Molift AS - Meditec Medical
Contents
1. NOMAD CE a patient lifter from mi er oe e Ga akal fala molift designed for life molift NOMAD Innhold Rail SYStOIN 0c cccccccccececeeeecetseecenseeeeeseeees 17 TOMO coe reeset EE EEEE 17 General advice ccccccceceeeeeeeeeeteeeeeeees 3 Explanation Of symbols cccccceeeeceeeeeee es 3 Accessories 0000 0 ceccccccccceceeeeeeeeeeeeeeeeeeeeeans 18 Before using the patient lifter 604 3 Lifting SHING ccccccccceccceeccceececceceeesaneesaeeeaaess 18 FROSDONSIOWICY sornes 3 Sling Size ensisi deii 19 ODA e S 19 Safety precautions cc cece cece eens 4 Molift NOMAD 00000000000eeeeeeeeeeeeeenenees 19 CUA EEE E E E uote teunceauvoue 4 If defects or faultS OCCUL cccccseeeeeeeeeeees 4 Maintenance 20 Lift and transfef cc ccc cece cece cece eeeeeeeeeeeeees 4 Daily MA INTONANCE cccccceccc cece tees eeeee eens 20 Monthly maintenance c cccccccceeee sees eens 20 About the product 0 cece cc ceeeeeees 5 Troubleshooting 1 0 ccccccceeeeeeeeecceeceeseeeeeaes 20 Main Plt ccc ccc cccceccc cece eec eee eeeceeeaeeaeeeaeenees 5 Service maintenance 20 Safety AOVICES ccccccccecccceeccececeeseeeeseeesaees 5 NOOS er eE EE OEE EERE 21 Technical data 0 000 cc cceeeeeeeeeeeeeeees 6 Assembly disassembly 0000000 7 Assembly and us2. the low est capacity also applies for the lifter Molift AS has the system liability only when the rail system with trolley is mounted by authorized service representative dealer or Molift AS e Attach the safety hook on the lifting belt on the attachment arm Trolley Attachment arm Lifting belt Lifter Hook the attachment arm to the trolley molift designed for life molift NOMAD e Alternatively the lifting belt can be hooked di rectly onto the trolley e Connect the hand control unit to the lifter e Reset the emergency stop button Take care that the lifter do not get damaged by hitting the floor or walls Danger of per sonal injury if the lifting hooks are dam aged Checklist before use e Check that the lifter has no visible damage or missing parts e Check that the batteries are sufficiently charged e Make sure that the lifter is properly attached to the trolley and attachment arm and that the safe ty hook is locked e Check that the lifter functions correctly by run ning it up and down If any damage or faults occur on the lifter or the rail system contact your local serv ice representative dealer or Molift AS imme diately The lifter shall not to be used Disassembly e Lower the lifter enough to hold it e Untight the lifting belt and remove it from the trolley using the attachment arm or release the safety hook e The lifter can be moved The control electronic
3. 3032500 Art no 3033500 see the tables below size XXS and XS Molift Easy Toilet Sling Comfort headsupport Molift Easy Sling Molift Basic Sling a eee ie Molift Basic Bathing Sling No headsupport With headsupport Molift Ambulating Vest Art no 3023050 Art no 3024050 No headsupport Waist diameter Art no 3023000 Art no 3024000 Art no 303610 60 75 cm Art no 3023100 Art no 3024100 Art no 3036200 75 100 cm Art no 3036300 100 150 cm Page 1 8 of 24 E Rev E 09 2006 Sling size guide Easy and Basic Slings Color A B C code cm cm cm se efe o e f fe gt f 17 25 46 65 kaili a Choice of sling size depends on both user weight and shape size of user Q Please see the user manual following each sling for spesific user instructions Sling bag Bag for slings Art no 3048000 Molift NOMAD Attachment arm Art no 1211000 molift designed for life NOMAD Page 19 of 24 molift NOMAD Maintenance Daily maintenance Ee Detergents must be pH neutral Do not use solvents or strong liquids this may damage surfaces on the lifter For disinfection when needed use isopropyl alcohol Avoid abra sive cleaning products Clean surfaces with a damp cloth using an appropri ate detergent Monthly maintenance e Run the lifter through the complete installation and check that it is running smoothly e Verify that the hand control contact is firml
4. an incorrect manner and if e covers are removed by unauthorised personnel e used incorrectly e insufficient maintenance e load exceeds maximum limit The maximum load stated in this manual and on the lifter is the maximum load e unauthorised repair of electrical devices or cables Lift and transfer Several factors have to be considered during move ment of the lifter e the user shall sit as low as possible facing the di rection of movement e there is no obstacles in the moving area of the lifter Stand to the side of the user when lifting Ensure that arms and legs are clear of the chair bed etc Try to maintain eye contact with the user this will help the user feel safe and comfortable Pay close attention to your actions Ensure that all four loops of the sling are securely fastened to avoid the user slipping or falling Molift slings shall ONLY be used to lift per sons NEVER use the sling to lift and or move objects of any kind E Rev E 09 2006 About the product Molift NOMAD is a portable ceiling lifter intend ed for lifting and transferring persons The lifter is made out of light materials and has a battery It can be used in institutions with various needs mak ing it necessary to move the lifter between different rooms The lifter has intelligent electronics with soft start stop and a counter to register the number of lift cy cles Main parts The lifter consists of a chassis with motor lif
5. help placing the leg section O Lean the user forward gently but ensure you con tinue to support her Place the folded sling behind the user s back and push it down until it touches the seat of the chair The leg sections of the sling are pulled forward and beneath the user s thighs by the loops The loops are then crossed one through the other as shown molift designed for life Hook the loops on the lifting hooks A If the transfer is from a wheelchair the brakes must be locked to prevent the wheel chair from rolling away Raise lift user above seat height and perform the transfer It is not necessary to lift the person very high Lift and transfer to wheel chair Manoeuvre the lifter so that the user is as far back in the wheel chair as possible A When lowering you can use the following tech niques or a combination of them to position and get the user seated far beck in the chair If the transfer is to a wheelchair the brakes must be locked to prevent the wheelchair from rolling away e push gently on the knees e pull the loop on the back of the sling e tilt the chair slightly backwards Lower the user into the chair unhook the sling from suspension and remove the lifter Page 13 of 24 molift NOMAD Removal of sling Gently pull leg section to the side out from the us er s thighs Standing by the side of user lean her for ward supporting with one hand Pull sling
6. to its intentions The extended warranty is valid for a period of 5 five years starting at the date of purchase limited to 3 months after the production year week The extended warranty is offered in addition to the local sale of goods act It is mandatory that the product undergoes safety control and maintenance performed by an authorised service partner at least every 12 months according to this service manual made by Molift AS e Yearly maintenance and safety control must be performed within a maximum interval of 12 months and for the first time maximum 12 months after date of purchase or maximum 15 months after year week of production e Molift AS will cover the cost of spare parts and labour in the warranty period for all necessary re pairs caused by product defects that can be traced back to manufacturing The repair must be perfor med by an authorised service partner or at Molift AS own workshop during the warranty period e All warranty repairs must be approved by your Molift supplier or by Molift AS prior to the repair e The owner of the product is responsible for establishing the service agreement and the cost for the annual safety control and maintenance e The service manual has one page for every 12 months containing checkpoints for maintenance and safety control The extended warranty is valid only with signature and or stamp by authorised service partner including service partner s signed label with authorisation no on pro
7. until it is possible to attach the climbing belt on the opposite trolley to the lifters handle Page 16 of 24 E Rev E 09 2006 molift NOMAD Rail system Another trolley with a rotatable attachment hook The rail system is mounted rigidly and may consist is also available This makes it easier to rotate and of several parts like a traverse with transition cou keep the patient in correct position pling and switches If any damage or faults occur on the rail system contact your local service representative dealer or Molift AS immediately Only one lifter is allowed to be mounted on each rail system at the same time Make sure that the rail system has the same max load as the lifter 230 kg If the molift NOMAD is mounted on a rail system with a lower lifting capacity the low est capacity also applies for the lifter Trolley The lifter is attached to the rail system by hooking the lifting belt on a trolley mounted on the rail sys A climbing belt on the trolley makes it possible to climb between two different rail systems molift Page 17 of 24 designed for life molift NOMAD Accessories Molift Easy Toilet Sling ee Sung Sune Molift Easy Paediatric Sling No headsupport With headsupport Art no 3032200 Art no 3033200 Art no 3005050 Art no 3006050 Rio soseson Gana acss0d Art no 3005000 Art no 3006000 ta aa hte ccea ace Easy Toilet Sling and Basic Bathing Sling for kids Art no
8. Before using a patient lifter the operator must be trained accordingly Practice lifting a colleague and be lifted by others It is important not only to know how to move another person using the lifter but also how it is to be lifted Try out and practice using all the relevant slings for the different types of lifter and movement you may encounter Before lifting a per son you should explain the procedure When using the lifter it s also important to use the correct sling and accessories according to e type of disability e size e weight e type of movement molift designed for life molift NOMAD Responsibility Please read these operating instructions carefully before putting the product into operation We as sume no liability for damage or malfunctions re sulting from failure to comply with the instruc tions Warranty claims must be made immediately on detecting the defect Remember to quote the se rial number Consumable parts are not subject to the watranty All technical information data and instructions for operation contained in these operating instructions were up to date at time of print and are compiled on the basis of our experience and to the best of our knowledge We reserve the right to incorporate tech nical modifications within the scope of further de velopment of the product described in this manual No claims can be derived from the information il lustrations or descriptions contained in th
9. ations avoiding putting your own back at risk without being completely exhausted after work and still have some sur plus energy when the workday is over This is the insight that drives us at Molift The company was started 20 years ago by a man who through his own experience saw the need for lifting and moving patients in an effective and comfortable way for both patient and carer We have since then delivered products that compliment the natural movements of the body that is both simple and intuitive to use Products designed to give the patient a better life in addition to providing the carer with real support and optimum work enjoyment This is the true meaning of Molift designed for life Molift AS Ole Deviksvei 44 N 0668 OSLO Norway Telephone 47 4000 1004 Fax 47 4000 1008 www molift com info molift com
10. bility and possible injury to personnel Page 10 of 24 a Fold the sling as indicated above before use The grey side should be facing away from the user when putting the sling in place The sling should be held by one hand leaving the other free to move and sup port the user Torn cut frayed or broken slings can fail resulting in serious injury to the user Use slings in good condition only Destroy and discard old unusable slings Sling without head support E Rev E 09 2006 NOMAD Lift and movement to and from bed Lift from bed Roll user onto her side Put the folded sling behind her back The centre of the sling should be parallel with the users spine Roll her then onto her back cP If the user has a bed which enables raising and lowering it should be lowered before the lifting starts Position the lifter above the patient Be careful not to lower the lifter too low touching the patient Make sure that the lifter is centred over the patient before Pull the leg loops forward and under the thighs as you start the lifting shown molift Page 11 of 24 designed for life When all four loops are hooked on the lifter raise the user carefully Make sure that the sling is properly hooked on the lifting hooks before you start lifting Oo If the user is in a hospital bed it will help to raise the head of the bed Repositioning of the user may be needed to ensure that a safe and comfortabl
11. duct Normal warranty is 12 months This still applies for slings hand control batteries and paint Gjovik 28 08 2006 Molift AS Geir Olav Farstad Managing Director Page 22 of 24 E Rev E 09 2006 NOMAD molift DECLARATION OF CONFORMITY C Molift AS Ole Deviksvei 44 0668 OSLO NORWAY Telephone 47 40 00 10 04 hereby declare that Molift NOMAD patient lifter and that the accessoires used only together with this product Year 2006 are in conformity with e The Council Directive concerning medical devices 93 42 E F and according to this classified as medical equipment class 1 Molift NOMAD is manufactured in conformity with the following national or international standards that also might implement a harmonised standard e 15010535 Hoists for the transfer of disabled persons Requirements and test methods e ISO 14971 Medical equipment Risik analysis Notified fody Hjelpemiddelinstituttet NEMKO AS Gregersensvej Gaustadalleen 30 DK 2630 Taastrup N 0314 OSLO Denmark Norway Tel 45 43993322 Tel 47 22960342 Title Managing Director Name Geir Olav Farstad Company Molift AS 28 08 2006 AAN C mi ee a e are aeaee molift Page 23 of 24 designed for life At times with increasing demand for efficiency in the healthcare sector and growing focus on patients needs it is easy to neglect the needs of the carer The need to give better help and caring avoiding heavy lifting situ
12. e Of Charge 00c00006 T ASSO osre EE 7 IMPORTANT Checklist before USC ccccccceecceeeeceeeeeaees 7 Disassembly scxsronctnduracepaiaendacaseumcsactndeaasiedmees 7 The patient lifter is only meant to be used by qualified personnel Operation castetenteanctecanar atnansin at coecumanraneromientinte 8 FUNCTIONS cccccccecscccsseecenseeeesseeeesseeceneeenaes 8 The manual shall not be handed over or made Operating the liftet 8 available to any unauthorised third party wit Emergency stop and emergency lowering 8 hout a prior written consent from Molift AS Battery Cafe nnn 8 Exciting laws conventions and agreements 071721101101 MONDIN 9 protects all documents No extract of this do Electrical system ccccccceeecceceeeeeeeeeeeeeeeaes 9 cumentation can be reproduced used or trans Lift and transfet oieee 10 Jerred without prior written consent from Molift Using lifting SINGS oos aooanonnaeneanaeneeneaeeaaan 10 AS Violation of these regulations may lead to Sling without head support 0 000086 10 judicial repercussions and economic responsi Sling with head support ceeeeeeeee eee 10 bility Industrial rights are reserved Lift and movement to and from bed 11 Ly i Lift from bed cc ccc ecceceec eee eeeeeeeeeeeeeeeeeees 11 molift Transfer 10060 hovcnteinucecetsesenaterdaveaseseiuate 12 Removing the SIiINg cceceeeeeeeeeeeees 12 Lift and transfer to and from fl
13. e sitting position 1s at tained as the user is raised Reposition using the handle on the back of the sling Raise the user until the buttocks are just above the mattress Lift the user s legs and turn her so she fac es the direction of movement Move the lifter away from the bed Page 12 of 24 Transfer to bed Centre the user over the bed and turn her so that the feet point to the foot end of the bed Lower the user carefully Remove the loops from the lifter hooks Removing the sling Gently pull leg section to the side out from the us er s thighs and towards yourself Pull the shoulder section under the neck of the user and roll her gently onto her side Pull the sling away and roll her onto her back Be careful when rolling the user onto her side Make sure you have control over the movement to prevent her from rolling com pletely over and out of the bed Lift and transfer to and from floor Lift and transfer to and from floor is almost identi cal to lift and transfer from bed Please see the sec tion above E Rev E 09 2006 Lift and transfer to and from wheel chair Lift and transfer from wheel chair Fold the sling as described in Using lifting slings Turn the gray side of the sling away from the user when placing the sling If the users physique and ability allows it the user should be encouraged to take active part in fitting the sling The user can lean forward lift her thighs and
14. emergency low ering button The lifter will make a smoothly movement downwards e If the lifter don t move charge the battery and try the emergency lowering button again Do not run the lifter when connected to the charger If none of the actions above works the user must be lowered manually Call for assistance If the reason for failure causing an emergen cy lowering is unknown or if it is a result of failed component contact your local service representative dealer or Molift AS Battery care The batteries of the Molift NOMAD 1s a 26 4 V cell unit that is placed inside the chassis Molift NO MAD can be used with two kinds of batteries NiCd and NiMH The lifter has a battery light on both the lifter and the hand control which illuminates when the battery voltage drops below a certain level There will also be an audible alarm which indicates that the bat tery needs charging There is still enough capacity to lower the patient E Rev E 09 2006 If the battery is discharged during a lift it is always enough power to lower the user down again O Charging The charger is to be mounted on the wall and con nected to the power outlet at all times The charging light on the charger gives a yellow light when the charger is ready for use and there is no hand control unit placed in the charger Charging light Mode Ready for use no bat tery connected Trickle charge Orange green Place the hand control i
15. eneral precautions must be read understood and followed carefully Any disregard to these precautions may result in personnel injury or damage to the equipment The lifter must be taken out of service immediately or not returned to serv ice if faults and or irregularities that may have in fluence on the safety are discovered Safety devices and equipment must not be removed disabled or in any other way altered A Molift NO MAD shall only be used when all safety devices and equipment is in place and fully operational The lifter is designed for indoor use only and should not be exposed to sun for a longer pe riod The lifter is designed for use in room tem perature 10 to 40 C This should be taken into consideration when transporting the lifter and therefore keeping it in a tem perate part of the vehicle Alternatively the lifter must rest in a temperate room until the equipment has achieved proper working tem perature Page 4 of 24 If defects or faults occur The lifter must be switched off immediately if one of the following conditions occur e damage to electrical devices or cables or damage to parts of electrical insulation e damage or failure on safety devices If the lifting movement does not start when the corresponding button is pressed please consult the troubleshooting table in the maintenance chapter to locate the fault O Injury to personnel or equipment may occur if Molift NOMAD 1s used in
16. erheating The electrical system has a power save function which will turn off the electrical system after ten mi nutes without activity All lights will turn off The system is activated when pushing one of the opera ting buttons Red sound If the lifter is run up and down constantly for a long er period the electronics may be overheated and then the lifter will stop The service diode will give a yellow flashing signal until the lifter has cooled down sufficiently to work again If the lifting belt is untight the lifter will stop to avoid the belt from rolling in incorrectly Run lifter up to tighten belt If you are not able to solve the fault or problems by yourself using this manual please contact your local authorized service representative If you don t know whom to contact locally please contact your dealer or Molift AS to get help Service is done according to procedures in the serv ice manual included with the lifter and the service signal on the lifter The owner is responsible to ensure proper logging and written verification performed by authorized service representative The service manual has dedi cated pages for logging and signature E Rev E 09 2006 Troubleshooting Symptom Possible cause action The lifter does Battery discharged charge not work battery Emergency stop is activated pushed in turn clockwise to reset The cable contact of the hand control has disconnected re con
17. ese in structions We assume no liability for any damage or malfunction caused by operating errors non com pliance with these operating instructions or inappro priate maintenance We expressly point out that only genuine Molift AS spare parts and accessories ap proved by us may be used For safety reasons the fitting and use of spare parts or accessories which have not been approved and unauthorised modifi cation or conversion of the product are not permit ted Molift AS will accept no liability for damages resulting from such acts With the exclusion of product liability Molift AS is liable for faults or omissions on its part within the scope of the warranty obligations stated in the purchase contract Claims for damages are exclud ed irrespective of the legal reason from which such claims are derived Only documentation belonging to the actual equipment is valid Any failure to comply with the safety regulations and precautionary measures stated in these operat ing instructions renders the declaration of conform ity supplied with the system in accordance with Council Directive 93 42 EEC concerning medical devices invalid Page 3 of 24 molift NOMAD Safety precautions General Before putting a Molift NOMAD into operation the operator must ensure that the lifter and accessories are in good working order especially with regards to safety All instruction and information in this manual re garding safety and g
18. has a power saving feature which puts the system into stand by after a while of no activity Activate one but ton and the service lamp will give a green light to show that the lifter is ready for use If the lifter is to be stored for a longer period activate the emergency stop O Page 7 of 24 molift NOMAD Operation Functions Emergency lowering Battery light Emergency ua i stop gt 6 The i gt PA i s a ir oN U Q A p LA t ka Down Service light Hand control Battery light Charger Hand control Charging light Page 8 of 24 Operating the lifter Connect the hand control cable to the plug on the back side of the lifter The hand control has two but tons which gives the operator excellent control of the movement of the lifter up and down Two but tons with the same function are placed on the right front side of the lifter Emergency stop and emergency lowering All Molift lifters are equipped with emergency stop and lowering The emergency stop button will cut the power to the motor and is situated on the left front side of the chassis Turn the button clockwise to reset It is possible to perform an emergency lowering in case of an electronic malfunction or uncontrolled stop There is an emergency lowering button on the left front side of the chassis with a yellow seal Move the lifter to a suitable location to lower the user e Puncture the seal and press the
19. n the charger After a few seconds the charger light will change from yellow to orange indicating that the battery 1s charging If the charging light gives a constant green light this means the batteries are fully charged The lifter can not be used while charging the batteries Its not possible to overcharge the batteries but to ensure optimal performance through out the lifetime of the battery we recommend that the battery is allowed to rest for a couple of minutes after charging O The lifter can be operated without hand control The lifter is then equipped with a special charger with a contact to be plugged in the hand control contact on the lifter when charging Both chargers have the same functions molift designed for life molift NOMAD Electrical system On the front right side of the lifter there 1s a service light which will give a signal when the lifter needs service When there is a green light the lifter can be used normally If there is no light push one of the up down buttons to activate the electronics and the service lamp will illuminate 2 Battery light Service light The electrical system has a power save function which will turn off the electrical system after ten mi nutes without activity All lights will turn off The system is activated when pushing one of the opera ting buttons If the lifter is run up and down constantly for a long er period the electronics may be o
20. nect contact Hand control has failed use operating buttons on lifter switch hand control or contact local service representative for service Lifting belt is untight tighten lifting belt raise lifter Defective control electronics contact local service repre sentative for service Lifter is defective contact lo cal service representative for service Lifter moves Brakes defective contact lo slowly or makes cal Service representative for noise service molift designed for life NOMAD Page 21 of 24 molift NOMAD molift WARRANTY Molift AS hereby declares that this product is awarded up to 5 five year extended manufacturer s warranty It is very important to our customers and to Molift AS that our products meet all relevant quality and sa fety requirements according to both customer and authority demands Molift AS develops and manufac tures products with high standards of safety quality and design and we are continuously in a process of keeping our products in position among the market leaders To make our products quality level more explicit Molift AS have introduced extended warranty time on all of our patient lifters A 5 five year warranty against defects which might be traced back to ma nufacturing is offered The extended warranty period is offered under the condition that the regulations described here are completely fulfilled and that the product has been used according
21. ng and an audible signal will sound The lifter features emergency stop and emergen cy lowering Rail Safety hook Lifting belt SS Chassis Buttons for lifting and oN lowering Battery light and service light A Page 5 of 24 molift NOMAD Technical data Weight total 6 8 kg Material Fibre armoured plastic and aluminium Motor 24 VDC Battery 26 6 V NiCd 1 9 Ah or 26 4 V NiMH 2 2 Ah 200 Page 6 of 24 Lifting capacity maximum 230 kg 500 Ibs Lifting height 2 meters Number of lifts with fully charged battery approx 60 standard lifts 75 kg 50 cm Measurements 522 x 200 x 329 mm LxBxH Measurements in illustrations below are in millime tres 0 2000 mm 160 mm 330 mm E Rev E 09 2006 Assembly disassembly To be able to operate the Molift NOMAD the opera tor must have good knowledge of the lift including assembly and preparation before use Assembly and use of charger The battery charger shall be mounted on a vertical wall surface close to a power outlet The charger shall be connected to the power outlet at all times Molift AS tests and charges all batteries be fore packing and shipment However all bat teries must be charged before use Assembly The lifter shall only be mounted on a rail sys tem with a capacity on 230 kg or higher If the molift NOMAD is mounted on a rail system with a lower lifting capacity
22. oor 12 d esi gne d for life Lift and transfer to and from wheel chair 13 P and transfer from eeclenall ee 13 Molift AS ift and transfer to wheel chair 13 l Removal of Sling cceccecceeceeeeeeeeeeees 14 a Bath occccccscsssssecsssssesssseessssesssseessseeesssesees iA ey Toileting 14 Teleph 47 40001004 www molift com HERING esses seeeesse tees nieeeeeeieteeesneiittetie Fax 47 40001008 imo con TT OW a EE E E E E E E E 16 Page 2 of 24 E Rev E 09 2006 General advice This user manual contains important safety instruc tions and information regarding the use of the lifter Carefully read the manual before using the lifter in order to be familiar in the function and use of the lifter Explanation of symbols This symbol is used to point out instructions and information related to work place safety where injury may occur if the information is disregarded or ignored Follow these instruc tions be careful and attentive at all times This symbol indicates important information regarding the use of the equipment If not taken into consideration it may lead to dam age or functional defects to the lifter or other equipment This symbol indicates important and useful information If taken into consideration it will help the operator of the lifter to work ef ficiently It may help simplify routines and to explain complicated facts O Before using the patient lifter
23. t Easy Toilet Comfort place the leg sec tion over and down between the thighs and pull outwards from the inner part of the thighs o The leg sections of Molift Easy Toilet Comfort Sling are fitted to separate the legs therefore they should not be crossed as the other Easy slings Hook the four loops on the suspension as for oth er slings Position the lifter around the toilet and lower the user Pull the leg sections out of the way The sling can be left on during bathroom use Alternative Q By pulling the leg sections from the outside and in you will achieve a wider leg posi tion molift designed for life NOMAD Page 15 of 24 molift NOMAD Climbing With Molift NOMAD it is possible to climb be tween two rail systems and then we can avoid cut outs above the doors There must be a trolley with a climbing belt present on both rail systems e Lower the lifter until it hangs in the climbing belt only The lifter will stop if the lifting belt is un Trolley Rail Climbing belt e Move the lifter until it stops at the end of the rail and move the trolley on the opposite side as close as possible e Move the lifting belt to the opposite trolley with the attachment arm e Run the lifter up until it hangs in the lifting belt The climbing belt can be released and the lifter can be run up and down as normal Climbing belt Lifting belt Handle e Raise the lifter
24. ting belt electronics and battery A rail system with a trolley is necessary for attachment of the lifter The lifter has four hooks for attaching the sling with the user The lifter can be attached to the trolley directly or by using an attachment arm This makes it easy to move between the different rail systems A climbing strap on the trolley makes it possible to climb from one rail system to another with a user suspended Trolley Lifting handle Emergency lowering Emergency stop Lifting hooks molift designed for life molift NOMAD Safety devices Molift NOMAD is equipped with several safety de vices which are intended to prevent personal inju ry or damage to equipment in the case of incorrect use e The lifter has an overload sensor which prevents the lifter from lifting too much If the weight of the patient is too high the lifter will stop The lifting hooks are designed to prevent the lift ing sling from falling off Electrical system has a protection against over heating If the temperature on the circuit card 1s too high the lifter will stop and you will have to wait until the temperature goes down The lifter has a sensor which will stop the lifter if the lifting belt is not tight to avoid it curling up e The electrical system registers the lifters operat ing time and gives a signal when service is re quired e The battery lamp will illuminate when the lifter needs chargi
25. up from behind her back Pulling sharply on sling may cause user to fall forward resulting an injury Always sup port the user by keeping one arm around the user s Shoulder when fitting or removing the sling see illustration If the users physique and ability allows it the user should be encouraged to take active part in fitting the sling The user can lean forward lift her tights and help placing the leg section O Bath The procedure for lifting to from the bath is in prin ciple the same as for to from bed or to from chair A special bathing sling is used for this purpose This sling dries quickly and may be washed at 80 C Take care that the lifter itself is NOT lowered into the water The lifter might stop function ing Page 14 of 24 Toileting The Molift Easy Toilet Sling is used with the stand ard 4 point suspensions Molift Easy Toilet sling is a toilet sling with a thicker and wider upholstery It is also avail able with head support The Molift Easy Toi let Comfort sling is easier to fit in narrow en vironments and is available with a separate head support The toilet sling can be washed at 80 C and is fitted as follows e Insert the sling behind the users back with the grey side away from user e Fasten the belt firmly around the user s body e Place the leg section under the front part of the thighs and pull the loops up between the thighs E Rev E 09 2006 e On Molif
26. verheated and then the lifter will stop The service diode will give a yellow flashing signal until the lifter has cooled down sufficiently to work again If the lifting belt is untight the lifter will stop to avoid the belt from rolling in incorrectly Run lifter up to tighten belt Page 9 of 24 molift NOMAD Lift and transfer The suspension shall always be positioned across the user as shown left in the illustration below ome When using slings intended for two point sus pension the suspension shall be used diago nally i e loops from the sling shall be fas tened on hooks diagonally opposite Be careful during movement the suspended user may swing somewhat during turns stops and starts Be particularly careful when manoeuvring close to furniture to prevent the suspended user from collid ing with these objects It is preferred to turn the user to face the moving direction Check that the lifting belt dont curl when raising The lifter is only to be used for transferring over short distances It is not a replacement for wheelchairs or similar Using lifting slings The Easy lifting slings are as the name indicates easy to use They are washable at 80 C and auto clave at 85 C for 30 minutes The plastic insert of the head support should be removed before wash ing It is recommended to use Molift Easy slings Slings from other manufacturers may have other specifications leading to unexpected insta
27. y in place Clean contact and hand control with white spirit to remove grease and dirt e Check that the hand control cable has no dam age e Check that the lifting belt has no damage re move hair dirt and dust from opening and check that the belt moves out and in easily throughout the length of the belt e Run lifter up and down to verify that it moves normally without any abnormal noise e Check that the battery and service light gives no signal Contact local service representative dealer or Molift AS if the lifter does not work properly or if the serv ice light illuminates Service maintenance On the front right side of the lifter there is a service light which will give a signal when the lifter needs service When there is a green light the lifter can be used normally If there is no light push one of the up down buttons to activate the electronics and the service lamp will illuminate Service light Page 20 of 24 The electronics measures the operating time of the lifter and after a specific time the yellow light will illuminate indicating that the lifter needs service Take contact with your local Molift service repre sentative dealer The lifter can still be operated but after a while an audible alarm will sound to remind the operator that the lifter needs service immediate ly Service light codes Servicelignt Mode Red Perform service Perform service im mediately Flashing yellow Ov
Download Pdf Manuals
Related Search