Illuminated kick plate_G35 sedan_G6950 1NM0A
Contents
1. GENUINE PARTS INFINITI INSTALLATION INSTRUCTIONS 1 DESCRIPTION Illuminated Kick Plate 2 APPLICATION G37 SEDAN 2012 Starting Vin No JNIDV6AP2CM810618 3 PART NUMBER G6950 1INMOA KIT CONTENTS TOOLS REQUIRED Nylon Removal Tool Wire cutter e 10mm Socket and driver 14mm socket and driver Fish tape e Masking tape Flash light Scissors e Soap and water 50 50 alcohol amp water solution Soft non linting towel page 1 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 6 PRE INSTALLATION CAUTIONS NOTES A CAUTION e Dealer Installation Recommended Instructions refer to Service Manual e Please read this instruction carefully before installing this product for correct installation e Please DO NOT use or install the part in ways other than what is described in this instruction manual e If problem occurs during installation please contact Nissan dealer where you purchased the product 1 Apply Parking Brake 2 Make sure the shift lever is engaged in P or N position 3 Record customer Radio Presets 4 Use seat and floor protection 5 Open the hood of the vehicle 6 Disconnect the negative battery terminal to prevent short circuits during installation 7 This part is to be installed at a surface temperature of 65 100 F 8 Do not wash the vehicle for 24 hours after installing to prevent the double sided tape from peeling A CAUTION e Care must be ta2. Connect the connectors and apply the Urethane foam tape F on the connecting section as shown FRONT Urethane foam tape F In Fig21 Lamp Unit vt l Harness 7 Attach excessive lamp harness to the vehicle harness with a Tie wrap E as shown in Fig20 1 place 8 Cut excessive Tie wrap Fig 21 Urethane foam tape F mM Vehicle Flange KN 7J Urethane foam tape F A CAUTION e Do not attach the harness to sharp metal edge Page 12 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 14 REAR KICK PLATE INSTALLATION The procedure below shows the installation for LH side Repeat procedure for RH side Fig 22 1 Remove the vehicle weather strip near the Kick plate rear C attachment location as shown in Weather strip Fig22 2 Clean the attachment area of Kick plate rear C with soapy water 3 Dry area with soft non linting towel 4 Clean area with 50 50 alcohol amp water solution and let dry for 30 seconds 5 Pull the double sided tape liner pull tab to Kick plate rear C partially remove liner Using masking tape hold the liner to the visible side of the Kick plate rear C surface as shown in Fig23 6 Align clips on part to hole on vehicle from Masking tape front side 7 Set part on vehicle being careful to keep the Tape s Liner outside edge of the part parallel to the rocker panel 9 Gradually remove the tape liner at the back of th
3. Instrument Lower Panel LH removal Instrument Lower Panel LH 8 f T 1 a Remove Hood Opener Mounting Bolts b Pull downward Instrument Lower Panel LH to disengage pawls and clips Shown in Fig8 c Disconnect harness from Instrument Lower Panel LH and hose plug d Remove Instrument Lower Panel LH 8 nN Metal Boltsx2 pawlsx3 clipsx4 Page 6 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 10 WIRING HARNESS INSTALLATION 4a CAUTION e Connector pull test should be less than 10kgf 22 Ibs to confirm secure connection to vehicle connector Harness D Urethane foam tape F 1 Wrap the fuse of Harness D with two pieces of Urethane foam tape F Shown in Fig9 2 Conect the THO4FW connector of Harness D and Option connector THO4MW of vehicle Shown in Fig10 3 Attach the Harness D to vehicle harness at the position shown in Fig 10 using the Tie wrap E 2 places Vehicle Nest Vth r a AF THO4FW Harness D Harness D S Tie wrap E Fuge AW ADNI 4 Attach the Harness D to vehicle harness at the position shown in Fig11 Secure by using the Tie wrap E 2 places Tie wrap E Harness D Page 7 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 10 WIRING HARNESS INSTALLATION CONT D 5 Flip the carpet of the driver s side 6 Route Harness D under accelerator pedal bracket and a
4. e Kick plate rear C starting from the front apply minimum 11lb 49N of pressure along the part to attach tape to body as shown in Fig23 Masking tape Kick plate rear C _ Keep Kick plate rear C and vehicle body parallel 4 Press bond 4a CAUTION Use caution when applying pressure as the surface may dent Page 13 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 14 CHECK AFTER INSTALLATION 1 Please check that the installation has no problem LJ a confirm connection of connector LJ b confirm whether wire harness is fixed 15 FUNCTION CHECK L 1 Re connect battery negative terminal CI 2 Confirm all switch function are working on Instrument Lower Panel LH LJ 3 Confirm INFINITI text is illuminated when either door is in the opened position Manual engage door switch to verify Illuminated Kick Plate ON OFF function is working 16 REINSTALLATION OF REMOVED PARTS LJ 1 All removed vehicle parts have been reinstalled 44 CAUTION Use caution when re installing interior components to avoid damage scratch or breaking of mounting clips LJ 2 Clean interior of vehicle 17 VEHICLE CHECK 1 Remove all tools from the vehicle 2 Inspect reinstalled interior trim parts for proper panel fit 3 Reset radio presets to the recorded setting 4 Turn ignition to ON position 5 Confirm proper radio operation 6 Initialize sun roof and power window opera
5. epeat steps A to C until it is OK f Disconnect battery Page 9 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Il CLIP TO A KICK PLATE INSTALLATION The procedure below shows the installation for LH side Repeat procedure for RH side 1 Slide clip H into the Clip Seat as shown in Fig16 and Fig17 Clip Seat Kick plate front A Page 10 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 12 FRONT KICK PLATE INSTALLATION The procedure below shows the installation for LH side Repeat procedure for RH side 1 Remove the vehicle weather strip near the Kick plate front A attachment location shown in Fig18 Weather strip 2 Clean the attachment area of Kick plate front A with soapy water 3 Dry area with soft non linting towel 4 Clean area with 50 50 alcohol amp water solution and let dry for 30 seconds 5 Pull the double sided tape liner pull tab to partially remove liner Using masking tape hold the liner to the visible side of the Kick plate front A surface as shown in Fig19 Kick plate front LH A 6 Align clips on part to first and fourth hole on Masking tape vehicle from front side 7 Set part on vehicle being careful to keep the outside edge of the part parallel to the rocker Tape s Liner panel 8 Gradually remove the tape liner at the back of the Kick plate front A starting from the front apply minimum 11
6. k Plate Outer LH 2 Rear Kick Plate Outer LH 2 3 Front Kick Plate Inner LH removal ah PY a Pull up Front Kick Plate Inner LH and disconnect pawls Shown in Fig3 b Remove Front Kick Plate Inner LH 3 Page 4 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 9 VEHICLE PARTS REMOVAL 4 Front Kick Plate Outer LH removal a Remove Front Kick Plate Outer LH mounting clips with nylon removal tool Shown in Fig4 b Remove Front Kick Plate Outer LH 4 5 Dashboard Side Lower Panel LH removal a Remove clip A b Detach Dashboard Side Lower Panel LH mounting clips with nylon removal tool Shown in Fig5 c Remove Dashboard Side Lower Panel LH 5 removal tool 6 Glove Box Lower Cover removal a Pull downward disengaged pawls b Remove Glove Box Lower Cover 6 Shown in Fig6 Glove Box Lower Cover 6 7 Repeat steps 1 to 5 for RH side of vehicle Rear Kick Plate Inner RH 9 Rear Kick Plate Outer RH 10 Front Kick Plate Inner RH 11 Front Kick Plate Outer RH 12 Dashboard Side Lower Panel RH 13 Page 5 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 9 VEHICLE PARTS REMOVAL CONT D 8 Instrument Side Finisher LH removal a Insert a nylon remover tool into lower space b Pull the Instrument Side Finisher LH crosswise Shown in Fig7 c Remove Instrument Side Finisher LH 7 nylon removal FEAA WAN OAN 9
7. ken not to scratch or damage any components during the removal or replacement process 9 Remove the following interior trim parts in the sequence shown below Remove sequence Rear Kick Plate Inner LH Rear Kick Plate Outer LH Front kick Plate Inner LH Front Kick Plate Outer LH Dashboard Side Lower Panel LH Glove Box Lower Cover Instrument Side Finisher LH Instrument Lower Panel LH 9 Rear Kick Plate Inner RH 10 Rear Kick Plate Outer RH 11 Front kick Plate Inner RH 12 Front Kick Plate Outer RH 13 Dashboard Side Lower panel RH 1 2 3 4 5 6 7 8 Page 2 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate fi INSTALLATION OUTLINE in Short Harness for LH Long Harness for RH 8 STANDARD CONNECTION METHOD Option connector Room lam battery saver power Room lamp output THO4MW NH THO4FW NH Vehicle wiring color description is just for reference Please refer to vehicle wiring diagram for details Page 3 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 9 VEHICLE PARTS REMOVAL 1 Rear Kick Plate Inner LH removal a Pull up Rear Kick Plate Inner LH and disconnect pawls Shown in Fig1 b Remove Rear Kick Plate Inner LH 1 D a os Rear Kick Plate Inner LH 1 2 Rear Kick Plate Outer LH removal a Remove Rear Kick Plate Outer LH mounting clips with nylon removal tool Shown in Fig2 b Remove Rear Kic
8. lb 49N of pressure along the part to attach tape to body shown in Fig19 _ 3 Mt pa eee eee tee a 2 eT _ Keep Kick Plate A and vehicle body parallel 4 Press bond 4a CAUTION e Use caution when applying pressure as the surface may dent e During installation be careful not to allow the harness to get stuck between the vehicle and the kick plate e Harness should be routed through the notched area of the kick plate Page 11 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 13 HARNESS CONNECTION INSTALLATION The procedure below shows the installation for LH side Repeat procedure for RH side Kick plate LH A LS ILNA 1 Secure harness D to vehicle harness at connector with Tie Wrap E as shown in Fig20 1 place 2 Fold one piece Urethane foam tape F and cut into two equal pieces y 3 Clean both sides of the attachment area for the Kick plate LH A Urethane foam tape F with the 50 50 alcohol E a amp water solution Let dry for 30 seconds Shown in Fig20 yy 4 Attach the cut piece of Urethane foam tape F Pa to vehicle flange as shown in Fig21 Ii i 5 Place the lamp harness on top of the Urethane foam tape F then apply second half of the Tr Detail A Urethane foam tape F on top of the harness Urethane foam tape F Reference Detail A Harness routing of Vehicle Flange Straight Diagonally Vehicle Flange 6
9. tion 7 Confirm proper operation of the rear window washer fluid 8 Confirm the functionality of all four blinkers and hazard warning signal flasher 9 Confirm the operation of all door lock and unlock using remote key LJ 10 Reset windows When window is completely up continue to hold in up position for 4 seconds LJ 11 Turn ignition to off position OOOOUOUOUOOO A CAUTION During restoring please use caution to avoid the pinching or breaking of the vehicle s harness or damage any other parts Page 14 of 14 G6950 1NMOA II 11 29 11
10. ttach harness to floor using the Flat wire protector G shown in Fig12 4 places 7 Remove one push nut from front passenger s side carpet Shown in Fig13 8 Flip the carpet of passenger s side 9 Route fish tape behind center console from driver s side harness to passenger s side 10 Pull harness with fish tape behind center console 11 Attach passenger s side harness to floor using the Flat wire protector G shown in Fig13 5 places 12 Route Harness D through existing vehicle harness protector and attach the Harness D to vehicle harness at the position shown in Fig14 using the Tie wrap E 3 places Tie wrap E Harness D Driver s side Page 8 of 14 G6950 1NMOA II 11 29 11 INSTALLATION INSTRUCTIONS Illuminated Kick Plate 10 WIRING HARNESS INSTALLATION CONT D 13 Route Harness D through existing vehicle harness a protector and attach the Harness D to vehicle SS harness at the position shown in Fig15 using re i gt Tie wrap E 3 places SN Harness D Tie wrap E Passenger s side 14 Function check a Connect Harness D to the lamp unit harness of Kick plate A and B b Connect battery c Check function Confirm INFINITI text illuminates when either door is open d If OK disconnect Harness D from the lamp unit harness of Kick plate A and B e If NG check harness routine connections and lamp unit to identify root cause and fix it R
Download Pdf Manuals
Related Search