GENUINE PARTS INSTALLATION INSTRUCTIONS CAUTION
Contents
1. Fig 332 Accessory Service Vehicle Connector 44 amp Harness Foam taped connectors Vehicle lt __ Harness EC Mirror 38 Route the Accessory Service Connector up behind the main body harness to the accessory connector plug Plug the connectors together Fig 33 Note Be sure the new harness routing does NOT interfere with the emergency brake in any way 39 Wrap the connectors with 1 piece of foam tape and position them along side the main body harness Fig 34 40 Route any extra wire along the existing harness and bundle the EC mirror harness to the main body harness with a wire tie Fig 35 Page 13 of 19 999L1 G2000II Rev 7 18 14 ACCESSORY CHECK Note If errors are encountered during testing and compass calibration see diagnostic flow charts pages 16 18 Tighten negative battery terminal nut to 5 4 Nm 47 8 in Ib With ignition switch OFF push each Homelink button one at a time and verify that the LED indicator to the left of the center switch illuminates with a red LED Fig 37 Turn the ignition switch to ON Ensure vehicle is in well lit area Check to see that the green LED is illuminated If it is not press the B button to turn it on Cover the forward looking photocell located to the driver side of the wire harness connection on the back of the mirror with a dark cloth or towel After a few seconds the mirror should begin to darke2. L Check all vehicle electrical systems that the accessory interfaces with Power mirror switch Traction control switch Hood Release Fuel Door Release RE INSTALLATION OF REMOVED PARTS A CAUTION Use caution when re installing interior components to avoid damage scratches or breaking of mounting clips Refer to the vehicle service manual for more information C LH front pillar garnish L Insert new clip P N 76988 3DNOA into garnish hole ensuring long hook faces down Fig 39 Fig 39 Long Hook Faces Down L Insert base of finisher Insert panel removal tool between front pillar garnish bottom side and body side and press clips into body Push garnish toward vehicle body to attach FINAL INSPECTION Verify re installed trim parts for proper flush fit no gap no waviness etc Verify all clips are fully engaged and locked Verify re installed trim parts are free from cracks scratches or stress cracks Verify vehicle headliner seat steering wheel center console floor carpets etc are not soiled Verify interior and exterior is not damaged Turn ignition switch to ON and confirm proper operation of Vehicle Systems If equipped verify all window and sunroof one touch operation and perform the reset procedure if necessary Refer to the vehicle service manual for more details Confirm proper audio function AM FM SAT CD and AUX Re program radio presets and other vehicle setti
3. HomeLink com 3 Contact HomeLink Customer Service hotline 1 800 355 3515 Customer must at a mi um contact the HomeLink Customer Service hotline for help with programming before returning EC mirror as defective 999L1 G2000II Rev 7 18 14 DIAGNOSTIC FLOW CHART EC MIRROR KIT DRIVER SIDE ACCY_SER_CONN CONNECTOR BAT 2 TAIL LAMP apre RooM LAMP 4 Ein y BAT SAVER s M d FRODOR SW RH e LS LL Lung C NR neuserspamuc E acoum o u a RR DOOR LH vendu a 252 5 8 8 9 to 11 12 Note Pin location is referenced looking into wire side of connector EC MIRROR Legend Posi tap J Page 19 of 19 999L1 G2000II Rev 7 18 14
4. green LED illuminated on EC mirror Is green LED illuminated 12V being delivered to EC mirror ENSURE 1 EC harness power wire is securely plugged into blue wire of junction block connector 2 Check fuse corresponding to connection point of junction block to see if it needs to be replaced 3 EC harness ground wire is securely attached to vehicle grounding point 12V being delivered to EC mirror Orderservice part 999L1 VZ002 remove existing EC mirror wiring and replace with new Press each e button Each HomeLink i Ree button illuminates red illuminates LED when pressed Orderservice part 999L1 VZ000 Mirror remove existing receiving 12V EC mirror and replace with new A ENSURE 1 EC harness power wire is securely plugged into wire splice Posi tap connectoron vehicle 12V wire 2 ECharness ground wire is securely attached to vehicle gounding point Mirror receiving 12V HomeLink and the HomeLink house are registered trademarks of Gentex Corporation Page 18 of 19 Customermustnow attempt to program HomeLink This usually cannotbe completed atthe Dealership because many remote controlled devices utilize rolling code Did customer n successfully Mirror is functioning program properly HomeLink Did customer 1 Attemptto follow programming instructions User Guide in vehicle glovebox 2 Visit www
5. switch pulled up and BCM in transit mode Failure to confirm the vehicle has been removed from this state will result in loss of normal vehicle operation The confirmation requires two checks 2a Locate the exended storage switch in the 2B To remove transit mode by doing as follows cabin fuse block Once located check that 1 Remove fuse cover lid it is in the customer position See below 2 Push down shorting pin for reference 3 Ign on 2 times without turn the vehicle on Inventory Customer To put transit mode back is by doing as follows PULL UP PULL DOWN Lf Remove fuse cover lid Pull up shorting pin Assemble fuse cover lid Ign On 2 times without turn the vehicle on Confirm transit mode condition on meter 3 Record the customer radio presets and other presets as required 4 Turn ignition switch to ON position 5 Put shift lever in P position for A T and CVT or 1st for M T 6 Turn ignition switch to OFF position A CAUTION e Allow 3 min after key off and doors closed for vehicle to time out if doors are opened again additional time may be required Allow an additional 3 min after Positive terminal disconnect before seperating any electrical connectors Fig 1 7 Using a 10mm socket and ratchet disconnect the negative battery terminal Fig 1 Page 2 of 19 999L1 G20001I Rev 7 18 14 INSTALLATION PROCEDURE A CAUTION e Do not use excessive force when removing OE m
6. 5 Foam Tape Wire Tie 21 Locate the driver side Accessory Service Connector It will be located up under the dash along the main body harness assembly on the left side of the vehicle Carefully pull the plug out for easier access Fig 16 Accessory g Service Note A previously installed accessory connector Connector _ may be present If so carefully remove the accessory connector harness from the plug before posi tapping It is recommended that all posi tapping be completed before EC Mirror reattaching the accessory connector to the Vehicle Harness plug Harness Page 6 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE CAUTION This Accessory Service Connector is for use only with Genuine Nissan or Infiniti or Nissan or Infiniti ap proved accessories Use of this connector with non Genuine Nissan or Infiniti or Nissan or Infiniti approved accessories or failure to follow the installation instructions for the connector contained in this package may result in damage to the accessory and or your vehicle Nissan or Infiniti is not liable for loss or damage due to improper installation or the installation of non Genuine or non approved accessories Posi TapTM is protected by patent 5 228 875 5 695 369 5 868 589 6 692 313 Jap 2881414 Aus 708700 Tia 103534 Can 2204826 Mex 200626 Korea 477279 China Z197105562 9 amp others pending 999Q9 AYOO1 Label Color I
7. GENUINE PARTS INSTALLATION INSTRUCTIONS O DESCRIPTION Auto Dimming Mirror with HomeLink and Compass APPLICATION Rogue PART NUMBER 999L1 VZ001 KIT CONTENTS Item Qty Part Description Service Part Number A EC Compass HomeLink Mirror 999L1 VZ000 Parts Kit 999L1 VZ002 Harness Assembly Ignition Battery and Ground Wire Cover Posi tap Wire Tie Foam Tape Tether Clip A Pillar 76988 3DNOA Manual Installation Instruction Download 999V2 AWO000 User Guide Accessory Service Connector NOT INCLUDED IN KIT 999Q9 AY001 A c ir o imimiooj u ajaja NIO OI O gt T E F G TOOLS REQUIRED 3mm Flat Screwdriver Side Cutters Ratchet Nylon Trim Removal Tool 1 Phillips Screwdriver Clean Rag T20 Torx Bit Screwdriver Fish Wire 10mm Socket PRE INSTALLATION WARNINGS CAUTIONS CRITICAL STEPS and NOTES e Dealer Installation Recommended Instructions may refer to Service Manual e For HomeLink Troubleshooting refer to page 18 or call 1 800 355 3515 A CAUTION e This is a universal kit so all parts may not be used e Place removed vehicle trim components in a clean dry area to prevent damage HOMELINK AND THE HOMELINK HOUSE ARE REGISTERED TRADEMARKS OF GENTEX CORPORATION Page 1 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE 1 Apply parking brake 2 Confirm the vehicle is no longer in the default shipping state extended storage
8. GN BAT RED TL LMP RM LMP BATSVR R DR SW R R DR SW LH THRU SIGNAL 1 RR DR RH RR DR LH ACC GND L Pin 6 8 EZ NAI Using a posi tap connect the BLACK WIRE W SILVER CONDUCTOR from the mirror harness to the BLACK wire on the accessory connector harness Using a posi tap connect the BLACK WIRE W WHITE TRACE amp COPPER CONDUCTOR from the mirror harness to the WHITE wire on the accessory connector harness Using a posi tap connect the BLACK WIRE WITH THE BLUE DOT amp COPPER CONDUCTOR from the mirror harness to the RED wire on the accessory connector harness Fig 17 a Reference Page 19 for additional wiring details b See Step 23 37 for posi tap installation instructions WY Verify mirror has been wired properly Note Be sure to NOT to posi tap through the shrink tubing HARNESS NOT INCLUDED IN KIT REFERENCE PART NUMBER 999Q9 AYOO1 Page 7 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE i Straight and evenly spaced all the way around ii Tighten and minimize gap wire jacket should be crushed Fig 20 e Insert wire to here 9 f Tighten q Pani i Straight and evenly spaced all around ii Tight and no gap and test the signal 23 Tap accessory service wire Fig 18 a b c d e f NOTE Identify and confirm correct wire in the Accessory Service Connector to be tapped Remove cap slot side from t
9. ap body Slide cap around single accessory wire Position cap 6 35mm 0 25in away from the heat shrink end of the Accessory Service Connector measurement for first posi tap installed on the circuit Tighten the tap TIGHT with finger pressure Tighten by another quarter turn Figures are not to scale 24 Inspect the tap to ensure correct installation Fig 19 a b C NOTE Pull on wire lightly to ensure connection Inspect the tap to ensure correct installation Test signal to ensure that it is working Avoid putting pressure on the vehicle wire and tap for the remainder of the installation 25 Tap accessory wire Fig 20 Remove tap non pierce side from tap Remove the protective stub from the wire Insert wire through the non pierce side Spread the individual strands into fan shape Insert wire into the tap body and ensure that it is all the way in Tighten the tap TIGHT with finger pressure Tighten by another quarter turn 26 Confirm the tapped accessory wire Fig 21 a b Pull on the wire lightly to ensure connection Inspect the tap to ensure correct installation C Test the signal to ensure it is working Page 8 of 19 999L1 G20001I Rev 7 18 14 INSTALLATION PROCEDURE 27 Forming strain relief loop always required Fig 22 a Gently bend the end of the pierced wire where it exits the cap down toward the body of the posi tap b On the tapped wire of the non p
10. compass display button on EC mirror Any display in compass window Order service part 999L1 VZ000 remove existing EC mirror and replace with new Page 17 of 19 direction is displayed PERFORM CALIBRATION PROCEDURE Compass display reads C 1 Reference Quick Reference card in manual Incorrect direction is displayed Correct direction is displayed Some headings not displayed Order service part 999L1 VZ000 remove existing EC mirror and replace with new Heading is locked in one direction Heading incorrect on long trips NOTE Compass re calibration may be neccessary due to 1 Changes in vehicle magnetics due to installation of luggage racks ski racks etc 2 Vehicle body vibration over time 3 Driving vehicle in new compass zone Ref Quick Reference Card 999L1 G2000II vehicle glove box or EC mirror installation properly Rev 7 18 14 DIAGNOSTIC FLOW CHART HOMELINK TROUBLE SHOOTING GUIDE Part Number 999L1 VZ000 Before attempting to trouble shoot EC mirror HomeLink function ensure the followin 1 Mirror is manufactured by Gentex Corporation the letters GNTX will be etched onto the back of the mirror and the compass display window will be in the mirror alass Orderservice part 999L1 VZ000 remove existing EC mirror and replace with new Press powerbutton 3 Vehicle ianition must be in the ON position Is
11. h electrical tape 2 2 revolutions at a distance of 26 35mm 0 25in as shown in Fig b The pierced wires of the first and subsequent posi taps are secured to each other with electrical tape 2 2 revolutions at a distance of 26 35mm 0 25in as shown in Fig c Page 10 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE 33 Prep for foam wrap Fig 28 a Make sure the accessory taps have been wrapped appropriately as detailed previously and as shown in Fig 28 Service Connector Harness Service 34 Pre foam protective wrap Fig 29 Connector ig a Starting at the heat shrink firmly wrap the posi tap bundle with electircal tape or non adhesive wire harness tape making sure to overlap the previous revolution Harness If using non adhesive tape secure at the of wrap with electrical tape 2 2 revolutions Page 11 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE 35 Finished protective wrap Fig 30 a Make sure the finished wrap looks similar to Fig 30 36 Foam wrap for posi tap bundle foam strips Fig 31 a Wrap the posi tap bundle with foam tape following a pattern similar to the electrical tape making the best use of foam strips provided 37 Finished foam wrap for bundle strips top view Fig 32 a Make sure the finished wrap looks similar to Fig 32 Page 12 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE
12. iecrce side starting at point b1 measure 50 8mm 2in to point b3 Make the first bend of the loop b2 half the distance measured 25 4mm 1in and up toward the body of the posi tap make the second bend of the loop b3 b3 Accessory Secure the pierced wire on the heat shrink side Harness and the tapped wire on the non pierce side to the body of the tap with electrical tape 22 Revolutions Service Connector Harness If securing multiple taps to single circuit continue to Step 28 if tapping different circuits repeat steps 23 27 as required then proceed to step 32 28 Multiple posi taps on the same wire first tap Fig 23 a The first accessory is tapped relieved and secured as shown in Fig 18 thru 22 these steps are always the same b Measure 25 4mm 1in from point b to point c on the pierced wire C At points b amp c bend the pierced wire gently to Accessory form the staircase shape Harness 29 Multiple posi taps second accessory Fig 24 a Tap second accessory at point b making sure to preserve staircase shape b After tapping second accessory form a strain relief loop for the tapped wire on the non pierce side as shown in Fig c and detailed in step 27b NOTE Do not secure before reading step 30 Repeat as necessary Page 9 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE Service Connector Harness 6 35mm 30 Securing
13. irror from windshield The window button may seperate from windshield or the windshield could break 8 Identify the first character of the vehicle VIN as either 5 or K If 5 remove the OE rearview mirror following step 8 1 or if K skip to step 8 2 8 1 a Slide flat end of 3mm screwdriver into opening at bottom of mirror mount until resistance is felt b Apply additional upward force and twist 90 degrees to lift lock spring C Lift mirror upward off mirror mount while applying pressure with screwdriver gt Locking Tab Mm NY 4 Mirror Mount Tool Windshield y Button a Insert the flat end of a 3mm screwdriver into the opening at the bottom of the mirror mount Fig 3 b Push screwdriver up into the mount to disengage locking tab c While still applying upward pressure with the screwdriver grasp the mirror bracket and lift the mirror up towards the headliner and off the mirror mounting bracket Discard mirror 10 Using a panel removal tool loosen the driver side weather strip and remove from the top of the A pillar to the insturment panel Fig 5 Page 3 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE A CAUTION Exercise caution when removing and installing LH front pillar garnish due to side airbag placement Reference Figure 5 below for further detail Do NOT re use LH front pillar garnish clip LH front pillar ga
14. ll result in limited to no movement for the mir ror Fig 10 If a wire cover was removed from the OE mirror discard the OE wire cover and use the new wire cover from kit contents a Route harness into the groove of the wire cover and attach to the mirror mount b Slide the forks on top of the wire cover into the headliner Fig 11 c Verify cover is properly seated and aligned Grasp the mirror and rotate downward Check to ensure wire cover sits flush against the windshield Fig 12 a If there is a gap between the wire cover and the windshield ensure there is enough harness slack from the mirror to the headliner Adjust if necessary Wrap three additional pieces of foam tape around the mirror harness evenly spaced along the headliner as shown Fig 13 a Using a panel removal tool tuck the wire harness between the headliner and the roof Fig 13 Foam Tape Page 5 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE 19 Route the harness down the driver side A pillar and secure to the existing vehicle harness with 5 wire ties Fig 14 20 Wrap 2 pieces of foam tape around the mirror harness and feed the harness through the top of the dash near the a pillar Feed the harness from the upper dash to the lower driver side kick panel area Secure the EC mirror harness to the body harness in the driver side kick panel area with 1 wire tie Fig 1
15. multiple posi taps on the same circuit Fig 25 a Secure the pierced and tapped wires from the first posi tap along with the tapped wire from the non pierce side of the 2nd posi tap to the body of the 2nd tap with electrical tape 2 revolutions Secure the tapped wires from the non pierced sides of each tap to each other with electrical tape 2 2 revolutions at a distance of 26 35mm 0 25in from the head of last posi tap shown in Fig b No single wire should be posi tapped more than 4 times to maintain integrity Repeat as necessary 31 Multiple accessory taps on the same circuit secured Fig 26 a The first accessory is tapped relieved and has the pierced wire on the heat shrink side and the tapped wire on the non pierce side secured to the first tap as shown in Fig a The second accessory is tapped relieved and has the pierced wire the tapped wire on the non pierce side and the tapped wire from the non pierce side of the first posi tap secured to the second tap as shown in Fig b Finally the tapped wires on the non pierce side of the first and subsequent posi taps are secured to each other as shown in Fig c 32 Multiple accessory taps on different circuits secured together Fig 27 a The tapped accessories with wires already secured to tap bodies are stacked slightly staggered on top of each other as shown in Fig a b The tapped wires on the non pierce side of all the posi taps are secured to each other wit
16. n Timing will vary with ambient light levels and a flashlight may be shined on the rearward photocell if needed to accelerate effect Fig 36 Fig 36 Fig 37 HomeLink Buttons LJ Compass Window G Rearward Y 8 OfeY 3 FEM Photocell LED Red LED Dark Cloth or Towel Remove the cover from the forward looking photocell and the mirror will begin to clear Push the N 7 button to ensure compass display shows either a direction such as NE or a C and that it can be turned ON and OFF C Testing is now complete t Compass Zone With the display turned ON push the N button for 3 seconds until a number appears in dis play numbers correspond to regional compass zones Press and release amp button to scroll through zone numbers Release N button when correct zone number is displayed Fig 38 Zone number will disappear and display will return to showing either a directional heading or a C after 5 seconds of no switch activity ULL Calibrate Compass Drive vehicle in circles 360 at 5 mph or less until compass display window shows a direction C Check all Critical Installation Steps Check all torque values L Auto Dimming mirror pg 4 step 13 fig 8 Page 14 of 19 999L1 G2000II Rev 7 18 14 ACCESSORY CHECK L Verify all wiring is secure and not exposed L Trim all excess cable ties flush
17. ngs to the recorded settings Start engine and verify that there are no new Diagnostic Trouble Codes Turn ignition switch to OFF Place the Owner Manual Quick Reference Guide and or other Manual in the glove box Page 15 of 19 999L1 G2000II Rev 7 18 14 DIAGNOSTIC FLOW CHART 4 Smog AK d d d Mirror is manufactured by Gentex Corporation the letters GNTX will be etched onto the back of the mirror and the compass display window will be in the mirror alass 2 EC mirror harness must be fully plugged into EC mirror 3 Vehicle ianition must be in the ON position Is green LED illuminated Press powerbutton on EC mirror i Is green LED illuminated 12V being delivered to EC mirror ENSURE A ILOQ aa Q EU J a Ori VERIFY AUTO DIMMING FUNCTION 1 Coverforward facing photo cell with dark cloth ortape Shine light from flashlight shoplight etc atrearward facing photocell Mirror is functioning properly Does mirror darken Orderservice part 999L1 VZOOO remove existing EC mirror and replace with new NOTE Auto dimming mirror malfunctions may occurdue to Orderservice part 999L1 VZ0000 remove existing EC mirror and replace with new 1 ECharness power wire is securely plugged into blue wire of junction block connector 2 Check fuse corresponding to connection point of junction block to see if it needs to be replaced 3 ECharness ground wire i
18. rnish clip P N 76988 3DNOA MUST be replaced dur ing re installation of garnish Clip A Pillar Garnish A Pillar Garnish 11 Disengage driver side front pillar garnish fixing clip with a panel removal tool cut the clip with a cutter and then remove front pillar garnish a Remove and discard the clips from the vehicle Remove the door sill plate and kick panel from the driver side of the vehicle a Pull up sill plate to disengage the pawls Fig 7 b Remove the sill plate from the body panel c Remove kick panel fixing clips with a panel removal tool and then remove the kick panel Fig 7 13 Install rearview mirror a Plug the harness connector into the back of the mirror pressing firmly until a click is heard Pull GENTLY on the harness to confirm the har ness is seated completely Slide the rearview mirror base over the button on the windshield Using a T 20 Torx head driver tighten the screw on the mirror mount 1 5 2 0 Nm 1 3 ft Ibs Page 4 of 19 999L1 G2000II Rev 7 18 14 INSTALLATION PROCEDURE 14 Wrap 1 piece of foam tape around the harness and using a panel removal tool tuck the harness between the headliner and roof above the EC mirror Fig 9 15 Verify that a approximately 3 75mm of wire are between the bottom of the wire cover and connector on the back of the mirror Failure to allow the appropriate length wi
19. s securely attached to vehicle gounding point 12V being delivered to EC mirror Order service part 999L1 VZ002 remove existing EC mirror wiring and replace with new OQUOI 1 Obstructions blocking either the forward facing or rearward facing photo cells 2 Non factory tinting of windows Page 16 of 19 999L1 G2000II Rev 7 18 14 DIAGNOSTIC FLOW CHART COMPASS TROUBLE SHOOTING GUIDE Part Number 999L1 VZ000 2 J IK AN OSU gt Mirror is manufactured by Gentex Corporation the letters GNTX will be etched onto the back of the mirror and the compass display window will be in the mirror alass EC mirror harness must be fully plugged into EC mirror Vehicle ignition must be in the ON position Any display Correct Mirror is functioning Is green LED illuminated Press power O button on EC mirror Is green LED illuminated 12V being delivered to EC mirror ENSURE 1 EC harness power wire is securely plugged into blue wire of junction block connector Orderservice part 999L1 VZ000 remove 2 Check fuse existing EC corresponding to mirror and connection point of replace with junction block to see if it new needs to be replaced 3 EC harness ground wire is securely attached to vehicle gounding point 12V being delivered to EC mirror Orderservice part 999L1 Vz002 remove existing EC mirror wiring and replace with new in compass window Press
Download Pdf Manuals
Related Search