Oracle® Switch ES2-72 and Oracle Switch ES2
Contents
1. ree MA MAHMTUMT 2 Locate the cable to be removed 3 Grasp the cable connector to support its weight and apply the removal force 4 Disconnect the cable from the connector Fora dual part QSFP cable assembly pull the optical cable connector retraction handle and gently pull out the optical cable Fora single part passive copper QSFP cable pull on the retractor strap while simultaneously pulling on the cable connector 5 Carefully move the cable out of the cable management hardware 6 Gently lower the cable to the floor A Caution Do not allow the cable to drop or strike the floor Jerking bending pulling on or dropping the cable can damage the cable 7 Fora dual part QSFP module assembly remove the optical transceiver module from the slot 36 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Install a Data Cable a Replace the protective end cap if you plan to store the module b Slide out the optical transceiver module c Replace the protective end cap if you plan to store the module 8 Consider your next step If you are removing a single cable for replacement install the new cable See Install a Data Cable on page 37 m f you are disconnecting all cables for switch replacement repeat from Step 2 for all cables Related Information Switch Installation understanding data cabling V Install a Data Cable 1 Remove a2. content products and services from third parties Oracle Corporation and its affiliates are not responsible for and expressly disclaim all warranties of any kind with respect to third party content products and services unless otherwise set forth in an applicable agreement between you and Oracle Oracle Corporation and its affiliates will not be responsible for any loss costs or damages incurred due to your access to or use of third party content products or services except as set forth in an applicable agreement between you and Oracle Documentation Accessibility For information about Oracle s commitment to accessibility visit the Oracle Accessibility Program website at http www oracle com pls topic lookup ctx acc amp id docacc Access to Oracle Support Oracle customers that have purchased support have access to electronic support through My Oracle Support For information visit http www oracle com pls topic lookup ctx acc amp id info or visit http www oracle com pls topic lookup ctx acc amp id trs if you are hearing impaired R f rence E60187 01 Copyright 2015 Oracle et ou ses affili s Tous droits r serv s Ce logiciel et la documentation qui l accompagne sont prot g s par les lois sur la propri t intellectuelle Ils sont conc d s sous licence et soumis des restrictions d utilisation et de divulgation Sauf stipulation expresse de votre contrat de licence ou de la loi vous ne pouvez pas copier reproduire
3. data cable See Remove a Data Cable on page 35 2 Bring the replacement cable to the switch 3 Feed the cable through the CMA 4 Attach a cable to the switch a Visually inspect the cable connector The shell should not be bent and should be parallel to the inner boards If the connector is bent or damaged use a different cable b Ensure that the retraction strap lever is in the attached position c Determine if you are installing a dual part assembly or a single part assembly Some optical transceiver modules are dual part assemblies where the module and the cable are two separate pieces while other optical transceiver modules are single part assemblies where the module and the cable are a single combined unit m Ifyou are installing a dual part module go to Step 5 Servicing Data Cables 37 Install a Data Cable If you are installing a single part module go to Step 6 5 Install the dual part optical transceiver module a Remove the protective end cap from the module b Pull the locking handle into the full horizontal position until you feel the handle click into position c Verify that you have the transceiver module in the correct alignment before inserting it into the slot The following figure shows the correct alignment for the transceiver module d Holding the optical transceiver module by the edges align the optical transceiver module with the slot in the switch and slide it into the
4. opening e Applying even pressure at both corners of the optical transceiver module push the module until it is firmly seated in the slot f Push the handle closed to lock the optical transceiver module in place 38 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Install a Data Cable Note If you pull the locking handle down when the QSFP optical transceiver module is installed you should remove the optical transceiver module entirely and reinstall it The handle operates an internal lock Pulling the handle down can disconnect the module even though it might appear to be connected If you are plugging in a single part cable assembly transceiver and cable combined orient the cable connector horizontally Ensure that the L groove is up for the top row of receptacles or that the L groove is down for the bottom row of receptacles Servicing Data Cables 39 Install a Data Cable 7 Plug the cable into the connector Note The optical transceiver handle must be closed before attaching the cable to the transceiver The handle locks the transceiver in place in the switch port m f you are plugging in a fiber dual part cable assembly transceiver and cable separate verify that the handle is in the locked position and connect the cable to the optical transceiver If the handle is in the unlocked position you must push it up into the locked position before attaching the cable I
5. or motherboard sensor in Component Sensor Targets on page 14 or Motherboard Sensor Targets on page 15 For example to display the status of the fan 0 Attention LED type gt show SYS FMO SERVICE value SYS FMO SERVICE Properties value Off Related Information Component Sensor Targets on page 14 Motherboard Sensor Targets on page 15 m Check Switch Status LEDs on page 12 Component Sensor Targets Use the targets from this table to check the switch status See Check Switch Status Oracle ILOM on page 13 Some sensors indicate the state of LEDs See Rear Panel LEDs on page 11 Component Sensor Target Notes Switch fault SYS SERVICE State of chassis Attention LED Switch locator SYS LOCATE State of chassis Locator LED Switch OK SYS 0K State of chassis OK LED Fan fault SYS FMX SERVICE where x is 0 or 1 state of fan Attention LED Fan presence SYS FMX PRSNT where x is 0 or 1 Fan speed SYS FMX FANy TACH where x is 0 or 1 and y is 0 or 1 Power supply fault SYS PSy SERVICE where y is 0 or 1 state of power supply Attention LED Power supply presence SYS PSy PRSNT where y is 0 or 1 Power supply OK SYS PSy 0K where y is 0 or 1 state of power supply OK LED Related Information m Check Switch Status Oracle ILOM on page 13 Motherboard Sensor Targets on page 15 14 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Moth
6. subject to license terms and license restrictions applicable to the programs No other rights are granted to the U S Government Ce logiciel ou mat riel a t d velopp pour un usage g n ral dans le cadre d applications de gestion des informations Ce logiciel ou mat riel n est pas con u ni n est destin tre utilis dans des applications risque notamment dans des applications pouvant causer des dommages corporels Si vous utilisez ce logiciel ou mat riel dans le cadre d applications dangereuses il est de votre responsabilit de prendre toutes les mesures de secours de sauvegarde de redondance et autres mesures n cessaires a son utilisation dans des conditions optimales de s curit Oracle Corporation et ses affili s d clinent toute responsabilit quant aux dommages caus s par l utilisation de ce logiciel ou mat riel pour ce type d applications Oracle et Java sont des marques d pos es d Oracle Corporation et ou de ses affili s Tout autre nom mentionn peut correspondre des marques appartenant d autres propri taires qu Oracle Intel et Intel Xeon sont des marques ou des marques d pos es d Intel Corporation Toutes les marques SPARC sont utilis es sous licence et sont des marques ou des marques d pos es de SPARC International Inc AMD Opteron le logo AMD et le logo AMD Opteron sont des marques ou des marques d pos es d Advanced Micro Devices UNIX est une marque d pos e d Th
7. Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual Part No E60187 01 April 2015 ORACLE Part No E60187 01 Copyright 2015 Oracle and or its affiliates All rights reserved This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws Except as expressly permitted in your license agreement or allowed by law you may not use copy reproduce translate broadcast modify license transmit distribute exhibit perform publish or display any part in any form or by any means Reverse engineering disassembly or decompilation of this software unless required by law for interoperability is prohibited The information contained herein is subject to change without notice and is not warranted to be error free If you find any errors please report them to us in writing If this is software or related documentation that is delivered to the U S Government or anyone licensing it on behalf of the U S Government then the following notice is applicable U S GOVERNMENT END USERS Oracle programs including any operating system integrated software any programs installed on the hardware and or documentation delivered to U S Government end users are commercial computer software pursuant to the applicable Federal Acquisition Regulation and agency specific supplemental regulations As such use duplication disclosure mo
8. atus Green Has three states Activity for 40GbE connection m Off No link or activity on the QSFP port m On A link has been established on the QSFP port m Blinking There is activity on the QSFP port 7 Oracle Switch ES2 64 only Green Has three states 10GBaseT port Ethernet Link Status Activity m Off No link or activity on the port m On A link has been established on the port m Blinking There is activity on the port Related Information Rear Panel LEDs on page 11 Check Switch Status LEDs on page 12 Rear Panel LEDs The power supply and fan status LEDs are located at the front of the switch Detecting and Managing Faults 11 Check Switch Status LEDs No Name Color State and Meaning 2 Power Supply OK Green On Power supply is functional without fault Off Power supply is off or initializing 3 Power Supply Attention Yellow On Fault detected 12 VDC shut down Off No faults detected 4 Power Supply AC Green On AC is functional without fault Off AC is off or initializing 1 Fan Module Attention Yellow On Fan module has a fault Off No faults detected Related Information Front Panel LEDs on page 9 Check Switch Status LEDs on page 12 Vv Check Switch Status LEDs Check the LEDs to verify the switch status 12 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Sensors Overview See Front Pane
9. dification and adaptation of the programs including any operating system integrated software any programs installed on the hardware and or documentation shall be subject to license terms and license restrictions applicable to the programs No other rights are granted to the U S Government This software or hardware is developed for general use in a variety of information management applications It is not developed or intended for use in any inherently dangerous applications including applications that may create a risk of personal injury If you use this software or hardware in dangerous applications then you shall be responsible to take all appropriate fail safe backup redundancy and other measures to ensure its safe use Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this software or hardware in dangerous applications Oracle and Java are registered trademarks of Oracle and or its affiliates Other names may be trademarks of their respective owners Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc AMD Opteron the AMD logo and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices UNIX is a registered trademark of The Open Group This software or hardware and documentation may provide access to or information about
10. e Open Group Ce logiciel ou mat riel et la documentation qui l accompagne peuvent fournir des informations ou des liens donnant acc s des contenus des produits et des services manant de tiers Oracle Corporation et ses affili s d clinent toute responsabilit ou garantie expresse quant aux contenus produits ou services manant de tiers sauf mention contraire stipul e dans un contrat entre vous et Oracle En aucun cas Oracle Corporation et ses affili s ne sauraient tre tenus pour responsables des pertes subies des co ts occasionn s ou des dommages caus s par l acc s des contenus produits ou services tiers ou leur utilisation sauf mention contraire stipul e dans un contrat entre vous et Oracle Accessibilit de la documentation Pour plus d informations sur l engagement d Oracle pour l accessibilit la documentation visitez le site Web Oracle Accessibility Program l adresse http www oracle com pls topic lookup ctx acc amp id docacc Acc s au support lectronique Les clients Oracle qui ont souscrit un contrat de support ont acc s au support lectronique via My Oracle Support Pour plus d informations visitez le site http www oracle com pls topic lookup ctx acc amp id info ou le site http ww oracle com pls topic lookup ctx acc amp id trs si vous tes malentendant Contents Using This Documentation 7 Detecting and Managin
11. e Switch ES2 64 Service Manual April 2015 10 10GbE ACL CMA DHCP GARP GMRP GVRP LA Glossary 10 Gigabit Ethernet Access control list Cable management assembly Dynamic Host Configuration Protocol Generic Attribute Registration Protocol GARP Multicast Registration Protocol GARP VLAN Registration Protocol Link aggregation Glossary 45 Oracle ILOM O Oracle ILOM Oracle Switch ES2 64 Oracle Switch ES2 72 OSPF QSFP SEFOS SEL SR STP switch Oracle Integrated Lights Out Manager ILOM provides advanced server processor hardware and software to manage and monitor servers An Ethernet switch by Oracle Oracle Switch ES2 64 provides six QSFP ports and 40 10GBASE T RJ 45 ports See also switch An Ethernet switch by Oracle Oracle Switch ES2 72 provides 18 QSFP ports See also switch Open Shortest Path First Protocol Quad small form factor pluggable QSFP is a hot pluggable transceiver that provides 40 Gb s or 4 x 10 Gb s of data transfer Routing Information Protocol Rapid Spanning Tree Protocol Sun Ethernet Fabric Operating System A full featured fabric and switch management software package for configuring and monitoring the switches network infrastructure System event log The switch includes a number of replaceable component sensors that generate entries in the SEL when the sensor crosses a threshold Many of these readings are used to adj
12. erboard Sensor Targets Motherboard Sensor Targets Use the targets from this table to check the switch status See Check Switch Status Oracle ILOM on page 13 Motherboard Sensor Target CPU temperature 14 temperature 12V input 5V output 1 25V for switch chips 1 2 amp 3 1 25V for switch chips 4 5 amp 6 1 25V for switch chips 7 8 amp 9 1 5V output 2 5V output 3 3V input Battery output Core voltage DDR memory SYS MB T_AMB SYS MB T_ SWITCH SYS MB V_ 12V SYS MB V_ 5V SYS MB V_1V25_SW123 SYS MB V_1V25_ SW456 SYS MB V_1V25_ SW789 SYS MB V_1V5 SYS MB V_2V5 SYS MB V_3V3 SYS MB V_BAT SYS MB V_CORE SYS MB V_DDR Related Information Check Switch Status Oracle ILOM on page 13 Component Sensor Targets on page 14 Detecting and Managing Faults 15 16 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Preparing for Service These topics describe how to prepare the switch for power supply or fan module replacement Step Description Links 1 Review the ESD precautions ESD Precautions on page 17 2 Gather tools for service Tools Needed for Service on page 18 3 Familiarize yourself with the location of the replaceable Replaceable Components on page 18 components Related Information Detecting and Managing Faults Servicing Power Supplies Servicing Fan Modules ESD P
13. es 2 Power supplies Servicing Power Supplies Related Information ESD Precautions on page 17 Tools Needed for Service on page 18 Preparing for Service 19 20 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Servicing Power Supplies Perform these tasks in order Preparing for Service Power Off a Power Supply on page 21 Remove a Power Supply on page 22 Install a Power Supply on page 24 Power On a Power Supply on page 26 Related Information Detecting and Managing Faults Preparing for Service Servicing Fan Modules Vv Power Off a Power Supply Note Powering off both power supplies powers off the switch Note Power supplies are hot swappable 1 Prepare for Service See Preparing for Service 2 Determine which power supply to remove m See Check Switch Status LEDs on page 12 m See Check Switch Status Oracle ILOM on page 13 3 Remove the power cord from the respective power supply Servicing Power Supplies 21 Remove a Power Supply The power supply is completely powered off 4 Remove the power supply See Remove a Power Supply on page 22 Related Information Remove a Power Supply on page 22 Install a Power Supply on page 24 Power On a Power Supply on page 26 Y Remove a Power Supply 22 1 Identify whic
14. fyou are plugging in a single part assembly slowly slide the connector into the receptacle a Ifthe cable stops or binds after about 1 4 in 5 mm travel back out and repeat 40 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Install a Data Cable b Ifthe connector stops or binds with about 1 8 in 2 mm still to go back out and repeat 8 Continue to push the connector in until you feel a detent 9 Ifthe switch has a CMA place the cable into an open slot Servicing Data Cables 41 Install a Data Cable 10 Route the data cables so that they do not interfere with other cables with servicing the switch or with other systems Use hook and loop fastener straps to bundle and secure the cables A Caution Do not use cable zip ties to bundle or secure the cable because the ties damage the wires inside the cable 11 Check that the Link LEDs for cabled links are lit green If the Link LED is off the link is down If the Link LED flashes there are errors See Front Panel LEDs on page 9 12 If the switch has a CMA replace the CMA cover and tighten the screws 42 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Install a Data Cable Related Information Switch Installation understanding data cabling Switch Installation data cable guidelines Servicing Data Cables 43 44 Oracle Switch ES2 72 and Oracl
15. g Faults 9 Front Panel EEDS se en NE RM ne Nm ss NA 9 Rear Panel A H D R EEEE EET EET 11 Y Check Switch Status LEDS 2 0 0 0 ccc ceccceeccececeeec cece eee ceeeeceneeseeeeeseeeeeeeees 12 Sensors OVELVIEW suisse nent ce derseeentssssaene te dae ssicues EEA ARE ESE sate self tie on 13 Y Check Switch Status Oracle ILOM ccceceseeeeeeeeceeeceeeceeeeeeeeeeeeeeeeeees 13 Component Sensor Targets riie sie esineen Eaa a a ETE NEEE risi 14 Motherboard Sensor Targets esses 15 Preparing for Service eessessesserrrsssrrerisssrresrstseserrsdsrertesssesrerdtsssstrssseserssset 17 ESD Precautions ssni nens anaia ae arna o a ESEE a dette E POETES 17 Tools Needed for Service e s eesseessesseeeseerrssrseresstessresstesstesstesseesseeseeesseeseee 18 Replaceable Components uses 18 Servicing Power Supplies 21 Y Power Off a Power Supply ses 21 Y Remove a Power Supply essieu 22 Y Install a Power Supply ses 24 Y Power On a Power Supply see 26 Servicing Fan Modules 544 244 5h lose itsepeeoiuneeesbsspeseinaene esse 29 Y Remove a Fan Module ss 29 y Installa Fan Mod le isien 6 nn EE tt net tete 31 Servicing Data Cables 0 cece cccseececeeeeececeaaeeceeeaaeeceeeaaeeeeeaaeneeeeaaeeeeeeaes 35 Y Remove a Data Cable issus siens seessrssessenesssnes 35 y Insta
16. h power supply to remove and power off the power supply See Power Off a Power Supply on page 21 2 Press and hold the release tab to the left and pull on the handle of the power supply Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Remove a Power Supply 3 Continue to pull the handle to remove the power supply from the switch Servicing Power Supplies 23 Install a Power Supply 4 Set the power supply aside on the antistatic mat See ESD Precautions on page 17 5 Install a replacement power supply See Install a Power Supply on page 24 Related Information Power Off a Power Supply on page 21 Install a Power Supply on page 24 Power On a Power Supply on page 26 V Install a Power Supply 1 Power off and remove the power supply to be replaced See Power Off a Power Supply on page 21 24 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Install a Power Supply Remove a Power Supply on page 22 Verify that the slot where you are installing the power supply is clean and free of debris Orient the power supply with the status LEDs on the left and the release tab on the right Slide the power supply into the open slot pushing at the handle When the power supply seats push firmly so that the release tab clicks to secure the power supply into the switch Servicing Power Sup
17. ing data cables 35 fan module 29 power supplies 21 switch 9 switch checking status LEDs 12 Oracle ILOM 13 powering off 21 sensors 13 servicing 9 T targets component sensors 14 motherboard sensors 15 tools 48 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 18
18. l LEDs on page 9 and Rear Panel LEDs on page 11 Related Information Check Switch Status Oracle ILOM on page 13 Sensors Overview The switch uses several configurable sensors and indicators to monitor switch power voltage and temperature The switch includes a sensor for each replaceable component These sensors generate entries in the SEL when sensor thresholds are exceeded Many of these readings are used to adjust the fan speeds and perform other actions such as illuminating LEDs and powering off the switch You can also configure these sensors to generate IPMI PET and SNMP traps as described in the Sun Integrated Lights Out Manager ILOM CLI Procedures Guide A Caution Do not use any interface other than the Oracle ILOM CLI or web interface to alter the state or configuration of any sensor or LED Doing so could void your warranty You can view the system monitoring sensors and indicator parameters from the Oracle ILOM CLI or web interface Related Information Check Switch Status Oracle ILOM on page 13 Vv Check Switch Status Oracle ILOM 1 Log into Oracle ILOM Refer to the Oracle Switch ES2 72 and Oracle Switch ES2 64 Installation Guide for instructions 2 Display the status of parameters of switch components or the motherboard gt show target value Detecting and Managing Faults 13 Component Sensor Targets where target is the Oracle ILOM target name of the component
19. ll a Data Gable iis iccsccississcsssdseeas cass i rnek eenia aeea aE aE aD aaah 37 Contents Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Using This Documentation Overview Describes how to troubleshoot and maintain the Oracle Switch ES2 72 and Oracle Switch ES2 64 Audience Enterprise network and system administrators with experience installing network hardware and software Required knowledge Advanced experience working with hardware and software Product Documentation Library Late breaking information and known issues for this product are included in the documentation library at http www oracle com goto es2 72 es2 64 docs Feedback Provide feedback about this documentation at http www oracle com goto docfeedback Using This Documentation Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Detecting and Managing Faults These topics describe how to detect and manage faults Front Panel LEDs on page 9 Rear Panel LEDs on page 11 Check Switch Status LEDs on page 12 m Sensors Overview on page 13 Check Switch Status Oracle ILOM on page 13 Component Sensor Targets on page 14 Motherboard Sensor Targets on page 15 Related Information Preparing for Service Servicing Power Supplies Servicing Fan Modules Front Panel LEDs The network management status li
20. nal to meet specification A Caution The switch can continue to run safely with one failed fan If a fan fails replace it as soon as possible The system might overheat if more than one fan fails 1 Prepare for service See Preparing for Service 2 Determine which fan is to be removed m See Check Switch Status LEDs on page 12 m See Check Switch Status Oracle ILOM on page 13 3 Loosen the green captive thumbscrew at the right side of the fan Servicing Fan Modules 29 Remove a Fan Module 4 Grasp the black handle and gently pull the fan module out of the switch 30 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Install a Fan Module 5 Set the fan module aside on an antistatic mat See ESD Precautions on page 17 6 Install a replacement fan module See Install a Fan Module on page 31 Related Information m Remove a Power Supply on page 22 Install a Fan Module on page 31 V Install a Fan Module A Caution In a hot swap replacement you must install the replacement fan module within 30 seconds of removing the faulted fan module If this is not possible first power off the switch by powering off both power supplies See Power Off a Power Supply on page 21 1 Remove a fan Servicing Fan Modules 31 Install a Fan Module See Remove a Fan Module on page 29 2 Verify that the slot where the fan module ins
21. nk status and switch status LEDs are located at the front of the switch Detecting and Managing Faults 9 Front Panel LEDs Note The System Fault Alarm Yellow and System OK Green LEDs cannot be on at the same time 13 16 40GbE 13 17 20 40GbE 17 21 24 40GbE 21 1 4 40GbE 1 No Name Color Description Network Management Link and Green Activity Locate White Yellow Attention OK Green Link left m On 10 or 100BASE T link m Off No link or link down Activity right m Off No activity m Flashing Packet activity Helps locate the switch m Off No locate command invoked E Fast blink Occurs one second after the locate command is invoked Has two states m Off No fault m On solid A fault in the system is present and service action is required Has three states Slow blink During startup and shutdown sequences On solid System normal and operational Off Power interruption or system fault Note The off state could be triggered by one power supply being unplugged The switch is still fully 10 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Rear Panel LEDs No Name Color Description operational with only one power supply but this LED is changed to the off state when one power supply is unplugged or not functioning correctly 5 Service Processor 6 QSFP port Ethernet Link St
22. plies 25 Power On a Power Supply 6 Power on the power supply See Power On a Power Supply on page 26 Related Information Power Off a Power Supply on page 21 Remove a Power Supply on page 22 Power On a Power Supply on page 26 V Power On a Power Supply 1 Reconnect the power cord to the power supply 26 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Power On a Power Supply The AC LED lights green to indicate the power supply is connected to line power A moment later the OK LED lights green to indicate the power supply is fully operational Verify that the switch has power See Check Switch Status LEDs on page 12 Related Information Power Off a Power Supply on page 21 Remove a Power Supply on page 22 Install a Power Supply on page 24 Servicing Power Supplies 27 28 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Servicing Fan Modules Perform these tasks in order Preparing for Service Remove a Fan Module on page 29 Install a Fan Module on page 31 Related Information Detecting and Managing Faults Preparing for Service Servicing Power Supplies Y Remove a Fan Module Note The fan module is hot swappable and does not require powering down The fan module has five fan units and requires a minimum of four to be functio
23. recautions A grounded antistatic wrist strap is shipped with your switch Electronic equipment is susceptible to damage by static electricity Use a grounded antistatic wrist strap foot strap or equivalent safety equipment to prevent ESD when you install or service the switch A Caution To protect electronic components from electrostatic damage which can permanently disable the switch or require repair by service technicians place components on an antistatic surface such as an antistatic discharge mat an antistatic bag or a disposable antistatic mat Wear an antistatic grounding strap connected to a metal surface on the switch when you work on switch components Related Information Tools Needed for Service on page 18 Preparing for Service 17 Tools Needed for Service m Replaceable Components on page 18 Tools Needed for Service To install or service the switch you must have these tools m No 2 Phillips screwdriver ESD mat and grounding strap In addition you must provide a system console device such as ASCII terminal Workstation Terminal server Patch panel connected to a terminal server Related Information ESD Precautions on page 17 Replaceable Components on page 18 Replaceable Components 18 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Replaceable Components Description Links al Fan modules Servicing Fan Modul
24. talls is clean and free of debris 3 Orient the fan module with the thumbscrew on the right 4 Firmly slide the fan into the switch until the fan stops The fan should immediately power on 5 Tighten the captive thumbscrew to secure the fan in the switch chassis 32 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Install a Fan Module Verify that air is moving through the fan module Verify that the fan Attention LEDs are no longer illuminated See Rear Panel LEDs on page 11 Related Information Remove a Fan Module on page 29 Install a Power Supply on page 24 Servicing Fan Modules 33 34 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Servicing Data Cables These topics describe how to service data cables Remove a Data Cable on page 35 Install a Data Cable on page 37 Related Information Detecting and Managing Faults Preparing for Service vV Remove a Data Cable This procedure describes how to remove the cables from the switch chassis so that a cable can be replaced If you are removing all cables for switch replacement label each cable with its socket number then start removing the cables from the left side of the switch working your way to the right 1 Ifthe switch has a CMA loosen two thumbscrews to remove the CMA cover Servicing Data Cables 35 Remove a Data Cable
25. traduire diffuser modifier breveter transmettre distribuer exposer ex cuter publier ou afficher le logiciel m me partiellement sous quelque forme et par quelque proc d que ce soit Par ailleurs il est interdit de proc der a toute ing nierie inverse du logiciel de le d sassembler ou de le d compiler except a des fins d interop rabilit avec des logiciels tiers ou tel que prescrit par la loi Les informations fournies dans ce document sont susceptibles de modification sans pr avis Par ailleurs Oracle Corporation ne garantit pas qu elles soient exemptes d erreurs et vous invite le cas ch ant a lui en faire part par crit Si ce logiciel ou la documentation qui l accompagne est conc d sous licence au Gouvernement des Etats Unis ou toute entit qui d livre la licence de ce logiciel ou utilise pour le compte du Gouvernement des Etats Unis la notice suivante s applique U S GOVERNMENT END USERS Oracle programs including any operating system integrated software any programs installed on the hardware and or documentation delivered to U S Government end users are commercial computer software pursuant to the applicable Federal Acquisition Regulation and agency specific supplemental regulations As such use duplication disclosure modification and adaptation of the programs including any operating system integrated software any programs installed on the hardware and or documentation shall be
26. ust the fan speeds and perform other actions such as illuminating LEDs and powering off the switch Short range A short range optical transceiver module Spanning Tree Protocol Shortened name for the Oracle Switch ES2 64 and Oracle Switch ES2 72 See also Oracle Switch ES2 64 and Oracle Switch ES2 72 46 Oracle Switch ES2 72 and Oracle Switch ES2 64 Service Manual April 2015 Index A activity LEDs 9 Attention LED 9 C checking switch status LEDs 12 Oracle ILOM 13 component sensor targets 14 D data cables servicing 35 E ESD precautions for service 17 F fan module installing 31 removing 29 servicing 29 front panel LEDs 11 l installing fan module 31 power supplies 24 L LEDs activity 9 Attention 9 front panel 11 link 9 Locate 9 network management 9 OK 9 rear panel 9 switch status 9 link LEDs 9 Locate button and LED 9 M motherboard sensor targets 15 O OK LED 9 Oracle ILOM checking switch status 13 component targets 14 motherboard targets 15 P power supplies installing 24 powering off 21 47 Index powering on 26 for service removing 22 servicing 21 powering off power supplies 21 switch 21 powering on power supplies 26 preparing for service 17 R rear panel LEDs 9 removing fan module 29 power supplies 22 replaceable components 18 S sensors overview 13 service ESD precautions 17 tools needed 18 servic
Download Pdf Manuals
Related Search