Installation Instructions
Contents
1. U Fire Hazard Aa It is recommended that the washer dryer be exhausted to the outside Pd 4 a l 9 E Check that you If washer dryer is installed in a closet the dryer MUST be exhausted outside Failure to follow these instructions may result in a fire removed all the shipping pieces including the round shipping piece Dispose of alll materials in proper manner If you do not remove the round shipping piece your washer dryer may walk away from its location To prevent large amounts of lint and moisture from accumulating and to maintain drying efficiency and to prevent exposure to possible health hazards this appliance 11 1 cm IS LAD should be exhausted outdoors ean L ZA _ THIS WASHER DRYER MAY BE INSTALLED depi AY 9 IN A RECESSED AREA OR CLOSET The installation spacing is in centimeters and inches and is the minimum allowable Dac Additional spacing should be considered for 19 ease of installation servicing and rear view compliance with local codes and ordinances If closet door is installed the minimum unobstructed air openings in top and 391cm side view bottom are required Louvered doors with 15 3 8 equivalent air openings are acceptable 30 E Check that you have all Closet installation must be exhausted your tools Other installations must use the minimum dimensions indicated 3 1 E Turn on water faucets and Recessed installation check for leaks Tighten couplings if there is2. 24 E if you did not remove the access panel in step 18 remove the two foam shipping pieces between the washer and dryer and place with the other shipping pieces If the exhaust duct cannot be connected from the side of the washer dryer the exhaust duct can be reached from the front through the access panel Remove the two Phillios nead screws located at the top of the access panel set access panel and screws aside 25 E Determine the length of exhaust duct that is needed to connect the dryer to the exhaust hood See Exhaust requirements Panel B duct tape 26 E Connect exhaust duct to washer dryer and then to the exhaust hood e Use the straightest path possible to avoid 90 Turns e Use duct tape to seal all joints in the exhaust system Do Not use screws e Use caulking Compound to seal exterior wall opening around exhaust hood 2 y CHECK ELECTRICAL REQUIREMENTS BE SURE YOU HAVE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED GROUNDING METHOD Check the Installation Instructions to see that you have completed each step Complete any missed steps before you continue 2 M Check that all parts are now installed See parts list Panel B If there is an extra part go back through the steps to see which step was skipped Recessed and closet Product dimensions Shown with legs extended 1 inch f apm a Sohom otwessevanyoo e instructions 6 om WARNING
3. strap plastic beaded strap 23 Make sure the hook end of E drain hose is in laundry tub or standpipe Wrap the plastic beaded strap around the drain hose and tub or standpipe Thread beaded end of strap through keyhole end Pull until strap is tight Slide strap into narrow end of keyhole to lock strap in place See Figures A B If the water inlet faucets and drain standpipe are recessed tightly wrap the plastic beaded strap around the drain hose and faucet body Do Not wrap strap around the faucet handles or stems Thread beaded end of strap through keyhole end Pull until strap is tight Slide strap into narrow end of keyhole to lock strap in place see Figure C Secure the drain hose to the laundry tub or standpipe with the plastic strap Failure to properly secure drain hose could result in water damage If drain hose cannot be strapped into place hose must be cut exactly to length so hook end is held tightly over edge of laundry tub or standpipe If a longer drain hose is needed drain hose Part No 388423 and hose connection kit Part No 285442 are available from your authorized parts distributor If drain hose must be shortened use hose connection kit Part No 285442 Note If washer dryer is moved to adjust drain hose the washer dryer must be leveled again Repeat Step 22 Place cardboard under the washer dryer and carefully move washer dryer to avoid damaging floor covering
4. 5m 5 ft of the center rear of cabinet is required See Electrical requirements Panel A washer dryer 2 5 CM C1 in Support Floor must be sturdy enough to support washer dryer weight with water and clothes of 170 kg 375 Ib Tools and materials needed for installation lt sciewdiiver ES pliers safety glasses AAN Y pliers that open to 3 8 cm 1 1 2 minimum FA ED 1 4 socket wrench or nut driver Eo Electrical requirements WARNING A Electrical Shock Hazard Electrical ground is required Do Not ground to a gas pipe Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician if you are not sure this washer dryer is properly grounded Do Not change the power supply cord plug If it will not fit the outlet have a proper outlet installed by a qualified electrician Do Not have a fuse in the neutral or grounding circuit Do Not use an extension cord with this washer dryer Failure to follow these instructions could result in death or electrical shock AWARNING a Electric Shock Hazard It is the customer s responsibility To contact a qualified electrical installer To assure that the electrical installation is adequate and in conformance with the Canadian Electrical Codes and all local codes and ordinances Failure to follow these instructions can result
5. Do Not use non metal flexible duct Do Not use metal duct smaller than 10 2 cm 4 in in diameter Do Not use exhaust hoods with magnetic latches Check that exhaust system is not longer than specified Exhaust systems longer than specified will Accumulate lint Maximum length of 10 2 cm 4 in dia duct Not recommended 7 3m flexible 24 ft metal duct 5 5 m 18 ft 3 1 m 10 ft Not recommended Now start With washer dryer in laundry area AWARNING Injury Hazard More than one person is required to lift tilt or move the washer dryer because of its weight and size Failure to follow this instruction may result in injury Truck only from the rear to prevent product damage The maximum length using a 5 1 cm x 15 2 cm 2 in x 6 in rectangular duct with 2 elbows and a 6 4 cm 2 1 2 in exhaust hood is 2 4 m 8 ft Shorten the life of the product Reduce performance and result in 1 E Put on safety glasses and gloves longer drying times and increased energy usage Failure to follow specifications may result in a fire Do Not exhaust the dryer into a chimney furnace cold air duct attic or crawl space or any other duct used for venting Clean the exhaust system every year Do Not install flexible duct under wall ceiling or floor materials Accumulated lint could be fuel for a fire or cause moisture damage Exhausting your dryer indoors is Not recomme
6. panel of the washer dryer Use the straightest path you can to avoid 90 turns Maximum length of the exhaust system depends upon the type of duct used number of elbows and the type of exhaust hood The maximum length for both rigid and flexible duct is shown in the chart Panel B For exhaust configurations other than those listed in chart the back pressure MUST not exceed 0 5 cm 0 2 inches water column at the back of the washer dryer The back pressure should be checked by a qualified technician For exhaust systems not covered by the exhaust length chart see Service Manual Part No 603197 available from your authorized parts distributor Service check The back pressure in any exhaust system used must not exceed 0 5 cm 0 2 inches of water column measured with an incline manometer at the point that the exhaust duct connects to the dryer Exhausting the dryer outside is recommended Recessed installation that is not exhausted outside must use Exhaust Deflector Kit Part No 694609 available from your authorized parts distributor See Recessed and closet installation instructions Panel E for unobstructed air opening requirements If the washer dryer is installed in a confined area such as a bedroom bathroom or closet if must be exhausted to the outside and provision must be made for enough air for combustion and ventilation Check governing codes and ordinances Also refer to the Recessed and cl
7. the washer dryer is in place Do Not remove 10 Move foam shipping pieces outward just enough to clear the washer lid Open the washer lid The latch under the dryer will hold lid open A DELIE J w im 4 rng El F 4 aaa Siae 4 me ae Panel C Numbers correspond to steps Li R a 4 H fi i 9 ee a AA E ar Er x ia 11 29 shipping piece 1 1 E Grasp round shipping piece at the front and the back Lift to remove from inside washer ro l l i d 2 E Take hoses out of basket Place hoses with other parts a a oe oe de aoe a a i a a aF a ae ow Numbers correspond to steps Daat _ _ d 3 E Release washer lid by pushing up on latch Close lid Use new hoses and washers that came with your washer dryer coupling washer d 4 E Insert a flat washer into each end of the inlet hoses Check that washers are firmly seated in couplings Inlet valves are plastic Do Not strip or crossthread d 5 E Attach hose to bottom inlet valve opening first Attach second hose to top inlet valve Tighten couplings by hand then use pliers to make an additional two thirds turn IMPORTANT THIS PROCEDURE MUST BE FOLLOWED TO ASSURE PROPER INSTALLATION clamp 0 64cm lt 1 14 max 0 64cm drain drain cias connector hose max 1 6 E lo prevent the drain hose from coming of
8. 0 keep with washer dryer y 310 sq cm 48 sq in A You have just finished installing your new washer dryer To get the most efficient use from your new washer dryer read your Use amp Care Guide Congratulations Keep Installation Instructions nearby where you can refer to them They ll make reinstalling your washer dryer in another home as easy as the first installation Additional space may be needed for exhaust closet door 155 sq cm 24 sq in y gt 25 cm 1 side view Closet installation must be exhausted outdoors Recessed non exhausted installation must use only the rear exhaust position and Exhaust Deflector Kit No 4500 is required Panel E If washer dryer does not operate e Check that the circuit breaker is not tripped or the house fuse blown e Check that power supply cord is plugged into wall receptacle e Check that washer lid or dryer door is closed e Check that the round shipping piece has been removed e Check that controls are set in a running or ON position e Check that dryer START button has been firmly pushed Part No 3405982 1996 When moving the washer dryer e Disconnect the power supply cord Tape power supply cord securely to washer dryer e Tape the dryer drum to the front panel Tape the lint screen in place Tape the dryer door closed e Wedge a blanket between the tub ring and cabi
9. Installation Instructions Four Wire Laundry System Washere Dryer 240 Volt Q co o Q e IMPORTANT D Read and save these instructions IMPORTANT Installer Leave Installation tee with the homeowne Homeowner Keep neocon Instructions for future reference Save Installation Instructions for local electrical insoector s use Part No 3405982 Before you start Check location where washer dryer will be installed Proper installation is your responsibility The washer dryer must not be installed or stored in an area where it will be exposed to water and or weather Make sure you have everything necessary for correct installation Location should be large enough to fully open dryer door 90 See Panel E for Recessed and closet installation instructions and Product dimensions Check utilities Proper electrical supply must be available See Electrical requirements Panel A Dryer may be exhausted from rear or left or right side Exhausting through the side Ta requires Side Exhaust Kit Part No 279823 See Exhaust l requirements Panel B CUCUK 10 2 cm 4 in metal exhaust duct is required Standpipe drain system needs a5cm 2 in diameter standpipe A with a minimum carry br away capacity of 64 4 litres 14 2 Imperial gallons per minute Top of standpipe must be at least 71 1 cm 28 in high and no higher than 121 9 cm 48 in from floor Floor drain
10. e the following steps through the access area d 9 E Put hook end of drain hose in laundry tub or standpipe Check for proper length of drain hose 20 attaching water inlet hoses run water through both faucets into a bucket This will get rid of any particles in water lines that might clog hoses Mark which is the hot water faucet 2 1 E Attach bottom hose inlet marked H to hot water faucet Attach top hose inlet marked C to cold water faucet Tighten the couplings to the faucets by hand Use pliers fo make the final two thirds turn Move washer dryer fo its permanent position Remove cardboard hardboard from under washer dryer Carefully move the mM washer dryer into final position 22 Panel D e Tilt the washer dryer forward raising back legs 2 5 cm 1 inch off the floor so that the rear self leveling legs will adjust Gently lower the washer dryer to the floor Check that the washer dryer is level by placing a carpenter s level on top of the washer first side to side then front to back If it is not level adjust the front legs up or down Tilt the washer dryer forward raising back legs 2 5 cm 1 inch off the floor so that the rear self leveling legs will adjust Gently lower the washer dryer to the floor Check that the washer dryer is level Repeat as needed CHECK THAT DRAIN HOSE IS NOT TWISTED OR KINKED AND IS SECURELY IN PLACE plastic beaded
11. eck that all parts were included E Insert a rear leveling leg into the hole in the rear corner on the bottom of the washer dryer Push leg in until it snaps into place Do the same same thing with the other leveling leg in the other rear corner 5 E Push up one leg check to see that the other leg goes down Check the other leg the same way If legs do not adjust repeat step 4 6 E With one of the front legs in hand check the ridges for a diamond marking That s how far the leg is supposed to go into the hole Start to screw the legs into the holes in the front corners by hand Use slip joint pliers to finish turning the front legs until you reach the diamond mark Slide washer dryer onto cardboard or hardboard before moving across floor to prevent damage to floor covering 7 M Place a piece of cardboard or hardboard in front of carton Now stand the washer dryer upright Slide washer dryer onto cardboard or hardboard To prevent product damage do not remove corner posts before cutting NG Sa 8 E With the corner posts in place cut the carton down one corner Remove carton 9 E Remove the two rear corner posts located at the back of the washer dryer Remove the two corner pieces attached to the lower front of the washer dryer Do Not remove the foam shipping pieces between the washer and dryer until
12. f or leaking if must be installed per the following instructions 1 Wet the inside end of the drain hose with tap water DO NOT USE ANY OTHER LUBRICANT 2 Squeeze ears of small clamp with pliers to open clamp and place clamp over end of drain hose 3 While holding clamp open work end of drain hose onto drain connector until drain hose is within 0 64 cm 1 4 in of ribbed stop 4 Position clamp over the drain hose area marked clamp Release clamp Clamp should be 0 64 cm 1 4 in from end of drain hose Numbers correspond to steps 1 7 E Standpipe or laundry tub drain system Open hose clamp and slide over hook end of drain hose to secure the rigid and corrugated sections together Floor drain system Do Not install hook end of drain hose to corrugated section Consult your plumber for proper installation Slide washer dryer onto cardboard or hardboard before moving across floor to avoid damaging floor 1 8 E if you have room to work from either side of the washer dryer move washer dryer close to final position so you can easily complete the installation steps If you are working in a closet or recessed area move the washer dryer into its final position and remove cardboard hardboard from under washer dryer Remove the two Phillios nhead screws located at the top of the access panel See illustration for Step 24 Remove access panel and set access panel and screws aside Complet
13. i leaking DO NOT OVERTIGHTEN This could y gt H 0 cm 0 cold water inlet 72 7 cm 28 5 8 36 2 cm 14 1 4 recess width 54 1 cm gt 21 5 16 70 2 cm 27 5 8 cause damage to faucets wari 7 6 cm 3 gt 7 5 1 4 144 8 cm 57 182 2 cm M Replace the access panel Be 71 3 4 sure to tighten screws at each end of the access panel 33 E Plug power supply cord into grounded outlet 130 9 cm 51 1 2 3 A front view side view E Read the Use and Care Guide Minimum installation spacing to fully understand your new washer dryer Now start the washer and allow it to Note If recessed installation is exhausted all spacing can be 0 cm 0 in complete the regular cycle Additional clearance for wall door and floor molding may be required Closet installation y closet door 69 2 cm 27 1 4 310 sq cm 48 sq in 7 6 cm 3 35 M Remove tape from dryer door and open dryer door Remove tape across 7 6 cm 3 the dryer lint screen Check to be sure lint J 155 sq cm 24 sq in screen is in its proper position Wipe out drum i with a damp cloth to remove any dust Start dryer and allow it to complete a heat cycle A to make sure the dryer is working properly front view Unobstructed air openings are minimum for closet door Louvered door with equivalent air openings is acceptable 36 E Finally save all literature and lt 0 cm
14. in death or electrical shock Hot and cold water faucets must be within 1 2 meters 4 feet of the back of the washer dryer and provide water pressure of 34 to 690 kPa 5 100 psi Water heater Set to deliver 60 C 140 F water to the washer Laundry tub drain system needs a 75 7 litres 16 7 Imperial gallons laundry tub Top of tub must be at least 71 1 cm 28 in high and no higher than 121 9 cm 48 in from floor If a longer drain hose is needed Drain Hose Part No 388423 and Hose Connection kit Part No 285442 are available from your EN authorized parts distributor A Do Not store or operate washer dryer below 0 C 32 F some water may remain in washer Proper operation of dryer cycles requires temperatures above 7 C 45 F See Use amp Care Guide for Winterizing information OBSERVE ALL GOVERNING CODES AND ORDINANCES 1 A four wire single phase 120 240 volt 60 Hz AC only electrical supply is required on a separate 30 ampere circuit fused on both sides of the line ime delay fuse or Circuit breaker is recommended 2 This washer dryer is equipped with a four wire 30 amp rated flexible tyoe power supply cord It must be plugged into a mating 30 amp receptacle NEMA type 14 30R See Figure 1 Use 30 amp receptacle where local codes permit flexible type supply cord pigtail 14 30R 4 wire receptacle Figure 1 Exhaust requirements A WARNING ONY g Fire Hazard
15. nded The moisture and lint indoors may cause Lint to gather inside and around the dryer and be a fuel for fire Moisture damage to woodwork furniture paint wallpaper carpet etc Housecleaning problems and possible health problems Failure to follow these instructions could result in fire damage injury or health problems If using an existing exhaust system clean lint from entire length of exhaust system Make sure exhaust hood is not plugged with lint The exhaust system should be inspected and cleaned yearly Replace any vinyl or metallized plastic foil exhaust duct with rigid metal or flexible metal duct Use duct tape to seal alll joints Do Not use screws To secure duct exhaust air flow 10 2 cm 4 in rigid metal pipe better good is preferred Plan installation to use the fewest number of elbows and turns Metal flexible duct must be fully extended and supported when the dryer is in its final position DO NOT KINK OR CRUSH THE DUCT The metal flexible duct must be fully extended to allow adequate exhaust air to flow Allow as much room as possible when using elbows or making turns Bend duct gradually to avoid kinking Remove excess flexible duct to avoid sagging and kinking that may result in reduced air flow The exhaust duct can be routed up down left right or straight out the back of the washer dryer Soace requirements are provided on Panel E and on the rear
16. net top to restrict tub movement e Turn front leveling legs all the way in BRANCHES ACROSS CANADA If you need assistance Check your Use and Care Guide for a toll free number to call or call the dealer from whom you purchased this appliance The dealer is listed in the Yellow Pages of your pohone directory under Appliances Household Major Service and Repair When you call you will need the washer dryer model number and serial number Both numbers can be found on the model serial rating plate located behind the dryer door on the dryer door wall Inglis Limited 1901 Minnesota Court Mississauga Ontario LON 3A7 Washers Dryers Refrigerators e Dishwashers e Waste Compactors Microwave Ovens Printed in U S A
17. oset installation instructions on Panel E An exhaust hood should cap the exhaust duct to prevent exhausted air from returning hood must be at least 30 5 cm 12 in from the i ground or any object that o may be in the path of the exhaust 10 2 cm 4 in outlet hood is preferred However a 6 4 cm 2 1 2 in outlet may be used with short systems only A 6 4 cm 2 1 2 in outlet can result in longer drying times than other hood types For permanent installation a stationary exhaust system is required Exhausting the dryer through the side of the washer dryer requires the use of Side Exhaust Kit Part No 279823 ia An Follow kit instructions for oroper exhaust installation Mobile home installation __outside wall ZILLI LLL LLL LLL LLL LLLA skirting floor enclosed area Mobile home exhaust requirements The washer dryer must have an outside exhaust If the dryer is exhausted through the floor and the area under the mobile home is enclosed the exhaust system must terminate outside the enclosed area Extension beyond the enclosure will prevent lint and moisture buildup under the mobile home into dryer The outlet of the ain minimum shipping cardboard base e 4 legs e 1 drain hose front legs clamp e 1 plastic beaded strap e 4 flat water hose washers 1 small clamp 3 E Remove parts from plastic package Ch
18. system requires a siphon break Part No 285320 available from your authorized parts distributor SEE RECESSED AND CLOSET INSTALLATION INSTRUCTIONS ON PANELE AWARNING Z di f Fire Hazard For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage personal injury or loss of life Do Not use or store gasoline paint thinners and other flammable materials near washer dryer Fumes from such materials could result in fire or explosion Never install washer dryer up against draperies or curtains or on carpet To do so may result in a fire Keep any and all items from falling or collecting behind the washer dryer Failure to do so may result in a fire Replace all access panels before operating washer dryer Failure to follow these instructions may result in a fire A WARNING Injury Hazard More than one person is required to lift tilt or move this washer dryer because of its weight and size Failure to follow these instructions may result in injury Panel A Drain hose may also be installed to a laundry tub or floor drain IAr Important Observe all governing codes and ordinances Check code requirements Some codes limit or do not permit the installation of washer dryer in garages closets mobile homes and sleeping quarters Contact your local building inspector Grounded electrical outlet within 1
Download Pdf Manuals
Related Search