INSTALLATION MANuAL
Contents
1. Ground WHITE WIRE Parking Light Output RED WIRE 12 Volts RED WHITE WIRE Parking Light Input a ee ee i Sos nNonsk REPLACEMENT REMOTE PART REMOTE 6888 rpoOwO Ff ODN OC AUXILIARY 2 5 6888 ADDITIONAL INFORMATION AUXILIARY ONE Grey Wire maybe used for either Trunk Release default or Remote Starter Programmable feature 3 Press and relase AUX button to release trunk OR engage Remote Starter e lf Gray Wire is used for Trunk Release the system will disarm and unlock vehicle e lf Gray wire is connected to enable Remote Starter the system will bypass sensor and ignition e Programmable feature 3 must be programmed to either Trunk Release default or Remote Starter a SECOND AUXILIARY or HORN OUTPUT Brown White Wire has four programmable options programmable feature 4 1 PULSE Provides a negative output as long as Lock and Panic are pressed and held together Default 2 LATCH OUTPUT Provides a negative output for 25 seconds when Lock and Panic buttons are pressed together at the same time and released 3 HORN Horn and siren work together only on all alarm events Siren will work on all events 4 LIMITED HORN Horn enables when alarm is triggered Horn does not activate when lock unlock is pressed on the remote only the siren chirps NOTE Programmable feature 4 must be programmed to how the Brown White wire is connected and in2. the LOCK and PANIC buttons are held Note 3 LATCH Press LOCK and PANIC buttons for a 30 second signal output Note 4 HORN The Horn wire will have an output whenever the Siren wire has an output Note 5 LIMITED HORN The Horn will sound only during Door Trigger Ignition or when the Shock Sensor is triggered The siren will sound chirp on all events Note 6 If ignition hi jack is enabled you must disable hi jack using the valet button before entering programming mode Leave ignition on after turning off hi jack See ignition hi jack on page 8 4 B LED INDICATION TABLE Type of Trigger in Armed Mode LED Status No Trigger LED Flash rapidly Auto Rearm Activated Pin Switch Zone 2 Flash amp 1 Pause FEATURES z Siren Chirp once Indicator LED flash once i 2A JUMPER PIN INFORMATION Jumper 1 OPEN Last Door Arm Auto Rearm OFF CLOSE Last Door Arm Auto Rearm ON Jumper 2 OPEN Last Door Arm Auto Rearm without Door Lock CLOSE Last Door Arm Auto Rearm with Door Lock Jumper 3 OPEN Dome Light Delay for 60sec ON CLOSE Dome Light Delay for 60sec OFF Jumper 4 OPEN Central Door Lock CDL Pulse Timer 3 5sec CLOSE Central Door Lock CDL Pulse Timer 0 5sec Default setting for all jumpers is CLOSED 2 B POWER HARNESS WIRING CONFIGURATION Pin 1 RED WHITE PARKING LIGHT INPUT VOLTAGE e This Input will provide the Voltage and Polarity to White Wire fused at 10 Amps Pin 2 RED
3. 6 ANTI HI JACK MODE There are three different ways to activate Anti Hi Jack AHJ 1 By Ignition Programmable Feature 7 Default setting is OFF When Programmable Feature 7 is ON and the ignition is turned on the alarm will enter AHJ mode The siren will chirp three times and the LED will flash fast Note If programmable feature 7 hi jack through ignition is enabled ON you must exit hi jack mode using the valet button before entering programming mode see section 4 to enter programming mode Do not turn ignition off leave ignition on then press valet button 5 times to enter programming mode By Door Programmable Feature 8 Default setting is OFF When Programmable Feature 8 is ON and when the Ignition is ON AND the driver door is opened then closed alarm will enter AHJ mode The siren will chirp three times and the LED will flash fast By Remote Control Programmable Feature 9 Default setting is OFF When Programmable Feature 9 is ON and Ignition ON Press and hold PANIC and AUX together for 2 seconds alarm will enter AHJ mode Siren will chirp three times and LED will flash fast NOTE All three features can be set to ON ANTI HI JACK MODE ACTIVATED STATUS From 0 60 sec LED will flash quickly From 61 70 sec LED will flash quickly siren chirps and the parking light will flash From 71 80 sec LED will flash quickly siren chirps parking light will flash and ignition cut output constantly Afte
4. LEASE e Press and hold the AUX button for 2 SECONDS for Alarm must be DISARMED SILENT ARMING and Lock Doors and ignition OFF e Press and hold the AUX button for 2 SECONDS for Alarm must be ARMED and SILENT DISARMING and Unlock Doors ignition OFF VALET OVERRIDE SWITCH OPERATION USED FOR 1 Stopping horn siren Turn ignition on press and hold valet switch until horn siren stops 2 To enter exit keyless basic mode LED steady on Ignition on and hold valet switch for 5 seconds 3 Use to program remotes Turn ignition on press and release valet switch 5 times press lock buttons on each remote to be programmed turn ignition off Up to 4 remotes may be programmed Most Common Locations Ask installer where it is located Ss e Inside glove compartment driver s kick panel behind the fuse panel access door underneath the dashboard in front of the driver REPLACEMENT REMOTE PART NUMBER REMOTE 6888 THIS IS ONLY A GUIDE These instructions are a general guideline of possible applications Specifications may change dependent upon vehicle Always review the vehicle s service manual and wiring diagram when performing an installation Manufacturer does not assume any responsibility for damages to property or persons which may occur due to incorrect applications or product failure Not responsible for typographical errors Specifications are subject to change without notice Warranty void if not installed by authorized dealer S
5. MAIN POWER CONNECTION 12V e Connect to the 12V Battery Terminal Fused at 15 Amps Pin 3 WHITE PARKING LIGHT OUTPUT e Connect this Wire to the Vehicle 12 Volts Parking Light Circuit e This Output will provide a Flashing 12 Volts fused at 10 Amps to energize vehicle s Parking Light Pin 4 BLACK GROUND e Connect this wire to Chassis ground Pin 5 BROWN SIREN OUTPUT e This wire will provide a 12Volts positive Output for powering a Siren 3A Pin 6 YELLOW IGNITION INPUT e Connect to the Vehicle 12 Volt Ignition Wire Pin 7 GRAY AUXILIARY TRUNK RELEASE OUTPUT 500mA e This wire will provide a 12V Negative output e May be used for remote starter see programmable feature 3 3 2 B POWER HARNESS WIRING CONFIGURATION CONTINUED Pin 8 GREEN Negative Trigger Door Input e This Input will trigger the Alarm if it becomes Grounded while alarm is armed if door is opened Pin 9 N A Pin 10 PURPLE Positive Trigger Door Input e This Input will trigger the Alarm if it receive 12 Volts while alarm is armed if door is opened Pin 11 ORANGE Starter Kill Output e This output needs to be used with a relay to be cut into the vehicle starter wire Pin 12 BLUE Hood Pin Input e This Input will trigger the Alarm if it becomes Grounded while alarm is armed if the hood is opened Pin 13 BROWN WHITE 2nd Auxiliary or horn honk output Note Controll
6. d shock sensor triggers e To Stop Panic Mode if Remote is Lost or Not Present e With Ignition ON hold Valet switch until Horn Siren stops e To Exit from Hi jack mode e Turn on ignition then press override switch for 1 sec The sys tem will be in disarm mode 4 PROGRAMMABLE FEATURES To change any of the programmable features please follow these steps 1 Turn ignition ON 2 Press Valet Override switch 5 times the siren horn will chirp once and parking light and LED will stay on 3 Press the Valet switch the number of times equal to the number of the feature to be programmed 4 Press the button to be programmed LOCK UNLOCK PANIC AUX on the remote to choose the setting you desire 5 Turn ignition OFF Note If 10 seconds expire without any programming activity the parking light and LED will turn OFF and the System will return to Disarm mode 5
7. ed through programmable feature 4 Pin 14 N A Pin 15 BLACK WHITE Dome Light Supervision e This wire will provide a 0 60 sec for illuminated vehicle when Alarm is Disarmed Pin 16 N A 2 C SHOCK SENSOR Adjust Sensitivity for best protection 1 If car receives light Impact siren horn will chirp 5 times in quick succession and Parking Light will Flash once for warning purpose 2 If car receives heavy impact siren horn will sound and Parking Lights will Flash for 60 sec NOTE Shock Sensor will sound maximum of 5 times then will reset to deactive until armed again 2 D 2 PIN HARNESS LOCK UNLOCK WIRING CONFIGURATION GREEN Connect this Wire to Vehicle Lock Wire BLUE Connect this Wire to Vehicle Unlock Wire Note For vacuum operated door lock system remove jumper pin 4 Use Optional Part RRAL DL to add door lock on board relay interface 3 VALET OVERRIDE SWITCH OPERATION The Valet switch has five functions e To Program Remote Controls see Section 1 How to Code Learn a Remote Control e To Program the Programmable Features see Section 4 Programmable Features e Basic Keyless Entry Mode e With Ignition ON hold Valet switch for 5 seconds repeat to exit e Only locks and unlocks doors Horn and siren only work in Panic Mode LED steady on e NOTE This is different from Programmable Feature 6 which does Keyless Entry where all features work except door hood an
8. pecification and date are subject to change or withdrawal without notice 2011 Micro Alarm Inc 6888 Inst oct2011 indd 1 HOW TO CODE LEARN A REMOTE CONTROL When Car Alarm is Disarmed and Ignition is off 1 Turn Ignition To ON Position 2 Press Valet Override Switch 5 Times Siren Horn will Chirp Once and Parking Light and LED will stay ON 3 Press LOCK on each remote to be programmed Siren Horn will chirp and parking light will flash to confirm remote has been programmed 4 Turn Ignition OFF Note 1 After 10 seconds without any programming activity or if the ignition is turned OFF the System will automatically exit Remote Control Programming Mode Note 2 Up 4 Remote Controls can be programmed 2 JUMPER PIN AND WIRING CONFIGURATION SHOCK SENSOR l WHITE CONNECTOR DOOR LOCK RED CONNECTOR zdf Ldr LED WHITE CONNECTOR Ge 13W11 SjNd IAO NIdO tdf ny uuy 100q se NJ3dO 0 43W11 S Nd 109 GASO19 n O n il O i O 7a a aaso79 SI Sdf T1V 404 LINVAAC ALON 98S Wey NO O OD BLACK WHITE WIRE Dome Light Output N A BROWN WHITE WIRE 2nd AUX Horn BLUE WIRE Hood Pin Input ORANGE WIRE Starter Disable PURPLE WIRE Door Trigger Input N A GREEN WIRE Door Trigger Input GREY WIRE Trunk Release Output Aux YELLOW WIRE Ignition Input BROWN WIRE Siren Output 3 Amp BLACK WIRE
9. r 81 sec LED will flash quickly siren chirps parking light will flash and ignition cut output constantly EXIT ANTI HI JACK MODE From 00 60 sec Turn on the ignition then press and hold UNLOCK button for 2 sec The system will be in disarm mode After 60 sec Turn on ignition then press override switch for 1 sec The system will be in disarm mode A 4 eee Pa O WW Wl Gwar Wa 6888 INSTALLATION MANUAL LOCK BUTTON e Press and release the LOCK button to ARM ALARM Ignition must be OFF and LOCK DOORS e Press and release the LOCK button to LOCK DOORS During Valet Mode e Press and release LOCK button and press it again for Ignition must be OFF 2 SECONDS to BYBASS SHOCK SENSOR and ARM ALARM Use this to bypass shock sensor e Press and release the UNLOCK button to DISARM Alarm must be ARMED and ALARM and UNLOCK DOORS Ignition OFF e Press and release the UNLOCK button to STOP When siren horn is Sounding ALARM TRIGGER e Press and release the UNLOCK button to UNLOCK During Driving or Valet Mode DOOR e Press and Hold the UNLOCK button for 2 SECONDS _ Alarm must be DISARMED to switch ALARM to KEYLESS basic mode and Ignition ON e Press and hold the PANIC but en Press LOCK and PANIC buttons ton for 2 SECONDS to TRIGGER together to get AUX2 Output HORN SIREN Note Contact installer to make sure this option is enabled AUX BUTTON e Press and release the AUX button for TRUNK RE
10. tended to be used ONLY ONE OPTION MAY BE SELECTED AND PROGRAMMED LOCK IF PULSE IS WIRED CONFIGURED Default IF LATCH IS WIRED CONFIGURED Press and Release Lock and Panic at same time to geta negative output for 25 seconds PRESS A negative output will ae bg provided by pressing and holding Lock and Panic at the same time Output will be provided as long as Lock and Panic are held A gt PROGRAMMABLE FEATURE TABLE Lock Unlock Single Double Pulse Disarm Parking Flash Light Light O P Twice 30 sec Disarm Trunk Car Start 1st AUX see Note 1 1 Short Chirp 2nd AUX Horn Pulse Latch Horn Limited Horn 1 Short see Note 2 See Note 3 See Note 4 see Note 5 Chirp 1 Short Chirp IGN Lock Unlock Keyless Entry 1 Short Chirp IGN Anti 1 Short Hi Jack Chirp Door 1 Short Anit Hi Jack Chirp Remote Anit 1 Short Hi Jack Chirp Back to Press AUX for 3 seconds Siren will chirp 6 times 1 Short Factory Default Light will flash 6 times All features will be returned Chirp to default settings All settings shaded in gray are factory default settings a Note 1 CAR START Press and release AUX button to get a 0 5 second negative output on the 1st channel trunk release wire This will bypass the sensor and ignition Note 2 PULSE Press and hold the LOCK and PANIC buttons and the 2nd Channel Output will send signal as long as
Download Pdf Manuals
Related Search