User`s Manual - Glunz & Jensen
Contents
1. Part 3 Cleaning and Maintenance General 1 The Conveyor Belt Drive Chain should be lightly lubricated with SAE 20 50 Oil and the tension checked and re set if required every 6 12 months 2 The Conveyor Belt Tension should be checked and re set if required every 6 12 months 3 All of the bearings are sealed and require no maintenance The Oven is fitted with an over temperature protection device that is factory set to prevent the temperature from rising above approximately 200 C This unit will override a higher setting entered into the switch plate mounted temperature controller In the event that the temperature rises above this over temperature setting the heating system will automatically switch off and an intermittent audible alarm will sound This will indicate a fault with the heating or temperature control systems within the oven An electrical engineer should therefore examine the machine and rectify any fault before continuing Note that the alarm will continue to sound until the temperature has fallen such that the heating system can again be turned on Cleaning I Cleaning components with anything other than a mild detergent or a recommended cleaning agent may cause irreversible damage and invalidate any watranty I Never use hard tools or abrasive materials when cleaning any part of the equipment Always unplug the unit from the power outlet or the mains supply before carrying out any cleaning or mainten2. User s Manual Quartz Supreme Postbake Oven 85 125 User s Manual Quartz Supreme Postbake Oven 85 125 2007 Glunz amp Jensen A S All rights reserved User s Manual Quartz Supreme Postbake Ovens 85 125 Part no 51560 rev AA April 2007 The information in this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Glunz amp Jensen A S Glunz amp Jensen A S assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual Glunz amp Jensen A S assumes no responsibility or liability for loss or damage incurred during or as a result of using Glunz amp Jensen products Printed in Denmark User s Manual Quartz Supreme Postbake Oven 85 125 Table of Contents pa Table of Contents Part 1 Introduction 0 000 000000 ee 1 1 EGOSI WIS MANUA sau eee Sg eed enh bese cee et eee s ose EE ake ee os 1 1 Intended use of this EUS l 1 UE ieena E ee needed eee een E E E E eases l 1 Reservations ertzik Gi e e gt Gr Ze e eie e de Gi e Ra Ea d Eg gg d b gg ee e l 1 Jaiei riaz 1 1 POOIOVEIS wade eaed eeu an saat oe Ga ees oe ee a eie e GT d ee eee 1 1 Intended use of THE equipment agert Eze gg Gre EEE Ee EE EEEk b a EE 1 1 MOLONS face cei uw she ncaa E dig GE Ele E E e eens bees ee ee d Ea 1 2 EEE Dalat 2444454246446 4 dg ei a Ge b
3. ance procedures etc Daily Wipe the machine with a damp cloth to remove dust pay particular attention to the input area of the machine Never touch the top of the oven after it has been operated as the temperature exceeds 40 C User s Manual Quartz Supreme Postbake Oven 85 125 0716 ge Cleaning and Maintenance Cleaning 0716 User s Manual Quartz Supreme Postbake Oven 85 125
4. emperature adjustment The oven is fitted with a temperature controller on the control panel located on the Electrical Enclosure To adjust the plate surface temperature 1 Press the button marked x and hold down The unit will display the pre set temperature 2 To increase the plate temperature press the button marked A until the required temperature is indicated on the display 3 To decrease the plate temperature press the button marked W until the required temperature is indicated on the display 4 Release the button marked x The unit will then display the current oven temperature Time should be allowed for the oven to reach the new oven setting as indicated on the Control Unit before processing the plates When a plate enters the oven the temperature indicated on the display will fall by approximately 2 C or 4 F and will then recover to the pre set temperature within a short time This is normal and has no effect on the final plate temperature User s Manual Quartz Supreme Postbake Oven 85 125 Operating Procedures Sa Transport conveyor speed adjustment Transport conveyor speed adjustment This adjustment should be carried out by a service technician only User s Manual Quartz Supreme Postbake Oven 85 125 0716 Sa Operating Procedures Transport conveyor speed adjustment 0716 User s Manual Quartz Supreme Postbake Oven 85 125 Cleaning and Maintenance EB General
5. icians who are trained in servicing the equipment e The installation procedure is described in Installation in Section 2 of the Service Manual e The manufacturer cannot be held responsible for any damage caused by incorrect installation of this oven Technical Data e Observe technical data from the oven name plate located on the base of the oven Notes Cautions and Warnings Throughout the manual notes cautions and warnings are indicated with various icons and written in bold like the example below I Never use hard tools or abrasive materials when cleaning any part of the equipment Explanation The operator should observe and or act according to the information in order to obtain the best possible function of the equipment D The operator must observe and or act according to the information in order to avoid any mechanical or electrical damage to the equipment The operator must observe and or act according to the information in order to avoid personal injury User s Manual Quartz Supreme Postbake Oven 85 125 Introduction a Functional Description Functional Description General The Quartz Supreme Postbake Oven is designed to deliver precise and uniform postbaking of thermal plates ensuring consistently high processing quality At one of four preselected conveyor speeds the plates are run through the oven The balanced air flow ensures an exceptional heating uniformity across the plate
6. o eee dz 1 2 Notes Cautions and Warnings 0 0 0 0 a ee 1 2 EXDIGN GUO sa a oe ome betze bt ge Gg Geiger Ed gre b rt ewe ie eee tes 1 2 Functional Description 644 4 0 604 620000808 S9e marks oh aeeeul ee eee ew es 1 3 GONG dle gas ee E EE ee E bie ee eee he e e et ee ee eee ee ee 1 3 Part 2 Operating Procedures AAA 2l Oven control panel easi eers csar ee gb sa ba Zerra EA pea E E GE e err b Ea 2 1 GND DVOCCUUIC e an wt ae cae eee hee ae ee ba ae ee E a d E E Zea 2 1 Turning the Postbake Oven to sleep mode 1 es 2 1 Complete SNUTGOWT zs ices ck na eae heed end een ee oh ee ee 2 2 Temperature adjustment its weit ed ewe ee we On ke ee ee we a we ha 2 2 Transport conveyor speed adjustment AAA 2 3 Part 3 Cleaning and Munt AAA 3 1 BEREK eg e dt be EE e d Be EEE e EE e St ee d EEE EE b Eg hee eee d tg 3 1 Cleaning e eos oe Gi e Sr oes eae ege Ee Gr whe hee ese ne erg ed ggb ees 3 1 Dall s e2n aaa see eek eee eee ye eRe eee eee eee eee ees eee Gee 3 1 User s Manual Quartz Supreme Postbake Oven 85 125 0716 0716 User s Manual Quartz Supreme Postbake Oven 85 125 Introduction GD About this manual Part 1 Introduction About this manual Intended use of this manual e This manual is for the daily user of the equipment Always read the Safety Instruction Manual part No 21741 before starting up the equipment and keep it with the machine for reference at all times Illustrations e As this manual co
7. vers a complete range of ovens the illustrations may not fully reflect your present oven Reservations e This manual was written and illustrated using the best possible information available at the time of publication e Any differences between this manual and the equipment reflect improvements introduced after the publication of the manual e Changes technical inaccuracies and typographical errors will be corrected in subsequent editions e Asa part of our policy of continuous improvement we reserve the right to alter design and specifications without prior notice Important Approvals e The oven is manufactured according to legal demands For compliance with the requirements the equipment is tested by Underwriters Laboratories or other accredited authority Approvals will appear on the labels attached to the equipment s name plate located on the base frame of the oven Intended use of the equipment e Development of photographic materials as specified in Technical specifications in Section 1 of the Service Manual User s Manual Quartz Supreme Postbake Oven 85 125 0716 ie Introduction Notes Cautions and Warnings Installation e It is the responsibility of the owner and operator s of this oven that the installation is made in accordance with local regulations and by engineers authorized to carry out electrical installations e Installation service and repair must be performed only by service techn
8. within Zika User s Manual Quartz Supreme Postbake Oven 85 125 0716 ta Introduction Functional Description 0716 User s Manual Quartz Supreme Postbake Oven 85 125 Operating Procedures SA Oven control panel Part 2 Operating Procedures Oven control panel 1 Turn on the power supply with the mains switch The green LED H1 will light 2 Press the standby key 3 The oven starts with the last active program H2 is on until the set point has been reached H4 or H5 or H6 or H7 is on 4 Select the desired program by pressing one of the P keys or Shutdown procedure Turning the Postbake Oven to sleep mode e Press the standby key LED H3 starts flashing to indicate the off cycle has started When the oven has cooled down to lt 80 C the unit will enter sleep mode User s Manual Quartz Supreme Postbake Oven 85 125 0716 ze Operating Procedures Complete shutdown Complete shutdown The oven should only be shut down completely for holidays or for maintenance and servicing purposes 1 Wait until the oven has gone into sleep mode below 80 C 2 Shut down the oven by switching the mains switch located on the left hand side of the Electrical Enclosure to OFF The oven unit should only be switched off from the control panel DO NOT turn off the fan or isolate the machine from the mains supply before the shutdown sequence is completed as damage may occur T
Download Pdf Manuals
Related Search