock button on the RKE transmitter or by pressing the power lock switch a second time On vehicles with a Keyless Access System the system can be programmed to alert you when all the doors are closed and a transmitter has been left inside of the vehicle See DIC Vehicle Customization on page 3 68 for more information 2 20 Trunk A CAUTION It can be dangerous to drive with the trunk lid open because carbon monoxide CO gas can come into your vehicle You cannot see or smell CO It can cause unconsciousness and even death If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid e Make sure all other windows are shut e Turn the fan on your heating or cooling system to its highest speed and select the control setting that wil
437. the sealant evenly in the tire Stop at a safe location and check the tire pressure refer to Steps 1 through 8 under Using the Air Compressor without Sealant next in this section If the tire pressure has fallen more then 10 psi 68 kPa below the recommended inflation pressure stop driving the vehicle The tire is too severely damaged and the tire sealant and compressor kit cannot seal the tire See Roadside Service on page 7 6 for more information If the tire pressure has not dropped more than 10 psi 68 kPa from the recommended inflation pressure you can inflate the tire back up to the recommended inflation pressure Wipe off any sealant from the wheel tire and vehicle with a rag Dispose of the sealant canister at a local dealer retailer or in accordance with your local state codes and practices After using the sealant canister replace it with a new canister from your dealer retailer After temporarily sealing a tire with the tire sealant and compressor kit take your vehicle to your dealer retailer to have the tire inspected and repaired 5 90 Using the Air Compressor without Sealant to Inflate an Underinflated Tire Not Punctured To use the air compressor to inflate a tire with air only and not sealant Your tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses balls etc A CAUTION Idli
438. this happens you and other vehicle occupants could drown Do not ignore police warnings and be very cautious about trying to drive through flowing water Hydroplaning Hydroplaning is dangerous Water can build up under your vehicle s tires so they actually ride on the water This can happen if the road is wet enough and you are going fast enough When your vehicle is hydroplaning it has little or no contact with the road There is no hard and fast rule about hydroplaning The best advice is to slow down when the road is wet Other Rainy Weather Tips Besides slowing down other wet weather driving tips include e Allow extra following distance Pass with caution Keep windshield wiping equipment in good shape Keep the windshield washer fluid reservoir filled Have good tires with proper tread depth See Tires on page 5 59 Before Leaving on a Long Trip To prepare your vehicle for a long trip consider having it serviced by your dealer retailer before departing Things to check on your own include Windshield Washer Fluid Reservoir full Windows clean inside and outside Wiper Blades In good shape Fuel Engine Oil Other Fluids All levels checked e Lamps Do they all work and are lenses clean e Tires Are treads good Are tires inflated to recommended pressure e Weather and Maps Safe to travel Have up to date maps Highway Hypnosis Always be alert and pay attention to your surroundings
439. tion increased road noise and shorter tread life After switching to winter tires be alert for changes in vehicle handling and braking See your dealer retailer for details regarding winter tire availability and proper tire selection Also see Buying New Tires on page 5 77 If you choose to use winter tires e Use tires of the same brand and tread type on all four wheel positions e Use only radial ply tires of the same size load range and speed rating as the original equipment tires Winter tires with the same speed rating as your original equipment tires may not be available for H V W Y and ZR speed rated tires If you choose winter tires with a lower speed rating never exceed the tire s maximum speed capability Tire Sidewall Labeling Useful information about a tire is molded into its sidewall The examples below show a typical passenger vehicle tire and a compact spare tire sidewall ES 4109 MS S K lt 2si60R 16 9 gt s pe DOT MaLgae oxy af Z W es AT x A oF pers y Bavo ona a A by por Z Hovis oz aY Passenger P Metric Tire Example A Tire Size The tire size is a combination of letters and numbers used to define a particular tire s width height aspect ratio construction type and service description See the Tire Size illustration later in this section for more detail B TPC Spec Tire Performance Criteria Specification Original equipment tires designed
440. to apply the regular brake at once should the vehicle begin to move Park on a fairly steep hill with the vehicle facing downhill Keeping your foot on the regular brake set the parking brake e To check the parking brake s holding ability With the engine running and transmission in NEUTRAL N slowly remove foot pressure from the regular brake pedal Do this until the vehicle is held by the parking brake only e To check the PARK P mechanism s holding ability With the engine running shift to PARK P Then release the parking brake followed by the regular brake Contact your dealer retailer if service is required Underbody Flushing Service At least every spring use plain water to flush any corrosive materials from the underbody Take care to clean thoroughly any areas where mud and other debris can collect Tire Sealant and Compressor Kit Usage Fluid Lubricant Check the sealant expiration date printed on the 50 50 mixture of clean drinkable instruction label of the Tire Sealant and Compressor i water and use only DEX COOL Kit if equipped at least once a year See your Engine Coolant Coolant See Engine Coolant on dealer retailer for a replacement canister page 5 27 Hydraulic Brake Delco Supreme 11 Brake Fluid or Recommended Fluids and equivalent DOT 3 brake fluid Lubricants a Optikleen Washer Solvent Fluids and lubricants identified below by name part ificati be obtained f H
441. to the key lock cylinder located on the outside of the driver s door 4 Turn the key to the unlock position five times within five seconds 5 The Driver Information Center DIC will display Ready To Learn Electronic Key X where X can be 2 3 or 4 Place the new unrecognized transmitter into the transmitter pocket with the transmitter buttons facing the front of the vehicle The transmitter pocket is inside the center console storage area located between the driver and front passenger seats Once the transmitter is programmed a beep will sound The DIC will display Ready To Learn Electronic Key X where X can be 3 or 4 or Maximum Electronic Keys Learned Press the ignition control knob to exit programming mode Remove the transmitter from the transmitter pocket and press the unlock button on the keyless access transmitter two times 2 11 The Canadian immobilizer standard requires Canadian 3 owners to see their dealer retailer for matching new transmitters when two recognized transmitters are not 4 available United States owners are permitted to match a new transmitter to their vehicle when a recognized transmitter is not available 5 The procedure will require three ten minute cycles to complete the matching process 6 1 The vehicle must be off 7 2 Place the new unrecognized transmitter into the transmitter pocket with the transmitter buttons facing the front of the vehicle
442. tomization capabilities that allow you to program certain features to one preferred setting Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers All of the customization options may not be available on your vehicle Only the options available will be displayed on the DIC The default settings for the customization features were set when your vehicle left the factory but may have been changed from their default state since then The customization preferences are automatically recalled To change customization preferences use the following procedure Entering the Feature Settings Menu 1 Turn the ignition on To avoid excessive drain on the battery it is recommended that the headlamps are turned off 2 Press the customization button to enter the feature settings menu 3 68 Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle Display In English This feature will only display if a language other than English has been set This feature allows you to change the language in which the DIC messages appear back to English Press the customization button until the Press vV To Display In English screen appears on the DIC display Press the set reset button once to select English as the language in which all DIC messages will appear Display Language Thi
443. tting in a seat that has a lap shoulder belt but the shoulder part is behind the child In a crash the child would not be restrained by the shoulder belt The child might slide under the lap belt The belt force would then be applied right on the abdomen That could cause serious or fatal injuries The child could also move too far forward increasing the chance of head and neck injury The shoulder belt should go over the shoulder and across the chest 1 34 Infants and Young Children Everyone in a vehicle needs protection This includes infants and all other children Neither the distance traveled nor the age and size of the traveler changes the need for everyone to use safety restraints In fact the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle A CAUTION Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten Never leave children unattended in a vehicle and never allow children to play with the safety belts Every time infants and young children ride in vehicles they should have the protection provided by appropriate restraints Children who are not restrained properly can strike other people or can be thrown out of the vehicle In addition young children should not use the vehicle s adult safety belts alone they need to use a child restra
444. ty A Weight for dea kg A Weight for 483 ko Example 2 9 Example 3 9 Subtract Occupant Subtract Occupant 1 000 Ibs Weight 150 Ibs 750 Ibs 340 kg Weight 200 Ibs 453 kg 68 kg x5 91 kg x5 g Available Cargo Available Cargo Weight 250 Ibs 113 kg ca Weight 0 Ibs 0 kg Refer to your vehicle s Tire and Loading Information label for specific information about your vehicle s capacity weight and seating positions The combined weight of the driver passengers and cargo should never exceed your vehicle s capacity weight 4 25 Certification Label GM MFD BY GENERAL MOTORS CORP mt DATE GWR GAWRFRT THIS VEHICLE CONFORMS TO ALL gag Na OTOR VEHICLE SAFETY BUMPER NTION STANDARDS IN EFFECT ON THE D FM WN ABOVE 2007 ASS CAR a A vehicle specific Certification label is attached to either the driver s door edge or the lower center pillar on the driver s side of the vehicle This label shows the gross weight capacity of your vehicle called the Gross Vehicle Weight Rating GVWR The GVWR includes the weight of the vehicle all occupants fuel and cargo 4 26 The Certification label also shows the maximum weights for the front and rear axles called the Gross Axle Weight Rating GAWR Never exceed the GVWR or the GAWR for either the front or rear axle A CAUTION Do not load your vehicle any heavier than the Gross Vehicle Weight Rating
445. ual noise A fluid loss could indicate a problem Have it inspected and repaired 5 49 How to Check Lubricant A Drain Plug B Fill Plug To get an accurate reading the vehicle should be ona level surface 5 50 If the level is below the bottom of the filler plug hole located on the transfer case you ll need to add some lubricant Add enough lubricant to raise the level to the bottom of the filler plug hole Use care not to overtighten the plug What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use See Recommended Fluids and Lubricants on page 6 11 Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise A fluid loss could indicate a problem Have it inspected and repaired How to Check Lubricant To get an accurate reading the vehicle should be on a level surface If the level is below the bottom of the filler plug hole located on the rear axle you ll need to add some lubricant Add enough lubricant to raise the level to the bottom of the filler plug hole What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use See Recommended Fluids and Lubricants on page 6 11 Headlamp Aiming The vehicle has a visual optical headlamp aiming system The aim has been preset at the factory and should need no further adjustment However if the
446. uced the next time the vehicle is driven The vehicle may be driven at a reduced speed while this message is on but acceleration and speed may be reduced Anytime this message stays on the vehicle should be taken to your dealer retailer for service as soon as possible Fuel Level Low This message displays when your vehicle is low on fuel Refill the fuel tank as soon as possible A chime may sound when this message displays See Filling the Tank on page 5 8 Heated Washer Fluid Wash Washer Wipes Pending If your vehicle has this feature this message displays when you turn on the heated windshield washer fluid system See Heated Windshield Washer under Windshield Washer on page 3 11 for more information 3 60 Heated Washer Fluid System Off If your vehicle has this feature this message displays when you manually turn off the heated windshield washer fluid system or when the system automatically turns off See Heated Windshield Washer under Windshield Washer on page 3 11 for more information This message clears itself after 10 seconds Hood Open This message displays when the hood is not closed completely Make sure that the hood is closed completely Ice Possible Drive With Care This message displays when the outside temperature is cold enough to create icy road conditions Adjust your driving accordingly Learn Delay Active Wait XX Min Minutes If your vehicle has the keyless access system this
447. uctions and inflate the tire to its recommended pressure Do not exceed 36 psi 248 kPa 8 Plug the air compressor accessory plug C into an accessory power outlet in the vehicle See Accessory Power Outlet s on page 3 21 for more information Do not slam the door or close the window on the 10 Push the On Off switch to the on position air compressor accessory plug The sealant and compressor kit will inject sealant and air into the tire Sealant may leak from the puncture until the vehicle is driven and the hole has A CAUTION sealed The pressure gage will initially show a high pressure Idling the engine in a closed in place or with while the compressor pushes the sealant into the the climate control system off can cause tire Once the sealant is completely dispersed deadly carbon monoxide CO See Engine into the tire the pressure will quickly drop and start Exhaust on page 2 47 to rise again as the tire inflates with air 9 Start the vehicle See Starting the Engine on page 2 34 for more information The vehicle must be running while using the air compressor 5 96 11 Inflate the tire to the recommended inflation pressure found on the Tire and Loading Information label using the air pressure gage on the top of the unit See Inflation Tire Pressure on page 5 67 The pressure gage reads high while the compressor is running Turn the compressor off to get an accurate pressure reading Notice If the rec
448. und the restraint The child restraint instructions will show you how 1 49 3 Push the latch plate into the buckle until it clicks Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessary 1 50 4 Pull the rest of the shoulder belt all the way out of the retractor to set the lock 5 To tighten the belt push down on the child restraint pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor If you are using a forward facing child restraint you may find it helpful to use your knee to push down on the child restraint as you tighten the belt 6 If your child restraint has a top tether follow the child restraint manufacturer s instructions regarding the use of the top tether See Lower Anchors and Tethers for Children LATCH on page 1 43 for more information 7 Push and pull the child restraint in different directions to be sure it is secure To remove the child restraint unbuckle the vehicle s safety belt and let it go back all the way If the top tether is attached to a top tether anchor disconnect it Securing a Child Restraint in the Right Front Seat Position Your vehicle has airbags A rear seat is a safer place to secure a forward facing child restraint See Where to Put the Restraint on page 1 42 In addition your vehicle has a passenger sensing system which is design
449. uphill grade shift down to a lower gear and reduce your speed to around 45 mph 70 km h to reduce the possibility of engine and transmission overheating Parking on Hills A CAUTION You really should not park your vehicle with a trailer attached on a hill If something goes wrong your rig could start to move People can be injured and both your vehicle and the trailer can be damaged But if you ever have to park your rig on a hill here is how to do it 1 Apply your regular brakes but do not shift into PARK P yet 2 Have someone place chocks under the trailer wheels 3 When the wheel chocks are in place release the regular brakes until the chocks absorb the load 4 Reapply the regular brakes Then apply your parking brake and then shift to PARK P 5 Release the regular brakes When You Are Ready to Leave After Parking on a Hill 1 Apply your regular brakes and hold the pedal down while you e Start your engine e Shift into a gear e Release the parking brake 2 Let up on the brake pedal 3 Drive slowly until the trailer is clear of the chocks 4 Stop and have someone pick up and store the chocks Maintenance When Trailer Towing Your vehicle will need service more often when you re pulling a trailer See the Maintenance Schedule for more on this Things that are especially important in trailer operation are automatic transmission fluid don t overfill engine oil drive belt cooling
450. urn the knob clockwise to brighten the lights or counterclockwise to dim them Turn the knob completely clockwise to turn on the interior lamps Entry Lighting The entry lighting system turns on the reading and dome lamps and the backlighting to the exterior lamp control when a door is opened or if the transmitter unlock button is pressed If activated by the transmitter the lighting stays on for about 25 seconds The entry lighting system uses the light sensor on the instrument panel so it must be dark outside in order for the lamps to turn on The lamps turn off about 25 seconds after the last door is closed They dim then turn off if the ignition key is turned to ON RUN They immediately turn off if the power locks are used Parade Dimming This feature does not let the instrument panel backlight dim during daylight hours while the key is in the ignition and the headlamps are on Parade dimming automatically works with the light sensor located on top of the dashboard If it is dark enough outside and the parking lamps are on the backlight on the instrument panel can be adjusted by turning the instrument panel brightness knob clockwise or counterclockwise to brighten or dim the lighting See Instrument Panel Brightness on page 3 19 3 19 Reading Lamps The reading lamps are located on the overhead console These lamps come on automatically when any door is opened For manual operation press the button next to each la
451. used to remove dust If a more thorough cleaning is necessary a soft cloth dampened with a mild soap solution can be used Allow the leather to dry naturally Do not use heat to dry Never use steam to clean leather Never use spot lifters or spot removers on leather Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of your leather and are not recommended Do not use silicone or wax based products or those containing organic solvents to clean your vehicle s interior because they can alter the appearance by increasing the gloss in a non uniform manner Never use shoe polish on leather 5 113 Instrument Panel Vinyl and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust If a more thorough cleaning is necessary a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt Never use spot lifters or removers on plastic surfaces Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended Do not use silicone or wax based products or those containing organic solvents to clean your vehicle s interior because they can alter the appearance by increasing the gloss in a non uniform manner Some commercial products may increase gloss on your instrument panel
452. ut this is normal The brakes will return to normal operation after the brake pedal has been released All Wheel Drive AWD System If your vehicle has this feature engine power is sent to all four wheels when needed During normal driving conditions the vehicle will operate in 2WD mode When the system senses a loss of traction the vehicle will automatically change to AWD mode If you have the spare tire on the vehicle there may be a reduction in performance of the AWD system Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning you can steer but it will take much more effort Speed Variable Assist Steering Your vehicle has a steering system that varies the amount of effort required to steer the vehicle in relation to the speed of the vehicle The amount of steering effort required is less at slower speeds to make the vehicle more maneuverable and easier to park At faster speeds the steering effort increases to provide a sport like feel to the steering This provides maximum control and stability If your vehicle seems harder to steer than normal when parking or driving slowly there may be a problem with the system You will still have power steering but steering will be stiffer than normal at slow speeds See your dealer retailer for service Steering Tips It is important to take curves at a reasonable speed A lot of the driver lost control
453. utomatically lock when the doors are closed and the vehicle is shifted out of PARK P At Vehicle Speed default on Manual Transmission The vehicle s doors automatically lock when the vehicle speed is above 5 mph 8 km h for three seconds No Change No change will be made to this feature The current setting will remain To select a setting press the set reset button while the desired setting is displayed on the DIC Auto Door Unlock This feature allows you to select whether or not the door s will automatically unlock It also allows you to select which doors and when they will automatically unlock See Programmable Automatic Door Locks on page 2 18 for more information Press the customization button until Auto Door Unlock appears on the DIC display Press the set reset button once to access the settings for this feature Then press the menu up down button to scroll through the following settings Off None of the doors will automatically unlock Driver At Off Only the driver s door will unlock when the ignition is turned off Driver In Park Automatic Transmission Only Only the driver s door will unlock when the vehicle is shifted into PARK P 3 69 All At Off default on Manual Transmission All of the doors will unlock when the ignition is turned off All In Park default on Automatic Transmission Automatic Transmission Only All of the doors will unlock when the vehicle is shifted into PARK P
454. utside temperature and the length of time that has elapsed since the vehicle was last driven 3 23 3 Wait for the system to regulate This may take from 10 to 30 minutes Then adjust the temperature if necessary You can switch from English to metric units through the Driver Information Center DIC See DIC Vehicle Customization on page 3 68 The air conditioning system removes moisture from the air so a small amount of water might drip underneath the vehicle while it is idling or after the engine is turned off is normal Do not cover the solar sensor located in the center of the instrument panel near the windshield For more information on the solar sensor see Sensors later in this section PASS Passenger Climate Control Press this button to set a different temperature for the passenger Then press the passenger temperature adjustment buttons to select a comfortable setting Pressing the PASS button again automatically sets the passenger s temperature to the driver s setting Turning the passenger s temperature display off does not shut the climate control system for the passenger off A V Temperature Adjustment The temperature can be adjusted separately for the driver and the passenger Press the up or down arrow buttons to increase or decrease the automatic temperature settings 3 24 Manual Operation TE Mode Press the or buttons to change the current airflow mode The current mode sel
455. utton positioned under the desired label Turn the TUNE TONE knob clockwise or counterclockwise to adjust the highlighted setting The highlighted setting can be adjusted by pressing either SEEK arrow X FWD or lt lt REV buttons until the desired levels are obtained To quickly adjust balance or fade to the middle position press the pushbutton positioned under the BAL or FADE label for more than two seconds A beep may sound and the level adjusts to the middle position To quickly adjust all speaker and tone controls to the middle position press the TUNE TONE knob for more than two seconds Digital Signal Processing DSP If your radio has this feature it is used to provide a choice of different listening experiences To choose a DSP setting perform the following steps 1 Press the TUNE TONE knob to display the tone speaker and DSP labels 2 Press the pushbutton located under the DSP label 3 Press the Back button to exit the display To return to the original display repeatedly press the Back button or wait for the display to time out The DSP settings available are e Normal Select for normal mode this provides the best sound quality for all seating positions e Driver Select to adjust the audio for the driver to receive the best possible sound quality e Rear Select to adjust the audio for the rear seat passengers to receive the best possible sound quality e Centerpoint Select to enable Bose Cen
456. ve stem Press the tire gage firmly onto the valve to get a pressure measurement If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label no further adjustment is necessary If the inflation pressure is low add air until you reach the recommended amount If you overfill the tire release air by pushing on the metal stem in the center of the tire valve Re check the tire pressure with the tire gage Be sure to put the valve caps back on the valve stems They help prevent leaks by keeping out dirt and moisture High Speed Operation A CAUTION Driving at high speeds 100 mph 160 km h or higher puts an additional strain on tires Sustained high speed driving causes excessive heat build up and can cause sudden tire failure You could have a crash and you or others could be killed Some high speed rated tires require inflation pressure adjustment for high speed operation When speed limits and road conditions are such that a vehicle can be driven at high speeds make sure the tires are rated for high speed operation in excellent condition and set to the correct cold tire inflation pressure for the vehicle load If your vehicle has 235 50ZR18 size tires they will require inflation pressure adjustment when driving your vehicle at speeds of 100 mph 160 km h or higher Set the cold inflation pressure to the maximum inflation pressure shown on the tire sidewall or 44 ps
457. vehicle is damaged in a crash the headlamp aim may be affected and adjustment may be necessary If oncoming vehicles flash their high beams at you this may also mean the vertical aim needs to be adjusted It is recommended that the vehicle is taken to your dealer retailer for service if the headlamps need to be re aimed It is possible however to re aim the headlamps as described 5 51 The vehicle should To adjust the vertical aim Be placed so the headlamps are 25 ft 7 6 m from 1 Open the hood See Hood Release on page 5 13 a light colored wall for more information e Have all four tires on a level surface which is level all the way to the wall e Be placed so it is perpendicular to the wall e Not have any snow ice or mud on it e Be fully assembled and all other work stopped while headlamp aiming is being performed e Normally loaded with a full tank of fuel and one person or 160 Ibs 75 kg sitting on the driver seat e Have all tires properly inflated e Have the spare tire is in its original location in the vehicle Headlamp aiming is done with the vehicle s low beam headlamps The high beam headlamps will be correctly aimed if the low beam headlamps are aimed properly Base Level 5 52 4 At a wall measure from the ground upward A to the recorded distance from Step 3 and mark it Uplevel 5 Draw or tape a horizontal line B the width of t
458. veral places around your vehicle Your dealer retailer and the service manual have information about servicing your vehicle and the airbag system To purchase a service manual see Service Publications Ordering Information on page 7 15 A CAUTION For up to 10 seconds after the ignition is turned off and the battery is disconnected an airbag can still inflate during improper service You can be injured if you are close to an airbag when it inflates Avoid yellow connectors They are probably part of the airbag system Be sure to follow proper service procedures and make sure the person performing work for you is qualified to do so Adding Equipment to Your Airbag Equipped Vehicle Q Is there anything might add to or change about the vehicle that could keep the airbags from working properly A Yes If you add things that change your vehicle s frame bumper system height front end or side sheet metal they may keep the airbag system from working properly Changing or moving any parts of the front seats safety belts the airbag sensing and diagnostic module steering wheel instrument panel roof rail airbag modules ceiling headliner or pillar garnish trim front sensors or airbag wiring can affect the operation of the airbag system In addition your vehicle has a passenger sensing system for the right front passenger s position which includes sensors that are part of the passenger s seat The passenger sen
459. vered at no charge if you are unable to gain entry into your vehicle A remote unlock may be available if you have an active OnStar subscription To ensure security the driver must present personal identification before lock out service is provided In Canada the vehicle registration is also required Emergency Tow From a Public Roadway or Highway Tow to the nearest dealership for warranty service or in the event of a vehicle disabling crash Winch out assistance is provided when the vehicle is mired in sand mud or snow Flat Tire Change Installation of a spare tire in good condition when equipped and properly inflated is covered at no charge The customer is responsible for the repair or replacement of the tire if not covered by a warrantable failure Jump Siart A battery jump start is covered at no charge if the vehicle does not start Trip Routing Service Upon request Cadillac Roadside Service will send you detailed computer personalized maps highlighting your choice of either the most direct route or the most scenic route to your destination anywhere in North America along with helpful travel information pertaining to your trip Please allow three weeks before your planned departure date In Canada trip routing requests will be limited to six per calendar year e Trip Interruption Benefits and Assistance If your trip is interrupted due to a warranty failure incidental expenses may be reimbursed during the 60 mont
460. w Add Oil If your vehicle has an oil level sensor this message displays if the oil level in the vehicle is low Check the oil level and correct it as necessary You may need to let the vehicle cool or warm up and cycle the ignition to be sure this message clears This message clears itself after 10 seconds until the next ignition cycle See Engine Oil on page 5 16 for additional information Engine Overheated Idle Engine Notice lf you drive your vehicle while the engine is overheating severe engine damage may occur If an overheat warning appears on the instrument panel cluster and or DIC stop the vehicle as soon as possible Do not increase the engine speed above normal idling speed See Engine Overheating on page 5 30 for more information This message displays when the engine coolant temperature is too hot Stop and allow the vehicle to idle until it cools down See Engine Coolant Temperature Warning Light on page 3 39 See Overheated Engine Protection Operating Mode on page 5 32 for information on driving to a safe place in an emergency 3 59 Engine Power Is Reduced This message displays when the engine power is being reduced to protect the engine from damage There could be several malfunctions that might cause this message Reduced engine power can affect the vehicle s ability to accelerate If this message is on but there is no reduction in performance proceed to your destination The performance may be red
461. will occur In heavy rain or snow wipes occur more frequently If the system is left on for long periods of time occasional wipes may occur without any moisture on the windshield This is normal and indicates that the Rainsense system is activated The wiper control should be left in the off position unless the wiper is needed The Rainsense system is sensitive to vibration and can activate if something hits the windshield or if the vehicle hits a bump Rainsense windshield wipers operate in a delay mode as well as a continuous low or high speed as needed Move the wiper lever up to the delay position and turn the band to one of five settings The level one or lowest setting is at the bottom of the band This setting lets more rain or snow collect on the windshield between wipes Turn the delay band forward to a higher setting to let less rain or snow collect on the windshield between wipes The top position is the highest setting A single wipe occurs each time the delay band is turned to a higher setting to indicate that the Rainsense level has been increased Notice Going through an automatic car wash with the wipers on can damage them Turn the wipers off when going through an automatic car wash The mist and wash cycles operate as normal and are not affected by the Rainsense function The Rainsense system can be overridden at any time by manually changing the wiper control to low or high speed The s
462. will be stopped after 15 seconds to prevent cranking motor damage To prevent gear damage this system also prevents cranking if the engine is already running Engine cranking can be stopped by turning the ignition switch to ACC ACCESSORY or LOCK OFF and damage the cranking motor and drain the battery Wait at least 15 seconds between each try to let the cranking motor cool down 2 If the engine does not start after 5 10 seconds especially in very cold weather below O F or 18 C it could be flooded with too much gasoline Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds Wait at least 15 seconds between each try to allow the cranking motor to cool down When the engine starts let go of the key and accelerator If the vehicle starts briefly but then stops again do the same thing This clears the extra gasoline from the engine Do not race the engine immediately after starting it Operate the engine and transmission gently until the oil warms up and lubricates all moving parts Notice The engine is designed to work with the electronics in your vehicle If you add electrical parts or accessories you could change the way the engine operates Before adding electrical equipment check with your dealer retailer If you do not your engine might not perform properly Any resulting damage would not be covered by your vehicle s Notic
463. will want to slow down and adjust your driving to these conditions It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited While driving on a surface with reduced traction try your best to avoid sudden steering acceleration or braking including reducing vehicle speed by shifting to a lower gear Any sudden changes could cause the tires to slide You may not realize the surface is slippery until your vehicle is skidding Learn to recognize warning clues such as enough water ice or packed snow on the road to make a mirrored surface and slow down when you have any doubt Remember Any Antilock Brake System ABS helps avoid only the braking skid Competitive Driving See your warranty book before using your vehicle for competitive driving Notice f you use your vehicle for competitive driving the engine may use more oil than it would with normal use Low oil levels can damage the engine Be sure to check the oil level often during competitive driving and keep the level at or near the upper mark that shows the proper operating range on the engine oil dipstick For information on how to add oil see Engine Oil on page 5 16 Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired by alcohol or drugs with night vision problems or by fatigue Night driving tips include Drive defensivel
464. xterior lamp control must be in AUTO The wiper activated headlamps immediately turn off when the ignition is turned to LOCK OFF or the windshield wiper control is turned off Headlamps on Reminder A warning chime will sound if the exterior lamp control is left on in either the headlamp or parking lamp position and the driver s door is opened with the ignition off See Lights On Reminder on page 3 46 for additional information Daytime Running Lamps DRL Daytime Running Lamps DRL can make it easier for others to see the front of your vehicle during the day DRL can be helpful in many different driving conditions but they can be especially helpful in the short periods after dawn and before sunset Fully functional daytime running lamps are required on all vehicles first sold in Canada The DRL system will make either the reduced intensity low beam headlamps or dedicated DRL s come on when the following conditions are met e Itis still daylight and the ignition is in ON RUN or START e The exterior lamp control is in off or AUTO and the headlamps are off e The automatic transmission is not in PARK P When DRL s are on only the reduced intensity low beam headlamps or dedicated DRL s will be on No other exterior lamps will be on The instrument panel cluster will not be lit up either When the exterior lamp control is in AUTO and it is dark enough outside the DRL turns off and the low beam headlamps will
465. y e Do not drink and drive e Reduce headlamp glare by adjusting the inside rearview mirror e Slow down and keep more space between you and other vehicles because your headlamps can only light up so much road ahead e Watch for animals e When tired pull off the road Do not wear sunglasses e Avoid staring directly into approaching headlamps e Keep the windshield and all glass on your vehicle clean inside and out e Keep your eyes moving especially during turns or curves No one can see as well at night as in the daytime But as we get older these differences increase A 50 year old driver might need at least twice as much light to see the same thing at night as a 20 year old Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate Always drive slower in these types of driving conditions and avoid driving through large puddles and deep standing or flowing water A CAUTION Wet brakes can cause crashes They might not work as well in a quick stop and could cause pulling to one side You could lose control of the vehicle After driving through a large puddle of water or a car vehicle wash lightly apply the brake pedal until the brakes work normally CAUTION Continued CAUTION Continued Flowing or rushing water creates strong forces Driving through flowing water could cause your vehicle to be carried away If
466. y designed to inflate if the impact exceeds a predetermined deployment threshold Deployment thresholds are used to predict how severe a crash is likely to be in time for the airbags to inflate and help restrain the occupants Whether your frontal airbags will or should deploy is not based on how fast your vehicle is traveling It depends largely on what you hit the direction of the impact and how quickly your vehicle slows down Frontal airbags may inflate at different crash speeds For example e If the vehicle hits a stationary object the airbags could inflate at a different crash speed than if the vehicle hits a moving object e If the vehicle hits an object that deforms the airbags could inflate at a different crash speed than if the vehicle hits an object that does not deform e If the vehicle hits a narrow object like a pole the airbags could inflate at a different crash speed than if the vehicle hits a wide object like a wall e If the vehicle goes into an object at an angle the airbags could inflate at a different crash speed than if the vehicle goes straight into the object Thresholds can also vary with specific vehicle design Frontal airbags are not intended to inflate during vehicle rollovers rear impacts or in many side impacts In addition your vehicle has a dual stage driver airbag Dual stage airbags adjust the restraint according to crash severity Your vehicle has electronic frontal sensors which hel
467. y electrical components on your vehicle may damage it Always keep the covers on any electrical component NOTE RELAYS TO BE INSERTED AS PER LABEL AND WITH THE CORRECT ORIENTATION AS Ca asana A OE INDICATED BY THE NOTCH EAM ARBAGIGN SPARE AN ORIENTATION DIFFERENCE FAN 2 M AL U mm OF 180 IS ACCEPTABLE ECM TCMIGN MISC IGN EMSi int D EVEN COILS FOR 4 TERMINAL RELAYS m mh a ae e NOTE INSERER LES RELAIS D APRES LES INDICATIONS SUR ETIQUETTE LINDENTATION CORRECT STRTR ON DE 180 LES RELAIS A 4 BORNES DEFOG WSWHTR BRK VAC PUMP BLWA L ODD COILS Je f 3 I RTHIBEAM NAVMTR FRTFOG O G p TRANS OIL RLY H o BEAM at WPR WPRHI C RTLO BEAM CI SPARE CI C my E LTHIBEAM PWRMODING STRAWHLALLUM PWR TRN oaansam C C4 TON gt a a I f 3 a LELI ABSMTR REAR DEFOG SPARE ABS HORN WSW PUMP A C CLTCH DRLENG PUMP HDM WASH LT LO BEAM Left Low Beam Headlamp AIRBAG IGN Airbag Switch RT LO BEAM Right Low Beam Headlamp SPARE Low Beam Daytime Running BCM 7 Body Control Module 7 LO BEAM DRL LO BEAM DRL Lamp DRL PED PROT Not Used 5 123 Fuses Usage _ __ Fuses Usage Engine Control Module ECM A WPR Windshield Wiper Transmission Control Module TCM TRAN _ ECM TCM IGN 1 IPC instrument Panel Cluster Oi Miy Transmission Oil Relay PASS Key Ill Module MISC IGN CO BEAM Right Lom Seam Hond aa RT LO BEAM Righ
468. y playing back e Playlist Sine all HDD content sE System is playing back content Artist by a selected Artist in e Albums alphabetical order Song Titles System is playing back content Album from a selected album in track e Genres order e Recently Saved Genre System is playing back content in a selected Genre in alphabetical e Audiobook order o 3 Press the MENU SELECT knob to select the Song System is playing back all songs desired option in alphabetical order Playlist System is playing back all songs Shuffle Songs a ae inthe Select this option from the HDD Menu to randomly play AudioBook System is playing back audio back HDD content book content 3 96 Playlist Select this option from the HDD Menu to display all six favorite Playlists then select one of the six playlist to display a list of songs that have been added to that favorite playlist Select a song from the list to begin playback of that song and to put the HDD into the Playlist mode See Saving HDD Favorites later in this section for more information HDD Categories The HDD category mode can be used to select a song by a particular artist album or genre for playback As an example the HDD Menu displays a layout such as Artists 5 Albums 6 Song Titles 77 Genres 3 The radio system displays the number of available items in each individual category as shown on the sample display For example the samp
469. y when work is done on the brake hydraulic system A CAUTION If your vehicle has too much brake fluid it can spill on the engine The fluid will burn if the engine is hot enough You or others could be burned and your vehicle could be damaged Add brake fluid only when work is done on the brake hydraulic system If the ignition is in ON RUN and the brake fluid is low the Service Brake System message will be displayed in the DIC See DIC Warnings and Messages on page 3 54 When the brake fluid falls to a low level the brake warning light will come on See Brake System Warning Light on page 3 37 What to Add Notice When you do need brake fluid DOT 3 brake fluid is e Using the wrong fluid can badly damage brake recommended for use DOT 4 brake fluid is also hydraulic system parts For example just a compatible with your vehicle s brake system parts few drops of mineral based oil such as engine However if you choose to use DOT 4 fluid it is oil in the brake hydraulic system can damage recommended that you flush the brake hydraulic brake hydraulic system parts so badly that they system and refill it with new DOT 4 fluid at a regular will have to be replaced Do not let someone maintenance service every two years See Additional put in the wrong kind of fluid Required Services on page 6 5 Use new brake e If you spill brake fluid on your vehicle s painted fluid from a sealed container only See Recommended surfaces the
470. ydraulic Clutch Fluid Use only ee Deena ng gree Cena Hydraulic GM Part No U S 88958860 in i Clutch System Canada 88901244 Super DOT 4 P brake fluid Usage Fluid Lubricant The engine requires a special age S ee M Part No U S 12377985 in engine oil meeting GM Standard Parking Brake Canada 88901242 or lubricant Shear tan be ee aaa or ae synthetic and should also be a Engine Oil for Gasoline Engines starburst in Canada 89021186 symbol However not all synthetic gt API oils with the starburst symbol Manual SAE 75W 90 GL5 Gear Oil will meet this GM standard Look Transmission GM Part No U S 88862475 for and use only an oil that meets in Canada 88862476 GM Standard GM4718M For the s i Automatic DEXRON VI Automatic Coosa see Engine Ol Transmission Transmission Fluid identified with the American GM Power Steering Fluid Petroleum Institute API Certified a oe GM Part No U S 89021184 Usage Fluid Lubricant Transfer Case Transfer Case Fluid All Wheel GM Part No U S 88861950 Drive in Canada 88861951 Multi Purpose Lubricant Superlube Key Lock GM Part No U S 12346241 y in Canada 10953474 Lubriplate Lubricant Aerosol GM Part No U S 12346293 in Canada 992723 or lubricant meeting requirements of NLGI 2 Category LB or GC LB SAE 75W 90 Synthetic Axle Lubricant Rear Axle GM Part No U S 89021677 in Canada 89021678 meeting GM Specification
471. you may not be able to start your vehicle When trying to start the vehicle if the engine does not start and the security light comes on there may be a problem with your immobilizer system Turn the ignition control knob off and try again 2 30 If the ignition control knob does not rotate and the keyless access transmitter appears to be undamaged try another keyless access transmitter Or you may try placing the transmitter in the transmitter pocket located in the center console See Electronic Key Not Detected under DIC Warnings and Messages on page 3 54 At this time you may also want to check the fuse See Fuses and Circuit Breakers on page 5 122 If the ignition control knob still does not rotate with the other transmitter your vehicle needs service If the ignition control knob does rotate the first transmitter may be faulty See your dealer retailer who can service the theft deterrent system and have a new keyless access transmitter programmed to the vehicle It is possible for the immobilizer system to learn new or replacement keyless access transmitters Up to 4 keyless access transmitters can be programmed for the vehicle To program additional transmitters see Matching transmitter s to Your Vehicle under Keyless Access System Operation on page 2 9 Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle Starting and Operating Your Vehicle New Vehicl
472. your body to be sure the seat is locked in place Power Seats If the vehicle has power seats the controls used to operate them are located on the outboard side of the seats e Move the seat forward or rearward by sliding the horizontal control forward or rearward e Raise or lower the front part of the seat cushion by moving the front of the horizontal control up or down e Raise or lower the rear part of the seat cushion by moving the rear of the horizontal control up or down e Raise or lower the entire seat by moving the entire horizontal control up or down The vertical control is used for reclining your seatback See Power Reclining Seatbacks under Reclining Seatbacks on page 1 8 for more information Power Lumbar Your vehicle may have this feature The driver s and passenger s seatback lumbar support can be adjusted by moving the control located on the outboard side of the seat cushions To increase or decrease support hold the control forward or rearward Keep in mind that as your seating position changes as it may during long trips so should the position of your lumbar support Adjust the seat as needed Heated and Ventilated Seats On vehicles with this feature the buttons are located on the climate control panel sf Heated Seat and Seatback Press for the heated seat and seatback Ventilated Seat Press for the ventilated seat A light bar in the climate control display sh
473. ystem will default to normal time delay operation if the Rainsensor detects something that would affect Rainsense operation When Rainsense is active the headlamps turn on automatically If it is dark they remain on See Wiper Activated Headlamps under Wiper Activated Headlamps on page 3 17 for more information Notice Do not place stickers or other items on the exterior glass surface directly in front of the moisture sensor Doing this could cause the moisture sensor to malfunction Windshield Washer A CAUTION In freezing weather do not use your washer until the windshield is warmed Otherwise the washer fluid can form ice on the windshield blocking your vision W Washer Fluid Press the button with this symbol located at the end of the windshield washer lever to wash the windshield The washer fluid sprays onto the windshield and the wipers run for a few cycles to clear the windshield Press and hold the button for more wash cycles Washer Fluid Low Add Fluid displays on the Driver Information Center DIC when the washer fluid is low See DIC Warnings and Messages on page 3 54 If the headlamps are on while the windshield is being washed the headlamp washers if the vehicle has them will also turn on See Headlamp Washer following for more information Heated Windshield Washer If your vehicle has the heated windshield washer fluid system it can be used to help clear ice snow tree sap

2008 Cadillac CTS Owner Manual

Contents

Download Pdf Manuals

Related Search

Related Contents