Falk Ultramite Type UCBN, UCFN, Sizes 03-14 Gear Drives
Contents
1. Mineral EP Lubricants Table 3 Industrial type petroleum based extreme pressure lubricants are preferred The EP lubricants currently recommended are of the sulfur phosphorus type WARNING EP LUBRICANTS IN FOOD PROCESSING INDUSTRY FP lubricants may contain toxic substances and should not be used in the food processing industry without the lubricant manufacturers approval Lubricants which meet USDA H1 classification are suitable for food processing applications Extreme Pressure EP Synthetic Lubricants Synthetic EP Lubricants Table 3 Polyalphaoletin type extreme pressure lubricants are recommended for cold climate operation high temperature applications extended temperature range all season operation and or extended lubricant change intervals WARNING SYNTHETIC LUBRICANTS IN FOOD PROCESSING INDUSTRY Synthetic lubricants may contain toxic substances and should not be used in the food processing industry without the lubricant manufacturers approval Lubricants which meet USDA H1 classification are suitable for food processing applications Oil Levels Sizes 03 and 04 are turnished filled with oil determined by the drive mounting position ordered and require no further lubrication For inclined mounting see Page 6 for lubricant quantities Sizes 06 thru 14 oil levels are determined by drive mounting position Location of the vent drain and oil level plugs are determined by the drive mount2. PERIODICALLY Sizes 06 thru 14 Carefully check the oil level of the drive when it is stopped and at ambient temperature add oil it needed If the oil level is ABOVE the oil level plug have the oil analyzed for water content If moisture content exceeds 500ppm change the oil DO NOT fill above the oil level plug as leakage or undue heating may result Also check coupling alignment to make certain that toundation settling has not caused excessive misalignment Stored amp Inactive Gear Drives Each gear drive is protected with rust preventive that will protect parts against rust for a period of 6 months in an indoor dry shelter Sizes 06 thru 14 It a gear drive is to be stored or is inactive after installation beyond the above periods drain oil from housing and spray all internal parts with a rust preventive oil that is soluble in lubricating oil or add Motorstor vapor phase rust inhibitor at the rate of one ounce per cubic foot of internal drive space or 5 of sump capacity and rotate the shatts several times by hand Before operating drives which have been stored or inactive must be filled to the proper level with oil meeting the specifications given in this manual Refer to Manual 128 014 for Start up after Storage instructions Periodically inspect stored or inactive gear drives and spray or add rust inhibitor every six months or more often if necessary Indoor dry storage is recommended Gear drives ordere
3. Falk Ultramite e Installation amp Maintenance Instructions Types UCBN amp UCFN e Sizes 03 thru 14 Page 1 of 8 How to Use This Manual This manual provides detailed instructions on installation and maintenance of gear drives and couplings Use the table of contents below to locate required information CAREFULLY FOLLOW THE INSTRUCTIONS IN THIS MANUAL FOR OPTIMUM PERFORMANCE AND TROUBLE FREE SERVICE Table of Contents Installation Instructions 0 0 ce eee Page MoUnTING POSINONS 4 4404 44 08 4 toriai EAA R Page 2 Tightening Torques 0 0 0 0 cece eee Page 2 Shaf CONNECHONS 4044 44 ete w ee chad oie ee eA Page 3 Lubrication Recommendations 00005 Page 4 Preventive Maintenance 0 0 0 eee eee Page 5 Stored and Inactive Gear Drives 004 Page 5 Lube Quantities for Incline Mtg Sizes 03 amp 04 Page 6 Lube Quantities for Incline Mtg Sizes 06 amp O7 Page 7 Lube Quantities for Incline Mtg Sizes 08 09 10 12 E PERETE EEEE ee ee a Be Page 8 Introduction Credit for long service and dependable operation of a gear drive is otten given to the engineers who designed it or the crattsmen who constructed it or the sales engineer who recommended the type and size Ultimate credit belongs to the mechanic on the job who worked to make the foundation rigid and level who accurately aligned the shafts and carefully installed the accessories and who made sure
4. 1 Page 2 for the placement of the vent drain and oil level plugs based on the drive mounting position FOUNDATION GENERAL To facilitate oil drainage elevate the gear drive foundation above the surrounding floor level If desired replace the drive oil drain plug with a valve but provide a guard to protect the valve from accidental opening or breakage FOUNDATION STEEL When mounting gear drive on structural steel it is recommended that an engineered design be utilized tor a pedestal adapter base or bed to provide sufficient rigidity to prevent induced loads from distorting the housing and causing gear misalignment In the absence of an engineered design it is recommended that a base plate with thickness equal to or greater than the thickness of the drive feet be securely bolted to steel supports and extend under the entire drive FOUNDATION CONCRETE If a concrete foundation is used allow the concrete to set firmly before bolting down the gear drive For the best type of mounting grout structural steel mounting pads into the mounting base as illustrated rather than grouting the drive directly into the concrete Motors and other components mounted on motor plates may become misaligned during shipment ALWAYS check alignment after installation Rexnord Industries LLC 3001 W Canal St Milwaukee WI 53208 4200 Telephone 414 342 3131 Fax 414 937 4359 e mail info rexnord com web www rexnord com 288 10
5. V mishandling during shipping Type UCBN Type UCFN Installation Instructions The following instructions apply to standard Falk Type UCBN base mounted and UCFN flange mounted drives shown above It a drive is furnished with special features refer to the supplementary instructions shipped with the drive WELDING Do not weld on the gear drive or accessories without prior approval trom the Factory Welding on the drive may cause distortion of the housing or damage to the bearings and gear teeth Welding without prior approval could void the warranty EFFECTS OF SOLAR ENERGY It the gear drive operates in the sun at ambient temperatures over 100 F 38 C then special measures should be taken to protect the drive from solar energy This protection can consist of a canopy over the drive or reflective paint on the drive It neither is possible consult the Factory MOUNTING Figure 1 Page 2 Sizes 03 and 04 are lubricated for life and will be furnished filled with an EP extreme pressure mineral lubricant to the appropriate level determined by the mounting position ordered Synthetic EP lubricants will be furnished upon request at an extra charge Sizes 06 thru 14 are furnished without oil Reter to Table 3 Page 4 for a list of typical lubricants meeting Rexnord specitications Fill drives to the oil level plug Refer to Table 4 Page 5 for the approximate quantities of oil by the drive mounting position Refer to Figure
6. x 1 97 UNF 14 750 x 1 65 UNF 1 00 x 1 97 UNF COUPLING CONNECTIONS The performance and lite of any coupling depends largely upon how well the coupling is installed and serviced Reter to the coupling manutacturer s manual for specific instructions CORRECT METHOD Heat interference titted coupling hubs pinions sprockets or pulleys to a maximum of 275 F 135 C and slide onto gear drive shatt INCORRECT METHOD DO NOT drive coupling hub pinion sprocket or pulley onto the shatt An endwise blow on the shatt coupling may damage gears and bearings FALK COUPLINGS Except fluid type Detailed installation manuals are available from the Factory your local Rexnord Representative or Distributor just provide size and type designations stamped on CAUTION DO NOT HAMMER the coupling For lubricant requirements and a list of typical lubricants meeting Rexnord specifications refer to appropriate coupling service manual GAP AND ANGULAR ALIGNMENT If possible after mounting coupling hubs position the driving and driven equipment so that the distance between shaft ends is equal to the coupling gap Align the shafts by placing a spacer block equal in thickness to required gap between hub faces as shown and also at 90 intervals around the hub Check with feelers OFFSET ALIGNMENT Align driving and driven shatts so that a straight edge will rest squarely on both couplings hubs as s
7. 001 W Canal St Milwaukee WI 53208 4200 Telephone 414 342 3131 Fax 414 937 4359 e mail info rexnord com web www rexnord com 288 101 January 2007 Supersedes 11 02 Installation amp Maintenance Instructions e Falk Ultramite Page 4 of 8 Sizes 03 thru 14 e Types UCBN amp UCFN Lubrication Recommendations Caretully follow lubrication instructions on warning tags and installation manuals furnished with the gear drive Nameplates are stamped with a designation tor recommended lubricant standard is 6E Lubricants listed in this manual are typical ONLY and should not be construed as exclusive recommendations Refer to your lubricant supplier tor additional lubricants meeting the indicated specifications Industrial type extreme pressure EP gear lubricants are the recommended lubricants for ambient temperatures of 15 F to 125 F 9 C to 52 C For drives operating outside the above temperature range refer to Synthetic Lubricants paragraphs Synthetic lubricants can also be used in normal climates VISCOSITY IMPORTANT The proper grades of EP Mineral lubricants and EP Synthetic lubricants are found in Table 3 For cold climates refer to EP Synthetic Lubricant paragraphs Select a lubricant which has a pour point at least 10 F 5 5 C below the expected minimum ambient starting temperature Usable temperature ranges can sometimes be widened if specitic application conditions are kno
8. 1 January 2007 Supersedes 11 02 Installation amp Maintenance Instructions e Falk Ultramite Page 2 of 8 Sizes 03 thru 14 e Types UCBN amp UCFN Mounting 1 Mounting 4 Mounting 3 Mounting 2 Figure 1 Use motor fitted with a seal BREATHER A OIL DRAIN Q OILFILL OIL LEVEL Fastener Tightening Torques Table 1 Tightening Torques lb in 5 Use the tightening torque values specified in Table 1 for DO NOT Lubricate Fasteners fastening gear drives motors and accessories to their mounting Thread Metal to surtaces with non lubricated fasteners DO NOT use these values Dia UNC Concrete for torque locking fasteners or for fastening components with aluminum feet or with soft gaskets or vibration dampers on the mounting surtace If the tightening torque exceeds the capacity of the torque wrench use a torque multiplier Use Grade 5 fasteners for diameters through 1 50 288 101 Rexnord Industries LLC 3001 W Canal St Milwaukee WI 53208 4200 January 2007 Telephone 414 342 3131 Fax 414 937 4359 Supersedes 11 02 e mail info rexnord com web www rexnord com Falk Ultramite e Installation amp Maintenance Instructions Types UCBN amp UCFN e Sizes 03 thru 14 Page 3 of 8 GEAR DRIVE ALIGNMENT Align drive with driven equipment by placing broad flat shims under all mounting pads Start at the low speed shatt end and level across the length and then the
9. 30 5 8 1 5 3 7 6 4 10 5 17 5 32 0 47 0 72 0 17 2 3 5 0 94 10 5 17 5 32 0 72 0 720 6 1 0 1 7 3 4 6 4 10 1 17 2 260 380 65 0 1 5 23 5 0 94 10 1 172 27 0 65 0 67 0 7 6 6 17 3 3 2 6 5 5 8 0 14 0 20 8 3 12 3 4 2 4 6 0 8 0 20 0 20 0 8 8 14 3 1 6 3 25 16 0 22 0 45 0 65 0 1 7 2 5 0 10 0 9 0 16 0 22 0 65 0 65 0 9 1 0 1 6 3 6 6 8 10 5 17 0 28 0 43 0 65 0 I5 2 1 5 0 9 0 10 0 19 0 29 0 65 0 67 0 OBTAIN QUANTITIES FOR REDUCTIONS BELOW BY COMBINING PRIMARY amp SECONDARY Separate Oil Sumps QUANTITIES FROM ABOVE DRIVE Quadruple Reduction Quintuple Reduction SIZE 07UC4 08UC4 09UC4 06UC5 07UC5 08UC5 09UC5 10UC5 Primary 04UC2 04UC2 06UC2 06UC2 07UC2 04UC3 04UC3 06UC2 06UC2 07UC2 Secondary 06UC2 07UC2 08UC2 09UC2 10UC2 06UC2 07UC2 08UC3 09UC3 10UC3 F Convert quantities using the following Liters to US Gallons liters x 0 26 Liters to Imperial Gallons liters x 0 22 Liters to US Quarts liters x 1 057 Rexnord Industries LLC 3001 W Canal St Milwaukee WI 53208 4200 288 101 Telephone 414 342 3131 Fax 414 937 4359 January 2007 e mail info rexnord com web www rexnord com Supersedes 11 02 Installation amp Maintenance Instructions e Falk Ultramite Page 6 of 8 Sizes 03 thru 14 e Types UCBN amp UCFN LUBRICANT QUANTITIES FOR INCLINED MOUNTING SIZES 03 amp 04 For inclinations within 5 use standard lubricant quantity as shown in Table 4 on Page 5 For inclinations above 5 use lub
10. C 5 0 C 6 5 C 9 5 C 66 90 Right 3 5 B 5 0 B 6 5 B 05 B F Convert quantities using the following Liters to US Gallons liters x 0 26 Liters to Imperial Gallons liters x 0 22 Liters to US Quarts liters x 1 057 Rexnord Industries LLC 3001 W Canal St Milwaukee WI 53208 4200 288 101 Telephone 414 342 3131 Fax 414 937 4359 January 2007 e mail info rexnord com web www rexnord com Supersedes 11 02 Installation amp Maintenance Instructions e Falk Ultramite REXNO RD Page 8 of 8 Sizes 03 thru 14 e Types UCBN amp UCFN LUBRICANT LEVELS amp QUANTITIES FOR INCLINE MOUNTING SIZES 08 09 10 For Sizes 12 amp 14 Contact the Factory ELEVATION INCLINED For inclined drives it is important to fill to the correct oil level Oil quantities will vary depending on the angle of incline and plug as shown below NOTE Follow instructions for the drive at the correct inclination TABLE 9 Approximate Oil Quantities amp Plug Positions Liters t ratio Maximum oil quantity liters as shown in Table 9 amp 10 below DRIVE SIZE san Dewn 08UC 09UC 10UC Degrees Drive Type Quantity Plug Quantity Plug Quantity Plug of Incline Position Position Position 0 70 Base Mount 10 5 A 17 5 A 26 A Flange Mount 95 A 16 0 A 22 A Shaft Up 06UC2 06UC3 07UC2 of Incline Drive Type Quantity positon Quantity positon Quantity Position 0 20 Ba
11. d tor extended storage can be treated at the Factory with a special preservative and sealed to rust proot parts for periods longer than those cited previously Table 4 Approximate Oil Quantities Liters Material Safety Data Drives with nameplate designation 6E are tilled with Mobilgear 632 drives with nameplate designation 6H are filled with Mobilgear SHC 320 Material satety data sheets tor these products can available directly trom Mobil Oil Corporation at Products amp Technology Department 3225 Gallows Road Fairfax VA 22037 Phone 800 662 4525 or Phone 703 849 3265 For material satety data sheets pertaining to other products used in the manutacture of the Falk Ultramite contact Rexnord Industries LLC Gear Group Customer Service Department 3001 W Canal Street Milwaukee WI 53208 4200 Phone 414 342 3131 DRIVE SIZE oe Double Reduction Triple Reduction 03UC2 04UC2 06UC2 07UC2 O8UC2 09UC2 10UC2 12UC2 14UC2 03UC3 04UC3 06UC3 07UC3 O8UC3 09UC3 10UC3 12UC3 14UC3 6 6 17 2 8 4 6 10 5 11 0 17 0 240 8 9 1 8 3 0 6 4 11 5 11 0 240 24 0 2 6 6 22 43 13 127 22 0 31 0 49 0 8 3 2 6 oy 73 127 23 0 49 0 50 0 3 8 1 2 2 6 48 78 127 22 0 31 0 49 0 1 0 1 5 3 0 5 8 78 127 230 49 0 50 0 4 8 1 2 2 9 5 8 7 7 19 0 28 0 41 0 1 0 1 5 3 6 74 7 1 12 7 200 41 0 4
12. hown to the right and also at 90 intervals Tighten foundation bolts of the connected equipment and recheck alignment and gap SPROCKETS PULLEYS OR SHEAVES Mount power take otts as close to the gear drive housing as possible to avoid undue bearing load and shaft deflection STEELFLEX ILLUSTRATED Align the output shatt of the gear drive square and parallel with the driven shaft by placing a straightedge across the face of RIGHT WRONG the sprockets or sheaves as og ee illustrated Check horizontal shatt alignment by placing one leg of a square against the tace of the sheave or sprocket with the spirit level on the horizontal leg of the square P GEAR DRIVE WALL LEVEL SQUARE AND PARALLEL DO NOT over tighten belts or chains Adjust chains to manufacturers specifications Adjust belts as follows The ideal tension is the lowest tension at which the belt will not slipo under peak load conditions Check the belt tension frequently during the first 24 to 48 hours of run in operation Over tightening belts shortens belt and bearing life Keep belts free from foreign material which may cause slippage Inspect the V belts periodically tighten the belts if they are slipping PINION MOUNTING Mount pinion as close to the drive as possible to avoid undue bearing load and shaft deflection Refer to the Factory for pinion alignment instructions Rexnord Industries LLC 3
13. ing position and are shown in Figure 1 Page 2 Refer to Table 4 Page 5 for approximate quantities of oil by drive mounting position For inclined mounting for Sizes 06 amp 07 see Page 7 for lubricant quantities Sizes 08 09 10 12 amp 14 see Page 8 for lubricant quantities Lubricant Changes Sizes 06 14 OIL ANALYSIS REPORT Checking oil condition at regular intervals is recommended In the absence of more specitic limits the guidelines listed below may be used to indicate when to change oil 1 Water content is greater than 0 05 500 ppm 2 Iron content exceeds 150 ppm 3 Silicon dust dirt exceeds 25 ppm 4 Viscosity changes more than 15 Sizes 06 07 08 09 10 12 and 14 require an oil change at 2 500 hours for EP mineral lubricants and 10 000 for polyalphaoletin type EP synthetic lubricants 288 101 January 2007 Supersedes 11 02 Rexnord Industries LLC 3001 W Canal St Milwaukee WI 53208 4200 Telephone 414 342 3131 Fax 414 937 4359 e mail info rexnord com web www rexnord com Falk Ultramite e Installation amp Maintenance Instructions Types UCBN amp UCFN e Sizes 03 thru 14 Page 5 of 8 Preventive Maintenance AFTER FIRST WEEK Check alignment of the total system and realign where necessary Also tighten all external bolts and plugs where necessary DO NOT readjust the internal gear or bearing settings in the drive these were permanently set at the Factory
14. ricant quantity liters as shown in Tables 5 amp 6 below SHAFT INCLINED TABLE 5 Approximate Oil Quantities Liters t Shaft Inclined Drive Type DRIVE SIZE Above 5 03UC2 03UC3 04UC2 04UC3 Buse Mount 0 8 17 15 Ve Down Flange Mount 0 8 1 7 1 4 2 1 i Base Mount 1 0 15 i7 23 Flange Mount 1 0 15 T 21 F Convert quantities using the following Liters to US Gallons liters x 0 26 Liters to Imperial Gallons liters x 0 22 Liters to US Quarts liters x 1 057 ELEVATION INCLINED TABLE 6 Approximate Oil Quantities Liters DRIVE SIZE Drive Type 03UC2 03UC3 04UC2 04UC3 Base Mount 0 8 1 0 1 2 15 Flange Mount 0 8 1 0 1 2 1 5 F Convert quantities using the following Liters to US Gallons liters x 0 26 Liters to Imperial Gallons liters x 0 22 Liters to US Quarts liters x 1 057 288 101 Rexnord Industries LLC 3001 W Canal St Milwaukee WI 53208 4200 January 2007 Telephone 414 342 3131 Fax 414 937 4359 Supersedes 11 02 e mail info rexnord com web www rexnord com Falk Ultramite e Installation amp Maintenance Instructions Types UCBN amp UCFN e Sizes 03 thru 14 Page 7 of 8 LUBRICANT LEVELS amp QUANTITIES FOR INCLINE MOUNTING SIZES 06 amp 07 ELEVATION INCLINED Oil quantities will vary depending on the angle of incline and ratio Maximum oil quantity liters as shown in Table 7 amp 8 below For inclined drives it is importan
15. se Mount 7 0 A 13 A 20 A Flange Mount 15 A 12 5 A 19 A 21 90 Base Mount 10 B li B 27 B Flange Mount 10 5 B 19 B 29 B F Convert quantities using the following Liters to US Gallons liters x 0 26 Liters to Imperial Gallons liters x 0 22 Liters to US Quarts liters x 1 057 SHAFT INCLINED TABLE 10 Approximate Oil Quantities amp Plug Positions Liters t DRIVE SIZE br ae Drive Type 08UC 7 09UC R 10UC 7 Quantity Position Quantity Position Quantity Position 0 50 Left 13 A 19 A 27 A 51 90 Left 13 B 19 B 27 B 0 20 Right Base Mount 4 5 A 7 0 A 10 A 21 65 Right 1 C 18 C 26 C 66 90 Right 12 B 18 B 26 B F Convert quantities using the following Liters to US Gallons liters x 0 26 Liters to Imperial Gallons liters x 0 22 Liters to US Quarts liters x 1 057 288 101 January 2007 Supersedes 11 02 Rexnord Industries LLC 3001 W Canal St Milwaukee WI 53208 4200 Telephone 414 342 3131 Fax 414 937 4359 e mail info rexnord com web www rexnord com
16. t to fill to the correct oil level plug as shown below NOTE Follow instructions for the drive at the correct inclination TABLE 7 Approximate Oil Quantities amp Plug Positions Liters Shaft D DRIVE SIZE pica 06UC2 06UC3 07UC2 07UC3 Degrees Plug Plug Plug i Plug of Incline Drive Type Quantity Position Quantity Position Quantity Position Quantity Position All Base Mount Jul A 5 0 6 4 A 94 C Flange Mount 3 1 A 5 0 C 6 3 A 10 C Shaft Up 06UC2 06UC3 07UC2 07UC3 Degrees 3 Plug Plug Plug Plug of Incline Drive Type Quantity Position Quantity Position Quantity Position Quantity Position 9 30 Base Mount 2 0 A 2 2 A 3 5 A 37 A Flange Mount 2 0 A 2 2 A 4 0 A 4 2 A 31 60 Base Mount 3 4 B 5 0 B 6 4 B 94 B Flange Mount 3 6 5 0 6 8 94 F Convert quantities using the following Liters to US Gallons liters x 0 26 Liters to Imperial Gallons liters x 0 22 Liters to US Quarts liters x 1 057 SHAFT INCLINED TABLE 8 Approximate Oil Quantities amp Plug Positions Liters t DRIVE SIZE aor Drive Type 06UC2 06UC3 07UC2 07UC3 jiii Quantit Plug Quantit Plug Quantit Plug Quantit Plug y Position Y Position y Position y Position 0 50 Left 5 5 A 5 0 A 6 5 A 95 A 51 90 Left 3 5 B 5 0 B 6 5 B 9 5 B 0 20 Right Base Mount 7 1 8 2 8 3 0 21 65 Right 3 0
17. that the drive received lubrication at prescribed intervals The details of this important job are the subject of this manual NAMEPLATE Operate Rexnord gear drives only at horsepower speed and ratio shown on nameplate and in the mounting position for which it was ordered Before changing any one of these submit complete nameplate data and new application conditions to the Factory for correct oil level parts and application approval WARNING Consult applicable local and national safety codes for proper guarding of rotating members Lock out power source and remove all external loads from drive before servicing drive or accessories Warranty Rexnord Industries LLC the Company warrants that Ultramite gear drives I conform to Company s published specifications and ll are tree trom defects of material for three years from the date of shipment Company does not warrant any non Company branded products or components manutacturer s warranty applies or any detects in damage to or failure of products caused by I dynamic vibrations imposed by the drive system in which such products are installed unless the nature of such vibrations has been defined and accepted in writing by Company as a condition of operation Il failure to provide suitable installation environment Ill use for purposes other than those for which designed or other abuse or misuse IV unauthorized attachments modifications or disassembly or
18. width of the drive Check with a teeler gauge to make certain that all pads are supported to prevent distortion of housing when drive is bolted down After drive is aligned with driven equipment and bolted down align prime mover to drive input shaft Refer to next column for coupling alignment Check high speed shaft coupling alignment If the coupling is misaligned the drive is shimmed incorrectly Re shim drive and recheck high speed coupling alignment If necessary realign motor Shaft Connections WARNING Provide suitable guards in accordance with OSHA standards Input and output shaft extension diameter tolerance is 0000 0005 for shafts up to 1 375 diameter and 000 001 for shatts larger than 1 375 diameter The titted component must be machined to ensure proper Tit DO NOT drive coupling hub pinion sprocket or pulley on the shatt An endwise blow on the shatt may damage gears and bearings Coupling hubs pinions sprockets or pulleys must be pushed onto the shatt using a screw jack device fitted into the threaded hole provided in the end of the shatt see Table 2 below Table 2 Shaft End Threaded Holes Inches DRIVE SIZE Input Shaft Output Shaft 03 250 x 500 UNF 250 x 630 UNF 04 250 x 500 UNF 250 x 630 UNF 06 250 x 630 UNF 375 x 870 UNF 07 312 x 630 UNF 625 x 1 42 UNF 08 312 x 870 UNF 625 x 1 42 UNF 09 500 x 1 10 UNF 750 x 1 65 UNF 10 625 x 1 42 UNF 750 x 1 65 UNF 12 750 x 1 65 UNF 1 00
19. wn Table 3 Typical Lubricants Recommendations amp Specifications AGMA Viscosity Grade ban 5EP 6EP 7EP ISO Viscosity Grade Mineral Lubricants 220 320 460 Extreme Pressure Nameplate Designation 5E 6E 7E Ambient Temperature Range F 23 to 32to 50 to Manufacturer Lubricant 77 104 122 Chevron USA Inc Gear Compounds EP 220 320 460 Exxon Co USA Spartan EP 220 320 460 Mobil Oil Corp Mobilgear 630 632 634 Shell Oil Co Omala Oil a 220 320 460 AGMA Viscosity Grade 0S 2S 5S 6S 7S Synthetic Lubricants ISO Viscosity Grade Extreme Pressure Except 32 68 220 320 460 where noted t Nameplate Designation 0H 2H 5H 6H 7H Ambient Temperature Range F 30to I5to 14to 32to 50 to Manufacturer Lubricant 10 50 86 113 122 Conoco Inc Syncon 32 t 68 220 See a Exxon Co USA Spartan Synthetic EP eP 220 320 460 Mobil Oil Corp Mobilgear SHC in o 220 320 460 Mobil SHC 624 t 626 t as ae YA Pennzoil Prod Co Super Maxol S P 68 220 320 460 Shell Oil Co Hyperia S ne 220 S 460 Sun Company Inc Sunoco Challenge EP _ 220 320 n Sunoco Challenge AC 32 t 68 t a Consult lubricant supplier manufacturer for maximum operating temperature t Lubricant does not contain EP extreme pressure additives Consult your lubricant supplier for additional lubricant recommendations Extreme Pressure EP Mineral Lubricants
Download Pdf Manuals
Related Search